diff options
Diffstat (limited to 'drivers/scsi/qla2xxx/qla_fw.h')
| -rw-r--r-- | drivers/scsi/qla2xxx/qla_fw.h | 294 |
1 files changed, 291 insertions, 3 deletions
diff --git a/drivers/scsi/qla2xxx/qla_fw.h b/drivers/scsi/qla2xxx/qla_fw.h index ee1f1e794c2..7abb045a041 100644 --- a/drivers/scsi/qla2xxx/qla_fw.h +++ b/drivers/scsi/qla2xxx/qla_fw.h @@ -1215,9 +1215,10 @@ struct qla_fdt_layout { struct qla_flt_location { uint8_t sig[4]; - uint32_t start_lo; - uint32_t start_hi; - uint16_t unused; + uint16_t start_lo; + uint16_t start_hi; + uint8_t version; + uint8_t unused[5]; uint16_t checksum; }; @@ -1390,4 +1391,291 @@ struct access_chip_rsp_84xx { uint32_t reserved[12]; }; + +/* 81XX Support **************************************************************/ + +#define MBA_DCBX_START 0x8016 +#define MBA_DCBX_COMPLETE 0x8030 +#define MBA_FCF_CONF_ERR 0x8031 +#define MBA_DCBX_PARAM_UPDATE 0x8032 +#define MBA_IDC_COMPLETE 0x8100 +#define MBA_IDC_NOTIFY 0x8101 +#define MBA_IDC_TIME_EXT 0x8102 + +struct nvram_81xx { + /* NVRAM header. */ + uint8_t id[4]; + uint16_t nvram_version; + uint16_t reserved_0; + + /* Firmware Initialization Control Block. */ + uint16_t version; + uint16_t reserved_1; + uint16_t frame_payload_size; + uint16_t execution_throttle; + uint16_t exchange_count; + uint16_t reserved_2; + + uint8_t port_name[WWN_SIZE]; + uint8_t node_name[WWN_SIZE]; + + uint16_t login_retry_count; + uint16_t reserved_3; + uint16_t interrupt_delay_timer; + uint16_t login_timeout; + + uint32_t firmware_options_1; + uint32_t firmware_options_2; + uint32_t firmware_options_3; + + uint16_t reserved_4[4]; + + /* Offset 64. */ + uint8_t enode_mac[6]; + uint16_t reserved_5[5]; + + /* Offset 80. */ + uint16_t reserved_6[24]; + + /* Offset 128. */ + uint16_t reserved_7[64]; + + /* + * BIT 0 = Enable spinup delay + * BIT 1 = Disable BIOS + * BIT 2 = Enable Memory Map BIOS + * BIT 3 = Enable Selectable Boot + * BIT 4 = Disable RISC code load + * BIT 5 = Disable Serdes + * BIT 6 = Opt boot mode + * BIT 7 = Interrupt enable + * + * BIT 8 = EV Control enable + * BIT 9 = Enable lip reset + * BIT 10 = Enable lip full login + * BIT 11 = Enable target reset + * BIT 12 = Stop firmware + * BIT 13 = Enable nodename option + * BIT 14 = Default WWPN valid + * BIT 15 = Enable alternate WWN + * + * BIT 16 = CLP LUN string + * BIT 17 = CLP Target string + * BIT 18 = CLP BIOS enable string + * BIT 19 = CLP Serdes string + * BIT 20 = CLP WWPN string + * BIT 21 = CLP WWNN string + * BIT 22 = + * BIT 23 = + * BIT 24 = Keep WWPN + * BIT 25 = Temp WWPN + * BIT 26-31 = + */ + uint32_t host_p; + + uint8_t alternate_port_name[WWN_SIZE]; + uint8_t alternate_node_name[WWN_SIZE]; + + uint8_t boot_port_name[WWN_SIZE]; + uint16_t boot_lun_number; + uint16_t reserved_8; + + uint8_t alt1_boot_port_name[WWN_SIZE]; + uint16_t alt1_boot_lun_number; + uint16_t reserved_9; + + uint8_t alt2_boot_port_name[WWN_SIZE]; + uint16_t alt2_boot_lun_number; + uint16_t reserved_10; + + uint8_t alt3_boot_port_name[WWN_SIZE]; + uint16_t alt3_boot_lun_number; + uint16_t reserved_11; + + /* + * BIT 0 = Selective Login + * BIT 1 = Alt-Boot Enable + * BIT 2 = Reserved + * BIT 3 = Boot Order List + * BIT 4 = Reserved + * BIT 5 = Selective LUN + * BIT 6 = Reserved + * BIT 7-31 = + */ + uint32_t efi_parameters; + + uint8_t reset_delay; + uint8_t reserved_12; + uint16_t reserved_13; + + uint16_t boot_id_number; + uint16_t reserved_14; + + uint16_t max_luns_per_target; + uint16_t reserved_15; + + uint16_t port_down_retry_count; + uint16_t link_down_timeout; + + /* FCode parameters. */ + uint16_t fcode_parameter; + + uint16_t reserved_16[3]; + + /* Offset 352. */ + uint8_t reserved_17[4]; + uint16_t reserved_18[5]; + uint8_t reserved_19[2]; + uint16_t reserved_20[8]; + + /* Offset 384. */ + uint8_t reserved_21[16]; + uint16_t reserved_22[8]; + + /* Offset 416. */ + uint16_t reserved_23[32]; + + /* Offset 480. */ + uint8_t model_name[16]; + + /* Offset 496. */ + uint16_t feature_mask_l; + uint16_t feature_mask_h; + uint16_t reserved_24[2]; + + uint16_t subsystem_vendor_id; + uint16_t subsystem_device_id; + + uint32_t checksum; +}; + +/* + * ISP Initialization Control Block. + * Little endian except where noted. + */ +#define ICB_VERSION 1 +struct init_cb_81xx { + uint16_t version; + uint16_t reserved_1; + + uint16_t frame_payload_size; + uint16_t execution_throttle; + uint16_t exchange_count; + + uint16_t reserved_2; + + uint8_t port_name[WWN_SIZE]; /* Big endian. */ + uint8_t node_name[WWN_SIZE]; /* Big endian. */ + + uint16_t response_q_inpointer; + uint16_t request_q_outpointer; + + uint16_t login_retry_count; + + uint16_t prio_request_q_outpointer; + + uint16_t response_q_length; + uint16_t request_q_length; + + uint16_t reserved_3; + + uint16_t prio_request_q_length; + + uint32_t request_q_address[2]; + uint32_t response_q_address[2]; + uint32_t prio_request_q_address[2]; + + uint8_t reserved_4[8]; + + uint16_t atio_q_inpointer; + uint16_t atio_q_length; + uint32_t atio_q_address[2]; + + uint16_t interrupt_delay_timer; /* 100us increments. */ + uint16_t login_timeout; + + /* + * BIT 0-3 = Reserved + * BIT 4 = Enable Target Mode + * BIT 5 = Disable Initiator Mode + * BIT 6 = Reserved + * BIT 7 = Reserved + * + * BIT 8-13 = Reserved + * BIT 14 = Node Name Option + * BIT 15-31 = Reserved + */ + uint32_t firmware_options_1; + + /* + * BIT 0 = Operation Mode bit 0 + * BIT 1 = Operation Mode bit 1 + * BIT 2 = Operation Mode bit 2 + * BIT 3 = Operation Mode bit 3 + * BIT 4-7 = Reserved + * + * BIT 8 = Enable Class 2 + * BIT 9 = Enable ACK0 + * BIT 10 = Reserved + * BIT 11 = Enable FC-SP Security + * BIT 12 = FC Tape Enable + * BIT 13 = Reserved + * BIT 14 = Enable Target PRLI Control + * BIT 15-31 = Reserved + */ + uint32_t firmware_options_2; + + /* + * BIT 0-3 = Reserved + * BIT 4 = FCP RSP Payload bit 0 + * BIT 5 = FCP RSP Payload bit 1 + * BIT 6 = Enable Receive Out-of-Order data frame handling + * BIT 7 = Reserved + * + * BIT 8 = Reserved + * BIT 9 = Enable Out-of-Order FCP_XFER_RDY relative offset handling + * BIT 10-16 = Reserved + * BIT 17 = Enable multiple FCFs + * BIT 18-20 = MAC addressing mode + * BIT 21-25 = Ethernet data rate + * BIT 26 = Enable ethernet header rx IOCB for ATIO q + * BIT 27 = Enable ethernet header rx IOCB for response q + * BIT 28 = SPMA selection bit 0 + * BIT 28 = SPMA selection bit 1 + * BIT 30-31 = Reserved + */ + uint32_t firmware_options_3; + + uint8_t reserved_5[8]; + + uint8_t enode_mac[6]; + + uint8_t reserved_6[10]; +}; + +struct mid_init_cb_81xx { + struct init_cb_81xx init_cb; + + uint16_t count; + uint16_t options; + + struct mid_conf_entry_24xx entries[MAX_MULTI_ID_FABRIC]; +}; + +#define FARX_ACCESS_FLASH_CONF_81XX 0x7FFD0000 +#define FARX_ACCESS_FLASH_DATA_81XX 0x7F800000 + +/* 81XX Flash locations -- occupies second 2MB region. */ +#define FA_BOOT_CODE_ADDR_81 0x80000 +#define FA_RISC_CODE_ADDR_81 0xA0000 +#define FA_FW_AREA_ADDR_81 0xC0000 +#define FA_VPD_NVRAM_ADDR_81 0xD0000 +#define FA_FEATURE_ADDR_81 0xD4000 +#define FA_FLASH_DESCR_ADDR_81 0xD8000 +#define FA_FLASH_LAYOUT_ADDR_81 0xD8400 +#define FA_HW_EVENT0_ADDR_81 0xDC000 +#define FA_HW_EVENT1_ADDR_81 0xDC400 +#define FA_NPIV_CONF0_ADDR_81 0xD1000 +#define FA_NPIV_CONF1_ADDR_81 0xD2000 + #endif |