diff options
Diffstat (limited to 'drivers/net/ethernet/intel/e1000e/param.c')
| -rw-r--r-- | drivers/net/ethernet/intel/e1000e/param.c | 99 |
1 files changed, 53 insertions, 46 deletions
diff --git a/drivers/net/ethernet/intel/e1000e/param.c b/drivers/net/ethernet/intel/e1000e/param.c index ff796e42c3e..16adeb9418a 100644 --- a/drivers/net/ethernet/intel/e1000e/param.c +++ b/drivers/net/ethernet/intel/e1000e/param.c @@ -106,7 +106,7 @@ E1000_PARAM(RxAbsIntDelay, "Receive Absolute Interrupt Delay"); /* * Interrupt Throttle Rate (interrupts/sec) * - * Valid Range: 100-100000 (0=off, 1=dynamic, 3=dynamic conservative) + * Valid Range: 100-100000 or one of: 0=off, 1=dynamic, 3=dynamic conservative */ E1000_PARAM(InterruptThrottleRate, "Interrupt Throttling Rate"); #define DEFAULT_ITR 3 @@ -344,53 +344,60 @@ void __devinit e1000e_check_options(struct e1000_adapter *adapter) if (num_InterruptThrottleRate > bd) { adapter->itr = InterruptThrottleRate[bd]; - switch (adapter->itr) { - case 0: - e_info("%s turned off\n", opt.name); - break; - case 1: - e_info("%s set to dynamic mode\n", opt.name); - adapter->itr_setting = adapter->itr; - adapter->itr = 20000; - break; - case 3: - e_info("%s set to dynamic conservative mode\n", - opt.name); - adapter->itr_setting = adapter->itr; - adapter->itr = 20000; - break; - case 4: - e_info("%s set to simplified (2000-8000 ints) " - "mode\n", opt.name); - adapter->itr_setting = 4; - break; - default: - /* - * Save the setting, because the dynamic bits - * change itr. - */ - if (e1000_validate_option(&adapter->itr, &opt, - adapter) && - (adapter->itr == 3)) { - /* - * In case of invalid user value, - * default to conservative mode. - */ - adapter->itr_setting = adapter->itr; - adapter->itr = 20000; - } else { - /* - * Clear the lower two bits because - * they are used as control. - */ - adapter->itr_setting = - adapter->itr & ~3; - } - break; - } + + /* + * Make sure a message is printed for non-special + * values. And in case of an invalid option, display + * warning, use default and got through itr/itr_setting + * adjustment logic below + */ + if ((adapter->itr > 4) && + e1000_validate_option(&adapter->itr, &opt, adapter)) + adapter->itr = opt.def; } else { - adapter->itr_setting = opt.def; + /* + * If no option specified, use default value and go + * through the logic below to adjust itr/itr_setting + */ + adapter->itr = opt.def; + + /* + * Make sure a message is printed for non-special + * default values + */ + if (adapter->itr > 40) + e_info("%s set to default %d\n", opt.name, + adapter->itr); + } + + adapter->itr_setting = adapter->itr; + switch (adapter->itr) { + case 0: + e_info("%s turned off\n", opt.name); + break; + case 1: + e_info("%s set to dynamic mode\n", opt.name); + adapter->itr = 20000; + break; + case 3: + e_info("%s set to dynamic conservative mode\n", + opt.name); adapter->itr = 20000; + break; + case 4: + e_info("%s set to simplified (2000-8000 ints) mode\n", + opt.name); + break; + default: + /* + * Save the setting, because the dynamic bits + * change itr. + * + * Clear the lower two bits because + * they are used as control. + */ + adapter->itr_setting &= ~3; + break; } } { /* Interrupt Mode */ |