diff options
Diffstat (limited to 'drivers/tty/serial/atmel_serial.c')
| -rw-r--r-- | drivers/tty/serial/atmel_serial.c | 2653 |
1 files changed, 2653 insertions, 0 deletions
diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c new file mode 100644 index 00000000000..c4f75031410 --- /dev/null +++ b/drivers/tty/serial/atmel_serial.c @@ -0,0 +1,2653 @@ +/* + * Driver for Atmel AT91 / AT32 Serial ports + * Copyright (C) 2003 Rick Bronson + * + * Based on drivers/char/serial_sa1100.c, by Deep Blue Solutions Ltd. + * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o. + * + * DMA support added by Chip Coldwell. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + */ +#include <linux/module.h> +#include <linux/tty.h> +#include <linux/ioport.h> +#include <linux/slab.h> +#include <linux/init.h> +#include <linux/serial.h> +#include <linux/clk.h> +#include <linux/console.h> +#include <linux/sysrq.h> +#include <linux/tty_flip.h> +#include <linux/platform_device.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/of_gpio.h> +#include <linux/dma-mapping.h> +#include <linux/atmel_pdc.h> +#include <linux/atmel_serial.h> +#include <linux/uaccess.h> +#include <linux/platform_data/atmel.h> +#include <linux/timer.h> +#include <linux/gpio.h> +#include <linux/gpio/consumer.h> +#include <linux/err.h> +#include <linux/irq.h> + +#include <asm/io.h> +#include <asm/ioctls.h> + +#define PDC_BUFFER_SIZE 512 +/* Revisit: We should calculate this based on the actual port settings */ +#define PDC_RX_TIMEOUT (3 * 10) /* 3 bytes */ + +#if defined(CONFIG_SERIAL_ATMEL_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) +#define SUPPORT_SYSRQ +#endif + +#include <linux/serial_core.h> + +#include "serial_mctrl_gpio.h" + +static void atmel_start_rx(struct uart_port *port); +static void atmel_stop_rx(struct uart_port *port); + +#ifdef CONFIG_SERIAL_ATMEL_TTYAT + +/* Use device name ttyAT, major 204 and minor 154-169. This is necessary if we + * should coexist with the 8250 driver, such as if we have an external 16C550 + * UART. */ +#define SERIAL_ATMEL_MAJOR 204 +#define MINOR_START 154 +#define ATMEL_DEVICENAME "ttyAT" + +#else + +/* Use device name ttyS, major 4, minor 64-68. This is the usual serial port + * name, but it is legally reserved for the 8250 driver. */ +#define SERIAL_ATMEL_MAJOR TTY_MAJOR +#define MINOR_START 64 +#define ATMEL_DEVICENAME "ttyS" + +#endif + +#define ATMEL_ISR_PASS_LIMIT 256 + +/* UART registers. CR is write-only, hence no GET macro */ +#define UART_PUT_CR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_CR) +#define UART_GET_MR(port) __raw_readl((port)->membase + ATMEL_US_MR) +#define UART_PUT_MR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_MR) +#define UART_PUT_IER(port,v) __raw_writel(v, (port)->membase + ATMEL_US_IER) +#define UART_PUT_IDR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_IDR) +#define UART_GET_IMR(port) __raw_readl((port)->membase + ATMEL_US_IMR) +#define UART_GET_CSR(port) __raw_readl((port)->membase + ATMEL_US_CSR) +#define UART_GET_CHAR(port) __raw_readl((port)->membase + ATMEL_US_RHR) +#define UART_PUT_CHAR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_THR) +#define UART_GET_BRGR(port) __raw_readl((port)->membase + ATMEL_US_BRGR) +#define UART_PUT_BRGR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_BRGR) +#define UART_PUT_RTOR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_RTOR) +#define UART_PUT_TTGR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_TTGR) +#define UART_GET_IP_NAME(port) __raw_readl((port)->membase + ATMEL_US_NAME) +#define UART_GET_IP_VERSION(port) __raw_readl((port)->membase + ATMEL_US_VERSION) + + /* PDC registers */ +#define UART_PUT_PTCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_PTCR) +#define UART_GET_PTSR(port) __raw_readl((port)->membase + ATMEL_PDC_PTSR) + +#define UART_PUT_RPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RPR) +#define UART_GET_RPR(port) __raw_readl((port)->membase + ATMEL_PDC_RPR) +#define UART_PUT_RCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RCR) +#define UART_PUT_RNPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RNPR) +#define UART_PUT_RNCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RNCR) + +#define UART_PUT_TPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_TPR) +#define UART_PUT_TCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_TCR) +#define UART_GET_TCR(port) __raw_readl((port)->membase + ATMEL_PDC_TCR) + +struct atmel_dma_buffer { + unsigned char *buf; + dma_addr_t dma_addr; + unsigned int dma_size; + unsigned int ofs; +}; + +struct atmel_uart_char { + u16 status; + u16 ch; +}; + +#define ATMEL_SERIAL_RINGSIZE 1024 + +/* + * We wrap our port structure around the generic uart_port. + */ +struct atmel_uart_port { + struct uart_port uart; /* uart */ + struct clk *clk; /* uart clock */ + int may_wakeup; /* cached value of device_may_wakeup for times we need to disable it */ + u32 backup_imr; /* IMR saved during suspend */ + int break_active; /* break being received */ + + bool use_dma_rx; /* enable DMA receiver */ + bool use_pdc_rx; /* enable PDC receiver */ + short pdc_rx_idx; /* current PDC RX buffer */ + struct atmel_dma_buffer pdc_rx[2]; /* PDC receier */ + + bool use_dma_tx; /* enable DMA transmitter */ + bool use_pdc_tx; /* enable PDC transmitter */ + struct atmel_dma_buffer pdc_tx; /* PDC transmitter */ + + spinlock_t lock_tx; /* port lock */ + spinlock_t lock_rx; /* port lock */ + struct dma_chan *chan_tx; + struct dma_chan *chan_rx; + struct dma_async_tx_descriptor *desc_tx; + struct dma_async_tx_descriptor *desc_rx; + dma_cookie_t cookie_tx; + dma_cookie_t cookie_rx; + struct scatterlist sg_tx; + struct scatterlist sg_rx; + struct tasklet_struct tasklet; + unsigned int irq_status; + unsigned int irq_status_prev; + + struct circ_buf rx_ring; + + struct serial_rs485 rs485; /* rs485 settings */ + struct mctrl_gpios *gpios; + int gpio_irq[UART_GPIO_MAX]; + unsigned int tx_done_mask; + bool ms_irq_enabled; + bool is_usart; /* usart or uart */ + struct timer_list uart_timer; /* uart timer */ + int (*prepare_rx)(struct uart_port *port); + int (*prepare_tx)(struct uart_port *port); + void (*schedule_rx)(struct uart_port *port); + void (*schedule_tx)(struct uart_port *port); + void (*release_rx)(struct uart_port *port); + void (*release_tx)(struct uart_port *port); +}; + +static struct atmel_uart_port atmel_ports[ATMEL_MAX_UART]; +static DECLARE_BITMAP(atmel_ports_in_use, ATMEL_MAX_UART); + +#ifdef SUPPORT_SYSRQ +static struct console atmel_console; +#endif + +#if defined(CONFIG_OF) +static const struct of_device_id atmel_serial_dt_ids[] = { + { .compatible = "atmel,at91rm9200-usart" }, + { .compatible = "atmel,at91sam9260-usart" }, + { /* sentinel */ } +}; + +MODULE_DEVICE_TABLE(of, atmel_serial_dt_ids); +#endif + +static inline struct atmel_uart_port * +to_atmel_uart_port(struct uart_port *uart) +{ + return container_of(uart, struct atmel_uart_port, uart); +} + +#ifdef CONFIG_SERIAL_ATMEL_PDC +static bool atmel_use_pdc_rx(struct uart_port *port) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + + return atmel_port->use_pdc_rx; +} + +static bool atmel_use_pdc_tx(struct uart_port *port) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + + return atmel_port->use_pdc_tx; +} +#else +static bool atmel_use_pdc_rx(struct uart_port *port) +{ + return false; +} + +static bool atmel_use_pdc_tx(struct uart_port *port) +{ + return false; +} +#endif + +static bool atmel_use_dma_tx(struct uart_port *port) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + + return atmel_port->use_dma_tx; +} + +static bool atmel_use_dma_rx(struct uart_port *port) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + + return atmel_port->use_dma_rx; +} + +static unsigned int atmel_get_lines_status(struct uart_port *port) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + unsigned int status, ret = 0; + + status = UART_GET_CSR(port); + + mctrl_gpio_get(atmel_port->gpios, &ret); + + if (!IS_ERR_OR_NULL(mctrl_gpio_to_gpiod(atmel_port->gpios, + UART_GPIO_CTS))) { + if (ret & TIOCM_CTS) + status &= ~ATMEL_US_CTS; + else + status |= ATMEL_US_CTS; + } + + if (!IS_ERR_OR_NULL(mctrl_gpio_to_gpiod(atmel_port->gpios, + UART_GPIO_DSR))) { + if (ret & TIOCM_DSR) + status &= ~ATMEL_US_DSR; + else + status |= ATMEL_US_DSR; + } + + if (!IS_ERR_OR_NULL(mctrl_gpio_to_gpiod(atmel_port->gpios, + UART_GPIO_RI))) { + if (ret & TIOCM_RI) + status &= ~ATMEL_US_RI; + else + status |= ATMEL_US_RI; + } + + if (!IS_ERR_OR_NULL(mctrl_gpio_to_gpiod(atmel_port->gpios, + UART_GPIO_DCD))) { + if (ret & TIOCM_CD) + status &= ~ATMEL_US_DCD; + else + status |= ATMEL_US_DCD; + } + + return status; +} + +/* Enable or disable the rs485 support */ +void atmel_config_rs485(struct uart_port *port, struct serial_rs485 *rs485conf) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + unsigned int mode; + unsigned long flags; + + spin_lock_irqsave(&port->lock, flags); + + /* Disable interrupts */ + UART_PUT_IDR(port, atmel_port->tx_done_mask); + + mode = UART_GET_MR(port); + + /* Resetting serial mode to RS232 (0x0) */ + mode &= ~ATMEL_US_USMODE; + + atmel_port->rs485 = *rs485conf; + + if (rs485conf->flags & SER_RS485_ENABLED) { + dev_dbg(port->dev, "Setting UART to RS485\n"); + atmel_port->tx_done_mask = ATMEL_US_TXEMPTY; + if ((rs485conf->delay_rts_after_send) > 0) + UART_PUT_TTGR(port, rs485conf->delay_rts_after_send); + mode |= ATMEL_US_USMODE_RS485; + } else { + dev_dbg(port->dev, "Setting UART to RS232\n"); + if (atmel_use_pdc_tx(port)) + atmel_port->tx_done_mask = ATMEL_US_ENDTX | + ATMEL_US_TXBUFE; + else + atmel_port->tx_done_mask = ATMEL_US_TXRDY; + } + UART_PUT_MR(port, mode); + + /* Enable interrupts */ + UART_PUT_IER(port, atmel_port->tx_done_mask); + + spin_unlock_irqrestore(&port->lock, flags); + +} + +/* + * Return TIOCSER_TEMT when transmitter FIFO and Shift register is empty. + */ +static u_int atmel_tx_empty(struct uart_port *port) +{ + return (UART_GET_CSR(port) & ATMEL_US_TXEMPTY) ? TIOCSER_TEMT : 0; +} + +/* + * Set state of the modem control output lines + */ +static void atmel_set_mctrl(struct uart_port *port, u_int mctrl) +{ + unsigned int control = 0; + unsigned int mode; + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + + if (mctrl & TIOCM_RTS) + control |= ATMEL_US_RTSEN; + else + control |= ATMEL_US_RTSDIS; + + if (mctrl & TIOCM_DTR) + control |= ATMEL_US_DTREN; + else + control |= ATMEL_US_DTRDIS; + + UART_PUT_CR(port, control); + + mctrl_gpio_set(atmel_port->gpios, mctrl); + + /* Local loopback mode? */ + mode = UART_GET_MR(port) & ~ATMEL_US_CHMODE; + if (mctrl & TIOCM_LOOP) + mode |= ATMEL_US_CHMODE_LOC_LOOP; + else + mode |= ATMEL_US_CHMODE_NORMAL; + + /* Resetting serial mode to RS232 (0x0) */ + mode &= ~ATMEL_US_USMODE; + + if (atmel_port->rs485.flags & SER_RS485_ENABLED) { + dev_dbg(port->dev, "Setting UART to RS485\n"); + if ((atmel_port->rs485.delay_rts_after_send) > 0) + UART_PUT_TTGR(port, + atmel_port->rs485.delay_rts_after_send); + mode |= ATMEL_US_USMODE_RS485; + } else { + dev_dbg(port->dev, "Setting UART to RS232\n"); + } + UART_PUT_MR(port, mode); +} + +/* + * Get state of the modem control input lines + */ +static u_int atmel_get_mctrl(struct uart_port *port) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + unsigned int ret = 0, status; + + status = UART_GET_CSR(port); + + /* + * The control signals are active low. + */ + if (!(status & ATMEL_US_DCD)) + ret |= TIOCM_CD; + if (!(status & ATMEL_US_CTS)) + ret |= TIOCM_CTS; + if (!(status & ATMEL_US_DSR)) + ret |= TIOCM_DSR; + if (!(status & ATMEL_US_RI)) + ret |= TIOCM_RI; + + return mctrl_gpio_get(atmel_port->gpios, &ret); +} + +/* + * Stop transmitting. + */ +static void atmel_stop_tx(struct uart_port *port) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + + if (atmel_use_pdc_tx(port)) { + /* disable PDC transmit */ + UART_PUT_PTCR(port, ATMEL_PDC_TXTDIS); + } + /* Disable interrupts */ + UART_PUT_IDR(port, atmel_port->tx_done_mask); + + if ((atmel_port->rs485.flags & SER_RS485_ENABLED) && + !(atmel_port->rs485.flags & SER_RS485_RX_DURING_TX)) + atmel_start_rx(port); +} + +/* + * Start transmitting. + */ +static void atmel_start_tx(struct uart_port *port) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + + if (atmel_use_pdc_tx(port)) { + if (UART_GET_PTSR(port) & ATMEL_PDC_TXTEN) + /* The transmitter is already running. Yes, we + really need this.*/ + return; + + if ((atmel_port->rs485.flags & SER_RS485_ENABLED) && + !(atmel_port->rs485.flags & SER_RS485_RX_DURING_TX)) + atmel_stop_rx(port); + + /* re-enable PDC transmit */ + UART_PUT_PTCR(port, ATMEL_PDC_TXTEN); + } + /* Enable interrupts */ + UART_PUT_IER(port, atmel_port->tx_done_mask); +} + +/* + * start receiving - port is in process of being opened. + */ +static void atmel_start_rx(struct uart_port *port) +{ + UART_PUT_CR(port, ATMEL_US_RSTSTA); /* reset status and receiver */ + + UART_PUT_CR(port, ATMEL_US_RXEN); + + if (atmel_use_pdc_rx(port)) { + /* enable PDC controller */ + UART_PUT_IER(port, ATMEL_US_ENDRX | ATMEL_US_TIMEOUT | + port->read_status_mask); + UART_PUT_PTCR(port, ATMEL_PDC_RXTEN); + } else { + UART_PUT_IER(port, ATMEL_US_RXRDY); + } +} + +/* + * Stop receiving - port is in process of being closed. + */ +static void atmel_stop_rx(struct uart_port *port) +{ + UART_PUT_CR(port, ATMEL_US_RXDIS); + + if (atmel_use_pdc_rx(port)) { + /* disable PDC receive */ + UART_PUT_PTCR(port, ATMEL_PDC_RXTDIS); + UART_PUT_IDR(port, ATMEL_US_ENDRX | ATMEL_US_TIMEOUT | + port->read_status_mask); + } else { + UART_PUT_IDR(port, ATMEL_US_RXRDY); + } +} + +/* + * Enable modem status interrupts + */ +static void atmel_enable_ms(struct uart_port *port) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + uint32_t ier = 0; + + /* + * Interrupt should not be enabled twice + */ + if (atmel_port->ms_irq_enabled) + return; + + atmel_port->ms_irq_enabled = true; + + if (atmel_port->gpio_irq[UART_GPIO_CTS] >= 0) + enable_irq(atmel_port->gpio_irq[UART_GPIO_CTS]); + else + ier |= ATMEL_US_CTSIC; + + if (atmel_port->gpio_irq[UART_GPIO_DSR] >= 0) + enable_irq(atmel_port->gpio_irq[UART_GPIO_DSR]); + else + ier |= ATMEL_US_DSRIC; + + if (atmel_port->gpio_irq[UART_GPIO_RI] >= 0) + enable_irq(atmel_port->gpio_irq[UART_GPIO_RI]); + else + ier |= ATMEL_US_RIIC; + + if (atmel_port->gpio_irq[UART_GPIO_DCD] >= 0) + enable_irq(atmel_port->gpio_irq[UART_GPIO_DCD]); + else + ier |= ATMEL_US_DCDIC; + + UART_PUT_IER(port, ier); +} + +/* + * Control the transmission of a break signal + */ +static void atmel_break_ctl(struct uart_port *port, int break_state) +{ + if (break_state != 0) + UART_PUT_CR(port, ATMEL_US_STTBRK); /* start break */ + else + UART_PUT_CR(port, ATMEL_US_STPBRK); /* stop break */ +} + +/* + * Stores the incoming character in the ring buffer + */ +static void +atmel_buffer_rx_char(struct uart_port *port, unsigned int status, + unsigned int ch) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + struct circ_buf *ring = &atmel_port->rx_ring; + struct atmel_uart_char *c; + + if (!CIRC_SPACE(ring->head, ring->tail, ATMEL_SERIAL_RINGSIZE)) + /* Buffer overflow, ignore char */ + return; + + c = &((struct atmel_uart_char *)ring->buf)[ring->head]; + c->status = status; + c->ch = ch; + + /* Make sure the character is stored before we update head. */ + smp_wmb(); + + ring->head = (ring->head + 1) & (ATMEL_SERIAL_RINGSIZE - 1); +} + +/* + * Deal with parity, framing and overrun errors. + */ +static void atmel_pdc_rxerr(struct uart_port *port, unsigned int status) +{ + /* clear error */ + UART_PUT_CR(port, ATMEL_US_RSTSTA); + + if (status & ATMEL_US_RXBRK) { + /* ignore side-effect */ + status &= ~(ATMEL_US_PARE | ATMEL_US_FRAME); + port->icount.brk++; + } + if (status & ATMEL_US_PARE) + port->icount.parity++; + if (status & ATMEL_US_FRAME) + port->icount.frame++; + if (status & ATMEL_US_OVRE) + port->icount.overrun++; +} + +/* + * Characters received (called from interrupt handler) + */ +static void atmel_rx_chars(struct uart_port *port) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + unsigned int status, ch; + + status = UART_GET_CSR(port); + while (status & ATMEL_US_RXRDY) { + ch = UART_GET_CHAR(port); + + /* + * note that the error handling code is + * out of the main execution path + */ + if (unlikely(status & (ATMEL_US_PARE | ATMEL_US_FRAME + | ATMEL_US_OVRE | ATMEL_US_RXBRK) + || atmel_port->break_active)) { + + /* clear error */ + UART_PUT_CR(port, ATMEL_US_RSTSTA); + + if (status & ATMEL_US_RXBRK + && !atmel_port->break_active) { + atmel_port->break_active = 1; + UART_PUT_IER(port, ATMEL_US_RXBRK); + } else { + /* + * This is either the end-of-break + * condition or we've received at + * least one character without RXBRK + * being set. In both cases, the next + * RXBRK will indicate start-of-break. + */ + UART_PUT_IDR(port, ATMEL_US_RXBRK); + status &= ~ATMEL_US_RXBRK; + atmel_port->break_active = 0; + } + } + + atmel_buffer_rx_char(port, status, ch); + status = UART_GET_CSR(port); + } + + tasklet_schedule(&atmel_port->tasklet); +} + +/* + * Transmit characters (called from tasklet with TXRDY interrupt + * disabled) + */ +static void atmel_tx_chars(struct uart_port *port) +{ + struct circ_buf *xmit = &port->state->xmit; + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + + if (port->x_char && UART_GET_CSR(port) & atmel_port->tx_done_mask) { + UART_PUT_CHAR(port, port->x_char); + port->icount.tx++; + port->x_char = 0; + } + if (uart_circ_empty(xmit) || uart_tx_stopped(port)) + return; + + while (UART_GET_CSR(port) & atmel_port->tx_done_mask) { + UART_PUT_CHAR(port, xmit->buf[xmit->tail]); + xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); + port->icount.tx++; + if (uart_circ_empty(xmit)) + break; + } + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(port); + + if (!uart_circ_empty(xmit)) + /* Enable interrupts */ + UART_PUT_IER(port, atmel_port->tx_done_mask); +} + +static void atmel_complete_tx_dma(void *arg) +{ + struct atmel_uart_port *atmel_port = arg; + struct uart_port *port = &atmel_port->uart; + struct circ_buf *xmit = &port->state->xmit; + struct dma_chan *chan = atmel_port->chan_tx; + unsigned long flags; + + spin_lock_irqsave(&port->lock, flags); + + if (chan) + dmaengine_terminate_all(chan); + xmit->tail += sg_dma_len(&atmel_port->sg_tx); + xmit->tail &= UART_XMIT_SIZE - 1; + + port->icount.tx += sg_dma_len(&atmel_port->sg_tx); + + spin_lock_irq(&atmel_port->lock_tx); + async_tx_ack(atmel_port->desc_tx); + atmel_port->cookie_tx = -EINVAL; + atmel_port->desc_tx = NULL; + spin_unlock_irq(&atmel_port->lock_tx); + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(port); + + /* Do we really need this? */ + if (!uart_circ_empty(xmit)) + tasklet_schedule(&atmel_port->tasklet); + + spin_unlock_irqrestore(&port->lock, flags); +} + +static void atmel_release_tx_dma(struct uart_port *port) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + struct dma_chan *chan = atmel_port->chan_tx; + + if (chan) { + dmaengine_terminate_all(chan); + dma_release_channel(chan); + dma_unmap_sg(port->dev, &atmel_port->sg_tx, 1, + DMA_MEM_TO_DEV); + } + + atmel_port->desc_tx = NULL; + atmel_port->chan_tx = NULL; + atmel_port->cookie_tx = -EINVAL; +} + +/* + * Called from tasklet with TXRDY interrupt is disabled. + */ +static void atmel_tx_dma(struct uart_port *port) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + struct circ_buf *xmit = &port->state->xmit; + struct dma_chan *chan = atmel_port->chan_tx; + struct dma_async_tx_descriptor *desc; + struct scatterlist *sg = &atmel_port->sg_tx; + + /* Make sure we have an idle channel */ + if (atmel_port->desc_tx != NULL) + return; + + if (!uart_circ_empty(xmit) && !uart_tx_stopped(port)) { + /* + * DMA is idle now. + * Port xmit buffer is already mapped, + * and it is one page... Just adjust + * offsets and lengths. Since it is a circular buffer, + * we have to transmit till the end, and then the rest. + * Take the port lock to get a + * consistent xmit buffer state. + */ + sg->offset = xmit->tail & (UART_XMIT_SIZE - 1); + sg_dma_address(sg) = (sg_dma_address(sg) & + ~(UART_XMIT_SIZE - 1)) + + sg->offset; + sg_dma_len(sg) = CIRC_CNT_TO_END(xmit->head, + xmit->tail, + UART_XMIT_SIZE); + BUG_ON(!sg_dma_len(sg)); + + desc = dmaengine_prep_slave_sg(chan, + sg, + 1, + DMA_MEM_TO_DEV, + DMA_PREP_INTERRUPT | + DMA_CTRL_ACK); + if (!desc) { + dev_err(port->dev, "Failed to send via dma!\n"); + return; + } + + dma_sync_sg_for_device(port->dev, sg, 1, DMA_MEM_TO_DEV); + + atmel_port->desc_tx = desc; + desc->callback = atmel_complete_tx_dma; + desc->callback_param = atmel_port; + atmel_port->cookie_tx = dmaengine_submit(desc); + + } else { + if (atmel_port->rs485.flags & SER_RS485_ENABLED) { + /* DMA done, stop TX, start RX for RS485 */ + atmel_start_rx(port); + } + } + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(port); +} + +static int atmel_prepare_tx_dma(struct uart_port *port) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + dma_cap_mask_t mask; + struct dma_slave_config config; + int ret, nent; + + dma_cap_zero(mask); + dma_cap_set(DMA_SLAVE, mask); + + atmel_port->chan_tx = dma_request_slave_channel(port->dev, "tx"); + if (atmel_port->chan_tx == NULL) + goto chan_err; + dev_info(port->dev, "using %s for tx DMA transfers\n", + dma_chan_name(atmel_port->chan_tx)); + + spin_lock_init(&atmel_port->lock_tx); + sg_init_table(&atmel_port->sg_tx, 1); + /* UART circular tx buffer is an aligned page. */ + BUG_ON((int)port->state->xmit.buf & ~PAGE_MASK); + sg_set_page(&atmel_port->sg_tx, + virt_to_page(port->state->xmit.buf), + UART_XMIT_SIZE, + (int)port->state->xmit.buf & ~PAGE_MASK); + nent = dma_map_sg(port->dev, + &atmel_port->sg_tx, + 1, + DMA_MEM_TO_DEV); + + if (!nent) { + dev_dbg(port->dev, "need to release resource of dma\n"); + goto chan_err; + } else { + dev_dbg(port->dev, "%s: mapped %d@%p to %x\n", __func__, + sg_dma_len(&atmel_port->sg_tx), + port->state->xmit.buf, + sg_dma_address(&atmel_port->sg_tx)); + } + + /* Configure the slave DMA */ + memset(&config, 0, sizeof(config)); + config.direction = DMA_MEM_TO_DEV; + config.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE; + config.dst_addr = port->mapbase + ATMEL_US_THR; + + ret = dmaengine_device_control(atmel_port->chan_tx, + DMA_SLAVE_CONFIG, + (unsigned long)&config); + if (ret) { + dev_err(port->dev, "DMA tx slave configuration failed\n"); + goto chan_err; + } + + return 0; + +chan_err: + dev_err(port->dev, "TX channel not available, switch to pio\n"); + atmel_port->use_dma_tx = 0; + if (atmel_port->chan_tx) + atmel_release_tx_dma(port); + return -EINVAL; +} + +static void atmel_flip_buffer_rx_dma(struct uart_port *port, + char *buf, size_t count) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + struct tty_port *tport = &port->state->port; + + dma_sync_sg_for_cpu(port->dev, + &atmel_port->sg_rx, + 1, + DMA_DEV_TO_MEM); + + tty_insert_flip_string(tport, buf, count); + + dma_sync_sg_for_device(port->dev, + &atmel_port->sg_rx, + 1, + DMA_DEV_TO_MEM); + /* + * Drop the lock here since it might end up calling + * uart_start(), which takes the lock. + */ + spin_unlock(&port->lock); + tty_flip_buffer_push(tport); + spin_lock(&port->lock); +} + +static void atmel_complete_rx_dma(void *arg) +{ + struct uart_port *port = arg; + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + + tasklet_schedule(&atmel_port->tasklet); +} + +static void atmel_release_rx_dma(struct uart_port *port) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + struct dma_chan *chan = atmel_port->chan_rx; + + if (chan) { + dmaengine_terminate_all(chan); + dma_release_channel(chan); + dma_unmap_sg(port->dev, &atmel_port->sg_rx, 1, + DMA_DEV_TO_MEM); + } + + atmel_port->desc_rx = NULL; + atmel_port->chan_rx = NULL; + atmel_port->cookie_rx = -EINVAL; +} + +static void atmel_rx_from_dma(struct uart_port *port) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + struct circ_buf *ring = &atmel_port->rx_ring; + struct dma_chan *chan = atmel_port->chan_rx; + struct dma_tx_state state; + enum dma_status dmastat; + size_t pending, count; + + + /* Reset the UART timeout early so that we don't miss one */ + UART_PUT_CR(port, ATMEL_US_STTTO); + dmastat = dmaengine_tx_status(chan, + atmel_port->cookie_rx, + &state); + /* Restart a new tasklet if DMA status is error */ + if (dmastat == DMA_ERROR) { + dev_dbg(port->dev, "Get residue error, restart tasklet\n"); + UART_PUT_IER(port, ATMEL_US_TIMEOUT); + tasklet_schedule(&atmel_port->tasklet); + return; + } + /* current transfer size should no larger than dma buffer */ + pending = sg_dma_len(&atmel_port->sg_rx) - state.residue; + BUG_ON(pending > sg_dma_len(&atmel_port->sg_rx)); + + /* + * This will take the chars we have so far, + * ring->head will record the transfer size, only new bytes come + * will insert into the framework. + */ + if (pending > ring->head) { + count = pending - ring->head; + + atmel_flip_buffer_rx_dma(port, ring->buf + ring->head, count); + + ring->head += count; + if (ring->head == sg_dma_len(&atmel_port->sg_rx)) + ring->head = 0; + + port->icount.rx += count; + } + + UART_PUT_IER(port, ATMEL_US_TIMEOUT); +} + +static int atmel_prepare_rx_dma(struct uart_port *port) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + struct dma_async_tx_descriptor *desc; + dma_cap_mask_t mask; + struct dma_slave_config config; + struct circ_buf *ring; + int ret, nent; + + ring = &atmel_port->rx_ring; + + dma_cap_zero(mask); + dma_cap_set(DMA_CYCLIC, mask); + + atmel_port->chan_rx = dma_request_slave_channel(port->dev, "rx"); + if (atmel_port->chan_rx == NULL) + goto chan_err; + dev_info(port->dev, "using %s for rx DMA transfers\n", + dma_chan_name(atmel_port->chan_rx)); + + spin_lock_init(&atmel_port->lock_rx); + sg_init_table(&atmel_port->sg_rx, 1); + /* UART circular rx buffer is an aligned page. */ + BUG_ON((int)port->state->xmit.buf & ~PAGE_MASK); + sg_set_page(&atmel_port->sg_rx, + virt_to_page(ring->buf), + ATMEL_SERIAL_RINGSIZE, + (int)ring->buf & ~PAGE_MASK); + nent = dma_map_sg(port->dev, + &atmel_port->sg_rx, + 1, + DMA_DEV_TO_MEM); + + if (!nent) { + dev_dbg(port->dev, "need to release resource of dma\n"); + goto chan_err; + } else { + dev_dbg(port->dev, "%s: mapped %d@%p to %x\n", __func__, + sg_dma_len(&atmel_port->sg_rx), + ring->buf, + sg_dma_address(&atmel_port->sg_rx)); + } + + /* Configure the slave DMA */ + memset(&config, 0, sizeof(config)); + config.direction = DMA_DEV_TO_MEM; + config.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE; + config.src_addr = port->mapbase + ATMEL_US_RHR; + + ret = dmaengine_device_control(atmel_port->chan_rx, + DMA_SLAVE_CONFIG, + (unsigned long)&config); + if (ret) { + dev_err(port->dev, "DMA rx slave configuration failed\n"); + goto chan_err; + } + /* + * Prepare a cyclic dma transfer, assign 2 descriptors, + * each one is half ring buffer size + */ + desc = dmaengine_prep_dma_cyclic(atmel_port->chan_rx, + sg_dma_address(&atmel_port->sg_rx), + sg_dma_len(&atmel_port->sg_rx), + sg_dma_len(&atmel_port->sg_rx)/2, + DMA_DEV_TO_MEM, + DMA_PREP_INTERRUPT); + desc->callback = atmel_complete_rx_dma; + desc->callback_param = port; + atmel_port->desc_rx = desc; + atmel_port->cookie_rx = dmaengine_submit(desc); + + return 0; + +chan_err: + dev_err(port->dev, "RX channel not available, switch to pio\n"); + atmel_port->use_dma_rx = 0; + if (atmel_port->chan_rx) + atmel_release_rx_dma(port); + return -EINVAL; +} + +static void atmel_uart_timer_callback(unsigned long data) +{ + struct uart_port *port = (void *)data; + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + + tasklet_schedule(&atmel_port->tasklet); + mod_timer(&atmel_port->uart_timer, jiffies + uart_poll_timeout(port)); +} + +/* + * receive interrupt handler. + */ +static void +atmel_handle_receive(struct uart_port *port, unsigned int pending) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + + if (atmel_use_pdc_rx(port)) { + /* + * PDC receive. Just schedule the tasklet and let it + * figure out the details. + * + * TODO: We're not handling error flags correctly at + * the moment. + */ + if (pending & (ATMEL_US_ENDRX | ATMEL_US_TIMEOUT)) { + UART_PUT_IDR(port, (ATMEL_US_ENDRX + | ATMEL_US_TIMEOUT)); + tasklet_schedule(&atmel_port->tasklet); + } + + if (pending & (ATMEL_US_RXBRK | ATMEL_US_OVRE | + ATMEL_US_FRAME | ATMEL_US_PARE)) + atmel_pdc_rxerr(port, pending); + } + + if (atmel_use_dma_rx(port)) { + if (pending & ATMEL_US_TIMEOUT) { + UART_PUT_IDR(port, ATMEL_US_TIMEOUT); + tasklet_schedule(&atmel_port->tasklet); + } + } + + /* Interrupt receive */ + if (pending & ATMEL_US_RXRDY) + atmel_rx_chars(port); + else if (pending & ATMEL_US_RXBRK) { + /* + * End of break detected. If it came along with a + * character, atmel_rx_chars will handle it. + */ + UART_PUT_CR(port, ATMEL_US_RSTSTA); + UART_PUT_IDR(port, ATMEL_US_RXBRK); + atmel_port->break_active = 0; + } +} + +/* + * transmit interrupt handler. (Transmit is IRQF_NODELAY safe) + */ +static void +atmel_handle_transmit(struct uart_port *port, unsigned int pending) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + + if (pending & atmel_port->tx_done_mask) { + /* Either PDC or interrupt transmission */ + UART_PUT_IDR(port, atmel_port->tx_done_mask); + tasklet_schedule(&atmel_port->tasklet); + } +} + +/* + * status flags interrupt handler. + */ +static void +atmel_handle_status(struct uart_port *port, unsigned int pending, + unsigned int status) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + + if (pending & (ATMEL_US_RIIC | ATMEL_US_DSRIC | ATMEL_US_DCDIC + | ATMEL_US_CTSIC)) { + atmel_port->irq_status = status; + tasklet_schedule(&atmel_port->tasklet); + } +} + +/* + * Interrupt handler + */ +static irqreturn_t atmel_interrupt(int irq, void *dev_id) +{ + struct uart_port *port = dev_id; + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + unsigned int status, pending, pass_counter = 0; + bool gpio_handled = false; + + do { + status = atmel_get_lines_status(port); + pending = status & UART_GET_IMR(port); + if (!gpio_handled) { + /* + * Dealing with GPIO interrupt + */ + if (irq == atmel_port->gpio_irq[UART_GPIO_CTS]) + pending |= ATMEL_US_CTSIC; + + if (irq == atmel_port->gpio_irq[UART_GPIO_DSR]) + pending |= ATMEL_US_DSRIC; + + if (irq == atmel_port->gpio_irq[UART_GPIO_RI]) + pending |= ATMEL_US_RIIC; + + if (irq == atmel_port->gpio_irq[UART_GPIO_DCD]) + pending |= ATMEL_US_DCDIC; + + gpio_handled = true; + } + if (!pending) + break; + + atmel_handle_receive(port, pending); + atmel_handle_status(port, pending, status); + atmel_handle_transmit(port, pending); + } while (pass_counter++ < ATMEL_ISR_PASS_LIMIT); + + return pass_counter ? IRQ_HANDLED : IRQ_NONE; +} + +static void atmel_release_tx_pdc(struct uart_port *port) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx; + + dma_unmap_single(port->dev, + pdc->dma_addr, + pdc->dma_size, + DMA_TO_DEVICE); +} + +/* + * Called from tasklet with ENDTX and TXBUFE interrupts disabled. + */ +static void atmel_tx_pdc(struct uart_port *port) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + struct circ_buf *xmit = &port->state->xmit; + struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx; + int count; + + /* nothing left to transmit? */ + if (UART_GET_TCR(port)) + return; + + xmit->tail += pdc->ofs; + xmit->tail &= UART_XMIT_SIZE - 1; + + port->icount.tx += pdc->ofs; + pdc->ofs = 0; + + /* more to transmit - setup next transfer */ + + /* disable PDC transmit */ + UART_PUT_PTCR(port, ATMEL_PDC_TXTDIS); + + if (!uart_circ_empty(xmit) && !uart_tx_stopped(port)) { + dma_sync_single_for_device(port->dev, + pdc->dma_addr, + pdc->dma_size, + DMA_TO_DEVICE); + + count = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE); + pdc->ofs = count; + + UART_PUT_TPR(port, pdc->dma_addr + xmit->tail); + UART_PUT_TCR(port, count); + /* re-enable PDC transmit */ + UART_PUT_PTCR(port, ATMEL_PDC_TXTEN); + /* Enable interrupts */ + UART_PUT_IER(port, atmel_port->tx_done_mask); + } else { + if ((atmel_port->rs485.flags & SER_RS485_ENABLED) && + !(atmel_port->rs485.flags & SER_RS485_RX_DURING_TX)) { + /* DMA done, stop TX, start RX for RS485 */ + atmel_start_rx(port); + } + } + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(port); +} + +static int atmel_prepare_tx_pdc(struct uart_port *port) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx; + struct circ_buf *xmit = &port->state->xmit; + + pdc->buf = xmit->buf; + pdc->dma_addr = dma_map_single(port->dev, + pdc->buf, + UART_XMIT_SIZE, + DMA_TO_DEVICE); + pdc->dma_size = UART_XMIT_SIZE; + pdc->ofs = 0; + + return 0; +} + +static void atmel_rx_from_ring(struct uart_port *port) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + struct circ_buf *ring = &atmel_port->rx_ring; + unsigned int flg; + unsigned int status; + + while (ring->head != ring->tail) { + struct atmel_uart_char c; + + /* Make sure c is loaded after head. */ + smp_rmb(); + + c = ((struct atmel_uart_char *)ring->buf)[ring->tail]; + + ring->tail = (ring->tail + 1) & (ATMEL_SERIAL_RINGSIZE - 1); + + port->icount.rx++; + status = c.status; + flg = TTY_NORMAL; + + /* + * note that the error handling code is + * out of the main execution path + */ + if (unlikely(status & (ATMEL_US_PARE | ATMEL_US_FRAME + | ATMEL_US_OVRE | ATMEL_US_RXBRK))) { + if (status & ATMEL_US_RXBRK) { + /* ignore side-effect */ + status &= ~(ATMEL_US_PARE | ATMEL_US_FRAME); + + port->icount.brk++; + if (uart_handle_break(port)) + continue; + } + if (status & ATMEL_US_PARE) + port->icount.parity++; + if (status & ATMEL_US_FRAME) + port->icount.frame++; + if (status & ATMEL_US_OVRE) + port->icount.overrun++; + + status &= port->read_status_mask; + + if (status & ATMEL_US_RXBRK) + flg = TTY_BREAK; + else if (status & ATMEL_US_PARE) + flg = TTY_PARITY; + else if (status & ATMEL_US_FRAME) + flg = TTY_FRAME; + } + + + if (uart_handle_sysrq_char(port, c.ch)) + continue; + + uart_insert_char(port, status, ATMEL_US_OVRE, c.ch, flg); + } + + /* + * Drop the lock here since it might end up calling + * uart_start(), which takes the lock. + */ + spin_unlock(&port->lock); + tty_flip_buffer_push(&port->state->port); + spin_lock(&port->lock); +} + +static void atmel_release_rx_pdc(struct uart_port *port) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + int i; + + for (i = 0; i < 2; i++) { + struct atmel_dma_buffer *pdc = &atmel_port->pdc_rx[i]; + + dma_unmap_single(port->dev, + pdc->dma_addr, + pdc->dma_size, + DMA_FROM_DEVICE); + kfree(pdc->buf); + } +} + +static void atmel_rx_from_pdc(struct uart_port *port) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + struct tty_port *tport = &port->state->port; + struct atmel_dma_buffer *pdc; + int rx_idx = atmel_port->pdc_rx_idx; + unsigned int head; + unsigned int tail; + unsigned int count; + + do { + /* Reset the UART timeout early so that we don't miss one */ + UART_PUT_CR(port, ATMEL_US_STTTO); + + pdc = &atmel_port->pdc_rx[rx_idx]; + head = UART_GET_RPR(port) - pdc->dma_addr; + tail = pdc->ofs; + + /* If the PDC has switched buffers, RPR won't contain + * any address within the current buffer. Since head + * is unsigned, we just need a one-way comparison to + * find out. + * + * In this case, we just need to consume the entire + * buffer and resubmit it for DMA. This will clear the + * ENDRX bit as well, so that we can safely re-enable + * all interrupts below. + */ + head = min(head, pdc->dma_size); + + if (likely(head != tail)) { + dma_sync_single_for_cpu(port->dev, pdc->dma_addr, + pdc->dma_size, DMA_FROM_DEVICE); + + /* + * head will only wrap around when we recycle + * the DMA buffer, and when that happens, we + * explicitly set tail to 0. So head will + * always be greater than tail. + */ + count = head - tail; + + tty_insert_flip_string(tport, pdc->buf + pdc->ofs, + count); + + dma_sync_single_for_device(port->dev, pdc->dma_addr, + pdc->dma_size, DMA_FROM_DEVICE); + + port->icount.rx += count; + pdc->ofs = head; + } + + /* + * If the current buffer is full, we need to check if + * the next one contains any additional data. + */ + if (head >= pdc->dma_size) { + pdc->ofs = 0; + UART_PUT_RNPR(port, pdc->dma_addr); + UART_PUT_RNCR(port, pdc->dma_size); + + rx_idx = !rx_idx; + atmel_port->pdc_rx_idx = rx_idx; + } + } while (head >= pdc->dma_size); + + /* + * Drop the lock here since it might end up calling + * uart_start(), which takes the lock. + */ + spin_unlock(&port->lock); + tty_flip_buffer_push(tport); + spin_lock(&port->lock); + + UART_PUT_IER(port, ATMEL_US_ENDRX | ATMEL_US_TIMEOUT); +} + +static int atmel_prepare_rx_pdc(struct uart_port *port) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + int i; + + for (i = 0; i < 2; i++) { + struct atmel_dma_buffer *pdc = &atmel_port->pdc_rx[i]; + + pdc->buf = kmalloc(PDC_BUFFER_SIZE, GFP_KERNEL); + if (pdc->buf == NULL) { + if (i != 0) { + dma_unmap_single(port->dev, + atmel_port->pdc_rx[0].dma_addr, + PDC_BUFFER_SIZE, + DMA_FROM_DEVICE); + kfree(atmel_port->pdc_rx[0].buf); + } + atmel_port->use_pdc_rx = 0; + return -ENOMEM; + } + pdc->dma_addr = dma_map_single(port->dev, + pdc->buf, + PDC_BUFFER_SIZE, + DMA_FROM_DEVICE); + pdc->dma_size = PDC_BUFFER_SIZE; + pdc->ofs = 0; + } + + atmel_port->pdc_rx_idx = 0; + + UART_PUT_RPR(port, atmel_port->pdc_rx[0].dma_addr); + UART_PUT_RCR(port, PDC_BUFFER_SIZE); + + UART_PUT_RNPR(port, atmel_port->pdc_rx[1].dma_addr); + UART_PUT_RNCR(port, PDC_BUFFER_SIZE); + + return 0; +} + +/* + * tasklet handling tty stuff outside the interrupt handler. + */ +static void atmel_tasklet_func(unsigned long data) +{ + struct uart_port *port = (struct uart_port *)data; + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + unsigned int status; + unsigned int status_change; + + /* The interrupt handler does not take the lock */ + spin_lock(&port->lock); + + atmel_port->schedule_tx(port); + + status = atmel_port->irq_status; + status_change = status ^ atmel_port->irq_status_prev; + + if (status_change & (ATMEL_US_RI | ATMEL_US_DSR + | ATMEL_US_DCD | ATMEL_US_CTS)) { + /* TODO: All reads to CSR will clear these interrupts! */ + if (status_change & ATMEL_US_RI) + port->icount.rng++; + if (status_change & ATMEL_US_DSR) + port->icount.dsr++; + if (status_change & ATMEL_US_DCD) + uart_handle_dcd_change(port, !(status & ATMEL_US_DCD)); + if (status_change & ATMEL_US_CTS) + uart_handle_cts_change(port, !(status & ATMEL_US_CTS)); + + wake_up_interruptible(&port->state->port.delta_msr_wait); + + atmel_port->irq_status_prev = status; + } + + atmel_port->schedule_rx(port); + + spin_unlock(&port->lock); +} + +static int atmel_init_property(struct atmel_uart_port *atmel_port, + struct platform_device *pdev) +{ + struct device_node *np = pdev->dev.of_node; + struct atmel_uart_data *pdata = dev_get_platdata(&pdev->dev); + + if (np) { + /* DMA/PDC usage specification */ + if (of_get_property(np, "atmel,use-dma-rx", NULL)) { + if (of_get_property(np, "dmas", NULL)) { + atmel_port->use_dma_rx = true; + atmel_port->use_pdc_rx = false; + } else { + atmel_port->use_dma_rx = false; + atmel_port->use_pdc_rx = true; + } + } else { + atmel_port->use_dma_rx = false; + atmel_port->use_pdc_rx = false; + } + + if (of_get_property(np, "atmel,use-dma-tx", NULL)) { + if (of_get_property(np, "dmas", NULL)) { + atmel_port->use_dma_tx = true; + atmel_port->use_pdc_tx = false; + } else { + atmel_port->use_dma_tx = false; + atmel_port->use_pdc_tx = true; + } + } else { + atmel_port->use_dma_tx = false; + atmel_port->use_pdc_tx = false; + } + + } else { + atmel_port->use_pdc_rx = pdata->use_dma_rx; + atmel_port->use_pdc_tx = pdata->use_dma_tx; + atmel_port->use_dma_rx = false; + atmel_port->use_dma_tx = false; + } + + return 0; +} + +static void atmel_init_rs485(struct atmel_uart_port *atmel_port, + struct platform_device *pdev) +{ + struct device_node *np = pdev->dev.of_node; + struct atmel_uart_data *pdata = dev_get_platdata(&pdev->dev); + + if (np) { + u32 rs485_delay[2]; + /* rs485 properties */ + if (of_property_read_u32_array(np, "rs485-rts-delay", + rs485_delay, 2) == 0) { + struct serial_rs485 *rs485conf = &atmel_port->rs485; + + rs485conf->delay_rts_before_send = rs485_delay[0]; + rs485conf->delay_rts_after_send = rs485_delay[1]; + rs485conf->flags = 0; + + if (of_get_property(np, "rs485-rx-during-tx", NULL)) + rs485conf->flags |= SER_RS485_RX_DURING_TX; + + if (of_get_property(np, "linux,rs485-enabled-at-boot-time", + NULL)) + rs485conf->flags |= SER_RS485_ENABLED; + } + } else { + atmel_port->rs485 = pdata->rs485; + } + +} + +static void atmel_set_ops(struct uart_port *port) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + + if (atmel_use_dma_rx(port)) { + atmel_port->prepare_rx = &atmel_prepare_rx_dma; + atmel_port->schedule_rx = &atmel_rx_from_dma; + atmel_port->release_rx = &atmel_release_rx_dma; + } else if (atmel_use_pdc_rx(port)) { + atmel_port->prepare_rx = &atmel_prepare_rx_pdc; + atmel_port->schedule_rx = &atmel_rx_from_pdc; + atmel_port->release_rx = &atmel_release_rx_pdc; + } else { + atmel_port->prepare_rx = NULL; + atmel_port->schedule_rx = &atmel_rx_from_ring; + atmel_port->release_rx = NULL; + } + + if (atmel_use_dma_tx(port)) { + atmel_port->prepare_tx = &atmel_prepare_tx_dma; + atmel_port->schedule_tx = &atmel_tx_dma; + atmel_port->release_tx = &atmel_release_tx_dma; + } else if (atmel_use_pdc_tx(port)) { + atmel_port->prepare_tx = &atmel_prepare_tx_pdc; + atmel_port->schedule_tx = &atmel_tx_pdc; + atmel_port->release_tx = &atmel_release_tx_pdc; + } else { + atmel_port->prepare_tx = NULL; + atmel_port->schedule_tx = &atmel_tx_chars; + atmel_port->release_tx = NULL; + } +} + +/* + * Get ip name usart or uart + */ +static void atmel_get_ip_name(struct uart_port *port) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + int name = UART_GET_IP_NAME(port); + u32 version; + int usart, uart; + /* usart and uart ascii */ + usart = 0x55534152; + uart = 0x44424755; + + atmel_port->is_usart = false; + + if (name == usart) { + dev_dbg(port->dev, "This is usart\n"); + atmel_port->is_usart = true; + } else if (name == uart) { + dev_dbg(port->dev, "This is uart\n"); + atmel_port->is_usart = false; + } else { + /* fallback for older SoCs: use version field */ + version = UART_GET_IP_VERSION(port); + switch (version) { + case 0x302: + case 0x10213: + dev_dbg(port->dev, "This version is usart\n"); + atmel_port->is_usart = true; + break; + case 0x203: + case 0x10202: + dev_dbg(port->dev, "This version is uart\n"); + atmel_port->is_usart = false; + break; + default: + dev_err(port->dev, "Not supported ip name nor version, set to uart\n"); + } + } +} + +static void atmel_free_gpio_irq(struct uart_port *port) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + enum mctrl_gpio_idx i; + + for (i = 0; i < UART_GPIO_MAX; i++) + if (atmel_port->gpio_irq[i] >= 0) + free_irq(atmel_port->gpio_irq[i], port); +} + +static int atmel_request_gpio_irq(struct uart_port *port) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + int *irq = atmel_port->gpio_irq; + enum mctrl_gpio_idx i; + int err = 0; + + for (i = 0; (i < UART_GPIO_MAX) && !err; i++) { + if (irq[i] < 0) + continue; + + irq_set_status_flags(irq[i], IRQ_NOAUTOEN); + err = request_irq(irq[i], atmel_interrupt, IRQ_TYPE_EDGE_BOTH, + "atmel_serial", port); + if (err) + dev_err(port->dev, "atmel_startup - Can't get %d irq\n", + irq[i]); + } + + /* + * If something went wrong, rollback. + */ + while (err && (--i >= 0)) + if (irq[i] >= 0) + free_irq(irq[i], port); + + return err; +} + +/* + * Perform initialization and enable port for reception + */ +static int atmel_startup(struct uart_port *port) +{ + struct platform_device *pdev = to_platform_device(port->dev); + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + struct tty_struct *tty = port->state->port.tty; + int retval; + + /* + * Ensure that no interrupts are enabled otherwise when + * request_irq() is called we could get stuck trying to + * handle an unexpected interrupt + */ + UART_PUT_IDR(port, -1); + atmel_port->ms_irq_enabled = false; + + /* + * Allocate the IRQ + */ + retval = request_irq(port->irq, atmel_interrupt, IRQF_SHARED, + tty ? tty->name : "atmel_serial", port); + if (retval) { + dev_err(port->dev, "atmel_startup - Can't get irq\n"); + return retval; + } + + /* + * Get the GPIO lines IRQ + */ + retval = atmel_request_gpio_irq(port); + if (retval) + goto free_irq; + + /* + * Initialize DMA (if necessary) + */ + atmel_init_property(atmel_port, pdev); + + if (atmel_port->prepare_rx) { + retval = atmel_port->prepare_rx(port); + if (retval < 0) + atmel_set_ops(port); + } + + if (atmel_port->prepare_tx) { + retval = atmel_port->prepare_tx(port); + if (retval < 0) + atmel_set_ops(port); + } + + /* Save current CSR for comparison in atmel_tasklet_func() */ + atmel_port->irq_status_prev = atmel_get_lines_status(port); + atmel_port->irq_status = atmel_port->irq_status_prev; + + /* + * Finally, enable the serial port + */ + UART_PUT_CR(port, ATMEL_US_RSTSTA | ATMEL_US_RSTRX); + /* enable xmit & rcvr */ + UART_PUT_CR(port, ATMEL_US_TXEN | ATMEL_US_RXEN); + + setup_timer(&atmel_port->uart_timer, + atmel_uart_timer_callback, + (unsigned long)port); + + if (atmel_use_pdc_rx(port)) { + /* set UART timeout */ + if (!atmel_port->is_usart) { + mod_timer(&atmel_port->uart_timer, + jiffies + uart_poll_timeout(port)); + /* set USART timeout */ + } else { + UART_PUT_RTOR(port, PDC_RX_TIMEOUT); + UART_PUT_CR(port, ATMEL_US_STTTO); + + UART_PUT_IER(port, ATMEL_US_ENDRX | ATMEL_US_TIMEOUT); + } + /* enable PDC controller */ + UART_PUT_PTCR(port, ATMEL_PDC_RXTEN); + } else if (atmel_use_dma_rx(port)) { + /* set UART timeout */ + if (!atmel_port->is_usart) { + mod_timer(&atmel_port->uart_timer, + jiffies + uart_poll_timeout(port)); + /* set USART timeout */ + } else { + UART_PUT_RTOR(port, PDC_RX_TIMEOUT); + UART_PUT_CR(port, ATMEL_US_STTTO); + + UART_PUT_IER(port, ATMEL_US_TIMEOUT); + } + } else { + /* enable receive only */ + UART_PUT_IER(port, ATMEL_US_RXRDY); + } + + return 0; + +free_irq: + free_irq(port->irq, port); + + return retval; +} + +/* + * Disable the port + */ +static void atmel_shutdown(struct uart_port *port) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + + /* + * Prevent any tasklets being scheduled during + * cleanup + */ + del_timer_sync(&atmel_port->uart_timer); + + /* + * Clear out any scheduled tasklets before + * we destroy the buffers + */ + tasklet_kill(&atmel_port->tasklet); + + /* + * Ensure everything is stopped and + * disable all interrupts, port and break condition. + */ + atmel_stop_rx(port); + atmel_stop_tx(port); + + UART_PUT_CR(port, ATMEL_US_RSTSTA); + UART_PUT_IDR(port, -1); + + + /* + * Shut-down the DMA. + */ + if (atmel_port->release_rx) + atmel_port->release_rx(port); + if (atmel_port->release_tx) + atmel_port->release_tx(port); + + /* + * Reset ring buffer pointers + */ + atmel_port->rx_ring.head = 0; + atmel_port->rx_ring.tail = 0; + + /* + * Free the interrupts + */ + free_irq(port->irq, port); + atmel_free_gpio_irq(port); + + atmel_port->ms_irq_enabled = false; +} + +/* + * Flush any TX data submitted for DMA. Called when the TX circular + * buffer is reset. + */ +static void atmel_flush_buffer(struct uart_port *port) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + + if (atmel_use_pdc_tx(port)) { + UART_PUT_TCR(port, 0); + atmel_port->pdc_tx.ofs = 0; + } +} + +/* + * Power / Clock management. + */ +static void atmel_serial_pm(struct uart_port *port, unsigned int state, + unsigned int oldstate) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + + switch (state) { + case 0: + /* + * Enable the peripheral clock for this serial port. + * This is called on uart_open() or a resume event. + */ + clk_prepare_enable(atmel_port->clk); + + /* re-enable interrupts if we disabled some on suspend */ + UART_PUT_IER(port, atmel_port->backup_imr); + break; + case 3: + /* Back up the interrupt mask and disable all interrupts */ + atmel_port->backup_imr = UART_GET_IMR(port); + UART_PUT_IDR(port, -1); + + /* + * Disable the peripheral clock for this serial port. + * This is called on uart_close() or a suspend event. + */ + clk_disable_unprepare(atmel_port->clk); + break; + default: + dev_err(port->dev, "atmel_serial: unknown pm %d\n", state); + } +} + +/* + * Change the port parameters + */ +static void atmel_set_termios(struct uart_port *port, struct ktermios *termios, + struct ktermios *old) +{ + unsigned long flags; + unsigned int mode, imr, quot, baud; + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + + /* Get current mode register */ + mode = UART_GET_MR(port) & ~(ATMEL_US_USCLKS | ATMEL_US_CHRL + | ATMEL_US_NBSTOP | ATMEL_US_PAR + | ATMEL_US_USMODE); + + baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16); + quot = uart_get_divisor(port, baud); + + if (quot > 65535) { /* BRGR is 16-bit, so switch to slower clock */ + quot /= 8; + mode |= ATMEL_US_USCLKS_MCK_DIV8; + } + + /* byte size */ + switch (termios->c_cflag & CSIZE) { + case CS5: + mode |= ATMEL_US_CHRL_5; + break; + case CS6: + mode |= ATMEL_US_CHRL_6; + break; + case CS7: + mode |= ATMEL_US_CHRL_7; + break; + default: + mode |= ATMEL_US_CHRL_8; + break; + } + + /* stop bits */ + if (termios->c_cflag & CSTOPB) + mode |= ATMEL_US_NBSTOP_2; + + /* parity */ + if (termios->c_cflag & PARENB) { + /* Mark or Space parity */ + if (termios->c_cflag & CMSPAR) { + if (termios->c_cflag & PARODD) + mode |= ATMEL_US_PAR_MARK; + else + mode |= ATMEL_US_PAR_SPACE; + } else if (termios->c_cflag & PARODD) + mode |= ATMEL_US_PAR_ODD; + else + mode |= ATMEL_US_PAR_EVEN; + } else + mode |= ATMEL_US_PAR_NONE; + + /* hardware handshake (RTS/CTS) */ + if (termios->c_cflag & CRTSCTS) + mode |= ATMEL_US_USMODE_HWHS; + else + mode |= ATMEL_US_USMODE_NORMAL; + + spin_lock_irqsave(&port->lock, flags); + + port->read_status_mask = ATMEL_US_OVRE; + if (termios->c_iflag & INPCK) + port->read_status_mask |= (ATMEL_US_FRAME | ATMEL_US_PARE); + if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK)) + port->read_status_mask |= ATMEL_US_RXBRK; + + if (atmel_use_pdc_rx(port)) + /* need to enable error interrupts */ + UART_PUT_IER(port, port->read_status_mask); + + /* + * Characters to ignore + */ + port->ignore_status_mask = 0; + if (termios->c_iflag & IGNPAR) + port->ignore_status_mask |= (ATMEL_US_FRAME | ATMEL_US_PARE); + if (termios->c_iflag & IGNBRK) { + port->ignore_status_mask |= ATMEL_US_RXBRK; + /* + * If we're ignoring parity and break indicators, + * ignore overruns too (for real raw support). + */ + if (termios->c_iflag & IGNPAR) + port->ignore_status_mask |= ATMEL_US_OVRE; + } + /* TODO: Ignore all characters if CREAD is set.*/ + + /* update the per-port timeout */ + uart_update_timeout(port, termios->c_cflag, baud); + + /* + * save/disable interrupts. The tty layer will ensure that the + * transmitter is empty if requested by the caller, so there's + * no need to wait for it here. + */ + imr = UART_GET_IMR(port); + UART_PUT_IDR(port, -1); + + /* disable receiver and transmitter */ + UART_PUT_CR(port, ATMEL_US_TXDIS | ATMEL_US_RXDIS); + + /* Resetting serial mode to RS232 (0x0) */ + mode &= ~ATMEL_US_USMODE; + + if (atmel_port->rs485.flags & SER_RS485_ENABLED) { + if ((atmel_port->rs485.delay_rts_after_send) > 0) + UART_PUT_TTGR(port, + atmel_port->rs485.delay_rts_after_send); + mode |= ATMEL_US_USMODE_RS485; + } + + /* set the parity, stop bits and data size */ + UART_PUT_MR(port, mode); + + /* set the baud rate */ + UART_PUT_BRGR(port, quot); + UART_PUT_CR(port, ATMEL_US_RSTSTA | ATMEL_US_RSTRX); + UART_PUT_CR(port, ATMEL_US_TXEN | ATMEL_US_RXEN); + + /* restore interrupts */ + UART_PUT_IER(port, imr); + + /* CTS flow-control and modem-status interrupts */ + if (UART_ENABLE_MS(port, termios->c_cflag)) + port->ops->enable_ms(port); + + spin_unlock_irqrestore(&port->lock, flags); +} + +static void atmel_set_ldisc(struct uart_port *port, int new) +{ + if (new == N_PPS) { + port->flags |= UPF_HARDPPS_CD; + atmel_enable_ms(port); + } else { + port->flags &= ~UPF_HARDPPS_CD; + } +} + +/* + * Return string describing the specified port + */ +static const char *atmel_type(struct uart_port *port) +{ + return (port->type == PORT_ATMEL) ? "ATMEL_SERIAL" : NULL; +} + +/* + * Release the memory region(s) being used by 'port'. + */ +static void atmel_release_port(struct uart_port *port) +{ + struct platform_device *pdev = to_platform_device(port->dev); + int size = pdev->resource[0].end - pdev->resource[0].start + 1; + + release_mem_region(port->mapbase, size); + + if (port->flags & UPF_IOREMAP) { + iounmap(port->membase); + port->membase = NULL; + } +} + +/* + * Request the memory region(s) being used by 'port'. + */ +static int atmel_request_port(struct uart_port *port) +{ + struct platform_device *pdev = to_platform_device(port->dev); + int size = pdev->resource[0].end - pdev->resource[0].start + 1; + + if (!request_mem_region(port->mapbase, size, "atmel_serial")) + return -EBUSY; + + if (port->flags & UPF_IOREMAP) { + port->membase = ioremap(port->mapbase, size); + if (port->membase == NULL) { + release_mem_region(port->mapbase, size); + return -ENOMEM; + } + } + + return 0; +} + +/* + * Configure/autoconfigure the port. + */ +static void atmel_config_port(struct uart_port *port, int flags) +{ + if (flags & UART_CONFIG_TYPE) { + port->type = PORT_ATMEL; + atmel_request_port(port); + } +} + +/* + * Verify the new serial_struct (for TIOCSSERIAL). + */ +static int atmel_verify_port(struct uart_port *port, struct serial_struct *ser) +{ + int ret = 0; + if (ser->type != PORT_UNKNOWN && ser->type != PORT_ATMEL) + ret = -EINVAL; + if (port->irq != ser->irq) + ret = -EINVAL; + if (ser->io_type != SERIAL_IO_MEM) + ret = -EINVAL; + if (port->uartclk / 16 != ser->baud_base) + ret = -EINVAL; + if ((void *)port->mapbase != ser->iomem_base) + ret = -EINVAL; + if (port->iobase != ser->port) + ret = -EINVAL; + if (ser->hub6 != 0) + ret = -EINVAL; + return ret; +} + +#ifdef CONFIG_CONSOLE_POLL +static int atmel_poll_get_char(struct uart_port *port) +{ + while (!(UART_GET_CSR(port) & ATMEL_US_RXRDY)) + cpu_relax(); + + return UART_GET_CHAR(port); +} + +static void atmel_poll_put_char(struct uart_port *port, unsigned char ch) +{ + while (!(UART_GET_CSR(port) & ATMEL_US_TXRDY)) + cpu_relax(); + + UART_PUT_CHAR(port, ch); +} +#endif + +static int +atmel_ioctl(struct uart_port *port, unsigned int cmd, unsigned long arg) +{ + struct serial_rs485 rs485conf; + + switch (cmd) { + case TIOCSRS485: + if (copy_from_user(&rs485conf, (struct serial_rs485 *) arg, + sizeof(rs485conf))) + return -EFAULT; + + atmel_config_rs485(port, &rs485conf); + break; + + case TIOCGRS485: + if (copy_to_user((struct serial_rs485 *) arg, + &(to_atmel_uart_port(port)->rs485), + sizeof(rs485conf))) + return -EFAULT; + break; + + default: + return -ENOIOCTLCMD; + } + return 0; +} + + + +static struct uart_ops atmel_pops = { + .tx_empty = atmel_tx_empty, + .set_mctrl = atmel_set_mctrl, + .get_mctrl = atmel_get_mctrl, + .stop_tx = atmel_stop_tx, + .start_tx = atmel_start_tx, + .stop_rx = atmel_stop_rx, + .enable_ms = atmel_enable_ms, + .break_ctl = atmel_break_ctl, + .startup = atmel_startup, + .shutdown = atmel_shutdown, + .flush_buffer = atmel_flush_buffer, + .set_termios = atmel_set_termios, + .set_ldisc = atmel_set_ldisc, + .type = atmel_type, + .release_port = atmel_release_port, + .request_port = atmel_request_port, + .config_port = atmel_config_port, + .verify_port = atmel_verify_port, + .pm = atmel_serial_pm, + .ioctl = atmel_ioctl, +#ifdef CONFIG_CONSOLE_POLL + .poll_get_char = atmel_poll_get_char, + .poll_put_char = atmel_poll_put_char, +#endif +}; + +/* + * Configure the port from the platform device resource info. + */ +static int atmel_init_port(struct atmel_uart_port *atmel_port, + struct platform_device *pdev) +{ + int ret; + struct uart_port *port = &atmel_port->uart; + struct atmel_uart_data *pdata = dev_get_platdata(&pdev->dev); + + if (!atmel_init_property(atmel_port, pdev)) + atmel_set_ops(port); + + atmel_init_rs485(atmel_port, pdev); + + port->iotype = UPIO_MEM; + port->flags = UPF_BOOT_AUTOCONF; + port->ops = &atmel_pops; + port->fifosize = 1; + port->dev = &pdev->dev; + port->mapbase = pdev->resource[0].start; + port->irq = pdev->resource[1].start; + + tasklet_init(&atmel_port->tasklet, atmel_tasklet_func, + (unsigned long)port); + + memset(&atmel_port->rx_ring, 0, sizeof(atmel_port->rx_ring)); + + if (pdata && pdata->regs) { + /* Already mapped by setup code */ + port->membase = pdata->regs; + } else { + port->flags |= UPF_IOREMAP; + port->membase = NULL; + } + + /* for console, the clock could already be configured */ + if (!atmel_port->clk) { + atmel_port->clk = clk_get(&pdev->dev, "usart"); + if (IS_ERR(atmel_port->clk)) { + ret = PTR_ERR(atmel_port->clk); + atmel_port->clk = NULL; + return ret; + } + ret = clk_prepare_enable(atmel_port->clk); + if (ret) { + clk_put(atmel_port->clk); + atmel_port->clk = NULL; + return ret; + } + port->uartclk = clk_get_rate(atmel_port->clk); + clk_disable_unprepare(atmel_port->clk); + /* only enable clock when USART is in use */ + } + + /* Use TXEMPTY for interrupt when rs485 else TXRDY or ENDTX|TXBUFE */ + if (atmel_port->rs485.flags & SER_RS485_ENABLED) + atmel_port->tx_done_mask = ATMEL_US_TXEMPTY; + else if (atmel_use_pdc_tx(port)) { + port->fifosize = PDC_BUFFER_SIZE; + atmel_port->tx_done_mask = ATMEL_US_ENDTX | ATMEL_US_TXBUFE; + } else { + atmel_port->tx_done_mask = ATMEL_US_TXRDY; + } + + return 0; +} + +struct platform_device *atmel_default_console_device; /* the serial console device */ + +#ifdef CONFIG_SERIAL_ATMEL_CONSOLE +static void atmel_console_putchar(struct uart_port *port, int ch) +{ + while (!(UART_GET_CSR(port) & ATMEL_US_TXRDY)) + cpu_relax(); + UART_PUT_CHAR(port, ch); +} + +/* + * Interrupts are disabled on entering + */ +static void atmel_console_write(struct console *co, const char *s, u_int count) +{ + struct uart_port *port = &atmel_ports[co->index].uart; + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + unsigned int status, imr; + unsigned int pdc_tx; + + /* + * First, save IMR and then disable interrupts + */ + imr = UART_GET_IMR(port); + UART_PUT_IDR(port, ATMEL_US_RXRDY | atmel_port->tx_done_mask); + + /* Store PDC transmit status and disable it */ + pdc_tx = UART_GET_PTSR(port) & ATMEL_PDC_TXTEN; + UART_PUT_PTCR(port, ATMEL_PDC_TXTDIS); + + uart_console_write(port, s, count, atmel_console_putchar); + + /* + * Finally, wait for transmitter to become empty + * and restore IMR + */ + do { + status = UART_GET_CSR(port); + } while (!(status & ATMEL_US_TXRDY)); + + /* Restore PDC transmit status */ + if (pdc_tx) + UART_PUT_PTCR(port, ATMEL_PDC_TXTEN); + + /* set interrupts back the way they were */ + UART_PUT_IER(port, imr); +} + +/* + * If the port was already initialised (eg, by a boot loader), + * try to determine the current setup. + */ +static void __init atmel_console_get_options(struct uart_port *port, int *baud, + int *parity, int *bits) +{ + unsigned int mr, quot; + + /* + * If the baud rate generator isn't running, the port wasn't + * initialized by the boot loader. + */ + quot = UART_GET_BRGR(port) & ATMEL_US_CD; + if (!quot) + return; + + mr = UART_GET_MR(port) & ATMEL_US_CHRL; + if (mr == ATMEL_US_CHRL_8) + *bits = 8; + else + *bits = 7; + + mr = UART_GET_MR(port) & ATMEL_US_PAR; + if (mr == ATMEL_US_PAR_EVEN) + *parity = 'e'; + else if (mr == ATMEL_US_PAR_ODD) + *parity = 'o'; + + /* + * The serial core only rounds down when matching this to a + * supported baud rate. Make sure we don't end up slightly + * lower than one of those, as it would make us fall through + * to a much lower baud rate than we really want. + */ + *baud = port->uartclk / (16 * (quot - 1)); +} + +static int __init atmel_console_setup(struct console *co, char *options) +{ + int ret; + struct uart_port *port = &atmel_ports[co->index].uart; + int baud = 115200; + int bits = 8; + int parity = 'n'; + int flow = 'n'; + + if (port->membase == NULL) { + /* Port not initialized yet - delay setup */ + return -ENODEV; + } + + ret = clk_prepare_enable(atmel_ports[co->index].clk); + if (ret) + return ret; + + UART_PUT_IDR(port, -1); + UART_PUT_CR(port, ATMEL_US_RSTSTA | ATMEL_US_RSTRX); + UART_PUT_CR(port, ATMEL_US_TXEN | ATMEL_US_RXEN); + + if (options) + uart_parse_options(options, &baud, &parity, &bits, &flow); + else + atmel_console_get_options(port, &baud, &parity, &bits); + + return uart_set_options(port, co, baud, parity, bits, flow); +} + +static struct uart_driver atmel_uart; + +static struct console atmel_console = { + .name = ATMEL_DEVICENAME, + .write = atmel_console_write, + .device = uart_console_device, + .setup = atmel_console_setup, + .flags = CON_PRINTBUFFER, + .index = -1, + .data = &atmel_uart, +}; + +#define ATMEL_CONSOLE_DEVICE (&atmel_console) + +/* + * Early console initialization (before VM subsystem initialized). + */ +static int __init atmel_console_init(void) +{ + int ret; + if (atmel_default_console_device) { + struct atmel_uart_data *pdata = + dev_get_platdata(&atmel_default_console_device->dev); + int id = pdata->num; + struct atmel_uart_port *port = &atmel_ports[id]; + + port->backup_imr = 0; + port->uart.line = id; + + add_preferred_console(ATMEL_DEVICENAME, id, NULL); + ret = atmel_init_port(port, atmel_default_console_device); + if (ret) + return ret; + register_console(&atmel_console); + } + + return 0; +} + +console_initcall(atmel_console_init); + +/* + * Late console initialization. + */ +static int __init atmel_late_console_init(void) +{ + if (atmel_default_console_device + && !(atmel_console.flags & CON_ENABLED)) + register_console(&atmel_console); + + return 0; +} + +core_initcall(atmel_late_console_init); + +static inline bool atmel_is_console_port(struct uart_port *port) +{ + return port->cons && port->cons->index == port->line; +} + +#else +#define ATMEL_CONSOLE_DEVICE NULL + +static inline bool atmel_is_console_port(struct uart_port *port) +{ + return false; +} +#endif + +static struct uart_driver atmel_uart = { + .owner = THIS_MODULE, + .driver_name = "atmel_serial", + .dev_name = ATMEL_DEVICENAME, + .major = SERIAL_ATMEL_MAJOR, + .minor = MINOR_START, + .nr = ATMEL_MAX_UART, + .cons = ATMEL_CONSOLE_DEVICE, +}; + +#ifdef CONFIG_PM +static bool atmel_serial_clk_will_stop(void) +{ +#ifdef CONFIG_ARCH_AT91 + return at91_suspend_entering_slow_clock(); +#else + return false; +#endif +} + +static int atmel_serial_suspend(struct platform_device *pdev, + pm_message_t state) +{ + struct uart_port *port = platform_get_drvdata(pdev); + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + + if (atmel_is_console_port(port) && console_suspend_enabled) { + /* Drain the TX shifter */ + while (!(UART_GET_CSR(port) & ATMEL_US_TXEMPTY)) + cpu_relax(); + } + + /* we can not wake up if we're running on slow clock */ + atmel_port->may_wakeup = device_may_wakeup(&pdev->dev); + if (atmel_serial_clk_will_stop()) + device_set_wakeup_enable(&pdev->dev, 0); + + uart_suspend_port(&atmel_uart, port); + + return 0; +} + +static int atmel_serial_resume(struct platform_device *pdev) +{ + struct uart_port *port = platform_get_drvdata(pdev); + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + + uart_resume_port(&atmel_uart, port); + device_set_wakeup_enable(&pdev->dev, atmel_port->may_wakeup); + + return 0; +} +#else +#define atmel_serial_suspend NULL +#define atmel_serial_resume NULL +#endif + +static int atmel_init_gpios(struct atmel_uart_port *p, struct device *dev) +{ + enum mctrl_gpio_idx i; + struct gpio_desc *gpiod; + + p->gpios = mctrl_gpio_init(dev, 0); + if (IS_ERR_OR_NULL(p->gpios)) + return -1; + + for (i = 0; i < UART_GPIO_MAX; i++) { + gpiod = mctrl_gpio_to_gpiod(p->gpios, i); + if (gpiod && (gpiod_get_direction(gpiod) == GPIOF_DIR_IN)) + p->gpio_irq[i] = gpiod_to_irq(gpiod); + else + p->gpio_irq[i] = -EINVAL; + } + + return 0; +} + +static int atmel_serial_probe(struct platform_device *pdev) +{ + struct atmel_uart_port *port; + struct device_node *np = pdev->dev.of_node; + struct atmel_uart_data *pdata = dev_get_platdata(&pdev->dev); + void *data; + int ret = -ENODEV; + + BUILD_BUG_ON(ATMEL_SERIAL_RINGSIZE & (ATMEL_SERIAL_RINGSIZE - 1)); + + if (np) + ret = of_alias_get_id(np, "serial"); + else + if (pdata) + ret = pdata->num; + + if (ret < 0) + /* port id not found in platform data nor device-tree aliases: + * auto-enumerate it */ + ret = find_first_zero_bit(atmel_ports_in_use, ATMEL_MAX_UART); + + if (ret >= ATMEL_MAX_UART) { + ret = -ENODEV; + goto err; + } + + if (test_and_set_bit(ret, atmel_ports_in_use)) { + /* port already in use */ + ret = -EBUSY; + goto err; + } + + port = &atmel_ports[ret]; + port->backup_imr = 0; + port->uart.line = ret; + + ret = atmel_init_gpios(port, &pdev->dev); + if (ret < 0) + dev_err(&pdev->dev, "%s", + "Failed to initialize GPIOs. The serial port may not work as expected"); + + ret = atmel_init_port(port, pdev); + if (ret) + goto err; + + if (!atmel_use_pdc_rx(&port->uart)) { + ret = -ENOMEM; + data = kmalloc(sizeof(struct atmel_uart_char) + * ATMEL_SERIAL_RINGSIZE, GFP_KERNEL); + if (!data) + goto err_alloc_ring; + port->rx_ring.buf = data; + } + + ret = uart_add_one_port(&atmel_uart, &port->uart); + if (ret) + goto err_add_port; + +#ifdef CONFIG_SERIAL_ATMEL_CONSOLE + if (atmel_is_console_port(&port->uart) + && ATMEL_CONSOLE_DEVICE->flags & CON_ENABLED) { + /* + * The serial core enabled the clock for us, so undo + * the clk_prepare_enable() in atmel_console_setup() + */ + clk_disable_unprepare(port->clk); + } +#endif + + device_init_wakeup(&pdev->dev, 1); + platform_set_drvdata(pdev, port); + + if (port->rs485.flags & SER_RS485_ENABLED) { + UART_PUT_MR(&port->uart, ATMEL_US_USMODE_NORMAL); + UART_PUT_CR(&port->uart, ATMEL_US_RTSEN); + } + + /* + * Get port name of usart or uart + */ + atmel_get_ip_name(&port->uart); + + return 0; + +err_add_port: + kfree(port->rx_ring.buf); + port->rx_ring.buf = NULL; +err_alloc_ring: + if (!atmel_is_console_port(&port->uart)) { + clk_put(port->clk); + port->clk = NULL; + } +err: + return ret; +} + +static int atmel_serial_remove(struct platform_device *pdev) +{ + struct uart_port *port = platform_get_drvdata(pdev); + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + int ret = 0; + + tasklet_kill(&atmel_port->tasklet); + + device_init_wakeup(&pdev->dev, 0); + + ret = uart_remove_one_port(&atmel_uart, port); + + kfree(atmel_port->rx_ring.buf); + + /* "port" is allocated statically, so we shouldn't free it */ + + clear_bit(port->line, atmel_ports_in_use); + + clk_put(atmel_port->clk); + + return ret; +} + +static struct platform_driver atmel_serial_driver = { + .probe = atmel_serial_probe, + .remove = atmel_serial_remove, + .suspend = atmel_serial_suspend, + .resume = atmel_serial_resume, + .driver = { + .name = "atmel_usart", + .owner = THIS_MODULE, + .of_match_table = of_match_ptr(atmel_serial_dt_ids), + }, +}; + +static int __init atmel_serial_init(void) +{ + int ret; + + ret = uart_register_driver(&atmel_uart); + if (ret) + return ret; + + ret = platform_driver_register(&atmel_serial_driver); + if (ret) + uart_unregister_driver(&atmel_uart); + + return ret; +} + +static void __exit atmel_serial_exit(void) +{ + platform_driver_unregister(&atmel_serial_driver); + uart_unregister_driver(&atmel_uart); +} + +module_init(atmel_serial_init); +module_exit(atmel_serial_exit); + +MODULE_AUTHOR("Rick Bronson"); +MODULE_DESCRIPTION("Atmel AT91 / AT32 serial port driver"); +MODULE_LICENSE("GPL"); +MODULE_ALIAS("platform:atmel_usart"); |