diff options
Diffstat (limited to 'drivers/scsi/aic7xxx/aic79xx.reg')
| -rw-r--r-- | drivers/scsi/aic7xxx/aic79xx.reg | 3958 |
1 files changed, 3958 insertions, 0 deletions
diff --git a/drivers/scsi/aic7xxx/aic79xx.reg b/drivers/scsi/aic7xxx/aic79xx.reg new file mode 100644 index 00000000000..cca58edc864 --- /dev/null +++ b/drivers/scsi/aic7xxx/aic79xx.reg @@ -0,0 +1,3958 @@ +/* + * Aic79xx register and scratch ram definitions. + * + * Copyright (c) 1994-2001 Justin T. Gibbs. + * Copyright (c) 2000-2002 Adaptec Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + * $FreeBSD$ + */ +VERSION = "$Id: //depot/aic7xxx/aic7xxx/aic79xx.reg#70 $" + +/* + * This file is processed by the aic7xxx_asm utility for use in assembling + * firmware for the aic79xx family of SCSI host adapters as well as to generate + * a C header file for use in the kernel portion of the Aic79xx driver. + */ + +/* Register window Modes */ +#define M_DFF0 0 +#define M_DFF1 1 +#define M_CCHAN 2 +#define M_SCSI 3 +#define M_CFG 4 +#define M_DST_SHIFT 4 + +#define MK_MODE(src, dst) ((src) | ((dst) << M_DST_SHIFT)) +#define SET_MODE(src, dst) \ + SET_SRC_MODE src; \ + SET_DST_MODE dst; \ + if ((ahd->bugs & AHD_SET_MODE_BUG) != 0) { \ + mvi MK_MODE(src, dst) call set_mode_work_around; \ + } else { \ + mvi MODE_PTR, MK_MODE(src, dst); \ + } + +#define TOGGLE_DFF_MODE \ + if ((ahd->bugs & AHD_SET_MODE_BUG) != 0) { \ + call toggle_dff_mode_work_around; \ + } else { \ + xor MODE_PTR, MK_MODE(M_DFF1, M_DFF1); \ + } + +#define RESTORE_MODE(mode) \ + if ((ahd->bugs & AHD_SET_MODE_BUG) != 0) { \ + mov mode call set_mode_work_around; \ + } else { \ + mov MODE_PTR, mode; \ + } + +#define SET_SEQINTCODE(code) \ + if ((ahd->bugs & AHD_INTCOLLISION_BUG) != 0) { \ + mvi code call set_seqint_work_around; \ + } else { \ + mvi SEQINTCODE, code; \ + } + +/* + * Mode Pointer + * Controls which of the 5, 512byte, address spaces should be used + * as the source and destination of any register accesses in our + * register window. + */ +register MODE_PTR { + address 0x000 + access_mode RW + field DST_MODE 0x70 + field SRC_MODE 0x07 + mode_pointer +} + +const SRC_MODE_SHIFT 0 +const DST_MODE_SHIFT 4 + +/* + * Host Interrupt Status + */ +register INTSTAT { + address 0x001 + access_mode RW + field HWERRINT 0x80 + field BRKADRINT 0x40 + field SWTMINT 0x20 + field PCIINT 0x10 + field SCSIINT 0x08 + field SEQINT 0x04 + field CMDCMPLT 0x02 + field SPLTINT 0x01 + mask INT_PEND 0xFF +} + +/* + * Sequencer Interrupt Code + */ +register SEQINTCODE { + address 0x002 + access_mode RW + field { + NO_SEQINT, /* No seqint pending. */ + BAD_PHASE, /* unknown scsi bus phase */ + SEND_REJECT, /* sending a message reject */ + PROTO_VIOLATION, /* Protocol Violation */ + NO_MATCH, /* no cmd match for reconnect */ + IGN_WIDE_RES, /* Complex IGN Wide Res Msg */ + PDATA_REINIT, /* + * Returned to data phase + * that requires data + * transfer pointers to be + * recalculated from the + * transfer residual. + */ + HOST_MSG_LOOP, /* + * The bus is ready for the + * host to perform another + * message transaction. This + * mechanism is used for things + * like sync/wide negotiation + * that require a kernel based + * message state engine. + */ + BAD_STATUS, /* Bad status from target */ + DATA_OVERRUN, /* + * Target attempted to write + * beyond the bounds of its + * command. + */ + MKMSG_FAILED, /* + * Target completed command + * without honoring our ATN + * request to issue a message. + */ + MISSED_BUSFREE, /* + * The sequencer never saw + * the bus go free after + * either a command complete + * or disconnect message. + */ + DUMP_CARD_STATE, + ILLEGAL_PHASE, + INVALID_SEQINT, + CFG4ISTAT_INTR, + STATUS_OVERRUN, + CFG4OVERRUN, + ENTERING_NONPACK, + TASKMGMT_FUNC_COMPLETE, /* + * Task management function + * request completed with + * an expected busfree. + */ + TASKMGMT_CMD_CMPLT_OKAY, /* + * A command with a non-zero + * task management function + * has completed via the normal + * command completion method + * for commands with a zero + * task management function. + * This happens when an attempt + * to abort a command loses + * the race for the command to + * complete normally. + */ + TRACEPOINT0, + TRACEPOINT1, + TRACEPOINT2, + TRACEPOINT3, + SAW_HWERR, + BAD_SCB_STATUS + } +} + +/* + * Clear Host Interrupt + */ +register CLRINT { + address 0x003 + access_mode WO + field CLRHWERRINT 0x80 /* Rev B or greater */ + field CLRBRKADRINT 0x40 + field CLRSWTMINT 0x20 + field CLRPCIINT 0x10 + field CLRSCSIINT 0x08 + field CLRSEQINT 0x04 + field CLRCMDINT 0x02 + field CLRSPLTINT 0x01 +} + +/* + * Error Register + */ +register ERROR { + address 0x004 + access_mode RO + field CIOPARERR 0x80 + field CIOACCESFAIL 0x40 /* Rev B or greater */ + field MPARERR 0x20 + field DPARERR 0x10 + field SQPARERR 0x08 + field ILLOPCODE 0x04 + field DSCTMOUT 0x02 +} + +/* + * Clear Error + */ +register CLRERR { + address 0x004 + access_mode WO + field CLRCIOPARERR 0x80 + field CLRCIOACCESFAIL 0x40 /* Rev B or greater */ + field CLRMPARERR 0x20 + field CLRDPARERR 0x10 + field CLRSQPARERR 0x08 + field CLRILLOPCODE 0x04 + field CLRDSCTMOUT 0x02 +} + +/* + * Host Control Register + * Overall host control of the device. + */ +register HCNTRL { + address 0x005 + access_mode RW + field SEQ_RESET 0x80 /* Rev B or greater */ + field POWRDN 0x40 + field SWINT 0x10 + field SWTIMER_START_B 0x08 /* Rev B or greater */ + field PAUSE 0x04 + field INTEN 0x02 + field CHIPRST 0x01 + field CHIPRSTACK 0x01 +} + +/* + * Host New SCB Queue Offset + */ +register HNSCB_QOFF { + address 0x006 + access_mode RW + size 2 +} + +/* + * Host Empty SCB Queue Offset + */ +register HESCB_QOFF { + address 0x008 + access_mode RW +} + +/* + * Host Mailbox + */ +register HS_MAILBOX { + address 0x00B + access_mode RW + mask HOST_TQINPOS 0x80 /* Boundary at either 0 or 128 */ + mask ENINT_COALESCE 0x40 /* Perform interrupt coalescing */ +} + +/* + * Sequencer Interupt Status + */ +register SEQINTSTAT { + address 0x00C + access_mode RO + field SEQ_SWTMRTO 0x10 + field SEQ_SEQINT 0x08 + field SEQ_SCSIINT 0x04 + field SEQ_PCIINT 0x02 + field SEQ_SPLTINT 0x01 +} + +/* + * Clear SEQ Interrupt + */ +register CLRSEQINTSTAT { + address 0x00C + access_mode WO + field CLRSEQ_SWTMRTO 0x10 + field CLRSEQ_SEQINT 0x08 + field CLRSEQ_SCSIINT 0x04 + field CLRSEQ_PCIINT 0x02 + field CLRSEQ_SPLTINT 0x01 +} + +/* + * Software Timer + */ +register SWTIMER { + address 0x00E + access_mode RW + size 2 +} + +/* + * SEQ New SCB Queue Offset + */ +register SNSCB_QOFF { + address 0x010 + access_mode RW + size 2 + modes M_CCHAN +} + +/* + * SEQ Empty SCB Queue Offset + */ +register SESCB_QOFF { + address 0x012 + access_mode RW + modes M_CCHAN +} + +/* + * SEQ Done SCB Queue Offset + */ +register SDSCB_QOFF { + address 0x014 + access_mode RW + modes M_CCHAN + size 2 +} + +/* + * Queue Offset Control & Status + */ +register QOFF_CTLSTA { + address 0x016 + access_mode RW + modes M_CCHAN + field EMPTY_SCB_AVAIL 0x80 + field NEW_SCB_AVAIL 0x40 + field SDSCB_ROLLOVR 0x20 + field HS_MAILBOX_ACT 0x10 + field SCB_QSIZE 0x0F { + SCB_QSIZE_4, + SCB_QSIZE_8, + SCB_QSIZE_16, + SCB_QSIZE_32, + SCB_QSIZE_64, + SCB_QSIZE_128, + SCB_QSIZE_256, + SCB_QSIZE_512, + SCB_QSIZE_1024, + SCB_QSIZE_2048, + SCB_QSIZE_4096, + SCB_QSIZE_8192, + SCB_QSIZE_16384 + } +} + +/* + * Interrupt Control + */ +register INTCTL { + address 0x018 + access_mode RW + field SWTMINTMASK 0x80 + field SWTMINTEN 0x40 + field SWTIMER_START 0x20 + field AUTOCLRCMDINT 0x10 + field PCIINTEN 0x08 + field SCSIINTEN 0x04 + field SEQINTEN 0x02 + field SPLTINTEN 0x01 +} + +/* + * Data FIFO Control + */ +register DFCNTRL { + address 0x019 + access_mode RW + modes M_DFF0, M_DFF1 + field PRELOADEN 0x80 + field SCSIENWRDIS 0x40 /* Rev B only. */ + field SCSIEN 0x20 + field SCSIENACK 0x20 + field HDMAEN 0x08 + field HDMAENACK 0x08 + field DIRECTION 0x04 + field DIRECTIONACK 0x04 + field FIFOFLUSH 0x02 + field FIFOFLUSHACK 0x02 + field DIRECTIONEN 0x01 +} + +/* + * Device Space Command 0 + */ +register DSCOMMAND0 { + address 0x019 + access_mode RW + modes M_CFG + field CACHETHEN 0x80 /* Cache Threshold enable */ + field DPARCKEN 0x40 /* Data Parity Check Enable */ + field MPARCKEN 0x20 /* Memory Parity Check Enable */ + field EXTREQLCK 0x10 /* External Request Lock */ + field DISABLE_TWATE 0x02 /* Rev B or greater */ + field CIOPARCKEN 0x01 /* Internal bus parity error enable */ +} + +/* + * Data FIFO Status + */ +register DFSTATUS { + address 0x01A + access_mode RO + modes M_DFF0, M_DFF1 + field PRELOAD_AVAIL 0x80 + field PKT_PRELOAD_AVAIL 0x40 + field MREQPEND 0x10 + field HDONE 0x08 + field DFTHRESH 0x04 + field FIFOFULL 0x02 + field FIFOEMP 0x01 +} + +/* + * S/G Cache Pointer + */ +register SG_CACHE_PRE { + address 0x01B + access_mode WO + modes M_DFF0, M_DFF1 + field SG_ADDR_MASK 0xf8 + field ODD_SEG 0x04 + field LAST_SEG 0x02 +} + +register SG_CACHE_SHADOW { + address 0x01B + access_mode RO + modes M_DFF0, M_DFF1 + field SG_ADDR_MASK 0xf8 + field ODD_SEG 0x04 + field LAST_SEG 0x02 + field LAST_SEG_DONE 0x01 +} + +/* + * Arbiter Control + */ +register ARBCTL { + address 0x01B + access_mode RW + modes M_CFG + field RESET_HARB 0x80 + field RETRY_SWEN 0x08 + field USE_TIME 0x07 +} + +/* + * Data Channel Host Address + */ +register HADDR { + address 0x070 + access_mode RW + size 8 + modes M_DFF0, M_DFF1 +} + +/* + * Host Overlay DMA Address + */ +register HODMAADR { + address 0x070 + access_mode RW + size 8 + modes M_SCSI +} + +/* + * PCI PLL Delay. + */ +register PLLDELAY { + address 0x070 + access_mode RW + size 1 + modes M_CFG + field SPLIT_DROP_REQ 0x80 +} + +/* + * Data Channel Host Count + */ +register HCNT { + address 0x078 + access_mode RW + size 3 + modes M_DFF0, M_DFF1 +} + +/* + * Host Overlay DMA Count + */ +register HODMACNT { + address 0x078 + access_mode RW + size 2 + modes M_SCSI +} + +/* + * Host Overlay DMA Enable + */ +register HODMAEN { + address 0x07A + access_mode RW + modes M_SCSI +} + +/* + * Scatter/Gather Host Address + */ +register SGHADDR { + address 0x07C + access_mode RW + size 8 + modes M_DFF0, M_DFF1 +} + +/* + * SCB Host Address + */ +register SCBHADDR { + address 0x07C + access_mode RW + size 8 + modes M_CCHAN +} + +/* + * Scatter/Gather Host Count + */ +register SGHCNT { + address 0x084 + access_mode RW + modes M_DFF0, M_DFF1 +} + +/* + * SCB Host Count + */ +register SCBHCNT { + address 0x084 + access_mode RW + modes M_CCHAN +} + +/* + * Data FIFO Threshold + */ +register DFF_THRSH { + address 0x088 + access_mode RW + modes M_CFG + field WR_DFTHRSH 0x70 { + WR_DFTHRSH_MIN, + WR_DFTHRSH_25, + WR_DFTHRSH_50, + WR_DFTHRSH_63, + WR_DFTHRSH_75, + WR_DFTHRSH_85, + WR_DFTHRSH_90, + WR_DFTHRSH_MAX + } + field RD_DFTHRSH 0x07 { + RD_DFTHRSH_MIN, + RD_DFTHRSH_25, + RD_DFTHRSH_50, + RD_DFTHRSH_63, + RD_DFTHRSH_75, + RD_DFTHRSH_85, + RD_DFTHRSH_90, + RD_DFTHRSH_MAX + } +} + +/* + * ROM Address + */ +register ROMADDR { + address 0x08A + access_mode RW + size 3 +} + +/* + * ROM Control + */ +register ROMCNTRL { + address 0x08D + access_mode RW + field ROMOP 0xE0 + field ROMSPD 0x18 + field REPEAT 0x02 + field RDY 0x01 +} + +/* + * ROM Data + */ +register ROMDATA { + address 0x08E + access_mode RW +} + +/* + * Data Channel Receive Message 0 + */ +register DCHRXMSG0 { + address 0x090 + access_mode RO + modes M_DFF0, M_DFF1 + field CDNUM 0xF8 + field CFNUM 0x07 +} + +/* + * CMC Recieve Message 0 + */ +register CMCRXMSG0 { + address 0x090 + access_mode RO + modes M_CCHAN + field CDNUM 0xF8 + field CFNUM 0x07 +} + +/* + * Overlay Recieve Message 0 + */ +register OVLYRXMSG0 { + address 0x090 + access_mode RO + modes M_SCSI + field CDNUM 0xF8 + field CFNUM 0x07 +} + +/* + * Relaxed Order Enable + */ +register ROENABLE { + address 0x090 + access_mode RW + modes M_CFG + field MSIROEN 0x20 + field OVLYROEN 0x10 + field CMCROEN 0x08 + field SGROEN 0x04 + field DCH1ROEN 0x02 + field DCH0ROEN 0x01 +} + +/* + * Data Channel Receive Message 1 + */ +register DCHRXMSG1 { + address 0x091 + access_mode RO + modes M_DFF0, M_DFF1 + field CBNUM 0xFF +} + +/* + * CMC Recieve Message 1 + */ +register CMCRXMSG1 { + address 0x091 + access_mode RO + modes M_CCHAN + field CBNUM 0xFF +} + +/* + * Overlay Recieve Message 1 + */ +register OVLYRXMSG1 { + address 0x091 + access_mode RO + modes M_SCSI + field CBNUM 0xFF +} + +/* + * No Snoop Enable + */ +register NSENABLE { + address 0x091 + access_mode RW + modes M_CFG + field MSINSEN 0x20 + field OVLYNSEN 0x10 + field CMCNSEN 0x08 + field SGNSEN 0x04 + field DCH1NSEN 0x02 + field DCH0NSEN 0x01 +} + +/* + * Data Channel Receive Message 2 + */ +register DCHRXMSG2 { + address 0x092 + access_mode RO + modes M_DFF0, M_DFF1 + field MINDEX 0xFF +} + +/* + * CMC Recieve Message 2 + */ +register CMCRXMSG2 { + address 0x092 + access_mode RO + modes M_CCHAN + field MINDEX 0xFF +} + +/* + * Overlay Recieve Message 2 + */ +register OVLYRXMSG2 { + address 0x092 + access_mode RO + modes M_SCSI + field MINDEX 0xFF +} + +/* + * Outstanding Split Transactions + */ +register OST { + address 0x092 + access_mode RW + modes M_CFG +} + +/* + * Data Channel Receive Message 3 + */ +register DCHRXMSG3 { + address 0x093 + access_mode RO + modes M_DFF0, M_DFF1 + field MCLASS 0x0F +} + +/* + * CMC Recieve Message 3 + */ +register CMCRXMSG3 { + address 0x093 + access_mode RO + modes M_CCHAN + field MCLASS 0x0F +} + +/* + * Overlay Recieve Message 3 + */ +register OVLYRXMSG3 { + address 0x093 + access_mode RO + modes M_SCSI + field MCLASS 0x0F +} + +/* + * PCI-X Control + */ +register PCIXCTL { + address 0x093 + access_mode RW + modes M_CFG + field SERRPULSE 0x80 + field UNEXPSCIEN 0x20 + field SPLTSMADIS 0x10 + field SPLTSTADIS 0x08 + field SRSPDPEEN 0x04 + field TSCSERREN 0x02 + field CMPABCDIS 0x01 +} + +/* + * CMC Sequencer Byte Count + */ +register CMCSEQBCNT { + address 0x094 + access_mode RO + modes M_CCHAN +} + +/* + * Overlay Sequencer Byte Count + */ +register OVLYSEQBCNT { + address 0x094 + access_mode RO + modes M_SCSI +} + +/* + * Data Channel Sequencer Byte Count + */ +register DCHSEQBCNT { + address 0x094 + access_mode RO + size 2 + modes M_DFF0, M_DFF1 +} + +/* + * Data Channel Split Status 0 + */ +register DCHSPLTSTAT0 { + address 0x096 + access_mode RW + modes M_DFF0, M_DFF1 + field STAETERM 0x80 + field SCBCERR 0x40 + field SCADERR 0x20 + field SCDATBUCKET 0x10 + field CNTNOTCMPLT 0x08 + field RXOVRUN 0x04 + field RXSCEMSG 0x02 + field RXSPLTRSP 0x01 +} + +/* + * CMC Split Status 0 + */ +register CMCSPLTSTAT0 { + address 0x096 + access_mode RW + modes M_CCHAN + field STAETERM 0x80 + field SCBCERR 0x40 + field SCADERR 0x20 + field SCDATBUCKET 0x10 + field CNTNOTCMPLT 0x08 + field RXOVRUN 0x04 + field RXSCEMSG 0x02 + field RXSPLTRSP 0x01 +} + +/* + * Overlay Split Status 0 + */ +register OVLYSPLTSTAT0 { + address 0x096 + access_mode RW + modes M_SCSI + field STAETERM 0x80 + field SCBCERR 0x40 + field SCADERR 0x20 + field SCDATBUCKET 0x10 + field CNTNOTCMPLT 0x08 + field RXOVRUN 0x04 + field RXSCEMSG 0x02 + field RXSPLTRSP 0x01 +} + +/* + * Data Channel Split Status 1 + */ +register DCHSPLTSTAT1 { + address 0x097 + access_mode RW + modes M_DFF0, M_DFF1 + field RXDATABUCKET 0x01 +} + +/* + * CMC Split Status 1 + */ +register CMCSPLTSTAT1 { + address 0x097 + access_mode RW + modes M_CCHAN + field RXDATABUCKET 0x01 +} + +/* + * Overlay Split Status 1 + */ +register OVLYSPLTSTAT1 { + address 0x097 + access_mode RW + modes M_SCSI + field RXDATABUCKET 0x01 +} + +/* + * S/G Receive Message 0 + */ +register SGRXMSG0 { + address 0x098 + access_mode RO + modes M_DFF0, M_DFF1 + field CDNUM 0xF8 + field CFNUM 0x07 +} + +/* + * S/G Receive Message 1 + */ +register SGRXMSG1 { + address 0x099 + access_mode RO + modes M_DFF0, M_DFF1 + field CBNUM 0xFF +} + +/* + * S/G Receive Message 2 + */ +register SGRXMSG2 { + address 0x09A + access_mode RO + modes M_DFF0, M_DFF1 + field MINDEX 0xFF +} + +/* + * S/G Receive Message 3 + */ +register SGRXMSG3 { + address 0x09B + access_mode RO + modes M_DFF0, M_DFF1 + field MCLASS 0x0F +} + +/* + * Slave Split Out Address 0 + */ +register SLVSPLTOUTADR0 { + address 0x098 + access_mode RO + modes M_SCSI + field LOWER_ADDR 0x7F +} + +/* + * Slave Split Out Address 1 + */ +register SLVSPLTOUTADR1 { + address 0x099 + access_mode RO + modes M_SCSI + field REQ_DNUM 0xF8 + field REQ_FNUM 0x07 +} + +/* + * Slave Split Out Address 2 + */ +register SLVSPLTOUTADR2 { + address 0x09A + access_mode RO + modes M_SCSI + field REQ_BNUM 0xFF +} + +/* + * Slave Split Out Address 3 + */ +register SLVSPLTOUTADR3 { + address 0x09B + access_mode RO + modes M_SCSI + field RLXORD 020 + field TAG_NUM 0x1F +} + +/* + * SG Sequencer Byte Count + */ +register SGSEQBCNT { + address 0x09C + access_mode RO + modes M_DFF0, M_DFF1 +} + +/* + * Slave Split Out Attribute 0 + */ +register SLVSPLTOUTATTR0 { + address 0x09C + access_mode RO + modes M_SCSI + field LOWER_BCNT 0xFF +} + +/* + * Slave Split Out Attribute 1 + */ +register SLVSPLTOUTATTR1 { + address 0x09D + access_mode RO + modes M_SCSI + field CMPLT_DNUM 0xF8 + field CMPLT_FNUM 0x07 +} + +/* + * Slave Split Out Attribute 2 + */ +register SLVSPLTOUTATTR2 { + address 0x09E + access_mode RO + size 2 + modes M_SCSI + field CMPLT_BNUM 0xFF +} +/* + * S/G Split Status 0 + */ +register SGSPLTSTAT0 { + address 0x09E + access_mode RW + modes M_DFF0, M_DFF1 + field STAETERM 0x80 + field SCBCERR 0x40 + field SCADERR 0x20 + field SCDATBUCKET 0x10 + field CNTNOTCMPLT 0x08 + field RXOVRUN 0x04 + field RXSCEMSG 0x02 + field RXSPLTRSP 0x01 +} + +/* + * S/G Split Status 1 + */ +register SGSPLTSTAT1 { + address 0x09F + access_mode RW + modes M_DFF0, M_DFF1 + field RXDATABUCKET 0x01 +} + +/* + * Special Function + */ +register SFUNCT { + address 0x09f + access_mode RW + modes M_CFG + field TEST_GROUP 0xF0 + field TEST_NUM 0x0F +} + +/* + * Data FIFO 0 PCI Status + */ +register DF0PCISTAT { + address 0x0A0 + access_mode RW + modes M_CFG + field DPE 0x80 + field SSE 0x40 + field RMA 0x20 + field RTA 0x10 + field SCAAPERR 0x08 + field RDPERR 0x04 + field TWATERR 0x02 + field DPR 0x01 +} + +/* + * Data FIFO 1 PCI Status + */ +register DF1PCISTAT { + address 0x0A1 + access_mode RW + modes M_CFG + field DPE 0x80 + field SSE 0x40 + field RMA 0x20 + field RTA 0x10 + field SCAAPERR 0x08 + field RDPERR 0x04 + field TWATERR 0x02 + field DPR 0x01 +} + +/* + * S/G PCI Status + */ +register SGPCISTAT { + address 0x0A2 + access_mode RW + modes M_CFG + field DPE 0x80 + field SSE 0x40 + field RMA 0x20 + field RTA 0x10 + field SCAAPERR 0x08 + field RDPERR 0x04 + field DPR 0x01 +} + +/* + * CMC PCI Status + */ +register CMCPCISTAT { + address 0x0A3 + access_mode RW + modes M_CFG + field DPE 0x80 + field SSE 0x40 + field RMA 0x20 + field RTA 0x10 + field SCAAPERR 0x08 + field RDPERR 0x04 + field TWATERR 0x02 + field DPR 0x01 +} + +/* + * Overlay PCI Status + */ +register OVLYPCISTAT { + address 0x0A4 + access_mode RW + modes M_CFG + field DPE 0x80 + field SSE 0x40 + field RMA 0x20 + field RTA 0x10 + field SCAAPERR 0x08 + field RDPERR 0x04 + field DPR 0x01 +} + +/* + * PCI Status for MSI Master DMA Transfer + */ +register MSIPCISTAT { + address 0x0A6 + access_mode RW + modes M_CFG + field SSE 0x40 + field RMA 0x20 + field RTA 0x10 + field CLRPENDMSI 0x08 + field TWATERR 0x02 + field DPR 0x01 +} + +/* + * PCI Status for Target + */ +register TARGPCISTAT { + address 0x0A7 + access_mode RW + modes M_CFG + field DPE 0x80 + field SSE 0x40 + field STA 0x08 + field TWATERR 0x02 +} + +/* + * LQ Packet In + * The last LQ Packet received + */ +register LQIN { + address 0x020 + access_mode RW + size 20 + modes M_DFF0, M_DFF1, M_SCSI +} + +/* + * SCB Type Pointer + * SCB offset for Target Mode SCB type information + */ +register TYPEPTR { + address 0x020 + access_mode RW + modes M_CFG +} + +/* + * Queue Tag Pointer + * SCB offset to the Two Byte tag identifier used for target mode. + */ +register TAGPTR { + address 0x021 + access_mode RW + modes M_CFG +} + +/* + * Logical Unit Number Pointer + * SCB offset to the LSB (little endian) of the lun field. + */ +register LUNPTR { + address 0x022 + access_mode RW + modes M_CFG +} + +/* + * Data Length Pointer + * SCB offset for the 4 byte data length field in target mode. + */ +register DATALENPTR { + address 0x023 + access_mode RW + modes M_CFG +} + +/* + * Status Length Pointer + * SCB offset to the two byte status field in target SCBs. + */ +register STATLENPTR { + address 0x024 + access_mode RW + modes M_CFG +} + +/* + * Command Length Pointer + * Scb offset for the CDB length field in initiator SCBs. + */ +register CMDLENPTR { + address 0x025 + access_mode RW + modes M_CFG +} + +/* + * Task Attribute Pointer + * Scb offset for the byte field specifying the attribute byte + * to be used in command packets. + */ +register ATTRPTR { + address 0x026 + access_mode RW + modes M_CFG +} + +/* + * Task Management Flags Pointer + * Scb offset for the byte field specifying the attribute flags + * byte to be used in command packets. + */ +register FLAGPTR { + address 0x027 + access_mode RW + modes M_CFG +} + +/* + * Command Pointer + * Scb offset for the first byte in the CDB for initiator SCBs. + */ +register CMDPTR { + address 0x028 + access_mode RW + modes M_CFG +} + +/* + * Queue Next Pointer + * Scb offset for the 2 byte "next scb link". + */ +register QNEXTPTR { + address 0x029 + access_mode RW + modes M_CFG +} + +/* + * SCSI ID Pointer + * Scb offset to the value to place in the SCSIID register + * during target mode connections. + */ +register IDPTR { + address 0x02A + access_mode RW + modes M_CFG +} + +/* + * Command Aborted Byte Pointer + * Offset to the SCB flags field that includes the + * "SCB aborted" status bit. + */ +register ABRTBYTEPTR { + address 0x02B + access_mode RW + modes M_CFG +} + +/* + * Command Aborted Bit Pointer + * Bit offset in the SCB flags field for "SCB aborted" status. + */ +register ABRTBITPTR { + address 0x02C + access_mode RW + modes M_CFG +} + +/* + * Rev B or greater. + */ +register MAXCMDBYTES { + address 0x02D + access_mode RW + modes M_CFG +} + +/* + * Rev B or greater. + */ +register MAXCMD2RCV { + address 0x02E + access_mode RW + modes M_CFG +} + +/* + * Rev B or greater. + */ +register SHORTTHRESH { + address 0x02F + access_mode RW + modes M_CFG +} + +/* + * Logical Unit Number Length + * The length, in bytes, of the SCB lun field. + */ +register LUNLEN { + address 0x030 + access_mode RW + modes M_CFG + mask ILUNLEN 0x0F + mask TLUNLEN 0xF0 +} +const LUNLEN_SINGLE_LEVEL_LUN 0xF + +/* + * CDB Limit + * The size, in bytes, of the embedded CDB field in initator SCBs. + */ +register CDBLIMIT { + address 0x031 + access_mode RW + modes M_CFG +} + +/* + * Maximum Commands + * The maximum number of commands to issue during a + * single packetized connection. + */ +register MAXCMD { + address 0x032 + access_mode RW + modes M_CFG +} + +/* + * Maximum Command Counter + * The number of commands already sent during this connection + */ +register MAXCMDCNT { + address 0x033 + access_mode RW + modes M_CFG +} + +/* + * LQ Packet Reserved Bytes + * The bytes to be sent in the currently reserved fileds + * of all LQ packets. + */ +register LQRSVD01 { + address 0x034 + access_mode RW + modes M_SCSI +} +register LQRSVD16 { + address 0x035 + access_mode RW + modes M_SCSI +} +register LQRSVD17 { + address 0x036 + access_mode RW + modes M_SCSI +} + +/* + * Command Reserved 0 + * The byte to be sent for the reserved byte 0 of + * outgoing command packets. + */ +register CMDRSVD0 { + address 0x037 + access_mode RW + modes M_CFG +} + +/* + * LQ Manager Control 0 + */ +register LQCTL0 { + address 0x038 + access_mode RW + modes M_CFG + field LQITARGCLT 0xC0 + field LQIINITGCLT 0x30 + field LQ0TARGCLT 0x0C + field LQ0INITGCLT 0x03 +} + +/* + * LQ Manager Control 1 + */ +register LQCTL1 { + address 0x038 + access_mode RW + modes M_DFF0, M_DFF1, M_SCSI + field PCI2PCI 0x04 + field SINGLECMD 0x02 + field ABORTPENDING 0x01 +} + +/* + * LQ Manager Control 2 + */ +register LQCTL2 { + address 0x039 + access_mode RW + modes M_DFF0, M_DFF1, M_SCSI + field LQIRETRY 0x80 + field LQICONTINUE 0x40 + field LQITOIDLE 0x20 + field LQIPAUSE 0x10 + field LQORETRY 0x08 + field LQOCONTINUE 0x04 + field LQOTOIDLE 0x02 + field LQOPAUSE 0x01 +} + +/* + * SCSI RAM BIST0 + */ +register SCSBIST0 { + address 0x039 + access_mode RW + modes M_CFG + field GSBISTERR 0x40 + field GSBISTDONE 0x20 + field GSBISTRUN 0x10 + field OSBISTERR 0x04 + field OSBISTDONE 0x02 + field OSBISTRUN 0x01 +} + +/* + * SCSI Sequence Control0 + */ +register SCSISEQ0 { + address 0x03A + access_mode RW + modes M_DFF0, M_DFF1, M_SCSI + field TEMODEO 0x80 + field ENSELO 0x40 + field ENARBO 0x20 + field FORCEBUSFREE 0x10 + field SCSIRSTO 0x01 +} + +/* + * SCSI RAM BIST 1 + */ +register SCSBIST1 { + address 0x03A + access_mode RW + modes M_CFG + field NTBISTERR 0x04 + field NTBISTDONE 0x02 + field NTBISTRUN 0x01 +} + +/* + * SCSI Sequence Control 1 + */ +register SCSISEQ1 { + address 0x03B + access_mode RW + modes M_DFF0, M_DFF1, M_SCSI + field MANUALCTL 0x40 + field ENSELI 0x20 + field ENRSELI 0x10 + field MANUALP 0x0C + field ENAUTOATNP 0x02 + field ALTSTIM 0x01 +} + +/* + * SCSI Transfer Control 0 + */ +register SXFRCTL0 { + address 0x03C + access_mode RW + modes M_SCSI + field DFON 0x80 + field DFPEXP 0x40 + field BIOSCANCELEN 0x10 + field SPIOEN 0x08 +} + +/* + * SCSI Transfer Control 1 + */ +register SXFRCTL1 { + address 0x03D + access_mode RW + modes M_SCSI + field BITBUCKET 0x80 + field ENSACHK 0x40 + field ENSPCHK 0x20 + field STIMESEL 0x18 + field ENSTIMER 0x04 + field ACTNEGEN 0x02 + field STPWEN 0x01 +} + +/* + * SCSI Transfer Control 2 + */ +register SXFRCTL2 { + address 0x03E + access_mode RW + modes M_SCSI + field AUTORSTDIS 0x10 + field CMDDMAEN 0x08 + field ASU 0x07 +} + +/* + * SCSI Bus Initiator IDs + * Bitmask of observed initiators on the bus. + */ +register BUSINITID { + address 0x03C + access_mode RW + modes M_CFG + size 2 +} + +/* + * Data Length Counters + * Packet byte counter. + */ +register DLCOUNT { + address 0x03C + access_mode RW + modes M_DFF0, M_DFF1 + size 3 +} + +/* + * Data FIFO Status + */ +register DFFSTAT { + address 0x03F + access_mode RW + modes M_SCSI + field FIFO1FREE 0x20 + field FIFO0FREE 0x10 + /* + * On the B, this enum only works + * in the read direction. For writes, + * you must use the B version of the + * CURRFIFO_0 definition which is defined + * as a constant outside of this register + * definition to avoid confusing the + * register pretty printing code. + */ + enum CURRFIFO 0x03 { + CURRFIFO_0, + CURRFIFO_1, + CURRFIFO_NONE 0x3 + } +} + +const B_CURRFIFO_0 0x2 + +/* + * SCSI Bus Target IDs + * Bitmask of observed targets on the bus. + */ +register BUSTARGID { + address 0x03E + access_mode RW + modes M_CFG + size 2 +} + +/* + * SCSI Control Signal Out + */ +register SCSISIGO { + address 0x040 + access_mode RW + modes M_DFF0, M_DFF1, M_SCSI + field CDO 0x80 + field IOO 0x40 + field MSGO 0x20 + field ATNO 0x10 + field SELO 0x08 + field BSYO 0x04 + field REQO 0x02 + field ACKO 0x01 +/* + * Possible phases to write into SCSISIG0 + */ + enum PHASE_MASK CDO|IOO|MSGO { + P_DATAOUT 0x0, + P_DATAIN IOO, + P_DATAOUT_DT P_DATAOUT|MSGO, + P_DATAIN_DT P_DATAIN|MSGO, + P_COMMAND CDO, + P_MESGOUT CDO|MSGO, + P_STATUS CDO|IOO, + P_MESGIN CDO|IOO|MSGO + } +} + +register SCSISIGI { + address 0x041 + access_mode RO + modes M_DFF0, M_DFF1, M_SCSI + field CDI 0x80 + field IOI 0x40 + field MSGI 0x20 + field ATNI 0x10 + field SELI 0x08 + field BSYI 0x04 + field REQI 0x02 + field ACKI 0x01 +/* + * Possible phases in SCSISIGI + */ + enum PHASE_MASK CDO|IOO|MSGO { + P_DATAOUT 0x0, + P_DATAIN IOO, + P_DATAOUT_DT P_DATAOUT|MSGO, + P_DATAIN_DT P_DATAIN|MSGO, + P_COMMAND CDO, + P_MESGOUT CDO|MSGO, + P_STATUS CDO|IOO, + P_MESGIN CDO|IOO|MSGO + } +} + +/* + * Multiple Target IDs + * Bitmask of ids to respond as a target. + */ +register MULTARGID { + address 0x040 + access_mode RW + modes M_CFG + size 2 +} + +/* + * SCSI Phase + */ +register SCSIPHASE { + address 0x042 + access_mode RO + modes M_DFF0, M_DFF1, M_SCSI + field STATUS_PHASE 0x20 + field COMMAND_PHASE 0x10 + field MSG_IN_PHASE 0x08 + field MSG_OUT_PHASE 0x04 + field DATA_PHASE_MASK 0x03 { + DATA_OUT_PHASE 0x01, + DATA_IN_PHASE 0x02 + } +} + +/* + * SCSI Data 0 Image + */ +register SCSIDAT0_IMG { + address 0x043 + access_mode RW + modes M_DFF0, M_DFF1, M_SCSI +} + +/* + * SCSI Latched Data + */ +register SCSIDAT { + address 0x044 + access_mode RW + modes M_DFF0, M_DFF1, M_SCSI + size 2 +} + +/* + * SCSI Data Bus + */ +register SCSIBUS { + address 0x046 + access_mode RW + modes M_DFF0, M_DFF1, M_SCSI + size 2 +} + +/* + * Target ID In + */ +register TARGIDIN { + address 0x048 + access_mode RO + modes M_DFF0, M_DFF1, M_SCSI + field CLKOUT 0x80 + field TARGID 0x0F +} + +/* + * Selection/Reselection ID + * Upper four bits are the device id. The ONEBIT is set when the re/selecting + * device did not set its own ID. + */ +register SELID { + address 0x049 + access_mode RW + modes M_DFF0, M_DFF1, M_SCSI + field SELID_MASK 0xf0 + field ONEBIT 0x08 +} + +/* + * SCSI Block Control + * Controls Bus type and channel selection. SELWIDE allows for the + * coexistence of 8bit and 16bit devices on a wide bus. + */ +register SBLKCTL { + address 0x04A + access_mode RW + modes M_DFF0, M_DFF1, M_SCSI + field DIAGLEDEN 0x80 + field DIAGLEDON 0x40 + field ENAB40 0x08 /* LVD transceiver active */ + field ENAB20 0x04 /* SE/HVD transceiver active */ + field SELWIDE 0x02 +} + +/* + * Option Mode + */ +register OPTIONMODE { + address 0x04A + access_mode RW + modes M_CFG + field BIOSCANCTL 0x80 + field AUTOACKEN 0x40 + field BIASCANCTL 0x20 + field BUSFREEREV 0x10 + field ENDGFORMCHK 0x04 + field AUTO_MSGOUT_DE 0x02 + mask OPTIONMODE_DEFAULTS AUTO_MSGOUT_DE +} + +/* + * SCSI Status 0 + */ +register SSTAT0 { + address 0x04B + access_mode RO + modes M_DFF0, M_DFF1, M_SCSI + field TARGET 0x80 /* Board acting as target */ + field SELDO 0x40 /* Selection Done */ + field SELDI 0x20 /* Board has been selected */ + field SELINGO 0x10 /* Selection In Progress */ + field IOERR 0x08 /* LVD Tranceiver mode changed */ + field OVERRUN 0x04 /* SCSI Offset overrun detected */ + field SPIORDY 0x02 /* SCSI PIO Ready */ + field ARBDO 0x01 /* Arbitration Done Out */ +} + +/* + * Clear SCSI Interrupt 0 + * Writing a 1 to a bit clears the associated SCSI Interrupt in SSTAT0. + */ +register CLRSINT0 { + address 0x04B + access_mode WO + modes M_DFF0, M_DFF1, M_SCSI + field CLRSELDO 0x40 + field CLRSELDI 0x20 + field CLRSELINGO 0x10 + field CLRIOERR 0x08 + field CLROVERRUN 0x04 + field CLRSPIORDY 0x02 + field CLRARBDO 0x01 +} + +/* + * SCSI Interrupt Mode 0 + * Setting any bit will enable the corresponding function + * in SIMODE0 to interrupt via the IRQ pin. + */ +register SIMODE0 { + address 0x04B + access_mode RW + modes M_CFG + field ENSELDO 0x40 + field ENSELDI 0x20 + field ENSELINGO 0x10 + field ENIOERR 0x08 + field ENOVERRUN 0x04 + field ENSPIORDY 0x02 + field ENARBDO 0x01 +} + +/* + * SCSI Status 1 + */ +register SSTAT1 { + address 0x04C + access_mode RO + modes M_DFF0, M_DFF1, M_SCSI + field SELTO 0x80 + field ATNTARG 0x40 + field SCSIRSTI 0x20 + field PHASEMIS 0x10 + field BUSFREE 0x08 + field SCSIPERR 0x04 + field STRB2FAST 0x02 + field REQINIT 0x01 +} + +/* + * Clear SCSI Interrupt 1 + * Writing a 1 to a bit clears the associated SCSI Interrupt in SSTAT1. + */ +register CLRSINT1 { + address 0x04C + access_mode WO + modes M_DFF0, M_DFF1, M_SCSI + field CLRSELTIMEO 0x80 + field CLRATNO 0x40 + field CLRSCSIRSTI 0x20 + field CLRBUSFREE 0x08 + field CLRSCSIPERR 0x04 + field CLRSTRB2FAST 0x02 + field CLRREQINIT 0x01 +} + +/* + * SCSI Status 2 + */ +register SSTAT2 { + address 0x04d + access_mode RO + modes M_DFF0, M_DFF1, M_SCSI + field BUSFREETIME 0xc0 { + BUSFREE_LQO 0x40, + BUSFREE_DFF0 0x80, + BUSFREE_DFF1 0xC0 + } + field NONPACKREQ 0x20 + field EXP_ACTIVE 0x10 /* SCSI Expander Active */ + field BSYX 0x08 /* Busy Expander */ + field WIDE_RES 0x04 /* Modes 0 and 1 only */ + field SDONE 0x02 /* Modes 0 and 1 only */ + field DMADONE 0x01 /* Modes 0 and 1 only */ +} + +/* + * Clear SCSI Interrupt 2 + */ +register CLRSINT2 { + address 0x04D + access_mode WO + modes M_DFF0, M_DFF1, M_SCSI + field CLRNONPACKREQ 0x20 + field CLRWIDE_RES 0x04 /* Modes 0 and 1 only */ + field CLRSDONE 0x02 /* Modes 0 and 1 only */ + field CLRDMADONE 0x01 /* Modes 0 and 1 only */ +} + +/* + * SCSI Interrupt Mode 2 + */ +register SIMODE2 { + address 0x04D + access_mode RW + modes M_CFG + field ENWIDE_RES 0x04 + field ENSDONE 0x02 + field ENDMADONE 0x01 +} + +/* + * Physical Error Diagnosis + */ +register PERRDIAG { + address 0x04E + access_mode RO + modes M_DFF0, M_DFF1, M_SCSI + field HIZERO 0x80 + field HIPERR 0x40 + field PREVPHASE 0x20 + field PARITYERR 0x10 + field AIPERR 0x08 + field CRCERR 0x04 + field DGFORMERR 0x02 + field DTERR 0x01 +} + +/* + * LQI Manager Current State + */ +register LQISTATE { + address 0x04E + access_mode RO + modes M_CFG +} + +/* + * SCSI Offset Count + */ +register SOFFCNT { + address 0x04F + access_mode RO + modes M_DFF0, M_DFF1, M_SCSI +} + +/* + * LQO Manager Current State + */ +register LQOSTATE { + address 0x04F + access_mode RO + modes M_CFG +} + +/* + * LQI Manager Status + */ +register LQISTAT0 { + address 0x050 + access_mode RO + modes M_DFF0, M_DFF1, M_SCSI + field LQIATNQAS 0x20 + field LQICRCT1 0x10 + field LQICRCT2 0x08 + field LQIBADLQT 0x04 + field LQIATNLQ 0x02 + field LQIATNCMD 0x01 +} + +/* + * Clear LQI Interrupts 0 + */ +register CLRLQIINT0 { + address 0x050 + access_mode WO + modes M_DFF0, M_DFF1, M_SCSI + field CLRLQIATNQAS 0x20 + field CLRLQICRCT1 0x10 + field CLRLQICRCT2 0x08 + field CLRLQIBADLQT 0x04 + field CLRLQIATNLQ 0x02 + field CLRLQIATNCMD 0x01 +} + +/* + * LQI Manager Interrupt Mode 0 + */ +register LQIMODE0 { + address 0x050 + access_mode RW + modes M_CFG + field ENLQIATNQASK 0x20 + field ENLQICRCT1 0x10 + field ENLQICRCT2 0x08 + field ENLQIBADLQT 0x04 + field ENLQIATNLQ 0x02 + field ENLQIATNCMD 0x01 +} + +/* + * LQI Manager Status 1 + */ +register LQISTAT1 { + address 0x051 + access_mode RO + modes M_DFF0, M_DFF1, M_SCSI + field LQIPHASE_LQ 0x80 + field LQIPHASE_NLQ 0x40 + field LQIABORT 0x20 + field LQICRCI_LQ 0x10 + field LQICRCI_NLQ 0x08 + field LQIBADLQI 0x04 + field LQIOVERI_LQ 0x02 + field LQIOVERI_NLQ 0x01 +} + +/* + * Clear LQI Manager Interrupts1 + */ +register CLRLQIINT1 { + address 0x051 + access_mode WO + modes M_DFF0, M_DFF1, M_SCSI + field CLRLQIPHASE_LQ 0x80 + field CLRLQIPHASE_NLQ 0x40 + field CLRLIQABORT 0x20 + field CLRLQICRCI_LQ 0x10 + field CLRLQICRCI_NLQ 0x08 + field CLRLQIBADLQI 0x04 + field CLRLQIOVERI_LQ 0x02 + field CLRLQIOVERI_NLQ 0x01 +} + +/* + * LQI Manager Interrupt Mode 1 + */ +register LQIMODE1 { + address 0x051 + access_mode RW + modes M_CFG + field ENLQIPHASE_LQ 0x80 /* LQIPHASE1 */ + field ENLQIPHASE_NLQ 0x40 /* LQIPHASE2 */ + field ENLIQABORT 0x20 + field ENLQICRCI_LQ 0x10 /* LQICRCI1 */ + field ENLQICRCI_NLQ 0x08 /* LQICRCI2 */ + field ENLQIBADLQI 0x04 + field ENLQIOVERI_LQ 0x02 /* LQIOVERI1 */ + field ENLQIOVERI_NLQ 0x01 /* LQIOVERI2 */ +} + +/* + * LQI Manager Status 2 + */ +register LQISTAT2 { + address 0x052 + access_mode RO + modes M_DFF0, M_DFF1, M_SCSI + field PACKETIZED 0x80 + field LQIPHASE_OUTPKT 0x40 + field LQIWORKONLQ 0x20 + field LQIWAITFIFO 0x10 + field LQISTOPPKT 0x08 + field LQISTOPLQ 0x04 + field LQISTOPCMD 0x02 + field LQIGSAVAIL 0x01 +} + +/* + * SCSI Status 3 + */ +register SSTAT3 { + address 0x053 + access_mode RO + modes M_DFF0, M_DFF1, M_SCSI + field NTRAMPERR 0x02 + field OSRAMPERR 0x01 +} + +/* + * Clear SCSI Status 3 + */ +register CLRSINT3 { + address 0x053 + access_mode WO + modes M_DFF0, M_DFF1, M_SCSI + field CLRNTRAMPERR 0x02 + field CLROSRAMPERR 0x01 +} + +/* + * SCSI Interrupt Mode 3 + */ +register SIMODE3 { + address 0x053 + access_mode RW + modes M_CFG + field ENNTRAMPERR 0x02 + field ENOSRAMPERR 0x01 +} + +/* + * LQO Manager Status 0 + */ +register LQOSTAT0 { + address 0x054 + access_mode RO + modes M_DFF0, M_DFF1, M_SCSI + field LQOTARGSCBPERR 0x10 + field LQOSTOPT2 0x08 + field LQOATNLQ 0x04 + field LQOATNPKT 0x02 + field LQOTCRC 0x01 +} + +/* + * Clear LQO Manager interrupt 0 + */ +register CLRLQOINT0 { + address 0x054 + access_mode WO + modes M_DFF0, M_DFF1, M_SCSI + field CLRLQOTARGSCBPERR 0x10 + field CLRLQOSTOPT2 0x08 + field CLRLQOATNLQ 0x04 + field CLRLQOATNPKT 0x02 + field CLRLQOTCRC 0x01 +} + +/* + * LQO Manager Interrupt Mode 0 + */ +register LQOMODE0 { + address 0x054 + access_mode RW + modes M_CFG + field ENLQOTARGSCBPERR 0x10 + field ENLQOSTOPT2 0x08 + field ENLQOATNLQ 0x04 + field ENLQOATNPKT 0x02 + field ENLQOTCRC 0x01 +} + +/* + * LQO Manager Status 1 + */ +register LQOSTAT1 { + address 0x055 + access_mode RO + modes M_DFF0, M_DFF1, M_SCSI + field LQOINITSCBPERR 0x10 + field LQOSTOPI2 0x08 + field LQOBADQAS 0x04 + field LQOBUSFREE 0x02 + field LQOPHACHGINPKT 0x01 +} + +/* + * Clear LOQ Interrupt 1 + */ +register CLRLQOINT1 { + address 0x055 + access_mode WO + modes M_DFF0, M_DFF1, M_SCSI + field CLRLQOINITSCBPERR 0x10 + field CLRLQOSTOPI2 0x08 + field CLRLQOBADQAS 0x04 + field CLRLQOBUSFREE 0x02 + field CLRLQOPHACHGINPKT 0x01 +} + +/* + * LQO Manager Interrupt Mode 1 + */ +register LQOMODE1 { + address 0x055 + access_mode RW + modes M_CFG + field ENLQOINITSCBPERR 0x10 + field ENLQOSTOPI2 0x08 + field ENLQOBADQAS 0x04 + field ENLQOBUSFREE 0x02 + field ENLQOPHACHGINPKT 0x01 +} + +/* + * LQO Manager Status 2 + */ +register LQOSTAT2 { + address 0x056 + access_mode RO + modes M_DFF0, M_DFF1, M_SCSI + field LQOPKT 0xE0 + field LQOWAITFIFO 0x10 + field LQOPHACHGOUTPKT 0x02 /* outside of packet boundaries. */ + field LQOSTOP0 0x01 /* Stopped after sending all packets */ +} + +/* + * Output Synchronizer Space Count + */ +register OS_SPACE_CNT { + address 0x056 + access_mode RO + modes M_CFG +} + +/* + * SCSI Interrupt Mode 1 + * Setting any bit will enable the corresponding function + * in SIMODE1 to interrupt via the IRQ pin. + */ +register SIMODE1 { + address 0x057 + access_mode RW + modes M_DFF0, M_DFF1, M_SCSI + field ENSELTIMO 0x80 + field ENATNTARG 0x40 + field ENSCSIRST 0x20 + field ENPHASEMIS 0x10 + field ENBUSFREE 0x08 + field ENSCSIPERR 0x04 + field ENSTRB2FAST 0x02 + field ENREQINIT 0x01 +} + +/* + * Good Status FIFO + */ +register GSFIFO { + address 0x058 + access_mode RO + size 2 + modes M_DFF0, M_DFF1, M_SCSI +} + +/* + * Data FIFO SCSI Transfer Control + */ +register DFFSXFRCTL { + address 0x05A + access_mode RW + modes M_DFF0, M_DFF1 + field DFFBITBUCKET 0x08 + field CLRSHCNT 0x04 + field CLRCHN 0x02 + field RSTCHN 0x01 +} + +/* + * Next SCSI Control Block + */ +register NEXTSCB { + address 0x05A + access_mode RW + size 2 + modes M_SCSI +} + +/* Rev B only. */ +register LQOSCSCTL { + address 0x05A + access_mode RW + size 1 + modes M_CFG + field LQOH2A_VERSION 0x80 + field LQONOCHKOVER 0x01 +} + +/* + * SEQ Interrupts + */ +register SEQINTSRC { + address 0x05B + access_mode RO + modes M_DFF0, M_DFF1 + field CTXTDONE 0x40 + field SAVEPTRS 0x20 + field CFG4DATA 0x10 + field CFG4ISTAT 0x08 + field CFG4TSTAT 0x04 + field CFG4ICMD 0x02 + field CFG4TCMD 0x01 +} + +/* + * Clear Arp Interrupts + */ +register CLRSEQINTSRC { + address 0x05B + access_mode WO + modes M_DFF0, M_DFF1 + field CLRCTXTDONE 0x40 + field CLRSAVEPTRS 0x20 + field CLRCFG4DATA 0x10 + field CLRCFG4ISTAT 0x08 + field CLRCFG4TSTAT 0x04 + field CLRCFG4ICMD 0x02 + field CLRCFG4TCMD 0x01 +} + +/* + * SEQ Interrupt Enabled (Shared) + */ +register SEQIMODE { + address 0x05C + access_mode RW + modes M_DFF0, M_DFF1 + field ENCTXTDONE 0x40 + field ENSAVEPTRS 0x20 + field ENCFG4DATA 0x10 + field ENCFG4ISTAT 0x08 + field ENCFG4TSTAT 0x04 + field ENCFG4ICMD 0x02 + field ENCFG4TCMD 0x01 +} + +/* + * Current SCSI Control Block + */ +register CURRSCB { + address 0x05C + access_mode RW + size 2 + modes M_SCSI +} + +/* + * Data FIFO Status + */ +register MDFFSTAT { + address 0x05D + access_mode RO + modes M_DFF0, M_DFF1 + field SHCNTNEGATIVE 0x40 /* Rev B or higher */ + field SHCNTMINUS1 0x20 /* Rev B or higher */ + field LASTSDONE 0x10 + field SHVALID 0x08 + field DLZERO 0x04 /* FIFO data ends on packet boundary. */ + field DATAINFIFO 0x02 + field FIFOFREE 0x01 +} + +/* + * CRC Control + */ +register CRCCONTROL { + address 0x05d + access_mode RW + modes M_CFG + field CRCVALCHKEN 0x40 +} + +/* + * SCSI Test Control + */ +register SCSITEST { + address 0x05E + access_mode RW + modes M_CFG + field CNTRTEST 0x08 + field SEL_TXPLL_DEBUG 0x04 +} + +/* + * Data FIFO Queue Tag + */ +register DFFTAG { + address 0x05E + access_mode RW + size 2 + modes M_DFF0, M_DFF1 +} + +/* + * Last SCSI Control Block + */ +register LASTSCB { + address 0x05E + access_mode RW + size 2 + modes M_SCSI +} + +/* + * SCSI I/O Cell Power-down Control + */ +register IOPDNCTL { + address 0x05F + access_mode RW + modes M_CFG + field DISABLE_OE 0x80 + field PDN_IDIST 0x04 + field PDN_DIFFSENSE 0x01 +} + +/* + * Shaddow Host Address. + */ +register SHADDR { + address 0x060 + access_mode RO + size 8 + modes M_DFF0, M_DFF1 +} + +/* + * Data Group CRC Interval. + */ +register DGRPCRCI { + address 0x060 + access_mode RW + size 2 + modes M_CFG +} + +/* + * Data Transfer Negotiation Address + */ +register NEGOADDR { + address 0x060 + access_mode RW + modes M_SCSI +} + +/* + * Data Transfer Negotiation Data - Period Byte + */ +register NEGPERIOD { + address 0x061 + access_mode RW + modes M_SCSI +} + +/* + * Packetized CRC Interval + */ +register PACKCRCI { + address 0x062 + access_mode RW + size 2 + modes M_CFG +} + +/* + * Data Transfer Negotiation Data - Offset Byte + */ +register NEGOFFSET { + address 0x062 + access_mode RW + modes M_SCSI +} + +/* + * Data Transfer Negotiation Data - PPR Options + */ +register NEGPPROPTS { + address 0x063 + access_mode RW + modes M_SCSI + field PPROPT_PACE 0x08 + field PPROPT_QAS 0x04 + field PPROPT_DT 0x02 + field PPROPT_IUT 0x01 +} + +/* + * Data Transfer Negotiation Data - Connection Options + */ +register NEGCONOPTS { + address 0x064 + access_mode RW + modes M_SCSI + field ENSNAPSHOT 0x40 + field RTI_WRTDIS 0x20 + field RTI_OVRDTRN 0x10 + field ENSLOWCRC 0x08 + field ENAUTOATNI 0x04 + field ENAUTOATNO 0x02 + field WIDEXFER 0x01 +} + +/* + * Negotiation Table Annex Column Index. + */ +register ANNEXCOL { + address 0x065 + access_mode RW + modes M_SCSI +} + +register SCSCHKN { + address 0x066 + access_mode RW + modes M_CFG + field STSELSKIDDIS 0x40 + field CURRFIFODEF 0x20 + field WIDERESEN 0x10 + field SDONEMSKDIS 0x08 + field DFFACTCLR 0x04 + field SHVALIDSTDIS 0x02 + field LSTSGCLRDIS 0x01 +} + +const AHD_ANNEXCOL_PER_DEV0 4 +const AHD_NUM_PER_DEV_ANNEXCOLS 4 +const AHD_ANNEXCOL_PRECOMP_SLEW 4 +const AHD_PRECOMP_MASK 0x07 +const AHD_PRECOMP_SHIFT 0 +const AHD_PRECOMP_CUTBACK_17 0x04 +const AHD_PRECOMP_CUTBACK_29 0x06 +const AHD_PRECOMP_CUTBACK_37 0x07 +const AHD_SLEWRATE_MASK 0x78 +const AHD_SLEWRATE_SHIFT 3 +/* + * Rev A has only a single bit (high bit of field) of slew adjustment. + * Rev B has 4 bits. The current default happens to be the same for both. + */ +const AHD_SLEWRATE_DEF_REVA 0x08 +const AHD_SLEWRATE_DEF_REVB 0x08 + +/* Rev A does not have any amplitude setting. */ +const AHD_ANNEXCOL_AMPLITUDE 6 +const AHD_AMPLITUDE_MASK 0x7 +const AHD_AMPLITUDE_SHIFT 0 +const AHD_AMPLITUDE_DEF 0x7 + +/* + * Negotiation Table Annex Data Port. + */ +register ANNEXDAT { + address 0x066 + access_mode RW + modes M_SCSI +} + +/* + * Initiator's Own Id. + * The SCSI ID to use for Selection Out and seen during a reselection.. + */ +register IOWNID { + address 0x067 + access_mode RW + modes M_SCSI +} + +/* + * 960MHz Phase-Locked Loop Control 0 + */ +register PLL960CTL0 { + address 0x068 + access_mode RW + modes M_CFG + field PLL_VCOSEL 0x80 + field PLL_PWDN 0x40 + field PLL_NS 0x30 + field PLL_ENLUD 0x08 + field PLL_ENLPF 0x04 + field PLL_DLPF 0x02 + field PLL_ENFBM 0x01 +} + +/* + * Target Own Id + */ +register TOWNID { + address 0x069 + access_mode RW + modes M_SCSI +} + +/* + * 960MHz Phase-Locked Loop Control 1 + */ +register PLL960CTL1 { + address 0x069 + access_mode RW + modes M_CFG + field PLL_CNTEN 0x80 + field PLL_CNTCLR 0x40 + field PLL_RST 0x01 +} + +/* + * Expander Signature + */ +register XSIG { + address 0x06A + access_mode RW + modes M_SCSI +} + +/* + * Shadow Byte Count + */ +register SHCNT { + address 0x068 + access_mode RW + size 3 + modes M_DFF0, M_DFF1 +} + +/* + * Selection Out ID + */ +register SELOID { + address 0x06B + access_mode RW + modes M_SCSI +} + +/* + * 960-MHz Phase-Locked Loop Test Count + */ +register PLL960CNT0 { + address 0x06A + access_mode RO + size 2 + modes M_CFG +} + +/* + * 400-MHz Phase-Locked Loop Control 0 + */ +register PLL400CTL0 { + address 0x06C + access_mode RW + modes M_CFG + field PLL_VCOSEL 0x80 + field PLL_PWDN 0x40 + field PLL_NS 0x30 + field PLL_ENLUD 0x08 + field PLL_ENLPF 0x04 + field PLL_DLPF 0x02 + field PLL_ENFBM 0x01 +} + +/* + * Arbitration Fairness + */ +register FAIRNESS { + address 0x06C + access_mode RW + size 2 + modes M_SCSI +} + +/* + * 400-MHz Phase-Locked Loop Control 1 + */ +register PLL400CTL1 { + address 0x06D + access_mode RW + modes M_CFG + field PLL_CNTEN 0x80 + field PLL_CNTCLR 0x40 + field PLL_RST 0x01 +} + +/* + * Arbitration Unfairness + */ +register UNFAIRNESS { + address 0x06E + access_mode RW + size 2 + modes M_SCSI +} + +/* + * 400-MHz Phase-Locked Loop Test Count + */ +register PLL400CNT0 { + address 0x06E + access_mode RO + size 2 + modes M_CFG +} + +/* + * SCB Page Pointer + */ +register SCBPTR { + address 0x0A8 + access_mode RW + size 2 + modes M_DFF0, M_DFF1, M_CCHAN, M_SCSI +} + +/* + * CMC SCB Array Count + * Number of bytes to transfer between CMC SCB memory and SCBRAM. + * Transfers must be 8byte aligned and sized. + */ +register CCSCBACNT { + address 0x0AB + access_mode RW + modes M_CCHAN +} + +/* + * SCB Autopointer + * SCB-Next Address Snooping logic. When an SCB is transferred to + * the card, the next SCB address to be used by the CMC array can + * be autoloaded from that transfer. + */ +register SCBAUTOPTR { + address 0x0AB + access_mode RW + modes M_CFG + field AUSCBPTR_EN 0x80 + field SCBPTR_ADDR 0x38 + field SCBPTR_OFF 0x07 +} + +/* + * CMC SG Ram Address Pointer + */ +register CCSGADDR { + address 0x0AC + access_mode RW + modes M_DFF0, M_DFF1 +} + +/* + * CMC SCB RAM Address Pointer + */ +register CCSCBADDR { + address 0x0AC + access_mode RW + modes M_CCHAN +} + +/* + * CMC SCB Ram Back-up Address Pointer + * Indicates the true stop location of transfers halted prior + * to SCBHCNT going to 0. + */ +register CCSCBADR_BK { + address 0x0AC + access_mode RO + modes M_CFG +} + +/* + * CMC SG Control + */ +register CCSGCTL { + address 0x0AD + access_mode RW + modes M_DFF0, M_DFF1 + field CCSGDONE 0x80 + field SG_CACHE_AVAIL 0x10 + field CCSGENACK 0x08 + mask CCSGEN 0x0C + field SG_FETCH_REQ 0x02 + field CCSGRESET 0x01 +} + +/* + * CMD SCB Control + */ +register CCSCBCTL { + address 0x0AD + access_mode RW + modes M_CCHAN + field CCSCBDONE 0x80 + field ARRDONE 0x40 + field CCARREN 0x10 + field CCSCBEN 0x08 + field CCSCBDIR 0x04 + field CCSCBRESET 0x01 +} + +/* + * CMC Ram BIST + */ +register CMC_RAMBIST { + address 0x0AD + access_mode RW + modes M_CFG + field SG_ELEMENT_SIZE 0x80 + field SCBRAMBIST_FAIL 0x40 + field SG_BIST_FAIL 0x20 + field SG_BIST_EN 0x10 + field CMC_BUFFER_BIST_FAIL 0x02 + field CMC_BUFFER_BIST_EN 0x01 +} + +/* + * CMC SG RAM Data Port + */ +register CCSGRAM { + address 0x0B0 + access_mode RW + modes M_DFF0, M_DFF1 +} + +/* + * CMC SCB RAM Data Port + */ +register CCSCBRAM { + address 0x0B0 + access_mode RW + modes M_CCHAN +} + +/* + * Flex DMA Address. + */ +register FLEXADR { + address 0x0B0 + access_mode RW + size 3 + modes M_SCSI +} + +/* + * Flex DMA Byte Count + */ +register FLEXCNT { + address 0x0B3 + access_mode RW + size 2 + modes M_SCSI +} + +/* + * Flex DMA Status + */ +register FLEXDMASTAT { + address 0x0B5 + access_mode RW + modes M_SCSI + field FLEXDMAERR 0x02 + field FLEXDMADONE 0x01 +} + +/* + * Flex DMA Data Port + */ +register FLEXDATA { + address 0x0B6 + access_mode RW + modes M_SCSI +} + +/* + * Board Data + */ +register BRDDAT { + address 0x0B8 + access_mode RW + modes M_SCSI +} + +/* + * Board Control + */ +register BRDCTL { + address 0x0B9 + access_mode RW + modes M_SCSI + field FLXARBACK 0x80 + field FLXARBREQ 0x40 + field BRDADDR 0x38 + field BRDEN 0x04 + field BRDRW 0x02 + field BRDSTB 0x01 +} + +/* + * Serial EEPROM Address + */ +register SEEADR { + address 0x0BA + access_mode RW + modes M_SCSI +} + +/* + * Serial EEPROM Data + */ +register SEEDAT { + address 0x0BC + access_mode RW + size 2 + modes M_SCSI +} + +/* + * Serial EEPROM Status + */ +register SEESTAT { + address 0x0BE + access_mode RO + modes M_SCSI + field INIT_DONE 0x80 + field SEEOPCODE 0x70 + field LDALTID_L 0x08 + field SEEARBACK 0x04 + field SEEBUSY 0x02 + field SEESTART 0x01 +} + +/* + * Serial EEPROM Control + */ +register SEECTL { + address 0x0BE + access_mode RW + modes M_SCSI + field SEEOPCODE 0x70 { + SEEOP_ERASE 0x70, + SEEOP_READ 0x60, + SEEOP_WRITE 0x50, + /* + * The following four commands use special + * addresses for differentiation. + */ + SEEOP_ERAL 0x40 + } + mask SEEOP_EWEN 0x40 + mask SEEOP_WALL 0x40 + mask SEEOP_EWDS 0x40 + field SEERST 0x02 + field SEESTART 0x01 +} + +const SEEOP_ERAL_ADDR 0x80 +const SEEOP_EWEN_ADDR 0xC0 +const SEEOP_WRAL_ADDR 0x40 +const SEEOP_EWDS_ADDR 0x00 + +/* + * SCB Counter + */ +register SCBCNT { + address 0x0BF + access_mode RW + modes M_SCSI +} + +/* + * Data FIFO Write Address + * Pointer to the next QWD location to be written to the data FIFO. + */ +register DFWADDR { + address 0x0C0 + access_mode RW + size 2 + modes M_DFF0, M_DFF1 +} + +/* + * DSP Filter Control + */ +register DSPFLTRCTL { + address 0x0C0 + access_mode RW + modes M_CFG + field FLTRDISABLE 0x20 + field EDGESENSE 0x10 + field DSPFCNTSEL 0x0F +} + +/* + * DSP Data Channel Control + */ +register DSPDATACTL { + address 0x0C1 + access_mode RW + modes M_CFG + field BYPASSENAB 0x80 + field DESQDIS 0x10 + field RCVROFFSTDIS 0x04 + field XMITOFFSTDIS 0x02 +} + +/* + * Data FIFO Read Address + * Pointer to the next QWD location to be read from the data FIFO. + */ +register DFRADDR { + address 0x0C2 + access_mode RW + size 2 + modes M_DFF0, M_DFF1 +} + +/* + * DSP REQ Control + */ +register DSPREQCTL { + address 0x0C2 + access_mode RW + modes M_CFG + field MANREQCTL 0xC0 + field MANREQDLY 0x3F +} + +/* + * DSP ACK Control + */ +register DSPACKCTL { + address 0x0C3 + access_mode RW + modes M_CFG + field MANACKCTL 0xC0 + field MANACKDLY 0x3F +} + +/* + * Data FIFO Data + * Read/Write byte port into the data FIFO. The read and write + * FIFO pointers increment with each read and write respectively + * to this port. + */ +register DFDAT { + address 0x0C4 + access_mode RW + modes M_DFF0, M_DFF1 +} + +/* + * DSP Channel Select + */ +register DSPSELECT { + address 0x0C4 + access_mode RW + modes M_CFG + field AUTOINCEN 0x80 + field DSPSEL 0x1F +} + +const NUMDSPS 0x14 + +/* + * Write Bias Control + */ +register WRTBIASCTL { + address 0x0C5 + access_mode WO + modes M_CFG + field AUTOXBCDIS 0x80 + field XMITMANVAL 0x3F +} + +/* + * Currently the WRTBIASCTL is the same as the default. + */ +const WRTBIASCTL_HP_DEFAULT 0x0 + +/* + * Receiver Bias Control + */ +register RCVRBIOSCTL { + address 0x0C6 + access_mode WO + modes M_CFG + field AUTORBCDIS 0x80 + field RCVRMANVAL 0x3F +} + +/* + * Write Bias Calculator + */ +register WRTBIASCALC { + address 0x0C7 + access_mode RO + modes M_CFG +} + +/* + * Data FIFO Pointers + * Contains the byte offset from DFWADDR and DWRADDR to the current + * FIFO write/read locations. + */ +register DFPTRS { + address 0x0C8 + access_mode RW + modes M_DFF0, M_DFF1 +} + +/* + * Receiver Bias Calculator + */ +register RCVRBIASCALC { + address 0x0C8 + access_mode RO + modes M_CFG +} + +/* + * Data FIFO Backup Read Pointer + * Contains the data FIFO address to be restored if the last + * data accessed from the data FIFO was not transferred successfully. + */ +register DFBKPTR { + address 0x0C9 + access_mode RW + size 2 + modes M_DFF0, M_DFF1 +} + +/* + * Skew Calculator + */ +register SKEWCALC { + address 0x0C9 + access_mode RO + modes M_CFG +} + +/* + * Data FIFO Debug Control + */ +register DFDBCTL { + address 0x0CB + access_mode RW + modes M_DFF0, M_DFF1 + field DFF_CIO_WR_RDY 0x20 + field DFF_CIO_RD_RDY 0x10 + field DFF_DIR_ERR 0x08 + field DFF_RAMBIST_FAIL 0x04 + field DFF_RAMBIST_DONE 0x02 + field DFF_RAMBIST_EN 0x01 +} + +/* + * Data FIFO Space Count + * Number of FIFO locations that are free. + */ +register DFSCNT { + address 0x0CC + access_mode RO + size 2 + modes M_DFF0, M_DFF1 +} + +/* + * Data FIFO Byte Count + * Number of filled FIFO locations. + */ +register DFBCNT { + address 0x0CE + access_mode RO + size 2 + modes M_DFF0, M_DFF1 +} + +/* + * Sequencer Program Overlay Address. + * Low address must be written prior to high address. + */ +register OVLYADDR { + address 0x0D4 + modes M_SCSI + size 2 + access_mode RW +} + +/* + * Sequencer Control 0 + * Error detection mode, speed configuration, + * single step, breakpoints and program load. + */ +register SEQCTL0 { + address 0x0D6 + access_mode RW + field PERRORDIS 0x80 + field PAUSEDIS 0x40 + field FAILDIS 0x20 + field FASTMODE 0x10 + field BRKADRINTEN 0x08 + field STEP 0x04 + field SEQRESET 0x02 + field LOADRAM 0x01 +} + +/* + * Sequencer Control 1 + * Instruction RAM Diagnostics + */ +register SEQCTL1 { + address 0x0D7 + access_mode RW + field OVRLAY_DATA_CHK 0x08 + field RAMBIST_DONE 0x04 + field RAMBIST_FAIL 0x02 + field RAMBIST_EN 0x01 +} + +/* + * Sequencer Flags + * Zero and Carry state of the ALU. + */ +register FLAGS { + address 0x0D8 + access_mode RO + field ZERO 0x02 + field CARRY 0x01 +} + +/* + * Sequencer Interrupt Control + */ +register SEQINTCTL { + address 0x0D9 + access_mode RW + field INTVEC1DSL 0x80 + field INT1_CONTEXT 0x20 + field SCS_SEQ_INT1M1 0x10 + field SCS_SEQ_INT1M0 0x08 + field INTMASK2 0x04 + field INTMASK1 0x02 + field IRET 0x01 +} + +/* + * Sequencer RAM Data Port + * Single byte window into the Sequencer Instruction Ram area starting + * at the address specified by OVLYADDR. To write a full instruction word, + * simply write four bytes in succession. OVLYADDR will increment after the + * most significant instrution byte (the byte with the parity bit) is written. + */ +register SEQRAM { + address 0x0DA + access_mode RW +} + +/* + * Sequencer Program Counter + * Low byte must be written prior to high byte. + */ +register PRGMCNT { + address 0x0DE + access_mode RW + size 2 +} + +/* + * Accumulator + */ +register ACCUM { + address 0x0E0 + access_mode RW + accumulator +} + +/* + * Source Index Register + * Incrementing index for reads of SINDIR and the destination (low byte only) + * for any immediate operands passed in jmp, jc, jnc, call instructions. + * Example: + * mvi 0xFF call some_routine; + * + * Will set SINDEX[0] to 0xFF and call the routine "some_routine. + */ +register SINDEX { + address 0x0E2 + access_mode RW + size 2 + sindex +} + +/* + * Destination Index Register + * Incrementing index for writes to DINDIR. Can be used as a scratch register. + */ +register DINDEX { + address 0x0E4 + access_mode RW + size 2 +} + +/* + * Break Address + * Sequencer instruction breakpoint address address. + */ +register BRKADDR0 { + address 0x0E6 + access_mode RW +} + +register BRKADDR1 { + address 0x0E6 + access_mode RW + field BRKDIS 0x80 /* Disable Breakpoint */ +} + +/* + * All Ones + * All reads to this register return the value 0xFF. + */ +register ALLONES { + address 0x0E8 + access_mode RO + allones +} + +/* + * All Zeros + * All reads to this register return the value 0. + */ +register ALLZEROS { + address 0x0EA + access_mode RO + allzeros +} + +/* + * No Destination + * Writes to this register have no effect. + */ +register NONE { + address 0x0EA + access_mode WO + none +} + +/* + * Source Index Indirect + * Reading this register is equivalent to reading (register_base + SINDEX) and + * incrementing SINDEX by 1. + */ +register SINDIR { + address 0x0EC + access_mode RO +} + +/* + * Destination Index Indirect + * Writing this register is equivalent to writing to (register_base + DINDEX) + * and incrementing DINDEX by 1. + */ +register DINDIR { + address 0x0ED + access_mode WO +} + +/* + * Function One + * 2's complement to bit value conversion. Write the 2's complement value + * (0-7 only) to the top nibble and retrieve the bit indexed by that value + * on the next read of this register. + * Example: + * Write 0x60 + * Read 0x40 + */ +register FUNCTION1 { + address 0x0F0 + access_mode RW +} + +/* + * Stack + * Window into the stack. Each stack location is 10 bits wide reported + * low byte followed by high byte. There are 8 stack locations. + */ +register STACK { + address 0x0F2 + access_mode RW +} + +/* + * Interrupt Vector 1 Address + * Interrupt branch address for SCS SEQ_INT1 mode 0 and 1 interrupts. + */ +register INTVEC1_ADDR { + address 0x0F4 + access_mode RW + size 2 + modes M_CFG +} + +/* + * Current Address + * Address of the SEQRAM instruction currently executing instruction. + */ +register CURADDR { + address 0x0F4 + access_mode RW + size 2 + modes M_SCSI +} + +/* + * Interrupt Vector 2 Address + * Interrupt branch address for HST_SEQ_INT2 interrupts. + */ +register INTVEC2_ADDR { + address 0x0F6 + access_mode RW + size 2 + modes M_CFG +} + +/* + * Last Address + * Address of the SEQRAM instruction executed prior to the current instruction. + */ +register LASTADDR { + address 0x0F6 + access_mode RW + size 2 + modes M_SCSI +} + +register AHD_PCI_CONFIG_BASE { + address 0x100 + access_mode RW + size 256 + modes M_CFG +} + +/* ---------------------- Scratch RAM Offsets ------------------------- */ +scratch_ram { + /* Mode Specific */ + address 0x0A0 + size 8 + modes 0, 1, 2, 3 + REG0 { + size 2 + } + REG1 { + size 2 + } + REG_ISR { + size 2 + } + SG_STATE { + size 1 + field SEGS_AVAIL 0x01 + field LOADING_NEEDED 0x02 + field FETCH_INPROG 0x04 + } + /* + * Track whether the transfer byte count for + * the current data phase is odd. + */ + DATA_COUNT_ODD { + size 1 + } +} + +scratch_ram { + /* Mode Specific */ + address 0x0F8 + size 8 + modes 0, 1, 2, 3 + LONGJMP_ADDR { + size 2 + } + ACCUM_SAVE { + size 1 + } +} + + +scratch_ram { + address 0x100 + size 128 + modes 0, 1, 2, 3 + /* + * Per "other-id" execution queues. We use an array of + * tail pointers into lists of SCBs sorted by "other-id". + * The execution head pointer threads the head SCBs for + * each list. + */ + WAITING_SCB_TAILS { + size 32 + } + WAITING_TID_HEAD { + size 2 + } + WAITING_TID_TAIL { + size 2 + } + /* + * SCBID of the next SCB in the new SCB queue. + */ + NEXT_QUEUED_SCB_ADDR { + size 4 + } + /* + * head of list of SCBs that have + * completed but have not been + * put into the qoutfifo. + */ + COMPLETE_SCB_HEAD { + size 2 + } + /* + * The list of completed SCBs in + * the active DMA. + */ + COMPLETE_SCB_DMAINPROG_HEAD { + size 2 + } + /* + * head of list of SCBs that have + * completed but need to be uploaded + * to the host prior to being completed. + */ + COMPLETE_DMA_SCB_HEAD { + size 2 + } + /* Counting semaphore to prevent new select-outs */ + QFREEZE_COUNT { + size 2 + } + /* + * Mode to restore on legacy idle loop exit. + */ + SAVED_MODE { + size 1 + } + /* + * Single byte buffer used to designate the type or message + * to send to a target. + */ + MSG_OUT { + size 1 + } + /* Parameters for DMA Logic */ + DMAPARAMS { + size 1 + field PRELOADEN 0x80 + field WIDEODD 0x40 + field SCSIEN 0x20 + field SDMAEN 0x10 + field SDMAENACK 0x10 + field HDMAEN 0x08 + field HDMAENACK 0x08 + field DIRECTION 0x04 /* Set indicates PCI->SCSI */ + field FIFOFLUSH 0x02 + field FIFORESET 0x01 + } + SEQ_FLAGS { + size 1 + field NOT_IDENTIFIED 0x80 + field NO_CDB_SENT 0x40 + field TARGET_CMD_IS_TAGGED 0x40 + field DPHASE 0x20 + /* Target flags */ + field TARG_CMD_PENDING 0x10 + field CMDPHASE_PENDING 0x08 + field DPHASE_PENDING 0x04 + field SPHASE_PENDING 0x02 + field NO_DISCONNECT 0x01 + } + /* + * Temporary storage for the + * target/channel/lun of a + * reconnecting target + */ + SAVED_SCSIID { + size 1 + } + SAVED_LUN { + size 1 + } + /* + * The last bus phase as seen by the sequencer. + */ + LASTPHASE { + size 1 + field CDI 0x80 + field IOI 0x40 + field MSGI 0x20 + field P_BUSFREE 0x01 + enum PHASE_MASK CDO|IOO|MSGO { + P_DATAOUT 0x0, + P_DATAIN IOO, + P_DATAOUT_DT P_DATAOUT|MSGO, + P_DATAIN_DT P_DATAIN|MSGO, + P_COMMAND CDO, + P_MESGOUT CDO|MSGO, + P_STATUS CDO|IOO, + P_MESGIN CDO|IOO|MSGO + } + } + /* + * Value to "or" into the SCBPTR[1] value to + * indicate that an entry in the QINFIFO is valid. + */ + QOUTFIFO_ENTRY_VALID_TAG { + size 1 + } + /* + * Base address of our shared data with the kernel driver in host + * memory. This includes the qoutfifo and target mode + * incoming command queue. + */ + SHARED_DATA_ADDR { + size 4 + } + /* + * Pointer to location in host memory for next + * position in the qoutfifo. + */ + QOUTFIFO_NEXT_ADDR { + size 4 + } + /* + * Kernel and sequencer offsets into the queue of + * incoming target mode command descriptors. The + * queue is full when the KERNEL_TQINPOS == TQINPOS. + */ + KERNEL_TQINPOS { + size 1 + } + TQINPOS { + size 1 + } + ARG_1 { + size 1 + mask SEND_MSG 0x80 + mask SEND_SENSE 0x40 + mask SEND_REJ 0x20 + mask MSGOUT_PHASEMIS 0x10 + mask EXIT_MSG_LOOP 0x08 + mask CONT_MSG_LOOP_WRITE 0x04 + mask CONT_MSG_LOOP_READ 0x03 + mask CONT_MSG_LOOP_TARG 0x02 + alias RETURN_1 + } + ARG_2 { + size 1 + alias RETURN_2 + } + + /* + * Snapshot of MSG_OUT taken after each message is sent. + */ + LAST_MSG { + size 1 + } + + /* + * Sequences the kernel driver has okayed for us. This allows + * the driver to do things like prevent initiator or target + * operations. + */ + SCSISEQ_TEMPLATE { + size 1 + field MANUALCTL 0x40 + field ENSELI 0x20 + field ENRSELI 0x10 + field MANUALP 0x0C + field ENAUTOATNP 0x02 + field ALTSTIM 0x01 + } + + /* + * The initiator specified tag for this target mode transaction. + */ + INITIATOR_TAG { + size 1 + } + + SEQ_FLAGS2 { + size 1 + field TARGET_MSG_PENDING 0x02 + field SELECTOUT_QFROZEN 0x04 + } + + ALLOCFIFO_SCBPTR { + size 2 + } + + /* + * The maximum amount of time to wait, when interrupt coalescing + * is enabled, before issueing a CMDCMPLT interrupt for a completed + * command. + */ + INT_COALESCING_TIMER { + size 2 + } + + /* + * The maximum number of commands to coalesce into a single interrupt. + * Actually the 2's complement of that value to simplify sequencer + * code. + */ + INT_COALESCING_MAXCMDS { + size 1 + } + + /* + * The minimum number of commands still outstanding required + * to continue coalescing (2's complement of value). + */ + INT_COALESCING_MINCMDS { + size 1 + } + + /* + * Number of commands "in-flight". + */ + CMDS_PENDING { + size 2 + } + + /* + * The count of commands that have been coalesced. + */ + INT_COALESCING_CMDCOUNT { + size 1 + } + + /* + * Since the HS_MAIBOX is self clearing, copy its contents to + * this position in scratch ram every time it changes. + */ + LOCAL_HS_MAILBOX { + size 1 + } + /* + * Target-mode CDB type to CDB length table used + * in non-packetized operation. + */ + CMDSIZE_TABLE { + size 8 + } +} + +/************************* Hardware SCB Definition ****************************/ +scb { + address 0x180 + size 64 + modes 0, 1, 2, 3 + SCB_RESIDUAL_DATACNT { + size 4 + alias SCB_CDB_STORE + alias SCB_HOST_CDB_PTR + } + SCB_RESIDUAL_SGPTR { + size 4 + field SG_ADDR_MASK 0xf8 /* In the last byte */ + field SG_OVERRUN_RESID 0x02 /* In the first byte */ + field SG_LIST_NULL 0x01 /* In the first byte */ + } + SCB_SCSI_STATUS { + size 1 + alias SCB_HOST_CDB_LEN + } + SCB_TARGET_PHASES { + size 1 + } + SCB_TARGET_DATA_DIR { + size 1 + } + SCB_TARGET_ITAG { + size 1 + } + SCB_SENSE_BUSADDR { + /* + * Only valid if CDB length is less than 13 bytes or + * we are using a CDB pointer. Otherwise contains + * the last 4 bytes of embedded cdb information. + */ + size 4 + alias SCB_NEXT_COMPLETE + } + SCB_TAG { + alias SCB_FIFO_USE_COUNT + size 2 + } + SCB_CONTROL { + size 1 + field TARGET_SCB 0x80 + field DISCENB 0x40 + field TAG_ENB 0x20 + field MK_MESSAGE 0x10 + field STATUS_RCVD 0x08 + field DISCONNECTED 0x04 + field SCB_TAG_TYPE 0x03 + } + SCB_SCSIID { + size 1 + field TID 0xF0 + field OID 0x0F + } + SCB_LUN { + size 1 + field LID 0xff + } + SCB_TASK_ATTRIBUTE { + size 1 + /* + * Overloaded field for non-packetized + * ignore wide residue message handling. + */ + field SCB_XFERLEN_ODD 0x01 + } + SCB_CDB_LEN { + size 1 + field SCB_CDB_LEN_PTR 0x80 /* CDB in host memory */ + } + SCB_TASK_MANAGEMENT { + size 1 + } + SCB_DATAPTR { + size 8 + } + SCB_DATACNT { + /* + * The last byte is really the high address bits for + * the data address. + */ + size 4 + field SG_LAST_SEG 0x80 /* In the fourth byte */ + field SG_HIGH_ADDR_BITS 0x7F /* In the fourth byte */ + } + SCB_SGPTR { + size 4 + field SG_STATUS_VALID 0x04 /* In the first byte */ + field SG_FULL_RESID 0x02 /* In the first byte */ + field SG_LIST_NULL 0x01 /* In the first byte */ + } + SCB_BUSADDR { + size 4 + } + SCB_NEXT { + alias SCB_NEXT_SCB_BUSADDR + size 2 + } + SCB_NEXT2 { + size 2 + } + SCB_SPARE { + size 8 + alias SCB_PKT_LUN + } + SCB_DISCONNECTED_LISTS { + size 8 + } +} + +/*********************************** Constants ********************************/ +const MK_MESSAGE_BIT_OFFSET 4 +const TID_SHIFT 4 +const TARGET_CMD_CMPLT 0xfe +const INVALID_ADDR 0x80 +#define SCB_LIST_NULL 0xff +#define QOUTFIFO_ENTRY_VALID_TOGGLE 0x80 + +const CCSGADDR_MAX 0x80 +const CCSCBADDR_MAX 0x80 +const CCSGRAM_MAXSEGS 16 + +/* Selection Timeout Timer Constants */ +const STIMESEL_SHIFT 3 +const STIMESEL_MIN 0x18 +const STIMESEL_BUG_ADJ 0x8 + +/* WDTR Message values */ +const BUS_8_BIT 0x00 +const BUS_16_BIT 0x01 +const BUS_32_BIT 0x02 + +/* Offset maximums */ +const MAX_OFFSET 0xfe +const MAX_OFFSET_PACED 0xfe +const MAX_OFFSET_PACED_BUG 0x7f +/* + * Some 160 devices incorrectly accept 0xfe as a + * sync offset, but will overrun this value. Limit + * to 0x7f for speed lower than U320 which will + * avoid the persistent sync offset overruns. + */ +const MAX_OFFSET_NON_PACED 0x7f +const HOST_MSG 0xff + +/* + * The size of our sense buffers. + * Sense buffer mapping can be handled in either of two ways. + * The first is to allocate a dmamap for each transaction. + * Depending on the architecture, dmamaps can be costly. The + * alternative is to statically map the buffers in much the same + * way we handle our scatter gather lists. The driver implements + * the later. + */ +const AHD_SENSE_BUFSIZE 256 + +/* Target mode command processing constants */ +const CMD_GROUP_CODE_SHIFT 0x05 + +const STATUS_BUSY 0x08 +const STATUS_QUEUE_FULL 0x28 +const STATUS_PKT_SENSE 0xFF +const TARGET_DATA_IN 1 + +const SCB_TRANSFER_SIZE_FULL_LUN 56 +const SCB_TRANSFER_SIZE_1BYTE_LUN 48 +/* PKT_OVERRUN_BUFSIZE must be a multiple of 256 less than 64K */ +const PKT_OVERRUN_BUFSIZE 512 + +/* + * Timer parameters. + */ +const AHD_TIMER_US_PER_TICK 25 +const AHD_TIMER_MAX_TICKS 0xFFFF +const AHD_TIMER_MAX_US (AHD_TIMER_MAX_TICKS * AHD_TIMER_US_PER_TICK) + +/* + * Downloaded (kernel inserted) constants + */ +const SG_PREFETCH_CNT download +const SG_PREFETCH_CNT_LIMIT download +const SG_PREFETCH_ALIGN_MASK download +const SG_PREFETCH_ADDR_MASK download +const SG_SIZEOF download +const PKT_OVERRUN_BUFOFFSET download +const SCB_TRANSFER_SIZE download + +/* + * BIOS SCB offsets + */ +const NVRAM_SCB_OFFSET 0x2C |