diff options
Diffstat (limited to 'drivers/scsi/aic7xxx/aic79xx.seq')
| -rw-r--r-- | drivers/scsi/aic7xxx/aic79xx.seq | 18 |
1 files changed, 9 insertions, 9 deletions
diff --git a/drivers/scsi/aic7xxx/aic79xx.seq b/drivers/scsi/aic7xxx/aic79xx.seq index 2fb78e35a9e..3a36d9362a1 100644 --- a/drivers/scsi/aic7xxx/aic79xx.seq +++ b/drivers/scsi/aic7xxx/aic79xx.seq @@ -567,7 +567,7 @@ BEGIN_CRITICAL; shr SELOID, 4, SCB_SCSIID; /* * If we want to send a message to the device, ensure - * we are selecting with atn irregardless of our packetized + * we are selecting with atn regardless of our packetized * agreement. Since SPI4 only allows target reset or PPR * messages if this is a packetized connection, the change * to our negotiation table entry for this selection will @@ -960,7 +960,7 @@ p_status_okay: * This is done to allow the host to send messages outside of an identify * sequence while protecting the seqencer from testing the MK_MESSAGE bit * on an SCB that might not be for the current nexus. (For example, a - * BDR message in responce to a bad reselection would leave us pointed to + * BDR message in response to a bad reselection would leave us pointed to * an SCB that doesn't have anything to do with the current target). * * Otherwise, treat MSG_OUT as a 1 byte message to send (abort, abort tag, @@ -1507,7 +1507,7 @@ service_fifo: * If the other FIFO needs loading, then it * must not have claimed the S/G cache yet * (SG_CACHE_AVAIL would have been cleared in - * the orginal FIFO mode and we test this above). + * the original FIFO mode and we test this above). * Return to the idle loop so we can process the * FIFO not currently on the bus first. */ @@ -1521,7 +1521,7 @@ idle_sgfetch_okay: idle_sgfetch_start: /* * We fetch a "cacheline aligned" and sized amount of data - * so we don't end up referencing a non-existant page. + * so we don't end up referencing a non-existent page. * Cacheline aligned is in quotes because the kernel will * set the prefetch amount to a reasonable level if the * cacheline size is unknown. @@ -1551,7 +1551,7 @@ idle_sg_avail: test DFSTATUS, PRELOAD_AVAIL jz return; /* * On the A, preloading a segment before HDMAENACK - * comes true can clobber the shaddow address of the + * comes true can clobber the shadow address of the * first segment in the S/G FIFO. Wait until it is * safe to proceed. */ @@ -2004,10 +2004,10 @@ pkt_handle_xfer: * Defer handling of this NONPACKREQ until we * can be sure it pertains to this FIFO. SAVEPTRS * will not be asserted if the NONPACKREQ is for us, - * so we must simulate it if shaddow is valid. If - * shaddow is not valid, keep running this FIFO until we + * so we must simulate it if shadow is valid. If + * shadow is not valid, keep running this FIFO until we * have satisfied the transfer by loading segments and - * waiting for either shaddow valid or last_seg_done. + * waiting for either shadow valid or last_seg_done. */ test MDFFSTAT, SHVALID jnz pkt_saveptrs; pkt_service_fifo: @@ -2171,7 +2171,7 @@ pkt_status_check_nonpackreq: /* * The unexpected nonpkt phase handler assumes that any * data channel use will have a FIFO reference count. It - * turns out that the status handler doesn't need a refernce + * turns out that the status handler doesn't need a references * count since the status received flag, and thus completion * processing, cannot be set until the handler is finished. * We increment the count here to make the nonpkt handler |