diff options
Diffstat (limited to 'drivers/net/ethernet/intel/igb/e1000_phy.c')
| -rw-r--r-- | drivers/net/ethernet/intel/igb/e1000_phy.c | 2347 |
1 files changed, 2347 insertions, 0 deletions
diff --git a/drivers/net/ethernet/intel/igb/e1000_phy.c b/drivers/net/ethernet/intel/igb/e1000_phy.c new file mode 100644 index 00000000000..7edf31efe75 --- /dev/null +++ b/drivers/net/ethernet/intel/igb/e1000_phy.c @@ -0,0 +1,2347 @@ +/******************************************************************************* + + Intel(R) Gigabit Ethernet Linux driver + Copyright(c) 2007-2011 Intel Corporation. + + This program is free software; you can redistribute it and/or modify it + under the terms and conditions of the GNU General Public License, + version 2, as published by the Free Software Foundation. + + This program is distributed in the hope it will be useful, but WITHOUT + ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + more details. + + You should have received a copy of the GNU General Public License along with + this program; if not, write to the Free Software Foundation, Inc., + 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. + + The full GNU General Public License is included in this distribution in + the file called "COPYING". + + Contact Information: + e1000-devel Mailing List <e1000-devel@lists.sourceforge.net> + Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 + +*******************************************************************************/ + +#include <linux/if_ether.h> +#include <linux/delay.h> + +#include "e1000_mac.h" +#include "e1000_phy.h" + +static s32 igb_phy_setup_autoneg(struct e1000_hw *hw); +static void igb_phy_force_speed_duplex_setup(struct e1000_hw *hw, + u16 *phy_ctrl); +static s32 igb_wait_autoneg(struct e1000_hw *hw); + +/* Cable length tables */ +static const u16 e1000_m88_cable_length_table[] = + { 0, 50, 80, 110, 140, 140, E1000_CABLE_LENGTH_UNDEFINED }; +#define M88E1000_CABLE_LENGTH_TABLE_SIZE \ + (sizeof(e1000_m88_cable_length_table) / \ + sizeof(e1000_m88_cable_length_table[0])) + +static const u16 e1000_igp_2_cable_length_table[] = + { 0, 0, 0, 0, 0, 0, 0, 0, 3, 5, 8, 11, 13, 16, 18, 21, + 0, 0, 0, 3, 6, 10, 13, 16, 19, 23, 26, 29, 32, 35, 38, 41, + 6, 10, 14, 18, 22, 26, 30, 33, 37, 41, 44, 48, 51, 54, 58, 61, + 21, 26, 31, 35, 40, 44, 49, 53, 57, 61, 65, 68, 72, 75, 79, 82, + 40, 45, 51, 56, 61, 66, 70, 75, 79, 83, 87, 91, 94, 98, 101, 104, + 60, 66, 72, 77, 82, 87, 92, 96, 100, 104, 108, 111, 114, 117, 119, 121, + 83, 89, 95, 100, 105, 109, 113, 116, 119, 122, 124, + 104, 109, 114, 118, 121, 124}; +#define IGP02E1000_CABLE_LENGTH_TABLE_SIZE \ + (sizeof(e1000_igp_2_cable_length_table) / \ + sizeof(e1000_igp_2_cable_length_table[0])) + +/** + * igb_check_reset_block - Check if PHY reset is blocked + * @hw: pointer to the HW structure + * + * Read the PHY management control register and check whether a PHY reset + * is blocked. If a reset is not blocked return 0, otherwise + * return E1000_BLK_PHY_RESET (12). + **/ +s32 igb_check_reset_block(struct e1000_hw *hw) +{ + u32 manc; + + manc = rd32(E1000_MANC); + + return (manc & E1000_MANC_BLK_PHY_RST_ON_IDE) ? + E1000_BLK_PHY_RESET : 0; +} + +/** + * igb_get_phy_id - Retrieve the PHY ID and revision + * @hw: pointer to the HW structure + * + * Reads the PHY registers and stores the PHY ID and possibly the PHY + * revision in the hardware structure. + **/ +s32 igb_get_phy_id(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val = 0; + u16 phy_id; + + ret_val = phy->ops.read_reg(hw, PHY_ID1, &phy_id); + if (ret_val) + goto out; + + phy->id = (u32)(phy_id << 16); + udelay(20); + ret_val = phy->ops.read_reg(hw, PHY_ID2, &phy_id); + if (ret_val) + goto out; + + phy->id |= (u32)(phy_id & PHY_REVISION_MASK); + phy->revision = (u32)(phy_id & ~PHY_REVISION_MASK); + +out: + return ret_val; +} + +/** + * igb_phy_reset_dsp - Reset PHY DSP + * @hw: pointer to the HW structure + * + * Reset the digital signal processor. + **/ +static s32 igb_phy_reset_dsp(struct e1000_hw *hw) +{ + s32 ret_val = 0; + + if (!(hw->phy.ops.write_reg)) + goto out; + + ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xC1); + if (ret_val) + goto out; + + ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_GEN_CONTROL, 0); + +out: + return ret_val; +} + +/** + * igb_read_phy_reg_mdic - Read MDI control register + * @hw: pointer to the HW structure + * @offset: register offset to be read + * @data: pointer to the read data + * + * Reads the MDI control regsiter in the PHY at offset and stores the + * information read to data. + **/ +s32 igb_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data) +{ + struct e1000_phy_info *phy = &hw->phy; + u32 i, mdic = 0; + s32 ret_val = 0; + + if (offset > MAX_PHY_REG_ADDRESS) { + hw_dbg("PHY Address %d is out of range\n", offset); + ret_val = -E1000_ERR_PARAM; + goto out; + } + + /* + * Set up Op-code, Phy Address, and register offset in the MDI + * Control register. The MAC will take care of interfacing with the + * PHY to retrieve the desired data. + */ + mdic = ((offset << E1000_MDIC_REG_SHIFT) | + (phy->addr << E1000_MDIC_PHY_SHIFT) | + (E1000_MDIC_OP_READ)); + + wr32(E1000_MDIC, mdic); + + /* + * Poll the ready bit to see if the MDI read completed + * Increasing the time out as testing showed failures with + * the lower time out + */ + for (i = 0; i < (E1000_GEN_POLL_TIMEOUT * 3); i++) { + udelay(50); + mdic = rd32(E1000_MDIC); + if (mdic & E1000_MDIC_READY) + break; + } + if (!(mdic & E1000_MDIC_READY)) { + hw_dbg("MDI Read did not complete\n"); + ret_val = -E1000_ERR_PHY; + goto out; + } + if (mdic & E1000_MDIC_ERROR) { + hw_dbg("MDI Error\n"); + ret_val = -E1000_ERR_PHY; + goto out; + } + *data = (u16) mdic; + +out: + return ret_val; +} + +/** + * igb_write_phy_reg_mdic - Write MDI control register + * @hw: pointer to the HW structure + * @offset: register offset to write to + * @data: data to write to register at offset + * + * Writes data to MDI control register in the PHY at offset. + **/ +s32 igb_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data) +{ + struct e1000_phy_info *phy = &hw->phy; + u32 i, mdic = 0; + s32 ret_val = 0; + + if (offset > MAX_PHY_REG_ADDRESS) { + hw_dbg("PHY Address %d is out of range\n", offset); + ret_val = -E1000_ERR_PARAM; + goto out; + } + + /* + * Set up Op-code, Phy Address, and register offset in the MDI + * Control register. The MAC will take care of interfacing with the + * PHY to retrieve the desired data. + */ + mdic = (((u32)data) | + (offset << E1000_MDIC_REG_SHIFT) | + (phy->addr << E1000_MDIC_PHY_SHIFT) | + (E1000_MDIC_OP_WRITE)); + + wr32(E1000_MDIC, mdic); + + /* + * Poll the ready bit to see if the MDI read completed + * Increasing the time out as testing showed failures with + * the lower time out + */ + for (i = 0; i < (E1000_GEN_POLL_TIMEOUT * 3); i++) { + udelay(50); + mdic = rd32(E1000_MDIC); + if (mdic & E1000_MDIC_READY) + break; + } + if (!(mdic & E1000_MDIC_READY)) { + hw_dbg("MDI Write did not complete\n"); + ret_val = -E1000_ERR_PHY; + goto out; + } + if (mdic & E1000_MDIC_ERROR) { + hw_dbg("MDI Error\n"); + ret_val = -E1000_ERR_PHY; + goto out; + } + +out: + return ret_val; +} + +/** + * igb_read_phy_reg_i2c - Read PHY register using i2c + * @hw: pointer to the HW structure + * @offset: register offset to be read + * @data: pointer to the read data + * + * Reads the PHY register at offset using the i2c interface and stores the + * retrieved information in data. + **/ +s32 igb_read_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 *data) +{ + struct e1000_phy_info *phy = &hw->phy; + u32 i, i2ccmd = 0; + + + /* + * Set up Op-code, Phy Address, and register address in the I2CCMD + * register. The MAC will take care of interfacing with the + * PHY to retrieve the desired data. + */ + i2ccmd = ((offset << E1000_I2CCMD_REG_ADDR_SHIFT) | + (phy->addr << E1000_I2CCMD_PHY_ADDR_SHIFT) | + (E1000_I2CCMD_OPCODE_READ)); + + wr32(E1000_I2CCMD, i2ccmd); + + /* Poll the ready bit to see if the I2C read completed */ + for (i = 0; i < E1000_I2CCMD_PHY_TIMEOUT; i++) { + udelay(50); + i2ccmd = rd32(E1000_I2CCMD); + if (i2ccmd & E1000_I2CCMD_READY) + break; + } + if (!(i2ccmd & E1000_I2CCMD_READY)) { + hw_dbg("I2CCMD Read did not complete\n"); + return -E1000_ERR_PHY; + } + if (i2ccmd & E1000_I2CCMD_ERROR) { + hw_dbg("I2CCMD Error bit set\n"); + return -E1000_ERR_PHY; + } + + /* Need to byte-swap the 16-bit value. */ + *data = ((i2ccmd >> 8) & 0x00FF) | ((i2ccmd << 8) & 0xFF00); + + return 0; +} + +/** + * igb_write_phy_reg_i2c - Write PHY register using i2c + * @hw: pointer to the HW structure + * @offset: register offset to write to + * @data: data to write at register offset + * + * Writes the data to PHY register at the offset using the i2c interface. + **/ +s32 igb_write_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 data) +{ + struct e1000_phy_info *phy = &hw->phy; + u32 i, i2ccmd = 0; + u16 phy_data_swapped; + + /* Prevent overwritting SFP I2C EEPROM which is at A0 address.*/ + if ((hw->phy.addr == 0) || (hw->phy.addr > 7)) { + hw_dbg("PHY I2C Address %d is out of range.\n", + hw->phy.addr); + return -E1000_ERR_CONFIG; + } + + /* Swap the data bytes for the I2C interface */ + phy_data_swapped = ((data >> 8) & 0x00FF) | ((data << 8) & 0xFF00); + + /* + * Set up Op-code, Phy Address, and register address in the I2CCMD + * register. The MAC will take care of interfacing with the + * PHY to retrieve the desired data. + */ + i2ccmd = ((offset << E1000_I2CCMD_REG_ADDR_SHIFT) | + (phy->addr << E1000_I2CCMD_PHY_ADDR_SHIFT) | + E1000_I2CCMD_OPCODE_WRITE | + phy_data_swapped); + + wr32(E1000_I2CCMD, i2ccmd); + + /* Poll the ready bit to see if the I2C read completed */ + for (i = 0; i < E1000_I2CCMD_PHY_TIMEOUT; i++) { + udelay(50); + i2ccmd = rd32(E1000_I2CCMD); + if (i2ccmd & E1000_I2CCMD_READY) + break; + } + if (!(i2ccmd & E1000_I2CCMD_READY)) { + hw_dbg("I2CCMD Write did not complete\n"); + return -E1000_ERR_PHY; + } + if (i2ccmd & E1000_I2CCMD_ERROR) { + hw_dbg("I2CCMD Error bit set\n"); + return -E1000_ERR_PHY; + } + + return 0; +} + +/** + * igb_read_phy_reg_igp - Read igp PHY register + * @hw: pointer to the HW structure + * @offset: register offset to be read + * @data: pointer to the read data + * + * Acquires semaphore, if necessary, then reads the PHY register at offset + * and storing the retrieved information in data. Release any acquired + * semaphores before exiting. + **/ +s32 igb_read_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 *data) +{ + s32 ret_val = 0; + + if (!(hw->phy.ops.acquire)) + goto out; + + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + goto out; + + if (offset > MAX_PHY_MULTI_PAGE_REG) { + ret_val = igb_write_phy_reg_mdic(hw, + IGP01E1000_PHY_PAGE_SELECT, + (u16)offset); + if (ret_val) { + hw->phy.ops.release(hw); + goto out; + } + } + + ret_val = igb_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset, + data); + + hw->phy.ops.release(hw); + +out: + return ret_val; +} + +/** + * igb_write_phy_reg_igp - Write igp PHY register + * @hw: pointer to the HW structure + * @offset: register offset to write to + * @data: data to write at register offset + * + * Acquires semaphore, if necessary, then writes the data to PHY register + * at the offset. Release any acquired semaphores before exiting. + **/ +s32 igb_write_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 data) +{ + s32 ret_val = 0; + + if (!(hw->phy.ops.acquire)) + goto out; + + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + goto out; + + if (offset > MAX_PHY_MULTI_PAGE_REG) { + ret_val = igb_write_phy_reg_mdic(hw, + IGP01E1000_PHY_PAGE_SELECT, + (u16)offset); + if (ret_val) { + hw->phy.ops.release(hw); + goto out; + } + } + + ret_val = igb_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset, + data); + + hw->phy.ops.release(hw); + +out: + return ret_val; +} + +/** + * igb_copper_link_setup_82580 - Setup 82580 PHY for copper link + * @hw: pointer to the HW structure + * + * Sets up Carrier-sense on Transmit and downshift values. + **/ +s32 igb_copper_link_setup_82580(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 phy_data; + + + if (phy->reset_disable) { + ret_val = 0; + goto out; + } + + if (phy->type == e1000_phy_82580) { + ret_val = hw->phy.ops.reset(hw); + if (ret_val) { + hw_dbg("Error resetting the PHY.\n"); + goto out; + } + } + + /* Enable CRS on TX. This must be set for half-duplex operation. */ + ret_val = phy->ops.read_reg(hw, I82580_CFG_REG, &phy_data); + if (ret_val) + goto out; + + phy_data |= I82580_CFG_ASSERT_CRS_ON_TX; + + /* Enable downshift */ + phy_data |= I82580_CFG_ENABLE_DOWNSHIFT; + + ret_val = phy->ops.write_reg(hw, I82580_CFG_REG, phy_data); + +out: + return ret_val; +} + +/** + * igb_copper_link_setup_m88 - Setup m88 PHY's for copper link + * @hw: pointer to the HW structure + * + * Sets up MDI/MDI-X and polarity for m88 PHY's. If necessary, transmit clock + * and downshift values are set also. + **/ +s32 igb_copper_link_setup_m88(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 phy_data; + + if (phy->reset_disable) { + ret_val = 0; + goto out; + } + + /* Enable CRS on TX. This must be set for half-duplex operation. */ + ret_val = phy->ops.read_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); + if (ret_val) + goto out; + + phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX; + + /* + * Options: + * MDI/MDI-X = 0 (default) + * 0 - Auto for all speeds + * 1 - MDI mode + * 2 - MDI-X mode + * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes) + */ + phy_data &= ~M88E1000_PSCR_AUTO_X_MODE; + + switch (phy->mdix) { + case 1: + phy_data |= M88E1000_PSCR_MDI_MANUAL_MODE; + break; + case 2: + phy_data |= M88E1000_PSCR_MDIX_MANUAL_MODE; + break; + case 3: + phy_data |= M88E1000_PSCR_AUTO_X_1000T; + break; + case 0: + default: + phy_data |= M88E1000_PSCR_AUTO_X_MODE; + break; + } + + /* + * Options: + * disable_polarity_correction = 0 (default) + * Automatic Correction for Reversed Cable Polarity + * 0 - Disabled + * 1 - Enabled + */ + phy_data &= ~M88E1000_PSCR_POLARITY_REVERSAL; + if (phy->disable_polarity_correction == 1) + phy_data |= M88E1000_PSCR_POLARITY_REVERSAL; + + ret_val = phy->ops.write_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data); + if (ret_val) + goto out; + + if (phy->revision < E1000_REVISION_4) { + /* + * Force TX_CLK in the Extended PHY Specific Control Register + * to 25MHz clock. + */ + ret_val = phy->ops.read_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, + &phy_data); + if (ret_val) + goto out; + + phy_data |= M88E1000_EPSCR_TX_CLK_25; + + if ((phy->revision == E1000_REVISION_2) && + (phy->id == M88E1111_I_PHY_ID)) { + /* 82573L PHY - set the downshift counter to 5x. */ + phy_data &= ~M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK; + phy_data |= M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X; + } else { + /* Configure Master and Slave downshift values */ + phy_data &= ~(M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK | + M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK); + phy_data |= (M88E1000_EPSCR_MASTER_DOWNSHIFT_1X | + M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X); + } + ret_val = phy->ops.write_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, + phy_data); + if (ret_val) + goto out; + } + + /* Commit the changes. */ + ret_val = igb_phy_sw_reset(hw); + if (ret_val) { + hw_dbg("Error committing the PHY changes\n"); + goto out; + } + +out: + return ret_val; +} + +/** + * igb_copper_link_setup_m88_gen2 - Setup m88 PHY's for copper link + * @hw: pointer to the HW structure + * + * Sets up MDI/MDI-X and polarity for i347-AT4, m88e1322 and m88e1112 PHY's. + * Also enables and sets the downshift parameters. + **/ +s32 igb_copper_link_setup_m88_gen2(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 phy_data; + + if (phy->reset_disable) { + ret_val = 0; + goto out; + } + + /* Enable CRS on Tx. This must be set for half-duplex operation. */ + ret_val = phy->ops.read_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); + if (ret_val) + goto out; + + /* + * Options: + * MDI/MDI-X = 0 (default) + * 0 - Auto for all speeds + * 1 - MDI mode + * 2 - MDI-X mode + * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes) + */ + phy_data &= ~M88E1000_PSCR_AUTO_X_MODE; + + switch (phy->mdix) { + case 1: + phy_data |= M88E1000_PSCR_MDI_MANUAL_MODE; + break; + case 2: + phy_data |= M88E1000_PSCR_MDIX_MANUAL_MODE; + break; + case 3: + /* M88E1112 does not support this mode) */ + if (phy->id != M88E1112_E_PHY_ID) { + phy_data |= M88E1000_PSCR_AUTO_X_1000T; + break; + } + case 0: + default: + phy_data |= M88E1000_PSCR_AUTO_X_MODE; + break; + } + + /* + * Options: + * disable_polarity_correction = 0 (default) + * Automatic Correction for Reversed Cable Polarity + * 0 - Disabled + * 1 - Enabled + */ + phy_data &= ~M88E1000_PSCR_POLARITY_REVERSAL; + if (phy->disable_polarity_correction == 1) + phy_data |= M88E1000_PSCR_POLARITY_REVERSAL; + + /* Enable downshift and setting it to X6 */ + phy_data &= ~I347AT4_PSCR_DOWNSHIFT_MASK; + phy_data |= I347AT4_PSCR_DOWNSHIFT_6X; + phy_data |= I347AT4_PSCR_DOWNSHIFT_ENABLE; + + ret_val = phy->ops.write_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data); + if (ret_val) + goto out; + + /* Commit the changes. */ + ret_val = igb_phy_sw_reset(hw); + if (ret_val) { + hw_dbg("Error committing the PHY changes\n"); + goto out; + } + +out: + return ret_val; +} + +/** + * igb_copper_link_setup_igp - Setup igp PHY's for copper link + * @hw: pointer to the HW structure + * + * Sets up LPLU, MDI/MDI-X, polarity, Smartspeed and Master/Slave config for + * igp PHY's. + **/ +s32 igb_copper_link_setup_igp(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 data; + + if (phy->reset_disable) { + ret_val = 0; + goto out; + } + + ret_val = phy->ops.reset(hw); + if (ret_val) { + hw_dbg("Error resetting the PHY.\n"); + goto out; + } + + /* + * Wait 100ms for MAC to configure PHY from NVM settings, to avoid + * timeout issues when LFS is enabled. + */ + msleep(100); + + /* + * The NVM settings will configure LPLU in D3 for + * non-IGP1 PHYs. + */ + if (phy->type == e1000_phy_igp) { + /* disable lplu d3 during driver init */ + if (phy->ops.set_d3_lplu_state) + ret_val = phy->ops.set_d3_lplu_state(hw, false); + if (ret_val) { + hw_dbg("Error Disabling LPLU D3\n"); + goto out; + } + } + + /* disable lplu d0 during driver init */ + ret_val = phy->ops.set_d0_lplu_state(hw, false); + if (ret_val) { + hw_dbg("Error Disabling LPLU D0\n"); + goto out; + } + /* Configure mdi-mdix settings */ + ret_val = phy->ops.read_reg(hw, IGP01E1000_PHY_PORT_CTRL, &data); + if (ret_val) + goto out; + + data &= ~IGP01E1000_PSCR_AUTO_MDIX; + + switch (phy->mdix) { + case 1: + data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX; + break; + case 2: + data |= IGP01E1000_PSCR_FORCE_MDI_MDIX; + break; + case 0: + default: + data |= IGP01E1000_PSCR_AUTO_MDIX; + break; + } + ret_val = phy->ops.write_reg(hw, IGP01E1000_PHY_PORT_CTRL, data); + if (ret_val) + goto out; + + /* set auto-master slave resolution settings */ + if (hw->mac.autoneg) { + /* + * when autonegotiation advertisement is only 1000Mbps then we + * should disable SmartSpeed and enable Auto MasterSlave + * resolution as hardware default. + */ + if (phy->autoneg_advertised == ADVERTISE_1000_FULL) { + /* Disable SmartSpeed */ + ret_val = phy->ops.read_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + &data); + if (ret_val) + goto out; + + data &= ~IGP01E1000_PSCFR_SMART_SPEED; + ret_val = phy->ops.write_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + data); + if (ret_val) + goto out; + + /* Set auto Master/Slave resolution process */ + ret_val = phy->ops.read_reg(hw, PHY_1000T_CTRL, &data); + if (ret_val) + goto out; + + data &= ~CR_1000T_MS_ENABLE; + ret_val = phy->ops.write_reg(hw, PHY_1000T_CTRL, data); + if (ret_val) + goto out; + } + + ret_val = phy->ops.read_reg(hw, PHY_1000T_CTRL, &data); + if (ret_val) + goto out; + + /* load defaults for future use */ + phy->original_ms_type = (data & CR_1000T_MS_ENABLE) ? + ((data & CR_1000T_MS_VALUE) ? + e1000_ms_force_master : + e1000_ms_force_slave) : + e1000_ms_auto; + + switch (phy->ms_type) { + case e1000_ms_force_master: + data |= (CR_1000T_MS_ENABLE | CR_1000T_MS_VALUE); + break; + case e1000_ms_force_slave: + data |= CR_1000T_MS_ENABLE; + data &= ~(CR_1000T_MS_VALUE); + break; + case e1000_ms_auto: + data &= ~CR_1000T_MS_ENABLE; + default: + break; + } + ret_val = phy->ops.write_reg(hw, PHY_1000T_CTRL, data); + if (ret_val) + goto out; + } + +out: + return ret_val; +} + +/** + * igb_copper_link_autoneg - Setup/Enable autoneg for copper link + * @hw: pointer to the HW structure + * + * Performs initial bounds checking on autoneg advertisement parameter, then + * configure to advertise the full capability. Setup the PHY to autoneg + * and restart the negotiation process between the link partner. If + * autoneg_wait_to_complete, then wait for autoneg to complete before exiting. + **/ +static s32 igb_copper_link_autoneg(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 phy_ctrl; + + /* + * Perform some bounds checking on the autoneg advertisement + * parameter. + */ + phy->autoneg_advertised &= phy->autoneg_mask; + + /* + * If autoneg_advertised is zero, we assume it was not defaulted + * by the calling code so we set to advertise full capability. + */ + if (phy->autoneg_advertised == 0) + phy->autoneg_advertised = phy->autoneg_mask; + + hw_dbg("Reconfiguring auto-neg advertisement params\n"); + ret_val = igb_phy_setup_autoneg(hw); + if (ret_val) { + hw_dbg("Error Setting up Auto-Negotiation\n"); + goto out; + } + hw_dbg("Restarting Auto-Neg\n"); + + /* + * Restart auto-negotiation by setting the Auto Neg Enable bit and + * the Auto Neg Restart bit in the PHY control register. + */ + ret_val = phy->ops.read_reg(hw, PHY_CONTROL, &phy_ctrl); + if (ret_val) + goto out; + + phy_ctrl |= (MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG); + ret_val = phy->ops.write_reg(hw, PHY_CONTROL, phy_ctrl); + if (ret_val) + goto out; + + /* + * Does the user want to wait for Auto-Neg to complete here, or + * check at a later time (for example, callback routine). + */ + if (phy->autoneg_wait_to_complete) { + ret_val = igb_wait_autoneg(hw); + if (ret_val) { + hw_dbg("Error while waiting for " + "autoneg to complete\n"); + goto out; + } + } + + hw->mac.get_link_status = true; + +out: + return ret_val; +} + +/** + * igb_phy_setup_autoneg - Configure PHY for auto-negotiation + * @hw: pointer to the HW structure + * + * Reads the MII auto-neg advertisement register and/or the 1000T control + * register and if the PHY is already setup for auto-negotiation, then + * return successful. Otherwise, setup advertisement and flow control to + * the appropriate values for the wanted auto-negotiation. + **/ +static s32 igb_phy_setup_autoneg(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 mii_autoneg_adv_reg; + u16 mii_1000t_ctrl_reg = 0; + + phy->autoneg_advertised &= phy->autoneg_mask; + + /* Read the MII Auto-Neg Advertisement Register (Address 4). */ + ret_val = phy->ops.read_reg(hw, PHY_AUTONEG_ADV, &mii_autoneg_adv_reg); + if (ret_val) + goto out; + + if (phy->autoneg_mask & ADVERTISE_1000_FULL) { + /* Read the MII 1000Base-T Control Register (Address 9). */ + ret_val = phy->ops.read_reg(hw, PHY_1000T_CTRL, + &mii_1000t_ctrl_reg); + if (ret_val) + goto out; + } + + /* + * Need to parse both autoneg_advertised and fc and set up + * the appropriate PHY registers. First we will parse for + * autoneg_advertised software override. Since we can advertise + * a plethora of combinations, we need to check each bit + * individually. + */ + + /* + * First we clear all the 10/100 mb speed bits in the Auto-Neg + * Advertisement Register (Address 4) and the 1000 mb speed bits in + * the 1000Base-T Control Register (Address 9). + */ + mii_autoneg_adv_reg &= ~(NWAY_AR_100TX_FD_CAPS | + NWAY_AR_100TX_HD_CAPS | + NWAY_AR_10T_FD_CAPS | + NWAY_AR_10T_HD_CAPS); + mii_1000t_ctrl_reg &= ~(CR_1000T_HD_CAPS | CR_1000T_FD_CAPS); + + hw_dbg("autoneg_advertised %x\n", phy->autoneg_advertised); + + /* Do we want to advertise 10 Mb Half Duplex? */ + if (phy->autoneg_advertised & ADVERTISE_10_HALF) { + hw_dbg("Advertise 10mb Half duplex\n"); + mii_autoneg_adv_reg |= NWAY_AR_10T_HD_CAPS; + } + + /* Do we want to advertise 10 Mb Full Duplex? */ + if (phy->autoneg_advertised & ADVERTISE_10_FULL) { + hw_dbg("Advertise 10mb Full duplex\n"); + mii_autoneg_adv_reg |= NWAY_AR_10T_FD_CAPS; + } + + /* Do we want to advertise 100 Mb Half Duplex? */ + if (phy->autoneg_advertised & ADVERTISE_100_HALF) { + hw_dbg("Advertise 100mb Half duplex\n"); + mii_autoneg_adv_reg |= NWAY_AR_100TX_HD_CAPS; + } + + /* Do we want to advertise 100 Mb Full Duplex? */ + if (phy->autoneg_advertised & ADVERTISE_100_FULL) { + hw_dbg("Advertise 100mb Full duplex\n"); + mii_autoneg_adv_reg |= NWAY_AR_100TX_FD_CAPS; + } + + /* We do not allow the Phy to advertise 1000 Mb Half Duplex */ + if (phy->autoneg_advertised & ADVERTISE_1000_HALF) + hw_dbg("Advertise 1000mb Half duplex request denied!\n"); + + /* Do we want to advertise 1000 Mb Full Duplex? */ + if (phy->autoneg_advertised & ADVERTISE_1000_FULL) { + hw_dbg("Advertise 1000mb Full duplex\n"); + mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS; + } + + /* + * Check for a software override of the flow control settings, and + * setup the PHY advertisement registers accordingly. If + * auto-negotiation is enabled, then software will have to set the + * "PAUSE" bits to the correct value in the Auto-Negotiation + * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto- + * negotiation. + * + * The possible values of the "fc" parameter are: + * 0: Flow control is completely disabled + * 1: Rx flow control is enabled (we can receive pause frames + * but not send pause frames). + * 2: Tx flow control is enabled (we can send pause frames + * but we do not support receiving pause frames). + * 3: Both Rx and TX flow control (symmetric) are enabled. + * other: No software override. The flow control configuration + * in the EEPROM is used. + */ + switch (hw->fc.current_mode) { + case e1000_fc_none: + /* + * Flow control (RX & TX) is completely disabled by a + * software over-ride. + */ + mii_autoneg_adv_reg &= ~(NWAY_AR_ASM_DIR | NWAY_AR_PAUSE); + break; + case e1000_fc_rx_pause: + /* + * RX Flow control is enabled, and TX Flow control is + * disabled, by a software over-ride. + * + * Since there really isn't a way to advertise that we are + * capable of RX Pause ONLY, we will advertise that we + * support both symmetric and asymmetric RX PAUSE. Later + * (in e1000_config_fc_after_link_up) we will disable the + * hw's ability to send PAUSE frames. + */ + mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE); + break; + case e1000_fc_tx_pause: + /* + * TX Flow control is enabled, and RX Flow control is + * disabled, by a software over-ride. + */ + mii_autoneg_adv_reg |= NWAY_AR_ASM_DIR; + mii_autoneg_adv_reg &= ~NWAY_AR_PAUSE; + break; + case e1000_fc_full: + /* + * Flow control (both RX and TX) is enabled by a software + * over-ride. + */ + mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE); + break; + default: + hw_dbg("Flow control param set incorrectly\n"); + ret_val = -E1000_ERR_CONFIG; + goto out; + } + + ret_val = phy->ops.write_reg(hw, PHY_AUTONEG_ADV, mii_autoneg_adv_reg); + if (ret_val) + goto out; + + hw_dbg("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg); + + if (phy->autoneg_mask & ADVERTISE_1000_FULL) { + ret_val = phy->ops.write_reg(hw, + PHY_1000T_CTRL, + mii_1000t_ctrl_reg); + if (ret_val) + goto out; + } + +out: + return ret_val; +} + +/** + * igb_setup_copper_link - Configure copper link settings + * @hw: pointer to the HW structure + * + * Calls the appropriate function to configure the link for auto-neg or forced + * speed and duplex. Then we check for link, once link is established calls + * to configure collision distance and flow control are called. If link is + * not established, we return -E1000_ERR_PHY (-2). + **/ +s32 igb_setup_copper_link(struct e1000_hw *hw) +{ + s32 ret_val; + bool link; + + + if (hw->mac.autoneg) { + /* + * Setup autoneg and flow control advertisement and perform + * autonegotiation. + */ + ret_val = igb_copper_link_autoneg(hw); + if (ret_val) + goto out; + } else { + /* + * PHY will be set to 10H, 10F, 100H or 100F + * depending on user settings. + */ + hw_dbg("Forcing Speed and Duplex\n"); + ret_val = hw->phy.ops.force_speed_duplex(hw); + if (ret_val) { + hw_dbg("Error Forcing Speed and Duplex\n"); + goto out; + } + } + + /* + * Check link status. Wait up to 100 microseconds for link to become + * valid. + */ + ret_val = igb_phy_has_link(hw, + COPPER_LINK_UP_LIMIT, + 10, + &link); + if (ret_val) + goto out; + + if (link) { + hw_dbg("Valid link established!!!\n"); + igb_config_collision_dist(hw); + ret_val = igb_config_fc_after_link_up(hw); + } else { + hw_dbg("Unable to establish link!!!\n"); + } + +out: + return ret_val; +} + +/** + * igb_phy_force_speed_duplex_igp - Force speed/duplex for igp PHY + * @hw: pointer to the HW structure + * + * Calls the PHY setup function to force speed and duplex. Clears the + * auto-crossover to force MDI manually. Waits for link and returns + * successful if link up is successful, else -E1000_ERR_PHY (-2). + **/ +s32 igb_phy_force_speed_duplex_igp(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 phy_data; + bool link; + + ret_val = phy->ops.read_reg(hw, PHY_CONTROL, &phy_data); + if (ret_val) + goto out; + + igb_phy_force_speed_duplex_setup(hw, &phy_data); + + ret_val = phy->ops.write_reg(hw, PHY_CONTROL, phy_data); + if (ret_val) + goto out; + + /* + * Clear Auto-Crossover to force MDI manually. IGP requires MDI + * forced whenever speed and duplex are forced. + */ + ret_val = phy->ops.read_reg(hw, IGP01E1000_PHY_PORT_CTRL, &phy_data); + if (ret_val) + goto out; + + phy_data &= ~IGP01E1000_PSCR_AUTO_MDIX; + phy_data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX; + + ret_val = phy->ops.write_reg(hw, IGP01E1000_PHY_PORT_CTRL, phy_data); + if (ret_val) + goto out; + + hw_dbg("IGP PSCR: %X\n", phy_data); + + udelay(1); + + if (phy->autoneg_wait_to_complete) { + hw_dbg("Waiting for forced speed/duplex link on IGP phy.\n"); + + ret_val = igb_phy_has_link(hw, + PHY_FORCE_LIMIT, + 100000, + &link); + if (ret_val) + goto out; + + if (!link) + hw_dbg("Link taking longer than expected.\n"); + + /* Try once more */ + ret_val = igb_phy_has_link(hw, + PHY_FORCE_LIMIT, + 100000, + &link); + if (ret_val) + goto out; + } + +out: + return ret_val; +} + +/** + * igb_phy_force_speed_duplex_m88 - Force speed/duplex for m88 PHY + * @hw: pointer to the HW structure + * + * Calls the PHY setup function to force speed and duplex. Clears the + * auto-crossover to force MDI manually. Resets the PHY to commit the + * changes. If time expires while waiting for link up, we reset the DSP. + * After reset, TX_CLK and CRS on TX must be set. Return successful upon + * successful completion, else return corresponding error code. + **/ +s32 igb_phy_force_speed_duplex_m88(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 phy_data; + bool link; + + /* + * Clear Auto-Crossover to force MDI manually. M88E1000 requires MDI + * forced whenever speed and duplex are forced. + */ + ret_val = phy->ops.read_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); + if (ret_val) + goto out; + + phy_data &= ~M88E1000_PSCR_AUTO_X_MODE; + ret_val = phy->ops.write_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data); + if (ret_val) + goto out; + + hw_dbg("M88E1000 PSCR: %X\n", phy_data); + + ret_val = phy->ops.read_reg(hw, PHY_CONTROL, &phy_data); + if (ret_val) + goto out; + + igb_phy_force_speed_duplex_setup(hw, &phy_data); + + ret_val = phy->ops.write_reg(hw, PHY_CONTROL, phy_data); + if (ret_val) + goto out; + + /* Reset the phy to commit changes. */ + ret_val = igb_phy_sw_reset(hw); + if (ret_val) + goto out; + + if (phy->autoneg_wait_to_complete) { + hw_dbg("Waiting for forced speed/duplex link on M88 phy.\n"); + + ret_val = igb_phy_has_link(hw, PHY_FORCE_LIMIT, 100000, &link); + if (ret_val) + goto out; + + if (!link) { + if (hw->phy.type != e1000_phy_m88 || + hw->phy.id == I347AT4_E_PHY_ID || + hw->phy.id == M88E1112_E_PHY_ID) { + hw_dbg("Link taking longer than expected.\n"); + } else { + + /* + * We didn't get link. + * Reset the DSP and cross our fingers. + */ + ret_val = phy->ops.write_reg(hw, + M88E1000_PHY_PAGE_SELECT, + 0x001d); + if (ret_val) + goto out; + ret_val = igb_phy_reset_dsp(hw); + if (ret_val) + goto out; + } + } + + /* Try once more */ + ret_val = igb_phy_has_link(hw, PHY_FORCE_LIMIT, + 100000, &link); + if (ret_val) + goto out; + } + + if (hw->phy.type != e1000_phy_m88 || + hw->phy.id == I347AT4_E_PHY_ID || + hw->phy.id == M88E1112_E_PHY_ID) + goto out; + + ret_val = phy->ops.read_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_data); + if (ret_val) + goto out; + + /* + * Resetting the phy means we need to re-force TX_CLK in the + * Extended PHY Specific Control Register to 25MHz clock from + * the reset value of 2.5MHz. + */ + phy_data |= M88E1000_EPSCR_TX_CLK_25; + ret_val = phy->ops.write_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, phy_data); + if (ret_val) + goto out; + + /* + * In addition, we must re-enable CRS on Tx for both half and full + * duplex. + */ + ret_val = phy->ops.read_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); + if (ret_val) + goto out; + + phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX; + ret_val = phy->ops.write_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data); + +out: + return ret_val; +} + +/** + * igb_phy_force_speed_duplex_setup - Configure forced PHY speed/duplex + * @hw: pointer to the HW structure + * @phy_ctrl: pointer to current value of PHY_CONTROL + * + * Forces speed and duplex on the PHY by doing the following: disable flow + * control, force speed/duplex on the MAC, disable auto speed detection, + * disable auto-negotiation, configure duplex, configure speed, configure + * the collision distance, write configuration to CTRL register. The + * caller must write to the PHY_CONTROL register for these settings to + * take affect. + **/ +static void igb_phy_force_speed_duplex_setup(struct e1000_hw *hw, + u16 *phy_ctrl) +{ + struct e1000_mac_info *mac = &hw->mac; + u32 ctrl; + + /* Turn off flow control when forcing speed/duplex */ + hw->fc.current_mode = e1000_fc_none; + + /* Force speed/duplex on the mac */ + ctrl = rd32(E1000_CTRL); + ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); + ctrl &= ~E1000_CTRL_SPD_SEL; + + /* Disable Auto Speed Detection */ + ctrl &= ~E1000_CTRL_ASDE; + + /* Disable autoneg on the phy */ + *phy_ctrl &= ~MII_CR_AUTO_NEG_EN; + + /* Forcing Full or Half Duplex? */ + if (mac->forced_speed_duplex & E1000_ALL_HALF_DUPLEX) { + ctrl &= ~E1000_CTRL_FD; + *phy_ctrl &= ~MII_CR_FULL_DUPLEX; + hw_dbg("Half Duplex\n"); + } else { + ctrl |= E1000_CTRL_FD; + *phy_ctrl |= MII_CR_FULL_DUPLEX; + hw_dbg("Full Duplex\n"); + } + + /* Forcing 10mb or 100mb? */ + if (mac->forced_speed_duplex & E1000_ALL_100_SPEED) { + ctrl |= E1000_CTRL_SPD_100; + *phy_ctrl |= MII_CR_SPEED_100; + *phy_ctrl &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_10); + hw_dbg("Forcing 100mb\n"); + } else { + ctrl &= ~(E1000_CTRL_SPD_1000 | E1000_CTRL_SPD_100); + *phy_ctrl |= MII_CR_SPEED_10; + *phy_ctrl &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_100); + hw_dbg("Forcing 10mb\n"); + } + + igb_config_collision_dist(hw); + + wr32(E1000_CTRL, ctrl); +} + +/** + * igb_set_d3_lplu_state - Sets low power link up state for D3 + * @hw: pointer to the HW structure + * @active: boolean used to enable/disable lplu + * + * Success returns 0, Failure returns 1 + * + * The low power link up (lplu) state is set to the power management level D3 + * and SmartSpeed is disabled when active is true, else clear lplu for D3 + * and enable Smartspeed. LPLU and Smartspeed are mutually exclusive. LPLU + * is used during Dx states where the power conservation is most important. + * During driver activity, SmartSpeed should be enabled so performance is + * maintained. + **/ +s32 igb_set_d3_lplu_state(struct e1000_hw *hw, bool active) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val = 0; + u16 data; + + if (!(hw->phy.ops.read_reg)) + goto out; + + ret_val = phy->ops.read_reg(hw, IGP02E1000_PHY_POWER_MGMT, &data); + if (ret_val) + goto out; + + if (!active) { + data &= ~IGP02E1000_PM_D3_LPLU; + ret_val = phy->ops.write_reg(hw, IGP02E1000_PHY_POWER_MGMT, + data); + if (ret_val) + goto out; + /* + * LPLU and SmartSpeed are mutually exclusive. LPLU is used + * during Dx states where the power conservation is most + * important. During driver activity we should enable + * SmartSpeed, so performance is maintained. + */ + if (phy->smart_speed == e1000_smart_speed_on) { + ret_val = phy->ops.read_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + &data); + if (ret_val) + goto out; + + data |= IGP01E1000_PSCFR_SMART_SPEED; + ret_val = phy->ops.write_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + data); + if (ret_val) + goto out; + } else if (phy->smart_speed == e1000_smart_speed_off) { + ret_val = phy->ops.read_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + &data); + if (ret_val) + goto out; + + data &= ~IGP01E1000_PSCFR_SMART_SPEED; + ret_val = phy->ops.write_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, + data); + if (ret_val) + goto out; + } + } else if ((phy->autoneg_advertised == E1000_ALL_SPEED_DUPLEX) || + (phy->autoneg_advertised == E1000_ALL_NOT_GIG) || + (phy->autoneg_advertised == E1000_ALL_10_SPEED)) { + data |= IGP02E1000_PM_D3_LPLU; + ret_val = phy->ops.write_reg(hw, IGP02E1000_PHY_POWER_MGMT, + data); + if (ret_val) + goto out; + + /* When LPLU is enabled, we should disable SmartSpeed */ + ret_val = phy->ops.read_reg(hw, IGP01E1000_PHY_PORT_CONFIG, + &data); + if (ret_val) + goto out; + + data &= ~IGP01E1000_PSCFR_SMART_SPEED; + ret_val = phy->ops.write_reg(hw, IGP01E1000_PHY_PORT_CONFIG, + data); + } + +out: + return ret_val; +} + +/** + * igb_check_downshift - Checks whether a downshift in speed occurred + * @hw: pointer to the HW structure + * + * Success returns 0, Failure returns 1 + * + * A downshift is detected by querying the PHY link health. + **/ +s32 igb_check_downshift(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 phy_data, offset, mask; + + switch (phy->type) { + case e1000_phy_m88: + case e1000_phy_gg82563: + offset = M88E1000_PHY_SPEC_STATUS; + mask = M88E1000_PSSR_DOWNSHIFT; + break; + case e1000_phy_igp_2: + case e1000_phy_igp: + case e1000_phy_igp_3: + offset = IGP01E1000_PHY_LINK_HEALTH; + mask = IGP01E1000_PLHR_SS_DOWNGRADE; + break; + default: + /* speed downshift not supported */ + phy->speed_downgraded = false; + ret_val = 0; + goto out; + } + + ret_val = phy->ops.read_reg(hw, offset, &phy_data); + + if (!ret_val) + phy->speed_downgraded = (phy_data & mask) ? true : false; + +out: + return ret_val; +} + +/** + * igb_check_polarity_m88 - Checks the polarity. + * @hw: pointer to the HW structure + * + * Success returns 0, Failure returns -E1000_ERR_PHY (-2) + * + * Polarity is determined based on the PHY specific status register. + **/ +static s32 igb_check_polarity_m88(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 data; + + ret_val = phy->ops.read_reg(hw, M88E1000_PHY_SPEC_STATUS, &data); + + if (!ret_val) + phy->cable_polarity = (data & M88E1000_PSSR_REV_POLARITY) + ? e1000_rev_polarity_reversed + : e1000_rev_polarity_normal; + + return ret_val; +} + +/** + * igb_check_polarity_igp - Checks the polarity. + * @hw: pointer to the HW structure + * + * Success returns 0, Failure returns -E1000_ERR_PHY (-2) + * + * Polarity is determined based on the PHY port status register, and the + * current speed (since there is no polarity at 100Mbps). + **/ +static s32 igb_check_polarity_igp(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 data, offset, mask; + + /* + * Polarity is determined based on the speed of + * our connection. + */ + ret_val = phy->ops.read_reg(hw, IGP01E1000_PHY_PORT_STATUS, &data); + if (ret_val) + goto out; + + if ((data & IGP01E1000_PSSR_SPEED_MASK) == + IGP01E1000_PSSR_SPEED_1000MBPS) { + offset = IGP01E1000_PHY_PCS_INIT_REG; + mask = IGP01E1000_PHY_POLARITY_MASK; + } else { + /* + * This really only applies to 10Mbps since + * there is no polarity for 100Mbps (always 0). + */ + offset = IGP01E1000_PHY_PORT_STATUS; + mask = IGP01E1000_PSSR_POLARITY_REVERSED; + } + + ret_val = phy->ops.read_reg(hw, offset, &data); + + if (!ret_val) + phy->cable_polarity = (data & mask) + ? e1000_rev_polarity_reversed + : e1000_rev_polarity_normal; + +out: + return ret_val; +} + +/** + * igb_wait_autoneg - Wait for auto-neg compeletion + * @hw: pointer to the HW structure + * + * Waits for auto-negotiation to complete or for the auto-negotiation time + * limit to expire, which ever happens first. + **/ +static s32 igb_wait_autoneg(struct e1000_hw *hw) +{ + s32 ret_val = 0; + u16 i, phy_status; + + /* Break after autoneg completes or PHY_AUTO_NEG_LIMIT expires. */ + for (i = PHY_AUTO_NEG_LIMIT; i > 0; i--) { + ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &phy_status); + if (ret_val) + break; + ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &phy_status); + if (ret_val) + break; + if (phy_status & MII_SR_AUTONEG_COMPLETE) + break; + msleep(100); + } + + /* + * PHY_AUTO_NEG_TIME expiration doesn't guarantee auto-negotiation + * has completed. + */ + return ret_val; +} + +/** + * igb_phy_has_link - Polls PHY for link + * @hw: pointer to the HW structure + * @iterations: number of times to poll for link + * @usec_interval: delay between polling attempts + * @success: pointer to whether polling was successful or not + * + * Polls the PHY status register for link, 'iterations' number of times. + **/ +s32 igb_phy_has_link(struct e1000_hw *hw, u32 iterations, + u32 usec_interval, bool *success) +{ + s32 ret_val = 0; + u16 i, phy_status; + + for (i = 0; i < iterations; i++) { + /* + * Some PHYs require the PHY_STATUS register to be read + * twice due to the link bit being sticky. No harm doing + * it across the board. + */ + ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &phy_status); + if (ret_val) { + /* + * If the first read fails, another entity may have + * ownership of the resources, wait and try again to + * see if they have relinquished the resources yet. + */ + udelay(usec_interval); + } + ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &phy_status); + if (ret_val) + break; + if (phy_status & MII_SR_LINK_STATUS) + break; + if (usec_interval >= 1000) + mdelay(usec_interval/1000); + else + udelay(usec_interval); + } + + *success = (i < iterations) ? true : false; + + return ret_val; +} + +/** + * igb_get_cable_length_m88 - Determine cable length for m88 PHY + * @hw: pointer to the HW structure + * + * Reads the PHY specific status register to retrieve the cable length + * information. The cable length is determined by averaging the minimum and + * maximum values to get the "average" cable length. The m88 PHY has four + * possible cable length values, which are: + * Register Value Cable Length + * 0 < 50 meters + * 1 50 - 80 meters + * 2 80 - 110 meters + * 3 110 - 140 meters + * 4 > 140 meters + **/ +s32 igb_get_cable_length_m88(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 phy_data, index; + + ret_val = phy->ops.read_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data); + if (ret_val) + goto out; + + index = (phy_data & M88E1000_PSSR_CABLE_LENGTH) >> + M88E1000_PSSR_CABLE_LENGTH_SHIFT; + if (index >= M88E1000_CABLE_LENGTH_TABLE_SIZE - 1) { + ret_val = -E1000_ERR_PHY; + goto out; + } + + phy->min_cable_length = e1000_m88_cable_length_table[index]; + phy->max_cable_length = e1000_m88_cable_length_table[index + 1]; + + phy->cable_length = (phy->min_cable_length + phy->max_cable_length) / 2; + +out: + return ret_val; +} + +s32 igb_get_cable_length_m88_gen2(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 phy_data, phy_data2, index, default_page, is_cm; + + switch (hw->phy.id) { + case I347AT4_E_PHY_ID: + /* Remember the original page select and set it to 7 */ + ret_val = phy->ops.read_reg(hw, I347AT4_PAGE_SELECT, + &default_page); + if (ret_val) + goto out; + + ret_val = phy->ops.write_reg(hw, I347AT4_PAGE_SELECT, 0x07); + if (ret_val) + goto out; + + /* Get cable length from PHY Cable Diagnostics Control Reg */ + ret_val = phy->ops.read_reg(hw, (I347AT4_PCDL + phy->addr), + &phy_data); + if (ret_val) + goto out; + + /* Check if the unit of cable length is meters or cm */ + ret_val = phy->ops.read_reg(hw, I347AT4_PCDC, &phy_data2); + if (ret_val) + goto out; + + is_cm = !(phy_data & I347AT4_PCDC_CABLE_LENGTH_UNIT); + + /* Populate the phy structure with cable length in meters */ + phy->min_cable_length = phy_data / (is_cm ? 100 : 1); + phy->max_cable_length = phy_data / (is_cm ? 100 : 1); + phy->cable_length = phy_data / (is_cm ? 100 : 1); + + /* Reset the page selec to its original value */ + ret_val = phy->ops.write_reg(hw, I347AT4_PAGE_SELECT, + default_page); + if (ret_val) + goto out; + break; + case M88E1112_E_PHY_ID: + /* Remember the original page select and set it to 5 */ + ret_val = phy->ops.read_reg(hw, I347AT4_PAGE_SELECT, + &default_page); + if (ret_val) + goto out; + + ret_val = phy->ops.write_reg(hw, I347AT4_PAGE_SELECT, 0x05); + if (ret_val) + goto out; + + ret_val = phy->ops.read_reg(hw, M88E1112_VCT_DSP_DISTANCE, + &phy_data); + if (ret_val) + goto out; + + index = (phy_data & M88E1000_PSSR_CABLE_LENGTH) >> + M88E1000_PSSR_CABLE_LENGTH_SHIFT; + if (index >= M88E1000_CABLE_LENGTH_TABLE_SIZE - 1) { + ret_val = -E1000_ERR_PHY; + goto out; + } + + phy->min_cable_length = e1000_m88_cable_length_table[index]; + phy->max_cable_length = e1000_m88_cable_length_table[index + 1]; + + phy->cable_length = (phy->min_cable_length + + phy->max_cable_length) / 2; + + /* Reset the page select to its original value */ + ret_val = phy->ops.write_reg(hw, I347AT4_PAGE_SELECT, + default_page); + if (ret_val) + goto out; + + break; + default: + ret_val = -E1000_ERR_PHY; + goto out; + } + +out: + return ret_val; +} + +/** + * igb_get_cable_length_igp_2 - Determine cable length for igp2 PHY + * @hw: pointer to the HW structure + * + * The automatic gain control (agc) normalizes the amplitude of the + * received signal, adjusting for the attenuation produced by the + * cable. By reading the AGC registers, which represent the + * combination of coarse and fine gain value, the value can be put + * into a lookup table to obtain the approximate cable length + * for each channel. + **/ +s32 igb_get_cable_length_igp_2(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val = 0; + u16 phy_data, i, agc_value = 0; + u16 cur_agc_index, max_agc_index = 0; + u16 min_agc_index = IGP02E1000_CABLE_LENGTH_TABLE_SIZE - 1; + static const u16 agc_reg_array[IGP02E1000_PHY_CHANNEL_NUM] = { + IGP02E1000_PHY_AGC_A, + IGP02E1000_PHY_AGC_B, + IGP02E1000_PHY_AGC_C, + IGP02E1000_PHY_AGC_D + }; + + /* Read the AGC registers for all channels */ + for (i = 0; i < IGP02E1000_PHY_CHANNEL_NUM; i++) { + ret_val = phy->ops.read_reg(hw, agc_reg_array[i], &phy_data); + if (ret_val) + goto out; + + /* + * Getting bits 15:9, which represent the combination of + * coarse and fine gain values. The result is a number + * that can be put into the lookup table to obtain the + * approximate cable length. + */ + cur_agc_index = (phy_data >> IGP02E1000_AGC_LENGTH_SHIFT) & + IGP02E1000_AGC_LENGTH_MASK; + + /* Array index bound check. */ + if ((cur_agc_index >= IGP02E1000_CABLE_LENGTH_TABLE_SIZE) || + (cur_agc_index == 0)) { + ret_val = -E1000_ERR_PHY; + goto out; + } + + /* Remove min & max AGC values from calculation. */ + if (e1000_igp_2_cable_length_table[min_agc_index] > + e1000_igp_2_cable_length_table[cur_agc_index]) + min_agc_index = cur_agc_index; + if (e1000_igp_2_cable_length_table[max_agc_index] < + e1000_igp_2_cable_length_table[cur_agc_index]) + max_agc_index = cur_agc_index; + + agc_value += e1000_igp_2_cable_length_table[cur_agc_index]; + } + + agc_value -= (e1000_igp_2_cable_length_table[min_agc_index] + + e1000_igp_2_cable_length_table[max_agc_index]); + agc_value /= (IGP02E1000_PHY_CHANNEL_NUM - 2); + + /* Calculate cable length with the error range of +/- 10 meters. */ + phy->min_cable_length = ((agc_value - IGP02E1000_AGC_RANGE) > 0) ? + (agc_value - IGP02E1000_AGC_RANGE) : 0; + phy->max_cable_length = agc_value + IGP02E1000_AGC_RANGE; + + phy->cable_length = (phy->min_cable_length + phy->max_cable_length) / 2; + +out: + return ret_val; +} + +/** + * igb_get_phy_info_m88 - Retrieve PHY information + * @hw: pointer to the HW structure + * + * Valid for only copper links. Read the PHY status register (sticky read) + * to verify that link is up. Read the PHY special control register to + * determine the polarity and 10base-T extended distance. Read the PHY + * special status register to determine MDI/MDIx and current speed. If + * speed is 1000, then determine cable length, local and remote receiver. + **/ +s32 igb_get_phy_info_m88(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 phy_data; + bool link; + + if (phy->media_type != e1000_media_type_copper) { + hw_dbg("Phy info is only valid for copper media\n"); + ret_val = -E1000_ERR_CONFIG; + goto out; + } + + ret_val = igb_phy_has_link(hw, 1, 0, &link); + if (ret_val) + goto out; + + if (!link) { + hw_dbg("Phy info is only valid if link is up\n"); + ret_val = -E1000_ERR_CONFIG; + goto out; + } + + ret_val = phy->ops.read_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); + if (ret_val) + goto out; + + phy->polarity_correction = (phy_data & M88E1000_PSCR_POLARITY_REVERSAL) + ? true : false; + + ret_val = igb_check_polarity_m88(hw); + if (ret_val) + goto out; + + ret_val = phy->ops.read_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data); + if (ret_val) + goto out; + + phy->is_mdix = (phy_data & M88E1000_PSSR_MDIX) ? true : false; + + if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS) { + ret_val = phy->ops.get_cable_length(hw); + if (ret_val) + goto out; + + ret_val = phy->ops.read_reg(hw, PHY_1000T_STATUS, &phy_data); + if (ret_val) + goto out; + + phy->local_rx = (phy_data & SR_1000T_LOCAL_RX_STATUS) + ? e1000_1000t_rx_status_ok + : e1000_1000t_rx_status_not_ok; + + phy->remote_rx = (phy_data & SR_1000T_REMOTE_RX_STATUS) + ? e1000_1000t_rx_status_ok + : e1000_1000t_rx_status_not_ok; + } else { + /* Set values to "undefined" */ + phy->cable_length = E1000_CABLE_LENGTH_UNDEFINED; + phy->local_rx = e1000_1000t_rx_status_undefined; + phy->remote_rx = e1000_1000t_rx_status_undefined; + } + +out: + return ret_val; +} + +/** + * igb_get_phy_info_igp - Retrieve igp PHY information + * @hw: pointer to the HW structure + * + * Read PHY status to determine if link is up. If link is up, then + * set/determine 10base-T extended distance and polarity correction. Read + * PHY port status to determine MDI/MDIx and speed. Based on the speed, + * determine on the cable length, local and remote receiver. + **/ +s32 igb_get_phy_info_igp(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 data; + bool link; + + ret_val = igb_phy_has_link(hw, 1, 0, &link); + if (ret_val) + goto out; + + if (!link) { + hw_dbg("Phy info is only valid if link is up\n"); + ret_val = -E1000_ERR_CONFIG; + goto out; + } + + phy->polarity_correction = true; + + ret_val = igb_check_polarity_igp(hw); + if (ret_val) + goto out; + + ret_val = phy->ops.read_reg(hw, IGP01E1000_PHY_PORT_STATUS, &data); + if (ret_val) + goto out; + + phy->is_mdix = (data & IGP01E1000_PSSR_MDIX) ? true : false; + + if ((data & IGP01E1000_PSSR_SPEED_MASK) == + IGP01E1000_PSSR_SPEED_1000MBPS) { + ret_val = phy->ops.get_cable_length(hw); + if (ret_val) + goto out; + + ret_val = phy->ops.read_reg(hw, PHY_1000T_STATUS, &data); + if (ret_val) + goto out; + + phy->local_rx = (data & SR_1000T_LOCAL_RX_STATUS) + ? e1000_1000t_rx_status_ok + : e1000_1000t_rx_status_not_ok; + + phy->remote_rx = (data & SR_1000T_REMOTE_RX_STATUS) + ? e1000_1000t_rx_status_ok + : e1000_1000t_rx_status_not_ok; + } else { + phy->cable_length = E1000_CABLE_LENGTH_UNDEFINED; + phy->local_rx = e1000_1000t_rx_status_undefined; + phy->remote_rx = e1000_1000t_rx_status_undefined; + } + +out: + return ret_val; +} + +/** + * igb_phy_sw_reset - PHY software reset + * @hw: pointer to the HW structure + * + * Does a software reset of the PHY by reading the PHY control register and + * setting/write the control register reset bit to the PHY. + **/ +s32 igb_phy_sw_reset(struct e1000_hw *hw) +{ + s32 ret_val = 0; + u16 phy_ctrl; + + if (!(hw->phy.ops.read_reg)) + goto out; + + ret_val = hw->phy.ops.read_reg(hw, PHY_CONTROL, &phy_ctrl); + if (ret_val) + goto out; + + phy_ctrl |= MII_CR_RESET; + ret_val = hw->phy.ops.write_reg(hw, PHY_CONTROL, phy_ctrl); + if (ret_val) + goto out; + + udelay(1); + +out: + return ret_val; +} + +/** + * igb_phy_hw_reset - PHY hardware reset + * @hw: pointer to the HW structure + * + * Verify the reset block is not blocking us from resetting. Acquire + * semaphore (if necessary) and read/set/write the device control reset + * bit in the PHY. Wait the appropriate delay time for the device to + * reset and relase the semaphore (if necessary). + **/ +s32 igb_phy_hw_reset(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u32 ctrl; + + ret_val = igb_check_reset_block(hw); + if (ret_val) { + ret_val = 0; + goto out; + } + + ret_val = phy->ops.acquire(hw); + if (ret_val) + goto out; + + ctrl = rd32(E1000_CTRL); + wr32(E1000_CTRL, ctrl | E1000_CTRL_PHY_RST); + wrfl(); + + udelay(phy->reset_delay_us); + + wr32(E1000_CTRL, ctrl); + wrfl(); + + udelay(150); + + phy->ops.release(hw); + + ret_val = phy->ops.get_cfg_done(hw); + +out: + return ret_val; +} + +/** + * igb_phy_init_script_igp3 - Inits the IGP3 PHY + * @hw: pointer to the HW structure + * + * Initializes a Intel Gigabit PHY3 when an EEPROM is not present. + **/ +s32 igb_phy_init_script_igp3(struct e1000_hw *hw) +{ + hw_dbg("Running IGP 3 PHY init script\n"); + + /* PHY init IGP 3 */ + /* Enable rise/fall, 10-mode work in class-A */ + hw->phy.ops.write_reg(hw, 0x2F5B, 0x9018); + /* Remove all caps from Replica path filter */ + hw->phy.ops.write_reg(hw, 0x2F52, 0x0000); + /* Bias trimming for ADC, AFE and Driver (Default) */ + hw->phy.ops.write_reg(hw, 0x2FB1, 0x8B24); + /* Increase Hybrid poly bias */ + hw->phy.ops.write_reg(hw, 0x2FB2, 0xF8F0); + /* Add 4% to TX amplitude in Giga mode */ + hw->phy.ops.write_reg(hw, 0x2010, 0x10B0); + /* Disable trimming (TTT) */ + hw->phy.ops.write_reg(hw, 0x2011, 0x0000); + /* Poly DC correction to 94.6% + 2% for all channels */ + hw->phy.ops.write_reg(hw, 0x20DD, 0x249A); + /* ABS DC correction to 95.9% */ + hw->phy.ops.write_reg(hw, 0x20DE, 0x00D3); + /* BG temp curve trim */ + hw->phy.ops.write_reg(hw, 0x28B4, 0x04CE); + /* Increasing ADC OPAMP stage 1 currents to max */ + hw->phy.ops.write_reg(hw, 0x2F70, 0x29E4); + /* Force 1000 ( required for enabling PHY regs configuration) */ + hw->phy.ops.write_reg(hw, 0x0000, 0x0140); + /* Set upd_freq to 6 */ + hw->phy.ops.write_reg(hw, 0x1F30, 0x1606); + /* Disable NPDFE */ + hw->phy.ops.write_reg(hw, 0x1F31, 0xB814); + /* Disable adaptive fixed FFE (Default) */ + hw->phy.ops.write_reg(hw, 0x1F35, 0x002A); + /* Enable FFE hysteresis */ + hw->phy.ops.write_reg(hw, 0x1F3E, 0x0067); + /* Fixed FFE for short cable lengths */ + hw->phy.ops.write_reg(hw, 0x1F54, 0x0065); + /* Fixed FFE for medium cable lengths */ + hw->phy.ops.write_reg(hw, 0x1F55, 0x002A); + /* Fixed FFE for long cable lengths */ + hw->phy.ops.write_reg(hw, 0x1F56, 0x002A); + /* Enable Adaptive Clip Threshold */ + hw->phy.ops.write_reg(hw, 0x1F72, 0x3FB0); + /* AHT reset limit to 1 */ + hw->phy.ops.write_reg(hw, 0x1F76, 0xC0FF); + /* Set AHT master delay to 127 msec */ + hw->phy.ops.write_reg(hw, 0x1F77, 0x1DEC); + /* Set scan bits for AHT */ + hw->phy.ops.write_reg(hw, 0x1F78, 0xF9EF); + /* Set AHT Preset bits */ + hw->phy.ops.write_reg(hw, 0x1F79, 0x0210); + /* Change integ_factor of channel A to 3 */ + hw->phy.ops.write_reg(hw, 0x1895, 0x0003); + /* Change prop_factor of channels BCD to 8 */ + hw->phy.ops.write_reg(hw, 0x1796, 0x0008); + /* Change cg_icount + enable integbp for channels BCD */ + hw->phy.ops.write_reg(hw, 0x1798, 0xD008); + /* + * Change cg_icount + enable integbp + change prop_factor_master + * to 8 for channel A + */ + hw->phy.ops.write_reg(hw, 0x1898, 0xD918); + /* Disable AHT in Slave mode on channel A */ + hw->phy.ops.write_reg(hw, 0x187A, 0x0800); + /* + * Enable LPLU and disable AN to 1000 in non-D0a states, + * Enable SPD+B2B + */ + hw->phy.ops.write_reg(hw, 0x0019, 0x008D); + /* Enable restart AN on an1000_dis change */ + hw->phy.ops.write_reg(hw, 0x001B, 0x2080); + /* Enable wh_fifo read clock in 10/100 modes */ + hw->phy.ops.write_reg(hw, 0x0014, 0x0045); + /* Restart AN, Speed selection is 1000 */ + hw->phy.ops.write_reg(hw, 0x0000, 0x1340); + + return 0; +} + +/** + * igb_power_up_phy_copper - Restore copper link in case of PHY power down + * @hw: pointer to the HW structure + * + * In the case of a PHY power down to save power, or to turn off link during a + * driver unload, restore the link to previous settings. + **/ +void igb_power_up_phy_copper(struct e1000_hw *hw) +{ + u16 mii_reg = 0; + + /* The PHY will retain its settings across a power down/up cycle */ + hw->phy.ops.read_reg(hw, PHY_CONTROL, &mii_reg); + mii_reg &= ~MII_CR_POWER_DOWN; + hw->phy.ops.write_reg(hw, PHY_CONTROL, mii_reg); +} + +/** + * igb_power_down_phy_copper - Power down copper PHY + * @hw: pointer to the HW structure + * + * Power down PHY to save power when interface is down and wake on lan + * is not enabled. + **/ +void igb_power_down_phy_copper(struct e1000_hw *hw) +{ + u16 mii_reg = 0; + + /* The PHY will retain its settings across a power down/up cycle */ + hw->phy.ops.read_reg(hw, PHY_CONTROL, &mii_reg); + mii_reg |= MII_CR_POWER_DOWN; + hw->phy.ops.write_reg(hw, PHY_CONTROL, mii_reg); + msleep(1); +} + +/** + * igb_check_polarity_82580 - Checks the polarity. + * @hw: pointer to the HW structure + * + * Success returns 0, Failure returns -E1000_ERR_PHY (-2) + * + * Polarity is determined based on the PHY specific status register. + **/ +static s32 igb_check_polarity_82580(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 data; + + + ret_val = phy->ops.read_reg(hw, I82580_PHY_STATUS_2, &data); + + if (!ret_val) + phy->cable_polarity = (data & I82580_PHY_STATUS2_REV_POLARITY) + ? e1000_rev_polarity_reversed + : e1000_rev_polarity_normal; + + return ret_val; +} + +/** + * igb_phy_force_speed_duplex_82580 - Force speed/duplex for I82580 PHY + * @hw: pointer to the HW structure + * + * Calls the PHY setup function to force speed and duplex. Clears the + * auto-crossover to force MDI manually. Waits for link and returns + * successful if link up is successful, else -E1000_ERR_PHY (-2). + **/ +s32 igb_phy_force_speed_duplex_82580(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 phy_data; + bool link; + + + ret_val = phy->ops.read_reg(hw, PHY_CONTROL, &phy_data); + if (ret_val) + goto out; + + igb_phy_force_speed_duplex_setup(hw, &phy_data); + + ret_val = phy->ops.write_reg(hw, PHY_CONTROL, phy_data); + if (ret_val) + goto out; + + /* + * Clear Auto-Crossover to force MDI manually. 82580 requires MDI + * forced whenever speed and duplex are forced. + */ + ret_val = phy->ops.read_reg(hw, I82580_PHY_CTRL_2, &phy_data); + if (ret_val) + goto out; + + phy_data &= ~I82580_PHY_CTRL2_AUTO_MDIX; + phy_data &= ~I82580_PHY_CTRL2_FORCE_MDI_MDIX; + + ret_val = phy->ops.write_reg(hw, I82580_PHY_CTRL_2, phy_data); + if (ret_val) + goto out; + + hw_dbg("I82580_PHY_CTRL_2: %X\n", phy_data); + + udelay(1); + + if (phy->autoneg_wait_to_complete) { + hw_dbg("Waiting for forced speed/duplex link on 82580 phy\n"); + + ret_val = igb_phy_has_link(hw, + PHY_FORCE_LIMIT, + 100000, + &link); + if (ret_val) + goto out; + + if (!link) + hw_dbg("Link taking longer than expected.\n"); + + /* Try once more */ + ret_val = igb_phy_has_link(hw, + PHY_FORCE_LIMIT, + 100000, + &link); + if (ret_val) + goto out; + } + +out: + return ret_val; +} + +/** + * igb_get_phy_info_82580 - Retrieve I82580 PHY information + * @hw: pointer to the HW structure + * + * Read PHY status to determine if link is up. If link is up, then + * set/determine 10base-T extended distance and polarity correction. Read + * PHY port status to determine MDI/MDIx and speed. Based on the speed, + * determine on the cable length, local and remote receiver. + **/ +s32 igb_get_phy_info_82580(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 data; + bool link; + + + ret_val = igb_phy_has_link(hw, 1, 0, &link); + if (ret_val) + goto out; + + if (!link) { + hw_dbg("Phy info is only valid if link is up\n"); + ret_val = -E1000_ERR_CONFIG; + goto out; + } + + phy->polarity_correction = true; + + ret_val = igb_check_polarity_82580(hw); + if (ret_val) + goto out; + + ret_val = phy->ops.read_reg(hw, I82580_PHY_STATUS_2, &data); + if (ret_val) + goto out; + + phy->is_mdix = (data & I82580_PHY_STATUS2_MDIX) ? true : false; + + if ((data & I82580_PHY_STATUS2_SPEED_MASK) == + I82580_PHY_STATUS2_SPEED_1000MBPS) { + ret_val = hw->phy.ops.get_cable_length(hw); + if (ret_val) + goto out; + + ret_val = phy->ops.read_reg(hw, PHY_1000T_STATUS, &data); + if (ret_val) + goto out; + + phy->local_rx = (data & SR_1000T_LOCAL_RX_STATUS) + ? e1000_1000t_rx_status_ok + : e1000_1000t_rx_status_not_ok; + + phy->remote_rx = (data & SR_1000T_REMOTE_RX_STATUS) + ? e1000_1000t_rx_status_ok + : e1000_1000t_rx_status_not_ok; + } else { + phy->cable_length = E1000_CABLE_LENGTH_UNDEFINED; + phy->local_rx = e1000_1000t_rx_status_undefined; + phy->remote_rx = e1000_1000t_rx_status_undefined; + } + +out: + return ret_val; +} + +/** + * igb_get_cable_length_82580 - Determine cable length for 82580 PHY + * @hw: pointer to the HW structure + * + * Reads the diagnostic status register and verifies result is valid before + * placing it in the phy_cable_length field. + **/ +s32 igb_get_cable_length_82580(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 phy_data, length; + + + ret_val = phy->ops.read_reg(hw, I82580_PHY_DIAG_STATUS, &phy_data); + if (ret_val) + goto out; + + length = (phy_data & I82580_DSTATUS_CABLE_LENGTH) >> + I82580_DSTATUS_CABLE_LENGTH_SHIFT; + + if (length == E1000_CABLE_LENGTH_UNDEFINED) + ret_val = -E1000_ERR_PHY; + + phy->cable_length = length; + +out: + return ret_val; +} |