diff options
Diffstat (limited to 'drivers/tty')
| -rw-r--r-- | drivers/tty/n_gsm.c | 10 | ||||
| -rw-r--r-- | drivers/tty/serial/Kconfig | 8 | ||||
| -rw-r--r-- | drivers/tty/serial/Makefile | 1 | ||||
| -rw-r--r-- | drivers/tty/serial/bfin_sport_uart.c | 3 | ||||
| -rw-r--r-- | drivers/tty/serial/imx.c | 3 | ||||
| -rw-r--r-- | drivers/tty/serial/lantiq.c | 756 | ||||
| -rw-r--r-- | drivers/tty/serial/mfd.c | 4 | ||||
| -rw-r--r-- | drivers/tty/serial/mrst_max3110.c | 2 | ||||
| -rw-r--r-- | drivers/tty/serial/of_serial.c | 7 | ||||
| -rw-r--r-- | drivers/tty/tty_ioctl.c | 2 |
10 files changed, 784 insertions, 12 deletions
diff --git a/drivers/tty/n_gsm.c b/drivers/tty/n_gsm.c index 720160acd9d..a4c42a75a3b 100644 --- a/drivers/tty/n_gsm.c +++ b/drivers/tty/n_gsm.c @@ -1645,8 +1645,12 @@ static void gsm_queue(struct gsm_mux *gsm) if ((gsm->control & ~PF) == UI) gsm->fcs = gsm_fcs_add_block(gsm->fcs, gsm->buf, gsm->len); - /* generate final CRC with received FCS */ - gsm->fcs = gsm_fcs_add(gsm->fcs, gsm->received_fcs); + if (gsm->encoding == 0){ + /* WARNING: gsm->received_fcs is used for gsm->encoding = 0 only. + In this case it contain the last piece of data + required to generate final CRC */ + gsm->fcs = gsm_fcs_add(gsm->fcs, gsm->received_fcs); + } if (gsm->fcs != GOOD_FCS) { gsm->bad_fcs++; if (debug & 4) @@ -2110,7 +2114,7 @@ static int gsmld_attach_gsm(struct tty_struct *tty, struct gsm_mux *gsm) /** * gsmld_detach_gsm - stop doing 0710 mux - * @tty: tty atttached to the mux + * @tty: tty attached to the mux * @gsm: mux * * Shutdown and then clean up the resources used by the line discipline diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig index c01af80d12a..636144cea93 100644 --- a/drivers/tty/serial/Kconfig +++ b/drivers/tty/serial/Kconfig @@ -1391,6 +1391,14 @@ config SERIAL_OF_PLATFORM_NWPSERIAL_CONSOLE help Support for Console on the NWP serial ports. +config SERIAL_LANTIQ + bool "Lantiq serial driver" + depends on LANTIQ + select SERIAL_CORE + select SERIAL_CORE_CONSOLE + help + Support for console and UART on Lantiq SoCs. + config SERIAL_QE tristate "Freescale QUICC Engine serial port support" depends on QUICC_ENGINE diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile index aafddf15992..cb2628fee4c 100644 --- a/drivers/tty/serial/Makefile +++ b/drivers/tty/serial/Makefile @@ -94,4 +94,5 @@ obj-$(CONFIG_SERIAL_IFX6X60) += ifx6x60.o obj-$(CONFIG_SERIAL_PCH_UART) += pch_uart.o obj-$(CONFIG_SERIAL_MSM_SMD) += msm_smd_tty.o obj-$(CONFIG_SERIAL_MXS_AUART) += mxs-auart.o +obj-$(CONFIG_SERIAL_LANTIQ) += lantiq.o obj-$(CONFIG_SERIAL_XILINX_PS_UART) += xilinx_uartps.o diff --git a/drivers/tty/serial/bfin_sport_uart.c b/drivers/tty/serial/bfin_sport_uart.c index c3ec0a61d85..891d194ae75 100644 --- a/drivers/tty/serial/bfin_sport_uart.c +++ b/drivers/tty/serial/bfin_sport_uart.c @@ -296,8 +296,7 @@ static int sport_startup(struct uart_port *port) IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING | IRQF_DISABLED, "BFIN_SPORT_UART_CTS", up)) { up->cts_pin = -1; - dev_info(port->dev, "Unable to attach BlackFin UART \ - over SPORT CTS interrupt. So, disable it.\n"); + dev_info(port->dev, "Unable to attach BlackFin UART over SPORT CTS interrupt. So, disable it.\n"); } } if (up->rts_pin >= 0) diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c index df6828654f4..a54473123e0 100644 --- a/drivers/tty/serial/imx.c +++ b/drivers/tty/serial/imx.c @@ -380,12 +380,13 @@ static void imx_start_tx(struct uart_port *port) static irqreturn_t imx_rtsint(int irq, void *dev_id) { struct imx_port *sport = dev_id; - unsigned int val = readl(sport->port.membase + USR1) & USR1_RTSS; + unsigned int val; unsigned long flags; spin_lock_irqsave(&sport->port.lock, flags); writel(USR1_RTSD, sport->port.membase + USR1); + val = readl(sport->port.membase + USR1) & USR1_RTSS; uart_handle_cts_change(&sport->port, !!val); wake_up_interruptible(&sport->port.state->port.delta_msr_wait); diff --git a/drivers/tty/serial/lantiq.c b/drivers/tty/serial/lantiq.c new file mode 100644 index 00000000000..58cf279ed87 --- /dev/null +++ b/drivers/tty/serial/lantiq.c @@ -0,0 +1,756 @@ +/* + * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published + * by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + * Copyright (C) 2004 Infineon IFAP DC COM CPE + * Copyright (C) 2007 Felix Fietkau <nbd@openwrt.org> + * Copyright (C) 2007 John Crispin <blogic@openwrt.org> + * Copyright (C) 2010 Thomas Langer, <thomas.langer@lantiq.com> + */ + +#include <linux/slab.h> +#include <linux/module.h> +#include <linux/ioport.h> +#include <linux/init.h> +#include <linux/console.h> +#include <linux/sysrq.h> +#include <linux/device.h> +#include <linux/tty.h> +#include <linux/tty_flip.h> +#include <linux/serial_core.h> +#include <linux/serial.h> +#include <linux/platform_device.h> +#include <linux/io.h> +#include <linux/clk.h> + +#include <lantiq_soc.h> + +#define PORT_LTQ_ASC 111 +#define MAXPORTS 2 +#define UART_DUMMY_UER_RX 1 +#define DRVNAME "ltq_asc" +#ifdef __BIG_ENDIAN +#define LTQ_ASC_TBUF (0x0020 + 3) +#define LTQ_ASC_RBUF (0x0024 + 3) +#else +#define LTQ_ASC_TBUF 0x0020 +#define LTQ_ASC_RBUF 0x0024 +#endif +#define LTQ_ASC_FSTAT 0x0048 +#define LTQ_ASC_WHBSTATE 0x0018 +#define LTQ_ASC_STATE 0x0014 +#define LTQ_ASC_IRNCR 0x00F8 +#define LTQ_ASC_CLC 0x0000 +#define LTQ_ASC_ID 0x0008 +#define LTQ_ASC_PISEL 0x0004 +#define LTQ_ASC_TXFCON 0x0044 +#define LTQ_ASC_RXFCON 0x0040 +#define LTQ_ASC_CON 0x0010 +#define LTQ_ASC_BG 0x0050 +#define LTQ_ASC_IRNREN 0x00F4 + +#define ASC_IRNREN_TX 0x1 +#define ASC_IRNREN_RX 0x2 +#define ASC_IRNREN_ERR 0x4 +#define ASC_IRNREN_TX_BUF 0x8 +#define ASC_IRNCR_TIR 0x1 +#define ASC_IRNCR_RIR 0x2 +#define ASC_IRNCR_EIR 0x4 + +#define ASCOPT_CSIZE 0x3 +#define TXFIFO_FL 1 +#define RXFIFO_FL 1 +#define ASCCLC_DISS 0x2 +#define ASCCLC_RMCMASK 0x0000FF00 +#define ASCCLC_RMCOFFSET 8 +#define ASCCON_M_8ASYNC 0x0 +#define ASCCON_M_7ASYNC 0x2 +#define ASCCON_ODD 0x00000020 +#define ASCCON_STP 0x00000080 +#define ASCCON_BRS 0x00000100 +#define ASCCON_FDE 0x00000200 +#define ASCCON_R 0x00008000 +#define ASCCON_FEN 0x00020000 +#define ASCCON_ROEN 0x00080000 +#define ASCCON_TOEN 0x00100000 +#define ASCSTATE_PE 0x00010000 +#define ASCSTATE_FE 0x00020000 +#define ASCSTATE_ROE 0x00080000 +#define ASCSTATE_ANY (ASCSTATE_ROE|ASCSTATE_PE|ASCSTATE_FE) +#define ASCWHBSTATE_CLRREN 0x00000001 +#define ASCWHBSTATE_SETREN 0x00000002 +#define ASCWHBSTATE_CLRPE 0x00000004 +#define ASCWHBSTATE_CLRFE 0x00000008 +#define ASCWHBSTATE_CLRROE 0x00000020 +#define ASCTXFCON_TXFEN 0x0001 +#define ASCTXFCON_TXFFLU 0x0002 +#define ASCTXFCON_TXFITLMASK 0x3F00 +#define ASCTXFCON_TXFITLOFF 8 +#define ASCRXFCON_RXFEN 0x0001 +#define ASCRXFCON_RXFFLU 0x0002 +#define ASCRXFCON_RXFITLMASK 0x3F00 +#define ASCRXFCON_RXFITLOFF 8 +#define ASCFSTAT_RXFFLMASK 0x003F +#define ASCFSTAT_TXFFLMASK 0x3F00 +#define ASCFSTAT_TXFREEMASK 0x3F000000 +#define ASCFSTAT_TXFREEOFF 24 + +static void lqasc_tx_chars(struct uart_port *port); +static struct ltq_uart_port *lqasc_port[MAXPORTS]; +static struct uart_driver lqasc_reg; +static DEFINE_SPINLOCK(ltq_asc_lock); + +struct ltq_uart_port { + struct uart_port port; + struct clk *clk; + unsigned int tx_irq; + unsigned int rx_irq; + unsigned int err_irq; +}; + +static inline struct +ltq_uart_port *to_ltq_uart_port(struct uart_port *port) +{ + return container_of(port, struct ltq_uart_port, port); +} + +static void +lqasc_stop_tx(struct uart_port *port) +{ + return; +} + +static void +lqasc_start_tx(struct uart_port *port) +{ + unsigned long flags; + spin_lock_irqsave(<q_asc_lock, flags); + lqasc_tx_chars(port); + spin_unlock_irqrestore(<q_asc_lock, flags); + return; +} + +static void +lqasc_stop_rx(struct uart_port *port) +{ + ltq_w32(ASCWHBSTATE_CLRREN, port->membase + LTQ_ASC_WHBSTATE); +} + +static void +lqasc_enable_ms(struct uart_port *port) +{ +} + +static int +lqasc_rx_chars(struct uart_port *port) +{ + struct tty_struct *tty = tty_port_tty_get(&port->state->port); + unsigned int ch = 0, rsr = 0, fifocnt; + + if (!tty) { + dev_dbg(port->dev, "%s:tty is busy now", __func__); + return -EBUSY; + } + fifocnt = + ltq_r32(port->membase + LTQ_ASC_FSTAT) & ASCFSTAT_RXFFLMASK; + while (fifocnt--) { + u8 flag = TTY_NORMAL; + ch = ltq_r8(port->membase + LTQ_ASC_RBUF); + rsr = (ltq_r32(port->membase + LTQ_ASC_STATE) + & ASCSTATE_ANY) | UART_DUMMY_UER_RX; + tty_flip_buffer_push(tty); + port->icount.rx++; + + /* + * Note that the error handling code is + * out of the main execution path + */ + if (rsr & ASCSTATE_ANY) { + if (rsr & ASCSTATE_PE) { + port->icount.parity++; + ltq_w32_mask(0, ASCWHBSTATE_CLRPE, + port->membase + LTQ_ASC_WHBSTATE); + } else if (rsr & ASCSTATE_FE) { + port->icount.frame++; + ltq_w32_mask(0, ASCWHBSTATE_CLRFE, + port->membase + LTQ_ASC_WHBSTATE); + } + if (rsr & ASCSTATE_ROE) { + port->icount.overrun++; + ltq_w32_mask(0, ASCWHBSTATE_CLRROE, + port->membase + LTQ_ASC_WHBSTATE); + } + + rsr &= port->read_status_mask; + + if (rsr & ASCSTATE_PE) + flag = TTY_PARITY; + else if (rsr & ASCSTATE_FE) + flag = TTY_FRAME; + } + + if ((rsr & port->ignore_status_mask) == 0) + tty_insert_flip_char(tty, ch, flag); + + if (rsr & ASCSTATE_ROE) + /* + * Overrun is special, since it's reported + * immediately, and doesn't affect the current + * character + */ + tty_insert_flip_char(tty, 0, TTY_OVERRUN); + } + if (ch != 0) + tty_flip_buffer_push(tty); + tty_kref_put(tty); + return 0; +} + +static void +lqasc_tx_chars(struct uart_port *port) +{ + struct circ_buf *xmit = &port->state->xmit; + if (uart_tx_stopped(port)) { + lqasc_stop_tx(port); + return; + } + + while (((ltq_r32(port->membase + LTQ_ASC_FSTAT) & + ASCFSTAT_TXFREEMASK) >> ASCFSTAT_TXFREEOFF) != 0) { + if (port->x_char) { + ltq_w8(port->x_char, port->membase + LTQ_ASC_TBUF); + port->icount.tx++; + port->x_char = 0; + continue; + } + + if (uart_circ_empty(xmit)) + break; + + ltq_w8(port->state->xmit.buf[port->state->xmit.tail], + port->membase + LTQ_ASC_TBUF); + xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); + port->icount.tx++; + } + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(port); +} + +static irqreturn_t +lqasc_tx_int(int irq, void *_port) +{ + unsigned long flags; + struct uart_port *port = (struct uart_port *)_port; + spin_lock_irqsave(<q_asc_lock, flags); + ltq_w32(ASC_IRNCR_TIR, port->membase + LTQ_ASC_IRNCR); + spin_unlock_irqrestore(<q_asc_lock, flags); + lqasc_start_tx(port); + return IRQ_HANDLED; +} + +static irqreturn_t +lqasc_err_int(int irq, void *_port) +{ + unsigned long flags; + struct uart_port *port = (struct uart_port *)_port; + spin_lock_irqsave(<q_asc_lock, flags); + /* clear any pending interrupts */ + ltq_w32_mask(0, ASCWHBSTATE_CLRPE | ASCWHBSTATE_CLRFE | + ASCWHBSTATE_CLRROE, port->membase + LTQ_ASC_WHBSTATE); + spin_unlock_irqrestore(<q_asc_lock, flags); + return IRQ_HANDLED; +} + +static irqreturn_t +lqasc_rx_int(int irq, void *_port) +{ + unsigned long flags; + struct uart_port *port = (struct uart_port *)_port; + spin_lock_irqsave(<q_asc_lock, flags); + ltq_w32(ASC_IRNCR_RIR, port->membase + LTQ_ASC_IRNCR); + lqasc_rx_chars(port); + spin_unlock_irqrestore(<q_asc_lock, flags); + return IRQ_HANDLED; +} + +static unsigned int +lqasc_tx_empty(struct uart_port *port) +{ + int status; + status = ltq_r32(port->membase + LTQ_ASC_FSTAT) & ASCFSTAT_TXFFLMASK; + return status ? 0 : TIOCSER_TEMT; +} + +static unsigned int +lqasc_get_mctrl(struct uart_port *port) +{ + return TIOCM_CTS | TIOCM_CAR | TIOCM_DSR; +} + +static void +lqasc_set_mctrl(struct uart_port *port, u_int mctrl) +{ +} + +static void +lqasc_break_ctl(struct uart_port *port, int break_state) +{ +} + +static int +lqasc_startup(struct uart_port *port) +{ + struct ltq_uart_port *ltq_port = to_ltq_uart_port(port); + int retval; + + port->uartclk = clk_get_rate(ltq_port->clk); + + ltq_w32_mask(ASCCLC_DISS | ASCCLC_RMCMASK, (1 << ASCCLC_RMCOFFSET), + port->membase + LTQ_ASC_CLC); + + ltq_w32(0, port->membase + LTQ_ASC_PISEL); + ltq_w32( + ((TXFIFO_FL << ASCTXFCON_TXFITLOFF) & ASCTXFCON_TXFITLMASK) | + ASCTXFCON_TXFEN | ASCTXFCON_TXFFLU, + port->membase + LTQ_ASC_TXFCON); + ltq_w32( + ((RXFIFO_FL << ASCRXFCON_RXFITLOFF) & ASCRXFCON_RXFITLMASK) + | ASCRXFCON_RXFEN | ASCRXFCON_RXFFLU, + port->membase + LTQ_ASC_RXFCON); + /* make sure other settings are written to hardware before + * setting enable bits + */ + wmb(); + ltq_w32_mask(0, ASCCON_M_8ASYNC | ASCCON_FEN | ASCCON_TOEN | + ASCCON_ROEN, port->membase + LTQ_ASC_CON); + + retval = request_irq(ltq_port->tx_irq, lqasc_tx_int, + IRQF_DISABLED, "asc_tx", port); + if (retval) { + pr_err("failed to request lqasc_tx_int\n"); + return retval; + } + + retval = request_irq(ltq_port->rx_irq, lqasc_rx_int, + IRQF_DISABLED, "asc_rx", port); + if (retval) { + pr_err("failed to request lqasc_rx_int\n"); + goto err1; + } + + retval = request_irq(ltq_port->err_irq, lqasc_err_int, + IRQF_DISABLED, "asc_err", port); + if (retval) { + pr_err("failed to request lqasc_err_int\n"); + goto err2; + } + + ltq_w32(ASC_IRNREN_RX | ASC_IRNREN_ERR | ASC_IRNREN_TX, + port->membase + LTQ_ASC_IRNREN); + return 0; + +err2: + free_irq(ltq_port->rx_irq, port); +err1: + free_irq(ltq_port->tx_irq, port); + return retval; +} + +static void +lqasc_shutdown(struct uart_port *port) +{ + struct ltq_uart_port *ltq_port = to_ltq_uart_port(port); + free_irq(ltq_port->tx_irq, port); + free_irq(ltq_port->rx_irq, port); + free_irq(ltq_port->err_irq, port); + + ltq_w32(0, port->membase + LTQ_ASC_CON); + ltq_w32_mask(ASCRXFCON_RXFEN, ASCRXFCON_RXFFLU, + port->membase + LTQ_ASC_RXFCON); + ltq_w32_mask(ASCTXFCON_TXFEN, ASCTXFCON_TXFFLU, + port->membase + LTQ_ASC_TXFCON); +} + +static void +lqasc_set_termios(struct uart_port *port, + struct ktermios *new, struct ktermios *old) +{ + unsigned int cflag; + unsigned int iflag; + unsigned int divisor; + unsigned int baud; + unsigned int con = 0; + unsigned long flags; + + cflag = new->c_cflag; + iflag = new->c_iflag; + + switch (cflag & CSIZE) { + case CS7: + con = ASCCON_M_7ASYNC; + break; + + case CS5: + case CS6: + default: + new->c_cflag &= ~ CSIZE; + new->c_cflag |= CS8; + con = ASCCON_M_8ASYNC; + break; + } + + cflag &= ~CMSPAR; /* Mark/Space parity is not supported */ + + if (cflag & CSTOPB) + con |= ASCCON_STP; + + if (cflag & PARENB) { + if (!(cflag & PARODD)) + con &= ~ASCCON_ODD; + else + con |= ASCCON_ODD; + } + + port->read_status_mask = ASCSTATE_ROE; + if (iflag & INPCK) + port->read_status_mask |= ASCSTATE_FE | ASCSTATE_PE; + + port->ignore_status_mask = 0; + if (iflag & IGNPAR) + port->ignore_status_mask |= ASCSTATE_FE | ASCSTATE_PE; + + if (iflag & IGNBRK) { + /* + * If we're ignoring parity and break indicators, + * ignore overruns too (for real raw support). + */ + if (iflag & IGNPAR) + port->ignore_status_mask |= ASCSTATE_ROE; + } + + if ((cflag & CREAD) == 0) + port->ignore_status_mask |= UART_DUMMY_UER_RX; + + /* set error signals - framing, parity and overrun, enable receiver */ + con |= ASCCON_FEN | ASCCON_TOEN | ASCCON_ROEN; + + spin_lock_irqsave(<q_asc_lock, flags); + + /* set up CON */ + ltq_w32_mask(0, con, port->membase + LTQ_ASC_CON); + + /* Set baud rate - take a divider of 2 into account */ + baud = uart_get_baud_rate(port, new, old, 0, port->uartclk / 16); + divisor = uart_get_divisor(port, baud); + divisor = divisor / 2 - 1; + + /* disable the baudrate generator */ + ltq_w32_mask(ASCCON_R, 0, port->membase + LTQ_ASC_CON); + + /* make sure the fractional divider is off */ + ltq_w32_mask(ASCCON_FDE, 0, port->membase + LTQ_ASC_CON); + + /* set up to use divisor of 2 */ + ltq_w32_mask(ASCCON_BRS, 0, port->membase + LTQ_ASC_CON); + + /* now we can write the new baudrate into the register */ + ltq_w32(divisor, port->membase + LTQ_ASC_BG); + + /* turn the baudrate generator back on */ + ltq_w32_mask(0, ASCCON_R, port->membase + LTQ_ASC_CON); + + /* enable rx */ + ltq_w32(ASCWHBSTATE_SETREN, port->membase + LTQ_ASC_WHBSTATE); + + spin_unlock_irqrestore(<q_asc_lock, flags); + + /* Don't rewrite B0 */ + if (tty_termios_baud_rate(new)) + tty_termios_encode_baud_rate(new, baud, baud); +} + +static const char* +lqasc_type(struct uart_port *port) +{ + if (port->type == PORT_LTQ_ASC) + return DRVNAME; + else + return NULL; +} + +static void +lqasc_release_port(struct uart_port *port) +{ + if (port->flags & UPF_IOREMAP) { + iounmap(port->membase); + port->membase = NULL; + } +} + +static int +lqasc_request_port(struct uart_port *port) +{ + struct platform_device *pdev = to_platform_device(port->dev); + struct resource *res; + int size; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + dev_err(&pdev->dev, "cannot obtain I/O memory region"); + return -ENODEV; + } + size = resource_size(res); + + res = devm_request_mem_region(&pdev->dev, res->start, + size, dev_name(&pdev->dev)); + if (!res) { + dev_err(&pdev->dev, "cannot request I/O memory region"); + return -EBUSY; + } + + if (port->flags & UPF_IOREMAP) { + port->membase = devm_ioremap_nocache(&pdev->dev, + port->mapbase, size); + if (port->membase == NULL) + return -ENOMEM; + } + return 0; +} + +static void +lqasc_config_port(struct uart_port *port, int flags) +{ + if (flags & UART_CONFIG_TYPE) { + port->type = PORT_LTQ_ASC; + lqasc_request_port(port); + } +} + +static int +lqasc_verify_port(struct uart_port *port, + struct serial_struct *ser) +{ + int ret = 0; + if (ser->type != PORT_UNKNOWN && ser->type != PORT_LTQ_ASC) + ret = -EINVAL; + if (ser->irq < 0 || ser->irq >= NR_IRQS) + ret = -EINVAL; + if (ser->baud_base < 9600) + ret = -EINVAL; + return ret; +} + +static struct uart_ops lqasc_pops = { + .tx_empty = lqasc_tx_empty, + .set_mctrl = lqasc_set_mctrl, + .get_mctrl = lqasc_get_mctrl, + .stop_tx = lqasc_stop_tx, + .start_tx = lqasc_start_tx, + .stop_rx = lqasc_stop_rx, + .enable_ms = lqasc_enable_ms, + .break_ctl = lqasc_break_ctl, + .startup = lqasc_startup, + .shutdown = lqasc_shutdown, + .set_termios = lqasc_set_termios, + .type = lqasc_type, + .release_port = lqasc_release_port, + .request_port = lqasc_request_port, + .config_port = lqasc_config_port, + .verify_port = lqasc_verify_port, +}; + +static void +lqasc_console_putchar(struct uart_port *port, int ch) +{ + int fifofree; + + if (!port->membase) + return; + + do { + fifofree = (ltq_r32(port->membase + LTQ_ASC_FSTAT) + & ASCFSTAT_TXFREEMASK) >> ASCFSTAT_TXFREEOFF; + } while (fifofree == 0); + ltq_w8(ch, port->membase + LTQ_ASC_TBUF); +} + + +static void +lqasc_console_write(struct console *co, const char *s, u_int count) +{ + struct ltq_uart_port *ltq_port; + struct uart_port *port; + unsigned long flags; + + if (co->index >= MAXPORTS) + return; + + ltq_port = lqasc_port[co->index]; + if (!ltq_port) + return; + + port = <q_port->port; + + spin_lock_irqsave(<q_asc_lock, flags); + uart_console_write(port, s, count, lqasc_console_putchar); + spin_unlock_irqrestore(<q_asc_lock, flags); +} + +static int __init +lqasc_console_setup(struct console *co, char *options) +{ + struct ltq_uart_port *ltq_port; + struct uart_port *port; + int baud = 115200; + int bits = 8; + int parity = 'n'; + int flow = 'n'; + + if (co->index >= MAXPORTS) + return -ENODEV; + + ltq_port = lqasc_port[co->index]; + if (!ltq_port) + return -ENODEV; + + port = <q_port->port; + + port->uartclk = clk_get_rate(ltq_port->clk); + + if (options) + uart_parse_options(options, &baud, &parity, &bits, &flow); + return uart_set_options(port, co, baud, parity, bits, flow); +} + +static struct console lqasc_console = { + .name = "ttyLTQ", + .write = lqasc_console_write, + .device = uart_console_device, + .setup = lqasc_console_setup, + .flags = CON_PRINTBUFFER, + .index = -1, + .data = &lqasc_reg, +}; + +static int __init +lqasc_console_init(void) +{ + register_console(&lqasc_console); + return 0; +} +console_initcall(lqasc_console_init); + +static struct uart_driver lqasc_reg = { + .owner = THIS_MODULE, + .driver_name = DRVNAME, + .dev_name = "ttyLTQ", + .major = 0, + .minor = 0, + .nr = MAXPORTS, + .cons = &lqasc_console, +}; + +static int __init +lqasc_probe(struct platform_device *pdev) +{ + struct ltq_uart_port *ltq_port; + struct uart_port *port; + struct resource *mmres, *irqres; + int tx_irq, rx_irq, err_irq; + struct clk *clk; + int ret; + + mmres = platform_get_resource(pdev, IORESOURCE_MEM, 0); + irqres = platform_get_resource(pdev, IORESOURCE_IRQ, 0); + if (!mmres || !irqres) + return -ENODEV; + + if (pdev->id >= MAXPORTS) + return -EBUSY; + + if (lqasc_port[pdev->id] != NULL) + return -EBUSY; + + clk = clk_get(&pdev->dev, "fpi"); + if (IS_ERR(clk)) { + pr_err("failed to get fpi clk\n"); + return -ENOENT; + } + + tx_irq = platform_get_irq_byname(pdev, "tx"); + rx_irq = platform_get_irq_byname(pdev, "rx"); + err_irq = platform_get_irq_byname(pdev, "err"); + if ((tx_irq < 0) | (rx_irq < 0) | (err_irq < 0)) + return -ENODEV; + + ltq_port = kzalloc(sizeof(struct ltq_uart_port), GFP_KERNEL); + if (!ltq_port) + return -ENOMEM; + + port = <q_port->port; + + port->iotype = SERIAL_IO_MEM; + port->flags = ASYNC_BOOT_AUTOCONF | UPF_IOREMAP; + port->ops = &lqasc_pops; + port->fifosize = 16; + port->type = PORT_LTQ_ASC, + port->line = pdev->id; + port->dev = &pdev->dev; + + port->irq = tx_irq; /* unused, just to be backward-compatibe */ + port->mapbase = mmres->start; + + ltq_port->clk = clk; + + ltq_port->tx_irq = tx_irq; + ltq_port->rx_irq = rx_irq; + ltq_port->err_irq = err_irq; + + lqasc_port[pdev->id] = ltq_port; + platform_set_drvdata(pdev, ltq_port); + + ret = uart_add_one_port(&lqasc_reg, port); + + return ret; +} + +static struct platform_driver lqasc_driver = { + .driver = { + .name = DRVNAME, + .owner = THIS_MODULE, + }, +}; + +int __init +init_lqasc(void) +{ + int ret; + + ret = uart_register_driver(&lqasc_reg); + if (ret != 0) + return ret; + + ret = platform_driver_probe(&lqasc_driver, lqasc_probe); + if (ret != 0) + uart_unregister_driver(&lqasc_reg); + + return ret; +} + +module_init(init_lqasc); + +MODULE_DESCRIPTION("Lantiq serial port driver"); +MODULE_LICENSE("GPL"); diff --git a/drivers/tty/serial/mfd.c b/drivers/tty/serial/mfd.c index c111f36f5d2..cab52f4a88b 100644 --- a/drivers/tty/serial/mfd.c +++ b/drivers/tty/serial/mfd.c @@ -49,8 +49,8 @@ static int hsu_dma_enable; module_param(hsu_dma_enable, int, 0); -MODULE_PARM_DESC(hsu_dma_enable, "It is a bitmap to set working mode, if \ -bit[x] is 1, then port[x] will work in DMA mode, otherwise in PIO mode."); +MODULE_PARM_DESC(hsu_dma_enable, + "It is a bitmap to set working mode, if bit[x] is 1, then port[x] will work in DMA mode, otherwise in PIO mode."); struct hsu_dma_buffer { u8 *buf; diff --git a/drivers/tty/serial/mrst_max3110.c b/drivers/tty/serial/mrst_max3110.c index 2f548af4e98..1bd28450ca4 100644 --- a/drivers/tty/serial/mrst_max3110.c +++ b/drivers/tty/serial/mrst_max3110.c @@ -56,7 +56,7 @@ struct uart_max3110 { wait_queue_head_t wq; struct task_struct *main_thread; struct task_struct *read_thread; - struct mutex thread_mutex;; + struct mutex thread_mutex; u32 baud; u16 cur_conf; diff --git a/drivers/tty/serial/of_serial.c b/drivers/tty/serial/of_serial.c index 0e8eec516df..c911b2419ab 100644 --- a/drivers/tty/serial/of_serial.c +++ b/drivers/tty/serial/of_serial.c @@ -80,14 +80,17 @@ static int __devinit of_platform_serial_setup(struct platform_device *ofdev, /* * Try to register a serial port */ +static struct of_device_id of_platform_serial_table[]; static int __devinit of_platform_serial_probe(struct platform_device *ofdev) { + const struct of_device_id *match; struct of_serial_info *info; struct uart_port port; int port_type; int ret; - if (!ofdev->dev.of_match) + match = of_match_device(of_platform_serial_table, &ofdev->dev); + if (!match) return -EINVAL; if (of_find_property(ofdev->dev.of_node, "used-by-rtas", NULL)) @@ -97,7 +100,7 @@ static int __devinit of_platform_serial_probe(struct platform_device *ofdev) if (info == NULL) return -ENOMEM; - port_type = (unsigned long)ofdev->dev.of_match->data; + port_type = (unsigned long)match->data; ret = of_platform_serial_setup(ofdev, port_type, &port); if (ret) goto out; diff --git a/drivers/tty/tty_ioctl.c b/drivers/tty/tty_ioctl.c index ef44ddcb137..53f2442c609 100644 --- a/drivers/tty/tty_ioctl.c +++ b/drivers/tty/tty_ioctl.c @@ -307,7 +307,7 @@ EXPORT_SYMBOL(tty_termios_input_baud_rate); * @ospeed: output speed * * Encode the speeds set into the passed termios structure. This is - * used as a library helper for drivers os that they can report back + * used as a library helper for drivers so that they can report back * the actual speed selected when it differs from the speed requested * * For maximal back compatibility with legacy SYS5/POSIX *nix behaviour |