aboutsummaryrefslogtreecommitdiff
path: root/drivers/serial/ip22zilog.h
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/serial/ip22zilog.h')
-rw-r--r--drivers/serial/ip22zilog.h281
1 files changed, 0 insertions, 281 deletions
diff --git a/drivers/serial/ip22zilog.h b/drivers/serial/ip22zilog.h
deleted file mode 100644
index a59a9a8341d..00000000000
--- a/drivers/serial/ip22zilog.h
+++ /dev/null
@@ -1,281 +0,0 @@
-#ifndef _IP22_ZILOG_H
-#define _IP22_ZILOG_H
-
-#include <asm/byteorder.h>
-
-struct zilog_channel {
-#ifdef __BIG_ENDIAN
- volatile unsigned char unused0[3];
- volatile unsigned char control;
- volatile unsigned char unused1[3];
- volatile unsigned char data;
-#else /* __LITTLE_ENDIAN */
- volatile unsigned char control;
- volatile unsigned char unused0[3];
- volatile unsigned char data;
- volatile unsigned char unused1[3];
-#endif
-};
-
-struct zilog_layout {
- struct zilog_channel channelB;
- struct zilog_channel channelA;
-};
-
-#define NUM_ZSREGS 16
-
-/* Conversion routines to/from brg time constants from/to bits
- * per second.
- */
-#define BRG_TO_BPS(brg, freq) ((freq) / 2 / ((brg) + 2))
-#define BPS_TO_BRG(bps, freq) ((((freq) + (bps)) / (2 * (bps))) - 2)
-
-/* The Zilog register set */
-
-#define FLAG 0x7e
-
-/* Write Register 0 */
-#define R0 0 /* Register selects */
-#define R1 1
-#define R2 2
-#define R3 3
-#define R4 4
-#define R5 5
-#define R6 6
-#define R7 7
-#define R8 8
-#define R9 9
-#define R10 10
-#define R11 11
-#define R12 12
-#define R13 13
-#define R14 14
-#define R15 15
-
-#define NULLCODE 0 /* Null Code */
-#define POINT_HIGH 0x8 /* Select upper half of registers */
-#define RES_EXT_INT 0x10 /* Reset Ext. Status Interrupts */
-#define SEND_ABORT 0x18 /* HDLC Abort */
-#define RES_RxINT_FC 0x20 /* Reset RxINT on First Character */
-#define RES_Tx_P 0x28 /* Reset TxINT Pending */
-#define ERR_RES 0x30 /* Error Reset */
-#define RES_H_IUS 0x38 /* Reset highest IUS */
-
-#define RES_Rx_CRC 0x40 /* Reset Rx CRC Checker */
-#define RES_Tx_CRC 0x80 /* Reset Tx CRC Checker */
-#define RES_EOM_L 0xC0 /* Reset EOM latch */
-
-/* Write Register 1 */
-
-#define EXT_INT_ENAB 0x1 /* Ext Int Enable */
-#define TxINT_ENAB 0x2 /* Tx Int Enable */
-#define PAR_SPEC 0x4 /* Parity is special condition */
-
-#define RxINT_DISAB 0 /* Rx Int Disable */
-#define RxINT_FCERR 0x8 /* Rx Int on First Character Only or Error */
-#define INT_ALL_Rx 0x10 /* Int on all Rx Characters or error */
-#define INT_ERR_Rx 0x18 /* Int on error only */
-#define RxINT_MASK 0x18
-
-#define WT_RDY_RT 0x20 /* Wait/Ready on R/T */
-#define WT_FN_RDYFN 0x40 /* Wait/FN/Ready FN */
-#define WT_RDY_ENAB 0x80 /* Wait/Ready Enable */
-
-/* Write Register #2 (Interrupt Vector) */
-
-/* Write Register 3 */
-
-#define RxENAB 0x1 /* Rx Enable */
-#define SYNC_L_INH 0x2 /* Sync Character Load Inhibit */
-#define ADD_SM 0x4 /* Address Search Mode (SDLC) */
-#define RxCRC_ENAB 0x8 /* Rx CRC Enable */
-#define ENT_HM 0x10 /* Enter Hunt Mode */
-#define AUTO_ENAB 0x20 /* Auto Enables */
-#define Rx5 0x0 /* Rx 5 Bits/Character */
-#define Rx7 0x40 /* Rx 7 Bits/Character */
-#define Rx6 0x80 /* Rx 6 Bits/Character */
-#define Rx8 0xc0 /* Rx 8 Bits/Character */
-#define RxN_MASK 0xc0
-
-/* Write Register 4 */
-
-#define PAR_ENAB 0x1 /* Parity Enable */
-#define PAR_EVEN 0x2 /* Parity Even/Odd* */
-
-#define SYNC_ENAB 0 /* Sync Modes Enable */
-#define SB1 0x4 /* 1 stop bit/char */
-#define SB15 0x8 /* 1.5 stop bits/char */
-#define SB2 0xc /* 2 stop bits/char */
-
-#define MONSYNC 0 /* 8 Bit Sync character */
-#define BISYNC 0x10 /* 16 bit sync character */
-#define SDLC 0x20 /* SDLC Mode (01111110 Sync Flag) */
-#define EXTSYNC 0x30 /* External Sync Mode */
-
-#define X1CLK 0x0 /* x1 clock mode */
-#define X16CLK 0x40 /* x16 clock mode */
-#define X32CLK 0x80 /* x32 clock mode */
-#define X64CLK 0xC0 /* x64 clock mode */
-#define XCLK_MASK 0xC0
-
-/* Write Register 5 */
-
-#define TxCRC_ENAB 0x1 /* Tx CRC Enable */
-#define RTS 0x2 /* RTS */
-#define SDLC_CRC 0x4 /* SDLC/CRC-16 */
-#define TxENAB 0x8 /* Tx Enable */
-#define SND_BRK 0x10 /* Send Break */
-#define Tx5 0x0 /* Tx 5 bits (or less)/character */
-#define Tx7 0x20 /* Tx 7 bits/character */
-#define Tx6 0x40 /* Tx 6 bits/character */
-#define Tx8 0x60 /* Tx 8 bits/character */
-#define TxN_MASK 0x60
-#define DTR 0x80 /* DTR */
-
-/* Write Register 6 (Sync bits 0-7/SDLC Address Field) */
-
-/* Write Register 7 (Sync bits 8-15/SDLC 01111110) */
-
-/* Write Register 8 (transmit buffer) */
-
-/* Write Register 9 (Master interrupt control) */
-#define VIS 1 /* Vector Includes Status */
-#define NV 2 /* No Vector */
-#define DLC 4 /* Disable Lower Chain */
-#define MIE 8 /* Master Interrupt Enable */
-#define STATHI 0x10 /* Status high */
-#define NORESET 0 /* No reset on write to R9 */
-#define CHRB 0x40 /* Reset channel B */
-#define CHRA 0x80 /* Reset channel A */
-#define FHWRES 0xc0 /* Force hardware reset */
-
-/* Write Register 10 (misc control bits) */
-#define BIT6 1 /* 6 bit/8bit sync */
-#define LOOPMODE 2 /* SDLC Loop mode */
-#define ABUNDER 4 /* Abort/flag on SDLC xmit underrun */
-#define MARKIDLE 8 /* Mark/flag on idle */
-#define GAOP 0x10 /* Go active on poll */
-#define NRZ 0 /* NRZ mode */
-#define NRZI 0x20 /* NRZI mode */
-#define FM1 0x40 /* FM1 (transition = 1) */
-#define FM0 0x60 /* FM0 (transition = 0) */
-#define CRCPS 0x80 /* CRC Preset I/O */
-
-/* Write Register 11 (Clock Mode control) */
-#define TRxCXT 0 /* TRxC = Xtal output */
-#define TRxCTC 1 /* TRxC = Transmit clock */
-#define TRxCBR 2 /* TRxC = BR Generator Output */
-#define TRxCDP 3 /* TRxC = DPLL output */
-#define TRxCOI 4 /* TRxC O/I */
-#define TCRTxCP 0 /* Transmit clock = RTxC pin */
-#define TCTRxCP 8 /* Transmit clock = TRxC pin */
-#define TCBR 0x10 /* Transmit clock = BR Generator output */
-#define TCDPLL 0x18 /* Transmit clock = DPLL output */
-#define RCRTxCP 0 /* Receive clock = RTxC pin */
-#define RCTRxCP 0x20 /* Receive clock = TRxC pin */
-#define RCBR 0x40 /* Receive clock = BR Generator output */
-#define RCDPLL 0x60 /* Receive clock = DPLL output */
-#define RTxCX 0x80 /* RTxC Xtal/No Xtal */
-
-/* Write Register 12 (lower byte of baud rate generator time constant) */
-
-/* Write Register 13 (upper byte of baud rate generator time constant) */
-
-/* Write Register 14 (Misc control bits) */
-#define BRENAB 1 /* Baud rate generator enable */
-#define BRSRC 2 /* Baud rate generator source */
-#define DTRREQ 4 /* DTR/Request function */
-#define AUTOECHO 8 /* Auto Echo */
-#define LOOPBAK 0x10 /* Local loopback */
-#define SEARCH 0x20 /* Enter search mode */
-#define RMC 0x40 /* Reset missing clock */
-#define DISDPLL 0x60 /* Disable DPLL */
-#define SSBR 0x80 /* Set DPLL source = BR generator */
-#define SSRTxC 0xa0 /* Set DPLL source = RTxC */
-#define SFMM 0xc0 /* Set FM mode */
-#define SNRZI 0xe0 /* Set NRZI mode */
-
-/* Write Register 15 (external/status interrupt control) */
-#define ZCIE 2 /* Zero count IE */
-#define DCDIE 8 /* DCD IE */
-#define SYNCIE 0x10 /* Sync/hunt IE */
-#define CTSIE 0x20 /* CTS IE */
-#define TxUIE 0x40 /* Tx Underrun/EOM IE */
-#define BRKIE 0x80 /* Break/Abort IE */
-
-
-/* Read Register 0 */
-#define Rx_CH_AV 0x1 /* Rx Character Available */
-#define ZCOUNT 0x2 /* Zero count */
-#define Tx_BUF_EMP 0x4 /* Tx Buffer empty */
-#define DCD 0x8 /* DCD */
-#define SYNC 0x10 /* Sync/hunt */
-#define CTS 0x20 /* CTS */
-#define TxEOM 0x40 /* Tx underrun */
-#define BRK_ABRT 0x80 /* Break/Abort */
-
-/* Read Register 1 */
-#define ALL_SNT 0x1 /* All sent */
-/* Residue Data for 8 Rx bits/char programmed */
-#define RES3 0x8 /* 0/3 */
-#define RES4 0x4 /* 0/4 */
-#define RES5 0xc /* 0/5 */
-#define RES6 0x2 /* 0/6 */
-#define RES7 0xa /* 0/7 */
-#define RES8 0x6 /* 0/8 */
-#define RES18 0xe /* 1/8 */
-#define RES28 0x0 /* 2/8 */
-/* Special Rx Condition Interrupts */
-#define PAR_ERR 0x10 /* Parity error */
-#define Rx_OVR 0x20 /* Rx Overrun Error */
-#define CRC_ERR 0x40 /* CRC/Framing Error */
-#define END_FR 0x80 /* End of Frame (SDLC) */
-
-/* Read Register 2 (channel b only) - Interrupt vector */
-#define CHB_Tx_EMPTY 0x00
-#define CHB_EXT_STAT 0x02
-#define CHB_Rx_AVAIL 0x04
-#define CHB_SPECIAL 0x06
-#define CHA_Tx_EMPTY 0x08
-#define CHA_EXT_STAT 0x0a
-#define CHA_Rx_AVAIL 0x0c
-#define CHA_SPECIAL 0x0e
-#define STATUS_MASK 0x0e
-
-/* Read Register 3 (interrupt pending register) ch a only */
-#define CHBEXT 0x1 /* Channel B Ext/Stat IP */
-#define CHBTxIP 0x2 /* Channel B Tx IP */
-#define CHBRxIP 0x4 /* Channel B Rx IP */
-#define CHAEXT 0x8 /* Channel A Ext/Stat IP */
-#define CHATxIP 0x10 /* Channel A Tx IP */
-#define CHARxIP 0x20 /* Channel A Rx IP */
-
-/* Read Register 8 (receive data register) */
-
-/* Read Register 10 (misc status bits) */
-#define ONLOOP 2 /* On loop */
-#define LOOPSEND 0x10 /* Loop sending */
-#define CLK2MIS 0x40 /* Two clocks missing */
-#define CLK1MIS 0x80 /* One clock missing */
-
-/* Read Register 12 (lower byte of baud rate generator constant) */
-
-/* Read Register 13 (upper byte of baud rate generator constant) */
-
-/* Read Register 15 (value of WR 15) */
-
-/* Misc macros */
-#define ZS_CLEARERR(channel) do { writeb(ERR_RES, &channel->control); \
- udelay(5); } while(0)
-
-#define ZS_CLEARSTAT(channel) do { writeb(RES_EXT_INT, &channel->control); \
- udelay(5); } while(0)
-
-#define ZS_CLEARFIFO(channel) do { readb(&channel->data); \
- udelay(2); \
- readb(&channel->data); \
- udelay(2); \
- readb(&channel->data); \
- udelay(2); } while(0)
-
-#endif /* _IP22_ZILOG_H */
generated by cgit v1.2.3-18-g5258 (git 2.32.0) at 2024-12-21 08:21:09 +0000