diff options
Diffstat (limited to 'drivers/net/wireless/b43/phy_g.h')
| -rw-r--r-- | drivers/net/wireless/b43/phy_g.h | 209 |
1 files changed, 209 insertions, 0 deletions
diff --git a/drivers/net/wireless/b43/phy_g.h b/drivers/net/wireless/b43/phy_g.h new file mode 100644 index 00000000000..718947fd41a --- /dev/null +++ b/drivers/net/wireless/b43/phy_g.h @@ -0,0 +1,209 @@ +#ifndef LINUX_B43_PHY_G_H_ +#define LINUX_B43_PHY_G_H_ + +/* OFDM PHY registers are defined in the A-PHY header. */ +#include "phy_a.h" + +/* CCK (B) PHY Registers */ +#define B43_PHY_VERSION_CCK B43_PHY_CCK(0x00) /* Versioning register for B-PHY */ +#define B43_PHY_CCKBBANDCFG B43_PHY_CCK(0x01) /* Contains antenna 0/1 control bit */ +#define B43_PHY_PGACTL B43_PHY_CCK(0x15) /* PGA control */ +#define B43_PHY_PGACTL_LPF 0x1000 /* Low pass filter (?) */ +#define B43_PHY_PGACTL_LOWBANDW 0x0040 /* Low bandwidth flag */ +#define B43_PHY_PGACTL_UNKNOWN 0xEFA0 +#define B43_PHY_FBCTL1 B43_PHY_CCK(0x18) /* Frequency bandwidth control 1 */ +#define B43_PHY_ITSSI B43_PHY_CCK(0x29) /* Idle TSSI */ +#define B43_PHY_LO_LEAKAGE B43_PHY_CCK(0x2D) /* Measured LO leakage */ +#define B43_PHY_ENERGY B43_PHY_CCK(0x33) /* Energy */ +#define B43_PHY_SYNCCTL B43_PHY_CCK(0x35) +#define B43_PHY_FBCTL2 B43_PHY_CCK(0x38) /* Frequency bandwidth control 2 */ +#define B43_PHY_DACCTL B43_PHY_CCK(0x60) /* DAC control */ +#define B43_PHY_RCCALOVER B43_PHY_CCK(0x78) /* RC calibration override */ + +/* Extended G-PHY Registers */ +#define B43_PHY_CLASSCTL B43_PHY_EXTG(0x02) /* Classify control */ +#define B43_PHY_GTABCTL B43_PHY_EXTG(0x03) /* G-PHY table control (see below) */ +#define B43_PHY_GTABOFF 0x03FF /* G-PHY table offset (see below) */ +#define B43_PHY_GTABNR 0xFC00 /* G-PHY table number (see below) */ +#define B43_PHY_GTABNR_SHIFT 10 +#define B43_PHY_GTABDATA B43_PHY_EXTG(0x04) /* G-PHY table data */ +#define B43_PHY_LO_MASK B43_PHY_EXTG(0x0F) /* Local Oscillator control mask */ +#define B43_PHY_LO_CTL B43_PHY_EXTG(0x10) /* Local Oscillator control */ +#define B43_PHY_RFOVER B43_PHY_EXTG(0x11) /* RF override */ +#define B43_PHY_RFOVERVAL B43_PHY_EXTG(0x12) /* RF override value */ +#define B43_PHY_RFOVERVAL_EXTLNA 0x8000 +#define B43_PHY_RFOVERVAL_LNA 0x7000 +#define B43_PHY_RFOVERVAL_LNA_SHIFT 12 +#define B43_PHY_RFOVERVAL_PGA 0x0F00 +#define B43_PHY_RFOVERVAL_PGA_SHIFT 8 +#define B43_PHY_RFOVERVAL_UNK 0x0010 /* Unknown, always set. */ +#define B43_PHY_RFOVERVAL_TRSWRX 0x00E0 +#define B43_PHY_RFOVERVAL_BW 0x0003 /* Bandwidth flags */ +#define B43_PHY_RFOVERVAL_BW_LPF 0x0001 /* Low Pass Filter */ +#define B43_PHY_RFOVERVAL_BW_LBW 0x0002 /* Low Bandwidth (when set), high when unset */ +#define B43_PHY_ANALOGOVER B43_PHY_EXTG(0x14) /* Analog override */ +#define B43_PHY_ANALOGOVERVAL B43_PHY_EXTG(0x15) /* Analog override value */ + + +/*** G-PHY table numbers */ +#define B43_GTAB(number, offset) (((number) << B43_PHY_GTABNR_SHIFT) | (offset)) +#define B43_GTAB_NRSSI B43_GTAB(0x00, 0) +#define B43_GTAB_TRFEMW B43_GTAB(0x0C, 0x120) +#define B43_GTAB_ORIGTR B43_GTAB(0x2E, 0x298) + +u16 b43_gtab_read(struct b43_wldev *dev, u16 table, u16 offset); +void b43_gtab_write(struct b43_wldev *dev, u16 table, u16 offset, u16 value); + + +/* Returns the boolean whether "TX Magnification" is enabled. */ +#define has_tx_magnification(phy) \ + (((phy)->rev >= 2) && \ + ((phy)->radio_ver == 0x2050) && \ + ((phy)->radio_rev == 8)) +/* Card uses the loopback gain stuff */ +#define has_loopback_gain(phy) \ + (((phy)->rev > 1) || ((phy)->gmode)) + +/* Radio Attenuation (RF Attenuation) */ +struct b43_rfatt { + u8 att; /* Attenuation value */ + bool with_padmix; /* Flag, PAD Mixer enabled. */ +}; +struct b43_rfatt_list { + /* Attenuation values list */ + const struct b43_rfatt *list; + u8 len; + /* Minimum/Maximum attenuation values */ + u8 min_val; + u8 max_val; +}; + +/* Returns true, if the values are the same. */ +static inline bool b43_compare_rfatt(const struct b43_rfatt *a, + const struct b43_rfatt *b) +{ + return ((a->att == b->att) && + (a->with_padmix == b->with_padmix)); +} + +/* Baseband Attenuation */ +struct b43_bbatt { + u8 att; /* Attenuation value */ +}; +struct b43_bbatt_list { + /* Attenuation values list */ + const struct b43_bbatt *list; + u8 len; + /* Minimum/Maximum attenuation values */ + u8 min_val; + u8 max_val; +}; + +/* Returns true, if the values are the same. */ +static inline bool b43_compare_bbatt(const struct b43_bbatt *a, + const struct b43_bbatt *b) +{ + return (a->att == b->att); +} + +/* tx_control bits. */ +#define B43_TXCTL_PA3DB 0x40 /* PA Gain 3dB */ +#define B43_TXCTL_PA2DB 0x20 /* PA Gain 2dB */ +#define B43_TXCTL_TXMIX 0x10 /* TX Mixer Gain */ + +struct b43_txpower_lo_control; + +struct b43_phy_g { + /* ACI (adjacent channel interference) flags. */ + bool aci_enable; + bool aci_wlan_automatic; + bool aci_hw_rssi; + + /* Radio switched on/off */ + bool radio_on; + struct { + /* Values saved when turning the radio off. + * They are needed when turning it on again. */ + bool valid; + u16 rfover; + u16 rfoverval; + } radio_off_context; + + u16 minlowsig[2]; + u16 minlowsigpos[2]; + + /* Pointer to the table used to convert a + * TSSI value to dBm-Q5.2 */ + const s8 *tssi2dbm; + /* tssi2dbm is kmalloc()ed. Only used for free()ing. */ + bool dyn_tssi_tbl; + /* Target idle TSSI */ + int tgt_idle_tssi; + /* Current idle TSSI */ + int cur_idle_tssi; + /* The current average TSSI. + * Needs irq_lock, as it's updated in the IRQ path. */ + u8 average_tssi; + /* Current TX power level attenuation control values */ + struct b43_bbatt bbatt; + struct b43_rfatt rfatt; + u8 tx_control; /* B43_TXCTL_XXX */ + /* The calculated attenuation deltas that are used later + * when adjusting the actual power output. */ + int bbatt_delta; + int rfatt_delta; + + /* LocalOscillator control values. */ + struct b43_txpower_lo_control *lo_control; + /* Values from b43_calc_loopback_gain() */ + s16 max_lb_gain; /* Maximum Loopback gain in hdB */ + s16 trsw_rx_gain; /* TRSW RX gain in hdB */ + s16 lna_lod_gain; /* LNA lod */ + s16 lna_gain; /* LNA */ + s16 pga_gain; /* PGA */ + + /* Current Interference Mitigation mode */ + int interfmode; + /* Stack of saved values from the Interference Mitigation code. + * Each value in the stack is layed out as follows: + * bit 0-11: offset + * bit 12-15: register ID + * bit 16-32: value + * register ID is: 0x1 PHY, 0x2 Radio, 0x3 ILT + */ +#define B43_INTERFSTACK_SIZE 26 + u32 interfstack[B43_INTERFSTACK_SIZE]; //FIXME: use a data structure + + /* Saved values from the NRSSI Slope calculation */ + s16 nrssi[2]; + s32 nrssislope; + /* In memory nrssi lookup table. */ + s8 nrssi_lt[64]; + + u16 lofcal; + + u16 initval; //FIXME rename? + + /* The device does address auto increment for the OFDM tables. + * We cache the previously used address here and omit the address + * write on the next table access, if possible. */ + u16 ofdmtab_addr; /* The address currently set in hardware. */ + enum { /* The last data flow direction. */ + B43_OFDMTAB_DIRECTION_UNKNOWN = 0, + B43_OFDMTAB_DIRECTION_READ, + B43_OFDMTAB_DIRECTION_WRITE, + } ofdmtab_addr_direction; +}; + +void b43_gphy_set_baseband_attenuation(struct b43_wldev *dev, + u16 baseband_attenuation); +void b43_gphy_channel_switch(struct b43_wldev *dev, + unsigned int channel, + bool synthetic_pu_workaround); +u8 * b43_generate_dyn_tssi2dbm_tab(struct b43_wldev *dev, + s16 pab0, s16 pab1, s16 pab2); + +struct b43_phy_operations; +extern const struct b43_phy_operations b43_phyops_g; + +#endif /* LINUX_B43_PHY_G_H_ */ |