diff options
Diffstat (limited to 'drivers/net/wireless/rt2x00/rt2800.h')
| -rw-r--r-- | drivers/net/wireless/rt2x00/rt2800.h | 109 |
1 files changed, 103 insertions, 6 deletions
diff --git a/drivers/net/wireless/rt2x00/rt2800.h b/drivers/net/wireless/rt2x00/rt2800.h index ed4ebcdde7c..eb8b6cab992 100644 --- a/drivers/net/wireless/rt2x00/rt2800.h +++ b/drivers/net/wireless/rt2x00/rt2800.h @@ -1,5 +1,6 @@ /* - Copyright (C) 2004 - 2009 Ivo van Doorn <IvDoorn@gmail.com> + Copyright (C) 2004 - 2010 Ivo van Doorn <IvDoorn@gmail.com> + Copyright (C) 2010 Willow Garage <http://www.willowgarage.com> Copyright (C) 2009 Alban Browaeys <prahal@yahoo.com> Copyright (C) 2009 Felix Fietkau <nbd@openwrt.org> Copyright (C) 2009 Luis Correia <luis.f.correia@gmail.com> @@ -639,6 +640,18 @@ #define LED_CFG_LED_POLAR FIELD32(0x40000000) /* + * AMPDU_BA_WINSIZE: Force BlockAck window size + * FORCE_WINSIZE_ENABLE: + * 0: Disable forcing of BlockAck window size + * 1: Enable forcing of BlockAck window size, overwrites values BlockAck + * window size values in the TXWI + * FORCE_WINSIZE: BlockAck window size + */ +#define AMPDU_BA_WINSIZE 0x1040 +#define AMPDU_BA_WINSIZE_FORCE_WINSIZE_ENABLE FIELD32(0x00000020) +#define AMPDU_BA_WINSIZE_FORCE_WINSIZE FIELD32(0x0000001f) + +/* * XIFS_TIME_CFG: MAC timing * CCKM_SIFS_TIME: unit 1us. Applied after CCK RX/TX * OFDM_SIFS_TIME: unit 1us. Applied after OFDM RX/TX @@ -698,8 +711,14 @@ /* * TBTT_SYNC_CFG: + * BCN_AIFSN: Beacon AIFSN after TBTT interrupt in slots + * BCN_CWMIN: Beacon CWMin after TBTT interrupt in slots */ #define TBTT_SYNC_CFG 0x1118 +#define TBTT_SYNC_CFG_TBTT_ADJUST FIELD32(0x000000ff) +#define TBTT_SYNC_CFG_BCN_EXP_WIN FIELD32(0x0000ff00) +#define TBTT_SYNC_CFG_BCN_AIFSN FIELD32(0x000f0000) +#define TBTT_SYNC_CFG_BCN_CWMIN FIELD32(0x00f00000) /* * TSF_TIMER_DW0: Local lsb TSF timer, read-only @@ -735,16 +754,21 @@ #define INT_TIMER_EN_GP_TIMER FIELD32(0x00000002) /* - * CH_IDLE_STA: channel idle time + * CH_IDLE_STA: channel idle time (in us) */ #define CH_IDLE_STA 0x1130 /* - * CH_BUSY_STA: channel busy time + * CH_BUSY_STA: channel busy time on primary channel (in us) */ #define CH_BUSY_STA 0x1134 /* + * CH_BUSY_STA_SEC: channel busy time on secondary channel in HT40 mode (in us) + */ +#define CH_BUSY_STA_SEC 0x1138 + +/* * MAC_STATUS_CFG: * BBP_RF_BUSY: When set to 0, BBP and RF are stable. * if 1 or higher one of the 2 registers is busy. @@ -1318,11 +1342,34 @@ #define TX_STA_CNT2_TX_UNDER_FLOW_COUNT FIELD32(0xffff0000) /* - * TX_STA_FIFO: TX Result for specific PID status fifo register + * TX_STA_FIFO: TX Result for specific PID status fifo register. + * + * This register is implemented as FIFO with 16 entries in the HW. Each + * register read fetches the next tx result. If the FIFO is full because + * it wasn't read fast enough after the according interrupt (TX_FIFO_STATUS) + * triggered, the hw seems to simply drop further tx results. + * + * VALID: 1: this tx result is valid + * 0: no valid tx result -> driver should stop reading + * PID_TYPE: The PID latched from the PID field in the TXWI, can be used + * to match a frame with its tx result (even though the PID is + * only 4 bits wide). + * PID_QUEUE: Part of PID_TYPE, this is the queue index number (0-3) + * PID_ENTRY: Part of PID_TYPE, this is the queue entry index number (1-3) + * This identification number is calculated by ((idx % 3) + 1). + * TX_SUCCESS: Indicates tx success (1) or failure (0) + * TX_AGGRE: Indicates if the frame was part of an aggregate (1) or not (0) + * TX_ACK_REQUIRED: Indicates if the frame needed to get ack'ed (1) or not (0) + * WCID: The wireless client ID. + * MCS: The tx rate used during the last transmission of this frame, be it + * successful or not. + * PHYMODE: The phymode used for the transmission. */ #define TX_STA_FIFO 0x1718 #define TX_STA_FIFO_VALID FIELD32(0x00000001) #define TX_STA_FIFO_PID_TYPE FIELD32(0x0000001e) +#define TX_STA_FIFO_PID_QUEUE FIELD32(0x00000006) +#define TX_STA_FIFO_PID_ENTRY FIELD32(0x00000018) #define TX_STA_FIFO_TX_SUCCESS FIELD32(0x00000020) #define TX_STA_FIFO_TX_AGGRE FIELD32(0x00000040) #define TX_STA_FIFO_TX_ACK_REQUIRED FIELD32(0x00000080) @@ -1405,6 +1452,24 @@ /* * Security key table memory. + * + * The pairwise key table shares some memory with the beacon frame + * buffers 6 and 7. That basically means that when beacon 6 & 7 + * are used we should only use the reduced pairwise key table which + * has a maximum of 222 entries. + * + * --------------------------------------------- + * |0x4000 | Pairwise Key | Reduced Pairwise | + * | | Table | Key Table | + * | | Size: 256 * 32 | Size: 222 * 32 | + * |0x5BC0 | |------------------- + * | | | Beacon 6 | + * |0x5DC0 | |------------------- + * | | | Beacon 7 | + * |0x5FC0 | |------------------- + * |0x5FFF | | + * -------------------------- + * * MAC_WCID_BASE: 8-bytes (use only 6 bytes) * 256 entry * PAIRWISE_KEY_TABLE_BASE: 32-byte * 256 entry * MAC_IVEIV_TABLE_BASE: 8-byte * 256-entry @@ -1554,7 +1619,8 @@ struct mac_iveiv_entry { * 2. Extract memory from FCE table for BCN 4~5 * 3. Extract memory from Pair-wise key table for BCN 6~7 * It occupied those memory of wcid 238~253 for BCN 6 - * and wcid 222~237 for BCN 7 + * and wcid 222~237 for BCN 7 (see Security key table memory + * for more info). * * IMPORTANT NOTE: Not sure why legacy driver does this, * but HW_BEACON_BASE7 is 0x0200 bytes below HW_BEACON_BASE6. @@ -1841,6 +1907,13 @@ struct mac_iveiv_entry { #define EEPROM_RSSI_A2_LNA_A2 FIELD16(0xff00) /* + * EEPROM Maximum TX power values + */ +#define EEPROM_MAX_TX_POWER 0x0027 +#define EEPROM_MAX_TX_POWER_24GHZ FIELD16(0x00ff) +#define EEPROM_MAX_TX_POWER_5GHZ FIELD16(0xff00) + +/* * EEPROM TXpower delta: 20MHZ AND 40 MHZ use different power. * This is delta in 40MHZ. * VALUE: Tx Power dalta value (MAX=4) @@ -1926,8 +1999,17 @@ struct mac_iveiv_entry { * FRAG: 1 To inform TKIP engine this is a fragment. * MIMO_PS: The remote peer is in dynamic MIMO-PS mode * TX_OP: 0:HT TXOP rule , 1:PIFS TX ,2:Backoff, 3:sifs - * BW: Channel bandwidth 20MHz or 40 MHz + * BW: Channel bandwidth 0:20MHz, 1:40 MHz (for legacy rates this will + * duplicate the frame to both channels). * STBC: 1: STBC support MCS =0-7, 2,3 : RESERVED + * AMPDU: 1: this frame is eligible for AMPDU aggregation, the hw will + * aggregate consecutive frames with the same RA and QoS TID. If + * a frame A with the same RA and QoS TID but AMPDU=0 is queued + * directly after a frame B with AMPDU=1, frame A might still + * get aggregated into the AMPDU started by frame B. So, setting + * AMPDU to 0 does _not_ necessarily mean the frame is sent as + * MPDU, it can still end up in an AMPDU if the previous frame + * was tagged as AMPDU. */ #define TXWI_W0_FRAG FIELD32(0x00000001) #define TXWI_W0_MIMO_PS FIELD32(0x00000002) @@ -1945,6 +2027,19 @@ struct mac_iveiv_entry { /* * Word1 + * ACK: 0: No Ack needed, 1: Ack needed + * NSEQ: 0: Don't assign hw sequence number, 1: Assign hw sequence number + * BW_WIN_SIZE: BA windows size of the recipient + * WIRELESS_CLI_ID: Client ID for WCID table access + * MPDU_TOTAL_BYTE_COUNT: Length of 802.11 frame + * PACKETID: Will be latched into the TX_STA_FIFO register once the according + * frame was processed. If multiple frames are aggregated together + * (AMPDU==1) the reported tx status will always contain the packet + * id of the first frame. 0: Don't report tx status for this frame. + * PACKETID_QUEUE: Part of PACKETID, This is the queue index (0-3) + * PACKETID_ENTRY: Part of PACKETID, THis is the queue entry index (1-3) + * This identification number is calculated by ((idx % 3) + 1). + * The (+1) is required to prevent PACKETID to become 0. */ #define TXWI_W1_ACK FIELD32(0x00000001) #define TXWI_W1_NSEQ FIELD32(0x00000002) @@ -1952,6 +2047,8 @@ struct mac_iveiv_entry { #define TXWI_W1_WIRELESS_CLI_ID FIELD32(0x0000ff00) #define TXWI_W1_MPDU_TOTAL_BYTE_COUNT FIELD32(0x0fff0000) #define TXWI_W1_PACKETID FIELD32(0xf0000000) +#define TXWI_W1_PACKETID_QUEUE FIELD32(0x30000000) +#define TXWI_W1_PACKETID_ENTRY FIELD32(0xc0000000) /* * Word2 |