diff options
Diffstat (limited to 'drivers/net')
61 files changed, 91 insertions, 86 deletions
diff --git a/drivers/net/82596.c b/drivers/net/82596.c index ea6b139b812..1663bc9e45d 100644 --- a/drivers/net/82596.c +++ b/drivers/net/82596.c @@ -19,7 +19,7 @@ TBD: * look at deferring rx frames rather than discarding (as per tulip) * handle tx ring full as per tulip - * performace test to tune rx_copybreak + * performance test to tune rx_copybreak Most of my modifications relate to the braindead big-endian implementation by Intel. When the i596 is operating in diff --git a/drivers/net/amd8111e.c b/drivers/net/amd8111e.c index 4e6359fff0e..766aabfdfc7 100644 --- a/drivers/net/amd8111e.c +++ b/drivers/net/amd8111e.c @@ -1633,8 +1633,13 @@ static int amd8111e_enable_link_change(struct amd8111e_priv* lp) readl(lp->mmio + CMD7); return 0; } -/* This function is called when a packet transmission fails to complete within a resonable period, on the assumption that an interrupts have been failed or the interface is locked up. This function will reinitialize the hardware */ +/* + * This function is called when a packet transmission fails to complete + * within a reasonable period, on the assumption that an interrupt have + * failed or the interface is locked up. This function will reinitialize + * the hardware. + */ static void amd8111e_tx_timeout(struct net_device *dev) { struct amd8111e_priv* lp = netdev_priv(dev); diff --git a/drivers/net/appletalk/cops.c b/drivers/net/appletalk/cops.c index b5dc7f55072..9d828aed968 100644 --- a/drivers/net/appletalk/cops.c +++ b/drivers/net/appletalk/cops.c @@ -120,7 +120,7 @@ static int irq = 5; /* Default IRQ */ * DAYNA driver mode: * Dayna DL2000/DaynaTalk PC (Half Length), COPS LT-95, * Farallon PhoneNET PC III, Farallon PhoneNET PC II - * Other cards possibly supported mode unkown though: + * Other cards possibly supported mode unknown though: * Dayna DL2000 (Full length), COPS LT/M (Micro-Channel) * * Cards NOT supported by this driver but supported by the ltpc.c diff --git a/drivers/net/ariadne.h b/drivers/net/ariadne.h index bb613f292e0..727be5cdd1e 100644 --- a/drivers/net/ariadne.h +++ b/drivers/net/ariadne.h @@ -244,7 +244,7 @@ struct Am79C960 { #define DLNKTST 0x0010 /* Disable Link Status */ #define DAPC 0x0008 /* Disable Automatic Polarity Correction */ #define MENDECL 0x0004 /* MENDEC Loopback Mode */ -#define LRTTSEL 0x0002 /* Low Receive Treshold/Transmit Mode Select */ +#define LRTTSEL 0x0002 /* Low Receive Threshold/Transmit Mode Select */ #define PORTSEL1 0x0001 /* Port Select Bits */ #define PORTSEL2 0x8000 /* Port Select Bits */ #define INTL 0x4000 /* Internal Loopback */ diff --git a/drivers/net/atl1c/atl1c_main.c b/drivers/net/atl1c/atl1c_main.c index 1372e9a99f5..96506eacc13 100644 --- a/drivers/net/atl1c/atl1c_main.c +++ b/drivers/net/atl1c/atl1c_main.c @@ -1543,7 +1543,7 @@ static irqreturn_t atl1c_intr(int irq, void *data) if (status & ISR_OVER) if (netif_msg_intr(adapter)) dev_warn(&pdev->dev, - "TX/RX over flow (status = 0x%x)\n", + "TX/RX overflow (status = 0x%x)\n", status & ISR_OVER); /* link event */ diff --git a/drivers/net/benet/be_cmds.h b/drivers/net/benet/be_cmds.h index e5f9676cf1b..21f40779f52 100644 --- a/drivers/net/benet/be_cmds.h +++ b/drivers/net/benet/be_cmds.h @@ -435,7 +435,7 @@ enum be_if_flags { * filtering capabilities. */ struct be_cmd_req_if_create { struct be_cmd_req_hdr hdr; - u32 version; /* ignore currntly */ + u32 version; /* ignore currently */ u32 capability_flags; u32 enable_flags; u8 mac_addr[ETH_ALEN]; diff --git a/drivers/net/benet/be_main.c b/drivers/net/benet/be_main.c index 876b357101f..c3a7db326c9 100644 --- a/drivers/net/benet/be_main.c +++ b/drivers/net/benet/be_main.c @@ -1877,7 +1877,7 @@ int be_load_fw(struct be_adapter *adapter, u8 *func) goto fw_exit; } - dev_info(&adapter->pdev->dev, "Firmware flashed succesfully\n"); + dev_info(&adapter->pdev->dev, "Firmware flashed successfully\n"); fw_exit: release_firmware(fw); diff --git a/drivers/net/bnx2x_reg.h b/drivers/net/bnx2x_reg.h index aa76cbada5e..732eafdeb0f 100644 --- a/drivers/net/bnx2x_reg.h +++ b/drivers/net/bnx2x_reg.h @@ -2536,7 +2536,7 @@ /* [RC 1] A flag to indicate that overflow error occurred in one of the queues. */ #define QM_REG_OVFERROR 0x16805c -/* [RC 7] the Q were the qverflow occurs */ +/* [RC 7] the Q where the overflow occurs */ #define QM_REG_OVFQNUM 0x168058 /* [R 16] Pause state for physical queues 15-0 */ #define QM_REG_PAUSESTATE0 0x168410 diff --git a/drivers/net/bonding/bond_alb.c b/drivers/net/bonding/bond_alb.c index 9b5936f072d..a1e7eb92bbf 100644 --- a/drivers/net/bonding/bond_alb.c +++ b/drivers/net/bonding/bond_alb.c @@ -559,7 +559,7 @@ static void rlb_update_rx_clients(struct bonding *bond) } } - /* do not update the entries again untill this counter is zero so that + /* do not update the entries again until this counter is zero so that * not to confuse the clients. */ bond_info->rlb_update_delay_counter = RLB_UPDATE_DELAY; diff --git a/drivers/net/cxgb3/sge.c b/drivers/net/cxgb3/sge.c index 6366061712f..b8d92c6f3dd 100644 --- a/drivers/net/cxgb3/sge.c +++ b/drivers/net/cxgb3/sge.c @@ -1285,7 +1285,7 @@ netdev_tx_t t3_eth_xmit(struct sk_buff *skb, struct net_device *dev) /* * We do not use Tx completion interrupts to free DMAd Tx packets. - * This is good for performamce but means that we rely on new Tx + * This is good for performance but means that we rely on new Tx * packets arriving to run the destructors of completed packets, * which open up space in their sockets' send queues. Sometimes * we do not get such new packets causing Tx to stall. A single diff --git a/drivers/net/ehea/ehea_ethtool.c b/drivers/net/ehea/ehea_ethtool.c index d7688522336..75b099ce49c 100644 --- a/drivers/net/ehea/ehea_ethtool.c +++ b/drivers/net/ehea/ehea_ethtool.c @@ -118,7 +118,7 @@ doit: ret = ehea_set_portspeed(port, sp); if (!ret) - ehea_info("%s: Port speed succesfully set: %dMbps " + ehea_info("%s: Port speed successfully set: %dMbps " "%s Duplex", port->netdev->name, port->port_speed, port->full_duplex == 1 ? "Full" : "Half"); @@ -134,7 +134,7 @@ static int ehea_nway_reset(struct net_device *dev) ret = ehea_set_portspeed(port, EHEA_SPEED_AUTONEG); if (!ret) - ehea_info("%s: Port speed succesfully set: %dMbps " + ehea_info("%s: Port speed successfully set: %dMbps " "%s Duplex", port->netdev->name, port->port_speed, port->full_duplex == 1 ? "Full" : "Half"); diff --git a/drivers/net/hamradio/baycom_ser_fdx.c b/drivers/net/hamradio/baycom_ser_fdx.c index ed60fd66427..0cab992b3d1 100644 --- a/drivers/net/hamradio/baycom_ser_fdx.c +++ b/drivers/net/hamradio/baycom_ser_fdx.c @@ -35,7 +35,7 @@ * driver only supports standard serial hardware (8250, 16450, 16550A) * * This modem usually draws its supply current out of the otherwise unused - * TXD pin of the serial port. Thus a contignuous stream of 0x00-bytes + * TXD pin of the serial port. Thus a contiguous stream of 0x00-bytes * is transmitted to achieve a positive supply voltage. * * hsk: This is a 4800 baud FSK modem, designed for TNC use. It works fine diff --git a/drivers/net/irda/smsc-ircc2.c b/drivers/net/irda/smsc-ircc2.c index 1e8dd8c74a6..8f7d0d146f2 100644 --- a/drivers/net/irda/smsc-ircc2.c +++ b/drivers/net/irda/smsc-ircc2.c @@ -115,7 +115,7 @@ struct smsc_ircc_subsystem_configuration { unsigned short vendor; /* PCI vendor ID */ unsigned short device; /* PCI vendor ID */ unsigned short subvendor; /* PCI subsystem vendor ID */ - unsigned short subdevice; /* PCI sybsystem device ID */ + unsigned short subdevice; /* PCI subsystem device ID */ unsigned short sir_io; /* I/O port for SIR */ unsigned short fir_io; /* I/O port for FIR */ unsigned char fir_irq; /* FIR IRQ */ diff --git a/drivers/net/iseries_veth.c b/drivers/net/iseries_veth.c index aa7286bc436..8739ba850f8 100644 --- a/drivers/net/iseries_veth.c +++ b/drivers/net/iseries_veth.c @@ -1384,7 +1384,7 @@ static inline void veth_build_dma_list(struct dma_chunk *list, unsigned long done; int i = 1; - /* FIXME: skbs are continguous in real addresses. Do we + /* FIXME: skbs are contiguous in real addresses. Do we * really need to break it into PAGE_SIZE chunks, or can we do * it just at the granularity of iSeries real->absolute * mapping? Indeed, given the way the allocator works, can we diff --git a/drivers/net/lasi_82596.c b/drivers/net/lasi_82596.c index a0c578585a5..b77238dbafb 100644 --- a/drivers/net/lasi_82596.c +++ b/drivers/net/lasi_82596.c @@ -47,7 +47,7 @@ TBD: * look at deferring rx frames rather than discarding (as per tulip) * handle tx ring full as per tulip - * performace test to tune rx_copybreak + * performance test to tune rx_copybreak Most of my modifications relate to the braindead big-endian implementation by Intel. When the i596 is operating in diff --git a/drivers/net/lib82596.c b/drivers/net/lib82596.c index 51e11c3e53e..c0dbfc185b5 100644 --- a/drivers/net/lib82596.c +++ b/drivers/net/lib82596.c @@ -47,7 +47,7 @@ TBD: * look at deferring rx frames rather than discarding (as per tulip) * handle tx ring full as per tulip - * performace test to tune rx_copybreak + * performance test to tune rx_copybreak Most of my modifications relate to the braindead big-endian implementation by Intel. When the i596 is operating in diff --git a/drivers/net/mlx4/en_rx.c b/drivers/net/mlx4/en_rx.c index 03b781a7a18..829b9ec9ff6 100644 --- a/drivers/net/mlx4/en_rx.c +++ b/drivers/net/mlx4/en_rx.c @@ -204,7 +204,7 @@ static void mlx4_en_free_rx_desc(struct mlx4_en_priv *priv, en_dbg(DRV, priv, "Freeing fragment:%d\n", nr); dma = be64_to_cpu(rx_desc->data[nr].addr); - en_dbg(DRV, priv, "Unmaping buffer at dma:0x%llx\n", (u64) dma); + en_dbg(DRV, priv, "Unmapping buffer at dma:0x%llx\n", (u64) dma); pci_unmap_single(mdev->pdev, dma, skb_frags[nr].size, PCI_DMA_FROMDEVICE); put_page(skb_frags[nr].page); diff --git a/drivers/net/mlx4/en_tx.c b/drivers/net/mlx4/en_tx.c index 8c7279965b4..3d1396af946 100644 --- a/drivers/net/mlx4/en_tx.c +++ b/drivers/net/mlx4/en_tx.c @@ -47,7 +47,7 @@ enum { static int inline_thold __read_mostly = MAX_INLINE; module_param_named(inline_thold, inline_thold, int, 0444); -MODULE_PARM_DESC(inline_thold, "treshold for using inline data"); +MODULE_PARM_DESC(inline_thold, "threshold for using inline data"); int mlx4_en_create_tx_ring(struct mlx4_en_priv *priv, struct mlx4_en_tx_ring *ring, u32 size, diff --git a/drivers/net/mlx4/mlx4_en.h b/drivers/net/mlx4/mlx4_en.h index 4376147b0ea..82c3ebc584e 100644 --- a/drivers/net/mlx4/mlx4_en.h +++ b/drivers/net/mlx4/mlx4_en.h @@ -162,7 +162,7 @@ enum { #define MLX4_EN_DEF_RX_PAUSE 1 #define MLX4_EN_DEF_TX_PAUSE 1 -/* Interval between sucessive polls in the Tx routine when polling is used +/* Interval between successive polls in the Tx routine when polling is used instead of interrupts (in per-core Tx rings) - should be power of 2 */ #define MLX4_EN_TX_POLL_MODER 16 #define MLX4_EN_TX_POLL_TIMEOUT (HZ / 4) diff --git a/drivers/net/ps3_gelic_net.c b/drivers/net/ps3_gelic_net.c index b211613e9db..86fde1a90a5 100644 --- a/drivers/net/ps3_gelic_net.c +++ b/drivers/net/ps3_gelic_net.c @@ -296,7 +296,7 @@ static void gelic_card_reset_chain(struct gelic_card *card, * @card: card structure * @descr: descriptor to re-init * - * return 0 on succes, <0 on failure + * return 0 on success, <0 on failure * * allocates a new rx skb, iommu-maps it and attaches it to the descriptor. * Activate the descriptor state-wise diff --git a/drivers/net/ps3_gelic_wireless.h b/drivers/net/ps3_gelic_wireless.h index 5b631c6c977..0a88b535197 100644 --- a/drivers/net/ps3_gelic_wireless.h +++ b/drivers/net/ps3_gelic_wireless.h @@ -199,7 +199,7 @@ struct gelic_eurus_rssi_info { /* for 'stat' member of gelic_wl_info */ enum gelic_wl_info_status_bit { GELIC_WL_STAT_CONFIGURED, - GELIC_WL_STAT_CH_INFO, /* ch info aquired */ + GELIC_WL_STAT_CH_INFO, /* ch info acquired */ GELIC_WL_STAT_ESSID_SET, /* ESSID specified by userspace */ GELIC_WL_STAT_BSSID_SET, /* BSSID specified by userspace */ GELIC_WL_STAT_WPA_PSK_SET, /* PMK specified by userspace */ diff --git a/drivers/net/qla3xxx.c b/drivers/net/qla3xxx.c index 4c610511eb4..f72643313ba 100644 --- a/drivers/net/qla3xxx.c +++ b/drivers/net/qla3xxx.c @@ -3651,7 +3651,7 @@ static int ql_adapter_up(struct ql3_adapter *qdev) ql_sem_unlock(qdev, QL_DRVR_SEM_MASK); } else { printk(KERN_ERR PFX - "%s: Could not aquire driver lock.\n", + "%s: Could not acquire driver lock.\n", ndev->name); goto err_lock; } diff --git a/drivers/net/s2io.c b/drivers/net/s2io.c index 0dd7839322b..cc4218667cb 100644 --- a/drivers/net/s2io.c +++ b/drivers/net/s2io.c @@ -3238,7 +3238,7 @@ static u64 s2io_mdio_read(u32 mmd_type, u64 addr, struct net_device *dev) /** * s2io_chk_xpak_counter - Function to check the status of the xpak counters - * @counter : couter value to be updated + * @counter : counter value to be updated * @flag : flag to indicate the status * @type : counter type * Description: diff --git a/drivers/net/sis900.c b/drivers/net/sis900.c index c072f7f36ac..9d94a141555 100644 --- a/drivers/net/sis900.c +++ b/drivers/net/sis900.c @@ -1760,7 +1760,7 @@ static int sis900_rx(struct net_device *net_dev) sis_priv->rx_ring[entry].bufptr, RX_BUF_SIZE, PCI_DMA_FROMDEVICE); - /* refill the Rx buffer, what if there is not enought + /* refill the Rx buffer, what if there is not enough * memory for new socket buffer ?? */ if ((skb = dev_alloc_skb(RX_BUF_SIZE)) == NULL) { /* @@ -1775,7 +1775,7 @@ static int sis900_rx(struct net_device *net_dev) } /* This situation should never happen, but due to - some unknow bugs, it is possible that + some unknown bugs, it is possible that we are working on NULL sk_buff :-( */ if (sis_priv->rx_skbuff[entry] == NULL) { if (netif_msg_rx_err(sis_priv)) diff --git a/drivers/net/skfp/h/smc.h b/drivers/net/skfp/h/smc.h index 1758d954836..026a83b9f74 100644 --- a/drivers/net/skfp/h/smc.h +++ b/drivers/net/skfp/h/smc.h @@ -393,10 +393,10 @@ struct smt_config { */ u_long mac_d_max ; /* MAC : D_Max timer value */ - u_long lct_short ; /* LCT : error threshhold */ - u_long lct_medium ; /* LCT : error threshhold */ - u_long lct_long ; /* LCT : error threshhold */ - u_long lct_extended ; /* LCT : error threshhold */ + u_long lct_short ; /* LCT : error threshold */ + u_long lct_medium ; /* LCT : error threshold */ + u_long lct_long ; /* LCT : error threshold */ + u_long lct_extended ; /* LCT : error threshold */ } ; #ifdef DEBUG diff --git a/drivers/net/skfp/skfddi.c b/drivers/net/skfp/skfddi.c index b27156eaf26..db216a72850 100644 --- a/drivers/net/skfp/skfddi.c +++ b/drivers/net/skfp/skfddi.c @@ -1002,7 +1002,7 @@ static int skfp_ioctl(struct net_device *dev, struct ifreq *rq, int cmd) } break; default: - printk("ioctl for %s: unknow cmd: %04x\n", dev->name, ioc.cmd); + printk("ioctl for %s: unknown cmd: %04x\n", dev->name, ioc.cmd); status = -EOPNOTSUPP; } // switch diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c index 6a10d7ba587..a76cd66c228 100644 --- a/drivers/net/sky2.c +++ b/drivers/net/sky2.c @@ -1975,7 +1975,7 @@ static void sky2_link_down(struct sky2_port *sky2) netif_carrier_off(sky2->netdev); - /* Turn on link LED */ + /* Turn off link LED */ sky2_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_OFF); if (netif_msg_link(sky2)) diff --git a/drivers/net/smsc911x.c b/drivers/net/smsc911x.c index f9cdcbcb77d..24954fecf3d 100644 --- a/drivers/net/smsc911x.c +++ b/drivers/net/smsc911x.c @@ -816,7 +816,7 @@ static int smsc911x_mii_probe(struct net_device *dev) SMSC_TRACE(HW, "Passed Loop Back Test"); #endif /* USE_PHY_WORK_AROUND */ - SMSC_TRACE(HW, "phy initialised succesfully"); + SMSC_TRACE(HW, "phy initialised successfully"); return 0; } diff --git a/drivers/net/smsc911x.h b/drivers/net/smsc911x.h index b5716bd8a59..016360c65ce 100644 --- a/drivers/net/smsc911x.h +++ b/drivers/net/smsc911x.h @@ -30,7 +30,7 @@ #define SMSC_NAPI_WEIGHT 16 /* implements a PHY loopback test at initialisation time, to ensure a packet - * can be succesfully looped back */ + * can be successfully looped back */ #define USE_PHY_WORK_AROUND #define DPRINTK(nlevel, klevel, fmt, args...) \ diff --git a/drivers/net/spider_net.c b/drivers/net/spider_net.c index 90e663f4515..40b51e6bc77 100644 --- a/drivers/net/spider_net.c +++ b/drivers/net/spider_net.c @@ -409,7 +409,7 @@ spider_net_free_rx_chain_contents(struct spider_net_card *card) * @card: card structure * @descr: descriptor to re-init * - * Return 0 on succes, <0 on failure. + * Return 0 on success, <0 on failure. * * Allocates a new rx skb, iommu-maps it and attaches it to the * descriptor. Mark the descriptor as activated, ready-to-use. diff --git a/drivers/net/stmmac/gmac.c b/drivers/net/stmmac/gmac.c index b624bb5bae0..52586ee6895 100644 --- a/drivers/net/stmmac/gmac.c +++ b/drivers/net/stmmac/gmac.c @@ -112,7 +112,7 @@ static void gmac_dma_operation_mode(unsigned long ioaddr, int txmode, " (threshold = %d)\n", txmode); csr6 &= ~DMA_CONTROL_TSF; csr6 &= DMA_CONTROL_TC_TX_MASK; - /* Set the transmit threashold */ + /* Set the transmit threshold */ if (txmode <= 32) csr6 |= DMA_CONTROL_TTC_32; else if (txmode <= 64) diff --git a/drivers/net/stmmac/gmac.h b/drivers/net/stmmac/gmac.h index 684a363120a..2e82d6c9a14 100644 --- a/drivers/net/stmmac/gmac.h +++ b/drivers/net/stmmac/gmac.h @@ -154,14 +154,14 @@ enum rx_tx_priority_ratio { #define DMA_CONTROL_DT 0x04000000 /* Disable Drop TCP/IP csum error */ #define DMA_CONTROL_RSF 0x02000000 /* Receive Store and Forward */ #define DMA_CONTROL_DFF 0x01000000 /* Disaable flushing */ -/* Theshold for Activating the FC */ +/* Threshold for Activating the FC */ enum rfa { act_full_minus_1 = 0x00800000, act_full_minus_2 = 0x00800200, act_full_minus_3 = 0x00800400, act_full_minus_4 = 0x00800600, }; -/* Theshold for Deactivating the FC */ +/* Threshold for Deactivating the FC */ enum rfd { deac_full_minus_1 = 0x00400000, deac_full_minus_2 = 0x00400800, diff --git a/drivers/net/tokenring/ibmtr.c b/drivers/net/tokenring/ibmtr.c index 75fa32e34fd..685cc3a4d2a 100644 --- a/drivers/net/tokenring/ibmtr.c +++ b/drivers/net/tokenring/ibmtr.c @@ -96,7 +96,7 @@ * * Change by Mike Sullivan et al.: * + added turbo card support. No need to use lanaid to configure - * the adapter into isa compatiblity mode. + * the adapter into isa compatibility mode. * * Changes by Burt Silverman to allow the computer to behave nicely when * a cable is pulled or not in place, or a PCMCIA card is removed hot. diff --git a/drivers/net/tokenring/smctr.c b/drivers/net/tokenring/smctr.c index ebda61bc4c2..78e12b5e3ac 100644 --- a/drivers/net/tokenring/smctr.c +++ b/drivers/net/tokenring/smctr.c @@ -426,7 +426,7 @@ static int smctr_alloc_shared_memory(struct net_device *dev) smctr_malloc(dev, 1L); /* Allocate Non-MAC receive data buffers. - * To guarantee a minimum of 256 contigous memory to + * To guarantee a minimum of 256 contiguous memory to * UM_Receive_Packet's lookahead pointer, before a page * change or ring end is encountered, place each rx buffer on * a 256 byte boundary. diff --git a/drivers/net/ucc_geth.c b/drivers/net/ucc_geth.c index 4469f2451a6..5e9adbaf674 100644 --- a/drivers/net/ucc_geth.c +++ b/drivers/net/ucc_geth.c @@ -3798,7 +3798,7 @@ static int ucc_geth_probe(struct of_device* ofdev, const struct of_device_id *ma prop = of_get_property(np, "tx-clock", NULL); if (!prop) { printk(KERN_ERR - "ucc_geth: mising tx-clock-name property\n"); + "ucc_geth: missing tx-clock-name property\n"); return -EINVAL; } if ((*prop < QE_CLK_NONE) || (*prop > QE_CLK24)) { diff --git a/drivers/net/ucc_geth.h b/drivers/net/ucc_geth.h index 03a6ca016d5..a007e2acf65 100644 --- a/drivers/net/ucc_geth.h +++ b/drivers/net/ucc_geth.h @@ -80,16 +80,16 @@ struct ucc_geth { frames) received that were between 128 (Including FCS length==4) and 255 octets */ u32 txok; /* Total number of octets residing in frames - that where involved in succesfull + that where involved in successfull transmission */ u16 txcf; /* Total number of PAUSE control frames transmitted by this MAC */ u8 res4[0x2]; u32 tmca; /* Total number of frames that were transmitted - succesfully with the group address bit set + successfully with the group address bit set that are not broadcast frames */ u32 tbca; /* Total number of frames transmitted - succesfully that had destination address + successfully that had destination address field equal to the broadcast address */ u32 rxfok; /* Total number of frames received OK */ u32 rxbok; /* Total number of octets received OK */ @@ -98,9 +98,9 @@ struct ucc_geth { HW because it includes octets in frames that never even reach the UCC */ u32 rmca; /* Total number of frames that were received - succesfully with the group address bit set + successfully with the group address bit set that are not broadcast frames */ - u32 rbca; /* Total number of frames received succesfully + u32 rbca; /* Total number of frames received successfully that had destination address equal to the broadcast address */ u32 scar; /* Statistics carry register */ @@ -759,15 +759,15 @@ struct ucc_geth_hardware_statistics { frames) received that were between 128 (Including FCS length==4) and 255 octets */ u32 txok; /* Total number of octets residing in frames - that where involved in succesfull + that where involved in successfull transmission */ u16 txcf; /* Total number of PAUSE control frames transmitted by this MAC */ u32 tmca; /* Total number of frames that were transmitted - succesfully with the group address bit set + successfully with the group address bit set that are not broadcast frames */ u32 tbca; /* Total number of frames transmitted - succesfully that had destination address + successfully that had destination address field equal to the broadcast address */ u32 rxfok; /* Total number of frames received OK */ u32 rxbok; /* Total number of octets received OK */ @@ -776,9 +776,9 @@ struct ucc_geth_hardware_statistics { HW because it includes octets in frames that never even reach the UCC */ u32 rmca; /* Total number of frames that were received - succesfully with the group address bit set + successfully with the group address bit set that are not broadcast frames */ - u32 rbca; /* Total number of frames received succesfully + u32 rbca; /* Total number of frames received successfully that had destination address equal to the broadcast address */ } __attribute__ ((packed)); diff --git a/drivers/net/usb/smsc95xx.c b/drivers/net/usb/smsc95xx.c index c6c922247d0..0c3c738d741 100644 --- a/drivers/net/usb/smsc95xx.c +++ b/drivers/net/usb/smsc95xx.c @@ -748,7 +748,7 @@ static int smsc95xx_phy_initialize(struct usbnet *dev) mii_nway_restart(&dev->mii); if (netif_msg_ifup(dev)) - devdbg(dev, "phy initialised succesfully"); + devdbg(dev, "phy initialised successfully"); return 0; } diff --git a/drivers/net/wan/hdlc_fr.c b/drivers/net/wan/hdlc_fr.c index 840cff72a0f..4d4c543c146 100644 --- a/drivers/net/wan/hdlc_fr.c +++ b/drivers/net/wan/hdlc_fr.c @@ -182,7 +182,7 @@ static inline pvc_device* find_pvc(hdlc_device *hdlc, u16 dlci) if (pvc->dlci == dlci) return pvc; if (pvc->dlci > dlci) - return NULL; /* the listed is sorted */ + return NULL; /* the list is sorted */ pvc = pvc->next; } diff --git a/drivers/net/wan/lmc/lmc_main.c b/drivers/net/wan/lmc/lmc_main.c index 7ea71b33d2e..ee784e091f6 100644 --- a/drivers/net/wan/lmc/lmc_main.c +++ b/drivers/net/wan/lmc/lmc_main.c @@ -927,7 +927,7 @@ static int __devinit lmc_init_one(struct pci_dev *pdev, sc->lmc_media = &lmc_t1_media; break; default: - printk(KERN_WARNING "%s: LMC UNKOWN CARD!\n", dev->name); + printk(KERN_WARNING "%s: LMC UNKNOWN CARD!\n", dev->name); break; } diff --git a/drivers/net/wimax/i2400m/rx.c b/drivers/net/wimax/i2400m/rx.c index 07c32e68909..99d27473ba3 100644 --- a/drivers/net/wimax/i2400m/rx.c +++ b/drivers/net/wimax/i2400m/rx.c @@ -1114,7 +1114,7 @@ error: * device. See the file header for the format. Run all checks on the * buffer header, then run over each payload's descriptors, verify * their consistency and act on each payload's contents. If - * everything is succesful, update the device's statistics. + * everything is successful, update the device's statistics. * * Note: You need to set the skb to contain only the length of the * received buffer; for that, use skb_trim(skb, RECEIVED_SIZE). diff --git a/drivers/net/wireless/ath/ath5k/base.h b/drivers/net/wireless/ath/ath5k/base.h index a28c42f32c9..4da02941046 100644 --- a/drivers/net/wireless/ath/ath5k/base.h +++ b/drivers/net/wireless/ath/ath5k/base.h @@ -36,7 +36,7 @@ */ /* - * Defintions for the Atheros Wireless LAN controller driver. + * Definitions for the Atheros Wireless LAN controller driver. */ #ifndef _DEV_ATH_ATHVAR_H #define _DEV_ATH_ATHVAR_H @@ -193,7 +193,7 @@ struct ath5k_softc { struct ath5k_txq *cabq; /* content after beacon */ int power_level; /* Requested tx power in dbm */ - bool assoc; /* assocate state */ + bool assoc; /* associate state */ bool enable_beacon; /* true if beacons are on */ }; diff --git a/drivers/net/wireless/ath/ath5k/eeprom.c b/drivers/net/wireless/ath/ath5k/eeprom.c index 644962adda9..81ea52c4faf 100644 --- a/drivers/net/wireless/ath/ath5k/eeprom.c +++ b/drivers/net/wireless/ath/ath5k/eeprom.c @@ -1492,7 +1492,7 @@ ath5k_eeprom_read_target_rate_pwr_info(struct ath5k_hw *ah, unsigned int mode) * This info is used to calibrate the baseband power table. Imagine * that for each channel there is a power curve that's hw specific * (depends on amplifier etc) and we try to "correct" this curve using - * offests we pass on to phy chip (baseband -> before amplifier) so that + * offsets we pass on to phy chip (baseband -> before amplifier) so that * it can use accurate power values when setting tx power (takes amplifier's * performance on each channel into account). * diff --git a/drivers/net/wireless/ath/ath5k/phy.c b/drivers/net/wireless/ath/ath5k/phy.c index 1a039f2bd73..6f04cc758dc 100644 --- a/drivers/net/wireless/ath/ath5k/phy.c +++ b/drivers/net/wireless/ath/ath5k/phy.c @@ -117,7 +117,7 @@ static unsigned int ath5k_hw_rfb_op(struct ath5k_hw *ah, /* * This code is used to optimize rf gain on different environments - * (temprature mostly) based on feedback from a power detector. + * (temperature mostly) based on feedback from a power detector. * * It's only used on RF5111 and RF5112, later RF chips seem to have * auto adjustment on hw -notice they have a much smaller BANK 7 and @@ -2675,7 +2675,7 @@ ath5k_setup_channel_powertable(struct ath5k_hw *ah, /* Fill curves in reverse order * from lower power (max gain) * to higher power. Use curve -> idx - * backmaping we did on eeprom init */ + * backmapping we did on eeprom init */ u8 idx = pdg_curve_to_idx[pdg]; /* Grab the needed curves by index */ @@ -2777,7 +2777,7 @@ ath5k_setup_channel_powertable(struct ath5k_hw *ah, /* Now we have a set of curves for this * channel on tmpL (x range is table_max - table_min * and y values are tmpL[pdg][]) sorted in the same - * order as EEPROM (because we've used the backmaping). + * order as EEPROM (because we've used the backmapping). * So for RF5112 it's from higher power to lower power * and for RF2413 it's from lower power to higher power. * For RF5111 we only have one curve. */ diff --git a/drivers/net/wireless/ath/ath9k/rc.c b/drivers/net/wireless/ath/ath9k/rc.c index 1895d63aad0..0a35ee62a02 100644 --- a/drivers/net/wireless/ath/ath9k/rc.c +++ b/drivers/net/wireless/ath/ath9k/rc.c @@ -969,7 +969,7 @@ static bool ath_rc_update_per(struct ath_softc *sc, * Since this probe succeeded, we allow the next * probe twice as soon. This allows the maxRate * to move up faster if the probes are - * succesful. + * successful. */ ath_rc_priv->probe_time = now_msec - rate_table->probe_interval / 2; diff --git a/drivers/net/wireless/b43/main.c b/drivers/net/wireless/b43/main.c index 098dda1a67c..e56b941ecaa 100644 --- a/drivers/net/wireless/b43/main.c +++ b/drivers/net/wireless/b43/main.c @@ -2955,7 +2955,7 @@ static void do_periodic_work(struct b43_wldev *dev) /* Periodic work locking policy: * The whole periodic work handler is protected by * wl->mutex. If another lock is needed somewhere in the - * pwork callchain, it's aquired in-place, where it's needed. + * pwork callchain, it's acquired in-place, where it's needed. */ static void b43_periodic_work_handler(struct work_struct *work) { diff --git a/drivers/net/wireless/b43legacy/main.c b/drivers/net/wireless/b43legacy/main.c index 4b60148a5e6..881784b18b0 100644 --- a/drivers/net/wireless/b43legacy/main.c +++ b/drivers/net/wireless/b43legacy/main.c @@ -2277,7 +2277,7 @@ static void do_periodic_work(struct b43legacy_wldev *dev) /* Periodic work locking policy: * The whole periodic work handler is protected by * wl->mutex. If another lock is needed somewhere in the - * pwork callchain, it's aquired in-place, where it's needed. + * pwork callchain, it's acquired in-place, where it's needed. */ static void b43legacy_periodic_work_handler(struct work_struct *work) { diff --git a/drivers/net/wireless/ipw2x00/ipw2100.c b/drivers/net/wireless/ipw2x00/ipw2100.c index 6e2fc0cb6f8..64af9080fe9 100644 --- a/drivers/net/wireless/ipw2x00/ipw2100.c +++ b/drivers/net/wireless/ipw2x00/ipw2100.c @@ -551,7 +551,7 @@ static int ipw2100_get_ordinal(struct ipw2100_priv *priv, u32 ord, /* get number of entries */ field_count = *(((u16 *) & field_info) + 1); - /* abort if no enought memory */ + /* abort if no enough memory */ total_length = field_len * field_count; if (total_length > *len) { *len = total_length; @@ -3044,7 +3044,7 @@ static void ipw2100_tx_send_data(struct ipw2100_priv *priv) IPW_MAX_BDS)) { /* TODO: Support merging buffers if more than * IPW_MAX_BDS are used */ - IPW_DEBUG_INFO("%s: Maximum BD theshold exceeded. " + IPW_DEBUG_INFO("%s: Maximum BD threshold exceeded. " "Increase fragmentation level.\n", priv->net_dev->name); } @@ -6820,7 +6820,7 @@ static int ipw2100_wx_get_range(struct net_device *dev, range->max_qual.updated = 7; /* Updated all three */ range->avg_qual.qual = 70; /* > 8% missed beacons is 'bad' */ - /* TODO: Find real 'good' to 'bad' threshol value for RSSI */ + /* TODO: Find real 'good' to 'bad' threshold value for RSSI */ range->avg_qual.level = 20 + IPW2100_RSSI_TO_DBM; range->avg_qual.noise = 0; range->avg_qual.updated = 7; /* Updated all three */ diff --git a/drivers/net/wireless/ipw2x00/ipw2200.c b/drivers/net/wireless/ipw2x00/ipw2200.c index a6ca536e44f..fdbc97b7fcb 100644 --- a/drivers/net/wireless/ipw2x00/ipw2200.c +++ b/drivers/net/wireless/ipw2x00/ipw2200.c @@ -768,7 +768,7 @@ static int ipw_get_ordinal(struct ipw_priv *priv, u32 ord, void *val, u32 * len) /* get number of entries */ field_count = *(((u16 *) & field_info) + 1); - /* abort if not enought memory */ + /* abort if not enough memory */ total_len = field_len * field_count; if (total_len > *len) { *len = total_len; @@ -7732,7 +7732,7 @@ static void ipw_rebuild_decrypted_skb(struct ipw_priv *priv, case SEC_LEVEL_0: break; default: - printk(KERN_ERR "Unknow security level %d\n", + printk(KERN_ERR "Unknown security level %d\n", priv->ieee->sec.level); break; } @@ -8916,7 +8916,7 @@ static int ipw_wx_get_range(struct net_device *dev, range->max_qual.updated = 7; /* Updated all three */ range->avg_qual.qual = 70; - /* TODO: Find real 'good' to 'bad' threshol value for RSSI */ + /* TODO: Find real 'good' to 'bad' threshold value for RSSI */ range->avg_qual.level = 0; /* FIXME to real average level */ range->avg_qual.noise = 0; range->avg_qual.updated = 7; /* Updated all three */ @@ -10289,7 +10289,7 @@ static int ipw_tx_skb(struct ipw_priv *priv, struct libipw_txb *txb, case SEC_LEVEL_0: break; default: - printk(KERN_ERR "Unknow security level %d\n", + printk(KERN_ERR "Unknown security level %d\n", priv->ieee->sec.level); break; } diff --git a/drivers/net/wireless/ipw2x00/libipw_module.c b/drivers/net/wireless/ipw2x00/libipw_module.c index eb2b60834c1..c7b3f17d8da 100644 --- a/drivers/net/wireless/ipw2x00/libipw_module.c +++ b/drivers/net/wireless/ipw2x00/libipw_module.c @@ -175,7 +175,7 @@ struct net_device *alloc_ieee80211(int sizeof_priv) ieee->host_decrypt = 1; ieee->host_mc_decrypt = 1; - /* Host fragementation in Open mode. Default is enabled. + /* Host fragmentation in Open mode. Default is enabled. * Note: host fragmentation is always enabled if host encryption * is enabled. For cards can do hardware encryption, they must do * hardware fragmentation as well. So we don't need a variable diff --git a/drivers/net/wireless/iwmc3200wifi/hal.c b/drivers/net/wireless/iwmc3200wifi/hal.c index c430418248b..d13c8853ee8 100644 --- a/drivers/net/wireless/iwmc3200wifi/hal.c +++ b/drivers/net/wireless/iwmc3200wifi/hal.c @@ -411,7 +411,7 @@ static void iwm_build_lmac_hdr(struct iwm_priv *iwm, struct iwm_lmac_hdr *hdr, /* * iwm_hal_send_host_cmd(): sends commands to the UMAC or the LMAC. * Sending command to the LMAC is equivalent to sending a - * regular UMAC command with the LMAC passtrough or the LMAC + * regular UMAC command with the LMAC passthrough or the LMAC * wrapper UMAC command IDs. */ int iwm_hal_send_host_cmd(struct iwm_priv *iwm, diff --git a/drivers/net/wireless/iwmc3200wifi/rx.c b/drivers/net/wireless/iwmc3200wifi/rx.c index 771a301003c..8ddb51a2a97 100644 --- a/drivers/net/wireless/iwmc3200wifi/rx.c +++ b/drivers/net/wireless/iwmc3200wifi/rx.c @@ -1448,7 +1448,7 @@ static void iwm_rx_process_packet(struct iwm_priv *iwm, kfree_skb(packet->skb); break; default: - IWM_ERR(iwm, "Unknow ticket action: %d\n", + IWM_ERR(iwm, "Unknown ticket action: %d\n", le16_to_cpu(ticket_node->ticket->action)); kfree_skb(packet->skb); } diff --git a/drivers/net/wireless/libertas/if_sdio.c b/drivers/net/wireless/libertas/if_sdio.c index 485a8d40652..afe6abecc04 100644 --- a/drivers/net/wireless/libertas/if_sdio.c +++ b/drivers/net/wireless/libertas/if_sdio.c @@ -934,7 +934,7 @@ static int if_sdio_probe(struct sdio_func *func, } if (i == ARRAY_SIZE(if_sdio_models)) { - lbs_pr_err("unkown card model 0x%x\n", card->model); + lbs_pr_err("unknown card model 0x%x\n", card->model); ret = -ENODEV; goto free; } diff --git a/drivers/net/wireless/orinoco/hermes_dld.c b/drivers/net/wireless/orinoco/hermes_dld.c index a3eefe109df..84200da900b 100644 --- a/drivers/net/wireless/orinoco/hermes_dld.c +++ b/drivers/net/wireless/orinoco/hermes_dld.c @@ -550,7 +550,7 @@ static const struct { \ #define DEFAULT_PDR(pid) default_pdr_data_##pid -/* HWIF Compatiblity */ +/* HWIF Compatibility */ DEFINE_DEFAULT_PDR(0x0005, 10, "\x00\x00\x06\x00\x01\x00\x01\x00\x01\x00"); /* PPPPSign */ @@ -656,7 +656,7 @@ int hermes_apply_pda_with_defaults(hermes_t *hw, record_id + 1, pdi); } break; - case 0x5: /* HWIF Compatiblity */ + case 0x5: /* HWIF Compatibility */ default_pdi = (struct pdi *) &DEFAULT_PDR(0x0005); break; case 0x108: /* PPPPSign */ diff --git a/drivers/net/wireless/prism54/isl_ioctl.c b/drivers/net/wireless/prism54/isl_ioctl.c index bc08464d832..f7f5c793514 100644 --- a/drivers/net/wireless/prism54/isl_ioctl.c +++ b/drivers/net/wireless/prism54/isl_ioctl.c @@ -1897,7 +1897,7 @@ prism54_get_mac(struct net_device *ndev, struct iw_request_info *info, return 0; } -/* Setting policy also clears the MAC acl, even if we don't change the defaut +/* Setting policy also clears the MAC acl, even if we don't change the default * policy */ @@ -2323,7 +2323,7 @@ prism54_process_trap_helper(islpci_private *priv, enum oid_num_t oid, case DOT11_OID_BEACON: send_formatted_event(priv, - "Received a beacon from an unkown AP", + "Received a beacon from an unknown AP", mlme, 0); break; diff --git a/drivers/net/wireless/rt2x00/rt2400pci.h b/drivers/net/wireless/rt2x00/rt2400pci.h index ccd644104ad..aced0577569 100644 --- a/drivers/net/wireless/rt2x00/rt2400pci.h +++ b/drivers/net/wireless/rt2x00/rt2400pci.h @@ -35,7 +35,7 @@ /* * Signal information. - * Defaul offset is required for RSSI <-> dBm conversion. + * Default offset is required for RSSI <-> dBm conversion. */ #define DEFAULT_RSSI_OFFSET 100 diff --git a/drivers/net/wireless/rt2x00/rt2500pci.h b/drivers/net/wireless/rt2x00/rt2500pci.h index 54d37957883..3db9041838a 100644 --- a/drivers/net/wireless/rt2x00/rt2500pci.h +++ b/drivers/net/wireless/rt2x00/rt2500pci.h @@ -46,7 +46,7 @@ /* * Signal information. - * Defaul offset is required for RSSI <-> dBm conversion. + * Default offset is required for RSSI <-> dBm conversion. */ #define DEFAULT_RSSI_OFFSET 121 diff --git a/drivers/net/wireless/rt2x00/rt2500usb.h b/drivers/net/wireless/rt2x00/rt2500usb.h index b01edca4258..d3000827883 100644 --- a/drivers/net/wireless/rt2x00/rt2500usb.h +++ b/drivers/net/wireless/rt2x00/rt2500usb.h @@ -46,7 +46,7 @@ /* * Signal information. - * Defaul offset is required for RSSI <-> dBm conversion. + * Default offset is required for RSSI <-> dBm conversion. */ #define DEFAULT_RSSI_OFFSET 120 diff --git a/drivers/net/wireless/rt2x00/rt61pci.h b/drivers/net/wireless/rt2x00/rt61pci.h index 93eb699165c..77b5116f549 100644 --- a/drivers/net/wireless/rt2x00/rt61pci.h +++ b/drivers/net/wireless/rt2x00/rt61pci.h @@ -37,7 +37,7 @@ /* * Signal information. - * Defaul offset is required for RSSI <-> dBm conversion. + * Default offset is required for RSSI <-> dBm conversion. */ #define DEFAULT_RSSI_OFFSET 120 diff --git a/drivers/net/wireless/rt2x00/rt73usb.h b/drivers/net/wireless/rt2x00/rt73usb.h index 81fe0be51c4..e194332dac5 100644 --- a/drivers/net/wireless/rt2x00/rt73usb.h +++ b/drivers/net/wireless/rt2x00/rt73usb.h @@ -37,7 +37,7 @@ /* * Signal information. - * Defaul offset is required for RSSI <-> dBm conversion. + * Default offset is required for RSSI <-> dBm conversion. */ #define DEFAULT_RSSI_OFFSET 120 diff --git a/drivers/net/wireless/wavelan_cs.c b/drivers/net/wireless/wavelan_cs.c index 33918fd5b23..10c702b5be4 100644 --- a/drivers/net/wireless/wavelan_cs.c +++ b/drivers/net/wireless/wavelan_cs.c @@ -3987,7 +3987,7 @@ wavelan_interrupt(int irq, #endif /* Prevent reentrancy. We need to do that because we may have - * multiple interrupt handler running concurently. + * multiple interrupt handler running concurrently. * It is safe because interrupts are disabled before aquiring * the spinlock. */ spin_lock(&lp->spinlock); diff --git a/drivers/net/wireless/zd1211rw/zd_mac.c b/drivers/net/wireless/zd1211rw/zd_mac.c index 6d666359a42..2b7f9659437 100644 --- a/drivers/net/wireless/zd1211rw/zd_mac.c +++ b/drivers/net/wireless/zd1211rw/zd_mac.c @@ -312,7 +312,7 @@ static void tx_status(struct ieee80211_hw *hw, struct sk_buff *skb, * zd_mac_tx_failed - callback for failed frames * @dev: the mac80211 wireless device * - * This function is called if a frame couldn't be succesfully be + * This function is called if a frame couldn't be successfully be * transferred. The first frame from the tx queue, will be selected and * reported as error to the upper layers. */ |