diff options
Diffstat (limited to 'drivers/pcmcia/sa11xx_base.c')
| -rw-r--r-- | drivers/pcmcia/sa11xx_base.c | 200 |
1 files changed, 200 insertions, 0 deletions
diff --git a/drivers/pcmcia/sa11xx_base.c b/drivers/pcmcia/sa11xx_base.c new file mode 100644 index 00000000000..db04ffb6f68 --- /dev/null +++ b/drivers/pcmcia/sa11xx_base.c @@ -0,0 +1,200 @@ +/*====================================================================== + + Device driver for the PCMCIA control functionality of StrongARM + SA-1100 microprocessors. + + The contents of this file are subject to the Mozilla Public + License Version 1.1 (the "License"); you may not use this file + except in compliance with the License. You may obtain a copy of + the License at http://www.mozilla.org/MPL/ + + Software distributed under the License is distributed on an "AS + IS" basis, WITHOUT WARRANTY OF ANY KIND, either express or + implied. See the License for the specific language governing + rights and limitations under the License. + + The initial developer of the original code is John G. Dorsey + <john+@cs.cmu.edu>. Portions created by John G. Dorsey are + Copyright (C) 1999 John G. Dorsey. All Rights Reserved. + + Alternatively, the contents of this file may be used under the + terms of the GNU Public License version 2 (the "GPL"), in which + case the provisions of the GPL are applicable instead of the + above. If you wish to allow the use of your version of this file + only under the terms of the GPL and not to allow others to use + your version of this file under the MPL, indicate your decision + by deleting the provisions above and replace them with the notice + and other provisions required by the GPL. If you do not delete + the provisions above, a recipient may use your version of this + file under either the MPL or the GPL. + +======================================================================*/ + +#include <linux/module.h> +#include <linux/init.h> +#include <linux/config.h> +#include <linux/cpufreq.h> +#include <linux/ioport.h> +#include <linux/kernel.h> +#include <linux/spinlock.h> + +#include <asm/hardware.h> +#include <asm/io.h> +#include <asm/irq.h> +#include <asm/system.h> + +#include "soc_common.h" +#include "sa11xx_base.h" + + +/* + * sa1100_pcmcia_default_mecr_timing + * ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ + * + * Calculate MECR clock wait states for given CPU clock + * speed and command wait state. This function can be over- + * written by a board specific version. + * + * The default is to simply calculate the BS values as specified in + * the INTEL SA1100 development manual + * "Expansion Memory (PCMCIA) Configuration Register (MECR)" + * that's section 10.2.5 in _my_ version of the manual ;) + */ +static unsigned int +sa1100_pcmcia_default_mecr_timing(struct soc_pcmcia_socket *skt, + unsigned int cpu_speed, + unsigned int cmd_time) +{ + return sa1100_pcmcia_mecr_bs(cmd_time, cpu_speed); +} + +/* sa1100_pcmcia_set_mecr() + * ^^^^^^^^^^^^^^^^^^^^^^^^ + * + * set MECR value for socket <sock> based on this sockets + * io, mem and attribute space access speed. + * Call board specific BS value calculation to allow boards + * to tweak the BS values. + */ +static int +sa1100_pcmcia_set_mecr(struct soc_pcmcia_socket *skt, unsigned int cpu_clock) +{ + struct soc_pcmcia_timing timing; + u32 mecr, old_mecr; + unsigned long flags; + unsigned int bs_io, bs_mem, bs_attr; + + soc_common_pcmcia_get_timing(skt, &timing); + + bs_io = skt->ops->get_timing(skt, cpu_clock, timing.io); + bs_mem = skt->ops->get_timing(skt, cpu_clock, timing.mem); + bs_attr = skt->ops->get_timing(skt, cpu_clock, timing.attr); + + local_irq_save(flags); + + old_mecr = mecr = MECR; + MECR_FAST_SET(mecr, skt->nr, 0); + MECR_BSIO_SET(mecr, skt->nr, bs_io); + MECR_BSA_SET(mecr, skt->nr, bs_attr); + MECR_BSM_SET(mecr, skt->nr, bs_mem); + if (old_mecr != mecr) + MECR = mecr; + + local_irq_restore(flags); + + debug(skt, 2, "FAST %X BSM %X BSA %X BSIO %X\n", + MECR_FAST_GET(mecr, skt->nr), + MECR_BSM_GET(mecr, skt->nr), MECR_BSA_GET(mecr, skt->nr), + MECR_BSIO_GET(mecr, skt->nr)); + + return 0; +} + +#ifdef CONFIG_CPU_FREQ +static int +sa1100_pcmcia_frequency_change(struct soc_pcmcia_socket *skt, + unsigned long val, + struct cpufreq_freqs *freqs) +{ + switch (val) { + case CPUFREQ_PRECHANGE: + if (freqs->new > freqs->old) + sa1100_pcmcia_set_mecr(skt, freqs->new); + break; + + case CPUFREQ_POSTCHANGE: + if (freqs->new < freqs->old) + sa1100_pcmcia_set_mecr(skt, freqs->new); + break; + case CPUFREQ_RESUMECHANGE: + sa1100_pcmcia_set_mecr(skt, freqs->new); + break; + } + + return 0; +} + +#endif + +static int +sa1100_pcmcia_set_timing(struct soc_pcmcia_socket *skt) +{ + return sa1100_pcmcia_set_mecr(skt, cpufreq_get(0)); +} + +static int +sa1100_pcmcia_show_timing(struct soc_pcmcia_socket *skt, char *buf) +{ + struct soc_pcmcia_timing timing; + unsigned int clock = cpufreq_get(0); + unsigned long mecr = MECR; + char *p = buf; + + soc_common_pcmcia_get_timing(skt, &timing); + + p+=sprintf(p, "I/O : %u (%u)\n", timing.io, + sa1100_pcmcia_cmd_time(clock, MECR_BSIO_GET(mecr, skt->nr))); + + p+=sprintf(p, "attribute: %u (%u)\n", timing.attr, + sa1100_pcmcia_cmd_time(clock, MECR_BSA_GET(mecr, skt->nr))); + + p+=sprintf(p, "common : %u (%u)\n", timing.mem, + sa1100_pcmcia_cmd_time(clock, MECR_BSM_GET(mecr, skt->nr))); + + return p - buf; +} + +int sa11xx_drv_pcmcia_probe(struct device *dev, struct pcmcia_low_level *ops, + int first, int nr) +{ + /* + * set default MECR calculation if the board specific + * code did not specify one... + */ + if (!ops->get_timing) + ops->get_timing = sa1100_pcmcia_default_mecr_timing; + + /* Provide our SA11x0 specific timing routines. */ + ops->set_timing = sa1100_pcmcia_set_timing; + ops->show_timing = sa1100_pcmcia_show_timing; +#ifdef CONFIG_CPU_FREQ + ops->frequency_change = sa1100_pcmcia_frequency_change; +#endif + + return soc_common_drv_pcmcia_probe(dev, ops, first, nr); +} +EXPORT_SYMBOL(sa11xx_drv_pcmcia_probe); + +static int __init sa11xx_pcmcia_init(void) +{ + return 0; +} +module_init(sa11xx_pcmcia_init); + +static void __exit sa11xx_pcmcia_exit(void) {} + +module_exit(sa11xx_pcmcia_exit); + +MODULE_AUTHOR("John Dorsey <john+@cs.cmu.edu>"); +MODULE_DESCRIPTION("Linux PCMCIA Card Services: SA-11xx core socket driver"); +MODULE_LICENSE("Dual MPL/GPL"); |