diff options
Diffstat (limited to 'drivers/power/ab8500_charger.c')
| -rw-r--r-- | drivers/power/ab8500_charger.c | 24 |
1 files changed, 12 insertions, 12 deletions
diff --git a/drivers/power/ab8500_charger.c b/drivers/power/ab8500_charger.c index d27dd7fec16..21dc8422778 100644 --- a/drivers/power/ab8500_charger.c +++ b/drivers/power/ab8500_charger.c @@ -189,7 +189,7 @@ struct ab8500_charger_usb_state { * @autopower_cfg platform specific power config support for "pwron after pwrloss" * @parent: Pointer to the struct ab8500 * @gpadc: Pointer to the struct gpadc - * @bat: Pointer to the abx500_bm platform data + * @bm: Platform specific battery management information * @flags: Structure for information about events triggered * @usb_state: Structure for usb stack information * @ac_chg: AC charger power supply @@ -226,7 +226,7 @@ struct ab8500_charger { bool autopower_cfg; struct ab8500 *parent; struct ab8500_gpadc *gpadc; - struct abx500_bm_data *bat; + struct abx500_bm_data *bm; struct ab8500_charger_event_flags flags; struct ab8500_charger_usb_state usb_state; struct ux500_charger ac_chg; @@ -1034,7 +1034,7 @@ static int ab8500_charger_set_vbus_in_curr(struct ab8500_charger *di, int min_value; /* We should always use to lowest current limit */ - min_value = min(di->bat->chg_params->usb_curr_max, ich_in); + min_value = min(di->bm->chg_params->usb_curr_max, ich_in); switch (min_value) { case 100: @@ -1176,7 +1176,7 @@ static int ab8500_charger_ac_en(struct ux500_charger *charger, volt_index = ab8500_voltage_to_regval(vset); curr_index = ab8500_current_to_regval(iset); input_curr_index = ab8500_current_to_regval( - di->bat->chg_params->ac_curr_max); + di->bm->chg_params->ac_curr_max); if (volt_index < 0 || curr_index < 0 || input_curr_index < 0) { dev_err(di->dev, "Charger voltage or current too high, " @@ -1193,7 +1193,7 @@ static int ab8500_charger_ac_en(struct ux500_charger *charger, } /* MainChInputCurr: current that can be drawn from the charger*/ ret = ab8500_charger_set_main_in_curr(di, - di->bat->chg_params->ac_curr_max); + di->bm->chg_params->ac_curr_max); if (ret) { dev_err(di->dev, "%s Failed to set MainChInputCurr\n", __func__); @@ -1209,7 +1209,7 @@ static int ab8500_charger_ac_en(struct ux500_charger *charger, } /* Check if VBAT overshoot control should be enabled */ - if (!di->bat->enable_overshoot) + if (!di->bm->enable_overshoot) overshoot = MAIN_CH_NO_OVERSHOOT_ENA_N; /* Enable Main Charger */ @@ -1376,7 +1376,7 @@ static int ab8500_charger_usb_en(struct ux500_charger *charger, return ret; } /* Check if VBAT overshoot control should be enabled */ - if (!di->bat->enable_overshoot) + if (!di->bm->enable_overshoot) overshoot = USB_CHG_NO_OVERSHOOT_ENA_N; /* Enable USB Charger */ @@ -2454,8 +2454,8 @@ static int ab8500_charger_init_hw_registers(struct ab8500_charger *di) ret = abx500_set_register_interruptible(di->dev, AB8500_RTC, AB8500_RTC_BACKUP_CHG_REG, - di->bat->bkup_bat_v | - di->bat->bkup_bat_i); + di->bm->bkup_bat_v | + di->bm->bkup_bat_i); if (ret) { dev_err(di->dev, "failed to setup backup battery charging\n"); goto out; @@ -2644,10 +2644,10 @@ static int __devinit ab8500_charger_probe(struct platform_device *pdev) dev_err(&pdev->dev, "%s no mem for ab8500_charger\n", __func__); return -ENOMEM; } - di->bat = pdev->mfd_cell->platform_data; - if (!di->bat) { + di->bm = pdev->mfd_cell->platform_data; + if (!di->bm) { if (np) { - ret = bmdevs_of_probe(&pdev->dev, np, &di->bat); + ret = ab8500_bm_of_probe(&pdev->dev, np, &di->bm); if (ret) { dev_err(&pdev->dev, "failed to get battery information\n"); |