diff options
Diffstat (limited to 'drivers/net/wireless/wl12xx/boot.c')
| -rw-r--r-- | drivers/net/wireless/wl12xx/boot.c | 295 |
1 files changed, 0 insertions, 295 deletions
diff --git a/drivers/net/wireless/wl12xx/boot.c b/drivers/net/wireless/wl12xx/boot.c deleted file mode 100644 index 48ac08c429b..00000000000 --- a/drivers/net/wireless/wl12xx/boot.c +++ /dev/null @@ -1,295 +0,0 @@ -/* - * This file is part of wl12xx - * - * Copyright (C) 2008 Nokia Corporation - * - * Contact: Kalle Valo <kalle.valo@nokia.com> - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * version 2 as published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, but - * WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU - * General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA - * 02110-1301 USA - * - */ - -#include <linux/gpio.h> - -#include "reg.h" -#include "boot.h" -#include "spi.h" -#include "event.h" - -static void wl12xx_boot_enable_interrupts(struct wl12xx *wl) -{ - enable_irq(wl->irq); -} - -void wl12xx_boot_target_enable_interrupts(struct wl12xx *wl) -{ - wl12xx_reg_write32(wl, ACX_REG_INTERRUPT_MASK, ~(wl->intr_mask)); - wl12xx_reg_write32(wl, HI_CFG, HI_CFG_DEF_VAL); -} - -int wl12xx_boot_soft_reset(struct wl12xx *wl) -{ - unsigned long timeout; - u32 boot_data; - - /* perform soft reset */ - wl12xx_reg_write32(wl, ACX_REG_SLV_SOFT_RESET, ACX_SLV_SOFT_RESET_BIT); - - /* SOFT_RESET is self clearing */ - timeout = jiffies + usecs_to_jiffies(SOFT_RESET_MAX_TIME); - while (1) { - boot_data = wl12xx_reg_read32(wl, ACX_REG_SLV_SOFT_RESET); - wl12xx_debug(DEBUG_BOOT, "soft reset bootdata 0x%x", boot_data); - if ((boot_data & ACX_SLV_SOFT_RESET_BIT) == 0) - break; - - if (time_after(jiffies, timeout)) { - /* 1.2 check pWhalBus->uSelfClearTime if the - * timeout was reached */ - wl12xx_error("soft reset timeout"); - return -1; - } - - udelay(SOFT_RESET_STALL_TIME); - } - - /* disable Rx/Tx */ - wl12xx_reg_write32(wl, ENABLE, 0x0); - - /* disable auto calibration on start*/ - wl12xx_reg_write32(wl, SPARE_A2, 0xffff); - - return 0; -} - -int wl12xx_boot_init_seq(struct wl12xx *wl) -{ - u32 scr_pad6, init_data, tmp, elp_cmd, ref_freq; - - /* - * col #1: INTEGER_DIVIDER - * col #2: FRACTIONAL_DIVIDER - * col #3: ATTN_BB - * col #4: ALPHA_BB - * col #5: STOP_TIME_BB - * col #6: BB_PLL_LOOP_FILTER - */ - static const u32 LUT[REF_FREQ_NUM][LUT_PARAM_NUM] = { - - { 83, 87381, 0xB, 5, 0xF00, 3}, /* REF_FREQ_19_2*/ - { 61, 141154, 0xB, 5, 0x1450, 2}, /* REF_FREQ_26_0*/ - { 41, 174763, 0xC, 6, 0x2D00, 1}, /* REF_FREQ_38_4*/ - { 40, 0, 0xC, 6, 0x2EE0, 1}, /* REF_FREQ_40_0*/ - { 47, 162280, 0xC, 6, 0x2760, 1} /* REF_FREQ_33_6 */ - }; - - /* read NVS params */ - scr_pad6 = wl12xx_reg_read32(wl, SCR_PAD6); - wl12xx_debug(DEBUG_BOOT, "scr_pad6 0x%x", scr_pad6); - - /* read ELP_CMD */ - elp_cmd = wl12xx_reg_read32(wl, ELP_CMD); - wl12xx_debug(DEBUG_BOOT, "elp_cmd 0x%x", elp_cmd); - - /* set the BB calibration time to be 300 usec (PLL_CAL_TIME) */ - ref_freq = scr_pad6 & 0x000000FF; - wl12xx_debug(DEBUG_BOOT, "ref_freq 0x%x", ref_freq); - - wl12xx_reg_write32(wl, PLL_CAL_TIME, 0x9); - - /* - * PG 1.2: set the clock buffer time to be 210 usec (CLK_BUF_TIME) - */ - wl12xx_reg_write32(wl, CLK_BUF_TIME, 0x6); - - /* - * set the clock detect feature to work in the restart wu procedure - * (ELP_CFG_MODE[14]) and Select the clock source type - * (ELP_CFG_MODE[13:12]) - */ - tmp = ((scr_pad6 & 0x0000FF00) << 4) | 0x00004000; - wl12xx_reg_write32(wl, ELP_CFG_MODE, tmp); - - /* PG 1.2: enable the BB PLL fix. Enable the PLL_LIMP_CLK_EN_CMD */ - elp_cmd |= 0x00000040; - wl12xx_reg_write32(wl, ELP_CMD, elp_cmd); - - /* PG 1.2: Set the BB PLL stable time to be 1000usec - * (PLL_STABLE_TIME) */ - wl12xx_reg_write32(wl, CFG_PLL_SYNC_CNT, 0x20); - - /* PG 1.2: read clock request time */ - init_data = wl12xx_reg_read32(wl, CLK_REQ_TIME); - - /* - * PG 1.2: set the clock request time to be ref_clk_settling_time - - * 1ms = 4ms - */ - if (init_data > 0x21) - tmp = init_data - 0x21; - else - tmp = 0; - wl12xx_reg_write32(wl, CLK_REQ_TIME, tmp); - - /* set BB PLL configurations in RF AFE */ - wl12xx_reg_write32(wl, 0x003058cc, 0x4B5); - - /* set RF_AFE_REG_5 */ - wl12xx_reg_write32(wl, 0x003058d4, 0x50); - - /* set RF_AFE_CTRL_REG_2 */ - wl12xx_reg_write32(wl, 0x00305948, 0x11c001); - - /* - * change RF PLL and BB PLL divider for VCO clock and adjust VCO - * bais current(RF_AFE_REG_13) - */ - wl12xx_reg_write32(wl, 0x003058f4, 0x1e); - - /* set BB PLL configurations */ - tmp = LUT[ref_freq][LUT_PARAM_INTEGER_DIVIDER] | 0x00017000; - wl12xx_reg_write32(wl, 0x00305840, tmp); - - /* set fractional divider according to Appendix C-BB PLL - * Calculations - */ - tmp = LUT[ref_freq][LUT_PARAM_FRACTIONAL_DIVIDER]; - wl12xx_reg_write32(wl, 0x00305844, tmp); - - /* set the initial data for the sigma delta */ - wl12xx_reg_write32(wl, 0x00305848, 0x3039); - - /* - * set the accumulator attenuation value, calibration loop1 - * (alpha), calibration loop2 (beta), calibration loop3 (gamma) and - * the VCO gain - */ - tmp = (LUT[ref_freq][LUT_PARAM_ATTN_BB] << 16) | - (LUT[ref_freq][LUT_PARAM_ALPHA_BB] << 12) | 0x1; - wl12xx_reg_write32(wl, 0x00305854, tmp); - - /* - * set the calibration stop time after holdoff time expires and set - * settling time HOLD_OFF_TIME_BB - */ - tmp = LUT[ref_freq][LUT_PARAM_STOP_TIME_BB] | 0x000A0000; - wl12xx_reg_write32(wl, 0x00305858, tmp); - - /* - * set BB PLL Loop filter capacitor3- BB_C3[2:0] and set BB PLL - * constant leakage current to linearize PFD to 0uA - - * BB_ILOOPF[7:3] - */ - tmp = LUT[ref_freq][LUT_PARAM_BB_PLL_LOOP_FILTER] | 0x00000030; - wl12xx_reg_write32(wl, 0x003058f8, tmp); - - /* - * set regulator output voltage for n divider to - * 1.35-BB_REFDIV[1:0], set charge pump current- BB_CPGAIN[4:2], - * set BB PLL Loop filter capacitor2- BB_C2[7:5], set gain of BB - * PLL auto-call to normal mode- BB_CALGAIN_3DB[8] - */ - wl12xx_reg_write32(wl, 0x003058f0, 0x29); - - /* enable restart wakeup sequence (ELP_CMD[0]) */ - wl12xx_reg_write32(wl, ELP_CMD, elp_cmd | 0x1); - - /* restart sequence completed */ - udelay(2000); - - return 0; -} - -int wl12xx_boot_run_firmware(struct wl12xx *wl) -{ - int loop, ret; - u32 chip_id, interrupt; - - wl->chip.op_set_ecpu_ctrl(wl, ECPU_CONTROL_HALT); - - chip_id = wl12xx_reg_read32(wl, CHIP_ID_B); - - wl12xx_debug(DEBUG_BOOT, "chip id after firmware boot: 0x%x", chip_id); - - if (chip_id != wl->chip.id) { - wl12xx_error("chip id doesn't match after firmware boot"); - return -EIO; - } - - /* wait for init to complete */ - loop = 0; - while (loop++ < INIT_LOOP) { - udelay(INIT_LOOP_DELAY); - interrupt = wl12xx_reg_read32(wl, ACX_REG_INTERRUPT_NO_CLEAR); - - if (interrupt == 0xffffffff) { - wl12xx_error("error reading hardware complete " - "init indication"); - return -EIO; - } - /* check that ACX_INTR_INIT_COMPLETE is enabled */ - else if (interrupt & wl->chip.intr_init_complete) { - wl12xx_reg_write32(wl, ACX_REG_INTERRUPT_ACK, - wl->chip.intr_init_complete); - break; - } - } - - if (loop >= INIT_LOOP) { - wl12xx_error("timeout waiting for the hardware to " - "complete initialization"); - return -EIO; - } - - /* get hardware config command mail box */ - wl->cmd_box_addr = wl12xx_reg_read32(wl, REG_COMMAND_MAILBOX_PTR); - - /* get hardware config event mail box */ - wl->event_box_addr = wl12xx_reg_read32(wl, REG_EVENT_MAILBOX_PTR); - - /* set the working partition to its "running" mode offset */ - wl12xx_set_partition(wl, - wl->chip.p_table[PART_WORK].mem.start, - wl->chip.p_table[PART_WORK].mem.size, - wl->chip.p_table[PART_WORK].reg.start, - wl->chip.p_table[PART_WORK].reg.size); - - wl12xx_debug(DEBUG_MAILBOX, "cmd_box_addr 0x%x event_box_addr 0x%x", - wl->cmd_box_addr, wl->event_box_addr); - - /* - * in case of full asynchronous mode the firmware event must be - * ready to receive event from the command mailbox - */ - - /* enable gpio interrupts */ - wl12xx_boot_enable_interrupts(wl); - - wl->chip.op_target_enable_interrupts(wl); - - /* unmask all mbox events */ - wl->event_mask = 0xffffffff; - - ret = wl12xx_event_unmask(wl); - if (ret < 0) { - wl12xx_error("EVENT mask setting failed"); - return ret; - } - - wl12xx_event_mbox_config(wl); - - /* firmware startup completed */ - return 0; -} |