diff options
Diffstat (limited to 'drivers/net/irda/vlsi_ir.h')
| -rw-r--r-- | drivers/net/irda/vlsi_ir.h | 798 |
1 files changed, 798 insertions, 0 deletions
diff --git a/drivers/net/irda/vlsi_ir.h b/drivers/net/irda/vlsi_ir.h new file mode 100644 index 00000000000..414694abf58 --- /dev/null +++ b/drivers/net/irda/vlsi_ir.h @@ -0,0 +1,798 @@ + +/********************************************************************* + * + * vlsi_ir.h: VLSI82C147 PCI IrDA controller driver for Linux + * + * Version: 0.5 + * + * Copyright (c) 2001-2003 Martin Diehl + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + ********************************************************************/ + +#ifndef IRDA_VLSI_FIR_H +#define IRDA_VLSI_FIR_H + +/* ================================================================ + * compatibility stuff + */ + +/* definitions not present in pci_ids.h */ + +#ifndef PCI_CLASS_WIRELESS_IRDA +#define PCI_CLASS_WIRELESS_IRDA 0x0d00 +#endif + +#ifndef PCI_CLASS_SUBCLASS_MASK +#define PCI_CLASS_SUBCLASS_MASK 0xffff +#endif + +/* in recent 2.5 interrupt handlers have non-void return value */ +#ifndef IRQ_RETVAL +typedef void irqreturn_t; +#define IRQ_NONE +#define IRQ_HANDLED +#define IRQ_RETVAL(x) +#endif + +/* some stuff need to check kernelversion. Not all 2.5 stuff was present + * in early 2.5.x - the test is merely to separate 2.4 from 2.5 + */ +#include <linux/version.h> + +#if LINUX_VERSION_CODE < KERNEL_VERSION(2,5,0) + +/* PDE() introduced in 2.5.4 */ +#ifdef CONFIG_PROC_FS +#define PDE(inode) ((inode)->u.generic_ip) +#endif + +/* irda crc16 calculation exported in 2.5.42 */ +#define irda_calc_crc16(fcs,buf,len) (GOOD_FCS) + +/* we use this for unified pci device name access */ +#define PCIDEV_NAME(pdev) ((pdev)->name) + +#else /* 2.5 or later */ + +/* recent 2.5/2.6 stores pci device names at varying places ;-) */ +#ifdef CONFIG_PCI_NAMES +/* human readable name */ +#define PCIDEV_NAME(pdev) ((pdev)->pretty_name) +#else +/* whatever we get from the associated struct device - bus:slot:dev.fn id */ +#define PCIDEV_NAME(pdev) (pci_name(pdev)) +#endif + +#endif + +/* ================================================================ */ + +/* non-standard PCI registers */ + +enum vlsi_pci_regs { + VLSI_PCI_CLKCTL = 0x40, /* chip clock input control */ + VLSI_PCI_MSTRPAGE = 0x41, /* addr [31:24] for all busmaster cycles */ + VLSI_PCI_IRMISC = 0x42 /* mainly legacy UART related */ +}; + +/* ------------------------------------------ */ + +/* VLSI_PCI_CLKCTL: Clock Control Register (u8, rw) */ + +/* Three possible clock sources: either on-chip 48MHz PLL or + * external clock applied to EXTCLK pin. External clock may + * be either 48MHz or 40MHz, which is indicated by XCKSEL. + * CLKSTP controls whether the selected clock source gets + * connected to the IrDA block. + * + * On my HP OB-800 the BIOS sets external 40MHz clock as source + * when IrDA enabled and I've never detected any PLL lock success. + * Apparently the 14.3...MHz OSC input required for the PLL to work + * is not connected and the 40MHz EXTCLK is provided externally. + * At least this is what makes the driver working for me. + */ + +enum vlsi_pci_clkctl { + + /* PLL control */ + + CLKCTL_PD_INV = 0x04, /* PD#: inverted power down signal, + * i.e. PLL is powered, if PD_INV set */ + CLKCTL_LOCK = 0x40, /* (ro) set, if PLL is locked */ + + /* clock source selection */ + + CLKCTL_EXTCLK = 0x20, /* set to select external clock input, not PLL */ + CLKCTL_XCKSEL = 0x10, /* set to indicate EXTCLK is 40MHz, not 48MHz */ + + /* IrDA block control */ + + CLKCTL_CLKSTP = 0x80, /* set to disconnect from selected clock source */ + CLKCTL_WAKE = 0x08 /* set to enable wakeup feature: whenever IR activity + * is detected, PD_INV gets set(?) and CLKSTP cleared */ +}; + +/* ------------------------------------------ */ + +/* VLSI_PCI_MSTRPAGE: Master Page Register (u8, rw) and busmastering stuff */ + +#define DMA_MASK_USED_BY_HW 0xffffffff +#define DMA_MASK_MSTRPAGE 0x00ffffff +#define MSTRPAGE_VALUE (DMA_MASK_MSTRPAGE >> 24) + + /* PCI busmastering is somewhat special for this guy - in short: + * + * We select to operate using fixed MSTRPAGE=0, use ISA DMA + * address restrictions to make the PCI BM api aware of this, + * but ensure the hardware is dealing with real 32bit access. + * + * In detail: + * The chip executes normal 32bit busmaster cycles, i.e. + * drives all 32 address lines. These addresses however are + * composed of [0:23] taken from various busaddr-pointers + * and [24:31] taken from the MSTRPAGE register in the VLSI82C147 + * config space. Therefore _all_ busmastering must be + * targeted to/from one single 16MB (busaddr-) superpage! + * The point is to make sure all the allocations for memory + * locations with busmaster access (ring descriptors, buffers) + * are indeed bus-mappable to the same 16MB range (for x86 this + * means they must reside in the same 16MB physical memory address + * range). The only constraint we have which supports "several objects + * mappable to common 16MB range" paradigma, is the old ISA DMA + * restriction to the first 16MB of physical address range. + * Hence the approach here is to enable PCI busmaster support using + * the correct 32bit dma-mask used by the chip. Afterwards the device's + * dma-mask gets restricted to 24bit, which must be honoured somehow by + * all allocations for memory areas to be exposed to the chip ... + * + * Note: + * Don't be surprised to get "Setting latency timer..." messages every + * time when PCI busmastering is enabled for the chip. + * The chip has its PCI latency timer RO fixed at 0 - which is not a + * problem here, because it is never requesting _burst_ transactions. + */ + +/* ------------------------------------------ */ + +/* VLSI_PCIIRMISC: IR Miscellaneous Register (u8, rw) */ + +/* legacy UART emulation - not used by this driver - would require: + * (see below for some register-value definitions) + * + * - IRMISC_UARTEN must be set to enable UART address decoding + * - IRMISC_UARTSEL configured + * - IRCFG_MASTER must be cleared + * - IRCFG_SIR must be set + * - IRENABLE_PHYANDCLOCK must be asserted 0->1 (and hence IRENABLE_SIR_ON) + */ + +enum vlsi_pci_irmisc { + + /* IR transceiver control */ + + IRMISC_IRRAIL = 0x40, /* (ro?) IR rail power indication (and control?) + * 0=3.3V / 1=5V. Probably set during power-on? + * unclear - not touched by driver */ + IRMISC_IRPD = 0x08, /* transceiver power down, if set */ + + /* legacy UART control */ + + IRMISC_UARTTST = 0x80, /* UART test mode - "always write 0" */ + IRMISC_UARTEN = 0x04, /* enable UART address decoding */ + + /* bits [1:0] IRMISC_UARTSEL to select legacy UART address */ + + IRMISC_UARTSEL_3f8 = 0x00, + IRMISC_UARTSEL_2f8 = 0x01, + IRMISC_UARTSEL_3e8 = 0x02, + IRMISC_UARTSEL_2e8 = 0x03 +}; + +/* ================================================================ */ + +/* registers mapped to 32 byte PCI IO space */ + +/* note: better access all registers at the indicated u8/u16 size + * although some of them contain only 1 byte of information. + * some of them (particaluarly PROMPT and IRCFG) ignore + * access when using the wrong addressing mode! + */ + +enum vlsi_pio_regs { + VLSI_PIO_IRINTR = 0x00, /* interrupt enable/request (u8, rw) */ + VLSI_PIO_RINGPTR = 0x02, /* rx/tx ring pointer (u16, ro) */ + VLSI_PIO_RINGBASE = 0x04, /* [23:10] of ring address (u16, rw) */ + VLSI_PIO_RINGSIZE = 0x06, /* rx/tx ring size (u16, rw) */ + VLSI_PIO_PROMPT = 0x08, /* triggers ring processing (u16, wo) */ + /* 0x0a-0x0f: reserved / duplicated UART regs */ + VLSI_PIO_IRCFG = 0x10, /* configuration select (u16, rw) */ + VLSI_PIO_SIRFLAG = 0x12, /* BOF/EOF for filtered SIR (u16, ro) */ + VLSI_PIO_IRENABLE = 0x14, /* enable and status register (u16, rw/ro) */ + VLSI_PIO_PHYCTL = 0x16, /* physical layer current status (u16, ro) */ + VLSI_PIO_NPHYCTL = 0x18, /* next physical layer select (u16, rw) */ + VLSI_PIO_MAXPKT = 0x1a, /* [11:0] max len for packet receive (u16, rw) */ + VLSI_PIO_RCVBCNT = 0x1c /* current receive-FIFO byte count (u16, ro) */ + /* 0x1e-0x1f: reserved / duplicated UART regs */ +}; + +/* ------------------------------------------ */ + +/* VLSI_PIO_IRINTR: Interrupt Register (u8, rw) */ + +/* enable-bits: + * 1 = enable / 0 = disable + * interrupt condition bits: + * set according to corresponding interrupt source + * (regardless of the state of the enable bits) + * enable bit status indicates whether interrupt gets raised + * write-to-clear + * note: RPKTINT and TPKTINT behave different in legacy UART mode (which we don't use :-) + */ + +enum vlsi_pio_irintr { + IRINTR_ACTEN = 0x80, /* activity interrupt enable */ + IRINTR_ACTIVITY = 0x40, /* activity monitor (traffic detected) */ + IRINTR_RPKTEN = 0x20, /* receive packet interrupt enable*/ + IRINTR_RPKTINT = 0x10, /* rx-packet transfered from fifo to memory finished */ + IRINTR_TPKTEN = 0x08, /* transmit packet interrupt enable */ + IRINTR_TPKTINT = 0x04, /* last bit of tx-packet+crc shifted to ir-pulser */ + IRINTR_OE_EN = 0x02, /* UART rx fifo overrun error interrupt enable */ + IRINTR_OE_INT = 0x01 /* UART rx fifo overrun error (read LSR to clear) */ +}; + +/* we use this mask to check whether the (shared PCI) interrupt is ours */ + +#define IRINTR_INT_MASK (IRINTR_ACTIVITY|IRINTR_RPKTINT|IRINTR_TPKTINT) + +/* ------------------------------------------ */ + +/* VLSI_PIO_RINGPTR: Ring Pointer Read-Back Register (u16, ro) */ + +/* _both_ ring pointers are indices relative to the _entire_ rx,tx-ring! + * i.e. the referenced descriptor is located + * at RINGBASE + PTR * sizeof(descr) for rx and tx + * therefore, the tx-pointer has offset MAX_RING_DESCR + */ + +#define MAX_RING_DESCR 64 /* tx, rx rings may contain up to 64 descr each */ + +#define RINGPTR_RX_MASK (MAX_RING_DESCR-1) +#define RINGPTR_TX_MASK ((MAX_RING_DESCR-1)<<8) + +#define RINGPTR_GET_RX(p) ((p)&RINGPTR_RX_MASK) +#define RINGPTR_GET_TX(p) (((p)&RINGPTR_TX_MASK)>>8) + +/* ------------------------------------------ */ + +/* VLSI_PIO_RINGBASE: Ring Pointer Base Address Register (u16, ro) */ + +/* Contains [23:10] part of the ring base (bus-) address + * which must be 1k-alinged. [31:24] is taken from + * VLSI_PCI_MSTRPAGE above. + * The controller initiates non-burst PCI BM cycles to + * fetch and update the descriptors in the ring. + * Once fetched, the descriptor remains cached onchip + * until it gets closed and updated due to the ring + * processing state machine. + * The entire ring area is split in rx and tx areas with each + * area consisting of 64 descriptors of 8 bytes each. + * The rx(tx) ring is located at ringbase+0 (ringbase+64*8). + */ + +#define BUS_TO_RINGBASE(p) (((p)>>10)&0x3fff) + +/* ------------------------------------------ */ + +/* VLSI_PIO_RINGSIZE: Ring Size Register (u16, rw) */ + +/* bit mask to indicate the ring size to be used for rx and tx. + * possible values encoded bits + * 4 0000 + * 8 0001 + * 16 0011 + * 32 0111 + * 64 1111 + * located at [15:12] for tx and [11:8] for rx ([7:0] unused) + * + * note: probably a good idea to have IRCFG_MSTR cleared when writing + * this so the state machines are stopped and the RINGPTR is reset! + */ + +#define SIZE_TO_BITS(num) ((((num)-1)>>2)&0x0f) +#define TX_RX_TO_RINGSIZE(tx,rx) ((SIZE_TO_BITS(tx)<<12)|(SIZE_TO_BITS(rx)<<8)) +#define RINGSIZE_TO_RXSIZE(rs) ((((rs)&0x0f00)>>6)+4) +#define RINGSIZE_TO_TXSIZE(rs) ((((rs)&0xf000)>>10)+4) + + +/* ------------------------------------------ */ + +/* VLSI_PIO_PROMPT: Ring Prompting Register (u16, write-to-start) */ + +/* writing any value kicks the ring processing state machines + * for both tx, rx rings as follows: + * - active rings (currently owning an active descriptor) + * ignore the prompt and continue + * - idle rings fetch the next descr from the ring and start + * their processing + */ + +/* ------------------------------------------ */ + +/* VLSI_PIO_IRCFG: IR Config Register (u16, rw) */ + +/* notes: + * - not more than one SIR/MIR/FIR bit must be set at any time + * - SIR, MIR, FIR and CRC16 select the configuration which will + * be applied on next 0->1 transition of IRENABLE_PHYANDCLOCK (see below). + * - besides allowing the PCI interface to execute busmaster cycles + * and therefore the ring SM to operate, the MSTR bit has side-effects: + * when MSTR is cleared, the RINGPTR's get reset and the legacy UART mode + * (in contrast to busmaster access mode) gets enabled. + * - clearing ENRX or setting ENTX while data is received may stall the + * receive fifo until ENRX reenabled _and_ another packet arrives + * - SIRFILT means the chip performs the required unwrapping of hardware + * headers (XBOF's, BOF/EOF) and un-escaping in the _receive_ direction. + * Only the resulting IrLAP payload is copied to the receive buffers - + * but with the 16bit FCS still encluded. Question remains, whether it + * was already checked or we should do it before passing the packet to IrLAP? + */ + +enum vlsi_pio_ircfg { + IRCFG_LOOP = 0x4000, /* enable loopback test mode */ + IRCFG_ENTX = 0x1000, /* transmit enable */ + IRCFG_ENRX = 0x0800, /* receive enable */ + IRCFG_MSTR = 0x0400, /* master enable */ + IRCFG_RXANY = 0x0200, /* receive any packet */ + IRCFG_CRC16 = 0x0080, /* 16bit (not 32bit) CRC select for MIR/FIR */ + IRCFG_FIR = 0x0040, /* FIR 4PPM encoding mode enable */ + IRCFG_MIR = 0x0020, /* MIR HDLC encoding mode enable */ + IRCFG_SIR = 0x0010, /* SIR encoding mode enable */ + IRCFG_SIRFILT = 0x0008, /* enable SIR decode filter (receiver unwrapping) */ + IRCFG_SIRTEST = 0x0004, /* allow SIR decode filter when not in SIR mode */ + IRCFG_TXPOL = 0x0002, /* invert tx polarity when set */ + IRCFG_RXPOL = 0x0001 /* invert rx polarity when set */ +}; + +/* ------------------------------------------ */ + +/* VLSI_PIO_SIRFLAG: SIR Flag Register (u16, ro) */ + +/* register contains hardcoded BOF=0xc0 at [7:0] and EOF=0xc1 at [15:8] + * which is used for unwrapping received frames in SIR decode-filter mode + */ + +/* ------------------------------------------ */ + +/* VLSI_PIO_IRENABLE: IR Enable Register (u16, rw/ro) */ + +/* notes: + * - IREN acts as gate for latching the configured IR mode information + * from IRCFG and IRPHYCTL when IREN=reset and applying them when + * IREN gets set afterwards. + * - ENTXST reflects IRCFG_ENTX + * - ENRXST = IRCFG_ENRX && (!IRCFG_ENTX || IRCFG_LOOP) + */ + +enum vlsi_pio_irenable { + IRENABLE_PHYANDCLOCK = 0x8000, /* enable IR phy and gate the mode config (rw) */ + IRENABLE_CFGER = 0x4000, /* mode configuration error (ro) */ + IRENABLE_FIR_ON = 0x2000, /* FIR on status (ro) */ + IRENABLE_MIR_ON = 0x1000, /* MIR on status (ro) */ + IRENABLE_SIR_ON = 0x0800, /* SIR on status (ro) */ + IRENABLE_ENTXST = 0x0400, /* transmit enable status (ro) */ + IRENABLE_ENRXST = 0x0200, /* Receive enable status (ro) */ + IRENABLE_CRC16_ON = 0x0100 /* 16bit (not 32bit) CRC enabled status (ro) */ +}; + +#define IRENABLE_MASK 0xff00 /* Read mask */ + +/* ------------------------------------------ */ + +/* VLSI_PIO_PHYCTL: IR Physical Layer Current Control Register (u16, ro) */ + +/* read-back of the currently applied physical layer status. + * applied from VLSI_PIO_NPHYCTL at rising edge of IRENABLE_PHYANDCLOCK + * contents identical to VLSI_PIO_NPHYCTL (see below) + */ + +/* ------------------------------------------ */ + +/* VLSI_PIO_NPHYCTL: IR Physical Layer Next Control Register (u16, rw) */ + +/* latched during IRENABLE_PHYANDCLOCK=0 and applied at 0-1 transition + * + * consists of BAUD[15:10], PLSWID[9:5] and PREAMB[4:0] bits defined as follows: + * + * SIR-mode: BAUD = (115.2kHz / baudrate) - 1 + * PLSWID = (pulsetime * freq / (BAUD+1)) - 1 + * where pulsetime is the requested IrPHY pulse width + * and freq is 8(16)MHz for 40(48)MHz primary input clock + * PREAMB: don't care for SIR + * + * The nominal SIR pulse width is 3/16 bit time so we have PLSWID=12 + * fixed for all SIR speeds at 40MHz input clock (PLSWID=24 at 48MHz). + * IrPHY also allows shorter pulses down to the nominal pulse duration + * at 115.2kbaud (minus some tolerance) which is 1.41 usec. + * Using the expression PLSWID = 12/(BAUD+1)-1 (multiplied by two for 48MHz) + * we get the minimum acceptable PLSWID values according to the VLSI + * specification, which provides 1.5 usec pulse width for all speeds (except + * for 2.4kbaud getting 6usec). This is fine with IrPHY v1.3 specs and + * reduces the transceiver power which drains the battery. At 9.6kbaud for + * example this amounts to more than 90% battery power saving! + * + * MIR-mode: BAUD = 0 + * PLSWID = 9(10) for 40(48) MHz input clock + * to get nominal MIR pulse width + * PREAMB = 1 + * + * FIR-mode: BAUD = 0 + * PLSWID: don't care + * PREAMB = 15 + */ + +#define PHYCTL_BAUD_SHIFT 10 +#define PHYCTL_BAUD_MASK 0xfc00 +#define PHYCTL_PLSWID_SHIFT 5 +#define PHYCTL_PLSWID_MASK 0x03e0 +#define PHYCTL_PREAMB_SHIFT 0 +#define PHYCTL_PREAMB_MASK 0x001f + +#define PHYCTL_TO_BAUD(bwp) (((bwp)&PHYCTL_BAUD_MASK)>>PHYCTL_BAUD_SHIFT) +#define PHYCTL_TO_PLSWID(bwp) (((bwp)&PHYCTL_PLSWID_MASK)>>PHYCTL_PLSWID_SHIFT) +#define PHYCTL_TO_PREAMB(bwp) (((bwp)&PHYCTL_PREAMB_MASK)>>PHYCTL_PREAMB_SHIFT) + +#define BWP_TO_PHYCTL(b,w,p) ((((b)<<PHYCTL_BAUD_SHIFT)&PHYCTL_BAUD_MASK) \ + | (((w)<<PHYCTL_PLSWID_SHIFT)&PHYCTL_PLSWID_MASK) \ + | (((p)<<PHYCTL_PREAMB_SHIFT)&PHYCTL_PREAMB_MASK)) + +#define BAUD_BITS(br) ((115200/(br))-1) + +static inline unsigned +calc_width_bits(unsigned baudrate, unsigned widthselect, unsigned clockselect) +{ + unsigned tmp; + + if (widthselect) /* nominal 3/16 puls width */ + return (clockselect) ? 12 : 24; + + tmp = ((clockselect) ? 12 : 24) / (BAUD_BITS(baudrate)+1); + + /* intermediate result of integer division needed here */ + + return (tmp>0) ? (tmp-1) : 0; +} + +#define PHYCTL_SIR(br,ws,cs) BWP_TO_PHYCTL(BAUD_BITS(br),calc_width_bits((br),(ws),(cs)),0) +#define PHYCTL_MIR(cs) BWP_TO_PHYCTL(0,((cs)?9:10),1) +#define PHYCTL_FIR BWP_TO_PHYCTL(0,0,15) + +/* quite ugly, I know. But implementing these calculations here avoids + * having magic numbers in the code and allows some playing with pulsewidths + * without risk to violate the standards. + * FWIW, here is the table for reference: + * + * baudrate BAUD min-PLSWID nom-PLSWID PREAMB + * 2400 47 0(0) 12(24) 0 + * 9600 11 0(0) 12(24) 0 + * 19200 5 1(2) 12(24) 0 + * 38400 2 3(6) 12(24) 0 + * 57600 1 5(10) 12(24) 0 + * 115200 0 11(22) 12(24) 0 + * MIR 0 - 9(10) 1 + * FIR 0 - 0 15 + * + * note: x(y) means x-value for 40MHz / y-value for 48MHz primary input clock + */ + +/* ------------------------------------------ */ + + +/* VLSI_PIO_MAXPKT: Maximum Packet Length register (u16, rw) */ + +/* maximum acceptable length for received packets */ + +/* hw imposed limitation - register uses only [11:0] */ +#define MAX_PACKET_LENGTH 0x0fff + +/* IrLAP I-field (apparently not defined elsewhere) */ +#define IRDA_MTU 2048 + +/* complete packet consists of A(1)+C(1)+I(<=IRDA_MTU) */ +#define IRLAP_SKB_ALLOCSIZE (1+1+IRDA_MTU) + +/* the buffers we use to exchange frames with the hardware need to be + * larger than IRLAP_SKB_ALLOCSIZE because we may have up to 4 bytes FCS + * appended and, in SIR mode, a lot of frame wrapping bytes. The worst + * case appears to be a SIR packet with I-size==IRDA_MTU and all bytes + * requiring to be escaped to provide transparency. Furthermore, the peer + * might ask for quite a number of additional XBOFs: + * up to 115+48 XBOFS 163 + * regular BOF 1 + * A-field 1 + * C-field 1 + * I-field, IRDA_MTU, all escaped 4096 + * FCS (16 bit at SIR, escaped) 4 + * EOF 1 + * AFAICS nothing in IrLAP guarantees A/C field not to need escaping + * (f.e. 0xc0/0xc1 - i.e. BOF/EOF - are legal values there) so in the + * worst case we have 4269 bytes total frame size. + * However, the VLSI uses 12 bits only for all buffer length values, + * which limits the maximum useable buffer size <= 4095. + * Note this is not a limitation in the receive case because we use + * the SIR filtering mode where the hw unwraps the frame and only the + * bare packet+fcs is stored into the buffer - in contrast to the SIR + * tx case where we have to pass frame-wrapped packets to the hw. + * If this would ever become an issue in real life, the only workaround + * I see would be using the legacy UART emulation in SIR mode. + */ + +#define XFER_BUF_SIZE MAX_PACKET_LENGTH + +/* ------------------------------------------ */ + +/* VLSI_PIO_RCVBCNT: Receive Byte Count Register (u16, ro) */ + +/* receive packet counter gets incremented on every non-filtered + * byte which was put in the receive fifo and reset for each + * new packet. Used to decide whether we are just in the middle + * of receiving + */ + +/* better apply the [11:0] mask when reading, as some docs say the + * reserved [15:12] would return 1 when reading - which is wrong AFAICS + */ +#define RCVBCNT_MASK 0x0fff + +/******************************************************************/ + +/* descriptors for rx/tx ring + * + * accessed by hardware - don't change! + * + * the descriptor is owned by hardware, when the ACTIVE status bit + * is set and nothing (besides reading status to test the bit) + * shall be done. The bit gets cleared by hw, when the descriptor + * gets closed. Premature reaping of descriptors owned be the chip + * can be achieved by disabling IRCFG_MSTR + * + * Attention: Writing addr overwrites status! + * + * ### FIXME: depends on endianess (but there ain't no non-i586 ob800 ;-) + */ + +struct ring_descr_hw { + volatile u16 rd_count; /* tx/rx count [11:0] */ + u16 reserved; + union { + u32 addr; /* [23:0] of the buffer's busaddress */ + struct { + u8 addr_res[3]; + volatile u8 status; /* descriptor status */ + } rd_s __attribute__((packed)); + } rd_u __attribute((packed)); +} __attribute__ ((packed)); + +#define rd_addr rd_u.addr +#define rd_status rd_u.rd_s.status + +/* ring descriptor status bits */ + +#define RD_ACTIVE 0x80 /* descriptor owned by hw (both TX,RX) */ + +/* TX ring descriptor status */ + +#define RD_TX_DISCRC 0x40 /* do not send CRC (for SIR) */ +#define RD_TX_BADCRC 0x20 /* force a bad CRC */ +#define RD_TX_PULSE 0x10 /* send indication pulse after this frame (MIR/FIR) */ +#define RD_TX_FRCEUND 0x08 /* force underrun */ +#define RD_TX_CLRENTX 0x04 /* clear ENTX after this frame */ +#define RD_TX_UNDRN 0x01 /* TX fifo underrun (probably PCI problem) */ + +/* RX ring descriptor status */ + +#define RD_RX_PHYERR 0x40 /* physical encoding error */ +#define RD_RX_CRCERR 0x20 /* CRC error (MIR/FIR) */ +#define RD_RX_LENGTH 0x10 /* frame exceeds buffer length */ +#define RD_RX_OVER 0x08 /* RX fifo overrun (probably PCI problem) */ +#define RD_RX_SIRBAD 0x04 /* EOF missing: BOF follows BOF (SIR, filtered) */ + +#define RD_RX_ERROR 0x7c /* any error in received frame */ + +/* the memory required to hold the 2 descriptor rings */ +#define HW_RING_AREA_SIZE (2 * MAX_RING_DESCR * sizeof(struct ring_descr_hw)) + +/******************************************************************/ + +/* sw-ring descriptors consists of a bus-mapped transfer buffer with + * associated skb and a pointer to the hw entry descriptor + */ + +struct ring_descr { + struct ring_descr_hw *hw; + struct sk_buff *skb; + void *buf; +}; + +/* wrappers for operations on hw-exposed ring descriptors + * access to the hw-part of the descriptors must use these. + */ + +static inline int rd_is_active(struct ring_descr *rd) +{ + return ((rd->hw->rd_status & RD_ACTIVE) != 0); +} + +static inline void rd_activate(struct ring_descr *rd) +{ + rd->hw->rd_status |= RD_ACTIVE; +} + +static inline void rd_set_status(struct ring_descr *rd, u8 s) +{ + rd->hw->rd_status = s; /* may pass ownership to the hardware */ +} + +static inline void rd_set_addr_status(struct ring_descr *rd, dma_addr_t a, u8 s) +{ + /* order is important for two reasons: + * - overlayed: writing addr overwrites status + * - we want to write status last so we have valid address in + * case status has RD_ACTIVE set + */ + + if ((a & ~DMA_MASK_MSTRPAGE)>>24 != MSTRPAGE_VALUE) { + IRDA_ERROR("%s: pci busaddr inconsistency!\n", __FUNCTION__); + dump_stack(); + return; + } + + a &= DMA_MASK_MSTRPAGE; /* clear highbyte to make sure we won't write + * to status - just in case MSTRPAGE_VALUE!=0 + */ + rd->hw->rd_addr = cpu_to_le32(a); + wmb(); + rd_set_status(rd, s); /* may pass ownership to the hardware */ +} + +static inline void rd_set_count(struct ring_descr *rd, u16 c) +{ + rd->hw->rd_count = cpu_to_le16(c); +} + +static inline u8 rd_get_status(struct ring_descr *rd) +{ + return rd->hw->rd_status; +} + +static inline dma_addr_t rd_get_addr(struct ring_descr *rd) +{ + dma_addr_t a; + + a = le32_to_cpu(rd->hw->rd_addr); + return (a & DMA_MASK_MSTRPAGE) | (MSTRPAGE_VALUE << 24); +} + +static inline u16 rd_get_count(struct ring_descr *rd) +{ + return le16_to_cpu(rd->hw->rd_count); +} + +/******************************************************************/ + +/* sw descriptor rings for rx, tx: + * + * operations follow producer-consumer paradigm, with the hw + * in the middle doing the processing. + * ring size must be power of two. + * + * producer advances r->tail after inserting for processing + * consumer advances r->head after removing processed rd + * ring is empty if head==tail / full if (tail+1)==head + */ + +struct vlsi_ring { + struct pci_dev *pdev; + int dir; + unsigned len; + unsigned size; + unsigned mask; + atomic_t head, tail; + struct ring_descr *rd; +}; + +/* ring processing helpers */ + +static inline struct ring_descr *ring_last(struct vlsi_ring *r) +{ + int t; + + t = atomic_read(&r->tail) & r->mask; + return (((t+1) & r->mask) == (atomic_read(&r->head) & r->mask)) ? NULL : &r->rd[t]; +} + +static inline struct ring_descr *ring_put(struct vlsi_ring *r) +{ + atomic_inc(&r->tail); + return ring_last(r); +} + +static inline struct ring_descr *ring_first(struct vlsi_ring *r) +{ + int h; + + h = atomic_read(&r->head) & r->mask; + return (h == (atomic_read(&r->tail) & r->mask)) ? NULL : &r->rd[h]; +} + +static inline struct ring_descr *ring_get(struct vlsi_ring *r) +{ + atomic_inc(&r->head); + return ring_first(r); +} + +/******************************************************************/ + +/* our private compound VLSI-PCI-IRDA device information */ + +typedef struct vlsi_irda_dev { + struct pci_dev *pdev; + struct net_device_stats stats; + + struct irlap_cb *irlap; + + struct qos_info qos; + + unsigned mode; + int baud, new_baud; + + dma_addr_t busaddr; + void *virtaddr; + struct vlsi_ring *tx_ring, *rx_ring; + + struct timeval last_rx; + + spinlock_t lock; + struct semaphore sem; + + u8 resume_ok; + struct proc_dir_entry *proc_entry; + +} vlsi_irda_dev_t; + +/********************************************************/ + +/* the remapped error flags we use for returning from frame + * post-processing in vlsi_process_tx/rx() after it was completed + * by the hardware. These functions either return the >=0 number + * of transfered bytes in case of success or the negative (-) + * of the or'ed error flags. + */ + +#define VLSI_TX_DROP 0x0001 +#define VLSI_TX_FIFO 0x0002 + +#define VLSI_RX_DROP 0x0100 +#define VLSI_RX_OVER 0x0200 +#define VLSI_RX_LENGTH 0x0400 +#define VLSI_RX_FRAME 0x0800 +#define VLSI_RX_CRC 0x1000 + +/********************************************************/ + +#endif /* IRDA_VLSI_FIR_H */ + |