diff options
Diffstat (limited to 'drivers/scsi/aic7xxx/Kconfig.aic7xxx')
| -rw-r--r-- | drivers/scsi/aic7xxx/Kconfig.aic7xxx | 100 |
1 files changed, 100 insertions, 0 deletions
diff --git a/drivers/scsi/aic7xxx/Kconfig.aic7xxx b/drivers/scsi/aic7xxx/Kconfig.aic7xxx new file mode 100644 index 00000000000..8398e0dd481 --- /dev/null +++ b/drivers/scsi/aic7xxx/Kconfig.aic7xxx @@ -0,0 +1,100 @@ +# +# AIC7XXX and AIC79XX 2.5.X Kernel configuration File. +# $Id: //depot/linux-aic79xx-2.5.0/drivers/scsi/aic7xxx/Kconfig.aic7xxx#7 $ +# +config SCSI_AIC7XXX + tristate "Adaptec AIC7xxx Fast -> U160 support (New Driver)" + depends on (PCI || EISA) && SCSI + ---help--- + This driver supports all of Adaptec's Fast through Ultra 160 PCI + based SCSI controllers as well as the aic7770 based EISA and VLB + SCSI controllers (the 274x and 284x series). For AAA and ARO based + configurations, only SCSI functionality is provided. + + To compile this driver as a module, choose M here: the + module will be called aic7xxx. + +config AIC7XXX_CMDS_PER_DEVICE + int "Maximum number of TCQ commands per device" + depends on SCSI_AIC7XXX + default "32" + ---help--- + Specify the number of commands you would like to allocate per SCSI + device when Tagged Command Queueing (TCQ) is enabled on that device. + + This is an upper bound value for the number of tagged transactions + to be used for any device. The aic7xxx driver will automatically + vary this number based on device behavior. For devices with a + fixed maximum, the driver will eventually lock to this maximum + and display a console message inidicating this value. + + Due to resource allocation issues in the Linux SCSI mid-layer, using + a high number of commands per device may result in memory allocation + failures when many devices are attached to the system. For this reason, + the default is set to 32. Higher values may result in higer performance + on some devices. The upper bound is 253. 0 disables tagged queueing. + + Per device tag depth can be controlled via the kernel command line + "tag_info" option. See drivers/scsi/aic7xxx/README.aic7xxx + for details. + +config AIC7XXX_RESET_DELAY_MS + int "Initial bus reset delay in milli-seconds" + depends on SCSI_AIC7XXX + default "15000" + ---help--- + The number of milliseconds to delay after an initial bus reset. + The bus settle delay following all error recovery actions is + dictated by the SCSI layer and is not affected by this value. + + Default: 15000 (15 seconds) + +config AIC7XXX_PROBE_EISA_VL + bool "Probe for EISA and VL AIC7XXX Adapters" + depends on SCSI_AIC7XXX && EISA + help + Probe for EISA and VLB Aic7xxx controllers. In many newer systems, + the invasive probes necessary to detect these controllers can cause + other devices to fail. For this reason, the non-PCI probe code is + disabled by default. The current value of this option can be "toggled" + via the no_probe kernel command line option. + +config AIC7XXX_BUILD_FIRMWARE + bool "Build Adapter Firmware with Kernel Build" + depends on SCSI_AIC7XXX && !PREVENT_FIRMWARE_BUILD + help + This option should only be enabled if you are modifying the firmware + source to the aic7xxx driver and wish to have the generated firmware + include files updated during a normal kernel build. The assembler + for the firmware requires lex and yacc or their equivalents, as well + as the db v1 library. You may have to install additional packages + or modify the assembler Makefile or the files it includes if your + build environment is different than that of the author. + +config AIC7XXX_DEBUG_ENABLE + bool "Compile in Debugging Code" + depends on SCSI_AIC7XXX + default y + help + Compile in aic7xxx debugging code that can be useful in diagnosing + driver errors. + +config AIC7XXX_DEBUG_MASK + int "Debug code enable mask (2047 for all debugging)" + depends on SCSI_AIC7XXX + default "0" + help + Bit mask of debug options that is only valid if the + CONFIG_AIC7XXX_DEBUG_ENBLE option is enabled. The bits in this mask + are defined in the drivers/scsi/aic7xxx/aic7xxx.h - search for the + variable ahc_debug in that file to find them. + +config AIC7XXX_REG_PRETTY_PRINT + bool "Decode registers during diagnostics" + depends on SCSI_AIC7XXX + default y + help + Compile in register value tables for the output of expanded register + contents in diagnostics. This make it much easier to understand debug + output without having to refer to a data book and/or the aic7xxx.reg + file. |