diff options
Diffstat (limited to 'drivers/serial')
| -rw-r--r-- | drivers/serial/Kconfig | 54 | ||||
| -rw-r--r-- | drivers/serial/Makefile | 4 | ||||
| -rw-r--r-- | drivers/serial/s3c2400.c | 106 | ||||
| -rw-r--r-- | drivers/serial/s3c2410.c | 1860 | ||||
| -rw-r--r-- | drivers/serial/s3c2412.c | 151 | ||||
| -rw-r--r-- | drivers/serial/s3c2440.c | 181 | ||||
| -rw-r--r-- | drivers/serial/samsung.c | 1317 | ||||
| -rw-r--r-- | drivers/serial/samsung.h | 102 |
8 files changed, 1923 insertions, 1852 deletions
diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig index 0843c540068..18ca9075e13 100644 --- a/drivers/serial/Kconfig +++ b/drivers/serial/Kconfig @@ -448,22 +448,27 @@ config SERIAL_CLPS711X_CONSOLE your boot loader (lilo or loadlin) about how to pass options to the kernel at boot time.) -config SERIAL_S3C2410 - tristate "Samsung S3C2410/S3C2440/S3C2442/S3C2412 Serial port support" - depends on ARM && ARCH_S3C2410 - select SERIAL_CORE +config SERIAL_SAMSUNG + tristate "Samsung SoC serial support" + depends on ARM && PLAT_S3C24XX help Support for the on-chip UARTs on the Samsung S3C24XX series CPUs, providing /dev/ttySAC0, 1 and 2 (note, some machines may not provide all of these ports, depending on how the serial port pins are configured. - Currently this driver supports the UARTS on the S3C2410, S3C2440, - S3C2442, S3C2412 and S3C2413 CPUs. +config SERIAL_SAMSUNG_DEBUG + bool "Samsung SoC serial debug" + depends on SERIAL_SAMSUNG + help + Add support for debugging the serial driver. Since this is + generally being used as a console, we use our own output + routines that go via the low-level debug printascii() + function. -config SERIAL_S3C2410_CONSOLE - bool "Support for console on S3C2410 serial port" - depends on SERIAL_S3C2410=y +config SERIAL_SAMSUNG_CONSOLE + bool "Support for console on Samsung SoC serial port" + depends on SERIAL_SAMSUNG=y select SERIAL_CORE_CONSOLE help Allow selection of the S3C24XX on-board serial ports for use as @@ -476,6 +481,37 @@ config SERIAL_S3C2410_CONSOLE your boot loader about how to pass options to the kernel at boot time.) +config SERIAL_S3C2400 + tristate "Samsung S3C2410 Serial port support" + depends on ARM && SERIAL_SAMSUNG && CPU_S3C2400 + default y if CPU_S3C2400 + help + Serial port support for the Samsung S3C2400 SoC + +config SERIAL_S3C2410 + tristate "Samsung S3C2410 Serial port support" + depends on SERIAL_SAMSUNG && CPU_S3C2410 + default y if CPU_S3C2410 + help + Serial port support for the Samsung S3C2410 SoC + +config SERIAL_S3C2412 + tristate "Samsung S3C2412/S3C2413 Serial port support" + depends on SERIAL_SAMSUNG && CPU_S3C2412 + default y if CPU_S3C2412 + help + Serial port support for the Samsung S3C2412 and S3C2413 SoC + +config SERIAL_S3C2440 + tristate "Samsung S3C2440/S3C2442 Serial port support" + depends on SERIAL_SAMSUNG && (CPU_S3C2440 || CPU_S3C2442) + default y if CPU_S3C2440 + default y if CPU_S3C2442 + help + Serial port support for the Samsung S3C2440 and S3C2442 SoC + + + config SERIAL_DZ bool "DECstation DZ serial driver" depends on MACH_DECSTATION && 32BIT diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile index 0d9c09b1e83..7d85c1fbe7e 100644 --- a/drivers/serial/Makefile +++ b/drivers/serial/Makefile @@ -28,7 +28,11 @@ obj-$(CONFIG_SERIAL_PNX8XXX) += pnx8xxx_uart.o obj-$(CONFIG_SERIAL_SA1100) += sa1100.o obj-$(CONFIG_SERIAL_BFIN) += bfin_5xx.o obj-$(CONFIG_SERIAL_BFIN_SPORT) += bfin_sport_uart.o +obj-$(CONFIG_SERIAL_SAMSUNG) += samsung.o +obj-$(CONFIG_SERIAL_S3C2400) += s3c2400.o obj-$(CONFIG_SERIAL_S3C2410) += s3c2410.o +obj-$(CONFIG_SERIAL_S3C2412) += s3c2412.o +obj-$(CONFIG_SERIAL_S3C2440) += s3c2440.o obj-$(CONFIG_SERIAL_SUNCORE) += suncore.o obj-$(CONFIG_SERIAL_SUNHV) += sunhv.o obj-$(CONFIG_SERIAL_SUNZILOG) += sunzilog.o diff --git a/drivers/serial/s3c2400.c b/drivers/serial/s3c2400.c new file mode 100644 index 00000000000..a1102053e55 --- /dev/null +++ b/drivers/serial/s3c2400.c @@ -0,0 +1,106 @@ +/* linux/drivers/serial/s3c240.c + * + * Driver for Samsung SoC onboard UARTs. + * + * Ben Dooks, Copyright (c) 2003-2005 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <linux/module.h> +#include <linux/ioport.h> +#include <linux/io.h> +#include <linux/platform_device.h> + +#include <asm/irq.h> + +#include <asm/hardware.h> + +#include <asm/plat-s3c/regs-serial.h> +#include <asm/arch/regs-gpio.h> + +#include "samsung.h" + +static int s3c2400_serial_getsource(struct uart_port *port, + struct s3c24xx_uart_clksrc *clk) +{ + clk->divisor = 1; + clk->name = "pclk"; + + return 0; +} + +static int s3c2400_serial_setsource(struct uart_port *port, + struct s3c24xx_uart_clksrc *clk) +{ + return 0; +} + +static int s3c2400_serial_resetport(struct uart_port *port, + struct s3c2410_uartcfg *cfg) +{ + dbg("s3c2400_serial_resetport: port=%p (%08lx), cfg=%p\n", + port, port->mapbase, cfg); + + wr_regl(port, S3C2410_UCON, cfg->ucon); + wr_regl(port, S3C2410_ULCON, cfg->ulcon); + + /* reset both fifos */ + + wr_regl(port, S3C2410_UFCON, cfg->ufcon | S3C2410_UFCON_RESETBOTH); + wr_regl(port, S3C2410_UFCON, cfg->ufcon); + + return 0; +} + +static struct s3c24xx_uart_info s3c2400_uart_inf = { + .name = "Samsung S3C2400 UART", + .type = PORT_S3C2400, + .fifosize = 16, + .rx_fifomask = S3C2410_UFSTAT_RXMASK, + .rx_fifoshift = S3C2410_UFSTAT_RXSHIFT, + .rx_fifofull = S3C2410_UFSTAT_RXFULL, + .tx_fifofull = S3C2410_UFSTAT_TXFULL, + .tx_fifomask = S3C2410_UFSTAT_TXMASK, + .tx_fifoshift = S3C2410_UFSTAT_TXSHIFT, + .get_clksrc = s3c2400_serial_getsource, + .set_clksrc = s3c2400_serial_setsource, + .reset_port = s3c2400_serial_resetport, +}; + +static int s3c2400_serial_probe(struct platform_device *dev) +{ + return s3c24xx_serial_probe(dev, &s3c2400_uart_inf); +} + +static struct platform_driver s3c2400_serial_drv = { + .probe = s3c2400_serial_probe, + .remove = s3c24xx_serial_remove, + .driver = { + .name = "s3c2400-uart", + .owner = THIS_MODULE, + }, +}; + +s3c24xx_console_init(&s3c2400_serial_drv, &s3c2400_uart_inf); + +static inline int s3c2400_serial_init(void) +{ + return s3c24xx_serial_init(&s3c2400_serial_drv, &s3c2400_uart_inf); +} + +static inline void s3c2400_serial_exit(void) +{ + platform_driver_unregister(&s3c2400_serial_drv); +} + +module_init(s3c2400_serial_init); +module_exit(s3c2400_serial_exit); + +MODULE_LICENSE("GPL v2"); +MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>"); +MODULE_DESCRIPTION("Samsung S3C2400 SoC Serial port driver"); +MODULE_ALIAS("platform:s3c2400-uart"); diff --git a/drivers/serial/s3c2410.c b/drivers/serial/s3c2410.c index 2b6a013639e..c5f03f41686 100644 --- a/drivers/serial/s3c2410.c +++ b/drivers/serial/s3c2410.c @@ -1,1270 +1,30 @@ -/* - * linux/drivers/serial/s3c2410.c +/* linux/drivers/serial/s3c2410.c * - * Driver for onboard UARTs on the Samsung S3C24XX + * Driver for Samsung S3C2410 SoC onboard UARTs. * - * Based on drivers/char/serial.c and drivers/char/21285.c + * Ben Dooks, Copyright (c) 2003-2005,2008 Simtec Electronics + * http://armlinux.simtec.co.uk/ * - * Ben Dooks, (c) 2003-2005 Simtec Electronics - * http://www.simtec.co.uk/products/SWLINUX/ - * - * Changelog: - * - * 22-Jul-2004 BJD Finished off device rewrite - * - * 21-Jul-2004 BJD Thanks to <herbet@13thfloor.at> for pointing out - * problems with baud rate and loss of IR settings. Update - * to add configuration via platform_device structure - * - * 28-Sep-2004 BJD Re-write for the following items - * - S3C2410 and S3C2440 serial support - * - Power Management support - * - Fix console via IrDA devices - * - SysReq (Herbert Pötzl) - * - Break character handling (Herbert Pötzl) - * - spin-lock initialisation (Dimitry Andric) - * - added clock control - * - updated init code to use platform_device info - * - * 06-Mar-2005 BJD Add s3c2440 fclk clock source - * - * 09-Mar-2005 BJD Add s3c2400 support - * - * 10-Mar-2005 LCVR Changed S3C2410_VA_UART to S3C24XX_VA_UART -*/ - -/* Note on 2440 fclk clock source handling - * - * Whilst it is possible to use the fclk as clock source, the method - * of properly switching too/from this is currently un-implemented, so - * whichever way is configured at startup is the one that will be used. -*/ - -/* Hote on 2410 error handling - * - * The s3c2410 manual has a love/hate affair with the contents of the - * UERSTAT register in the UART blocks, and keeps marking some of the - * error bits as reserved. Having checked with the s3c2410x01, - * it copes with BREAKs properly, so I am happy to ignore the RESERVED - * feature from the latter versions of the manual. - * - * If it becomes aparrent that latter versions of the 2410 remove these - * bits, then action will have to be taken to differentiate the versions - * and change the policy on BREAK - * - * BJD, 04-Nov-2004 + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. */ - -#if defined(CONFIG_SERIAL_S3C2410_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) -#define SUPPORT_SYSRQ -#endif - #include <linux/module.h> #include <linux/ioport.h> +#include <linux/io.h> #include <linux/platform_device.h> #include <linux/init.h> -#include <linux/sysrq.h> -#include <linux/console.h> -#include <linux/tty.h> -#include <linux/tty_flip.h> #include <linux/serial_core.h> #include <linux/serial.h> -#include <linux/delay.h> -#include <linux/clk.h> -#include <asm/io.h> #include <asm/irq.h> - #include <asm/hardware.h> #include <asm/plat-s3c/regs-serial.h> #include <asm/arch/regs-gpio.h> -/* structures */ - -struct s3c24xx_uart_info { - char *name; - unsigned int type; - unsigned int fifosize; - unsigned long rx_fifomask; - unsigned long rx_fifoshift; - unsigned long rx_fifofull; - unsigned long tx_fifomask; - unsigned long tx_fifoshift; - unsigned long tx_fifofull; - - /* clock source control */ - - int (*get_clksrc)(struct uart_port *, struct s3c24xx_uart_clksrc *clk); - int (*set_clksrc)(struct uart_port *, struct s3c24xx_uart_clksrc *clk); - - /* uart controls */ - int (*reset_port)(struct uart_port *, struct s3c2410_uartcfg *); -}; - -struct s3c24xx_uart_port { - unsigned char rx_claimed; - unsigned char tx_claimed; - - struct s3c24xx_uart_info *info; - struct s3c24xx_uart_clksrc *clksrc; - struct clk *clk; - struct clk *baudclk; - struct uart_port port; -}; - - -/* configuration defines */ - -#if 0 -#if 1 -/* send debug to the low-level output routines */ - -extern void printascii(const char *); - -static void -s3c24xx_serial_dbg(const char *fmt, ...) -{ - va_list va; - char buff[256]; - - va_start(va, fmt); - vsprintf(buff, fmt, va); - va_end(va); - - printascii(buff); -} - -#define dbg(x...) s3c24xx_serial_dbg(x) - -#else -#define dbg(x...) printk(KERN_DEBUG "s3c24xx: "); -#endif -#else /* no debug */ -#define dbg(x...) do {} while(0) -#endif - -/* UART name and device definitions */ - -#define S3C24XX_SERIAL_NAME "ttySAC" -#define S3C24XX_SERIAL_MAJOR 204 -#define S3C24XX_SERIAL_MINOR 64 - - -/* conversion functions */ - -#define s3c24xx_dev_to_port(__dev) (struct uart_port *)dev_get_drvdata(__dev) -#define s3c24xx_dev_to_cfg(__dev) (struct s3c2410_uartcfg *)((__dev)->platform_data) - -/* we can support 3 uarts, but not always use them */ - -#ifdef CONFIG_CPU_S3C2400 -#define NR_PORTS (2) -#else -#define NR_PORTS (3) -#endif - -/* port irq numbers */ - -#define TX_IRQ(port) ((port)->irq + 1) -#define RX_IRQ(port) ((port)->irq) - -/* register access controls */ - -#define portaddr(port, reg) ((port)->membase + (reg)) - -#define rd_regb(port, reg) (__raw_readb(portaddr(port, reg))) -#define rd_regl(port, reg) (__raw_readl(portaddr(port, reg))) - -#define wr_regb(port, reg, val) \ - do { __raw_writeb(val, portaddr(port, reg)); } while(0) - -#define wr_regl(port, reg, val) \ - do { __raw_writel(val, portaddr(port, reg)); } while(0) - -/* macros to change one thing to another */ - -#define tx_enabled(port) ((port)->unused[0]) -#define rx_enabled(port) ((port)->unused[1]) - -/* flag to ignore all characters comming in */ -#define RXSTAT_DUMMY_READ (0x10000000) - -static inline struct s3c24xx_uart_port *to_ourport(struct uart_port *port) -{ - return container_of(port, struct s3c24xx_uart_port, port); -} - -/* translate a port to the device name */ - -static inline const char *s3c24xx_serial_portname(struct uart_port *port) -{ - return to_platform_device(port->dev)->name; -} - -static int s3c24xx_serial_txempty_nofifo(struct uart_port *port) -{ - return (rd_regl(port, S3C2410_UTRSTAT) & S3C2410_UTRSTAT_TXE); -} - -static void s3c24xx_serial_rx_enable(struct uart_port *port) -{ - unsigned long flags; - unsigned int ucon, ufcon; - int count = 10000; - - spin_lock_irqsave(&port->lock, flags); - - while (--count && !s3c24xx_serial_txempty_nofifo(port)) - udelay(100); - - ufcon = rd_regl(port, S3C2410_UFCON); - ufcon |= S3C2410_UFCON_RESETRX; - wr_regl(port, S3C2410_UFCON, ufcon); - - ucon = rd_regl(port, S3C2410_UCON); - ucon |= S3C2410_UCON_RXIRQMODE; - wr_regl(port, S3C2410_UCON, ucon); - - rx_enabled(port) = 1; - spin_unlock_irqrestore(&port->lock, flags); -} - -static void s3c24xx_serial_rx_disable(struct uart_port *port) -{ - unsigned long flags; - unsigned int ucon; - - spin_lock_irqsave(&port->lock, flags); - - ucon = rd_regl(port, S3C2410_UCON); - ucon &= ~S3C2410_UCON_RXIRQMODE; - wr_regl(port, S3C2410_UCON, ucon); - - rx_enabled(port) = 0; - spin_unlock_irqrestore(&port->lock, flags); -} - -static void s3c24xx_serial_stop_tx(struct uart_port *port) -{ - if (tx_enabled(port)) { - disable_irq(TX_IRQ(port)); - tx_enabled(port) = 0; - if (port->flags & UPF_CONS_FLOW) - s3c24xx_serial_rx_enable(port); - } -} - -static void s3c24xx_serial_start_tx(struct uart_port *port) -{ - if (!tx_enabled(port)) { - if (port->flags & UPF_CONS_FLOW) - s3c24xx_serial_rx_disable(port); - - enable_irq(TX_IRQ(port)); - tx_enabled(port) = 1; - } -} - - -static void s3c24xx_serial_stop_rx(struct uart_port *port) -{ - if (rx_enabled(port)) { - dbg("s3c24xx_serial_stop_rx: port=%p\n", port); - disable_irq(RX_IRQ(port)); - rx_enabled(port) = 0; - } -} - -static void s3c24xx_serial_enable_ms(struct uart_port *port) -{ -} - -static inline struct s3c24xx_uart_info *s3c24xx_port_to_info(struct uart_port *port) -{ - return to_ourport(port)->info; -} - -static inline struct s3c2410_uartcfg *s3c24xx_port_to_cfg(struct uart_port *port) -{ - if (port->dev == NULL) - return NULL; - - return (struct s3c2410_uartcfg *)port->dev->platform_data; -} - -static int s3c24xx_serial_rx_fifocnt(struct s3c24xx_uart_port *ourport, - unsigned long ufstat) -{ - struct s3c24xx_uart_info *info = ourport->info; - - if (ufstat & info->rx_fifofull) - return info->fifosize; - - return (ufstat & info->rx_fifomask) >> info->rx_fifoshift; -} - - -/* ? - where has parity gone?? */ -#define S3C2410_UERSTAT_PARITY (0x1000) - -static irqreturn_t -s3c24xx_serial_rx_chars(int irq, void *dev_id) -{ - struct s3c24xx_uart_port *ourport = dev_id; - struct uart_port *port = &ourport->port; - struct tty_struct *tty = port->info->tty; - unsigned int ufcon, ch, flag, ufstat, uerstat; - int max_count = 64; - - while (max_count-- > 0) { - ufcon = rd_regl(port, S3C2410_UFCON); - ufstat = rd_regl(port, S3C2410_UFSTAT); - - if (s3c24xx_serial_rx_fifocnt(ourport, ufstat) == 0) - break; - - uerstat = rd_regl(port, S3C2410_UERSTAT); - ch = rd_regb(port, S3C2410_URXH); - - if (port->flags & UPF_CONS_FLOW) { - int txe = s3c24xx_serial_txempty_nofifo(port); - - if (rx_enabled(port)) { - if (!txe) { - rx_enabled(port) = 0; - continue; - } - } else { - if (txe) { - ufcon |= S3C2410_UFCON_RESETRX; - wr_regl(port, S3C2410_UFCON, ufcon); - rx_enabled(port) = 1; - goto out; - } - continue; - } - } - - /* insert the character into the buffer */ - - flag = TTY_NORMAL; - port->icount.rx++; - - if (unlikely(uerstat & S3C2410_UERSTAT_ANY)) { - dbg("rxerr: port ch=0x%02x, rxs=0x%08x\n", - ch, uerstat); - - /* check for break */ - if (uerstat & S3C2410_UERSTAT_BREAK) { - dbg("break!\n"); - port->icount.brk++; - if (uart_handle_break(port)) - goto ignore_char; - } - - if (uerstat & S3C2410_UERSTAT_FRAME) - port->icount.frame++; - if (uerstat & S3C2410_UERSTAT_OVERRUN) - port->icount.overrun++; - - uerstat &= port->read_status_mask; - - if (uerstat & S3C2410_UERSTAT_BREAK) - flag = TTY_BREAK; - else if (uerstat & S3C2410_UERSTAT_PARITY) - flag = TTY_PARITY; - else if (uerstat & ( S3C2410_UERSTAT_FRAME | S3C2410_UERSTAT_OVERRUN)) - flag = TTY_FRAME; - } - - if (uart_handle_sysrq_char(port, ch)) - goto ignore_char; - - uart_insert_char(port, uerstat, S3C2410_UERSTAT_OVERRUN, ch, flag); - - ignore_char: - continue; - } - tty_flip_buffer_push(tty); - - out: - return IRQ_HANDLED; -} - -static irqreturn_t s3c24xx_serial_tx_chars(int irq, void *id) -{ - struct s3c24xx_uart_port *ourport = id; - struct uart_port *port = &ourport->port; - struct circ_buf *xmit = &port->info->xmit; - int count = 256; - - if (port->x_char) { - wr_regb(port, S3C2410_UTXH, port->x_char); - port->icount.tx++; - port->x_char = 0; - goto out; - } - - /* if there isnt anything more to transmit, or the uart is now - * stopped, disable the uart and exit - */ - - if (uart_circ_empty(xmit) || uart_tx_stopped(port)) { - s3c24xx_serial_stop_tx(port); - goto out; - } - - /* try and drain the buffer... */ - - while (!uart_circ_empty(xmit) && count-- > 0) { - if (rd_regl(port, S3C2410_UFSTAT) & ourport->info->tx_fifofull) - break; - - wr_regb(port, S3C2410_UTXH, xmit->buf[xmit->tail]); - xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); - port->icount.tx++; - } - - if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) - uart_write_wakeup(port); - - if (uart_circ_empty(xmit)) - s3c24xx_serial_stop_tx(port); - - out: - return IRQ_HANDLED; -} - -static unsigned int s3c24xx_serial_tx_empty(struct uart_port *port) -{ - struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port); - unsigned long ufstat = rd_regl(port, S3C2410_UFSTAT); - unsigned long ufcon = rd_regl(port, S3C2410_UFCON); - - if (ufcon & S3C2410_UFCON_FIFOMODE) { - if ((ufstat & info->tx_fifomask) != 0 || - (ufstat & info->tx_fifofull)) - return 0; - - return 1; - } - - return s3c24xx_serial_txempty_nofifo(port); -} - -/* no modem control lines */ -static unsigned int s3c24xx_serial_get_mctrl(struct uart_port *port) -{ - unsigned int umstat = rd_regb(port,S3C2410_UMSTAT); - - if (umstat & S3C2410_UMSTAT_CTS) - return TIOCM_CAR | TIOCM_DSR | TIOCM_CTS; - else - return TIOCM_CAR | TIOCM_DSR; -} - -static void s3c24xx_serial_set_mctrl(struct uart_port *port, unsigned int mctrl) -{ - /* todo - possibly remove AFC and do manual CTS */ -} - -static void s3c24xx_serial_break_ctl(struct uart_port *port, int break_state) -{ - unsigned long flags; - unsigned int ucon; - - spin_lock_irqsave(&port->lock, flags); - - ucon = rd_regl(port, S3C2410_UCON); - - if (break_state) - ucon |= S3C2410_UCON_SBREAK; - else - ucon &= ~S3C2410_UCON_SBREAK; - - wr_regl(port, S3C2410_UCON, ucon); - - spin_unlock_irqrestore(&port->lock, flags); -} - -static void s3c24xx_serial_shutdown(struct uart_port *port) -{ - struct s3c24xx_uart_port *ourport = to_ourport(port); - - if (ourport->tx_claimed) { - free_irq(TX_IRQ(port), ourport); - tx_enabled(port) = 0; - ourport->tx_claimed = 0; - } - - if (ourport->rx_claimed) { - free_irq(RX_IRQ(port), ourport); - ourport->rx_claimed = 0; - rx_enabled(port) = 0; - } -} - - -static int s3c24xx_serial_startup(struct uart_port *port) -{ - struct s3c24xx_uart_port *ourport = to_ourport(port); - int ret; - - dbg("s3c24xx_serial_startup: port=%p (%08lx,%p)\n", - port->mapbase, port->membase); - - rx_enabled(port) = 1; - - ret = request_irq(RX_IRQ(port), - s3c24xx_serial_rx_chars, 0, - s3c24xx_serial_portname(port), ourport); - - if (ret != 0) { - printk(KERN_ERR "cannot get irq %d\n", RX_IRQ(port)); - return ret; - } - - ourport->rx_claimed = 1; - - dbg("requesting tx irq...\n"); - - tx_enabled(port) = 1; - - ret = request_irq(TX_IRQ(port), - s3c24xx_serial_tx_chars, 0, - s3c24xx_serial_portname(port), ourport); - - if (ret) { - printk(KERN_ERR "cannot get irq %d\n", TX_IRQ(port)); - goto err; - } - - ourport->tx_claimed = 1; - - dbg("s3c24xx_serial_startup ok\n"); - - /* the port reset code should have done the correct - * register setup for the port controls */ - - return ret; - - err: - s3c24xx_serial_shutdown(port); - return ret; -} - -/* power power management control */ - -static void s3c24xx_serial_pm(struct uart_port *port, unsigned int level, - unsigned int old) -{ - struct s3c24xx_uart_port *ourport = to_ourport(port); - - switch (level) { - case 3: - if (!IS_ERR(ourport->baudclk) && ourport->baudclk != NULL) - clk_disable(ourport->baudclk); - - clk_disable(ourport->clk); - break; - - case 0: - clk_enable(ourport->clk); - - if (!IS_ERR(ourport->baudclk) && ourport->baudclk != NULL) - clk_enable(ourport->baudclk); - - break; - default: - printk(KERN_ERR "s3c24xx_serial: unknown pm %d\n", level); - } -} - -/* baud rate calculation - * - * The UARTs on the S3C2410/S3C2440 can take their clocks from a number - * of different sources, including the peripheral clock ("pclk") and an - * external clock ("uclk"). The S3C2440 also adds the core clock ("fclk") - * with a programmable extra divisor. - * - * The following code goes through the clock sources, and calculates the - * baud clocks (and the resultant actual baud rates) and then tries to - * pick the closest one and select that. - * -*/ - - -#define MAX_CLKS (8) - -static struct s3c24xx_uart_clksrc tmp_clksrc = { - .name = "pclk", - .min_baud = 0, - .max_baud = 0, - .divisor = 1, -}; - -static inline int -s3c24xx_serial_getsource(struct uart_port *port, struct s3c24xx_uart_clksrc *c) -{ - struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port); - - return (info->get_clksrc)(port, c); -} - -static inline int -s3c24xx_serial_setsource(struct uart_port *port, struct s3c24xx_uart_clksrc *c) -{ - struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port); - - return (info->set_clksrc)(port, c); -} - -struct baud_calc { - struct s3c24xx_uart_clksrc *clksrc; - unsigned int calc; - unsigned int quot; - struct clk *src; -}; - -static int s3c24xx_serial_calcbaud(struct baud_calc *calc, - struct uart_port *port, - struct s3c24xx_uart_clksrc *clksrc, - unsigned int baud) -{ - unsigned long rate; - - calc->src = clk_get(port->dev, clksrc->name); - if (calc->src == NULL || IS_ERR(calc->src)) - return 0; - - rate = clk_get_rate(calc->src); - rate /= clksrc->divisor; - - calc->clksrc = clksrc; - calc->quot = (rate + (8 * baud)) / (16 * baud); - calc->calc = (rate / (calc->quot * 16)); - - calc->quot--; - return 1; -} - -static unsigned int s3c24xx_serial_getclk(struct uart_port *port, - struct s3c24xx_uart_clksrc **clksrc, - struct clk **clk, - unsigned int baud) -{ - struct s3c2410_uartcfg *cfg = s3c24xx_port_to_cfg(port); - struct s3c24xx_uart_clksrc *clkp; - struct baud_calc res[MAX_CLKS]; - struct baud_calc *resptr, *best, *sptr; - int i; - - clkp = cfg->clocks; - best = NULL; - - if (cfg->clocks_size < 2) { - if (cfg->clocks_size == 0) - clkp = &tmp_clksrc; - - /* check to see if we're sourcing fclk, and if so we're - * going to have to update the clock source - */ - - if (strcmp(clkp->name, "fclk") == 0) { - struct s3c24xx_uart_clksrc src; - - s3c24xx_serial_getsource(port, &src); - - /* check that the port already using fclk, and if - * not, then re-select fclk - */ - - if (strcmp(src.name, clkp->name) == 0) { - s3c24xx_serial_setsource(port, clkp); - s3c24xx_serial_getsource(port, &src); - } - - clkp->divisor = src.divisor; - } - - s3c24xx_serial_calcbaud(res, port, clkp, baud); - best = res; - resptr = best + 1; - } else { - resptr = res; - - for (i = 0; i < cfg->clocks_size; i++, clkp++) { - if (s3c24xx_serial_calcbaud(resptr, port, clkp, baud)) - resptr++; - } - } - - /* ok, we now need to select the best clock we found */ - - if (!best) { - unsigned int deviation = (1<<30)|((1<<30)-1); - int calc_deviation; - - for (sptr = res; sptr < resptr; sptr++) { - printk(KERN_DEBUG - "found clk %p (%s) quot %d, calc %d\n", - sptr->clksrc, sptr->clksrc->name, - sptr->quot, sptr->calc); - - calc_deviation = baud - sptr->calc; - if (calc_deviation < 0) - calc_deviation = -calc_deviation; - - if (calc_deviation < deviation) { - best = sptr; - deviation = calc_deviation; - } - } - - printk(KERN_DEBUG "best %p (deviation %d)\n", best, deviation); - } - - printk(KERN_DEBUG "selected clock %p (%s) quot %d, calc %d\n", - best->clksrc, best->clksrc->name, best->quot, best->calc); - - /* store results to pass back */ - - *clksrc = best->clksrc; - *clk = best->src; - - return best->quot; -} - -static void s3c24xx_serial_set_termios(struct uart_port *port, - struct ktermios *termios, - struct ktermios *old) -{ - struct s3c2410_uartcfg *cfg = s3c24xx_port_to_cfg(port); - struct s3c24xx_uart_port *ourport = to_ourport(port); - struct s3c24xx_uart_clksrc *clksrc = NULL; - struct clk *clk = NULL; - unsigned long flags; - unsigned int baud, quot; - unsigned int ulcon; - unsigned int umcon; - - /* - * We don't support modem control lines. - */ - termios->c_cflag &= ~(HUPCL | CMSPAR); - termios->c_cflag |= CLOCAL; - - /* - * Ask the core to calculate the divisor for us. - */ - - baud = uart_get_baud_rate(port, termios, old, 0, 115200*8); - - if (baud == 38400 && (port->flags & UPF_SPD_MASK) == UPF_SPD_CUST) - quot = port->custom_divisor; - else - quot = s3c24xx_serial_getclk(port, &clksrc, &clk, baud); - - /* check to see if we need to change clock source */ - - if (ourport->clksrc != clksrc || ourport->baudclk != clk) { - s3c24xx_serial_setsource(port, clksrc); - - if (ourport->baudclk != NULL && !IS_ERR(ourport->baudclk)) { - clk_disable(ourport->baudclk); - ourport->baudclk = NULL; - } - - clk_enable(clk); - - ourport->clksrc = clksrc; - ourport->baudclk = clk; - } - - switch (termios->c_cflag & CSIZE) { - case CS5: - dbg("config: 5bits/char\n"); - ulcon = S3C2410_LCON_CS5; - break; - case CS6: - dbg("config: 6bits/char\n"); - ulcon = S3C2410_LCON_CS6; - break; - case CS7: - dbg("config: 7bits/char\n"); - ulcon = S3C2410_LCON_CS7; - break; - case CS8: - default: - dbg("config: 8bits/char\n"); - ulcon = S3C2410_LCON_CS8; - break; - } - - /* preserve original lcon IR settings */ - ulcon |= (cfg->ulcon & S3C2410_LCON_IRM); - - if (termios->c_cflag & CSTOPB) - ulcon |= S3C2410_LCON_STOPB; - - umcon = (termios->c_cflag & CRTSCTS) ? S3C2410_UMCOM_AFC : 0; - - if (termios->c_cflag & PARENB) { - if (termios->c_cflag & PARODD) - ulcon |= S3C2410_LCON_PODD; - else - ulcon |= S3C2410_LCON_PEVEN; - } else { - ulcon |= S3C2410_LCON_PNONE; - } - - spin_lock_irqsave(&port->lock, flags); - - dbg("setting ulcon to %08x, brddiv to %d\n", ulcon, quot); - - wr_regl(port, S3C2410_ULCON, ulcon); - wr_regl(port, S3C2410_UBRDIV, quot); - wr_regl(port, S3C2410_UMCON, umcon); - - dbg("uart: ulcon = 0x%08x, ucon = 0x%08x, ufcon = 0x%08x\n", - rd_regl(port, S3C2410_ULCON), - rd_regl(port, S3C2410_UCON), - rd_regl(port, S3C2410_UFCON)); - - /* - * Update the per-port timeout. - */ - uart_update_timeout(port, termios->c_cflag, baud); - - /* - * Which character status flags are we interested in? - */ - port->read_status_mask = S3C2410_UERSTAT_OVERRUN; - if (termios->c_iflag & INPCK) - port->read_status_mask |= S3C2410_UERSTAT_FRAME | S3C2410_UERSTAT_PARITY; - - /* - * Which character status flags should we ignore? - */ - port->ignore_status_mask = 0; - if (termios->c_iflag & IGNPAR) - port->ignore_status_mask |= S3C2410_UERSTAT_OVERRUN; - if (termios->c_iflag & IGNBRK && termios->c_iflag & IGNPAR) - port->ignore_status_mask |= S3C2410_UERSTAT_FRAME; - - /* - * Ignore all characters if CREAD is not set. - */ - if ((termios->c_cflag & CREAD) == 0) - port->ignore_status_mask |= RXSTAT_DUMMY_READ; - - spin_unlock_irqrestore(&port->lock, flags); -} - -static const char *s3c24xx_serial_type(struct uart_port *port) -{ - switch (port->type) { - case PORT_S3C2410: - return "S3C2410"; - case PORT_S3C2440: - return "S3C2440"; - case PORT_S3C2412: - return "S3C2412"; - default: - return NULL; - } -} - -#define MAP_SIZE (0x100) - -static void s3c24xx_serial_release_port(struct uart_port *port) -{ - release_mem_region(port->mapbase, MAP_SIZE); -} - -static int s3c24xx_serial_request_port(struct uart_port *port) -{ - const char *name = s3c24xx_serial_portname(port); - return request_mem_region(port->mapbase, MAP_SIZE, name) ? 0 : -EBUSY; -} - -static void s3c24xx_serial_config_port(struct uart_port *port, int flags) -{ - struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port); - - if (flags & UART_CONFIG_TYPE && - s3c24xx_serial_request_port(port) == 0) - port->type = info->type; -} - -/* - * verify the new serial_struct (for TIOCSSERIAL). - */ -static int -s3c24xx_serial_verify_port(struct uart_port *port, struct serial_struct *ser) -{ - struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port); - - if (ser->type != PORT_UNKNOWN && ser->type != info->type) - return -EINVAL; - - return 0; -} - - -#ifdef CONFIG_SERIAL_S3C2410_CONSOLE - -static struct console s3c24xx_serial_console; - -#define S3C24XX_SERIAL_CONSOLE &s3c24xx_serial_console -#else -#define S3C24XX_SERIAL_CONSOLE NULL -#endif - -static struct uart_ops s3c24xx_serial_ops = { - .pm = s3c24xx_serial_pm, - .tx_empty = s3c24xx_serial_tx_empty, - .get_mctrl = s3c24xx_serial_get_mctrl, - .set_mctrl = s3c24xx_serial_set_mctrl, - .stop_tx |