diff options
Diffstat (limited to 'drivers/net/tokenring/tms380tr.h')
| -rw-r--r-- | drivers/net/tokenring/tms380tr.h | 1141 |
1 files changed, 0 insertions, 1141 deletions
diff --git a/drivers/net/tokenring/tms380tr.h b/drivers/net/tokenring/tms380tr.h deleted file mode 100644 index e5a617c586c..00000000000 --- a/drivers/net/tokenring/tms380tr.h +++ /dev/null @@ -1,1141 +0,0 @@ -/* - * tms380tr.h: TI TMS380 Token Ring driver for Linux - * - * Authors: - * - Christoph Goos <cgoos@syskonnect.de> - * - Adam Fritzler - */ - -#ifndef __LINUX_TMS380TR_H -#define __LINUX_TMS380TR_H - -#ifdef __KERNEL__ - -#include <linux/interrupt.h> - -/* module prototypes */ -extern const struct net_device_ops tms380tr_netdev_ops; -int tms380tr_open(struct net_device *dev); -int tms380tr_close(struct net_device *dev); -irqreturn_t tms380tr_interrupt(int irq, void *dev_id); -int tmsdev_init(struct net_device *dev, struct device *pdev); -void tmsdev_term(struct net_device *dev); -void tms380tr_wait(unsigned long time); - -#define TMS380TR_MAX_ADAPTERS 7 - -#define SEND_TIMEOUT 10*HZ - -#define TR_RCF_LONGEST_FRAME_MASK 0x0070 -#define TR_RCF_FRAME4K 0x0030 - -/*------------------------------------------------------------------*/ -/* Bit order for adapter communication with DMA */ -/* -------------------------------------------------------------- */ -/* Bit 8 | 9| 10| 11|| 12| 13| 14| 15|| 0| 1| 2| 3|| 4| 5| 6| 7| */ -/* -------------------------------------------------------------- */ -/* The bytes in a word must be byte swapped. Also, if a double */ -/* word is used for storage, then the words, as well as the bytes, */ -/* must be swapped. */ -/* Bit order for adapter communication with DIO */ -/* -------------------------------------------------------------- */ -/* Bit 0 | 1| 2| 3|| 4| 5| 6| 7|| 8| 9| 10| 11|| 12| 13| 14| 15| */ -/* -------------------------------------------------------------- */ -/*------------------------------------------------------------------*/ - -/* Swap words of a long. */ -#define SWAPW(x) (((x) << 16) | ((x) >> 16)) - -/* Get the low byte of a word. */ -#define LOBYTE(w) ((unsigned char)(w)) - -/* Get the high byte of a word. */ -#define HIBYTE(w) ((unsigned char)((unsigned short)(w) >> 8)) - -/* Get the low word of a long. */ -#define LOWORD(l) ((unsigned short)(l)) - -/* Get the high word of a long. */ -#define HIWORD(l) ((unsigned short)((unsigned long)(l) >> 16)) - - - -/* Token ring adapter I/O addresses for normal mode. */ - -/* - * The SIF registers. Common to all adapters. - */ -/* Basic SIF (SRSX = 0) */ -#define SIFDAT 0x00 /* SIF/DMA data. */ -#define SIFINC 0x02 /* IO Word data with auto increment. */ -#define SIFINH 0x03 /* IO Byte data with auto increment. */ -#define SIFADR 0x04 /* SIF/DMA Address. */ -#define SIFCMD 0x06 /* SIF Command. */ -#define SIFSTS 0x06 /* SIF Status. */ - -/* "Extended" SIF (SRSX = 1) */ -#define SIFACL 0x08 /* SIF Adapter Control Register. */ -#define SIFADD 0x0a /* SIF/DMA Address. -- 0x0a */ -#define SIFADX 0x0c /* 0x0c */ -#define DMALEN 0x0e /* SIF DMA length. -- 0x0e */ - -/* - * POS Registers. Only for ISA Adapters. - */ -#define POSREG 0x10 /* Adapter Program Option Select (POS) - * Register: base IO address + 16 byte. - */ -#define POSREG_2 24L /* only for TR4/16+ adapter - * base IO address + 24 byte. -- 0x18 - */ - -/* SIFCMD command codes (high-low) */ -#define CMD_INTERRUPT_ADAPTER 0x8000 /* Cause internal adapter interrupt */ -#define CMD_ADAPTER_RESET 0x4000 /* Hardware reset of adapter */ -#define CMD_SSB_CLEAR 0x2000 /* Acknowledge to adapter to - * system interrupts. - */ -#define CMD_EXECUTE 0x1000 /* Execute SCB command */ -#define CMD_SCB_REQUEST 0x0800 /* Request adapter to interrupt - * system when SCB is available for - * another command. - */ -#define CMD_RX_CONTINUE 0x0400 /* Continue receive after odd pointer - * stop. (odd pointer receive method) - */ -#define CMD_RX_VALID 0x0200 /* Now actual RPL is valid. */ -#define CMD_TX_VALID 0x0100 /* Now actual TPL is valid. (valid - * bit receive/transmit method) - */ -#define CMD_SYSTEM_IRQ 0x0080 /* Adapter-to-attached-system - * interrupt is reset. - */ -#define CMD_CLEAR_SYSTEM_IRQ 0x0080 /* Clear SYSTEM_INTERRUPT bit. - * (write: 1=ignore, 0=reset) - */ -#define EXEC_SOFT_RESET 0xFF00 /* adapter soft reset. (restart - * adapter after hardware reset) - */ - - -/* ACL commands (high-low) */ -#define ACL_SWHLDA 0x0800 /* Software hold acknowledge. */ -#define ACL_SWDDIR 0x0400 /* Data transfer direction. */ -#define ACL_SWHRQ 0x0200 /* Pseudo DMA operation. */ -#define ACL_PSDMAEN 0x0100 /* Enable pseudo system DMA. */ -#define ACL_ARESET 0x0080 /* Adapter hardware reset command. - * (held in reset condition as - * long as bit is set) - */ -#define ACL_CPHALT 0x0040 /* Communication processor halt. - * (can only be set while ACL_ARESET - * bit is set; prevents adapter - * processor from executing code while - * downloading firmware) - */ -#define ACL_BOOT 0x0020 -#define ACL_SINTEN 0x0008 /* System interrupt enable/disable - * (1/0): can be written if ACL_ARESET - * is zero. - */ -#define ACL_PEN 0x0004 - -#define ACL_NSELOUT0 0x0002 -#define ACL_NSELOUT1 0x0001 /* NSELOUTx have a card-specific - * meaning for setting ring speed. - */ - -#define PS_DMA_MASK (ACL_SWHRQ | ACL_PSDMAEN) - - -/* SIFSTS register return codes (high-low) */ -#define STS_SYSTEM_IRQ 0x0080 /* Adapter-to-attached-system - * interrupt is valid. - */ -#define STS_INITIALIZE 0x0040 /* INITIALIZE status. (ready to - * initialize) - */ -#define STS_TEST 0x0020 /* TEST status. (BUD not completed) */ -#define STS_ERROR 0x0010 /* ERROR status. (unrecoverable - * HW error occurred) - */ -#define STS_MASK 0x00F0 /* Mask interesting status bits. */ -#define STS_ERROR_MASK 0x000F /* Get Error Code by masking the - * interrupt code bits. - */ -#define ADAPTER_INT_PTRS 0x0A00 /* Address offset of adapter internal - * pointers 01:0a00 (high-low) have to - * be read after init and before open. - */ - - -/* Interrupt Codes (only MAC IRQs) */ -#define STS_IRQ_ADAPTER_CHECK 0x0000 /* unrecoverable hardware or - * software error. - */ -#define STS_IRQ_RING_STATUS 0x0004 /* SSB is updated with ring status. */ -#define STS_IRQ_LLC_STATUS 0x0005 /* Not used in MAC-only microcode */ -#define STS_IRQ_SCB_CLEAR 0x0006 /* SCB clear, following an - * SCB_REQUEST IRQ. - */ -#define STS_IRQ_TIMER 0x0007 /* Not normally used in MAC ucode */ -#define STS_IRQ_COMMAND_STATUS 0x0008 /* SSB is updated with command - * status. - */ -#define STS_IRQ_RECEIVE_STATUS 0x000A /* SSB is updated with receive - * status. - */ -#define STS_IRQ_TRANSMIT_STATUS 0x000C /* SSB is updated with transmit - * status - */ -#define STS_IRQ_RECEIVE_PENDING 0x000E /* Not used in MAC-only microcode */ -#define STS_IRQ_MASK 0x000F /* = STS_ERROR_MASK. */ - - -/* TRANSMIT_STATUS completion code: (SSB.Parm[0]) */ -#define COMMAND_COMPLETE 0x0080 /* TRANSMIT command completed - * (avoid this!) issue another transmit - * to send additional frames. - */ -#define FRAME_COMPLETE 0x0040 /* Frame has been transmitted; - * INTERRUPT_FRAME bit was set in the - * CSTAT request; indication of possibly - * more than one frame transmissions! - * SSB.Parm[0-1]: 32 bit pointer to - * TPL of last frame. - */ -#define LIST_ERROR 0x0020 /* Error in one of the TPLs that - * compose the frame; TRANSMIT - * terminated; Parm[1-2]: 32bit pointer - * to TPL which starts the error - * frame; error details in bits 8-13. - * (14?) - */ -#define FRAME_SIZE_ERROR 0x8000 /* FRAME_SIZE does not equal the sum of - * the valid DATA_COUNT fields; - * FRAME_SIZE less than header plus - * information field. (15 bytes + - * routing field) Or if FRAME_SIZE - * was specified as zero in one list. - */ -#define TX_THRESHOLD 0x4000 /* FRAME_SIZE greater than (BUFFER_SIZE - * - 9) * TX_BUF_MAX. - */ -#define ODD_ADDRESS 0x2000 /* Odd forward pointer value is - * read on a list without END_FRAME - * indication. - */ -#define FRAME_ERROR 0x1000 /* START_FRAME bit (not) anticipated, - * but (not) set. - */ -#define ACCESS_PRIORITY_ERROR 0x0800 /* Access priority requested has not - * been allowed. - */ -#define UNENABLED_MAC_FRAME 0x0400 /* MAC frame has source class of zero - * or MAC frame PCF ATTN field is - * greater than one. - */ -#define ILLEGAL_FRAME_FORMAT 0x0200 /* Bit 0 or FC field was set to one. */ - - -/* - * Since we need to support some functions even if the adapter is in a - * CLOSED state, we have a (pseudo-) command queue which holds commands - * that are outstandig to be executed. - * - * Each time a command completes, an interrupt occurs and the next - * command is executed. The command queue is actually a simple word with - * a bit for each outstandig command. Therefore the commands will not be - * executed in the order they have been queued. - * - * The following defines the command code bits and the command queue: - */ -#define OC_OPEN 0x0001 /* OPEN command */ -#define OC_TRANSMIT 0x0002 /* TRANSMIT command */ -#define OC_TRANSMIT_HALT 0x0004 /* TRANSMIT_HALT command */ -#define OC_RECEIVE 0x0008 /* RECEIVE command */ -#define OC_CLOSE 0x0010 /* CLOSE command */ -#define OC_SET_GROUP_ADDR 0x0020 /* SET_GROUP_ADDR command */ -#define OC_SET_FUNCT_ADDR 0x0040 /* SET_FUNCT_ADDR command */ -#define OC_READ_ERROR_LOG 0x0080 /* READ_ERROR_LOG command */ -#define OC_READ_ADAPTER 0x0100 /* READ_ADAPTER command */ -#define OC_MODIFY_OPEN_PARMS 0x0400 /* MODIFY_OPEN_PARMS command */ -#define OC_RESTORE_OPEN_PARMS 0x0800 /* RESTORE_OPEN_PARMS command */ -#define OC_SET_FIRST_16_GROUP 0x1000 /* SET_FIRST_16_GROUP command */ -#define OC_SET_BRIDGE_PARMS 0x2000 /* SET_BRIDGE_PARMS command */ -#define OC_CONFIG_BRIDGE_PARMS 0x4000 /* CONFIG_BRIDGE_PARMS command */ - -#define OPEN 0x0300 /* C: open command. S: completion. */ -#define TRANSMIT 0x0400 /* C: transmit command. S: completion - * status. (reject: COMMAND_REJECT if - * adapter not opened, TRANSMIT already - * issued or address passed in the SCB - * not word aligned) - */ -#define TRANSMIT_HALT 0x0500 /* C: interrupt TX TPL chain; if no - * TRANSMIT command issued, the command - * is ignored (completion with TRANSMIT - * status (0x0400)!) - */ -#define RECEIVE 0x0600 /* C: receive command. S: completion - * status. (reject: COMMAND_REJECT if - * adapter not opened, RECEIVE already - * issued or address passed in the SCB - * not word aligned) - */ -#define CLOSE 0x0700 /* C: close adapter. S: completion. - * (COMMAND_REJECT if adapter not open) - */ -#define SET_GROUP_ADDR 0x0800 /* C: alter adapter group address after - * OPEN. S: completion. (COMMAND_REJECT - * if adapter not open) - */ -#define SET_FUNCT_ADDR 0x0900 /* C: alter adapter functional address - * after OPEN. S: completion. - * (COMMAND_REJECT if adapter not open) - */ -#define READ_ERROR_LOG 0x0A00 /* C: read adapter error counters. - * S: completion. (command ignored - * if adapter not open!) - */ -#define READ_ADAPTER 0x0B00 /* C: read data from adapter memory. - * (important: after init and before - * open!) S: completion. (ADAPTER_CHECK - * interrupt if undefined storage area - * read) - */ -#define MODIFY_OPEN_PARMS 0x0D00 /* C: modify some adapter operational - * parameters. (bit correspondend to - * WRAP_INTERFACE is ignored) - * S: completion. (reject: - * COMMAND_REJECT) - */ -#define RESTORE_OPEN_PARMS 0x0E00 /* C: modify some adapter operational - * parameters. (bit correspondend - * to WRAP_INTERFACE is ignored) - * S: completion. (reject: - * COMMAND_REJECT) - */ -#define SET_FIRST_16_GROUP 0x0F00 /* C: alter the first two bytes in - * adapter group address. - * S: completion. (reject: - * COMMAND_REJECT) - */ -#define SET_BRIDGE_PARMS 0x1000 /* C: values and conditions for the - * adapter hardware to use when frames - * are copied for forwarding. - * S: completion. (reject: - * COMMAND_REJECT) - */ -#define CONFIG_BRIDGE_PARMS 0x1100 /* C: .. - * S: completion. (reject: - * COMMAND_REJECT) - */ - -#define SPEED_4 4 -#define SPEED_16 16 /* Default transmission speed */ - - -/* Initialization Parameter Block (IPB); word alignment necessary! */ -#define BURST_SIZE 0x0018 /* Default burst size */ -#define BURST_MODE 0x9F00 /* Burst mode enable */ -#define DMA_RETRIES 0x0505 /* Magic DMA retry number... */ - -#define CYCLE_TIME 3 /* Default AT-bus cycle time: 500 ns - * (later adapter version: fix cycle time!) - */ -#define LINE_SPEED_BIT 0x80 - -/* Macro definition for the wait function. */ -#define ONE_SECOND_TICKS 1000000 -#define HALF_SECOND (ONE_SECOND_TICKS / 2) -#define ONE_SECOND (ONE_SECOND_TICKS) -#define TWO_SECONDS (ONE_SECOND_TICKS * 2) -#define THREE_SECONDS (ONE_SECOND_TICKS * 3) -#define FOUR_SECONDS (ONE_SECOND_TICKS * 4) -#define FIVE_SECONDS (ONE_SECOND_TICKS * 5) - -#define BUFFER_SIZE 2048 /* Buffers on Adapter */ - -#pragma pack(1) -typedef struct { - unsigned short Init_Options; /* Initialize with burst mode; - * LLC disabled. (MAC only) - */ - - /* Interrupt vectors the adapter places on attached system bus. */ - u_int8_t CMD_Status_IV; /* Interrupt vector: command status. */ - u_int8_t TX_IV; /* Interrupt vector: transmit. */ - u_int8_t RX_IV; /* Interrupt vector: receive. */ - u_int8_t Ring_Status_IV; /* Interrupt vector: ring status. */ - u_int8_t SCB_Clear_IV; /* Interrupt vector: SCB clear. */ - u_int8_t Adapter_CHK_IV; /* Interrupt vector: adapter check. */ - - u_int16_t RX_Burst_Size; /* Max. number of transfer cycles. */ - u_int16_t TX_Burst_Size; /* During DMA burst; even value! */ - u_int16_t DMA_Abort_Thrhld; /* Number of DMA retries. */ - - u_int32_t SCB_Addr; /* SCB address: even, word aligned, high-low */ - u_int32_t SSB_Addr; /* SSB address: even, word aligned, high-low */ -} IPB, *IPB_Ptr; -#pragma pack() - -/* - * OPEN Command Parameter List (OCPL) (can be reused, if the adapter has to - * be reopened) - */ -#define BUFFER_SIZE 2048 /* Buffers on Adapter. */ -#define TPL_SIZE 8+6*TX_FRAG_NUM /* Depending on fragments per TPL. */ -#define RPL_SIZE 14 /* (with TI firmware v2.26 handling - * up to nine fragments possible) - */ -#define TX_BUF_MIN 20 /* ??? (Stephan: calculation with */ -#define TX_BUF_MAX 40 /* BUFFER_SIZE and MAX_FRAME_SIZE) ??? - */ -#define DISABLE_EARLY_TOKEN_RELEASE 0x1000 - -/* OPEN Options (high-low) */ -#define WRAP_INTERFACE 0x0080 /* Inserting omitted for test - * purposes; transmit data appears - * as receive data. (useful for - * testing; change: CLOSE necessary) - */ -#define DISABLE_HARD_ERROR 0x0040 /* On HARD_ERROR & TRANSMIT_BEACON - * no RING.STATUS interrupt. - */ -#define DISABLE_SOFT_ERROR 0x0020 /* On SOFT_ERROR, no RING.STATUS - * interrupt. - */ -#define PASS_ADAPTER_MAC_FRAMES 0x0010 /* Passing unsupported MAC frames - * to system. - */ -#define PASS_ATTENTION_FRAMES 0x0008 /* All changed attention MAC frames are - * passed to the system. - */ -#define PAD_ROUTING_FIELD 0x0004 /* Routing field is padded to 18 - * bytes. - */ -#define FRAME_HOLD 0x0002 /*Adapter waits for entire frame before - * initiating DMA transfer; otherwise: - * DMA transfer initiation if internal - * buffer filled. - */ -#define CONTENDER 0x0001 /* Adapter participates in the monitor - * contention process. - */ -#define PASS_BEACON_MAC_FRAMES 0x8000 /* Adapter passes beacon MAC frames - * to the system. - */ -#define EARLY_TOKEN_RELEASE 0x1000 /* Only valid in 16 Mbps operation; - * 0 = ETR. (no effect in 4 Mbps - * operation) - */ -#define COPY_ALL_MAC_FRAMES 0x0400 /* All MAC frames are copied to - * the system. (after OPEN: duplicate - * address test (DAT) MAC frame is - * first received frame copied to the - * system) - */ -#define COPY_ALL_NON_MAC_FRAMES 0x0200 /* All non MAC frames are copied to - * the system. - */ -#define PASS_FIRST_BUF_ONLY 0x0100 /* Passes only first internal buffer - * of each received frame; FrameSize - * of RPLs must contain internal - * BUFFER_SIZE bits for promiscuous mode. - */ -#define ENABLE_FULL_DUPLEX_SELECTION 0x2000 - /* Enable the use of full-duplex - * settings with bits in byte 22 in - * ocpl. (new feature in firmware - * version 3.09) - */ - -/* Full-duplex settings */ -#define OPEN_FULL_DUPLEX_OFF 0x0000 -#define OPEN_FULL_DUPLEX_ON 0x00c0 -#define OPEN_FULL_DUPLEX_AUTO 0x0080 - -#define PROD_ID_SIZE 18 /* Length of product ID. */ - -#define TX_FRAG_NUM 3 /* Number of fragments used in one TPL. */ -#define TX_MORE_FRAGMENTS 0x8000 /* Bit set in DataCount to indicate more - * fragments following. - */ - -/* XXX is there some better way to do this? */ -#define ISA_MAX_ADDRESS 0x00ffffff -#define PCI_MAX_ADDRESS 0xffffffff - -#pragma pack(1) -typedef struct { - u_int16_t OPENOptions; - u_int8_t NodeAddr[6]; /* Adapter node address; use ROM - * address - */ - u_int32_t GroupAddr; /* Multicast: high order - * bytes = 0xC000 - */ - u_int32_t FunctAddr; /* High order bytes = 0xC000 */ - __be16 RxListSize; /* RPL size: 0 (=26), 14, 20 or - * 26 bytes read by the adapter. - * (Depending on the number of - * fragments/list) - */ - __be16 TxListSize; /* TPL size */ - __be16 BufSize; /* Is automatically rounded up to the - * nearest nK boundary. - */ - u_int16_t FullDuplex; - u_int16_t Reserved; - u_int8_t TXBufMin; /* Number of adapter buffers reserved - * for transmission a minimum of 2 - * buffers must be allocated. - */ - u_int8_t TXBufMax; /* Maximum number of adapter buffers - * for transmit; a minimum of 2 buffers - * must be available for receive. - * Default: 6 - */ - u_int16_t ProdIDAddr[2];/* Pointer to product ID. */ -} OPB, *OPB_Ptr; -#pragma pack() - -/* - * SCB: adapter commands enabled by the host system started by writing - * CMD_INTERRUPT_ADAPTER | CMD_EXECUTE (|SCB_REQUEST) to the SIFCMD IO - * register. (special case: | CMD_SYSTEM_IRQ for initialization) - */ -#pragma pack(1) -typedef struct { - u_int16_t CMD; /* Command code */ - u_int16_t Parm[2]; /* Pointer to Command Parameter Block */ -} SCB; /* System Command Block (32 bit physical address; big endian)*/ -#pragma pack() - -/* - * SSB: adapter command return status can be evaluated after COMMAND_STATUS - * adapter to system interrupt after reading SSB, the availability of the SSB - * has to be told the adapter by writing CMD_INTERRUPT_ADAPTER | CMD_SSB_CLEAR - * in the SIFCMD IO register. - */ -#pragma pack(1) -typedef struct { - u_int16_t STS; /* Status code */ - u_int16_t Parm[3]; /* Parameter or pointer to Status Parameter - * Block. - */ -} SSB; /* System Status Block (big endian - physical address) */ -#pragma pack() - -typedef struct { - unsigned short BurnedInAddrPtr; /* Pointer to adapter burned in - * address. (BIA) - */ - unsigned short SoftwareLevelPtr;/* Pointer to software level data. */ - unsigned short AdapterAddrPtr; /* Pointer to adapter addresses. */ - unsigned short AdapterParmsPtr; /* Pointer to adapter parameters. */ - unsigned short MACBufferPtr; /* Pointer to MAC buffer. (internal) */ - unsigned short LLCCountersPtr; /* Pointer to LLC counters. */ - unsigned short SpeedFlagPtr; /* Pointer to data rate flag. - * (4/16 Mbps) - */ - unsigned short AdapterRAMPtr; /* Pointer to adapter RAM found. (KB) */ -} INTPTRS; /* Adapter internal pointers */ - -#pragma pack(1) -typedef struct { - u_int8_t Line_Error; /* Line error: code violation in - * frame or in a token, or FCS error. - */ - u_int8_t Internal_Error; /* IBM specific. (Reserved_1) */ - u_int8_t Burst_Error; - u_int8_t ARI_FCI_Error; /* ARI/FCI bit zero in AMP or - * SMP MAC frame. - */ - u_int8_t AbortDelimeters; /* IBM specific. (Reserved_2) */ - u_int8_t Reserved_3; - u_int8_t Lost_Frame_Error; /* Receive of end of transmitted - * frame failed. - */ - u_int8_t Rx_Congest_Error; /* Adapter in repeat mode has not - * enough buffer space to copy incoming - * frame. - */ - u_int8_t Frame_Copied_Error; /* ARI bit not zero in frame - * addressed to adapter. - */ - u_int8_t Frequency_Error; /* IBM specific. (Reserved_4) */ - u_int8_t Token_Error; /* (active only in monitor station) */ - u_int8_t Reserved_5; - u_int8_t DMA_Bus_Error; /* DMA bus errors not exceeding the - * abort thresholds. - */ - u_int8_t DMA_Parity_Error; /* DMA parity errors not exceeding - * the abort thresholds. - */ -} ERRORTAB; /* Adapter error counters */ -#pragma pack() - - -/*--------------------- Send and Receive definitions -------------------*/ -#pragma pack(1) -typedef struct { - __be16 DataCount; /* Value 0, even and odd values are - * permitted; value is unaltered most - * significant bit set: following - * fragments last fragment: most - * significant bit is not evaluated. - * (???) - */ - __be32 DataAddr; /* Pointer to frame data fragment; - * even or odd. - */ -} Fragment; -#pragma pack() - -#define MAX_FRAG_NUMBERS 9 /* Maximal number of fragments possible to use - * in one RPL/TPL. (depending on TI firmware - * version) - */ - -/* - * AC (1), FC (1), Dst (6), Src (6), RIF (18), Data (4472) = 4504 - * The packet size can be one of the follows: 548, 1502, 2084, 4504, 8176, - * 11439, 17832. Refer to TMS380 Second Generation Token Ring User's Guide - * Page 2-27. - */ -#define HEADER_SIZE (1 + 1 + 6 + 6) -#define SRC_SIZE 18 -#define MIN_DATA_SIZE 516 -#define DEFAULT_DATA_SIZE 4472 -#define MAX_DATA_SIZE 17800 - -#define DEFAULT_PACKET_SIZE (HEADER_SIZE + SRC_SIZE + DEFAULT_DATA_SIZE) -#define MIN_PACKET_SIZE (HEADER_SIZE + SRC_SIZE + MIN_DATA_SIZE) -#define MAX_PACKET_SIZE (HEADER_SIZE + SRC_SIZE + MAX_DATA_SIZE) - -/* - * Macros to deal with the frame status field. - */ -#define AC_NOT_RECOGNIZED 0x00 -#define GROUP_BIT 0x80 -#define GET_TRANSMIT_STATUS_HIGH_BYTE(Ts) ((unsigned char)((Ts) >> 8)) -#define GET_FRAME_STATUS_HIGH_AC(Fs) ((unsigned char)(((Fs) & 0xC0) >> 6)) -#define GET_FRAME_STATUS_LOW_AC(Fs) ((unsigned char)(((Fs) & 0x0C) >> 2)) -#define DIRECTED_FRAME(Context) (!((Context)->MData[2] & GROUP_BIT)) - - -/*--------------------- Send Functions ---------------------------------*/ -/* define TX_CSTAT _REQUEST (R) and _COMPLETE (C) values (high-low) */ - -#define TX_VALID 0x0080 /* R: set via TRANSMIT.VALID interrupt. - * C: always reset to zero! - */ -#define TX_FRAME_COMPLETE 0x0040 /* R: must be reset to zero. - * C: set to one. - */ -#define TX_START_FRAME 0x0020 /* R: start of a frame: 1 - * C: unchanged. - */ -#define TX_END_FRAME 0x0010 /* R: end of a frame: 1 - * C: unchanged. - */ -#define TX_FRAME_IRQ 0x0008 /* R: request interrupt generation - * after transmission. - * C: unchanged. - */ -#define TX_ERROR 0x0004 /* R: reserved. - * C: set to one if Error occurred. - */ -#define TX_INTERFRAME_WAIT 0x0004 -#define TX_PASS_CRC 0x0002 /* R: set if CRC value is already - * calculated. (valid only in - * FRAME_START TPL) - * C: unchanged. - */ -#define TX_PASS_SRC_ADDR 0x0001 /* R: adapter uses explicit frame - * source address and does not overwrite - * with the adapter node address. - * (valid only in FRAME_START TPL) - * - * C: unchanged. - */ -#define TX_STRIP_FS 0xFF00 /* R: reserved. - * C: if no Transmission Error, - * field contains copy of FS byte after - * stripping of frame. - */ - -/* - * Structure of Transmit Parameter Lists (TPLs) (only one frame every TPL, - * but possibly multiple TPLs for one frame) the length of the TPLs has to be - * initialized in the OPL. (OPEN parameter list) - */ -#define TPL_NUM 3 /* Number of Transmit Parameter Lists. - * !! MUST BE >= 3 !! - */ - -#pragma pack(1) -typedef struct s_TPL TPL; - -struct s_TPL { /* Transmit Parameter List (align on even word boundaries) */ - __be32 NextTPLAddr; /* Pointer to next TPL in chain; if - * pointer is odd: this is the last - * TPL. Pointing to itself can cause - * problems! - */ - volatile u_int16_t Status; /* Initialized by the adapter: - * CSTAT_REQUEST important: update least - * significant bit first! Set by the - * adapter: CSTAT_COMPLETE status. - */ - __be16 FrameSize; /* Number of bytes to be transmitted - * as a frame including AC/FC, - * Destination, Source, Routing field - * not including CRC, FS, End Delimiter - * (valid only if START_FRAME bit in - * CSTAT nonzero) must not be zero in - * any list; maximum value: (BUFFER_SIZE - * - 8) * TX_BUF_MAX sum of DataCount - * values in FragmentList must equal - * Frame_Size value in START_FRAME TPL! - * frame data fragment list. - */ - - /* TPL/RPL size in OPEN parameter list depending on maximal - * numbers of fragments used in one parameter list. - */ - Fragment FragList[TX_FRAG_NUM]; /* Maximum: nine frame fragments in one - * TPL actual version of firmware: 9 - * fragments possible. - */ -#pragma pack() - - /* Special proprietary data and precalculations */ - - TPL *NextTPLPtr; /* Pointer to next TPL in chain. */ - unsigned char *MData; - struct sk_buff *Skb; - unsigned char TPLIndex; - volatile unsigned char BusyFlag;/* Flag: TPL busy? */ - dma_addr_t DMABuff; /* DMA IO bus address from dma_map */ -}; - -/* ---------------------Receive Functions-------------------------------* - * define RECEIVE_CSTAT_REQUEST (R) and RECEIVE_CSTAT_COMPLETE (C) values. - * (high-low) - */ -#define RX_VALID 0x0080 /* R: set; tell adapter with - * RECEIVE.VALID interrupt. - * C: reset to zero. - */ -#define RX_FRAME_COMPLETE 0x0040 /* R: must be reset to zero, - * C: set to one. - */ -#define RX_START_FRAME 0x0020 /* R: must be reset to zero. - * C: set to one on the list. - */ -#define RX_END_FRAME 0x0010 /* R: must be reset to zero. - * C: set to one on the list - * that ends the frame. - */ -#define RX_FRAME_IRQ 0x0008 /* R: request interrupt generation - * after receive. - * C: unchanged. - */ -#define RX_INTERFRAME_WAIT 0x0004 /* R: after receiving a frame: - * interrupt and wait for a - * RECEIVE.CONTINUE. - * C: unchanged. - */ -#define RX_PASS_CRC 0x0002 /* R: if set, the adapter includes - * the CRC in data passed. (last four - * bytes; valid only if FRAME_START is - * set) - * C: set, if CRC is included in - * received data. - */ -#define RX_PASS_SRC_ADDR 0x0001 /* R: adapter uses explicit frame - * source address and does not - * overwrite with the adapter node - * address. (valid only if FRAME_START - * is set) - * C: unchanged. - */ -#define RX_RECEIVE_FS 0xFC00 /* R: reserved; must be reset to zero. - * C: on lists with START_FRAME, field - * contains frame status field from - * received frame; otherwise cleared. - */ -#define RX_ADDR_MATCH 0x0300 /* R: reserved; must be reset to zero. - * C: address match code mask. - */ -#define RX_STATUS_MASK 0x00FF /* Mask for receive status bits. */ - -#define RX_INTERN_ADDR_MATCH 0x0100 /* C: internally address match. */ -#define RX_EXTERN_ADDR_MATCH 0x0200 /* C: externally matched via - * XMATCH/XFAIL interface. - */ -#define RX_INTEXT_ADDR_MATCH 0x0300 /* C: internally and externally - * matched. - */ -#define RX_READY (RX_VALID | RX_FRAME_IRQ) /* Ready for receive. */ - -/* Constants for Command Status Interrupt. - * COMMAND_REJECT status field bit functions (SSB.Parm[0]) - */ -#define ILLEGAL_COMMAND 0x0080 /* Set if an unknown command - * is issued to the adapter - */ -#define ADDRESS_ERROR 0x0040 /* Set if any address field in - * the SCB is odd. (not word aligned) - */ -#define ADAPTER_OPEN 0x0020 /* Command issued illegal with - * open adapter. - */ -#define ADAPTER_CLOSE 0x0010 /* Command issued illegal with - * closed adapter. - */ -#define SAME_COMMAND 0x0008 /* Command issued with same command - * already executing. - */ - -/* OPEN_COMPLETION values (SSB.Parm[0], MSB) */ -#define NODE_ADDR_ERROR 0x0040 /* Wrong address or BIA read - * zero address. - */ -#define LIST_SIZE_ERROR 0x0020 /* If List_Size value not in 0, - * 14, 20, 26. - */ -#define BUF_SIZE_ERROR 0x0010 /* Not enough available memory for - * two buffers. - */ -#define TX_BUF_COUNT_ERROR 0x0004 /* Remaining receive buffers less than - * two. - */ -#define OPEN_ERROR 0x0002 /* Error during ring insertion; more - * information in bits 8-15. - */ - -/* Standard return codes */ -#define GOOD_COMPLETION 0x0080 /* =OPEN_SUCCESSFULL */ -#define INVALID_OPEN_OPTION 0x0001 /* OPEN options are not supported by - * the adapter. - */ - -/* OPEN phases; details of OPEN_ERROR (SSB.Parm[0], LSB) */ -#define OPEN_PHASES_MASK 0xF000 /* Check only the bits 8-11. */ -#define LOBE_MEDIA_TEST 0x1000 -#define PHYSICAL_INSERTION 0x2000 -#define ADDRESS_VERIFICATION 0x3000 -#define PARTICIPATION_IN_RING_POLL 0x4000 -#define REQUEST_INITIALISATION 0x5000 -#define FULLDUPLEX_CHECK 0x6000 - -/* OPEN error codes; details of OPEN_ERROR (SSB.Parm[0], LSB) */ -#define OPEN_ERROR_CODES_MASK 0x0F00 /* Check only the bits 12-15. */ -#define OPEN_FUNCTION_FAILURE 0x0100 /* Unable to transmit to itself or - * frames received before insertion. - */ -#define OPEN_SIGNAL_LOSS 0x0200 /* Signal loss condition detected at - * receiver. - */ -#define OPEN_TIMEOUT 0x0500 /* Insertion timer expired before - * logical insertion. - */ -#define OPEN_RING_FAILURE 0x0600 /* Unable to receive own ring purge - * MAC frames. - */ -#define OPEN_RING_BEACONING 0x0700 /* Beacon MAC frame received after - * ring insertion. - */ -#define OPEN_DUPLICATE_NODEADDR 0x0800 /* Other station in ring found - * with the same address. - */ -#define OPEN_REQUEST_INIT 0x0900 /* RPS present but does not respond. */ -#define OPEN_REMOVE_RECEIVED 0x0A00 /* Adapter received a remove adapter - * MAC frame. - */ -#define OPEN_FULLDUPLEX_SET 0x0D00 /* Got this with full duplex on when - * trying to connect to a normal ring. - */ - -/* SET_BRIDGE_PARMS return codes: */ -#define BRIDGE_INVALID_MAX_LEN 0x4000 /* MAX_ROUTING_FIELD_LENGTH odd, - * less than 6 or > 30. - */ -#define BRIDGE_INVALID_SRC_RING 0x2000 /* SOURCE_RING number zero, too large - * or = TARGET_RING. - */ -#define BRIDGE_INVALID_TRG_RING 0x1000 /* TARGET_RING number zero, too large - * or = SOURCE_RING. - */ -#define BRIDGE_INVALID_BRDGE_NO 0x0800 /* BRIDGE_NUMBER too large. */ -#define BRIDGE_INVALID_OPTIONS 0x0400 /* Invalid bridge options. */ -#define BRIDGE_DIAGS_FAILED 0x0200 /* Diagnostics of TMS380SRA failed. */ -#define BRIDGE_NO_SRA 0x0100 /* The TMS380SRA does not exist in HW - * configuration. - */ - -/* - * Bring Up Diagnostics error codes. - */ -#define BUD_INITIAL_ERROR 0x0 -#define BUD_CHECKSUM_ERROR 0x1 -#define BUD_ADAPTER_RAM_ERROR 0x2 -#define BUD_INSTRUCTION_ERROR 0x3 -#define BUD_CONTEXT_ERROR 0x4 -#define BUD_PROTOCOL_ERROR 0x5 -#define BUD_INTERFACE_ERROR 0x6 - -/* BUD constants */ -#define BUD_MAX_RETRIES 3 -#define BUD_MAX_LOOPCNT 6 -#define BUD_TIMEOUT 3000 - -/* Initialization constants */ -#define INIT_MAX_RETRIES 3 /* Maximum three retries. */ -#define INIT_MAX_LOOPCNT 22 /* Maximum loop counts. */ - -/* RING STATUS field values (high/low) */ -#define SIGNAL_LOSS 0x0080 /* Loss of signal on the ring - * detected. - */ -#define HARD_ERROR 0x0040 /* Transmitting or receiving beacon - * frames. - */ -#define SOFT_ERROR 0x0020 /* Report error MAC frame - * transmitted. - */ -#define TRANSMIT_BEACON 0x0010 /* Transmitting beacon frames on the - * ring. - */ -#define LOBE_WIRE_FAULT 0x0008 /* Open or short circuit in the - * cable to concentrator; adapter - * closed. - */ -#define AUTO_REMOVAL_ERROR 0x0004 /* Lobe wrap test failed, deinserted; - * adapter closed. - */ -#define REMOVE_RECEIVED 0x0001 /* Received a remove ring station MAC - * MAC frame request; adapter closed. - */ -#define COUNTER_OVERFLOW 0x8000 /* Overflow of one of the adapters - * error counters; READ.ERROR.LOG. - */ -#define SINGLE_STATION 0x4000 /* Adapter is the only station on the - * ring. - */ -#define RING_RECOVERY 0x2000 /* Claim token MAC frames on the ring; - * reset after ring purge frame. - */ - -#define ADAPTER_CLOSED (LOBE_WIRE_FAULT | AUTO_REMOVAL_ERROR |\ - REMOVE_RECEIVED) - -/* Adapter_check_block.Status field bit assignments: */ -#define DIO_PARITY 0x8000 /* Adapter detects bad parity - * through direct I/O access. - */ -#define DMA_READ_ABORT 0x4000 /* Aborting DMA read operation - * from system Parm[0]: 0=timeout, - * 1=parity error, 2=bus error; - * Parm[1]: 32 bit pointer to host - * system address at failure. - */ -#define DMA_WRITE_ABORT 0x2000 /* Aborting DMA write operation - * to system. (parameters analogous to - * DMA_READ_ABORT) - */ -#define ILLEGAL_OP_CODE 0x1000 /* Illegal operation code in the - * the adapters firmware Parm[0]-2: - * communications processor registers - * R13-R15. - */ -#define PARITY_ERRORS 0x0800 /* Adapter detects internal bus - * parity error. - */ -#define RAM_DATA_ERROR 0x0080 /* Valid only during RAM testing; - * RAM data error Parm[0-1]: 32 bit - * pointer to RAM location. - */ -#define RAM_PARITY_ERROR 0x0040 /* Valid only during RAM testing; - * RAM parity error Parm[0-1]: 32 bit - * pointer to RAM location. - */ -#define RING_UNDERRUN 0x0020 /* Internal DMA underrun when - * transmitting onto ring. - */ -#define INVALID_IRQ 0x0008 /* Unrecognized interrupt generated - * internal to adapter Parm[0-2]: - * adapter register R13-R15. - */ -#define INVALID_ERROR_IRQ 0x0004 /* Unrecognized error interrupt - * generated Parm[0-2]: adapter register - * R13-R15. - */ -#define INVALID_XOP 0x0002 /* Unrecognized XOP request in - * communication processor Parm[0-2]: - * adapter register R13-R15. - */ -#define CHECKADDR 0x05E0 /* Adapter check status information - * address offset. - */ -#define ROM_PAGE_0 0x0000 /* Adapter ROM page 0. */ - -/* - * RECEIVE.STATUS interrupt result SSB values: (high-low) - * (RECEIVE_COMPLETE field bit definitions in SSB.Parm[0]) - */ -#define RX_COMPLETE 0x0080 /* SSB.Parm[0]; SSB.Parm[1]: 32 - * bit pointer to last RPL. - */ -#define RX_SUSPENDED 0x0040 /* SSB.Parm[0]; SSB.Parm[1]: 32 - * bit pointer to RPL with odd - * forward pointer. - */ - -/* Valid receive CSTAT: */ -#define RX_FRAME_CONTROL_BITS (RX_VALID | RX_START_FRAME | RX_END_FRAME | \ - RX_FRAME_COMPLETE) -#define VALID_SINGLE_BUFFER_FRAME (RX_START_FRAME | RX_END_FRAME | \ - RX_FRAME_COMPLETE) - -typedef enum SKB_STAT SKB_STAT; -enum SKB_STAT { - SKB_UNAVAILABLE, - SKB_DMA_DIRECT, - SKB_DATA_COPY -}; - -/* Receive Parameter List (RPL) The length of the RPLs has to be initialized - * in the OPL. (OPEN parameter list) - */ -#define RPL_NUM 3 - -#define RX_FRAG_NUM 1 /* Maximal number of used fragments in one RPL. - * (up to firmware v2.24: 3, now: up to 9) - */ - -#pragma pack(1) -typedef struct s_RPL RPL; -struct s_RPL { /* Receive Parameter List */ - __be32 NextRPLAddr; /* Pointer to next RPL in chain - * (normalized = physical 32 bit - * address) if pointer is odd: this - * is last RPL. Pointing to itself can - * cause problems! - */ - volatile u_int16_t Status; /* Set by creation of Receive Parameter - * List RECEIVE_CSTAT_COMPLETE set by - * adapter in lists that start or end - * a frame. - */ - volatile __be16 FrameSize; /* Number of bytes received as a - * frame including AC/FC, Destination, - * Source, Routing field not including - * CRC, FS (Frame Status), End Delimiter - * (valid only if START_FRAME bit in - * CSTAT nonzero) must not be zero in - * any list; maximum value: (BUFFER_SIZE - * - 8) * TX_BUF_MAX sum of DataCount - * values in FragmentList must equal - * Frame_Size value in START_FRAME TPL! - * frame data fragment list - */ - - /* TPL/RPL size in OPEN parameter list depending on maximal numbers - * of fragments used in one parameter list. - */ - Fragment FragList[RX_FRAG_NUM]; /* Maximum: nine frame fragments in - * one TPL. Actual version of firmware: - * 9 fragments possible. - */ -#pragma pack() - - /* Special proprietary data and precalculations. */ - RPL *NextRPLPtr; /* Logical pointer to next RPL in chain. */ - unsigned char *MData; - struct sk_buff *Skb; - SKB_STAT SkbStat; - int RPLIndex; - dma_addr_t DMABuff; /* DMA IO bus address from dma_map */ -}; - -/* Information that need to be kept for each board. */ -typedef struct net_local { -#pragma pack(1) - IPB ipb; /* Initialization Parameter Block. */ - SCB scb; /* System Command Block: system to adapter - * communication. - */ - SSB ssb; /* System Status Block: adapter to system - * communication. - */ - OPB ocpl; /* Open Options Parameter Block. */ - - ERRORTAB errorlogtable; /* Adapter statistic error counters. - * (read from adapter memory) - */ - unsigned char ProductID[PROD_ID_SIZE + 1]; /* Product ID */ -#pragma pack() - - TPL Tpl[TPL_NUM]; - TPL *TplFree; - TPL *TplBusy; - unsigned char LocalTxBuffers[TPL_NUM][DEFAULT_PACKET_SIZE]; - - RPL Rpl[RPL_NUM]; - RPL *RplHead; - RPL *RplTail; - unsigned char LocalRxBuffers[RPL_NUM][DEFAULT_PACKET_SIZE]; - - struct device *pdev; - int DataRate; - unsigned char ScbInUse; - unsigned short CMDqueue; - - unsigned long AdapterOpenFlag:1; - unsigned long AdapterVirtOpenFlag:1; - unsigned long OpenCommandIssued:1; - unsigned long TransmitCommandActive:1; - unsigned long TransmitHaltScheduled:1; - unsigned long HaltInProgress:1; - unsigned long LobeWireFaultLogged:1; - unsigned long ReOpenInProgress:1; - unsigned long Sleeping:1; - - unsigned long LastOpenStatus; - unsigned short CurrentRingStatus; - unsigned long MaxPacketSize; - - unsigned long StartTime; - unsigned long LastSendTime; - - struct tr_statistics MacStat; /* MAC statistics structure */ - - unsigned long dmalimit; /* the max DMA address (ie, ISA) */ - dma_addr_t dmabuffer; /* the DMA bus address corresponding to - priv. Might be different from virt_to_bus() - for architectures with IO MMU (Alpha) */ - - struct timer_list timer; - - wait_queue_head_t wait_for_tok_int; - - INTPTRS intptrs; /* Internal adapter pointer. Must be read - * before OPEN command. - */ - unsigned short (*setnselout)(struct net_device *); - unsigned short (*sifreadb)(struct net_device *, unsigned short); - void (*sifwriteb)(struct net_device *, unsigned short, unsigned short); - unsigned short (*sifreadw)(struct net_device *, unsigned short); - void (*sifwritew)(struct net_device *, unsigned short, unsigned short); - - spinlock_t lock; /* SMP protection */ - void *tmspriv; -} NET_LOCAL; - -#endif /* __KERNEL__ */ -#endif /* __LINUX_TMS380TR_H */ |