diff options
Diffstat (limited to 'drivers/scsi/isci/probe_roms.h')
| -rw-r--r-- | drivers/scsi/isci/probe_roms.h | 89 |
1 files changed, 86 insertions, 3 deletions
diff --git a/drivers/scsi/isci/probe_roms.h b/drivers/scsi/isci/probe_roms.h index 2c75248ca32..bb0e9d4d97c 100644 --- a/drivers/scsi/isci/probe_roms.h +++ b/drivers/scsi/isci/probe_roms.h @@ -152,7 +152,7 @@ struct sci_user_parameters { #define MAX_CONCURRENT_DEVICE_SPIN_UP_COUNT 4 struct sci_oem_params; -int sci_oem_parameters_validate(struct sci_oem_params *oem); +int sci_oem_parameters_validate(struct sci_oem_params *oem, u8 version); struct isci_orom; struct isci_orom *isci_request_oprom(struct pci_dev *pdev); @@ -191,6 +191,11 @@ struct isci_oem_hdr { 0x1a, 0x04, 0xc6) #define ISCI_EFI_VAR_NAME "RstScuO" +#define ISCI_ROM_VER_1_0 0x10 +#define ISCI_ROM_VER_1_1 0x11 +#define ISCI_ROM_VER_1_3 0x13 +#define ISCI_ROM_VER_LATEST ISCI_ROM_VER_1_3 + /* Allowed PORT configuration modes APC Automatic PORT configuration mode is * defined by the OEM configuration parameters providing no PHY_MASK parameters * for any PORT. i.e. There are no phys assigned to any of the ports at start. @@ -220,8 +225,86 @@ struct sci_oem_params { struct { uint8_t mode_type; uint8_t max_concurr_spin_up; - uint8_t do_enable_ssc; - uint8_t reserved; + /* + * This bitfield indicates the OEM's desired default Tx + * Spread Spectrum Clocking (SSC) settings for SATA and SAS. + * NOTE: Default SSC Modulation Frequency is 31.5KHz. + */ + union { + struct { + /* + * NOTE: Max spread for SATA is +0 / -5000 PPM. + * Down-spreading SSC (only method allowed for SATA): + * SATA SSC Tx Disabled = 0x0 + * SATA SSC Tx at +0 / -1419 PPM Spread = 0x2 + * SATA SSC Tx at +0 / -2129 PPM Spread = 0x3 + * SATA SSC Tx at +0 / -4257 PPM Spread = 0x6 + * SATA SSC Tx at +0 / -4967 PPM Spread = 0x7 + */ + uint8_t ssc_sata_tx_spread_level:4; + /* + * SAS SSC Tx Disabled = 0x0 + * + * NOTE: Max spread for SAS down-spreading +0 / + * -2300 PPM + * Down-spreading SSC: + * SAS SSC Tx at +0 / -1419 PPM Spread = 0x2 + * SAS SSC Tx at +0 / -2129 PPM Spread = 0x3 + * + * NOTE: Max spread for SAS center-spreading +2300 / + * -2300 PPM + * Center-spreading SSC: + * SAS SSC Tx at +1064 / -1064 PPM Spread = 0x3 + * SAS SSC Tx at +2129 / -2129 PPM Spread = 0x6 + */ + uint8_t ssc_sas_tx_spread_level:3; + /* + * NOTE: Refer to the SSC section of the SAS 2.x + * Specification for proper setting of this field. + * For standard SAS Initiator SAS PHY operation it + * should be 0 for Down-spreading. + * SAS SSC Tx spread type: + * Down-spreading SSC = 0 + * Center-spreading SSC = 1 + */ + uint8_t ssc_sas_tx_type:1; + }; + uint8_t do_enable_ssc; + }; + /* + * This field indicates length of the SAS/SATA cable between + * host and device. + * This field is used make relationship between analog + * parameters of the phy in the silicon and length of the cable. + * Supported cable attenuation levels: + * "short"- up to 3m, "medium"-3m to 6m, and "long"- more than + * 6m. + * + * This is bit mask field: + * + * BIT: (MSB) 7 6 5 4 + * ASSIGNMENT: <phy3><phy2><phy1><phy0> - Medium cable + * length assignment + * BIT: 3 2 1 0 (LSB) + * ASSIGNMENT: <phy3><phy2><phy1><phy0> - Long cable length + * assignment + * + * BITS 7-4 are set when the cable length is assigned to medium + * BITS 3-0 are set when the cable length is assigned to long + * + * The BIT positions are clear when the cable length is + * assigned to short. + * + * Setting the bits for both long and medium cable length is + * undefined. + * + * A value of 0x84 would assign + * phy3 - medium + * phy2 - long + * phy1 - short + * phy0 - short + */ + uint8_t cable_selection_mask; } controller; struct { |