diff options
Diffstat (limited to 'drivers/net/wireless/ath/ath5k/reset.c')
| -rw-r--r-- | drivers/net/wireless/ath/ath5k/reset.c | 24 |
1 files changed, 12 insertions, 12 deletions
diff --git a/drivers/net/wireless/ath/ath5k/reset.c b/drivers/net/wireless/ath/ath5k/reset.c index 498aa28ea9e..4154959125b 100644 --- a/drivers/net/wireless/ath/ath5k/reset.c +++ b/drivers/net/wireless/ath/ath5k/reset.c @@ -959,7 +959,7 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, AR5K_QUEUE_DCU_SEQNUM(0)); } - /* TSF accelerates on AR5211 durring reset + /* TSF accelerates on AR5211 during reset * As a workaround save it here and restore * it later so that it's back in time after * reset. This way it'll get re-synced on the @@ -1080,7 +1080,7 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, return ret; /* Spur info is available only from EEPROM versions - * bigger than 5.3 but but the EEPOM routines will use + * greater than 5.3, but the EEPROM routines will use * static values for older versions */ if (ah->ah_mac_srev >= AR5K_SREV_AR5424) ath5k_hw_set_spur_mitigation_filter(ah, @@ -1160,7 +1160,7 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, */ /* Restore bssid and bssid mask */ - ath5k_hw_set_associd(ah); + ath5k_hw_set_bssid(ah); /* Set PCU config */ ath5k_hw_set_opmode(ah, op_mode); @@ -1173,11 +1173,11 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, /* Set RSSI/BRSSI thresholds * * Note: If we decide to set this value - * dynamicaly, have in mind that when AR5K_RSSI_THR - * register is read it might return 0x40 if we haven't - * wrote anything to it plus BMISS RSSI threshold is zeroed. + * dynamically, keep in mind that when AR5K_RSSI_THR + * register is read, it might return 0x40 if we haven't + * written anything to it. Also, BMISS RSSI threshold is zeroed. * So doing a save/restore procedure here isn't the right - * choice. Instead store it on ath5k_hw */ + * choice. Instead, store it in ath5k_hw */ ath5k_hw_reg_write(ah, (AR5K_TUNE_RSSI_THRES | AR5K_TUNE_BMISS_THRES << AR5K_RSSI_THR_BMISS_S), @@ -1235,7 +1235,7 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, /* * Perform ADC test to see if baseband is ready - * Set tx hold and check adc test register + * Set TX hold and check ADC test register */ phy_tst1 = ath5k_hw_reg_read(ah, AR5K_PHY_TST1); ath5k_hw_reg_write(ah, AR5K_PHY_TST1_TXHOLD, AR5K_PHY_TST1); @@ -1254,15 +1254,15 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, * * This method is used to calibrate some static offsets * used together with on-the fly I/Q calibration (the - * one performed via ath5k_hw_phy_calibrate), that doesn't + * one performed via ath5k_hw_phy_calibrate), which doesn't * interrupt rx path. * * While rx path is re-routed to the power detector we also - * start a noise floor calibration, to measure the + * start a noise floor calibration to measure the * card's noise floor (the noise we measure when we are not - * transmiting or receiving anything). + * transmitting or receiving anything). * - * If we are in a noisy environment AGC calibration may time + * If we are in a noisy environment, AGC calibration may time * out and/or noise floor calibration might timeout. */ AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGCCTL, |