diff options
Diffstat (limited to 'drivers/spi/Kconfig')
| -rw-r--r-- | drivers/spi/Kconfig | 213 |
1 files changed, 164 insertions, 49 deletions
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig index 2e188e1127e..213b5cbb9dc 100644 --- a/drivers/spi/Kconfig +++ b/drivers/spi/Kconfig @@ -61,7 +61,7 @@ config SPI_ALTERA config SPI_ATH79 tristate "Atheros AR71XX/AR724X/AR913X SPI controller driver" - depends on ATH79 && GENERIC_GPIO + depends on ATH79 && GPIOLIB select SPI_BITBANG help This enables support for the SPI controller present on the @@ -69,17 +69,35 @@ config SPI_ATH79 config SPI_ATMEL tristate "Atmel SPI Controller" - depends on (ARCH_AT91 || AVR32) + depends on (ARCH_AT91 || AVR32 || COMPILE_TEST) help This selects a driver for the Atmel SPI Controller, present on many AT32 (AVR32) and AT91 (ARM) chips. +config SPI_BCM2835 + tristate "BCM2835 SPI controller" + depends on ARCH_BCM2835 || COMPILE_TEST + help + This selects a driver for the Broadcom BCM2835 SPI master. + + The BCM2835 contains two types of SPI master controller; the + "universal SPI master", and the regular SPI controller. This driver + is for the regular SPI controller. Slave mode operation is not also + not supported. + config SPI_BFIN5XX tristate "SPI controller driver for ADI Blackfin5xx" - depends on BLACKFIN + depends on BLACKFIN && !BF60x help This is the SPI controller master driver for Blackfin 5xx processor. +config SPI_ADI_V3 + tristate "SPI controller v3 for ADI" + depends on BF60x + help + This is the SPI controller v3 master driver + found on Blackfin 60x processor. + config SPI_BFIN_SPORT tristate "SPI bus via Blackfin SPORT" depends on BLACKFIN @@ -88,7 +106,7 @@ config SPI_BFIN_SPORT config SPI_AU1550 tristate "Au1550/Au1200/Au1300 SPI Controller" - depends on MIPS_ALCHEMY && EXPERIMENTAL + depends on MIPS_ALCHEMY select SPI_BITBANG help If you say yes to this option, support will be included for the @@ -100,6 +118,13 @@ config SPI_BCM63XX help Enable support for the SPI controller on the Broadcom BCM63xx SoCs. +config SPI_BCM63XX_HSSPI + tristate "Broadcom BCM63XX HS SPI controller driver" + depends on BCM63XX || COMPILE_TEST + help + This enables support for the High Speed SPI controller present on + newer Broadcom BCM63XX SoCs. + config SPI_BITBANG tristate "Utilities for Bitbanging SPI masters" help @@ -123,9 +148,16 @@ config SPI_BUTTERFLY inexpensive battery powered microcontroller evaluation board. This same cable can be used to flash new firmware. +config SPI_CADENCE + tristate "Cadence SPI controller" + depends on ARM + help + This selects the Cadence SPI controller master driver + used by Xilinx Zynq. + config SPI_CLPS711X tristate "CLPS711X host SPI controller" - depends on ARCH_CLPS711X + depends on ARCH_CLPS711X || COMPILE_TEST help This enables dedicated general purpose SPI/Microwire1-compatible master mode interface (SSI1) for CLPS711X-based CPUs. @@ -139,15 +171,21 @@ config SPI_COLDFIRE_QSPI config SPI_DAVINCI tristate "Texas Instruments DaVinci/DA8x/OMAP-L/AM1x SoC SPI controller" - depends on ARCH_DAVINCI + depends on ARCH_DAVINCI || ARCH_KEYSTONE select SPI_BITBANG - select TI_EDMA help SPI master controller for DaVinci/DA8x/OMAP-L/AM1x SPI modules. +config SPI_EFM32 + tristate "EFM32 SPI controller" + depends on OF && ARM && (ARCH_EFM32 || COMPILE_TEST) + select SPI_BITBANG + help + Driver for the spi controller found on Energy Micro's EFM32 SoCs. + config SPI_EP93XX tristate "Cirrus Logic EP93xx SPI controller" - depends on ARCH_EP93XX + depends on ARCH_EP93XX || COMPILE_TEST help This enables using the Cirrus EP93xx SPI controller in master mode. @@ -163,7 +201,7 @@ config SPI_FALCON config SPI_GPIO tristate "GPIO-based bitbanging SPI Master" - depends on GENERIC_GPIO + depends on GPIOLIB select SPI_BITBANG help This simple GPIO bitbanging SPI master uses the arch-neutral GPIO @@ -179,16 +217,15 @@ config SPI_GPIO config SPI_IMX tristate "Freescale i.MX SPI controllers" - depends on ARCH_MXC + depends on ARCH_MXC || COMPILE_TEST select SPI_BITBANG - default m if IMX_HAVE_PLATFORM_SPI_IMX help This enables using the Freescale i.MX SPI controllers in master mode. config SPI_LM70_LLP tristate "Parallel port adapter for LM70 eval board (DEVELOPMENT)" - depends on PARPORT && EXPERIMENTAL + depends on PARPORT select SPI_BITBANG help This driver supports the NS LM70 LLP Evaluation Board, @@ -204,7 +241,7 @@ config SPI_MPC52xx config SPI_MPC52xx_PSC tristate "Freescale MPC52xx PSC SPI controller" - depends on PPC_MPC52xx && EXPERIMENTAL + depends on PPC_MPC52xx help This enables using the Freescale MPC52xx Programmable Serial Controller in master SPI mode. @@ -218,16 +255,32 @@ config SPI_MPC512x_PSC config SPI_FSL_LIB tristate + depends on OF + +config SPI_FSL_CPM + tristate depends on FSL_SOC config SPI_FSL_SPI - bool "Freescale SPI controller" - depends on FSL_SOC + bool "Freescale SPI controller and Aeroflex Gaisler GRLIB SPI controller" + depends on OF select SPI_FSL_LIB + select SPI_FSL_CPM if FSL_SOC help This enables using the Freescale SPI controllers in master mode. MPC83xx platform uses the controller in cpu mode or CPM/QE mode. MPC8569 uses the controller in QE mode, MPC8610 in cpu mode. + This also enables using the Aeroflex Gaisler GRLIB SPI controller in + master mode. + +config SPI_FSL_DSPI + tristate "Freescale DSPI controller" + select SPI_BITBANG + select REGMAP_MMIO + depends on SOC_VF610 || COMPILE_TEST + help + This enables support for the Freescale DSPI controller in master + mode. VF610 platform uses the controller. config SPI_FSL_ESPI bool "Freescale eSPI controller" @@ -240,14 +293,14 @@ config SPI_FSL_ESPI config SPI_OC_TINY tristate "OpenCores tiny SPI" - depends on GENERIC_GPIO + depends on GPIOLIB select SPI_BITBANG help This is the driver for OpenCores tiny SPI master controller. config SPI_OCTEON tristate "Cavium OCTEON SPI controller" - depends on CPU_CAVIUM_OCTEON + depends on CAVIUM_OCTEON_SOC help SPI host driver for the hardware found on some Cavium OCTEON SOCs. @@ -261,20 +314,29 @@ config SPI_OMAP_UWIRE config SPI_OMAP24XX tristate "McSPI driver for OMAP" - depends on ARCH_OMAP2PLUS + depends on ARM || ARM64 || AVR32 || HEXAGON || MIPS || SUPERH + depends on ARCH_OMAP2PLUS || COMPILE_TEST help SPI master controller for OMAP24XX and later Multichannel SPI (McSPI) modules. +config SPI_TI_QSPI + tristate "DRA7xxx QSPI controller support" + depends on ARCH_OMAP2PLUS || COMPILE_TEST + help + QSPI master controller for DRA7xxx used for flash devices. + This device supports single, dual and quad read support, while + it only supports single write mode. + config SPI_OMAP_100K tristate "OMAP SPI 100K" - depends on ARCH_OMAP850 || ARCH_OMAP730 + depends on ARCH_OMAP850 || ARCH_OMAP730 || COMPILE_TEST help OMAP SPI 100K master controller for omap7xx boards. config SPI_ORION - tristate "Orion SPI master (EXPERIMENTAL)" - depends on PLAT_ORION && EXPERIMENTAL + tristate "Orion SPI master" + depends on PLAT_ORION || COMPILE_TEST help This enables using the SPI master controller on the Orion chips. @@ -297,9 +359,20 @@ config SPI_PPC4xx help This selects a driver for the PPC4xx SPI Controller. +config SPI_PXA2XX_PXADMA + bool "PXA2xx SSP legacy PXA DMA API support" + depends on SPI_PXA2XX && ARCH_PXA + help + Enable PXA private legacy DMA API support. Note that this is + deprecated in favor of generic DMA engine API. + +config SPI_PXA2XX_DMA + def_bool y + depends on SPI_PXA2XX && !SPI_PXA2XX_PXADMA + config SPI_PXA2XX tristate "PXA2xx SSP SPI master" - depends on (ARCH_PXA || (X86_32 && PCI)) && EXPERIMENTAL + depends on (ARCH_PXA || PCI || ACPI) select PXA_SSP if ARCH_PXA help This enables using a PXA2xx or Sodaville SSP port as a SPI master @@ -307,17 +380,30 @@ config SPI_PXA2XX additional documentation can be found a Documentation/spi/pxa2xx. config SPI_PXA2XX_PCI - def_bool SPI_PXA2XX && X86_32 && PCI + def_tristate SPI_PXA2XX && PCI config SPI_RSPI - tristate "Renesas RSPI controller" - depends on SUPERH + tristate "Renesas RSPI/QSPI controller" + depends on (SUPERH && SH_DMAE_BASE) || ARCH_SHMOBILE + help + SPI driver for Renesas RSPI and QSPI blocks. + +config SPI_QUP + tristate "Qualcomm SPI controller with QUP interface" + depends on ARCH_QCOM || (ARM && COMPILE_TEST) help - SPI driver for Renesas RSPI blocks. + Qualcomm Universal Peripheral (QUP) core is an AHB slave that + provides a common data path (an output FIFO and an input FIFO) + for serial peripheral interface (SPI) mini-core. SPI in master + mode supports up to 50MHz, up to four chip selects, programmable + data path from 4 bits to 32 bits and numerous protocol variants. + + This driver can also be built as a module. If so, the module + will be called spi_qup. config SPI_S3C24XX tristate "Samsung S3C24XX series SPI" - depends on ARCH_S3C24XX && EXPERIMENTAL + depends on ARCH_S3C24XX select SPI_BITBANG help SPI driver for Samsung S3C24XX series ARM SoCs @@ -335,8 +421,8 @@ config SPI_S3C24XX_FIQ config SPI_S3C64XX tristate "Samsung S3C64XX series type SPI" - depends on (ARCH_S3C24XX || ARCH_S3C64XX || ARCH_S5P64X0 || ARCH_EXYNOS) - select S3C64XX_DMA if ARCH_S3C64XX + depends on PLAT_SAMSUNG + select S3C64XX_PL080 if ARCH_S3C64XX help SPI driver for Samsung S3C64XX and newer SoCs. @@ -348,14 +434,14 @@ config SPI_SC18IS602 config SPI_SH_MSIOF tristate "SuperH MSIOF SPI controller" - depends on (SUPERH || ARCH_SHMOBILE) && HAVE_CLK - select SPI_BITBANG + depends on HAVE_CLK + depends on SUPERH || ARCH_SHMOBILE || COMPILE_TEST help SPI driver for SuperH and SH Mobile MSIOF blocks. config SPI_SH tristate "SuperH SPI controller" - depends on SUPERH + depends on SUPERH || COMPILE_TEST help SPI driver for SuperH SPI blocks. @@ -368,17 +454,30 @@ config SPI_SH_SCI config SPI_SH_HSPI tristate "SuperH HSPI controller" - depends on ARCH_SHMOBILE + depends on ARCH_SHMOBILE || COMPILE_TEST help SPI driver for SuperH HSPI blocks. config SPI_SIRF tristate "CSR SiRFprimaII SPI controller" - depends on ARCH_PRIMA2 + depends on SIRF_DMA select SPI_BITBANG help SPI driver for CSR SiRFprimaII SoCs +config SPI_SUN4I + tristate "Allwinner A10 SoCs SPI controller" + depends on ARCH_SUNXI || COMPILE_TEST + help + SPI driver for Allwinner sun4i, sun5i and sun7i SoCs + +config SPI_SUN6I + tristate "Allwinner A31 SPI controller" + depends on ARCH_SUNXI || COMPILE_TEST + depends on RESET_CONTROLLER + help + This enables using the SPI controller on the Allwinner A31 SoCs. + config SPI_MXS tristate "Freescale MXS SPI controller" depends on ARCH_MXS @@ -386,9 +485,19 @@ config SPI_MXS help SPI driver for Freescale MXS devices. +config SPI_TEGRA114 + tristate "NVIDIA Tegra114 SPI Controller" + depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST + depends on RESET_CONTROLLER + help + SPI driver for NVIDIA Tegra114 SPI Controller interface. This controller + is different than the older SoCs SPI controller and also register interface + get changed with this controller. + config SPI_TEGRA20_SFLASH tristate "Nvidia Tegra20 Serial flash Controller" - depends on ARCH_TEGRA + depends on ARCH_TEGRA || COMPILE_TEST + depends on RESET_CONTROLLER help SPI driver for Nvidia Tegra20 Serial flash Controller interface. The main usecase of this controller is to use spi flash as boot @@ -396,20 +505,14 @@ config SPI_TEGRA20_SFLASH config SPI_TEGRA20_SLINK tristate "Nvidia Tegra20/Tegra30 SLINK Controller" - depends on ARCH_TEGRA && TEGRA20_APB_DMA + depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST + depends on RESET_CONTROLLER help SPI driver for Nvidia Tegra20/Tegra30 SLINK Controller interface. -config SPI_TI_SSP - tristate "TI Sequencer Serial Port - SPI Support" - depends on MFD_TI_SSP - help - This selects an SPI master implementation using a TI sequencer - serial port. - config SPI_TOPCLIFF_PCH tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) SPI" - depends on PCI + depends on PCI && (X86_32 || COMPILE_TEST) help SPI driver for the Topcliff PCH (Platform Controller Hub) SPI bus used in some x86 embedded processors. @@ -419,7 +522,7 @@ config SPI_TOPCLIFF_PCH config SPI_TXX9 tristate "Toshiba TXx9 SPI controller" - depends on GENERIC_GPIO && CPU_TX49XX + depends on GPIOLIB && (CPU_TX49XX || COMPILE_TEST) help SPI driver for Toshiba TXx9 MIPS SoCs @@ -432,7 +535,7 @@ config SPI_XCOMM config SPI_XILINX tristate "Xilinx SPI controller common module" - depends on HAS_IOMEM && EXPERIMENTAL + depends on HAS_IOMEM select SPI_BITBANG help This exposes the SPI controller IP from the Xilinx EDK. @@ -442,9 +545,22 @@ config SPI_XILINX Or for the DS570, see "XPS Serial Peripheral Interface (SPI) (v2.00b)" +config SPI_XTENSA_XTFPGA + tristate "Xtensa SPI controller for xtfpga" + depends on (XTENSA && XTENSA_PLATFORM_XTFPGA) || COMPILE_TEST + select SPI_BITBANG + help + SPI driver for xtfpga SPI master controller. + + This simple SPI master controller is built into xtfpga bitstreams + and is used to control daughterboard audio codec. It always transfers + 16 bit words in SPI mode 0, automatically asserting CS on transfer + start and deasserting on end. + + config SPI_NUC900 tristate "Nuvoton NUC900 series SPI" - depends on ARCH_W90X900 && EXPERIMENTAL + depends on ARCH_W90X900 select SPI_BITBANG help SPI driver for Nuvoton NUC900 series ARM SoCs @@ -468,7 +584,7 @@ config SPI_DW_MID_DMA config SPI_DW_MMIO tristate "Memory-mapped io interface driver for DW SPI core" - depends on SPI_DESIGNWARE && HAVE_CLK + depends on SPI_DESIGNWARE # # There are lots of SPI device types, with sensors and memory @@ -478,7 +594,6 @@ comment "SPI Protocol Masters" config SPI_SPIDEV tristate "User mode SPI device driver support" - depends on EXPERIMENTAL help This supports user mode SPI protocol drivers. |