diff options
Diffstat (limited to 'drivers/net/irda')
-rw-r--r-- | drivers/net/irda/sa1100_ir.c | 262 |
1 files changed, 131 insertions, 131 deletions
diff --git a/drivers/net/irda/sa1100_ir.c b/drivers/net/irda/sa1100_ir.c index 9dc564830c9..32ac4a44ce7 100644 --- a/drivers/net/irda/sa1100_ir.c +++ b/drivers/net/irda/sa1100_ir.c @@ -230,137 +230,6 @@ sa1100_set_power(struct sa1100_irda *si, unsigned int state) return ret; } -static int sa1100_irda_startup(struct sa1100_irda *si) -{ - int ret; - - /* - * Ensure that the ports for this device are setup correctly. - */ - if (si->pdata->startup) { - ret = si->pdata->startup(si->dev); - if (ret) - return ret; - } - - /* - * Configure PPC for IRDA - we want to drive TXD2 low. - * We also want to drive this pin low during sleep. - */ - PPSR &= ~PPC_TXD2; - PSDR &= ~PPC_TXD2; - PPDR |= PPC_TXD2; - - /* - * Enable HP-SIR modulation, and ensure that the port is disabled. - */ - Ser2UTCR3 = 0; - Ser2HSCR0 = HSCR0_UART; - Ser2UTCR4 = si->utcr4; - Ser2UTCR0 = UTCR0_8BitData; - Ser2HSCR2 = HSCR2_TrDataH | HSCR2_RcDataL; - - /* - * Clear status register - */ - Ser2UTSR0 = UTSR0_REB | UTSR0_RBB | UTSR0_RID; - - ret = sa1100_irda_set_speed(si, si->speed = 9600); - if (ret) { - Ser2UTCR3 = 0; - Ser2HSCR0 = 0; - - if (si->pdata->shutdown) - si->pdata->shutdown(si->dev); - } - - return ret; -} - -static void sa1100_irda_shutdown(struct sa1100_irda *si) -{ - /* - * Stop all DMA activity. - */ - sa1100_stop_dma(si->dma_rx.regs); - sa1100_stop_dma(si->dma_tx.regs); - - /* Disable the port. */ - Ser2UTCR3 = 0; - Ser2HSCR0 = 0; - - if (si->pdata->shutdown) - si->pdata->shutdown(si->dev); -} - -#ifdef CONFIG_PM -/* - * Suspend the IrDA interface. - */ -static int sa1100_irda_suspend(struct platform_device *pdev, pm_message_t state) -{ - struct net_device *dev = platform_get_drvdata(pdev); - struct sa1100_irda *si; - - if (!dev) - return 0; - - si = netdev_priv(dev); - if (si->open) { - /* - * Stop the transmit queue - */ - netif_device_detach(dev); - disable_irq(dev->irq); - sa1100_irda_shutdown(si); - __sa1100_irda_set_power(si, 0); - } - - return 0; -} - -/* - * Resume the IrDA interface. - */ -static int sa1100_irda_resume(struct platform_device *pdev) -{ - struct net_device *dev = platform_get_drvdata(pdev); - struct sa1100_irda *si; - - if (!dev) - return 0; - - si = netdev_priv(dev); - if (si->open) { - /* - * If we missed a speed change, initialise at the new speed - * directly. It is debatable whether this is actually - * required, but in the interests of continuing from where - * we left off it is desirable. The converse argument is - * that we should re-negotiate at 9600 baud again. - */ - if (si->newspeed) { - si->speed = si->newspeed; - si->newspeed = 0; - } - - sa1100_irda_startup(si); - __sa1100_irda_set_power(si, si->power); - enable_irq(dev->irq); - - /* - * This automatically wakes up the queue - */ - netif_device_attach(dev); - } - - return 0; -} -#else -#define sa1100_irda_suspend NULL -#define sa1100_irda_resume NULL -#endif - /* * HP-SIR format interrupt service routines. */ @@ -774,6 +643,69 @@ sa1100_irda_ioctl(struct net_device *dev, struct ifreq *ifreq, int cmd) return ret; } +static int sa1100_irda_startup(struct sa1100_irda *si) +{ + int ret; + + /* + * Ensure that the ports for this device are setup correctly. + */ + if (si->pdata->startup) { + ret = si->pdata->startup(si->dev); + if (ret) + return ret; + } + + /* + * Configure PPC for IRDA - we want to drive TXD2 low. + * We also want to drive this pin low during sleep. + */ + PPSR &= ~PPC_TXD2; + PSDR &= ~PPC_TXD2; + PPDR |= PPC_TXD2; + + /* + * Enable HP-SIR modulation, and ensure that the port is disabled. + */ + Ser2UTCR3 = 0; + Ser2HSCR0 = HSCR0_UART; + Ser2UTCR4 = si->utcr4; + Ser2UTCR0 = UTCR0_8BitData; + Ser2HSCR2 = HSCR2_TrDataH | HSCR2_RcDataL; + + /* + * Clear status register + */ + Ser2UTSR0 = UTSR0_REB | UTSR0_RBB | UTSR0_RID; + + ret = sa1100_irda_set_speed(si, si->speed = 9600); + if (ret) { + Ser2UTCR3 = 0; + Ser2HSCR0 = 0; + + if (si->pdata->shutdown) + si->pdata->shutdown(si->dev); + } + + return ret; +} + +static void sa1100_irda_shutdown(struct sa1100_irda *si) +{ + /* + * Stop all DMA activity. + */ + sa1100_stop_dma(si->dma_rx.regs); + sa1100_stop_dma(si->dma_tx.regs); + + /* Disable the port. */ + Ser2UTCR3 = 0; + Ser2HSCR0 = 0; + + if (si->pdata->shutdown) + si->pdata->shutdown(si->dev); +} + static int sa1100_irda_start(struct net_device *dev) { struct sa1100_irda *si = netdev_priv(dev); @@ -1024,6 +956,74 @@ static int sa1100_irda_remove(struct platform_device *pdev) return 0; } +#ifdef CONFIG_PM +/* + * Suspend the IrDA interface. + */ +static int sa1100_irda_suspend(struct platform_device *pdev, pm_message_t state) +{ + struct net_device *dev = platform_get_drvdata(pdev); + struct sa1100_irda *si; + + if (!dev) + return 0; + + si = netdev_priv(dev); + if (si->open) { + /* + * Stop the transmit queue + */ + netif_device_detach(dev); + disable_irq(dev->irq); + sa1100_irda_shutdown(si); + __sa1100_irda_set_power(si, 0); + } + + return 0; +} + +/* + * Resume the IrDA interface. + */ +static int sa1100_irda_resume(struct platform_device *pdev) +{ + struct net_device *dev = platform_get_drvdata(pdev); + struct sa1100_irda *si; + + if (!dev) + return 0; + + si = netdev_priv(dev); + if (si->open) { + /* + * If we missed a speed change, initialise at the new speed + * directly. It is debatable whether this is actually + * required, but in the interests of continuing from where + * we left off it is desirable. The converse argument is + * that we should re-negotiate at 9600 baud again. + */ + if (si->newspeed) { + si->speed = si->newspeed; + si->newspeed = 0; + } + + sa1100_irda_startup(si); + __sa1100_irda_set_power(si, si->power); + enable_irq(dev->irq); + + /* + * This automatically wakes up the queue + */ + netif_device_attach(dev); + } + + return 0; +} +#else +#define sa1100_irda_suspend NULL +#define sa1100_irda_resume NULL +#endif + static struct platform_driver sa1100ir_driver = { .probe = sa1100_irda_probe, .remove = sa1100_irda_remove, |