diff options
Diffstat (limited to 'drivers/serial/68360serial.c')
| -rw-r--r-- | drivers/serial/68360serial.c | 2978 |
1 files changed, 0 insertions, 2978 deletions
diff --git a/drivers/serial/68360serial.c b/drivers/serial/68360serial.c deleted file mode 100644 index 88b13356ec1..00000000000 --- a/drivers/serial/68360serial.c +++ /dev/null @@ -1,2978 +0,0 @@ -/* - * UART driver for 68360 CPM SCC or SMC - * Copyright (c) 2000 D. Jeff Dionne <jeff@uclinux.org>, - * Copyright (c) 2000 Michael Leslie <mleslie@lineo.ca> - * Copyright (c) 1997 Dan Malek <dmalek@jlc.net> - * - * I used the serial.c driver as the framework for this driver. - * Give credit to those guys. - * The original code was written for the MBX860 board. I tried to make - * it generic, but there may be some assumptions in the structures that - * have to be fixed later. - * To save porting time, I did not bother to change any object names - * that are not accessed outside of this file. - * It still needs lots of work........When it was easy, I included code - * to support the SCCs, but this has never been tested, nor is it complete. - * Only the SCCs support modem control, so that is not complete either. - * - * This module exports the following rs232 io functions: - * - * int rs_360_init(void); - */ - -#include <linux/module.h> -#include <linux/errno.h> -#include <linux/signal.h> -#include <linux/sched.h> -#include <linux/timer.h> -#include <linux/interrupt.h> -#include <linux/tty.h> -#include <linux/tty_flip.h> -#include <linux/serial.h> -#include <linux/serialP.h> -#include <linux/major.h> -#include <linux/string.h> -#include <linux/fcntl.h> -#include <linux/ptrace.h> -#include <linux/mm.h> -#include <linux/init.h> -#include <linux/delay.h> -#include <asm/irq.h> -#include <asm/m68360.h> -#include <asm/commproc.h> - - -#ifdef CONFIG_KGDB -extern void breakpoint(void); -extern void set_debug_traps(void); -extern int kgdb_output_string (const char* s, unsigned int count); -#endif - - -/* #ifdef CONFIG_SERIAL_CONSOLE */ /* This seems to be a post 2.0 thing - mles */ -#include <linux/console.h> -#include <linux/jiffies.h> - -/* this defines the index into rs_table for the port to use - */ -#ifndef CONFIG_SERIAL_CONSOLE_PORT -#define CONFIG_SERIAL_CONSOLE_PORT 1 /* ie SMC2 - note USE_SMC2 must be defined */ -#endif -/* #endif */ - -#if 0 -/* SCC2 for console - */ -#undef CONFIG_SERIAL_CONSOLE_PORT -#define CONFIG_SERIAL_CONSOLE_PORT 2 -#endif - - -#define TX_WAKEUP ASYNC_SHARE_IRQ - -static char *serial_name = "CPM UART driver"; -static char *serial_version = "0.03"; - -static struct tty_driver *serial_driver; -int serial_console_setup(struct console *co, char *options); - -/* - * Serial driver configuration section. Here are the various options: - */ -#define SERIAL_PARANOIA_CHECK -#define CONFIG_SERIAL_NOPAUSE_IO -#define SERIAL_DO_RESTART - -/* Set of debugging defines */ - -#undef SERIAL_DEBUG_INTR -#undef SERIAL_DEBUG_OPEN -#undef SERIAL_DEBUG_FLOW -#undef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT - -#define _INLINE_ inline - -#define DBG_CNT(s) - -/* We overload some of the items in the data structure to meet our - * needs. For example, the port address is the CPM parameter ram - * offset for the SCC or SMC. The maximum number of ports is 4 SCCs and - * 2 SMCs. The "hub6" field is used to indicate the channel number, with - * a flag indicating SCC or SMC, and the number is used as an index into - * the CPM parameter area for this device. - * The "type" field is currently set to 0, for PORT_UNKNOWN. It is - * not currently used. I should probably use it to indicate the port - * type of SMC or SCC. - * The SMCs do not support any modem control signals. - */ -#define smc_scc_num hub6 -#define NUM_IS_SCC ((int)0x00010000) -#define PORT_NUM(P) ((P) & 0x0000ffff) - - -#if defined (CONFIG_UCQUICC) - -volatile extern void *_periph_base; -/* sipex transceiver - * mode bits for are on pins - * - * SCC2 d16..19 - * SCC3 d20..23 - * SCC4 d24..27 - */ -#define SIPEX_MODE(n,m) ((m & 0x0f)<<(16+4*(n-1))) - -static uint sipex_mode_bits = 0x00000000; - -#endif - -/* There is no `serial_state' defined back here in 2.0. - * Try to get by with serial_struct - */ -/* #define serial_state serial_struct */ - -/* 2.4 -> 2.0 portability problem: async_icount in 2.4 has a few - * extras: */ - -#if 0 -struct async_icount_24 { - __u32 cts, dsr, rng, dcd, tx, rx; - __u32 frame, parity, overrun, brk; - __u32 buf_overrun; -} icount; -#endif - -#if 0 - -struct serial_state { - int magic; - int baud_base; - unsigned long port; - int irq; - int flags; - int hub6; - int type; - int line; - int revision; /* Chip revision (950) */ - int xmit_fifo_size; - int custom_divisor; - int count; - u8 *iomem_base; - u16 iomem_reg_shift; - unsigned short close_delay; - unsigned short closing_wait; /* time to wait before closing */ - struct async_icount_24 icount; - int io_type; - struct async_struct *info; -}; -#endif - -#define SSTATE_MAGIC 0x5302 - - - -/* SMC2 is sometimes used for low performance TDM interfaces. Define - * this as 1 if you want SMC2 as a serial port UART managed by this driver. - * Define this as 0 if you wish to use SMC2 for something else. - */ -#define USE_SMC2 1 - -#if 0 -/* Define SCC to ttySx mapping. */ -#define SCC_NUM_BASE (USE_SMC2 + 1) /* SCC base tty "number" */ - -/* Define which SCC is the first one to use for a serial port. These - * are 0-based numbers, i.e. this assumes the first SCC (SCC1) is used - * for Ethernet, and the first available SCC for serial UART is SCC2. - * NOTE: IF YOU CHANGE THIS, you have to change the PROFF_xxx and - * interrupt vectors in the table below to match. - */ -#define SCC_IDX_BASE 1 /* table index */ -#endif - - -/* Processors other than the 860 only get SMCs configured by default. - * Either they don't have SCCs or they are allocated somewhere else. - * Of course, there are now 860s without some SCCs, so we will need to - * address that someday. - * The Embedded Planet Multimedia I/O cards use TDM interfaces to the - * stereo codec parts, and we use SMC2 to help support that. - */ -static struct serial_state rs_table[] = { -/* type line PORT IRQ FLAGS smc_scc_num (F.K.A. hub6) */ - { 0, 0, PRSLOT_SMC1, CPMVEC_SMC1, 0, 0 } /* SMC1 ttyS0 */ -#if USE_SMC2 - ,{ 0, 0, PRSLOT_SMC2, CPMVEC_SMC2, 0, 1 } /* SMC2 ttyS1 */ -#endif - -#if defined(CONFIG_SERIAL_68360_SCC) - ,{ 0, 0, PRSLOT_SCC2, CPMVEC_SCC2, 0, (NUM_IS_SCC | 1) } /* SCC2 ttyS2 */ - ,{ 0, 0, PRSLOT_SCC3, CPMVEC_SCC3, 0, (NUM_IS_SCC | 2) } /* SCC3 ttyS3 */ - ,{ 0, 0, PRSLOT_SCC4, CPMVEC_SCC4, 0, (NUM_IS_SCC | 3) } /* SCC4 ttyS4 */ -#endif -}; - -#define NR_PORTS (sizeof(rs_table)/sizeof(struct serial_state)) - -/* The number of buffer descriptors and their sizes. - */ -#define RX_NUM_FIFO 4 -#define RX_BUF_SIZE 32 -#define TX_NUM_FIFO 4 -#define TX_BUF_SIZE 32 - -#define CONSOLE_NUM_FIFO 2 -#define CONSOLE_BUF_SIZE 4 - -char *console_fifos[CONSOLE_NUM_FIFO * CONSOLE_BUF_SIZE]; - -/* The async_struct in serial.h does not really give us what we - * need, so define our own here. - */ -typedef struct serial_info { - int magic; - int flags; - - struct serial_state *state; - /* struct serial_struct *state; */ - /* struct async_struct *state; */ - - struct tty_struct *tty; - int read_status_mask; - int ignore_status_mask; - int timeout; - int line; - int x_char; /* xon/xoff character */ - int close_delay; - unsigned short closing_wait; - unsigned short closing_wait2; - unsigned long event; - unsigned long last_active; - int blocked_open; /* # of blocked opens */ - struct work_struct tqueue; - struct work_struct tqueue_hangup; - wait_queue_head_t open_wait; - wait_queue_head_t close_wait; - - -/* CPM Buffer Descriptor pointers. - */ - QUICC_BD *rx_bd_base; - QUICC_BD *rx_cur; - QUICC_BD *tx_bd_base; - QUICC_BD *tx_cur; -} ser_info_t; - - -/* since kmalloc_init() does not get called until much after this initialization: */ -static ser_info_t quicc_ser_info[NR_PORTS]; -static char rx_buf_pool[NR_PORTS * RX_NUM_FIFO * RX_BUF_SIZE]; -static char tx_buf_pool[NR_PORTS * TX_NUM_FIFO * TX_BUF_SIZE]; - -static void change_speed(ser_info_t *info); -static void rs_360_wait_until_sent(struct tty_struct *tty, int timeout); - -static inline int serial_paranoia_check(ser_info_t *info, - char *name, const char *routine) -{ -#ifdef SERIAL_PARANOIA_CHECK - static const char *badmagic = - "Warning: bad magic number for serial struct (%s) in %s\n"; - static const char *badinfo = - "Warning: null async_struct for (%s) in %s\n"; - - if (!info) { - printk(badinfo, name, routine); - return 1; - } - if (info->magic != SERIAL_MAGIC) { - printk(badmagic, name, routine); - return 1; - } -#endif - return 0; -} - -/* - * This is used to figure out the divisor speeds and the timeouts, - * indexed by the termio value. The generic CPM functions are responsible - * for setting and assigning baud rate generators for us. - */ -static int baud_table[] = { - 0, 50, 75, 110, 134, 150, 200, 300, 600, 1200, 1800, 2400, 4800, - 9600, 19200, 38400, 57600, 115200, 230400, 460800, 0 }; - -/* This sucks. There is a better way: */ -#if defined(CONFIG_CONSOLE_9600) - #define CONSOLE_BAUDRATE 9600 -#elif defined(CONFIG_CONSOLE_19200) - #define CONSOLE_BAUDRATE 19200 -#elif defined(CONFIG_CONSOLE_115200) - #define CONSOLE_BAUDRATE 115200 -#else - #warning "console baud rate undefined" - #define CONSOLE_BAUDRATE 9600 -#endif - -/* - * ------------------------------------------------------------ - * rs_stop() and rs_start() - * - * This routines are called before setting or resetting tty->stopped. - * They enable or disable transmitter interrupts, as necessary. - * ------------------------------------------------------------ - */ -static void rs_360_stop(struct tty_struct *tty) -{ - ser_info_t *info = (ser_info_t *)tty->driver_data; - int idx; - unsigned long flags; - volatile struct scc_regs *sccp; - volatile struct smc_regs *smcp; - - if (serial_paranoia_check(info, tty->name, "rs_stop")) - return; - - local_irq_save(flags); - idx = PORT_NUM(info->state->smc_scc_num); - if (info->state->smc_scc_num & NUM_IS_SCC) { - sccp = &pquicc->scc_regs[idx]; - sccp->scc_sccm &= ~UART_SCCM_TX; - } else { - /* smcp = &cpmp->cp_smc[idx]; */ - smcp = &pquicc->smc_regs[idx]; - smcp->smc_smcm &= ~SMCM_TX; - } - local_irq_restore(flags); -} - - -static void rs_360_start(struct tty_struct *tty) -{ - ser_info_t *info = (ser_info_t *)tty->driver_data; - int idx; - unsigned long flags; - volatile struct scc_regs *sccp; - volatile struct smc_regs *smcp; - - if (serial_paranoia_check(info, tty->name, "rs_stop")) - return; - - local_irq_save(flags); - idx = PORT_NUM(info->state->smc_scc_num); - if (info->state->smc_scc_num & NUM_IS_SCC) { - sccp = &pquicc->scc_regs[idx]; - sccp->scc_sccm |= UART_SCCM_TX; - } else { - smcp = &pquicc->smc_regs[idx]; - smcp->smc_smcm |= SMCM_TX; - } - local_irq_restore(flags); -} - -/* - * ---------------------------------------------------------------------- - * - * Here starts the interrupt handling routines. All of the following - * subroutines are declared as inline and are folded into - * rs_interrupt(). They were separated out for readability's sake. - * - * Note: rs_interrupt() is a "fast" interrupt, which means that it - * runs with interrupts turned off. People who may want to modify - * rs_interrupt() should try to keep the interrupt handler as fast as - * possible. After you are done making modifications, it is not a bad - * idea to do: - * - * gcc -S -DKERNEL -Wall -Wstrict-prototypes -O6 -fomit-frame-pointer serial.c - * - * and look at the resulting assemble code in serial.s. - * - * - Ted Ts'o (tytso@mit.edu), 7-Mar-93 - * ----------------------------------------------------------------------- - */ - -static _INLINE_ void receive_chars(ser_info_t *info) -{ - struct tty_struct *tty = info->port.tty; - unsigned char ch, flag, *cp; - /*int ignored = 0;*/ - int i; - ushort status; - struct async_icount *icount; - /* struct async_icount_24 *icount; */ - volatile QUICC_BD *bdp; - - icount = &info->state->icount; - - /* Just loop through the closed BDs and copy the characters into - * the buffer. - */ - bdp = info->rx_cur; - for (;;) { - if (bdp->status & BD_SC_EMPTY) /* If this one is empty */ - break; /* we are all done */ - - /* The read status mask tell us what we should do with - * incoming characters, especially if errors occur. - * One special case is the use of BD_SC_EMPTY. If - * this is not set, we are supposed to be ignoring - * inputs. In this case, just mark the buffer empty and - * continue. - */ - if (!(info->read_status_mask & BD_SC_EMPTY)) { - bdp->status |= BD_SC_EMPTY; - bdp->status &= - ~(BD_SC_BR | BD_SC_FR | BD_SC_PR | BD_SC_OV); - - if (bdp->status & BD_SC_WRAP) - bdp = info->rx_bd_base; - else - bdp++; - continue; - } - - /* Get the number of characters and the buffer pointer. - */ - i = bdp->length; - /* cp = (unsigned char *)__va(bdp->buf); */ - cp = (char *)bdp->buf; - status = bdp->status; - - while (i-- > 0) { - ch = *cp++; - icount->rx++; - -#ifdef SERIAL_DEBUG_INTR - printk("DR%02x:%02x...", ch, status); -#endif - flag = TTY_NORMAL; - - if (status & (BD_SC_BR | BD_SC_FR | - BD_SC_PR | BD_SC_OV)) { - /* - * For statistics only - */ - if (status & BD_SC_BR) - icount->brk++; - else if (status & BD_SC_PR) - icount->parity++; - else if (status & BD_SC_FR) - icount->frame++; - if (status & BD_SC_OV) - icount->overrun++; - - /* - * Now check to see if character should be - * ignored, and mask off conditions which - * should be ignored. - if (status & info->ignore_status_mask) { - if (++ignored > 100) - break; - continue; - } - */ - status &= info->read_status_mask; - - if (status & (BD_SC_BR)) { -#ifdef SERIAL_DEBUG_INTR - printk("handling break...."); -#endif - *tty->flip.flag_buf_ptr = TTY_BREAK; - if (info->flags & ASYNC_SAK) - do_SAK(tty); - } else if (status & BD_SC_PR) - flag = TTY_PARITY; - else if (status & BD_SC_FR) - flag = TTY_FRAME; - } - tty_insert_flip_char(tty, ch, flag); - if (status & BD_SC_OV) - /* - * Overrun is special, since it's - * reported immediately, and doesn't - * affect the current character - */ - tty_insert_flip_char(tty, 0, TTY_OVERRUN); - } - - /* This BD is ready to be used again. Clear status. - * Get next BD. - */ - bdp->status |= BD_SC_EMPTY; - bdp->status &= ~(BD_SC_BR | BD_SC_FR | BD_SC_PR | BD_SC_OV); - - if (bdp->status & BD_SC_WRAP) - bdp = info->rx_bd_base; - else - bdp++; - } - - info->rx_cur = (QUICC_BD *)bdp; - - tty_schedule_flip(tty); -} - -static _INLINE_ void receive_break(ser_info_t *info) -{ - struct tty_struct *tty = info->port.tty; - - info->state->icount.brk++; - /* Check to see if there is room in the tty buffer for - * the break. If not, we exit now, losing the break. FIXME - */ - tty_insert_flip_char(tty, 0, TTY_BREAK); - tty_schedule_flip(tty); -} - -static _INLINE_ void transmit_chars(ser_info_t *info) -{ - - if ((info->flags & TX_WAKEUP) || - (info->port.tty->flags & (1 << TTY_DO_WRITE_WAKEUP))) { - schedule_work(&info->tqueue); - } - -#ifdef SERIAL_DEBUG_INTR - printk("THRE..."); -#endif -} - -#ifdef notdef - /* I need to do this for the SCCs, so it is left as a reminder. - */ -static _INLINE_ void check_modem_status(struct async_struct *info) -{ - int status; - /* struct async_icount *icount; */ - struct async_icount_24 *icount; - - status = serial_in(info, UART_MSR); - - if (status & UART_MSR_ANY_DELTA) { - icount = &info->state->icount; - /* update input line counters */ - if (status & UART_MSR_TERI) - icount->rng++; - if (status & UART_MSR_DDSR) - icount->dsr++; - if (status & UART_MSR_DDCD) { - icount->dcd++; -#ifdef CONFIG_HARD_PPS - if ((info->flags & ASYNC_HARDPPS_CD) && - (status & UART_MSR_DCD)) - hardpps(); -#endif - } - if (status & UART_MSR_DCTS) - icount->cts++; - wake_up_interruptible(&info->delta_msr_wait); - } - - if ((info->flags & ASYNC_CHECK_CD) && (status & UART_MSR_DDCD)) { -#if (defined(SERIAL_DEBUG_OPEN) || defined(SERIAL_DEBUG_INTR)) - printk("ttys%d CD now %s...", info->line, - (status & UART_MSR_DCD) ? "on" : "off"); -#endif - if (status & UART_MSR_DCD) - wake_up_interruptible(&info->open_wait); - else { -#ifdef SERIAL_DEBUG_OPEN - printk("scheduling hangup..."); -#endif - queue_task(&info->tqueue_hangup, - &tq_scheduler); - } - } - if (info->flags & ASYNC_CTS_FLOW) { - if (info->port.tty->hw_stopped) { - if (status & UART_MSR_CTS) { -#if (defined(SERIAL_DEBUG_INTR) || defined(SERIAL_DEBUG_FLOW)) - printk("CTS tx start..."); -#endif - info->port.tty->hw_stopped = 0; - info->IER |= UART_IER_THRI; - serial_out(info, UART_IER, info->IER); - rs_sched_event(info, RS_EVENT_WRITE_WAKEUP); - return; - } - } else { - if (!(status & UART_MSR_CTS)) { -#if (defined(SERIAL_DEBUG_INTR) || defined(SERIAL_DEBUG_FLOW)) - printk("CTS tx stop..."); -#endif - info->port.tty->hw_stopped = 1; - info->IER &= ~UART_IER_THRI; - serial_out(info, UART_IER, info->IER); - } - } - } -} -#endif - -/* - * This is the serial driver's interrupt routine for a single port - */ -/* static void rs_360_interrupt(void *dev_id) */ /* until and if we start servicing irqs here */ -static void rs_360_interrupt(int vec, void *dev_id) -{ - u_char events; - int idx; - ser_info_t *info; - volatile struct smc_regs *smcp; - volatile struct scc_regs *sccp; - - info = dev_id; - - idx = PORT_NUM(info->state->smc_scc_num); - if (info->state->smc_scc_num & NUM_IS_SCC) { - sccp = &pquicc->scc_regs[idx]; - events = sccp->scc_scce; - if (events & SCCM_RX) - receive_chars(info); - if (events & SCCM_TX) - transmit_chars(info); - sccp->scc_scce = events; - } else { - smcp = &pquicc->smc_regs[idx]; - events = smcp->smc_smce; - if (events & SMCM_BRKE) - receive_break(info); - if (events & SMCM_RX) - receive_chars(info); - if (events & SMCM_TX) - transmit_chars(info); - smcp->smc_smce = events; - } - -#ifdef SERIAL_DEBUG_INTR - printk("rs_interrupt_single(%d, %x)...", - info->state->smc_scc_num, events); -#endif -#ifdef modem_control - check_modem_status(info); -#endif - info->last_active = jiffies; -#ifdef SERIAL_DEBUG_INTR - printk("end.\n"); -#endif -} - - -/* - * ------------------------------------------------------------------- - * Here ends the serial interrupt routines. - * ------------------------------------------------------------------- - */ - - -static void do_softint(void *private_) -{ - ser_info_t *info = (ser_info_t *) private_; - struct tty_struct *tty; - - tty = info->port.tty; - if (!tty) - return; - - if (test_and_clear_bit(RS_EVENT_WRITE_WAKEUP, &info->event)) - tty_wakeup(tty); -} - - -/* - * This routine is called from the scheduler tqueue when the interrupt - * routine has signalled that a hangup has occurred. The path of - * hangup processing is: - * - * serial interrupt routine -> (scheduler tqueue) -> - * do_serial_hangup() -> tty->hangup() -> rs_hangup() - * - */ -static void do_serial_hangup(void *private_) -{ - struct async_struct *info = (struct async_struct *) private_; - struct tty_struct *tty; - - tty = info->port.tty; - if (!tty) - return; - - tty_hangup(tty); -} - - -static int startup(ser_info_t *info) -{ - unsigned long flags; - int retval=0; - int idx; - /*struct serial_state *state = info->state;*/ - volatile struct smc_regs *smcp; - volatile struct scc_regs *sccp; - volatile struct smc_uart_pram *up; - volatile struct uart_pram *scup; - - - local_irq_save(flags); - - if (info->flags & ASYNC_INITIALIZED) { - goto errout; - } - -#ifdef maybe - if (!state->port || !state->type) { - if (info->port.tty) - set_bit(TTY_IO_ERROR, &info->port.tty->flags); - goto errout; - } -#endif - -#ifdef SERIAL_DEBUG_OPEN - printk("starting up ttys%d (irq %d)...", info->line, state->irq); -#endif - - -#ifdef modem_control - info->MCR = 0; - if (info->port.tty->termios->c_cflag & CBAUD) - info->MCR = UART_MCR_DTR | UART_MCR_RTS; -#endif - - if (info->port.tty) - clear_bit(TTY_IO_ERROR, &info->port.tty->flags); - - /* - * and set the speed of the serial port - */ - change_speed(info); - - idx = PORT_NUM(info->state->smc_scc_num); - if (info->state->smc_scc_num & NUM_IS_SCC) { - sccp = &pquicc->scc_regs[idx]; - scup = &pquicc->pram[info->state->port].scc.pscc.u; - - scup->mrblr = RX_BUF_SIZE; - scup->max_idl = RX_BUF_SIZE; - - sccp->scc_sccm |= (UART_SCCM_TX | UART_SCCM_RX); - sccp->scc_gsmr.w.low |= (SCC_GSMRL_ENR | SCC_GSMRL_ENT); - - } else { - smcp = &pquicc->smc_regs[idx]; - - /* Enable interrupts and I/O. - */ - smcp->smc_smcm |= (SMCM_RX | SMCM_TX); - smcp->smc_smcmr |= (SMCMR_REN | SMCMR_TEN); - - /* We can tune the buffer length and idle characters - * to take advantage of the entire incoming buffer size. - * If mrblr is something other than 1, maxidl has to be - * non-zero or we never get an interrupt. The maxidl - * is the number of character times we wait after reception - * of the last character before we decide no more characters - * are coming. - */ - /* up = (smc_uart_t *)&pquicc->cp_dparam[state->port]; */ - /* holy unionized structures, Batman: */ - up = &pquicc->pram[info->state->port].scc.pothers.idma_smc.psmc.u; - - up->mrblr = RX_BUF_SIZE; - up->max_idl = RX_BUF_SIZE; - - up->brkcr = 1; /* number of break chars */ - } - - info->flags |= ASYNC_INITIALIZED; - local_irq_restore(flags); - return 0; - -errout: - local_irq_restore(flags); - return retval; -} - -/* - * This routine will shutdown a serial port; interrupts are disabled, and - * DTR is dropped if the hangup on close termio flag is on. - */ -static void shutdown(ser_info_t *info) -{ - unsigned long flags; - struct serial_state *state; - int idx; - volatile struct smc_regs *smcp; - volatile struct scc_regs *sccp; - - if (!(info->flags & ASYNC_INITIALIZED)) - return; - - state = info->state; - -#ifdef SERIAL_DEBUG_OPEN - printk("Shutting down serial port %d (irq %d)....", info->line, - state->irq); -#endif - - local_irq_save(flags); - - idx = PORT_NUM(state->smc_scc_num); - if (state->smc_scc_num & NUM_IS_SCC) { - sccp = &pquicc->scc_regs[idx]; - sccp->scc_gsmr.w.low &= ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT); -#ifdef CONFIG_SERIAL_CONSOLE - /* We can't disable the transmitter if this is the - * system console. - */ - if ((state - rs_table) != CONFIG_SERIAL_CONSOLE_PORT) -#endif - sccp->scc_sccm &= ~(UART_SCCM_TX | UART_SCCM_RX); - } else { - smcp = &pquicc->smc_regs[idx]; - - /* Disable interrupts and I/O. - */ - smcp->smc_smcm &= ~(SMCM_RX | SMCM_TX); -#ifdef CONFIG_SERIAL_CONSOLE - /* We can't disable the transmitter if this is the - * system console. - */ - if ((state - rs_table) != CONFIG_SERIAL_CONSOLE_PORT) -#endif - smcp->smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN); - } - - if (info->port.tty) - set_bit(TTY_IO_ERROR, &info->port.tty->flags); - - info->flags &= ~ASYNC_INITIALIZED; - local_irq_restore(flags); -} - -/* - * This routine is called to set the UART divisor registers to match - * the specified baud rate for a serial port. - */ -static void change_speed(ser_info_t *info) -{ - int baud_rate; - unsigned cflag, cval, scval, prev_mode; - int i, bits, sbits, idx; - unsigned long flags; - struct serial_state *state; - volatile struct smc_regs *smcp; - volatile struct scc_regs *sccp; - - if (!info->port.tty || !info->port.tty->termios) - return; - cflag = info->port.tty->termios->c_cflag; - - state = info->state; - - /* Character length programmed into the mode register is the - * sum of: 1 start bit, number of data bits, 0 or 1 parity bit, - * 1 or 2 stop bits, minus 1. - * The value 'bits' counts this for us. - */ - cval = 0; - scval = 0; - - /* byte size and parity */ - switch (cflag & CSIZE) { - case CS5: bits = 5; break; - case CS6: bits = 6; break; - case CS7: bits = 7; break; - case CS8: bits = 8; break; - /* Never happens, but GCC is too dumb to figure it out */ - default: bits = 8; break; - } - sbits = bits - 5; - - if (cflag & CSTOPB) { - cval |= SMCMR_SL; /* Two stops */ - scval |= SCU_PMSR_SL; - bits++; - } - if (cflag & PARENB) { - cval |= SMCMR_PEN; - scval |= SCU_PMSR_PEN; - bits++; - } - if (!(cflag & PARODD)) { - cval |= SMCMR_PM_EVEN; - scval |= (SCU_PMSR_REVP | SCU_PMSR_TEVP); - } - - /* Determine divisor based on baud rate */ - i = cflag & CBAUD; - if (i >= (sizeof(baud_table)/sizeof(int))) - baud_rate = 9600; - else - baud_rate = baud_table[i]; - - info->timeout = (TX_BUF_SIZE*HZ*bits); - info->timeout += HZ/50; /* Add .02 seconds of slop */ - -#ifdef modem_control - /* CTS flow control flag and modem status interrupts */ - info->IER &= ~UART_IER_MSI; - if (info->flags & ASYNC_HARDPPS_CD) - info->IER |= UART_IER_MSI; - if (cflag & CRTSCTS) { - info->flags |= ASYNC_CTS_FLOW; - info->IER |= UART_IER_MSI; - } else - info->flags &= ~ASYNC_CTS_FLOW; - if (cflag & CLOCAL) - info->flags &= ~ASYNC_CHECK_CD; - else { - info->flags |= ASYNC_CHECK_CD; - info->IER |= UART_IER_MSI; - } - serial_out(info, UART_IER, info->IER); -#endif - - /* - * Set up parity check flag - */ - info->read_status_mask = (BD_SC_EMPTY | BD_SC_OV); - if (I_INPCK(info->port.tty)) - info->read_status_mask |= BD_SC_FR | BD_SC_PR; - if (I_BRKINT(info->port.tty) || I_PARMRK(info->port.tty)) - info->read_status_mask |= BD_SC_BR; - - /* - * Characters to ignore - */ - info->ignore_status_mask = 0; - if (I_IGNPAR(info->port.tty)) - info->ignore_status_mask |= BD_SC_PR | BD_SC_FR; - if (I_IGNBRK(info->port.tty)) { - info->ignore_status_mask |= BD_SC_BR; - /* - * If we're ignore parity and break indicators, ignore - * overruns too. (For real raw support). - */ - if (I_IGNPAR(info->port.tty)) - info->ignore_status_mask |= BD_SC_OV; - } - /* - * !!! ignore all characters if CREAD is not set - */ - if ((cflag & CREAD) == 0) - info->read_status_mask &= ~BD_SC_EMPTY; - local_irq_save(flags); - - /* Start bit has not been added (so don't, because we would just - * subtract it later), and we need to add one for the number of - * stops bits (there is always at least one). - */ - bits++; - idx = PORT_NUM(state->smc_scc_num); - if (state->smc_scc_num & NUM_IS_SCC) { - sccp = &pquicc->scc_regs[idx]; - sccp->scc_psmr = (sbits << 12) | scval; - } else { - smcp = &pquicc->smc_regs[idx]; - - /* Set the mode register. We want to keep a copy of the - * enables, because we want to put them back if they were - * present. - */ - prev_mode = smcp->smc_smcmr; - smcp->smc_smcmr = smcr_mk_clen(bits) | cval | SMCMR_SM_UART; - smcp->smc_smcmr |= (prev_mode & (SMCMR_REN | SMCMR_TEN)); - } - - m360_cpm_setbrg((state - rs_table), baud_rate); - - local_irq_restore(flags); -} - -static void rs_360_put_char(struct tty_struct *tty, unsigned char ch) -{ - ser_info_t *info = (ser_info_t *)tty->driver_data; - volatile QUICC_BD *bdp; - - if (serial_paranoia_check(info, tty->name, "rs_put_char")) - return 0; - - if (!tty) - return 0; - - bdp = info->tx_cur; - while (bdp->status & BD_SC_READY); - - /* *((char *)__va(bdp->buf)) = ch; */ - *((char *)bdp->buf) = ch; - bdp->length = 1; - bdp->status |= BD_SC_READY; - - /* Get next BD. - */ - if (bdp->status & BD_SC_WRAP) - bdp = info->tx_bd_base; - else - bdp++; - - info->tx_cur = (QUICC_BD *)bdp; - return 1; - -} - -static int rs_360_write(struct tty_struct * tty, - const unsigned char *buf, int count) -{ - int c, ret = 0; - ser_info_t *info = (ser_info_t *)tty->driver_data; - volatile QUICC_BD *bdp; - -#ifdef CONFIG_KGDB - /* Try to let stub handle output. Returns true if it did. */ - if (kgdb_output_string(buf, count)) - return ret; -#endif - - if (serial_paranoia_check(info, tty->name, "rs_write")) - return 0; - - if (!tty) - return 0; - - bdp = info->tx_cur; - - while (1) { - c = min(count, TX_BUF_SIZE); - - if (c <= 0) - break; - - if (bdp->status & BD_SC_READY) { - info->flags |= TX_WAKEUP; - break; - } - - /* memcpy(__va(bdp->buf), buf, c); */ - memcpy((void *)bdp->buf, buf, c); - - bdp->length = c; - bdp->status |= BD_SC_READY; - - buf += c; - count -= c; - ret += c; - - /* Get next BD. - */ - if (bdp->status & BD_SC_WRAP) - bdp = info->tx_bd_base; - else - bdp++; - info->tx_cur = (QUICC_BD *)bdp; - } - return ret; -} - -static int rs_360_write_room(struct tty_struct *tty) -{ - ser_info_t *info = (ser_info_t *)tty->driver_data; - int ret; - - if (serial_paranoia_check(info, tty->name, "rs_write_room")) - return 0; - - if ((info->tx_cur->status & BD_SC_READY) == 0) { - info->flags &= ~TX_WAKEUP; - ret = TX_BUF_SIZE; - } - else { - info->flags |= TX_WAKEUP; - ret = 0; - } - return ret; -} - -/* I could track this with transmit counters....maybe later. -*/ -static int rs_360_chars_in_buffer(struct tty_struct *tty) -{ - ser_info_t *info = (ser_info_t *)tty->driver_data; - - if (serial_paranoia_check(info, tty->name, "rs_chars_in_buffer")) - return 0; - return 0; -} - -static void rs_360_flush_buffer(struct tty_struct *tty) -{ - ser_info_t *info = (ser_info_t *)tty->driver_data; - - if (serial_paranoia_check(info, tty->name, "rs_flush_buffer")) - return; - - /* There is nothing to "flush", whatever we gave the CPM - * is on its way out. - */ - tty_wakeup(tty); - info->flags &= ~TX_WAKEUP; -} - -/* - * This function is used to send a high-priority XON/XOFF character to - * the device - */ -static void rs_360_send_xchar(struct tty_struct *tty, char ch) -{ - volatile QUICC_BD *bdp; - - ser_info_t *info = (ser_info_t *)tty->driver_data; - - if (serial_paranoia_check(info, tty->name, "rs_send_char")) - return; - - bdp = info->tx_cur; - while (bdp->status & BD_SC_READY); - - /* *((char *)__va(bdp->buf)) = ch; */ - *((char *)bdp->buf) = ch; - bdp->length = 1; - bdp->status |= BD_SC_READY; - - /* Get next BD. - */ - if (bdp->status & BD_SC_WRAP) - bdp = info->tx_bd_base; - else - bdp++; - - info->tx_cur = (QUICC_BD *)bdp; -} - -/* - * ------------------------------------------------------------ - * rs_throttle() - * - * This routine is called by the upper-layer tty layer to signal that - * incoming characters should be throttled. - * ------------------------------------------------------------ - */ -static void rs_360_throttle(struct tty_struct * tty) -{ - ser_info_t *info = (ser_info_t *)tty->driver_data; -#ifdef SERIAL_DEBUG_THROTTLE - char buf[64]; - - printk("throttle %s: %d....\n", _tty_name(tty, buf), - tty->ldisc.chars_in_buffer(tty)); -#endif - - if (serial_paranoia_check(info, tty->name, "rs_throttle")) - return; - - if (I_IXOFF(tty)) - rs_360_send_xchar(tty, STOP_CHAR(tty)); - -#ifdef modem_control - if (tty->termios->c_cflag & CRTSCTS) - info->MCR &= ~UART_MCR_RTS; - - local_irq_disable(); - serial_out(info, UART_MCR, info->MCR); - local_irq_enable(); -#endif -} - -static void rs_360_unthrottle(struct tty_struct * tty) -{ - ser_info_t *info = (ser_info_t *)tty->driver_data; -#ifdef SERIAL_DEBUG_THROTTLE - char buf[64]; - - printk("unthrottle %s: %d....\n", _tty_name(tty, buf), - tty->ldisc.chars_in_buffer(tty)); -#endif - - if (serial_paranoia_check(info, tty->name, "rs_unthrottle")) - return; - - if (I_IXOFF(tty)) { - if (info->x_char) - info->x_char = 0; - else - rs_360_send_xchar(tty, START_CHAR(tty)); - } -#ifdef modem_control - if (tty->termios->c_cflag & CRTSCTS) - info->MCR |= UART_MCR_RTS; - local_irq_disable(); - serial_out(info, UART_MCR, info->MCR); - local_irq_enable(); -#endif -} - -/* - * ------------------------------------------------------------ - * rs_ioctl() and friends - * ------------------------------------------------------------ - */ - -#ifdef maybe -/* - * get_lsr_info - get line status register info - * - * Purpose: Let user call ioctl() to get info when the UART physically - * is emptied. On bus types like RS485, the transmitter must - * release the bus after transmitting. This must be done when - * the transmit shift register is empty, not be done when the - * transmit holding register is empty. This functionality - * allows an RS485 driver to be written in user space. - */ -static int get_lsr_info(struct async_struct * info, unsigned int *value) -{ - unsigned char status; - unsigned int result; - - local_irq_disable(); - status = serial_in(info, UART_LSR); - local_irq_enable(); - result = ((status & UART_LSR_TEMT) ? TIOCSER_TEMT : 0); - return put_user(result,value); -} -#endif - -static int rs_360_tiocmget(struct tty_struct *tty, struct file *file) -{ - ser_info_t *info = (ser_info_t *)tty->driver_data; - unsigned int result = 0; -#ifdef modem_control - unsigned char control, status; - - if (serial_paranoia_check(info, tty->name, __func__)) - return -ENODEV; - - if (tty->flags & (1 << TTY_IO_ERROR)) - return -EIO; - - control = info->MCR; - local_irq_disable(); - status = serial_in(info, UART_MSR); - local_irq_enable(); - result = ((control & UART_MCR_RTS) ? TIOCM_RTS : 0) - | ((control & UART_MCR_DTR) ? TIOCM_DTR : 0) -#ifdef TIOCM_OUT1 - | ((control & UART_MCR_OUT1) ? TIOCM_OUT1 : 0) - | ((control & UART_MCR_OUT2) ? TIOCM_OUT2 : 0) -#endif - | ((status & UART_MSR_DCD) ? TIOCM_CAR : 0) - | ((status & UART_MSR_RI) ? TIOCM_RNG : 0) - | ((status & UART_MSR_DSR) ? TIOCM_DSR : 0) - | ((status & UART_MSR_CTS) ? TIOCM_CTS : 0); -#endif - return result; -} - -static int rs_360_tiocmset(struct tty_struct *tty, struct file *file, - unsigned int set, unsigned int clear) -{ -#ifdef modem_control - ser_info_t *info = (ser_info_t *)tty->driver_data; - unsigned int arg; - - if (serial_paranoia_check(info, tty->name, __func__)) - return -ENODEV; - - if (tty->flags & (1 << TTY_IO_ERROR)) - return -EIO; - /* FIXME: locking on info->mcr */ - if (set & TIOCM_RTS) - info->mcr |= UART_MCR_RTS; - if (set & TIOCM_DTR) - info->mcr |= UART_MCR_DTR; - if (clear & TIOCM_RTS) - info->MCR &= ~UART_MCR_RTS; - if (clear & TIOCM_DTR) - info->MCR &= ~UART_MCR_DTR; - -#ifdef TIOCM_OUT1 - if (set & TIOCM_OUT1) - info->MCR |= UART_MCR_OUT1; - if (set & TIOCM_OUT2) - info->MCR |= UART_MCR_OUT2; - if (clear & TIOCM_OUT1) - info->MCR &= ~UART_MCR_OUT1; - if (clear & TIOCM_OUT2) - info->MCR &= ~UART_MCR_OUT2; -#endif - - local_irq_disable(); - serial_out(info, UART_MCR, info->MCR); - local_irq_enable(); -#endif - return 0; -} - -/* Sending a break is a two step process on the SMC/SCC. It is accomplished - * by sending a STOP TRANSMIT command followed by a RESTART TRANSMIT - * command. We take advantage of the begin/end functions to make this - * happen. - */ -static ushort smc_chan_map[] = { - CPM_CR_CH_SMC1, - CPM_CR_CH_SMC2 -}; - -static ushort scc_chan_map[] = { - CPM_CR_CH_SCC1, - CPM_CR_CH_SCC2, - CPM_CR_CH_SCC3, - CPM_CR_CH_SCC4 -}; - -static void begin_break(ser_info_t *info) -{ - volatile QUICC *cp; - ushort chan; - int idx; - - cp = pquicc; - - idx = PORT_NUM(info->state->smc_scc_num); - if (info->state->smc_scc_num & NUM_IS_SCC) - chan = scc_chan_map[idx]; - else - chan = smc_chan_map[idx]; - - cp->cp_cr = mk_cr_cmd(chan, CPM_CR_STOP_TX) | CPM_CR_FLG; - while (cp->cp_cr & CPM_CR_FLG); -} - -static void end_break(ser_info_t *info) -{ - volatile QUICC *cp; - ushort chan; - int idx; - - cp = pquicc; - - idx = PORT_NUM(info->state->smc_scc_num); - if (info->state->smc_scc_num & NUM_IS_SCC) - chan = scc_chan_map[idx]; - else - chan = smc_chan_map[idx]; - - cp->cp_cr = mk_cr_cmd(chan, CPM_CR_RESTART_TX) | CPM_CR_FLG; - while (cp->cp_cr & CPM_CR_FLG); -} - -/* - * This routine sends a break character out the serial port. - */ -static void send_break(ser_info_t *info, unsigned int duration) -{ -#ifdef SERIAL_DEBUG_SEND_BREAK - printk("rs_send_break(%d) jiff=%lu...", duration, jiffies); -#endif - begin_break(info); - msleep_interruptible(duration); - end_break(info); -#ifdef SERIAL_DEBUG_SEND_BREAK - printk("done jiffies=%lu\n", jiffies); -#endif -} - - -/* - * Get counter of input serial line interrupts (DCD,RI,DSR,CTS) - * Return: write counters to the user passed counter struct - * NB: both 1->0 and 0->1 transitions are counted except for - * RI where only 0->1 is counted. - */ -static int rs_360_get_icount(struct tty_struct *tty, - struct serial_icounter_struct *icount) -{ - ser_info_t *info = (ser_info_t *)tty->driver_data; - struct async_icount cnow; - - local_irq_disable(); - cnow = info->state->icount; - local_irq_enable(); - - icount->cts = cnow.cts; - icount->dsr = cnow.dsr; - icount->rng = cnow.rng; - icount->dcd = cnow.dcd; - - return 0; -} - -static int rs_360_ioctl(struct tty_struct *tty, struct file * file, - unsigned int cmd, unsigned long arg) -{ - int error; - ser_info_t *info = (ser_info_t *)tty->driver_data; - int retval; - struct async_icount cnow; - /* struct async_icount_24 cnow;*/ /* kernel counter temps */ - struct serial_icounter_struct *p_cuser; /* user space */ - - if (serial_paranoia_check(info, tty->name, "rs_ioctl")) - return -ENODEV; - - if (cmd != TIOCMIWAIT) { - if (tty->flags & (1 << TTY_IO_ERROR)) - return -EIO; - } - - switch (cmd) { - case TCSBRK: /* SVID version: non-zero arg --> no break */ - retval = tty_check_change(tty); - if (retval) - return retval; - tty_wait_until_sent(tty, 0); - if (signal_pending(current)) - return -EINTR; - if (!arg) { - send_break(info, 250); /* 1/4 second */ - if (signal_pending(current)) - return -EINTR; - } - return 0; - case TCSBRKP: /* support for POSIX tcsendbreak() */ - retval = tty_check_change(tty); - if (retval) - return retval; - tty_wait_until_sent(tty, 0); - if (signal_pending(current)) - return -EINTR; - send_break(info, arg ? arg*100 : 250); - if (signal_pending(current)) - return -EINTR; - return 0; - case TIOCSBRK: - retval = tty_check_change(tty); - if (retval) - return retval; - tty_wait_until_sent(tty, 0); - begin_break(info); - return 0; - case TIOCCBRK: - retval = tty_check_change(tty); - if (retval) - return retval; - end_break(info); - return 0; -#ifdef maybe - case TIOCSERGETLSR: /* Get line status register */ - return get_lsr_info(info, (unsigned int *) arg); -#endif - /* - * Wait for any of the 4 modem inputs (DCD,RI,DSR,CTS) to change - * - mask passed in arg for lines of interest - * (use |'ed TIOCM_RNG/DSR/CD/CTS for masking) - * Caller should use TIOCGICOUNT to see which one it was - */ - case TIOCMIWAIT: -#ifdef modem_control - local_irq_disable(); - /* note the counters on entry */ - cprev = info->state->icount; - local_irq_enable(); - while (1) { - interruptible_sleep_on(&info->delta_msr_wait); - /* see if a signal did it */ - if (signal_pending(current)) - return -ERESTARTSYS; - local_irq_disable(); - cnow = info->state->icount; /* atomic copy */ - local_irq_enable(); - if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr && - cnow.dcd == cprev.dcd && cnow.cts == cprev.cts) - return -EIO; /* no change => error */ - if ( ((arg & TIOCM_RNG) && (cnow.rng != cprev.rng)) || - ((arg & TIOCM_DSR) && (cnow.dsr != cprev.dsr)) || - ((arg & TIOCM_CD) && (cnow.dcd != cprev.dcd)) || - ((arg & TIOCM_CTS) && (cnow.cts != cprev.cts)) ) { - return 0; - } - cprev = cnow; - } - /* NOTREACHED */ -#else - return 0; -#endif - - - default: - return -ENOIOCTLCMD; - } - return 0; -} - -/* FIX UP modem control here someday...... -*/ -static void rs_360_set_termios(struct tty_struct *tty, struct ktermios *old_termios) -{ - ser_info_t *info = (ser_info_t *)tty->driver_data; - - change_speed(info); - -#ifdef modem_control - /* Handle transition to B0 status */ - if ((old_termios->c_cflag & CBAUD) && - !(tty->termios->c_cflag & CBAUD)) { - info->MCR &= ~(UART_MCR_DTR|UART_MCR_RTS); - local_irq_disable(); - serial_out(info, UART_MCR, info->MCR); - local_irq_enable(); - } - - /* Handle transition away from B0 status */ - if (!(old_termios->c_cflag & CBAUD) && - (tty->termios->c_cflag & CBAUD)) { - info->MCR |= UART_MCR_DTR; - if (!tty->hw_stopped || - !(tty->termios->c_cflag & CRTSCTS)) { - info->MCR |= UART_MCR_RTS; - } - local_irq_disable(); - serial_out(info, UART_MCR, info->MCR); - local_irq_enable(); - } - - /* Handle turning off CRTSCTS */ - if ((old_termios->c_cflag & CRTSCTS) && - !(tty->termios->c_cflag & CRTSCTS)) { - tty->hw_stopped = 0; - rs_360_start(tty); - } -#endif - -#if 0 - /* - * No need to wake up processes in open wait, since they - * sample the CLOCAL flag once, and don't recheck it. - * XXX It's not clear whether the current behavior is correct - * or not. Hence, this may change..... - */ - if (!(old_termios->c_cflag & CLOCAL) && - (tty->termios->c_cflag & CLOCAL)) - wake_up_interruptible(&info->open_wait); -#endif -} - -/* - * ------------------------------------------------------------ - * rs_close() - * - * This routine is called when the serial port gets closed. First, we - * wait for the last remaining data to be sent. Then, we unlink its - * async structure from the interrupt chain if necessary, and we free - * that IRQ if nothing is left in the chain. - * ------------------------------------------------------------ - */ -static void rs_360_close(struct tty_struct *tty, struct file * filp) -{ - ser_info_t *info = (ser_info_t *)tty->driver_data; - /* struct async_state *state; */ - struct serial_state *state; - unsigned long flags; - int idx; - volatile struct smc_regs *smcp; - volatile struct scc_regs *sccp; - - if (!info || serial_paranoia_check(info, tty->name, "rs_close")) - return; - - state = info->state; - - local_irq_save(flags); - - if (tty_hung_up_p(filp)) { - DBG_CNT("before DEC-hung"); - local_irq_restore(flags); - return; - } - -#ifdef SERIAL_DEBUG_OPEN - printk("rs_close ttys%d, count = %d\n", info->line, state->count); -#endif - if ((tty->count == 1) && (state->count != 1)) { - /* - * Uh, oh. tty->count is 1, which means that the tty - * structure will be freed. state->count should always - * be one in these conditions. If it's greater than - * one, we've got real problems, since it means the - * serial port won't be shutdown. - */ - printk("rs_close: bad serial port count; tty->count is 1, " - "state->count is %d\n", state->count); - state->count = 1; - } - if (--state->count < 0) { - printk("rs_close: bad serial port count for ttys%d: %d\n", - info->line, state->count); - state->count = 0; - } - if (state->count) { - DBG_CNT("before DEC-2"); - local_irq_restore(flags); - return; - } - info->flags |= ASYNC_CLOSING; - /* - * Now we wait for the transmit buffer to clear; and we notify - * the line discipline to only process XON/XOFF characters. - */ - tty->closing = 1; - if (info->closing_wait != ASYNC_CLOSING_WAIT_NONE) - tty_wait_until_sent(tty, info->closing_wait); - /* - * At this point we stop accepting input. To do this, we - * disable the receive line status interrupts, and tell the - * interrupt driver to stop checking the data ready bit in the - * line status register. - */ - info->read_status_mask &= ~BD_SC_EMPTY; - if (info->flags & ASYNC_INITIALIZED) { - - idx = PORT_NUM(info->state->smc_scc_num); - if (info->state->smc_scc_num & NUM_IS_SCC) { - sccp = &pquicc->scc_regs[idx]; - sccp->scc_sccm &= ~UART_SCCM_RX; - sccp->scc_gsmr.w.low &= ~SCC_GSMRL_ENR; - } else { - smcp = &pquicc->smc_regs[idx]; - smcp->smc_smcm &= ~SMCM_RX; - smcp->smc_smcmr &= ~SMCMR_REN; - } - /* - * Before we drop DTR, make sure the UART transmitter - * has completely drained; this is especially - * important if there is a transmit FIFO! - */ - rs_360_wait_until_sent(tty, info->timeout); - } - shutdown(info); - rs_360_flush_buffer(tty); - tty_ldisc_flush(tty); - tty->closing = 0; - info->event = 0; - info->port.tty = NULL; - if (info->blocked_open) { - if (info->close_delay) { - msleep_interruptible(jiffies_to_msecs(info->close_delay)); - } - wake_up_interruptible(&info->open_wait); - } - info->flags &= ~(ASYNC_NORMAL_ACTIVE|ASYNC_CLOSING); - wake_up_interruptible(&info->close_wait); - local_irq_restore(flags); -} - -/* - * rs_wait_until_sent() --- wait until the transmitter is empty - */ -static void rs_360_wait_until_sent(struct tty_struct *tty, int timeout) -{ - ser_info_t *info = (ser_info_t *)tty->driver_data; - unsigned long orig_jiffies, char_time; - /*int lsr;*/ - volatile QUICC_BD *bdp; - - if (serial_paranoia_check(info, tty->name, "rs_wait_until_sent")) - return; - -#ifdef maybe - if (info->state->type == PORT_UNKNOWN) - return; -#endif - - orig_jiffies = jiffies; - /* - * Set the check interval to be 1/5 of the estimated time to - * send a single character, and make it at least 1. The check - * interval should also be less than the timeout. - * - * Note: we have to use pretty tight timings here to satisfy - * the NIST-PCTS. - */ - char_time = 1; - if (timeout) - char_time = min(char_time, (unsigned long)timeout); -#ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT - printk("In rs_wait_until_sent(%d) check=%lu...", timeout, char_time); - printk("jiff=%lu...", jiffies); -#endif - - /* We go through the loop at least once because we can't tell - * exactly when the last character exits the shifter. There can - * be at least two characters waiting to be sent after the buffers - * are empty. - */ - do { -#ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT - printk("lsr = %d (jiff=%lu)...", lsr, jiffies); -#endif -/* current->counter = 0; make us low-priority */ - msleep_interruptible(jiffies_to_msecs(char_time)); - if (signal_pending(current)) - break; - if (timeout && (time_after(jiffies, orig_jiffies + timeout))) - break; - /* The 'tx_cur' is really the next buffer to send. We - * have to back up to the previous BD and wait for it - * to go. This isn't perfect, because all this indicates - * is the buffer is available. There are still characters - * in the CPM FIFO. - */ - bdp = info->tx_cur; - if (bdp == info->tx_bd_base) - bdp += (TX_NUM_FIFO-1); - else - bdp--; - } while (bdp->status & BD_SC_READY); - current->state = TASK_RUNNING; -#ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT - printk("lsr = %d (jiff=%lu)...done\n", lsr, jiffies); -#endif -} - -/* - * rs_hangup() --- called by tty_hangup() when a hangup is signaled. - */ -static void rs_360_hangup(struct tty_struct *tty) -{ - ser_info_t *info = (ser_info_t *)tty->driver_data; - struct serial_state *state = info->state; - - if (serial_paranoia_check(info, tty->name, "rs_hangup")) - return; - - state = info->state; - - rs_360_flush_buffer(tty); - shutdown(info); - info->event = 0; - state->count = 0; - info->flags &= ~ASYNC_NORMAL_ACTIVE; - info->port.tty = NULL; - wake_up_interruptible(&info->open_wait); -} - -/* - * ------------------------------------------------------------ - * rs_open() and friends - * ------------------------------------------------------------ - */ -static int block_til_ready(struct tty_struct *tty, struct file * filp, - ser_info_t *info) -{ -#ifdef DO_THIS_LATER - DECLARE_WAITQUEUE(wait, current); -#endif - struct serial_state *state = info->state; - int retval; - int do_clocal = 0; - - /* - * If the device is in the middle of being closed, then block - * until it's done, and then try again. - */ - if (tty_hung_up_p(filp) || - (info->flags & ASYNC_CLOSING)) { - if (info->flags & ASYNC_CLOSING) - interruptible_sleep_on(&info->close_wait); -#ifdef SERIAL_DO_RESTART - if (info->flags & ASYNC_HUP_NOTIFY) - return -EAGAIN; - else - return -ERESTARTSYS; -#else - return -EAGAIN; -#endif - } - - /* - * If non-blocking mode is set, or the port is not enabled, - * then make the check up front and then exit. - * If this is an SMC port, we don't have modem control to wait - * for, so just get out here. - */ - if ((filp->f_flags & O_NONBLOCK) || - (tty->flags & (1 << TTY_IO_ERROR)) || - !(info->state->smc_scc_num & NUM_IS_SCC)) { - info->flags |= ASYNC_NORMAL_ACTIVE; - return 0; - } - - if (tty->termios->c_cflag & CLOCAL) - do_clocal = 1; - - /* - * Block waiting for the carrier detect and the line to become - * free (i.e., not in use by the callout). While we are in - * this loop, state->count is dropped by one, so that - * rs_close() knows when to free things. We restore it upon - * exit, either normal or abnormal. - */ - retval = 0; -#ifdef DO_THIS_LATER - add_wait_queue(&info->open_wait, &wait); -#ifdef SERIAL_DEBUG_OPEN - printk("block_til_ready before block: ttys%d, count = %d\n", - state->line, state->count); -#endif - local_irq_disable(); - if (!tty_hung_up_p(filp)) - state->count--; - local_irq_enable(); - info->blocked_open++; - while (1) { - local_irq_disable(); - if (tty->termios->c_cflag & CBAUD) - serial_out(info, UART_MCR, - serial_inp(info, UART_MCR) | - (UART_MCR_DTR | UART_MCR_RTS)); - local_irq_enable(); - set_current_state(TASK_INTERRUPTIBLE); - if (tty_hung_up_p(filp) || - !(info->flags & ASYNC_INITIALIZED)) { -#ifdef SERIAL_DO_RESTART - if (info->flags & ASYNC_HUP_NOTIFY) - retval = -EAGAIN; - else - retval = -ERESTARTSYS; -#else - retval = -EAGAIN; -#endif - break; - } - if (!(info->flags & ASYNC_CLOSING) && - (do_clocal || (serial_in(info, UART_MSR) & - UART_MSR_DCD))) - break; - if (signal_pending(current)) { - retval = -ERESTARTSYS; - break; - } -#ifdef SERIAL_DEBUG_OPEN - printk("block_til_ready blocking: ttys%d, count = %d\n", - info->line, state->count); -#endif - tty_unlock(); - schedule(); - tty_lock(); - } - current->state = TASK_RUNNING; - remove_wait_queue(&info->open_wait, &wait); - if (!tty_hung_up_p(filp)) - state->count++; - info->blocked_open--; -#ifdef SERIAL_DEBUG_OPEN - printk("block_til_ready after blocking: ttys%d, count = %d\n", - info->line, state->count); -#endif -#endif /* DO_THIS_LATER */ - if (retval) - return retval; - info->flags |= ASYNC_NORMAL_ACTIVE; - return 0; -} - -static int get_async_struct(int line, ser_info_t **ret_info) -{ - struct serial_state *sstate; - - sstate = rs_table + line; - if (sstate->info) { - sstate->count++; - *ret_info = (ser_info_t *)sstate->info; - return 0; - } - else { - return -ENOMEM; - } -} - -/* - * This routine is called whenever a serial port is opened. It - * enables interrupts for a serial port, linking in its async structure into - * the IRQ chain. It also performs the serial-specific - * initialization for the tty structure. - */ -static int rs_360_open(struct tty_struct *tty, struct file * filp) -{ - ser_info_t *info; - int retval, line; - - line = tty->index; - if ((line < 0) || (line >= NR_PORTS)) - return -ENODEV; - retval = get_async_struct(line, &info); - if (retval) - return retval; - if (serial_paranoia_check(info, tty->name, "rs_open")) - return -ENODEV; - -#ifdef SERIAL_DEBUG_OPEN - printk("rs_open %s, count = %d\n", tty->name, info->state->count); -#endif - tty->driver_data = info; - info->port.tty = tty; - - /* - * Start up serial port - */ - retval = startup(info); - if (retval) - return retval; - - retval = block_til_ready(tty, filp, info); - if (retval) { -#ifdef SERIAL_DEBUG_OPEN - printk("rs_open returning after block_til_ready with %d\n", - retval); -#endif - return retval; - } - -#ifdef SERIAL_DEBUG_OPEN - printk("rs_open %s successful...", tty->name); -#endif - return 0; -} - -/* - * /proc fs routines.... - */ - -static inline int line_info(char *buf, struct serial_state *state) -{ -#ifdef notdef - struct async_struct *info = state->info, scr_info; - char stat_buf[30], control, status; -#endif - int ret; - - ret = sprintf(buf, "%d: uart:%s port:%X irq:%d", - state->line, - (state->smc_scc_num & NUM_IS_SCC) ? "SCC" : "SMC", - (unsigned int)(state->port), state->irq); - - if (!state->port || (state->type == PORT_UNKNOWN)) { - ret += sprintf(buf+ret, "\n"); - return ret; - } - -#ifdef notdef - /* - * Figure out the current RS-232 lines - */ - if (!info) { - info = &scr_info; /* This is just for serial_{in,out} */ - - info->magic = SERIAL_MAGIC; - info->port = state->port; - info->flags = state->flags; - info->quot = 0; - info->port.tty = NULL; - } - local_irq_disable(); - status = serial_in(info, UART_MSR); - control = info ? info->MCR : serial_in(info, UART_MCR); - local_irq_enable(); - - stat_buf[0] = 0; - stat_buf[1] = 0; - if (control & UART_MCR_RTS) - strcat(stat_buf, "|RTS"); - if (status & UART_MSR_CTS) - strcat(stat_buf, "|CTS"); - if (control & UART_MCR_DTR) - strcat(stat_buf, "|DTR"); - if (status & UART_MSR_DSR) - strcat(stat_buf, "|DSR"); - if (status & UART_MSR_DCD) - strcat(stat_buf, "|CD"); - if (status & UART_MSR_RI) - strcat(stat_buf, "|RI"); - - if (info->quot) { - ret += sprintf(buf+ret, " baud:%d", - state->baud_base / info->quot); - } - - ret += sprintf(buf+ret, " tx:%d rx:%d", - state->icount.tx, state->icount.rx); - - if (state->icount.frame) - ret += sprintf(buf+ret, " fe:%d", state->icount.frame); - - if (state->icount.parity) - ret += sprintf(buf+ret, " pe:%d", state->icount.parity); - - if (state->icount.brk) - ret += sprintf(buf+ret, " brk:%d", state->icount.brk); - - if (state->icount.overrun) - ret += sprintf(buf+ret, " oe:%d", state->icount.overrun); - - /* - * Last thing is the RS-232 status lines - */ - ret += sprintf(buf+ret, " %s\n", stat_buf+1); -#endif - return ret; -} - -int rs_360_read_proc(char *page, char **start, off_t off, int count, - int *eof, void *data) -{ - int i, len = 0; - off_t begin = 0; - - len += sprintf(page, "serinfo:1.0 driver:%s\n", serial_version); - for (i = 0; i < NR_PORTS && len < 4000; i++) { - len += line_info(page + len, &rs_table[i]); - if (len+begin > off+count) - goto done; - if (len+begin < off) { - begin += len; - len = 0; - } - } - *eof = 1; -done: - if (off >= len+begin) - return 0; - *start = page + (begin-off); - return ((count < begin+len-off) ? count : begin+len-off); -} - -/* - * --------------------------------------------------------------------- - * rs_init() and friends - * - * rs_init() is called at boot-time to initialize the serial driver. - * --------------------------------------------------------------------- - */ - -/* - * This routine prints out the appropriate serial driver version - * number, and identifies which options were configured into this - * driver. - */ -static _INLINE_ void show_serial_version(void) -{ - printk(KERN_INFO "%s version %s\n", serial_name, serial_version); -} - - -/* - * The serial console driver used during boot. Note that these names - * clash with those found in "serial.c", so we currently can't support - * the 16xxx uarts and these at the same time. I will fix this to become - * an indirect function call from tty_io.c (or something). - */ - -#ifdef CONFIG_SERIAL_CONSOLE - -/* - * Print a string to the serial port trying not to disturb any possible - * real use of the port... - */ -static void my_console_write(int idx, const char *s, - unsigned count) -{ - struct serial_state *ser; - ser_info_t *info; - unsigned i; - QUICC_BD *bdp, *bdbase; - volatile struct smc_uart_pram *up; - volatile u_char *cp; - - ser = rs_table + idx; - - - /* If the port has been initialized for general use, we have - * to use the buffer descriptors allocated there. Otherwise, - * we simply use the single buffer allocated. - */ - if ((info = (ser_info_t *)ser->info) != NULL) { - bdp = info->tx_cur; - bdbase = info->tx_bd_base; - } - else { - /* Pointer to UART in parameter ram. - */ - /* up = (smc_uart_t *)&cpmp->cp_dparam[ser->port]; */ - up = &pquicc->pram[ser->port].scc.pothers.idma_smc.psmc.u; - - /* Get the address of the host memory buffer. - */ - bdp = bdbase = (QUICC_BD *)((uint)pquicc + (uint)up->tbase); - } - - /* - * We need to gracefully shut down the transmitter, disable - * interrupts, then send our bytes out. - */ - - /* - * Now, do each character. This is not as bad as it looks - * since this is a holding FIFO and not a transmitting FIFO. - * We could add the complexity of filling the entire transmit - * buffer, but we would just wait longer between accesses...... - */ - for (i = 0; i < count; i++, s++) { - /* Wait for transmitter fifo to empty. - * Ready indicates output is ready, and xmt is doing - * that, not that it is ready for us to send. - */ - while (bdp->status & BD_SC_READY); - - /* Send the character out. - */ - cp = bdp->buf; - *cp = *s; - - bdp->length = 1; - bdp->status |= BD_SC_READY; - - if (bdp->status & BD_SC_WRAP) - bdp = bdbase; - else - bdp++; - - /* if a LF, also do CR... */ - if (*s == 10) { - while (bdp->status & BD_SC_READY); - /* cp = __va(bdp->buf); */ - cp = bdp->buf; - *cp = 13; - bdp->length = 1; - bdp->status |= BD_SC_READY; - - if (bdp->status & BD_SC_WRAP) { - bdp = bdbase; - } - else { - bdp++; - } - } - } - - /* - * Finally, Wait for transmitter & holding register to empty - * and restore the IER - */ - while (bdp->status & BD_SC_READY); - - if (info) - info->tx_cur = (QUICC_BD *)bdp; -} - -static void serial_console_write(struct console *c, const char *s, - unsigned count) -{ -#ifdef CONFIG_KGDB - /* Try to let stub handle output. Returns true if it did. */ - if (kgdb_output_string(s, count)) - return; -#endif - my_console_write(c->index, s, count); -} - - - -/*void console_print_68360(const char *p) -{ - const char *cp = p; - int i; - - for (i=0;cp[i]!=0;i++); - - serial_console_write (p, i); - - //Comment this if you want to have a strict interrupt-driven output - //rs_fair_output(); - - return; -}*/ - - - - - - -#ifdef CONFIG_XMON -int -xmon_360_write(const char *s, unsigned count) -{ - my_console_write(0, s, count); - return(count); -} -#endif - -#ifdef CONFIG_KGDB -void -putDebugChar(char ch) -{ - my_console_write(0, &ch, 1); -} -#endif - -/* - * Receive character from the serial port. This only works well - * before the port is initialized for real use. - */ -static int my_console_wait_key(int idx, int xmon, char *obuf) -{ - struct serial_state *ser; - u_char c, *cp; - ser_info_t *info; - QUICC_BD *bdp; - volatile struct smc_uart_pram *up; - int i; - - ser = rs_table + idx; - - /* Get the address of the host memory buffer. - * If the port has been initialized for general use, we must - * use information from the port structure. - */ - if ((info = (ser_info_t *)ser->info)) - bdp = info->rx_cur; - else - /* bdp = (QUICC_BD *)&cpmp->cp_dpmem[up->smc_rbase]; */ - bdp = (QUICC_BD *)((uint)pquicc + (uint)up->tbase); - - /* Pointer to UART in parameter ram. - */ - /* up = (smc_uart_t *)&cpmp->cp_dparam[ser->port]; */ - up = &pquicc->pram[info->state->port].scc.pothers.idma_smc.psmc.u; - - /* - * We need to gracefully shut down the receiver, disable - * interrupts, then read the input. - * XMON just wants a poll. If no character, return -1, else - * return the character. - */ - if (!xmon) { - while (bdp->status & BD_SC_EMPTY); - } - else { - if (bdp->status & BD_SC_EMPTY) - return -1; - } - - cp = (char *)bdp->buf; - - if (obuf) { - i = c = bdp->length; - while (i-- > 0) - *obuf++ = *cp++; - } - else { - c = *cp; - } - bdp->status |= BD_SC_EMPTY; - - if (info) { - if (bdp->status & BD_SC_WRAP) { - bdp = info->rx_bd_base; - } - else { - bdp++; - } - info->rx_cur = (QUICC_BD *)bdp; - } - - return((int)c); -} - -static int serial_console_wait_key(struct console *co) -{ - return(my_console_wait_key(co->index, 0, NULL)); -} - -#ifdef CONFIG_XMON -int -xmon_360_read_poll(void) -{ - return(my_console_wait_key(0, 1, NULL)); -} - -int -xmon_360_read_char(void) -{ - return(my_console_wait_key(0, 0, NULL)); -} -#endif - -#ifdef CONFIG_KGDB -static char kgdb_buf[RX_BUF_SIZE], *kgdp; -static int kgdb_chars; - -unsigned char -getDebugChar(void) -{ - if (kgdb_chars <= 0) { - kgdb_chars = my_console_wait_key(0, 0, kgdb_buf); - kgdp = kgdb_buf; - } - kgdb_chars--; - - return(*kgdp++); -} - -void kgdb_interruptible(int state) -{ -} -void kgdb_map_scc(void) -{ - struct serial_state *ser; - uint mem_addr; - volatile QUICC_BD *bdp; - volatile smc_uart_t *up; - - cpmp = (cpm360_t *)&(((immap_t *)IMAP_ADDR)->im_cpm); - - /* To avoid data cache CPM DMA coherency problems, allocate a - * buffer in the CPM DPRAM. This will work until the CPM and - * serial ports are initialized. At that time a memory buffer - * will be allocated. - * The port is already initialized from the boot procedure, all - * we do here is give it a different buffer and make it a FIFO. - */ - - ser = rs_table; - - /* Right now, assume we are using SMCs. - */ - up = (smc_uart_t *)&cpmp->cp_dparam[ser->port]; - - /* Allocate space for an input FIFO, plus a few bytes for output. - * Allocate bytes to maintain word alignment. - */ - mem_addr = (uint)(&cpmp->cp_dpmem[0x1000]); - - /* Set the physical address of the host memory buffers in - * the buffer descriptors. - */ - bdp = (QUICC_BD *)&cpmp->cp_dpmem[up->smc_rbase]; - bdp->buf = mem_addr; - - bdp = (QUICC_BD *)&cpmp->cp_dpmem[up->smc_tbase]; - bdp->buf = mem_addr+RX_BUF_SIZE; - - up->smc_mrblr = RX_BUF_SIZE; /* receive buffer length */ - up->smc_maxidl = RX_BUF_SIZE; -} -#endif - -static struct tty_struct *serial_console_device(struct console *c, int *index) -{ - *index = c->index; - return serial_driver; -} - - -struct console sercons = { - .name = "ttyS", - .write = serial_console_write, - .device = serial_console_device, - .wait_key = serial_console_wait_key, - .setup = serial_console_setup, - .flags = CON_PRINTBUFFER, - .index = CONFIG_SERIAL_CONSOLE_PORT, -}; - - - -/* - * Register console. - */ -long console_360_init(long kmem_start, long kmem_end) -{ - register_console(&sercons); - /*register_console (console_print_68360); - 2.0.38 only required a write - function pointer. */ - return kmem_start; -} - -#endif - -/* Index in baud rate table of the default console baud rate. -*/ -static int baud_idx; - -static const struct tty_operations rs_360_ops = { - .owner = THIS_MODULE, - .open = rs_360_open, - .close = rs_360_close, - .write = rs_360_write, - .put_char = rs_360_put_char, - .write_room = rs_360_write_room, - .chars_in_buffer = rs_360_chars_in_buffer, - .flush_buffer = rs_360_flush_buffer, - .ioctl = rs_360_ioctl, - .throttle = rs_360_throttle, - .unthrottle = rs_360_unthrottle, - /* .send_xchar = rs_360_send_xchar, */ - .set_termios = rs_360_set_termios, - .stop = rs_360_stop, - .start = rs_360_start, - .hangup = rs_360_hangup, - /* .wait_until_sent = rs_360_wait_until_sent, */ - /* .read_proc = rs_360_read_proc, */ - .tiocmget = rs_360_tiocmget, - .tiocmset = rs_360_tiocmset, -}; - -static int __init rs_360_init(void) -{ - struct serial_state * state; - ser_info_t *info; - void *mem_addr; - uint dp_addr, iobits; - int i, j, idx; - ushort chan; - QUICC_BD *bdp; - volatile QUICC *cp; - volatile struct smc_regs *sp; - volatile struct smc_uart_pram *up; - volatile struct scc_regs *scp; - volatile struct uart_pram *sup; - /* volatile immap_t *immap; */ - - serial_driver = alloc_tty_driver(NR_PORTS); - if (!serial_driver) - return -1; - - show_serial_version(); - - serial_driver->name = "ttyS"; - serial_driver->major = TTY_MAJOR; - serial_driver->minor_start = 64; - serial_driver->type = TTY_DRIVER_TYPE_SERIAL; - serial_driver->subtype = SERIAL_TYPE_NORMAL; - serial_driver->init_termios = tty_std_termios; - serial_driver->init_termios.c_cflag = - baud_idx | CS8 | CREAD | HUPCL | CLOCAL; - serial_driver->flags = TTY_DRIVER_REAL_RAW; - tty_set_operations(serial_driver, &rs_360_ops); - - if (tty_register_driver(serial_driver)) - panic("Couldn't register serial driver\n"); - - cp = pquicc; /* Get pointer to Communication Processor */ - /* immap = (immap_t *)IMAP_ADDR; */ /* and to internal registers */ - - - /* Configure SCC2, SCC3, and SCC4 instead of port A parallel I/O. - */ - /* The "standard" configuration through the 860. - */ -/* immap->im_ioport.iop_papar |= 0x00fc; */ -/* immap->im_ioport.iop_padir &= ~0x00fc; */ -/* immap->im_ioport.iop_paodr &= ~0x00fc; */ - cp->pio_papar |= 0x00fc; - cp->pio_padir &= ~0x00fc; - /* cp->pio_paodr &= ~0x00fc; */ - - - /* Since we don't yet do modem control, connect the port C pins - * as general purpose I/O. This will assert CTS and CD for the - * SCC ports. - */ - /* FIXME: see 360um p.7-365 and 860um p.34-12 - * I can't make sense of these bits - mleslie*/ -/* immap->im_ioport.iop_pcdir |= 0x03c6; */ -/* immap->im_ioport.iop_pcpar &= ~0x03c6; */ - -/* cp->pio_pcdir |= 0x03c6; */ -/* cp->pio_pcpar &= ~0x03c6; */ - - - - /* Connect SCC2 and SCC3 to NMSI. Connect BRG3 to SCC2 and - * BRG4 to SCC3. - */ - cp->si_sicr &= ~0x00ffff00; - cp->si_sicr |= 0x001b1200; - -#ifdef CONFIG_PP04 - /* Frequentis PP04 forced to RS-232 until we know better. - * Port C 12 and 13 low enables RS-232 on SCC3 and SCC4. - */ - immap->im_ioport.iop_pcdir |= 0x000c; - immap->im_ioport.iop_pcpar &= ~0x000c; - immap->im_ioport.iop_pcdat &= ~0x000c; - - /* This enables the TX driver. - */ - cp->cp_pbpar &= ~0x6000; - cp->cp_pbdat &= ~0x6000; -#endif - - for (i = 0, state = rs_table; i < NR_PORTS; i++,state++) { - state->magic = SSTATE_MAGIC; - state->line = i; - state->type = PORT_UNKNOWN; - state->custom_divisor = 0; - state->close_delay = 5*HZ/10; - state->closing_wait = 30*HZ; - state->icount.cts = state->icount.dsr = - state->icount.rng = state->icount.dcd = 0; - state->icount.rx = state->icount.tx = 0; - state->icount.frame = state->icount.parity = 0; - state->icount.overrun = state->icount.brk = 0; - printk(KERN_INFO "ttyS%d at irq 0x%02x is an %s\n", - i, (unsigned int)(state->irq), - (state->smc_scc_num & NUM_IS_SCC) ? "SCC" : "SMC"); - -#ifdef CONFIG_SERIAL_CONSOLE - /* If we just printed the message on the console port, and - * we are about to initialize it for general use, we have - * to wait a couple of character times for the CR/NL to - * make it out of the transmit buffer. - */ - if (i == CONFIG_SERIAL_CONSOLE_PORT) - mdelay(8); - - -/* idx = PORT_NUM(info->state->smc_scc_num); */ -/* if (info->state->smc_scc_num & NUM_IS_SCC) */ -/* chan = scc_chan_map[idx]; */ -/* else */ -/* chan = smc_chan_map[idx]; */ - -/* cp->cp_cr = mk_cr_cmd(chan, CPM_CR_STOP_TX) | CPM_CR_FLG; */ -/* while (cp->cp_cr & CPM_CR_FLG); */ - -#endif - /* info = kmalloc(sizeof(ser_info_t), GFP_KERNEL); */ - info = &quicc_ser_info[i]; - if (info) { - memset (info, 0, sizeof(ser_info_t)); - info->magic = SERIAL_MAGIC; - info->line = i; - info->flags = state->flags; - INIT_WORK(&info->tqueue, do_softint, info); - INIT_WORK(&info->tqueue_hangup, do_serial_hangup, info); - init_waitqueue_head(&info->open_wait); - init_waitqueue_head(&info->close_wait); - info->state = state; - state->info = (struct async_struct *)info; - - /* We need to allocate a transmit and receive buffer - * descriptors from dual port ram, and a character - * buffer area from host mem. - */ - dp_addr = m360_cpm_dpalloc(sizeof(QUICC_BD) * RX_NUM_FIFO); - - /* Allocate space for FIFOs in the host memory. - * (for now this is from a static array of buffers :( - */ - /* mem_addr = m360_cpm_hostalloc(RX_NUM_FIFO * RX_BUF_SIZE); */ - /* mem_addr = kmalloc (RX_NUM_FIFO * RX_BUF_SIZE, GFP_BUFFER); */ - mem_addr = &rx_buf_pool[i * RX_NUM_FIFO * RX_BUF_SIZE]; - - /* Set the physical address of the host memory - * buffers in the buffer descriptors, and the - * virtual address for us to work with. - */ - bdp = (QUICC_BD *)((uint)pquicc + dp_addr); - info->rx_cur = info->rx_bd_base = bdp; - - /* initialize rx buffer descriptors */ - for (j=0; j<(RX_NUM_FIFO-1); j++) { - bdp->buf = &rx_buf_pool[(i * RX_NUM_FIFO + j ) * RX_BUF_SIZE]; - bdp->status = BD_SC_EMPTY | BD_SC_INTRPT; - mem_addr += RX_BUF_SIZE; - bdp++; - } - bdp->buf = &rx_buf_pool[(i * RX_NUM_FIFO + j ) * RX_BUF_SIZE]; - bdp->status = BD_SC_WRAP | BD_SC_EMPTY | BD_SC_INTRPT; - - - idx = PORT_NUM(info->state->smc_scc_num); - if (info->state->smc_scc_num & NUM_IS_SCC) { - -#if defined (CONFIG_UCQUICC) && 1 - /* set the transceiver mode to RS232 */ - sipex_mode_bits &= ~(uint)SIPEX_MODE(idx,0x0f); /* clear current mode */ - sipex_mode_bits |= (uint)SIPEX_MODE(idx,0x02); - *(uint *)_periph_base = sipex_mode_bits; - /* printk ("sipex bits = 0x%08x\n", sipex_mode_bits); */ -#endif - } - - dp_addr = m360_cpm_dpalloc(sizeof(QUICC_BD) * TX_NUM_FIFO); - - /* Allocate space for FIFOs in the host memory. - */ - /* mem_addr = m360_cpm_hostalloc(TX_NUM_FIFO * TX_BUF_SIZE); */ - /* mem_addr = kmalloc (TX_NUM_FIFO * TX_BUF_SIZE, GFP_BUFFER); */ - mem_addr = &tx_buf_pool[i * TX_NUM_FIFO * TX_BUF_SIZE]; - - /* Set the physical address of the host memory - * buffers in the buffer descriptors, and the - * virtual address for us to work with. - */ - /* bdp = (QUICC_BD *)&cp->cp_dpmem[dp_addr]; */ - bdp = (QUICC_BD *)((uint)pquicc + dp_addr); - info->tx_cur = info->tx_bd_base = (QUICC_BD *)bdp; - - /* initialize tx buffer descriptors */ - for (j=0; j<(TX_NUM_FIFO-1); j++) { - bdp->buf = &tx_buf_pool[(i * TX_NUM_FIFO + j ) * TX_BUF_SIZE]; - bdp->status = BD_SC_INTRPT; - mem_addr += TX_BUF_SIZE; - bdp++; - } - bdp->buf = &tx_buf_pool[(i * TX_NUM_FIFO + j ) * TX_BUF_SIZE]; - bdp->status = (BD_SC_WRAP | BD_SC_INTRPT); - - if (info->state->smc_scc_num & NUM_IS_SCC) { - scp = &pquicc->scc_regs[idx]; - sup = &pquicc->pram[info->state->port].scc.pscc.u; - sup->rbase = dp_addr; - sup->tbase = dp_addr; - - /* Set up the uart parameters in the - * parameter ram. - */ - sup->rfcr = SMC_EB; - sup->tfcr = SMC_EB; - - /* Set this to 1 for now, so we get single - * character interrupts. Using idle character - * time requires some additional tuning. - */ - sup->mrblr = 1; - sup->max_idl = 0; - sup->brkcr = 1; - sup->parec = 0; - sup->frmer = 0; - sup->nosec = 0; - sup->brkec = 0; - sup->uaddr1 = 0; - sup->uaddr2 = 0; - sup->toseq = 0; - { - int i; - for (i=0;i<8;i++) - sup->cc[i] = 0x8000; - } - sup->rccm = 0xc0ff; - - /* Send the CPM an initialize command. - */ - chan = scc_chan_map[idx]; - - /* execute the INIT RX & TX PARAMS command for this channel. */ - cp->cp_cr = mk_cr_cmd(chan, CPM_CR_INIT_TRX) | CPM_CR_FLG; - while (cp->cp_cr & CPM_CR_FLG); - - /* Set UART mode, 8 bit, no parity, one stop. - * Enable receive and transmit. - */ - scp->scc_gsmr.w.high = 0; - scp->scc_gsmr.w.low = - (SCC_GSMRL_MODE_UART | SCC_GSMRL_TDCR_16 | SCC_GSMRL_RDCR_16); - - /* Disable all interrupts and clear all pending - * events. - */ - scp->scc_sccm = 0; - scp->scc_scce = 0xffff; - scp->scc_dsr = 0x7e7e; - scp->scc_psmr = 0x3000; - - /* If the port is the console, enable Rx and Tx. - */ -#ifdef CONFIG_SERIAL_CONSOLE - if (i == CONFIG_SERIAL_CONSOLE_PORT) - scp->scc_gsmr.w.low |= (SCC_GSMRL_ENR | SCC_GSMRL_ENT); -#endif - } - else { - /* Configure SMCs Tx/Rx instead of port B - * parallel I/O. - */ - up = &pquicc->pram[info->state->port].scc.pothers.idma_smc.psmc.u; - up->rbase = dp_addr; - - iobits = 0xc0 << (idx * 4); - cp->pip_pbpar |= iobits; - cp->pip_pbdir &= ~iobits; - cp->pip_pbodr &= ~iobits; - - - /* Connect the baud rate generator to the - * SMC based upon index in rs_table. Also - * make sure it is connected to NMSI. - */ - cp->si_simode &= ~(0xffff << (idx * 16)); - cp->si_simode |= (i << ((idx * 16) + 12)); - - up->tbase = dp_addr; - - /* Set up the uart parameters in the - * parameter ram. - */ - up->rfcr = SMC_EB; - up->tfcr = SMC_EB; - - /* Set this to 1 for now, so we get single - * character interrupts. Using idle character - * time requires some additional tuning. - */ - up->mrblr = 1; - up->max_idl = 0; - up->brkcr = 1; - - /* Send the CPM an initialize command. - */ - chan = smc_chan_map[idx]; - - cp->cp_cr = mk_cr_cmd(chan, - CPM_CR_INIT_TRX) | CPM_CR_FLG; -#ifdef CONFIG_SERIAL_CONSOLE - if (i == CONFIG_SERIAL_CONSOLE_PORT) - printk(""); -#endif - while (cp->cp_cr & CPM_CR_FLG); - - /* Set UART mode, 8 bit, no parity, one stop. - * Enable receive and transmit. - */ - sp = &cp->smc_regs[idx]; - sp->smc_smcmr = smcr_mk_clen(9) | SMCMR_SM_UART; - - /* Disable all interrupts and clear all pending - * events. - */ - sp->smc_smcm = 0; - sp->smc_smce = 0xff; - - /* If the port is the console, enable Rx and Tx. - */ -#ifdef CONFIG_SERIAL_CONSOLE - if (i == CONFIG_SERIAL_CONSOLE_PORT) - sp->smc_smcmr |= SMCMR_REN | SMCMR_TEN; -#endif - } - - /* Install interrupt handler. - */ - /* cpm_install_handler(IRQ_MACHSPEC | state->irq, rs_360_interrupt, info); */ - /*request_irq(IRQ_MACHSPEC | state->irq, rs_360_interrupt, */ - request_irq(state->irq, rs_360_interrupt, - IRQ_FLG_LOCK, "ttyS", (void *)info); - - /* Set up the baud rate generator. - */ - m360_cpm_setbrg(i, baud_table[baud_idx]); - - } - } - - return 0; -} -module_init(rs_360_init); - -/* This must always be called before the rs_360_init() function, otherwise - * it blows away the port control information. - */ -//static int __init serial_console_setup( struct console *co, char *options) -int serial_console_setup( struct console *co, char *options) -{ - struct serial_state *ser; - uint mem_addr, dp_addr, bidx, idx, iobits; - ushort chan; - QUICC_BD *bdp; - volatile QUICC *cp; - volatile struct smc_regs *sp; - volatile struct scc_regs *scp; - volatile struct smc_uart_pram *up; - volatile struct uart_pram *sup; - -/* mleslie TODO: - * add something to the 68k bootloader to store a desired initial console baud rate */ - -/* bd_t *bd; */ /* a board info struct used by EPPC-bug */ -/* bd = (bd_t *)__res; */ - - for (bidx = 0; bidx < (sizeof(baud_table) / sizeof(int)); bidx++) - /* if (bd->bi_baudrate == baud_table[bidx]) */ - if (CONSOLE_BAUDRATE == baud_table[bidx]) - break; - - /* co->cflag = CREAD|CLOCAL|bidx|CS8; */ - baud_idx = bidx; - - ser = rs_table + CONFIG_SERIAL_CONSOLE_PORT; - - cp = pquicc; /* Get pointer to Communication Processor */ - - idx = PORT_NUM(ser->smc_scc_num); - if (ser->smc_scc_num & NUM_IS_SCC) { - - /* TODO: need to set up SCC pin assignment etc. here */ - - } - else { - iobits = 0xc0 << (idx * 4); - cp->pip_pbpar |= iobits; - cp->pip_pbdir &= ~iobits; - cp->pip_pbodr &= ~iobits; - - /* Connect the baud rate generator to the - * SMC based upon index in rs_table. Also - * make sure it is connected to NMSI. - */ - cp->si_simode &= ~(0xffff << (idx * 16)); - cp->si_simode |= (idx << ((idx * 16) + 12)); - } - - /* When we get here, the CPM has been reset, so we need - * to configure the port. - * We need to allocate a transmit and receive buffer descriptor - * from dual port ram, and a character buffer area from host mem. - */ - - /* Allocate space for two buffer descriptors in the DP ram. - */ - dp_addr = m360_cpm_dpalloc(sizeof(QUICC_BD) * CONSOLE_NUM_FIFO); - - /* Allocate space for two 2 byte FIFOs in the host memory. - */ - /* mem_addr = m360_cpm_hostalloc(8); */ - mem_addr = (uint)console_fifos; - - - /* Set the physical address of the host memory buffers in - * the buffer descriptors. - */ - /* bdp = (QUICC_BD *)&cp->cp_dpmem[dp_addr]; */ - bdp = (QUICC_BD *)((uint)pquicc + dp_addr); - bdp->buf = (char *)mem_addr; - (bdp+1)->buf = (char *)(mem_addr+4); - - /* For the receive, set empty and wrap. - * For transmit, set wrap. - */ - bdp->status = BD_SC_EMPTY | BD_SC_WRAP; - (bdp+1)->status = BD_SC_WRAP; - - /* Set up the uart parameters in the parameter ram. - */ - if (ser->smc_scc_num & NUM_IS_SCC) { - scp = &cp->scc_regs[idx]; - /* sup = (scc_uart_t *)&cp->cp_dparam[ser->port]; */ - sup = &pquicc->pram[ser->port].scc.pscc.u; - - sup->rbase = dp_addr; - sup->tbase = dp_addr + sizeof(QUICC_BD); - - /* Set up the uart parameters in the - * parameter ram. - */ - sup->rfcr = SMC_EB; - sup->tfcr = SMC_EB; - - /* Set this to 1 for now, so we get single - * character interrupts. Using idle character - * time requires some additional tuning. - */ - sup->mrblr = 1; - sup->max_idl = 0; - sup->brkcr = 1; - sup->parec = 0; - sup->frmer = 0; - sup->nosec = 0; - sup->brkec = 0; - sup->uaddr1 = 0; - sup->uaddr2 = 0; - sup->toseq = 0; - { - int i; - for (i=0;i<8;i++) - sup->cc[i] = 0x8000; - } - sup->rccm = 0xc0ff; - - /* Send the CPM an initialize command. - */ - chan = scc_chan_map[idx]; - - cp->cp_cr = mk_cr_cmd(chan, CPM_CR_INIT_TRX) | CPM_CR_FLG; - while (cp->cp_cr & CPM_CR_FLG); - - /* Set UART mode, 8 bit, no parity, one stop. - * Enable receive and transmit. - */ - scp->scc_gsmr.w.high = 0; - scp->scc_gsmr.w.low = - (SCC_GSMRL_MODE_UART | SCC_GSMRL_TDCR_16 | SCC_GSMRL_RDCR_16); - - /* Disable all interrupts and clear all pending - * events. - */ - scp->scc_sccm = 0; - scp->scc_scce = 0xffff; - scp->scc_dsr = 0x7e7e; - scp->scc_psmr = 0x3000; - - scp->scc_gsmr.w.low |= (SCC_GSMRL_ENR | SCC_GSMRL_ENT); - - } - else { - /* up = (smc_uart_t *)&cp->cp_dparam[ser->port]; */ - up = &pquicc->pram[ser->port].scc.pothers.idma_smc.psmc.u; - - up->rbase = dp_addr; /* Base of receive buffer desc. */ - up->tbase = dp_addr+sizeof(QUICC_BD); /* Base of xmt buffer desc. */ - up->rfcr = SMC_EB; - up->tfcr = SMC_EB; - - /* Set this to 1 for now, so we get single character interrupts. - */ - up->mrblr = 1; /* receive buffer length */ - up->max_idl = 0; /* wait forever for next char */ - - /* Send the CPM an initialize command. - */ - chan = smc_chan_map[idx]; - cp->cp_cr = mk_cr_cmd(chan, CPM_CR_INIT_TRX) | CPM_CR_FLG; - while (cp->cp_cr & CPM_CR_FLG); - - /* Set UART mode, 8 bit, no parity, one stop. - * Enable receive and transmit. - */ - sp = &cp->smc_regs[idx]; - sp->smc_smcmr = smcr_mk_clen(9) | SMCMR_SM_UART; - - /* And finally, enable Rx and Tx. - */ - sp->smc_smcmr |= SMCMR_REN | SMCMR_TEN; - } - - /* Set up the baud rate generator. - */ - /* m360_cpm_setbrg((ser - rs_table), bd->bi_baudrate); */ - m360_cpm_setbrg((ser - rs_table), CONSOLE_BAUDRATE); - - return 0; -} - -/* - * Local variables: - * c-indent-level: 4 - * c-basic-offset: 4 - * tab-width: 4 - * End: - */ |