aboutsummaryrefslogtreecommitdiff
path: root/drivers/net/bnx2x/bnx2x_link.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/bnx2x/bnx2x_link.c')
-rw-r--r--drivers/net/bnx2x/bnx2x_link.c6735
1 files changed, 6735 insertions, 0 deletions
diff --git a/drivers/net/bnx2x/bnx2x_link.c b/drivers/net/bnx2x/bnx2x_link.c
new file mode 100644
index 00000000000..0383e306631
--- /dev/null
+++ b/drivers/net/bnx2x/bnx2x_link.c
@@ -0,0 +1,6735 @@
+/* Copyright 2008-2009 Broadcom Corporation
+ *
+ * Unless you and Broadcom execute a separate written software license
+ * agreement governing use of this software, this software is licensed to you
+ * under the terms of the GNU General Public License version 2, available
+ * at http://www.gnu.org/licenses/old-licenses/gpl-2.0.html (the "GPL").
+ *
+ * Notwithstanding the above, under no circumstances may you combine this
+ * software in any way with any other Broadcom software provided under a
+ * license other than the GPL, without Broadcom's express prior written
+ * consent.
+ *
+ * Written by Yaniv Rosner
+ *
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/pci.h>
+#include <linux/netdevice.h>
+#include <linux/delay.h>
+#include <linux/ethtool.h>
+#include <linux/mutex.h>
+
+#include "bnx2x.h"
+
+/********************************************************/
+#define ETH_HLEN 14
+#define ETH_OVREHEAD (ETH_HLEN + 8)/* 8 for CRC + VLAN*/
+#define ETH_MIN_PACKET_SIZE 60
+#define ETH_MAX_PACKET_SIZE 1500
+#define ETH_MAX_JUMBO_PACKET_SIZE 9600
+#define MDIO_ACCESS_TIMEOUT 1000
+#define BMAC_CONTROL_RX_ENABLE 2
+
+/***********************************************************/
+/* Shortcut definitions */
+/***********************************************************/
+
+#define NIG_LATCH_BC_ENABLE_MI_INT 0
+
+#define NIG_STATUS_EMAC0_MI_INT \
+ NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_EMAC0_MISC_MI_INT
+#define NIG_STATUS_XGXS0_LINK10G \
+ NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_XGXS0_LINK10G
+#define NIG_STATUS_XGXS0_LINK_STATUS \
+ NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_XGXS0_LINK_STATUS
+#define NIG_STATUS_XGXS0_LINK_STATUS_SIZE \
+ NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_XGXS0_LINK_STATUS_SIZE
+#define NIG_STATUS_SERDES0_LINK_STATUS \
+ NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_SERDES0_LINK_STATUS
+#define NIG_MASK_MI_INT \
+ NIG_MASK_INTERRUPT_PORT0_REG_MASK_EMAC0_MISC_MI_INT
+#define NIG_MASK_XGXS0_LINK10G \
+ NIG_MASK_INTERRUPT_PORT0_REG_MASK_XGXS0_LINK10G
+#define NIG_MASK_XGXS0_LINK_STATUS \
+ NIG_MASK_INTERRUPT_PORT0_REG_MASK_XGXS0_LINK_STATUS
+#define NIG_MASK_SERDES0_LINK_STATUS \
+ NIG_MASK_INTERRUPT_PORT0_REG_MASK_SERDES0_LINK_STATUS
+
+#define MDIO_AN_CL73_OR_37_COMPLETE \
+ (MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_AUTONEG_COMPLETE | \
+ MDIO_GP_STATUS_TOP_AN_STATUS1_CL37_AUTONEG_COMPLETE)
+
+#define XGXS_RESET_BITS \
+ (MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_RSTB_HW | \
+ MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_IDDQ | \
+ MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_PWRDWN | \
+ MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_PWRDWN_SD | \
+ MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_TXD_FIFO_RSTB)
+
+#define SERDES_RESET_BITS \
+ (MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_SERDES0_RSTB_HW | \
+ MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_SERDES0_IDDQ | \
+ MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_SERDES0_PWRDWN | \
+ MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_SERDES0_PWRDWN_SD)
+
+#define AUTONEG_CL37 SHARED_HW_CFG_AN_ENABLE_CL37
+#define AUTONEG_CL73 SHARED_HW_CFG_AN_ENABLE_CL73
+#define AUTONEG_BAM SHARED_HW_CFG_AN_ENABLE_BAM
+#define AUTONEG_PARALLEL \
+ SHARED_HW_CFG_AN_ENABLE_PARALLEL_DETECTION
+#define AUTONEG_SGMII_FIBER_AUTODET \
+ SHARED_HW_CFG_AN_EN_SGMII_FIBER_AUTO_DETECT
+#define AUTONEG_REMOTE_PHY SHARED_HW_CFG_AN_ENABLE_REMOTE_PHY
+
+#define GP_STATUS_PAUSE_RSOLUTION_TXSIDE \
+ MDIO_GP_STATUS_TOP_AN_STATUS1_PAUSE_RSOLUTION_TXSIDE
+#define GP_STATUS_PAUSE_RSOLUTION_RXSIDE \
+ MDIO_GP_STATUS_TOP_AN_STATUS1_PAUSE_RSOLUTION_RXSIDE
+#define GP_STATUS_SPEED_MASK \
+ MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_MASK
+#define GP_STATUS_10M MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10M
+#define GP_STATUS_100M MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_100M
+#define GP_STATUS_1G MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_1G
+#define GP_STATUS_2_5G MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_2_5G
+#define GP_STATUS_5G MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_5G
+#define GP_STATUS_6G MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_6G
+#define GP_STATUS_10G_HIG \
+ MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_HIG
+#define GP_STATUS_10G_CX4 \
+ MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_CX4
+#define GP_STATUS_12G_HIG \
+ MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_12G_HIG
+#define GP_STATUS_12_5G MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_12_5G
+#define GP_STATUS_13G MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_13G
+#define GP_STATUS_15G MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_15G
+#define GP_STATUS_16G MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_16G
+#define GP_STATUS_1G_KX MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_1G_KX
+#define GP_STATUS_10G_KX4 \
+ MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_KX4
+
+#define LINK_10THD LINK_STATUS_SPEED_AND_DUPLEX_10THD
+#define LINK_10TFD LINK_STATUS_SPEED_AND_DUPLEX_10TFD
+#define LINK_100TXHD LINK_STATUS_SPEED_AND_DUPLEX_100TXHD
+#define LINK_100T4 LINK_STATUS_SPEED_AND_DUPLEX_100T4
+#define LINK_100TXFD LINK_STATUS_SPEED_AND_DUPLEX_100TXFD
+#define LINK_1000THD LINK_STATUS_SPEED_AND_DUPLEX_1000THD
+#define LINK_1000TFD LINK_STATUS_SPEED_AND_DUPLEX_1000TFD
+#define LINK_1000XFD LINK_STATUS_SPEED_AND_DUPLEX_1000XFD
+#define LINK_2500THD LINK_STATUS_SPEED_AND_DUPLEX_2500THD
+#define LINK_2500TFD LINK_STATUS_SPEED_AND_DUPLEX_2500TFD
+#define LINK_2500XFD LINK_STATUS_SPEED_AND_DUPLEX_2500XFD
+#define LINK_10GTFD LINK_STATUS_SPEED_AND_DUPLEX_10GTFD
+#define LINK_10GXFD LINK_STATUS_SPEED_AND_DUPLEX_10GXFD
+#define LINK_12GTFD LINK_STATUS_SPEED_AND_DUPLEX_12GTFD
+#define LINK_12GXFD LINK_STATUS_SPEED_AND_DUPLEX_12GXFD
+#define LINK_12_5GTFD LINK_STATUS_SPEED_AND_DUPLEX_12_5GTFD
+#define LINK_12_5GXFD LINK_STATUS_SPEED_AND_DUPLEX_12_5GXFD
+#define LINK_13GTFD LINK_STATUS_SPEED_AND_DUPLEX_13GTFD
+#define LINK_13GXFD LINK_STATUS_SPEED_AND_DUPLEX_13GXFD
+#define LINK_15GTFD LINK_STATUS_SPEED_AND_DUPLEX_15GTFD
+#define LINK_15GXFD LINK_STATUS_SPEED_AND_DUPLEX_15GXFD
+#define LINK_16GTFD LINK_STATUS_SPEED_AND_DUPLEX_16GTFD
+#define LINK_16GXFD LINK_STATUS_SPEED_AND_DUPLEX_16GXFD
+
+#define PHY_XGXS_FLAG 0x1
+#define PHY_SGMII_FLAG 0x2
+#define PHY_SERDES_FLAG 0x4
+
+/* */
+#define SFP_EEPROM_CON_TYPE_ADDR 0x2
+ #define SFP_EEPROM_CON_TYPE_VAL_LC 0x7
+ #define SFP_EEPROM_CON_TYPE_VAL_COPPER 0x21
+
+
+#define SFP_EEPROM_COMP_CODE_ADDR 0x3
+ #define SFP_EEPROM_COMP_CODE_SR_MASK (1<<4)
+ #define SFP_EEPROM_COMP_CODE_LR_MASK (1<<5)
+ #define SFP_EEPROM_COMP_CODE_LRM_MASK (1<<6)
+
+#define SFP_EEPROM_FC_TX_TECH_ADDR 0x8
+ #define SFP_EEPROM_FC_TX_TECH_BITMASK_COPPER_PASSIVE 0x4
+ #define SFP_EEPROM_FC_TX_TECH_BITMASK_COPPER_ACTIVE 0x8
+
+#define SFP_EEPROM_OPTIONS_ADDR 0x40
+ #define SFP_EEPROM_OPTIONS_LINEAR_RX_OUT_MASK 0x1
+#define SFP_EEPROM_OPTIONS_SIZE 2
+
+#define EDC_MODE_LINEAR 0x0022
+#define EDC_MODE_LIMITING 0x0044
+#define EDC_MODE_PASSIVE_DAC 0x0055
+
+
+
+/**********************************************************/
+/* INTERFACE */
+/**********************************************************/
+#define CL45_WR_OVER_CL22(_bp, _port, _phy_addr, _bank, _addr, _val) \
+ bnx2x_cl45_write(_bp, _port, 0, _phy_addr, \
+ DEFAULT_PHY_DEV_ADDR, \
+ (_bank + (_addr & 0xf)), \
+ _val)
+
+#define CL45_RD_OVER_CL22(_bp, _port, _phy_addr, _bank, _addr, _val) \
+ bnx2x_cl45_read(_bp, _port, 0, _phy_addr, \
+ DEFAULT_PHY_DEV_ADDR, \
+ (_bank + (_addr & 0xf)), \
+ _val)
+
+static void bnx2x_set_serdes_access(struct link_params *params)
+{
+ struct bnx2x *bp = params->bp;
+ u32 emac_base = (params->port) ? GRCBASE_EMAC1 : GRCBASE_EMAC0;
+
+ /* Set Clause 22 */
+ REG_WR(bp, NIG_REG_SERDES0_CTRL_MD_ST + params->port*0x10, 1);
+ REG_WR(bp, emac_base + EMAC_REG_EMAC_MDIO_COMM, 0x245f8000);
+ udelay(500);
+ REG_WR(bp, emac_base + EMAC_REG_EMAC_MDIO_COMM, 0x245d000f);
+ udelay(500);
+ /* Set Clause 45 */
+ REG_WR(bp, NIG_REG_SERDES0_CTRL_MD_ST + params->port*0x10, 0);
+}
+static void bnx2x_set_phy_mdio(struct link_params *params, u8 phy_flags)
+{
+ struct bnx2x *bp = params->bp;
+
+ if (phy_flags & PHY_XGXS_FLAG) {
+ REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_ST +
+ params->port*0x18, 0);
+ REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_DEVAD + params->port*0x18,
+ DEFAULT_PHY_DEV_ADDR);
+ } else {
+ bnx2x_set_serdes_access(params);
+
+ REG_WR(bp, NIG_REG_SERDES0_CTRL_MD_DEVAD +
+ params->port*0x10,
+ DEFAULT_PHY_DEV_ADDR);
+ }
+}
+
+static u32 bnx2x_bits_en(struct bnx2x *bp, u32 reg, u32 bits)
+{
+ u32 val = REG_RD(bp, reg);
+
+ val |= bits;
+ REG_WR(bp, reg, val);
+ return val;
+}
+
+static u32 bnx2x_bits_dis(struct bnx2x *bp, u32 reg, u32 bits)
+{
+ u32 val = REG_RD(bp, reg);
+
+ val &= ~bits;
+ REG_WR(bp, reg, val);
+ return val;
+}
+
+static void bnx2x_emac_init(struct link_params *params,
+ struct link_vars *vars)
+{
+ /* reset and unreset the emac core */
+ struct bnx2x *bp = params->bp;
+ u8 port = params->port;
+ u32 emac_base = port ? GRCBASE_EMAC1 : GRCBASE_EMAC0;
+ u32 val;
+ u16 timeout;
+
+ REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR,
+ (MISC_REGISTERS_RESET_REG_2_RST_EMAC0_HARD_CORE << port));
+ udelay(5);
+ REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET,
+ (MISC_REGISTERS_RESET_REG_2_RST_EMAC0_HARD_CORE << port));
+
+ /* init emac - use read-modify-write */
+ /* self clear reset */
+ val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MODE);
+ EMAC_WR(bp, EMAC_REG_EMAC_MODE, (val | EMAC_MODE_RESET));
+
+ timeout = 200;
+ do {
+ val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MODE);
+ DP(NETIF_MSG_LINK, "EMAC reset reg is %u\n", val);
+ if (!timeout) {
+ DP(NETIF_MSG_LINK, "EMAC timeout!\n");
+ return;
+ }
+ timeout--;
+ } while (val & EMAC_MODE_RESET);
+
+ /* Set mac address */
+ val = ((params->mac_addr[0] << 8) |
+ params->mac_addr[1]);
+ EMAC_WR(bp, EMAC_REG_EMAC_MAC_MATCH, val);
+
+ val = ((params->mac_addr[2] << 24) |
+ (params->mac_addr[3] << 16) |
+ (params->mac_addr[4] << 8) |
+ params->mac_addr[5]);
+ EMAC_WR(bp, EMAC_REG_EMAC_MAC_MATCH + 4, val);
+}
+
+static u8 bnx2x_emac_enable(struct link_params *params,
+ struct link_vars *vars, u8 lb)
+{
+ struct bnx2x *bp = params->bp;
+ u8 port = params->port;
+ u32 emac_base = port ? GRCBASE_EMAC1 : GRCBASE_EMAC0;
+ u32 val;
+
+ DP(NETIF_MSG_LINK, "enabling EMAC\n");
+
+ /* enable emac and not bmac */
+ REG_WR(bp, NIG_REG_EGRESS_EMAC0_PORT + port*4, 1);
+
+ /* for paladium */
+ if (CHIP_REV_IS_EMUL(bp)) {
+ /* Use lane 1 (of lanes 0-3) */
+ REG_WR(bp, NIG_REG_XGXS_LANE_SEL_P0 + port*4, 1);
+ REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL +
+ port*4, 1);
+ }
+ /* for fpga */
+ else
+
+ if (CHIP_REV_IS_FPGA(bp)) {
+ /* Use lane 1 (of lanes 0-3) */
+ DP(NETIF_MSG_LINK, "bnx2x_emac_enable: Setting FPGA\n");
+
+ REG_WR(bp, NIG_REG_XGXS_LANE_SEL_P0 + port*4, 1);
+ REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL + port*4,
+ 0);
+ } else
+ /* ASIC */
+ if (vars->phy_flags & PHY_XGXS_FLAG) {
+ u32 ser_lane = ((params->lane_config &
+ PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >>
+ PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT);
+
+ DP(NETIF_MSG_LINK, "XGXS\n");
+ /* select the master lanes (out of 0-3) */
+ REG_WR(bp, NIG_REG_XGXS_LANE_SEL_P0 +
+ port*4, ser_lane);
+ /* select XGXS */
+ REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL +
+ port*4, 1);
+
+ } else { /* SerDes */
+ DP(NETIF_MSG_LINK, "SerDes\n");
+ /* select SerDes */
+ REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL +
+ port*4, 0);
+ }
+
+ bnx2x_bits_en(bp, emac_base + EMAC_REG_EMAC_RX_MODE,
+ EMAC_RX_MODE_RESET);
+ bnx2x_bits_en(bp, emac_base + EMAC_REG_EMAC_TX_MODE,
+ EMAC_TX_MODE_RESET);
+
+ if (CHIP_REV_IS_SLOW(bp)) {
+ /* config GMII mode */
+ val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MODE);
+ EMAC_WR(bp, EMAC_REG_EMAC_MODE,
+ (val | EMAC_MODE_PORT_GMII));
+ } else { /* ASIC */
+ /* pause enable/disable */
+ bnx2x_bits_dis(bp, emac_base + EMAC_REG_EMAC_RX_MODE,
+ EMAC_RX_MODE_FLOW_EN);
+ if (vars->flow_ctrl & BNX2X_FLOW_CTRL_RX)
+ bnx2x_bits_en(bp, emac_base +
+ EMAC_REG_EMAC_RX_MODE,
+ EMAC_RX_MODE_FLOW_EN);
+
+ bnx2x_bits_dis(bp, emac_base + EMAC_REG_EMAC_TX_MODE,
+ (EMAC_TX_MODE_EXT_PAUSE_EN |
+ EMAC_TX_MODE_FLOW_EN));
+ if (vars->flow_ctrl & BNX2X_FLOW_CTRL_TX)
+ bnx2x_bits_en(bp, emac_base +
+ EMAC_REG_EMAC_TX_MODE,
+ (EMAC_TX_MODE_EXT_PAUSE_EN |
+ EMAC_TX_MODE_FLOW_EN));
+ }
+
+ /* KEEP_VLAN_TAG, promiscuous */
+ val = REG_RD(bp, emac_base + EMAC_REG_EMAC_RX_MODE);
+ val |= EMAC_RX_MODE_KEEP_VLAN_TAG | EMAC_RX_MODE_PROMISCUOUS;
+ EMAC_WR(bp, EMAC_REG_EMAC_RX_MODE, val);
+
+ /* Set Loopback */
+ val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MODE);
+ if (lb)
+ val |= 0x810;
+ else
+ val &= ~0x810;
+ EMAC_WR(bp, EMAC_REG_EMAC_MODE, val);
+
+ /* enable emac */
+ REG_WR(bp, NIG_REG_NIG_EMAC0_EN + port*4, 1);
+
+ /* enable emac for jumbo packets */
+ EMAC_WR(bp, EMAC_REG_EMAC_RX_MTU_SIZE,
+ (EMAC_RX_MTU_SIZE_JUMBO_ENA |
+ (ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD)));
+
+ /* strip CRC */
+ REG_WR(bp, NIG_REG_NIG_INGRESS_EMAC0_NO_CRC + port*4, 0x1);
+
+ /* disable the NIG in/out to the bmac */
+ REG_WR(bp, NIG_REG_BMAC0_IN_EN + port*4, 0x0);
+ REG_WR(bp, NIG_REG_BMAC0_PAUSE_OUT_EN + port*4, 0x0);
+ REG_WR(bp, NIG_REG_BMAC0_OUT_EN + port*4, 0x0);
+
+ /* enable the NIG in/out to the emac */
+ REG_WR(bp, NIG_REG_EMAC0_IN_EN + port*4, 0x1);
+ val = 0;
+ if (vars->flow_ctrl & BNX2X_FLOW_CTRL_TX)
+ val = 1;
+
+ REG_WR(bp, NIG_REG_EMAC0_PAUSE_OUT_EN + port*4, val);
+ REG_WR(bp, NIG_REG_EGRESS_EMAC0_OUT_EN + port*4, 0x1);
+
+ if (CHIP_REV_IS_EMUL(bp)) {
+ /* take the BigMac out of reset */
+ REG_WR(bp,
+ GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET,
+ (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));
+
+ /* enable access for bmac registers */
+ REG_WR(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4, 0x1);
+ } else
+ REG_WR(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4, 0x0);
+
+ vars->mac_type = MAC_TYPE_EMAC;
+ return 0;
+}
+
+
+
+static u8 bnx2x_bmac_enable(struct link_params *params, struct link_vars *vars,
+ u8 is_lb)
+{
+ struct bnx2x *bp = params->bp;
+ u8 port = params->port;
+ u32 bmac_addr = port ? NIG_REG_INGRESS_BMAC1_MEM :
+ NIG_REG_INGRESS_BMAC0_MEM;
+ u32 wb_data[2];
+ u32 val;
+
+ DP(NETIF_MSG_LINK, "Enabling BigMAC\n");
+ /* reset and unreset the BigMac */
+ REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR,
+ (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));
+ msleep(1);
+
+ REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET,
+ (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));
+
+ /* enable access for bmac registers */
+ REG_WR(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4, 0x1);
+
+ /* XGXS control */
+ wb_data[0] = 0x3c;
+ wb_data[1] = 0;
+ REG_WR_DMAE(bp, bmac_addr +
+ BIGMAC_REGISTER_BMAC_XGXS_CONTROL,
+ wb_data, 2);
+
+ /* tx MAC SA */
+ wb_data[0] = ((params->mac_addr[2] << 24) |
+ (params->mac_addr[3] << 16) |
+ (params->mac_addr[4] << 8) |
+ params->mac_addr[5]);
+ wb_data[1] = ((params->mac_addr[0] << 8) |
+ params->mac_addr[1]);
+ REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_TX_SOURCE_ADDR,
+ wb_data, 2);
+
+ /* tx control */
+ val = 0xc0;
+ if (vars->flow_ctrl & BNX2X_FLOW_CTRL_TX)
+ val |= 0x800000;
+ wb_data[0] = val;
+ wb_data[1] = 0;
+ REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_TX_CONTROL,
+ wb_data, 2);
+
+ /* mac control */
+ val = 0x3;
+ if (is_lb) {
+ val |= 0x4;
+ DP(NETIF_MSG_LINK, "enable bmac loopback\n");
+ }
+ wb_data[0] = val;
+ wb_data[1] = 0;
+ REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_BMAC_CONTROL,
+ wb_data, 2);
+
+ /* set rx mtu */
+ wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD;
+ wb_data[1] = 0;
+ REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_RX_MAX_SIZE,
+ wb_data, 2);
+
+ /* rx control set to don't strip crc */
+ val = 0x14;
+ if (vars->flow_ctrl & BNX2X_FLOW_CTRL_RX)
+ val |= 0x20;
+ wb_data[0] = val;
+ wb_data[1] = 0;
+ REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_RX_CONTROL,
+ wb_data, 2);
+
+ /* set tx mtu */
+ wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD;
+ wb_data[1] = 0;
+ REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_TX_MAX_SIZE,
+ wb_data, 2);
+
+ /* set cnt max size */
+ wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD;
+ wb_data[1] = 0;
+ REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_CNT_MAX_SIZE,
+ wb_data, 2);
+
+ /* configure safc */
+ wb_data[0] = 0x1000200;
+ wb_data[1] = 0;
+ REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_RX_LLFC_MSG_FLDS,
+ wb_data, 2);
+ /* fix for emulation */
+ if (CHIP_REV_IS_EMUL(bp)) {
+ wb_data[0] = 0xf000;
+ wb_data[1] = 0;
+ REG_WR_DMAE(bp,
+ bmac_addr + BIGMAC_REGISTER_TX_PAUSE_THRESHOLD,
+ wb_data, 2);
+ }
+
+ REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL + port*4, 0x1);
+ REG_WR(bp, NIG_REG_XGXS_LANE_SEL_P0 + port*4, 0x0);
+ REG_WR(bp, NIG_REG_EGRESS_EMAC0_PORT + port*4, 0x0);
+ val = 0;
+ if (vars->flow_ctrl & BNX2X_FLOW_CTRL_TX)
+ val = 1;
+ REG_WR(bp, NIG_REG_BMAC0_PAUSE_OUT_EN + port*4, val);
+ REG_WR(bp, NIG_REG_EGRESS_EMAC0_OUT_EN + port*4, 0x0);
+ REG_WR(bp, NIG_REG_EMAC0_IN_EN + port*4, 0x0);
+ REG_WR(bp, NIG_REG_EMAC0_PAUSE_OUT_EN + port*4, 0x0);
+ REG_WR(bp, NIG_REG_BMAC0_IN_EN + port*4, 0x1);
+ REG_WR(bp, NIG_REG_BMAC0_OUT_EN + port*4, 0x1);
+
+ vars->mac_type = MAC_TYPE_BMAC;
+ return 0;
+}
+
+static void bnx2x_phy_deassert(struct link_params *params, u8 phy_flags)
+{
+ struct bnx2x *bp = params->bp;
+ u32 val;
+
+ if (phy_flags & PHY_XGXS_FLAG) {
+ DP(NETIF_MSG_LINK, "bnx2x_phy_deassert:XGXS\n");
+ val = XGXS_RESET_BITS;
+
+ } else { /* SerDes */
+ DP(NETIF_MSG_LINK, "bnx2x_phy_deassert:SerDes\n");
+ val = SERDES_RESET_BITS;
+ }
+
+ val = val << (params->port*16);
+
+ /* reset and unreset the SerDes/XGXS */
+ REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_3_CLEAR,
+ val);
+ udelay(500);
+ REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_3_SET,
+ val);
+ bnx2x_set_phy_mdio(params, phy_flags);
+}
+
+void bnx2x_link_status_update(struct link_params *params,
+ struct link_vars *vars)
+{
+ struct bnx2x *bp = params->bp;
+ u8 link_10g;
+ u8 port = params->port;
+
+ if (params->switch_cfg == SWITCH_CFG_1G)
+ vars->phy_flags = PHY_SERDES_FLAG;
+ else
+ vars->phy_flags = PHY_XGXS_FLAG;
+ vars->link_status = REG_RD(bp, params->shmem_base +
+ offsetof(struct shmem_region,
+ port_mb[port].link_status));
+
+ vars->link_up = (vars->link_status & LINK_STATUS_LINK_UP);
+
+ if (vars->link_up) {
+ DP(NETIF_MSG_LINK, "phy link up\n");
+
+ vars->phy_link_up = 1;
+ vars->duplex = DUPLEX_FULL;
+ switch (vars->link_status &
+ LINK_STATUS_SPEED_AND_DUPLEX_MASK) {
+ case LINK_10THD:
+ vars->duplex = DUPLEX_HALF;
+ /* fall thru */
+ case LINK_10TFD:
+ vars->line_speed = SPEED_10;
+ break;
+
+ case LINK_100TXHD:
+ vars->duplex = DUPLEX_HALF;
+ /* fall thru */
+ case LINK_100T4:
+ case LINK_100TXFD:
+ vars->line_speed = SPEED_100;
+ break;
+
+ case LINK_1000THD:
+ vars->duplex = DUPLEX_HALF;
+ /* fall thru */
+ case LINK_1000TFD:
+ vars->line_speed = SPEED_1000;
+ break;
+
+ case LINK_2500THD:
+ vars->duplex = DUPLEX_HALF;
+ /* fall thru */
+ case LINK_2500TFD:
+ vars->line_speed = SPEED_2500;
+ break;
+
+ case LINK_10GTFD:
+ vars->line_speed = SPEED_10000;
+ break;
+
+ case LINK_12GTFD:
+ vars->line_speed = SPEED_12000;
+ break;
+
+ case LINK_12_5GTFD:
+ vars->line_speed = SPEED_12500;
+ break;
+
+ case LINK_13GTFD:
+ vars->line_speed = SPEED_13000;
+ break;
+
+ case LINK_15GTFD:
+ vars->line_speed = SPEED_15000;
+ break;
+
+ case LINK_16GTFD:
+ vars->line_speed = SPEED_16000;
+ break;
+
+ default:
+ break;
+ }
+
+ if (vars->link_status & LINK_STATUS_TX_FLOW_CONTROL_ENABLED)
+ vars->flow_ctrl |= BNX2X_FLOW_CTRL_TX;
+ else
+ vars->flow_ctrl &= ~BNX2X_FLOW_CTRL_TX;
+
+ if (vars->link_status & LINK_STATUS_RX_FLOW_CONTROL_ENABLED)
+ vars->flow_ctrl |= BNX2X_FLOW_CTRL_RX;
+ else
+ vars->flow_ctrl &= ~BNX2X_FLOW_CTRL_RX;
+
+ if (vars->phy_flags & PHY_XGXS_FLAG) {
+ if (vars->line_speed &&
+ ((vars->line_speed == SPEED_10) ||
+ (vars->line_speed == SPEED_100))) {
+ vars->phy_flags |= PHY_SGMII_FLAG;
+ } else {
+ vars->phy_flags &= ~PHY_SGMII_FLAG;
+ }
+ }
+
+ /* anything 10 and over uses the bmac */
+ link_10g = ((vars->line_speed == SPEED_10000) ||
+ (vars->line_speed == SPEED_12000) ||
+ (vars->line_speed == SPEED_12500) ||
+ (vars->line_speed == SPEED_13000) ||
+ (vars->line_speed == SPEED_15000) ||
+ (vars->line_speed == SPEED_16000));
+ if (link_10g)
+ vars->mac_type = MAC_TYPE_BMAC;
+ else
+ vars->mac_type = MAC_TYPE_EMAC;
+
+ } else { /* link down */
+ DP(NETIF_MSG_LINK, "phy link down\n");
+
+ vars->phy_link_up = 0;
+
+ vars->line_speed = 0;
+ vars->duplex = DUPLEX_FULL;
+ vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE;
+
+ /* indicate no mac active */
+ vars->mac_type = MAC_TYPE_NONE;
+ }
+
+ DP(NETIF_MSG_LINK, "link_status 0x%x phy_link_up %x\n",
+ vars->link_status, vars->phy_link_up);
+ DP(NETIF_MSG_LINK, "line_speed %x duplex %x flow_ctrl 0x%x\n",
+ vars->line_speed, vars->duplex, vars->flow_ctrl);
+}
+
+static void bnx2x_update_mng(struct link_params *params, u32 link_status)
+{
+ struct bnx2x *bp = params->bp;
+
+ REG_WR(bp, params->shmem_base +
+ offsetof(struct shmem_region,
+ port_mb[params->port].link_status),
+ link_status);
+}
+
+static void bnx2x_bmac_rx_disable(struct bnx2x *bp, u8 port)
+{
+ u32 bmac_addr = port ? NIG_REG_INGRESS_BMAC1_MEM :
+ NIG_REG_INGRESS_BMAC0_MEM;
+ u32 wb_data[2];
+ u32 nig_bmac_enable = REG_RD(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4);
+
+ /* Only if the bmac is out of reset */
+ if (REG_RD(bp, MISC_REG_RESET_REG_2) &
+ (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port) &&
+ nig_bmac_enable) {
+
+ /* Clear Rx Enable bit in BMAC_CONTROL register */
+ REG_RD_DMAE(bp, bmac_addr + BIGMAC_REGISTER_BMAC_CONTROL,
+ wb_data, 2);
+ wb_data[0] &= ~BMAC_CONTROL_RX_ENABLE;
+ REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_BMAC_CONTROL,
+ wb_data, 2);
+
+ msleep(1);
+ }
+}
+
+static u8 bnx2x_pbf_update(struct link_params *params, u32 flow_ctrl,
+ u32 line_speed)
+{
+ struct bnx2x *bp = params->bp;
+ u8 port = params->port;
+ u32 init_crd, crd;
+ u32 count = 1000;
+
+ /* disable port */
+ REG_WR(bp, PBF_REG_DISABLE_NEW_TASK_PROC_P0 + port*4, 0x1);
+
+ /* wait for init credit */
+ init_crd = REG_RD(bp, PBF_REG_P0_INIT_CRD + port*4);
+ crd = REG_RD(bp, PBF_REG_P0_CREDIT + port*8);
+ DP(NETIF_MSG_LINK, "init_crd 0x%x crd 0x%x\n", init_crd, crd);
+
+ while ((init_crd != crd) && count) {
+ msleep(5);
+
+ crd = REG_RD(bp, PBF_REG_P0_CREDIT + port*8);
+ count--;
+ }
+ crd = REG_RD(bp, PBF_REG_P0_CREDIT + port*8);
+ if (init_crd != crd) {
+ DP(NETIF_MSG_LINK, "BUG! init_crd 0x%x != crd 0x%x\n",
+ init_crd, crd);
+ return -EINVAL;
+ }
+
+ if (flow_ctrl & BNX2X_FLOW_CTRL_RX ||
+ line_speed == SPEED_10 ||
+ line_speed == SPEED_100 ||
+ line_speed == SPEED_1000 ||
+ line_speed == SPEED_2500) {
+ REG_WR(bp, PBF_REG_P0_PAUSE_ENABLE + port*4, 1);
+ /* update threshold */
+ REG_WR(bp, PBF_REG_P0_ARB_THRSH + port*4, 0);
+ /* update init credit */
+ init_crd = 778; /* (800-18-4) */
+
+ } else {
+ u32 thresh = (ETH_MAX_JUMBO_PACKET_SIZE +
+ ETH_OVREHEAD)/16;
+ REG_WR(bp, PBF_REG_P0_PAUSE_ENABLE + port*4, 0);
+ /* update threshold */
+ REG_WR(bp, PBF_REG_P0_ARB_THRSH + port*4, thresh);
+ /* update init credit */
+ switch (line_speed) {
+ case SPEED_10000:
+ init_crd = thresh + 553 - 22;
+ break;
+
+ case SPEED_12000:
+ init_crd = thresh + 664 - 22;
+ break;
+
+ case SPEED_13000:
+ init_crd = thresh + 742 - 22;
+ break;
+
+ case SPEED_16000:
+ init_crd = thresh + 778 - 22;
+ break;
+ default:
+ DP(NETIF_MSG_LINK, "Invalid line_speed 0x%x\n",
+ line_speed);
+ return -EINVAL;
+ }
+ }
+ REG_WR(bp, PBF_REG_P0_INIT_CRD + port*4, init_crd);
+ DP(NETIF_MSG_LINK, "PBF updated to speed %d credit %d\n",
+ line_speed, init_crd);
+
+ /* probe the credit changes */
+ REG_WR(bp, PBF_REG_INIT_P0 + port*4, 0x1);
+ msleep(5);
+ REG_WR(bp, PBF_REG_INIT_P0 + port*4, 0x0);
+
+ /* enable port */
+ REG_WR(bp, PBF_REG_DISABLE_NEW_TASK_PROC_P0 + port*4, 0x0);
+ return 0;
+}
+
+static u32 bnx2x_get_emac_base(struct bnx2x *bp, u32 ext_phy_type, u8 port)
+{
+ u32 emac_base;
+
+ switch (ext_phy_type) {
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072:
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726:
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727:
+ /* All MDC/MDIO is directed through single EMAC */
+ if (REG_RD(bp, NIG_REG_PORT_SWAP))
+ emac_base = GRCBASE_EMAC0;
+ else
+ emac_base = GRCBASE_EMAC1;
+ break;
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073:
+ emac_base = (port) ? GRCBASE_EMAC0 : GRCBASE_EMAC1;
+ break;
+ default:
+ emac_base = (port) ? GRCBASE_EMAC1 : GRCBASE_EMAC0;
+ break;
+ }
+ return emac_base;
+
+}
+
+u8 bnx2x_cl45_write(struct bnx2x *bp, u8 port, u32 ext_phy_type,
+ u8 phy_addr, u8 devad, u16 reg, u16 val)
+{
+ u32 tmp, saved_mode;
+ u8 i, rc = 0;
+ u32 mdio_ctrl = bnx2x_get_emac_base(bp, ext_phy_type, port);
+
+ /* set clause 45 mode, slow down the MDIO clock to 2.5MHz
+ * (a value of 49==0x31) and make sure that the AUTO poll is off
+ */
+
+ saved_mode = REG_RD(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE);
+ tmp = saved_mode & ~(EMAC_MDIO_MODE_AUTO_POLL |
+ EMAC_MDIO_MODE_CLOCK_CNT);
+ tmp |= (EMAC_MDIO_MODE_CLAUSE_45 |
+ (49 << EMAC_MDIO_MODE_CLOCK_CNT_BITSHIFT));
+ REG_WR(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE, tmp);
+ REG_RD(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE);
+ udelay(40);
+
+ /* address */
+
+ tmp = ((phy_addr << 21) | (devad << 16) | reg |
+ EMAC_MDIO_COMM_COMMAND_ADDRESS |
+ EMAC_MDIO_COMM_START_BUSY);
+ REG_WR(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM, tmp);
+
+ for (i = 0; i < 50; i++) {
+ udelay(10);
+
+ tmp = REG_RD(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM);
+ if (!(tmp & EMAC_MDIO_COMM_START_BUSY)) {
+ udelay(5);
+ break;
+ }
+ }
+ if (tmp & EMAC_MDIO_COMM_START_BUSY) {
+ DP(NETIF_MSG_LINK, "write phy register failed\n");
+ rc = -EFAULT;
+ } else {
+ /* data */
+ tmp = ((phy_addr << 21) | (devad << 16) | val |
+ EMAC_MDIO_COMM_COMMAND_WRITE_45 |
+ EMAC_MDIO_COMM_START_BUSY);
+ REG_WR(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM, tmp);
+
+ for (i = 0; i < 50; i++) {
+ udelay(10);
+
+ tmp = REG_RD(bp, mdio_ctrl +
+ EMAC_REG_EMAC_MDIO_COMM);
+ if (!(tmp & EMAC_MDIO_COMM_START_BUSY)) {
+ udelay(5);
+ break;
+ }
+ }
+ if (tmp & EMAC_MDIO_COMM_START_BUSY) {
+ DP(NETIF_MSG_LINK, "write phy register failed\n");
+ rc = -EFAULT;
+ }
+ }
+
+ /* Restore the saved mode */
+ REG_WR(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE, saved_mode);
+
+ return rc;
+}
+
+u8 bnx2x_cl45_read(struct bnx2x *bp, u8 port, u32 ext_phy_type,
+ u8 phy_addr, u8 devad, u16 reg, u16 *ret_val)
+{
+ u32 val, saved_mode;
+ u16 i;
+ u8 rc = 0;
+
+ u32 mdio_ctrl = bnx2x_get_emac_base(bp, ext_phy_type, port);
+ /* set clause 45 mode, slow down the MDIO clock to 2.5MHz
+ * (a value of 49==0x31) and make sure that the AUTO poll is off
+ */
+
+ saved_mode = REG_RD(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE);
+ val = saved_mode & ((EMAC_MDIO_MODE_AUTO_POLL |
+ EMAC_MDIO_MODE_CLOCK_CNT));
+ val |= (EMAC_MDIO_MODE_CLAUSE_45 |
+ (49L << EMAC_MDIO_MODE_CLOCK_CNT_BITSHIFT));
+ REG_WR(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE, val);
+ REG_RD(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE);
+ udelay(40);
+
+ /* address */
+ val = ((phy_addr << 21) | (devad << 16) | reg |
+ EMAC_MDIO_COMM_COMMAND_ADDRESS |
+ EMAC_MDIO_COMM_START_BUSY);
+ REG_WR(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM, val);
+
+ for (i = 0; i < 50; i++) {
+ udelay(10);
+
+ val = REG_RD(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM);
+ if (!(val & EMAC_MDIO_COMM_START_BUSY)) {
+ udelay(5);
+ break;
+ }
+ }
+ if (val & EMAC_MDIO_COMM_START_BUSY) {
+ DP(NETIF_MSG_LINK, "read phy register failed\n");
+
+ *ret_val = 0;
+ rc = -EFAULT;
+
+ } else {
+ /* data */
+ val = ((phy_addr << 21) | (devad << 16) |
+ EMAC_MDIO_COMM_COMMAND_READ_45 |
+ EMAC_MDIO_COMM_START_BUSY);
+ REG_WR(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM, val);
+
+ for (i = 0; i < 50; i++) {
+ udelay(10);
+
+ val = REG_RD(bp, mdio_ctrl +
+ EMAC_REG_EMAC_MDIO_COMM);
+ if (!(val & EMAC_MDIO_COMM_START_BUSY)) {
+ *ret_val = (u16)(val & EMAC_MDIO_COMM_DATA);
+ break;
+ }
+ }
+ if (val & EMAC_MDIO_COMM_START_BUSY) {
+ DP(NETIF_MSG_LINK, "read phy register failed\n");
+
+ *ret_val = 0;
+ rc = -EFAULT;
+ }
+ }
+
+ /* Restore the saved mode */
+ REG_WR(bp, mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE, saved_mode);
+
+ return rc;
+}
+
+static void bnx2x_set_aer_mmd(struct link_params *params,
+ struct link_vars *vars)
+{
+ struct bnx2x *bp = params->bp;
+ u32 ser_lane;
+ u16 offset;
+
+ ser_lane = ((params->lane_config &
+ PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >>
+ PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT);
+
+ offset = (vars->phy_flags & PHY_XGXS_FLAG) ?
+ (params->phy_addr + ser_lane) : 0;
+
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_AER_BLOCK,
+ MDIO_AER_BLOCK_AER_REG, 0x3800 + offset);
+}
+
+static void bnx2x_set_master_ln(struct link_params *params)
+{
+ struct bnx2x *bp = params->bp;
+ u16 new_master_ln, ser_lane;
+ ser_lane = ((params->lane_config &
+ PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >>
+ PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT);
+
+ /* set the master_ln for AN */
+ CL45_RD_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_XGXS_BLOCK2,
+ MDIO_XGXS_BLOCK2_TEST_MODE_LANE,
+ &new_master_ln);
+
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_XGXS_BLOCK2 ,
+ MDIO_XGXS_BLOCK2_TEST_MODE_LANE,
+ (new_master_ln | ser_lane));
+}
+
+static u8 bnx2x_reset_unicore(struct link_params *params)
+{
+ struct bnx2x *bp = params->bp;
+ u16 mii_control;
+ u16 i;
+
+ CL45_RD_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_COMBO_IEEE0,
+ MDIO_COMBO_IEEE0_MII_CONTROL, &mii_control);
+
+ /* reset the unicore */
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_COMBO_IEEE0,
+ MDIO_COMBO_IEEE0_MII_CONTROL,
+ (mii_control |
+ MDIO_COMBO_IEEO_MII_CONTROL_RESET));
+ if (params->switch_cfg == SWITCH_CFG_1G)
+ bnx2x_set_serdes_access(params);
+
+ /* wait for the reset to self clear */
+ for (i = 0; i < MDIO_ACCESS_TIMEOUT; i++) {
+ udelay(5);
+
+ /* the reset erased the previous bank value */
+ CL45_RD_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_COMBO_IEEE0,
+ MDIO_COMBO_IEEE0_MII_CONTROL,
+ &mii_control);
+
+ if (!(mii_control & MDIO_COMBO_IEEO_MII_CONTROL_RESET)) {
+ udelay(5);
+ return 0;
+ }
+ }
+
+ DP(NETIF_MSG_LINK, "BUG! XGXS is still in reset!\n");
+ return -EINVAL;
+
+}
+
+static void bnx2x_set_swap_lanes(struct link_params *params)
+{
+ struct bnx2x *bp = params->bp;
+ /* Each two bits represents a lane number:
+ No swap is 0123 => 0x1b no need to enable the swap */
+ u16 ser_lane, rx_lane_swap, tx_lane_swap;
+
+ ser_lane = ((params->lane_config &
+ PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >>
+ PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT);
+ rx_lane_swap = ((params->lane_config &
+ PORT_HW_CFG_LANE_SWAP_CFG_RX_MASK) >>
+ PORT_HW_CFG_LANE_SWAP_CFG_RX_SHIFT);
+ tx_lane_swap = ((params->lane_config &
+ PORT_HW_CFG_LANE_SWAP_CFG_TX_MASK) >>
+ PORT_HW_CFG_LANE_SWAP_CFG_TX_SHIFT);
+
+ if (rx_lane_swap != 0x1b) {
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_XGXS_BLOCK2,
+ MDIO_XGXS_BLOCK2_RX_LN_SWAP,
+ (rx_lane_swap |
+ MDIO_XGXS_BLOCK2_RX_LN_SWAP_ENABLE |
+ MDIO_XGXS_BLOCK2_RX_LN_SWAP_FORCE_ENABLE));
+ } else {
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_XGXS_BLOCK2,
+ MDIO_XGXS_BLOCK2_RX_LN_SWAP, 0);
+ }
+
+ if (tx_lane_swap != 0x1b) {
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_XGXS_BLOCK2,
+ MDIO_XGXS_BLOCK2_TX_LN_SWAP,
+ (tx_lane_swap |
+ MDIO_XGXS_BLOCK2_TX_LN_SWAP_ENABLE));
+ } else {
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_XGXS_BLOCK2,
+ MDIO_XGXS_BLOCK2_TX_LN_SWAP, 0);
+ }
+}
+
+static void bnx2x_set_parallel_detection(struct link_params *params,
+ u8 phy_flags)
+{
+ struct bnx2x *bp = params->bp;
+ u16 control2;
+
+ CL45_RD_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_SERDES_DIGITAL,
+ MDIO_SERDES_DIGITAL_A_1000X_CONTROL2,
+ &control2);
+ if (params->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_1G)
+ control2 |= MDIO_SERDES_DIGITAL_A_1000X_CONTROL2_PRL_DT_EN;
+ else
+ control2 &= ~MDIO_SERDES_DIGITAL_A_1000X_CONTROL2_PRL_DT_EN;
+ DP(NETIF_MSG_LINK, "params->speed_cap_mask = 0x%x, control2 = 0x%x\n",
+ params->speed_cap_mask, control2);
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_SERDES_DIGITAL,
+ MDIO_SERDES_DIGITAL_A_1000X_CONTROL2,
+ control2);
+
+ if ((phy_flags & PHY_XGXS_FLAG) &&
+ (params->speed_cap_mask &
+ PORT_HW_CFG_SPEED_CAPABILITY_D0_10G)) {
+ DP(NETIF_MSG_LINK, "XGXS\n");
+
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_10G_PARALLEL_DETECT,
+ MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_LINK,
+ MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_LINK_CNT);
+
+ CL45_RD_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_10G_PARALLEL_DETECT,
+ MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL,
+ &control2);
+
+
+ control2 |=
+ MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL_PARDET10G_EN;
+
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_10G_PARALLEL_DETECT,
+ MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL,
+ control2);
+
+ /* Disable parallel detection of HiG */
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_XGXS_BLOCK2,
+ MDIO_XGXS_BLOCK2_UNICORE_MODE_10G,
+ MDIO_XGXS_BLOCK2_UNICORE_MODE_10G_CX4_XGXS |
+ MDIO_XGXS_BLOCK2_UNICORE_MODE_10G_HIGIG_XGXS);
+ }
+}
+
+static void bnx2x_set_autoneg(struct link_params *params,
+ struct link_vars *vars,
+ u8 enable_cl73)
+{
+ struct bnx2x *bp = params->bp;
+ u16 reg_val;
+
+ /* CL37 Autoneg */
+
+ CL45_RD_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_COMBO_IEEE0,
+ MDIO_COMBO_IEEE0_MII_CONTROL, &reg_val);
+
+ /* CL37 Autoneg Enabled */
+ if (vars->line_speed == SPEED_AUTO_NEG)
+ reg_val |= MDIO_COMBO_IEEO_MII_CONTROL_AN_EN;
+ else /* CL37 Autoneg Disabled */
+ reg_val &= ~(MDIO_COMBO_IEEO_MII_CONTROL_AN_EN |
+ MDIO_COMBO_IEEO_MII_CONTROL_RESTART_AN);
+
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_COMBO_IEEE0,
+ MDIO_COMBO_IEEE0_MII_CONTROL, reg_val);
+
+ /* Enable/Disable Autodetection */
+
+ CL45_RD_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_SERDES_DIGITAL,
+ MDIO_SERDES_DIGITAL_A_1000X_CONTROL1, &reg_val);
+ reg_val &= ~(MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_SIGNAL_DETECT_EN |
+ MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_INVERT_SIGNAL_DETECT);
+ reg_val |= MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_FIBER_MODE;
+ if (vars->line_speed == SPEED_AUTO_NEG)
+ reg_val |= MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET;
+ else
+ reg_val &= ~MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET;
+
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_SERDES_DIGITAL,
+ MDIO_SERDES_DIGITAL_A_1000X_CONTROL1, reg_val);
+
+ /* Enable TetonII and BAM autoneg */
+ CL45_RD_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_BAM_NEXT_PAGE,
+ MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL,
+ &reg_val);
+ if (vars->line_speed == SPEED_AUTO_NEG) {
+ /* Enable BAM aneg Mode and TetonII aneg Mode */
+ reg_val |= (MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_BAM_MODE |
+ MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_TETON_AN);
+ } else {
+ /* TetonII and BAM Autoneg Disabled */
+ reg_val &= ~(MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_BAM_MODE |
+ MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_TETON_AN);
+ }
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_BAM_NEXT_PAGE,
+ MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL,
+ reg_val);
+
+ if (enable_cl73) {
+ /* Enable Cl73 FSM status bits */
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_CL73_USERB0,
+ MDIO_CL73_USERB0_CL73_UCTRL,
+ 0xe);
+
+ /* Enable BAM Station Manager*/
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_CL73_USERB0,
+ MDIO_CL73_USERB0_CL73_BAM_CTRL1,
+ MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_EN |
+ MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_STATION_MNGR_EN |
+ MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_NP_AFTER_BP_EN);
+
+ /* Advertise CL73 link speeds */
+ CL45_RD_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_CL73_IEEEB1,
+ MDIO_CL73_IEEEB1_AN_ADV2,
+ &reg_val);
+ if (params->speed_cap_mask &
+ PORT_HW_CFG_SPEED_CAPABILITY_D0_10G)
+ reg_val |= MDIO_CL73_IEEEB1_AN_ADV2_ADVR_10G_KX4;
+ if (params->speed_cap_mask &
+ PORT_HW_CFG_SPEED_CAPABILITY_D0_1G)
+ reg_val |= MDIO_CL73_IEEEB1_AN_ADV2_ADVR_1000M_KX;
+
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_CL73_IEEEB1,
+ MDIO_CL73_IEEEB1_AN_ADV2,
+ reg_val);
+
+ /* CL73 Autoneg Enabled */
+ reg_val = MDIO_CL73_IEEEB0_CL73_AN_CONTROL_AN_EN;
+
+ } else /* CL73 Autoneg Disabled */
+ reg_val = 0;
+
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_CL73_IEEEB0,
+ MDIO_CL73_IEEEB0_CL73_AN_CONTROL, reg_val);
+}
+
+/* program SerDes, forced speed */
+static void bnx2x_program_serdes(struct link_params *params,
+ struct link_vars *vars)
+{
+ struct bnx2x *bp = params->bp;
+ u16 reg_val;
+
+ /* program duplex, disable autoneg and sgmii*/
+ CL45_RD_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_COMBO_IEEE0,
+ MDIO_COMBO_IEEE0_MII_CONTROL, &reg_val);
+ reg_val &= ~(MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX |
+ MDIO_COMBO_IEEO_MII_CONTROL_AN_EN |
+ MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_MASK);
+ if (params->req_duplex == DUPLEX_FULL)
+ reg_val |= MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX;
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_COMBO_IEEE0,
+ MDIO_COMBO_IEEE0_MII_CONTROL, reg_val);
+
+ /* program speed
+ - needed only if the speed is greater than 1G (2.5G or 10G) */
+ CL45_RD_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_SERDES_DIGITAL,
+ MDIO_SERDES_DIGITAL_MISC1, &reg_val);
+ /* clearing the speed value before setting the right speed */
+ DP(NETIF_MSG_LINK, "MDIO_REG_BANK_SERDES_DIGITAL = 0x%x\n", reg_val);
+
+ reg_val &= ~(MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_MASK |
+ MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_SEL);
+
+ if (!((vars->line_speed == SPEED_1000) ||
+ (vars->line_speed == SPEED_100) ||
+ (vars->line_speed == SPEED_10))) {
+
+ reg_val |= (MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_156_25M |
+ MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_SEL);
+ if (vars->line_speed == SPEED_10000)
+ reg_val |=
+ MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_10G_CX4;
+ if (vars->line_speed == SPEED_13000)
+ reg_val |=
+ MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_13G;
+ }
+
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_SERDES_DIGITAL,
+ MDIO_SERDES_DIGITAL_MISC1, reg_val);
+
+}
+
+static void bnx2x_set_brcm_cl37_advertisment(struct link_params *params)
+{
+ struct bnx2x *bp = params->bp;
+ u16 val = 0;
+
+ /* configure the 48 bits for BAM AN */
+
+ /* set extended capabilities */
+ if (params->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_2_5G)
+ val |= MDIO_OVER_1G_UP1_2_5G;
+ if (params->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_10G)
+ val |= MDIO_OVER_1G_UP1_10G;
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_OVER_1G,
+ MDIO_OVER_1G_UP1, val);
+
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_OVER_1G,
+ MDIO_OVER_1G_UP3, 0x400);
+}
+
+static void bnx2x_calc_ieee_aneg_adv(struct link_params *params, u16 *ieee_fc)
+{
+ struct bnx2x *bp = params->bp;
+ *ieee_fc = MDIO_COMBO_IEEE0_AUTO_NEG_ADV_FULL_DUPLEX;
+ /* resolve pause mode and advertisement
+ * Please refer to Table 28B-3 of the 802.3ab-1999 spec */
+
+ switch (params->req_flow_ctrl) {
+ case BNX2X_FLOW_CTRL_AUTO:
+ if (params->req_fc_auto_adv == BNX2X_FLOW_CTRL_BOTH) {
+ *ieee_fc |=
+ MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH;
+ } else {
+ *ieee_fc |=
+ MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC;
+ }
+ break;
+ case BNX2X_FLOW_CTRL_TX:
+ *ieee_fc |=
+ MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC;
+ break;
+
+ case BNX2X_FLOW_CTRL_RX:
+ case BNX2X_FLOW_CTRL_BOTH:
+ *ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH;
+ break;
+
+ case BNX2X_FLOW_CTRL_NONE:
+ default:
+ *ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_NONE;
+ break;
+ }
+ DP(NETIF_MSG_LINK, "ieee_fc = 0x%x\n", *ieee_fc);
+}
+
+static void bnx2x_set_ieee_aneg_advertisment(struct link_params *params,
+ u16 ieee_fc)
+{
+ struct bnx2x *bp = params->bp;
+ u16 val;
+ /* for AN, we are always publishing full duplex */
+
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_COMBO_IEEE0,
+ MDIO_COMBO_IEEE0_AUTO_NEG_ADV, ieee_fc);
+ CL45_RD_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_CL73_IEEEB1,
+ MDIO_CL73_IEEEB1_AN_ADV1, &val);
+ val &= ~MDIO_CL73_IEEEB1_AN_ADV1_PAUSE_BOTH;
+ val |= ((ieee_fc<<3) & MDIO_CL73_IEEEB1_AN_ADV1_PAUSE_MASK);
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_CL73_IEEEB1,
+ MDIO_CL73_IEEEB1_AN_ADV1, val);
+}
+
+static void bnx2x_restart_autoneg(struct link_params *params, u8 enable_cl73)
+{
+ struct bnx2x *bp = params->bp;
+ u16 mii_control;
+
+ DP(NETIF_MSG_LINK, "bnx2x_restart_autoneg\n");
+ /* Enable and restart BAM/CL37 aneg */
+
+ if (enable_cl73) {
+ CL45_RD_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_CL73_IEEEB0,
+ MDIO_CL73_IEEEB0_CL73_AN_CONTROL,
+ &mii_control);
+
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_CL73_IEEEB0,
+ MDIO_CL73_IEEEB0_CL73_AN_CONTROL,
+ (mii_control |
+ MDIO_CL73_IEEEB0_CL73_AN_CONTROL_AN_EN |
+ MDIO_CL73_IEEEB0_CL73_AN_CONTROL_RESTART_AN));
+ } else {
+
+ CL45_RD_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_COMBO_IEEE0,
+ MDIO_COMBO_IEEE0_MII_CONTROL,
+ &mii_control);
+ DP(NETIF_MSG_LINK,
+ "bnx2x_restart_autoneg mii_control before = 0x%x\n",
+ mii_control);
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_COMBO_IEEE0,
+ MDIO_COMBO_IEEE0_MII_CONTROL,
+ (mii_control |
+ MDIO_COMBO_IEEO_MII_CONTROL_AN_EN |
+ MDIO_COMBO_IEEO_MII_CONTROL_RESTART_AN));
+ }
+}
+
+static void bnx2x_initialize_sgmii_process(struct link_params *params,
+ struct link_vars *vars)
+{
+ struct bnx2x *bp = params->bp;
+ u16 control1;
+
+ /* in SGMII mode, the unicore is always slave */
+
+ CL45_RD_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_SERDES_DIGITAL,
+ MDIO_SERDES_DIGITAL_A_1000X_CONTROL1,
+ &control1);
+ control1 |= MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_INVERT_SIGNAL_DETECT;
+ /* set sgmii mode (and not fiber) */
+ control1 &= ~(MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_FIBER_MODE |
+ MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET |
+ MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_MSTR_MODE);
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_SERDES_DIGITAL,
+ MDIO_SERDES_DIGITAL_A_1000X_CONTROL1,
+ control1);
+
+ /* if forced speed */
+ if (!(vars->line_speed == SPEED_AUTO_NEG)) {
+ /* set speed, disable autoneg */
+ u16 mii_control;
+
+ CL45_RD_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_COMBO_IEEE0,
+ MDIO_COMBO_IEEE0_MII_CONTROL,
+ &mii_control);
+ mii_control &= ~(MDIO_COMBO_IEEO_MII_CONTROL_AN_EN |
+ MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_MASK|
+ MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX);
+
+ switch (vars->line_speed) {
+ case SPEED_100:
+ mii_control |=
+ MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_100;
+ break;
+ case SPEED_1000:
+ mii_control |=
+ MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_1000;
+ break;
+ case SPEED_10:
+ /* there is nothing to set for 10M */
+ break;
+ default:
+ /* invalid speed for SGMII */
+ DP(NETIF_MSG_LINK, "Invalid line_speed 0x%x\n",
+ vars->line_speed);
+ break;
+ }
+
+ /* setting the full duplex */
+ if (params->req_duplex == DUPLEX_FULL)
+ mii_control |=
+ MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX;
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_COMBO_IEEE0,
+ MDIO_COMBO_IEEE0_MII_CONTROL,
+ mii_control);
+
+ } else { /* AN mode */
+ /* enable and restart AN */
+ bnx2x_restart_autoneg(params, 0);
+ }
+}
+
+
+/*
+ * link management
+ */
+
+static void bnx2x_pause_resolve(struct link_vars *vars, u32 pause_result)
+{ /* LD LP */
+ switch (pause_result) { /* ASYM P ASYM P */
+ case 0xb: /* 1 0 1 1 */
+ vars->flow_ctrl = BNX2X_FLOW_CTRL_TX;
+ break;
+
+ case 0xe: /* 1 1 1 0 */
+ vars->flow_ctrl = BNX2X_FLOW_CTRL_RX;
+ break;
+
+ case 0x5: /* 0 1 0 1 */
+ case 0x7: /* 0 1 1 1 */
+ case 0xd: /* 1 1 0 1 */
+ case 0xf: /* 1 1 1 1 */
+ vars->flow_ctrl = BNX2X_FLOW_CTRL_BOTH;
+ break;
+
+ default:
+ break;
+ }
+}
+
+static u8 bnx2x_ext_phy_resolve_fc(struct link_params *params,
+ struct link_vars *vars)
+{
+ struct bnx2x *bp = params->bp;
+ u8 ext_phy_addr;
+ u16 ld_pause; /* local */
+ u16 lp_pause; /* link partner */
+ u16 an_complete; /* AN complete */
+ u16 pause_result;
+ u8 ret = 0;
+ u32 ext_phy_type;
+ u8 port = params->port;
+ ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config);
+ ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config);
+ /* read twice */
+
+ bnx2x_cl45_read(bp, port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_STATUS, &an_complete);
+ bnx2x_cl45_read(bp, port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_STATUS, &an_complete);
+
+ if (an_complete & MDIO_AN_REG_STATUS_AN_COMPLETE) {
+ ret = 1;
+ bnx2x_cl45_read(bp, port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_ADV_PAUSE, &ld_pause);
+ bnx2x_cl45_read(bp, port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_LP_AUTO_NEG, &lp_pause);
+ pause_result = (ld_pause &
+ MDIO_AN_REG_ADV_PAUSE_MASK) >> 8;
+ pause_result |= (lp_pause &
+ MDIO_AN_REG_ADV_PAUSE_MASK) >> 10;
+ DP(NETIF_MSG_LINK, "Ext PHY pause result 0x%x\n",
+ pause_result);
+ bnx2x_pause_resolve(vars, pause_result);
+ if (vars->flow_ctrl == BNX2X_FLOW_CTRL_NONE &&
+ ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073) {
+ bnx2x_cl45_read(bp, port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_CL37_FC_LD, &ld_pause);
+
+ bnx2x_cl45_read(bp, port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_CL37_FC_LP, &lp_pause);
+ pause_result = (ld_pause &
+ MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) >> 5;
+ pause_result |= (lp_pause &
+ MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) >> 7;
+
+ bnx2x_pause_resolve(vars, pause_result);
+ DP(NETIF_MSG_LINK, "Ext PHY CL37 pause result 0x%x\n",
+ pause_result);
+ }
+ }
+ return ret;
+}
+
+static u8 bnx2x_direct_parallel_detect_used(struct link_params *params)
+{
+ struct bnx2x *bp = params->bp;
+ u16 pd_10g, status2_1000x;
+ CL45_RD_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_SERDES_DIGITAL,
+ MDIO_SERDES_DIGITAL_A_1000X_STATUS2,
+ &status2_1000x);
+ CL45_RD_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_SERDES_DIGITAL,
+ MDIO_SERDES_DIGITAL_A_1000X_STATUS2,
+ &status2_1000x);
+ if (status2_1000x & MDIO_SERDES_DIGITAL_A_1000X_STATUS2_AN_DISABLED) {
+ DP(NETIF_MSG_LINK, "1G parallel detect link on port %d\n",
+ params->port);
+ return 1;
+ }
+
+ CL45_RD_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_10G_PARALLEL_DETECT,
+ MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_STATUS,
+ &pd_10g);
+
+ if (pd_10g & MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_STATUS_PD_LINK) {
+ DP(NETIF_MSG_LINK, "10G parallel detect link on port %d\n",
+ params->port);
+ return 1;
+ }
+ return 0;
+}
+
+static void bnx2x_flow_ctrl_resolve(struct link_params *params,
+ struct link_vars *vars,
+ u32 gp_status)
+{
+ struct bnx2x *bp = params->bp;
+ u16 ld_pause; /* local driver */
+ u16 lp_pause; /* link partner */
+ u16 pause_result;
+
+ vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE;
+
+ /* resolve from gp_status in case of AN complete and not sgmii */
+ if ((params->req_flow_ctrl == BNX2X_FLOW_CTRL_AUTO) &&
+ (gp_status & MDIO_AN_CL73_OR_37_COMPLETE) &&
+ (!(vars->phy_flags & PHY_SGMII_FLAG)) &&
+ (XGXS_EXT_PHY_TYPE(params->ext_phy_config) ==
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT)) {
+ if (bnx2x_direct_parallel_detect_used(params)) {
+ vars->flow_ctrl = params->req_fc_auto_adv;
+ return;
+ }
+ if ((gp_status &
+ (MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_AUTONEG_COMPLETE |
+ MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_MR_LP_NP_AN_ABLE)) ==
+ (MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_AUTONEG_COMPLETE |
+ MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_MR_LP_NP_AN_ABLE)) {
+
+ CL45_RD_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_CL73_IEEEB1,
+ MDIO_CL73_IEEEB1_AN_ADV1,
+ &ld_pause);
+ CL45_RD_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_CL73_IEEEB1,
+ MDIO_CL73_IEEEB1_AN_LP_ADV1,
+ &lp_pause);
+ pause_result = (ld_pause &
+ MDIO_CL73_IEEEB1_AN_ADV1_PAUSE_MASK)
+ >> 8;
+ pause_result |= (lp_pause &
+ MDIO_CL73_IEEEB1_AN_LP_ADV1_PAUSE_MASK)
+ >> 10;
+ DP(NETIF_MSG_LINK, "pause_result CL73 0x%x\n",
+ pause_result);
+ } else {
+
+ CL45_RD_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_COMBO_IEEE0,
+ MDIO_COMBO_IEEE0_AUTO_NEG_ADV,
+ &ld_pause);
+ CL45_RD_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_COMBO_IEEE0,
+ MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1,
+ &lp_pause);
+ pause_result = (ld_pause &
+ MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_MASK)>>5;
+ pause_result |= (lp_pause &
+ MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_MASK)>>7;
+ DP(NETIF_MSG_LINK, "pause_result CL37 0x%x\n",
+ pause_result);
+ }
+ bnx2x_pause_resolve(vars, pause_result);
+ } else if ((params->req_flow_ctrl == BNX2X_FLOW_CTRL_AUTO) &&
+ (bnx2x_ext_phy_resolve_fc(params, vars))) {
+ return;
+ } else {
+ if (params->req_flow_ctrl == BNX2X_FLOW_CTRL_AUTO)
+ vars->flow_ctrl = params->req_fc_auto_adv;
+ else
+ vars->flow_ctrl = params->req_flow_ctrl;
+ }
+ DP(NETIF_MSG_LINK, "flow_ctrl 0x%x\n", vars->flow_ctrl);
+}
+
+static void bnx2x_check_fallback_to_cl37(struct link_params *params)
+{
+ struct bnx2x *bp = params->bp;
+ u16 rx_status, ustat_val, cl37_fsm_recieved;
+ DP(NETIF_MSG_LINK, "bnx2x_check_fallback_to_cl37\n");
+ /* Step 1: Make sure signal is detected */
+ CL45_RD_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_RX0,
+ MDIO_RX0_RX_STATUS,
+ &rx_status);
+ if ((rx_status & MDIO_RX0_RX_STATUS_SIGDET) !=
+ (MDIO_RX0_RX_STATUS_SIGDET)) {
+ DP(NETIF_MSG_LINK, "Signal is not detected. Restoring CL73."
+ "rx_status(0x80b0) = 0x%x\n", rx_status);
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_CL73_IEEEB0,
+ MDIO_CL73_IEEEB0_CL73_AN_CONTROL,
+ MDIO_CL73_IEEEB0_CL73_AN_CONTROL_AN_EN);
+ return;
+ }
+ /* Step 2: Check CL73 state machine */
+ CL45_RD_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_CL73_USERB0,
+ MDIO_CL73_USERB0_CL73_USTAT1,
+ &ustat_val);
+ if ((ustat_val &
+ (MDIO_CL73_USERB0_CL73_USTAT1_LINK_STATUS_CHECK |
+ MDIO_CL73_USERB0_CL73_USTAT1_AN_GOOD_CHECK_BAM37)) !=
+ (MDIO_CL73_USERB0_CL73_USTAT1_LINK_STATUS_CHECK |
+ MDIO_CL73_USERB0_CL73_USTAT1_AN_GOOD_CHECK_BAM37)) {
+ DP(NETIF_MSG_LINK, "CL73 state-machine is not stable. "
+ "ustat_val(0x8371) = 0x%x\n", ustat_val);
+ return;
+ }
+ /* Step 3: Check CL37 Message Pages received to indicate LP
+ supports only CL37 */
+ CL45_RD_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_REMOTE_PHY,
+ MDIO_REMOTE_PHY_MISC_RX_STATUS,
+ &cl37_fsm_recieved);
+ if ((cl37_fsm_recieved &
+ (MDIO_REMOTE_PHY_MISC_RX_STATUS_CL37_FSM_RECEIVED_OVER1G_MSG |
+ MDIO_REMOTE_PHY_MISC_RX_STATUS_CL37_FSM_RECEIVED_BRCM_OUI_MSG)) !=
+ (MDIO_REMOTE_PHY_MISC_RX_STATUS_CL37_FSM_RECEIVED_OVER1G_MSG |
+ MDIO_REMOTE_PHY_MISC_RX_STATUS_CL37_FSM_RECEIVED_BRCM_OUI_MSG)) {
+ DP(NETIF_MSG_LINK, "No CL37 FSM were received. "
+ "misc_rx_status(0x8330) = 0x%x\n",
+ cl37_fsm_recieved);
+ return;
+ }
+ /* The combined cl37/cl73 fsm state information indicating that we are
+ connected to a device which does not support cl73, but does support
+ cl37 BAM. In this case we disable cl73 and restart cl37 auto-neg */
+ /* Disable CL73 */
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_CL73_IEEEB0,
+ MDIO_CL73_IEEEB0_CL73_AN_CONTROL,
+ 0);
+ /* Restart CL37 autoneg */
+ bnx2x_restart_autoneg(params, 0);
+ DP(NETIF_MSG_LINK, "Disabling CL73, and restarting CL37 autoneg\n");
+}
+static u8 bnx2x_link_settings_status(struct link_params *params,
+ struct link_vars *vars,
+ u32 gp_status,
+ u8 ext_phy_link_up)
+{
+ struct bnx2x *bp = params->bp;
+ u16 new_line_speed;
+ u8 rc = 0;
+ vars->link_status = 0;
+
+ if (gp_status & MDIO_GP_STATUS_TOP_AN_STATUS1_LINK_STATUS) {
+ DP(NETIF_MSG_LINK, "phy link up gp_status=0x%x\n",
+ gp_status);
+
+ vars->phy_link_up = 1;
+ vars->link_status |= LINK_STATUS_LINK_UP;
+
+ if (gp_status & MDIO_GP_STATUS_TOP_AN_STATUS1_DUPLEX_STATUS)
+ vars->duplex = DUPLEX_FULL;
+ else
+ vars->duplex = DUPLEX_HALF;
+
+ bnx2x_flow_ctrl_resolve(params, vars, gp_status);
+
+ switch (gp_status & GP_STATUS_SPEED_MASK) {
+ case GP_STATUS_10M:
+ new_line_speed = SPEED_10;
+ if (vars->duplex == DUPLEX_FULL)
+ vars->link_status |= LINK_10TFD;
+ else
+ vars->link_status |= LINK_10THD;
+ break;
+
+ case GP_STATUS_100M:
+ new_line_speed = SPEED_100;
+ if (vars->duplex == DUPLEX_FULL)
+ vars->link_status |= LINK_100TXFD;
+ else
+ vars->link_status |= LINK_100TXHD;
+ break;
+
+ case GP_STATUS_1G:
+ case GP_STATUS_1G_KX:
+ new_line_speed = SPEED_1000;
+ if (vars->duplex == DUPLEX_FULL)
+ vars->link_status |= LINK_1000TFD;
+ else
+ vars->link_status |= LINK_1000THD;
+ break;
+
+ case GP_STATUS_2_5G:
+ new_line_speed = SPEED_2500;
+ if (vars->duplex == DUPLEX_FULL)
+ vars->link_status |= LINK_2500TFD;
+ else
+ vars->link_status |= LINK_2500THD;
+ break;
+
+ case GP_STATUS_5G:
+ case GP_STATUS_6G:
+ DP(NETIF_MSG_LINK,
+ "link speed unsupported gp_status 0x%x\n",
+ gp_status);
+ return -EINVAL;
+
+ case GP_STATUS_10G_KX4:
+ case GP_STATUS_10G_HIG:
+ case GP_STATUS_10G_CX4:
+ new_line_speed = SPEED_10000;
+ vars->link_status |= LINK_10GTFD;
+ break;
+
+ case GP_STATUS_12G_HIG:
+ new_line_speed = SPEED_12000;
+ vars->link_status |= LINK_12GTFD;
+ break;
+
+ case GP_STATUS_12_5G:
+ new_line_speed = SPEED_12500;
+ vars->link_status |= LINK_12_5GTFD;
+ break;
+
+ case GP_STATUS_13G:
+ new_line_speed = SPEED_13000;
+ vars->link_status |= LINK_13GTFD;
+ break;
+
+ case GP_STATUS_15G:
+ new_line_speed = SPEED_15000;
+ vars->link_status |= LINK_15GTFD;
+ break;
+
+ case GP_STATUS_16G:
+ new_line_speed = SPEED_16000;
+ vars->link_status |= LINK_16GTFD;
+ break;
+
+ default:
+ DP(NETIF_MSG_LINK,
+ "link speed unsupported gp_status 0x%x\n",
+ gp_status);
+ return -EINVAL;
+ }
+
+ /* Upon link speed change set the NIG into drain mode.
+ Comes to deals with possible FIFO glitch due to clk change
+ when speed is decreased without link down indicator */
+ if (new_line_speed != vars->line_speed) {
+ if (XGXS_EXT_PHY_TYPE(params->ext_phy_config) !=
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT &&
+ ext_phy_link_up) {
+ DP(NETIF_MSG_LINK, "Internal link speed %d is"
+ " different than the external"
+ " link speed %d\n", new_line_speed,
+ vars->line_speed);
+ vars->phy_link_up = 0;
+ return 0;
+ }
+ REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE
+ + params->port*4, 0);
+ msleep(1);
+ }
+ vars->line_speed = new_line_speed;
+ vars->link_status |= LINK_STATUS_SERDES_LINK;
+
+ if ((params->req_line_speed == SPEED_AUTO_NEG) &&
+ ((XGXS_EXT_PHY_TYPE(params->ext_phy_config) ==
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) ||
+ (XGXS_EXT_PHY_TYPE(params->ext_phy_config) ==
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705) ||
+ (XGXS_EXT_PHY_TYPE(params->ext_phy_config) ==
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706) ||
+ (XGXS_EXT_PHY_TYPE(params->ext_phy_config) ==
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726))) {
+ vars->autoneg = AUTO_NEG_ENABLED;
+
+ if (gp_status & MDIO_AN_CL73_OR_37_COMPLETE) {
+ vars->autoneg |= AUTO_NEG_COMPLETE;
+ vars->link_status |=
+ LINK_STATUS_AUTO_NEGOTIATE_COMPLETE;
+ }
+
+ vars->autoneg |= AUTO_NEG_PARALLEL_DETECTION_USED;
+ vars->link_status |=
+ LINK_STATUS_PARALLEL_DETECTION_USED;
+
+ }
+ if (vars->flow_ctrl & BNX2X_FLOW_CTRL_TX)
+ vars->link_status |=
+ LINK_STATUS_TX_FLOW_CONTROL_ENABLED;
+
+ if (vars->flow_ctrl & BNX2X_FLOW_CTRL_RX)
+ vars->link_status |=
+ LINK_STATUS_RX_FLOW_CONTROL_ENABLED;
+
+ } else { /* link_down */
+ DP(NETIF_MSG_LINK, "phy link down\n");
+
+ vars->phy_link_up = 0;
+
+ vars->duplex = DUPLEX_FULL;
+ vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE;
+ vars->autoneg = AUTO_NEG_DISABLED;
+ vars->mac_type = MAC_TYPE_NONE;
+
+ if ((params->req_line_speed == SPEED_AUTO_NEG) &&
+ ((XGXS_EXT_PHY_TYPE(params->ext_phy_config) ==
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT))) {
+ /* Check signal is detected */
+ bnx2x_check_fallback_to_cl37(params);
+ }
+ }
+
+ DP(NETIF_MSG_LINK, "gp_status 0x%x phy_link_up %x line_speed %x\n",
+ gp_status, vars->phy_link_up, vars->line_speed);
+ DP(NETIF_MSG_LINK, "duplex %x flow_ctrl 0x%x"
+ " autoneg 0x%x\n",
+ vars->duplex,
+ vars->flow_ctrl, vars->autoneg);
+ DP(NETIF_MSG_LINK, "link_status 0x%x\n", vars->link_status);
+
+ return rc;
+}
+
+static void bnx2x_set_gmii_tx_driver(struct link_params *params)
+{
+ struct bnx2x *bp = params->bp;
+ u16 lp_up2;
+ u16 tx_driver;
+ u16 bank;
+
+ /* read precomp */
+ CL45_RD_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_OVER_1G,
+ MDIO_OVER_1G_LP_UP2, &lp_up2);
+
+ /* bits [10:7] at lp_up2, positioned at [15:12] */
+ lp_up2 = (((lp_up2 & MDIO_OVER_1G_LP_UP2_PREEMPHASIS_MASK) >>
+ MDIO_OVER_1G_LP_UP2_PREEMPHASIS_SHIFT) <<
+ MDIO_TX0_TX_DRIVER_PREEMPHASIS_SHIFT);
+
+ if (lp_up2 == 0)
+ return;
+
+ for (bank = MDIO_REG_BANK_TX0; bank <= MDIO_REG_BANK_TX3;
+ bank += (MDIO_REG_BANK_TX1 - MDIO_REG_BANK_TX0)) {
+ CL45_RD_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ bank,
+ MDIO_TX0_TX_DRIVER, &tx_driver);
+
+ /* replace tx_driver bits [15:12] */
+ if (lp_up2 !=
+ (tx_driver & MDIO_TX0_TX_DRIVER_PREEMPHASIS_MASK)) {
+ tx_driver &= ~MDIO_TX0_TX_DRIVER_PREEMPHASIS_MASK;
+ tx_driver |= lp_up2;
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ bank,
+ MDIO_TX0_TX_DRIVER, tx_driver);
+ }
+ }
+}
+
+static u8 bnx2x_emac_program(struct link_params *params,
+ u32 line_speed, u32 duplex)
+{
+ struct bnx2x *bp = params->bp;
+ u8 port = params->port;
+ u16 mode = 0;
+
+ DP(NETIF_MSG_LINK, "setting link speed & duplex\n");
+ bnx2x_bits_dis(bp, GRCBASE_EMAC0 + port*0x400 +
+ EMAC_REG_EMAC_MODE,
+ (EMAC_MODE_25G_MODE |
+ EMAC_MODE_PORT_MII_10M |
+ EMAC_MODE_HALF_DUPLEX));
+ switch (line_speed) {
+ case SPEED_10:
+ mode |= EMAC_MODE_PORT_MII_10M;
+ break;
+
+ case SPEED_100:
+ mode |= EMAC_MODE_PORT_MII;
+ break;
+
+ case SPEED_1000:
+ mode |= EMAC_MODE_PORT_GMII;
+ break;
+
+ case SPEED_2500:
+ mode |= (EMAC_MODE_25G_MODE | EMAC_MODE_PORT_GMII);
+ break;
+
+ default:
+ /* 10G not valid for EMAC */
+ DP(NETIF_MSG_LINK, "Invalid line_speed 0x%x\n", line_speed);
+ return -EINVAL;
+ }
+
+ if (duplex == DUPLEX_HALF)
+ mode |= EMAC_MODE_HALF_DUPLEX;
+ bnx2x_bits_en(bp,
+ GRCBASE_EMAC0 + port*0x400 + EMAC_REG_EMAC_MODE,
+ mode);
+
+ bnx2x_set_led(params, LED_MODE_OPER, line_speed);
+ return 0;
+}
+
+/*****************************************************************************/
+/* External Phy section */
+/*****************************************************************************/
+void bnx2x_ext_phy_hw_reset(struct bnx2x *bp, u8 port)
+{
+ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
+ MISC_REGISTERS_GPIO_OUTPUT_LOW, port);
+ msleep(1);
+ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
+ MISC_REGISTERS_GPIO_OUTPUT_HIGH, port);
+}
+
+static void bnx2x_ext_phy_reset(struct link_params *params,
+ struct link_vars *vars)
+{
+ struct bnx2x *bp = params->bp;
+ u32 ext_phy_type;
+ u8 ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config);
+
+ DP(NETIF_MSG_LINK, "Port %x: bnx2x_ext_phy_reset\n", params->port);
+ ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config);
+ /* The PHY reset is controled by GPIO 1
+ * Give it 1ms of reset pulse
+ */
+ if (vars->phy_flags & PHY_XGXS_FLAG) {
+
+ switch (ext_phy_type) {
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT:
+ DP(NETIF_MSG_LINK, "XGXS Direct\n");
+ break;
+
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705:
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706:
+ DP(NETIF_MSG_LINK, "XGXS 8705/8706\n");
+
+ /* Restore normal power mode*/
+ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
+ MISC_REGISTERS_GPIO_OUTPUT_HIGH,
+ params->port);
+
+ /* HW reset */
+ bnx2x_ext_phy_hw_reset(bp, params->port);
+
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_CTRL, 0xa040);
+ break;
+
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727:
+ break;
+
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726:
+
+ /* Restore normal power mode*/
+ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
+ MISC_REGISTERS_GPIO_OUTPUT_HIGH,
+ params->port);
+
+ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
+ MISC_REGISTERS_GPIO_OUTPUT_HIGH,
+ params->port);
+
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_CTRL,
+ 1<<15);
+ break;
+
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072:
+ DP(NETIF_MSG_LINK, "XGXS 8072\n");
+
+ /* Unset Low Power Mode and SW reset */
+ /* Restore normal power mode*/
+ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
+ MISC_REGISTERS_GPIO_OUTPUT_HIGH,
+ params->port);
+
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_CTRL,
+ 1<<15);
+ break;
+
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073:
+ DP(NETIF_MSG_LINK, "XGXS 8073\n");
+
+ /* Restore normal power mode*/
+ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
+ MISC_REGISTERS_GPIO_OUTPUT_HIGH,
+ params->port);
+
+ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
+ MISC_REGISTERS_GPIO_OUTPUT_HIGH,
+ params->port);
+ break;
+
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101:
+ DP(NETIF_MSG_LINK, "XGXS SFX7101\n");
+
+ /* Restore normal power mode*/
+ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
+ MISC_REGISTERS_GPIO_OUTPUT_HIGH,
+ params->port);
+
+ /* HW reset */
+ bnx2x_ext_phy_hw_reset(bp, params->port);
+ break;
+
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481:
+ /* Restore normal power mode*/
+ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
+ MISC_REGISTERS_GPIO_OUTPUT_HIGH,
+ params->port);
+
+ /* HW reset */
+ bnx2x_ext_phy_hw_reset(bp, params->port);
+
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_CTRL,
+ 1<<15);
+ break;
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823:
+ break;
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE:
+ DP(NETIF_MSG_LINK, "XGXS PHY Failure detected\n");
+ break;
+
+ default:
+ DP(NETIF_MSG_LINK, "BAD XGXS ext_phy_config 0x%x\n",
+ params->ext_phy_config);
+ break;
+ }
+
+ } else { /* SerDes */
+ ext_phy_type = SERDES_EXT_PHY_TYPE(params->ext_phy_config);
+ switch (ext_phy_type) {
+ case PORT_HW_CFG_SERDES_EXT_PHY_TYPE_DIRECT:
+ DP(NETIF_MSG_LINK, "SerDes Direct\n");
+ break;
+
+ case PORT_HW_CFG_SERDES_EXT_PHY_TYPE_BCM5482:
+ DP(NETIF_MSG_LINK, "SerDes 5482\n");
+ bnx2x_ext_phy_hw_reset(bp, params->port);
+ break;
+
+ default:
+ DP(NETIF_MSG_LINK, "BAD SerDes ext_phy_config 0x%x\n",
+ params->ext_phy_config);
+ break;
+ }
+ }
+}
+
+static void bnx2x_save_spirom_version(struct bnx2x *bp, u8 port,
+ u32 shmem_base, u32 spirom_ver)
+{
+ DP(NETIF_MSG_LINK, "FW version 0x%x:0x%x for port %d\n",
+ (u16)(spirom_ver>>16), (u16)spirom_ver, port);
+ REG_WR(bp, shmem_base +
+ offsetof(struct shmem_region,
+ port_mb[port].ext_phy_fw_version),
+ spirom_ver);
+}
+
+static void bnx2x_save_bcm_spirom_ver(struct bnx2x *bp, u8 port,
+ u32 ext_phy_type, u8 ext_phy_addr,
+ u32 shmem_base)
+{
+ u16 fw_ver1, fw_ver2;
+
+ bnx2x_cl45_read(bp, port, ext_phy_type, ext_phy_addr, MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_ROM_VER1, &fw_ver1);
+ bnx2x_cl45_read(bp, port, ext_phy_type, ext_phy_addr, MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_ROM_VER2, &fw_ver2);
+ bnx2x_save_spirom_version(bp, port, shmem_base,
+ (u32)(fw_ver1<<16 | fw_ver2));
+}
+
+
+static void bnx2x_save_8481_spirom_version(struct bnx2x *bp, u8 port,
+ u8 ext_phy_addr, u32 shmem_base)
+{
+ u16 val, fw_ver1, fw_ver2, cnt;
+ /* For the 32 bits registers in 8481, access via MDIO2ARM interface.*/
+ /* (1) set register 0xc200_0014(SPI_BRIDGE_CTRL_2) to 0x03000000 */
+ bnx2x_cl45_write(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481,
+ ext_phy_addr, MDIO_PMA_DEVAD,
+ 0xA819, 0x0014);
+ bnx2x_cl45_write(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ 0xA81A,
+ 0xc200);
+ bnx2x_cl45_write(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ 0xA81B,
+ 0x0000);
+ bnx2x_cl45_write(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ 0xA81C,
+ 0x0300);
+ bnx2x_cl45_write(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ 0xA817,
+ 0x0009);
+
+ for (cnt = 0; cnt < 100; cnt++) {
+ bnx2x_cl45_read(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ 0xA818,
+ &val);
+ if (val & 1)
+ break;
+ udelay(5);
+ }
+ if (cnt == 100) {
+ DP(NETIF_MSG_LINK, "Unable to read 8481 phy fw version(1)\n");
+ bnx2x_save_spirom_version(bp, port,
+ shmem_base, 0);
+ return;
+ }
+
+
+ /* 2) read register 0xc200_0000 (SPI_FW_STATUS) */
+ bnx2x_cl45_write(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481,
+ ext_phy_addr, MDIO_PMA_DEVAD,
+ 0xA819, 0x0000);
+ bnx2x_cl45_write(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481,
+ ext_phy_addr, MDIO_PMA_DEVAD,
+ 0xA81A, 0xc200);
+ bnx2x_cl45_write(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481,
+ ext_phy_addr, MDIO_PMA_DEVAD,
+ 0xA817, 0x000A);
+ for (cnt = 0; cnt < 100; cnt++) {
+ bnx2x_cl45_read(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ 0xA818,
+ &val);
+ if (val & 1)
+ break;
+ udelay(5);
+ }
+ if (cnt == 100) {
+ DP(NETIF_MSG_LINK, "Unable to read 8481 phy fw version(2)\n");
+ bnx2x_save_spirom_version(bp, port,
+ shmem_base, 0);
+ return;
+ }
+
+ /* lower 16 bits of the register SPI_FW_STATUS */
+ bnx2x_cl45_read(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ 0xA81B,
+ &fw_ver1);
+ /* upper 16 bits of register SPI_FW_STATUS */
+ bnx2x_cl45_read(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ 0xA81C,
+ &fw_ver2);
+
+ bnx2x_save_spirom_version(bp, port,
+ shmem_base, (fw_ver2<<16) | fw_ver1);
+}
+
+static void bnx2x_bcm8072_external_rom_boot(struct link_params *params)
+{
+ struct bnx2x *bp = params->bp;
+ u8 port = params->port;
+ u8 ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config);
+ u32 ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config);
+
+ /* Need to wait 200ms after reset */
+ msleep(200);
+ /* Boot port from external ROM
+ * Set ser_boot_ctl bit in the MISC_CTRL1 register
+ */
+ bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_MISC_CTRL1, 0x0001);
+
+ /* Reset internal microprocessor */
+ bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_GEN_CTRL,
+ MDIO_PMA_REG_GEN_CTRL_ROM_RESET_INTERNAL_MP);
+ /* set micro reset = 0 */
+ bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_GEN_CTRL,
+ MDIO_PMA_REG_GEN_CTRL_ROM_MICRO_RESET);
+ /* Reset internal microprocessor */
+ bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_GEN_CTRL,
+ MDIO_PMA_REG_GEN_CTRL_ROM_RESET_INTERNAL_MP);
+ /* wait for 100ms for code download via SPI port */
+ msleep(100);
+
+ /* Clear ser_boot_ctl bit */
+ bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_MISC_CTRL1, 0x0000);
+ /* Wait 100ms */
+ msleep(100);
+
+ bnx2x_save_bcm_spirom_ver(bp, port,
+ ext_phy_type,
+ ext_phy_addr,
+ params->shmem_base);
+}
+
+static u8 bnx2x_8073_is_snr_needed(struct link_params *params)
+{
+ /* This is only required for 8073A1, version 102 only */
+
+ struct bnx2x *bp = params->bp;
+ u8 ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config);
+ u16 val;
+
+ /* Read 8073 HW revision*/
+ bnx2x_cl45_read(bp, params->port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8073_CHIP_REV, &val);
+
+ if (val != 1) {
+ /* No need to workaround in 8073 A1 */
+ return 0;
+ }
+
+ bnx2x_cl45_read(bp, params->port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_ROM_VER2, &val);
+
+ /* SNR should be applied only for version 0x102 */
+ if (val != 0x102)
+ return 0;
+
+ return 1;
+}
+
+static u8 bnx2x_bcm8073_xaui_wa(struct link_params *params)
+{
+ struct bnx2x *bp = params->bp;
+ u8 ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config);
+ u16 val, cnt, cnt1 ;
+
+ bnx2x_cl45_read(bp, params->port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8073_CHIP_REV, &val);
+
+ if (val > 0) {
+ /* No need to workaround in 8073 A1 */
+ return 0;
+ }
+ /* XAUI workaround in 8073 A0: */
+
+ /* After loading the boot ROM and restarting Autoneg,
+ poll Dev1, Reg $C820: */
+
+ for (cnt = 0; cnt < 1000; cnt++) {
+ bnx2x_cl45_read(bp, params->port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8073_SPEED_LINK_STATUS,
+ &val);
+ /* If bit [14] = 0 or bit [13] = 0, continue on with
+ system initialization (XAUI work-around not required,
+ as these bits indicate 2.5G or 1G link up). */
+ if (!(val & (1<<14)) || !(val & (1<<13))) {
+ DP(NETIF_MSG_LINK, "XAUI work-around not required\n");
+ return 0;
+ } else if (!(val & (1<<15))) {
+ DP(NETIF_MSG_LINK, "clc bit 15 went off\n");
+ /* If bit 15 is 0, then poll Dev1, Reg $C841 until
+ it's MSB (bit 15) goes to 1 (indicating that the
+ XAUI workaround has completed),
+ then continue on with system initialization.*/
+ for (cnt1 = 0; cnt1 < 1000; cnt1++) {
+ bnx2x_cl45_read(bp, params->port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8073_XAUI_WA, &val);
+ if (val & (1<<15)) {
+ DP(NETIF_MSG_LINK,
+ "XAUI workaround has completed\n");
+ return 0;
+ }
+ msleep(3);
+ }
+ break;
+ }
+ msleep(3);
+ }
+ DP(NETIF_MSG_LINK, "Warning: XAUI work-around timeout !!!\n");
+ return -EINVAL;
+}
+
+static void bnx2x_bcm8073_bcm8727_external_rom_boot(struct bnx2x *bp, u8 port,
+ u8 ext_phy_addr,
+ u32 ext_phy_type,
+ u32 shmem_base)
+{
+ /* Boot port from external ROM */
+ /* EDC grst */
+ bnx2x_cl45_write(bp, port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_GEN_CTRL,
+ 0x0001);
+
+ /* ucode reboot and rst */
+ bnx2x_cl45_write(bp, port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_GEN_CTRL,
+ 0x008c);
+
+ bnx2x_cl45_write(bp, port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_MISC_CTRL1, 0x0001);
+
+ /* Reset internal microprocessor */
+ bnx2x_cl45_write(bp, port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_GEN_CTRL,
+ MDIO_PMA_REG_GEN_CTRL_ROM_MICRO_RESET);
+
+ /* Release srst bit */
+ bnx2x_cl45_write(bp, port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_GEN_CTRL,
+ MDIO_PMA_REG_GEN_CTRL_ROM_RESET_INTERNAL_MP);
+
+ /* wait for 100ms for code download via SPI port */
+ msleep(100);
+
+ /* Clear ser_boot_ctl bit */
+ bnx2x_cl45_write(bp, port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_MISC_CTRL1, 0x0000);
+
+ bnx2x_save_bcm_spirom_ver(bp, port,
+ ext_phy_type,
+ ext_phy_addr,
+ shmem_base);
+}
+
+static void bnx2x_bcm8073_external_rom_boot(struct bnx2x *bp, u8 port,
+ u8 ext_phy_addr,
+ u32 shmem_base)
+{
+ bnx2x_bcm8073_bcm8727_external_rom_boot(bp, port, ext_phy_addr,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073,
+ shmem_base);
+}
+
+static void bnx2x_bcm8727_external_rom_boot(struct bnx2x *bp, u8 port,
+ u8 ext_phy_addr,
+ u32 shmem_base)
+{
+ bnx2x_bcm8073_bcm8727_external_rom_boot(bp, port, ext_phy_addr,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727,
+ shmem_base);
+
+}
+
+static void bnx2x_bcm8726_external_rom_boot(struct link_params *params)
+{
+ struct bnx2x *bp = params->bp;
+ u8 port = params->port;
+ u8 ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config);
+ u32 ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config);
+
+ /* Need to wait 100ms after reset */
+ msleep(100);
+
+ /* Micro controller re-boot */
+ bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_GEN_CTRL,
+ 0x018B);
+
+ /* Set soft reset */
+ bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_GEN_CTRL,
+ MDIO_PMA_REG_GEN_CTRL_ROM_MICRO_RESET);
+
+ bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_MISC_CTRL1, 0x0001);
+
+ bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_GEN_CTRL,
+ MDIO_PMA_REG_GEN_CTRL_ROM_RESET_INTERNAL_MP);
+
+ /* wait for 150ms for microcode load */
+ msleep(150);
+
+ /* Disable serial boot control, tristates pins SS_N, SCK, MOSI, MISO */
+ bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_MISC_CTRL1, 0x0000);
+
+ msleep(200);
+ bnx2x_save_bcm_spirom_ver(bp, port,
+ ext_phy_type,
+ ext_phy_addr,
+ params->shmem_base);
+}
+
+static void bnx2x_sfp_set_transmitter(struct bnx2x *bp, u8 port,
+ u32 ext_phy_type, u8 ext_phy_addr,
+ u8 tx_en)
+{
+ u16 val;
+
+ DP(NETIF_MSG_LINK, "Setting transmitter tx_en=%x for port %x\n",
+ tx_en, port);
+ /* Disable/Enable transmitter ( TX laser of the SFP+ module.)*/
+ bnx2x_cl45_read(bp, port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_PHY_IDENTIFIER,
+ &val);
+
+ if (tx_en)
+ val &= ~(1<<15);
+ else
+ val |= (1<<15);
+
+ bnx2x_cl45_write(bp, port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_PHY_IDENTIFIER,
+ val);
+}
+
+static u8 bnx2x_8726_read_sfp_module_eeprom(struct link_params *params,
+ u16 addr, u8 byte_cnt, u8 *o_buf)
+{
+ struct bnx2x *bp = params->bp;
+ u16 val = 0;
+ u16 i;
+ u8 port = params->port;
+ u8 ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config);
+ u32 ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config);
+
+ if (byte_cnt > 16) {
+ DP(NETIF_MSG_LINK, "Reading from eeprom is"
+ " is limited to 0xf\n");
+ return -EINVAL;
+ }
+ /* Set the read command byte count */
+ bnx2x_cl45_write(bp, port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_SFP_TWO_WIRE_BYTE_CNT,
+ (byte_cnt | 0xa000));
+
+ /* Set the read command address */
+ bnx2x_cl45_write(bp, port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_SFP_TWO_WIRE_MEM_ADDR,
+ addr);
+
+ /* Activate read command */
+ bnx2x_cl45_write(bp, port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_SFP_TWO_WIRE_CTRL,
+ 0x2c0f);
+
+ /* Wait up to 500us for command complete status */
+ for (i = 0; i < 100; i++) {
+ bnx2x_cl45_read(bp, port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val);
+ if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) ==
+ MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_COMPLETE)
+ break;
+ udelay(5);
+ }
+
+ if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) !=
+ MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_COMPLETE) {
+ DP(NETIF_MSG_LINK,
+ "Got bad status 0x%x when reading from SFP+ EEPROM\n",
+ (val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK));
+ return -EINVAL;
+ }
+
+ /* Read the buffer */
+ for (i = 0; i < byte_cnt; i++) {
+ bnx2x_cl45_read(bp, port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8726_TWO_WIRE_DATA_BUF + i, &val);
+ o_buf[i] = (u8)(val & MDIO_PMA_REG_8726_TWO_WIRE_DATA_MASK);
+ }
+
+ for (i = 0; i < 100; i++) {
+ bnx2x_cl45_read(bp, port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val);
+ if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) ==
+ MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_IDLE)
+ return 0;;
+ msleep(1);
+ }
+ return -EINVAL;
+}
+
+static u8 bnx2x_8727_read_sfp_module_eeprom(struct link_params *params,
+ u16 addr, u8 byte_cnt, u8 *o_buf)
+{
+ struct bnx2x *bp = params->bp;
+ u16 val, i;
+ u8 port = params->port;
+ u8 ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config);
+ u32 ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config);
+
+ if (byte_cnt > 16) {
+ DP(NETIF_MSG_LINK, "Reading from eeprom is"
+ " is limited to 0xf\n");
+ return -EINVAL;
+ }
+
+ /* Need to read from 1.8000 to clear it */
+ bnx2x_cl45_read(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_SFP_TWO_WIRE_CTRL,
+ &val);
+
+ /* Set the read command byte count */
+ bnx2x_cl45_write(bp, port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_SFP_TWO_WIRE_BYTE_CNT,
+ ((byte_cnt < 2) ? 2 : byte_cnt));
+
+ /* Set the read command address */
+ bnx2x_cl45_write(bp, port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_SFP_TWO_WIRE_MEM_ADDR,
+ addr);
+ /* Set the destination address */
+ bnx2x_cl45_write(bp, port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ 0x8004,
+ MDIO_PMA_REG_8727_TWO_WIRE_DATA_BUF);
+
+ /* Activate read command */
+ bnx2x_cl45_write(bp, port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_SFP_TWO_WIRE_CTRL,
+ 0x8002);
+ /* Wait appropriate time for two-wire command to finish before
+ polling the status register */
+ msleep(1);
+
+ /* Wait up to 500us for command complete status */
+ for (i = 0; i < 100; i++) {
+ bnx2x_cl45_read(bp, port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val);
+ if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) ==
+ MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_COMPLETE)
+ break;
+ udelay(5);
+ }
+
+ if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) !=
+ MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_COMPLETE) {
+ DP(NETIF_MSG_LINK,
+ "Got bad status 0x%x when reading from SFP+ EEPROM\n",
+ (val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK));
+ return -EINVAL;
+ }
+
+ /* Read the buffer */
+ for (i = 0; i < byte_cnt; i++) {
+ bnx2x_cl45_read(bp, port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8727_TWO_WIRE_DATA_BUF + i, &val);
+ o_buf[i] = (u8)(val & MDIO_PMA_REG_8727_TWO_WIRE_DATA_MASK);
+ }
+
+ for (i = 0; i < 100; i++) {
+ bnx2x_cl45_read(bp, port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val);
+ if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) ==
+ MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_IDLE)
+ return 0;;
+ msleep(1);
+ }
+
+ return -EINVAL;
+}
+
+u8 bnx2x_read_sfp_module_eeprom(struct link_params *params, u16 addr,
+ u8 byte_cnt, u8 *o_buf)
+{
+ u32 ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config);
+
+ if (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726)
+ return bnx2x_8726_read_sfp_module_eeprom(params, addr,
+ byte_cnt, o_buf);
+ else if (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727)
+ return bnx2x_8727_read_sfp_module_eeprom(params, addr,
+ byte_cnt, o_buf);
+ return -EINVAL;
+}
+
+static u8 bnx2x_get_edc_mode(struct link_params *params,
+ u16 *edc_mode)
+{
+ struct bnx2x *bp = params->bp;
+ u8 val, check_limiting_mode = 0;
+ *edc_mode = EDC_MODE_LIMITING;
+
+ /* First check for copper cable */
+ if (bnx2x_read_sfp_module_eeprom(params,
+ SFP_EEPROM_CON_TYPE_ADDR,
+ 1,
+ &val) != 0) {
+ DP(NETIF_MSG_LINK, "Failed to read from SFP+ module EEPROM\n");
+ return -EINVAL;
+ }
+
+ switch (val) {
+ case SFP_EEPROM_CON_TYPE_VAL_COPPER:
+ {
+ u8 copper_module_type;
+
+ /* Check if its active cable( includes SFP+ module)
+ of passive cable*/
+ if (bnx2x_read_sfp_module_eeprom(params,
+ SFP_EEPROM_FC_TX_TECH_ADDR,
+ 1,
+ &copper_module_type) !=
+ 0) {
+ DP(NETIF_MSG_LINK,
+ "Failed to read copper-cable-type"
+ " from SFP+ EEPROM\n");
+ return -EINVAL;
+ }
+
+ if (copper_module_type &
+ SFP_EEPROM_FC_TX_TECH_BITMASK_COPPER_ACTIVE) {
+ DP(NETIF_MSG_LINK, "Active Copper cable detected\n");
+ check_limiting_mode = 1;
+ } else if (copper_module_type &
+ SFP_EEPROM_FC_TX_TECH_BITMASK_COPPER_PASSIVE) {
+ DP(NETIF_MSG_LINK, "Passive Copper"
+ " cable detected\n");
+ *edc_mode =
+ EDC_MODE_PASSIVE_DAC;
+ } else {
+ DP(NETIF_MSG_LINK, "Unknown copper-cable-"
+ "type 0x%x !!!\n", copper_module_type);
+ return -EINVAL;
+ }
+ break;
+ }
+ case SFP_EEPROM_CON_TYPE_VAL_LC:
+ DP(NETIF_MSG_LINK, "Optic module detected\n");
+ check_limiting_mode = 1;
+ break;
+ default:
+ DP(NETIF_MSG_LINK, "Unable to determine module type 0x%x !!!\n",
+ val);
+ return -EINVAL;
+ }
+
+ if (check_limiting_mode) {
+ u8 options[SFP_EEPROM_OPTIONS_SIZE];
+ if (bnx2x_read_sfp_module_eeprom(params,
+ SFP_EEPROM_OPTIONS_ADDR,
+ SFP_EEPROM_OPTIONS_SIZE,
+ options) != 0) {
+ DP(NETIF_MSG_LINK, "Failed to read Option"
+ " field from module EEPROM\n");
+ return -EINVAL;
+ }
+ if ((options[0] & SFP_EEPROM_OPTIONS_LINEAR_RX_OUT_MASK))
+ *edc_mode = EDC_MODE_LINEAR;
+ else
+ *edc_mode = EDC_MODE_LIMITING;
+ }
+ DP(NETIF_MSG_LINK, "EDC mode is set to 0x%x\n", *edc_mode);
+ return 0;
+}
+
+/* This function read the relevant field from the module ( SFP+ ),
+ and verify it is compliant with this board */
+static u8 bnx2x_verify_sfp_module(struct link_params *params)
+{
+ struct bnx2x *bp = params->bp;
+ u32 val;
+ u32 fw_resp;
+ char vendor_name[SFP_EEPROM_VENDOR_NAME_SIZE+1];
+ char vendor_pn[SFP_EEPROM_PART_NO_SIZE+1];
+
+ val = REG_RD(bp, params->shmem_base +
+ offsetof(struct shmem_region, dev_info.
+ port_feature_config[params->port].config));
+ if ((val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) ==
+ PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_NO_ENFORCEMENT) {
+ DP(NETIF_MSG_LINK, "NOT enforcing module verification\n");
+ return 0;
+ }
+
+ /* Ask the FW to validate the module */
+ if (!(params->feature_config_flags &
+ FEATURE_CONFIG_BC_SUPPORTS_OPT_MDL_VRFY)) {
+ DP(NETIF_MSG_LINK, "FW does not support OPT MDL "
+ "verification\n");
+ return -EINVAL;
+ }
+
+ fw_resp = bnx2x_fw_command(bp, DRV_MSG_CODE_VRFY_OPT_MDL);
+ if (fw_resp == FW_MSG_CODE_VRFY_OPT_MDL_SUCCESS) {
+ DP(NETIF_MSG_LINK, "Approved module\n");
+ return 0;
+ }
+
+ /* format the warning message */
+ if (bnx2x_read_sfp_module_eeprom(params,
+ SFP_EEPROM_VENDOR_NAME_ADDR,
+ SFP_EEPROM_VENDOR_NAME_SIZE,
+ (u8 *)vendor_name))
+ vendor_name[0] = '\0';
+ else
+ vendor_name[SFP_EEPROM_VENDOR_NAME_SIZE] = '\0';
+ if (bnx2x_read_sfp_module_eeprom(params,
+ SFP_EEPROM_PART_NO_ADDR,
+ SFP_EEPROM_PART_NO_SIZE,
+ (u8 *)vendor_pn))
+ vendor_pn[0] = '\0';
+ else
+ vendor_pn[SFP_EEPROM_PART_NO_SIZE] = '\0';
+
+ netdev_info(bp->dev, "Warning: Unqualified SFP+ module detected, Port %d from %s part number %s\n",
+ params->port, vendor_name, vendor_pn);
+ return -EINVAL;
+}
+
+static u8 bnx2x_bcm8726_set_limiting_mode(struct link_params *params,
+ u16 edc_mode)
+{
+ struct bnx2x *bp = params->bp;
+ u8 port = params->port;
+ u8 ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config);
+ u16 cur_limiting_mode;
+
+ bnx2x_cl45_read(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_ROM_VER2,
+ &cur_limiting_mode);
+ DP(NETIF_MSG_LINK, "Current Limiting mode is 0x%x\n",
+ cur_limiting_mode);
+
+ if (edc_mode == EDC_MODE_LIMITING) {
+ DP(NETIF_MSG_LINK,
+ "Setting LIMITING MODE\n");
+ bnx2x_cl45_write(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_ROM_VER2,
+ EDC_MODE_LIMITING);
+ } else { /* LRM mode ( default )*/
+
+ DP(NETIF_MSG_LINK, "Setting LRM MODE\n");
+
+ /* Changing to LRM mode takes quite few seconds.
+ So do it only if current mode is limiting
+ ( default is LRM )*/
+ if (cur_limiting_mode != EDC_MODE_LIMITING)
+ return 0;
+
+ bnx2x_cl45_write(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_LRM_MODE,
+ 0);
+ bnx2x_cl45_write(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_ROM_VER2,
+ 0x128);
+ bnx2x_cl45_write(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_MISC_CTRL0,
+ 0x4008);
+ bnx2x_cl45_write(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_LRM_MODE,
+ 0xaaaa);
+ }
+ return 0;
+}
+
+static u8 bnx2x_bcm8727_set_limiting_mode(struct link_params *params,
+ u16 edc_mode)
+{
+ struct bnx2x *bp = params->bp;
+ u8 port = params->port;
+ u16 phy_identifier;
+ u16 rom_ver2_val;
+ u8 ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config);
+
+ bnx2x_cl45_read(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_PHY_IDENTIFIER,
+ &phy_identifier);
+
+ bnx2x_cl45_write(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_PHY_IDENTIFIER,
+ (phy_identifier & ~(1<<9)));
+
+ bnx2x_cl45_read(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_ROM_VER2,
+ &rom_ver2_val);
+ /* Keep the MSB 8-bits, and set the LSB 8-bits with the edc_mode */
+ bnx2x_cl45_write(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_ROM_VER2,
+ (rom_ver2_val & 0xff00) | (edc_mode & 0x00ff));
+
+ bnx2x_cl45_write(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_PHY_IDENTIFIER,
+ (phy_identifier | (1<<9)));
+
+ return 0;
+}
+
+
+static u8 bnx2x_wait_for_sfp_module_initialized(struct link_params *params)
+{
+ u8 val;
+ struct bnx2x *bp = params->bp;
+ u16 timeout;
+ /* Initialization time after hot-plug may take up to 300ms for some
+ phys type ( e.g. JDSU ) */
+ for (timeout = 0; timeout < 60; timeout++) {
+ if (bnx2x_read_sfp_module_eeprom(params, 1, 1, &val)
+ == 0) {
+ DP(NETIF_MSG_LINK, "SFP+ module initialization "
+ "took %d ms\n", timeout * 5);
+ return 0;
+ }
+ msleep(5);
+ }
+ return -EINVAL;
+}
+
+static void bnx2x_8727_power_module(struct bnx2x *bp,
+ struct link_params *params,
+ u8 ext_phy_addr, u8 is_power_up) {
+ /* Make sure GPIOs are not using for LED mode */
+ u16 val;
+ u8 port = params->port;
+ /*
+ * In the GPIO register, bit 4 is use to detemine if the GPIOs are
+ * operating as INPUT or as OUTPUT. Bit 1 is for input, and 0 for
+ * output
+ * Bits 0-1 determine the gpios value for OUTPUT in case bit 4 val is 0
+ * Bits 8-9 determine the gpios value for INPUT in case bit 4 val is 1
+ * where the 1st bit is the over-current(only input), and 2nd bit is
+ * for power( only output )
+ */
+
+ /*
+ * In case of NOC feature is disabled and power is up, set GPIO control
+ * as input to enable listening of over-current indication
+ */
+
+ if (!(params->feature_config_flags &
+ FEATURE_CONFIG_BCM8727_NOC) && is_power_up)
+ val = (1<<4);
+ else
+ /*
+ * Set GPIO control to OUTPUT, and set the power bit
+ * to according to the is_power_up
+ */
+ val = ((!(is_power_up)) << 1);
+
+ bnx2x_cl45_write(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8727_GPIO_CTRL,
+ val);
+}
+
+static u8 bnx2x_sfp_module_detection(struct link_params *params)
+{
+ struct bnx2x *bp = params->bp;
+ u16 edc_mode;
+ u8 rc = 0;
+ u8 ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config);
+ u32 ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config);
+ u32 val = REG_RD(bp, params->shmem_base +
+ offsetof(struct shmem_region, dev_info.
+ port_feature_config[params->port].config));
+
+ DP(NETIF_MSG_LINK, "SFP+ module plugged in/out detected on port %d\n",
+ params->port);
+
+ if (bnx2x_get_edc_mode(params, &edc_mode) != 0) {
+ DP(NETIF_MSG_LINK, "Failed to get valid module type\n");
+ return -EINVAL;
+ } else if (bnx2x_verify_sfp_module(params) !=
+ 0) {
+ /* check SFP+ module compatibility */
+ DP(NETIF_MSG_LINK, "Module verification failed!!\n");
+ rc = -EINVAL;
+ /* Turn on fault module-detected led */
+ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_0,
+ MISC_REGISTERS_GPIO_HIGH,
+ params->port);
+ if ((ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727) &&
+ ((val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) ==
+ PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_POWER_DOWN)) {
+ /* Shutdown SFP+ module */
+ DP(NETIF_MSG_LINK, "Shutdown SFP+ module!!\n");
+ bnx2x_8727_power_module(bp, params,
+ ext_phy_addr, 0);
+ return rc;
+ }
+ } else {
+ /* Turn off fault module-detected led */
+ DP(NETIF_MSG_LINK, "Turn off fault module-detected led\n");
+ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_0,
+ MISC_REGISTERS_GPIO_LOW,
+ params->port);
+ }
+
+ /* power up the SFP module */
+ if (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727)
+ bnx2x_8727_power_module(bp, params, ext_phy_addr, 1);
+
+ /* Check and set limiting mode / LRM mode on 8726.
+ On 8727 it is done automatically */
+ if (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726)
+ bnx2x_bcm8726_set_limiting_mode(params, edc_mode);
+ else
+ bnx2x_bcm8727_set_limiting_mode(params, edc_mode);
+ /*
+ * Enable transmit for this module if the module is approved, or
+ * if unapproved modules should also enable the Tx laser
+ */
+ if (rc == 0 ||
+ (val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) !=
+ PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_DISABLE_TX_LASER)
+ bnx2x_sfp_set_transmitter(bp, params->port,
+ ext_phy_type, ext_phy_addr, 1);
+ else
+ bnx2x_sfp_set_transmitter(bp, params->port,
+ ext_phy_type, ext_phy_addr, 0);
+
+ return rc;
+}
+
+void bnx2x_handle_module_detect_int(struct link_params *params)
+{
+ struct bnx2x *bp = params->bp;
+ u32 gpio_val;
+ u8 port = params->port;
+
+ /* Set valid module led off */
+ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_0,
+ MISC_REGISTERS_GPIO_HIGH,
+ params->port);
+
+ /* Get current gpio val refelecting module plugged in / out*/
+ gpio_val = bnx2x_get_gpio(bp, MISC_REGISTERS_GPIO_3, port);
+
+ /* Call the handling function in case module is detected */
+ if (gpio_val == 0) {
+
+ bnx2x_set_gpio_int(bp, MISC_REGISTERS_GPIO_3,
+ MISC_REGISTERS_GPIO_INT_OUTPUT_CLR,
+ port);
+
+ if (bnx2x_wait_for_sfp_module_initialized(params) ==
+ 0)
+ bnx2x_sfp_module_detection(params);
+ else
+ DP(NETIF_MSG_LINK, "SFP+ module is not initialized\n");
+ } else {
+ u8 ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config);
+
+ u32 ext_phy_type =
+ XGXS_EXT_PHY_TYPE(params->ext_phy_config);
+ u32 val = REG_RD(bp, params->shmem_base +
+ offsetof(struct shmem_region, dev_info.
+ port_feature_config[params->port].
+ config));
+
+ bnx2x_set_gpio_int(bp, MISC_REGISTERS_GPIO_3,
+ MISC_REGISTERS_GPIO_INT_OUTPUT_SET,
+ port);
+ /* Module was plugged out. */
+ /* Disable transmit for this module */
+ if ((val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) ==
+ PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_DISABLE_TX_LASER)
+ bnx2x_sfp_set_transmitter(bp, params->port,
+ ext_phy_type, ext_phy_addr, 0);
+ }
+}
+
+static void bnx2x_bcm807x_force_10G(struct link_params *params)
+{
+ struct bnx2x *bp = params->bp;
+ u8 port = params->port;
+ u8 ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config);
+ u32 ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config);
+
+ /* Force KR or KX */
+ bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_CTRL,
+ 0x2040);
+ bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_10G_CTRL2,
+ 0x000b);
+ bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_BCM_CTRL,
+ 0x0000);
+ bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_CTRL,
+ 0x0000);
+}
+
+static void bnx2x_bcm8073_set_xaui_low_power_mode(struct link_params *params)
+{
+ struct bnx2x *bp = params->bp;
+ u8 port = params->port;
+ u16 val;
+ u8 ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config);
+ u32 ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config);
+
+ bnx2x_cl45_read(bp, params->port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8073_CHIP_REV, &val);
+
+ if (val == 0) {
+ /* Mustn't set low power mode in 8073 A0 */
+ return;
+ }
+
+ /* Disable PLL sequencer (use read-modify-write to clear bit 13) */
+ bnx2x_cl45_read(bp, port, ext_phy_type, ext_phy_addr,
+ MDIO_XS_DEVAD,
+ MDIO_XS_PLL_SEQUENCER, &val);
+ val &= ~(1<<13);
+ bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr,
+ MDIO_XS_DEVAD, MDIO_XS_PLL_SEQUENCER, val);
+
+ /* PLL controls */
+ bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr,
+ MDIO_XS_DEVAD, 0x805E, 0x1077);
+ bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr,
+ MDIO_XS_DEVAD, 0x805D, 0x0000);
+ bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr,
+ MDIO_XS_DEVAD, 0x805C, 0x030B);
+ bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr,
+ MDIO_XS_DEVAD, 0x805B, 0x1240);
+ bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr,
+ MDIO_XS_DEVAD, 0x805A, 0x2490);
+
+ /* Tx Controls */
+ bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr,
+ MDIO_XS_DEVAD, 0x80A7, 0x0C74);
+ bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr,
+ MDIO_XS_DEVAD, 0x80A6, 0x9041);
+ bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr,
+ MDIO_XS_DEVAD, 0x80A5, 0x4640);
+
+ /* Rx Controls */
+ bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr,
+ MDIO_XS_DEVAD, 0x80FE, 0x01C4);
+ bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr,
+ MDIO_XS_DEVAD, 0x80FD, 0x9249);
+ bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr,
+ MDIO_XS_DEVAD, 0x80FC, 0x2015);
+
+ /* Enable PLL sequencer (use read-modify-write to set bit 13) */
+ bnx2x_cl45_read(bp, port, ext_phy_type, ext_phy_addr,
+ MDIO_XS_DEVAD,
+ MDIO_XS_PLL_SEQUENCER, &val);
+ val |= (1<<13);
+ bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr,
+ MDIO_XS_DEVAD, MDIO_XS_PLL_SEQUENCER, val);
+}
+
+static void bnx2x_8073_set_pause_cl37(struct link_params *params,
+ struct link_vars *vars)
+{
+ struct bnx2x *bp = params->bp;
+ u16 cl37_val;
+ u8 ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config);
+ u32 ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config);
+
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_CL37_FC_LD, &cl37_val);
+
+ cl37_val &= ~MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH;
+ /* Please refer to Table 28B-3 of 802.3ab-1999 spec. */
+
+ if ((vars->ieee_fc &
+ MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_SYMMETRIC) ==
+ MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_SYMMETRIC) {
+ cl37_val |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_SYMMETRIC;
+ }
+ if ((vars->ieee_fc &
+ MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) ==
+ MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) {
+ cl37_val |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC;
+ }
+ if ((vars->ieee_fc &
+ MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) ==
+ MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) {
+ cl37_val |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH;
+ }
+ DP(NETIF_MSG_LINK,
+ "Ext phy AN advertize cl37 0x%x\n", cl37_val);
+
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_CL37_FC_LD, cl37_val);
+ msleep(500);
+}
+
+static void bnx2x_ext_phy_set_pause(struct link_params *params,
+ struct link_vars *vars)
+{
+ struct bnx2x *bp = params->bp;
+ u16 val;
+ u8 ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config);
+ u32 ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config);
+
+ /* read modify write pause advertizing */
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_ADV_PAUSE, &val);
+
+ val &= ~MDIO_AN_REG_ADV_PAUSE_BOTH;
+
+ /* Please refer to Table 28B-3 of 802.3ab-1999 spec. */
+
+ if ((vars->ieee_fc &
+ MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) ==
+ MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) {
+ val |= MDIO_AN_REG_ADV_PAUSE_ASYMMETRIC;
+ }
+ if ((vars->ieee_fc &
+ MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) ==
+ MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) {
+ val |=
+ MDIO_AN_REG_ADV_PAUSE_PAUSE;
+ }
+ DP(NETIF_MSG_LINK,
+ "Ext phy AN advertize 0x%x\n", val);
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_ADV_PAUSE, val);
+}
+static void bnx2x_set_preemphasis(struct link_params *params)
+{
+ u16 bank, i = 0;
+ struct bnx2x *bp = params->bp;
+
+ for (bank = MDIO_REG_BANK_RX0, i = 0; bank <= MDIO_REG_BANK_RX3;
+ bank += (MDIO_REG_BANK_RX1-MDIO_REG_BANK_RX0), i++) {
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ bank,
+ MDIO_RX0_RX_EQ_BOOST,
+ params->xgxs_config_rx[i]);
+ }
+
+ for (bank = MDIO_REG_BANK_TX0, i = 0; bank <= MDIO_REG_BANK_TX3;
+ bank += (MDIO_REG_BANK_TX1 - MDIO_REG_BANK_TX0), i++) {
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ bank,
+ MDIO_TX0_TX_DRIVER,
+ params->xgxs_config_tx[i]);
+ }
+}
+
+
+static void bnx2x_8481_set_led4(struct link_params *params,
+ u32 ext_phy_type, u8 ext_phy_addr)
+{
+ struct bnx2x *bp = params->bp;
+
+ /* PHYC_CTL_LED_CTL */
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8481_LINK_SIGNAL, 0xa482);
+
+ /* Unmask LED4 for 10G link */
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8481_SIGNAL_MASK, (1<<6));
+ /* 'Interrupt Mask' */
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ 0xFFFB, 0xFFFD);
+}
+static void bnx2x_8481_set_legacy_led_mode(struct link_params *params,
+ u32 ext_phy_type, u8 ext_phy_addr)
+{
+ struct bnx2x *bp = params->bp;
+
+ /* LED1 (10G Link): Disable LED1 when 10/100/1000 link */
+ /* LED2 (1G/100/10 Link): Enable LED2 when 10/100/1000 link) */
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_8481_LEGACY_SHADOW,
+ (1<<15) | (0xd << 10) | (0xc<<4) | 0xe);
+}
+
+static void bnx2x_8481_set_10G_led_mode(struct link_params *params,
+ u32 ext_phy_type, u8 ext_phy_addr)
+{
+ struct bnx2x *bp = params->bp;
+ u16 val1;
+
+ /* LED1 (10G Link) */
+ /* Enable continuse based on source 7(10G-link) */
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8481_LINK_SIGNAL,
+ &val1);
+ /* Set bit 2 to 0, and bits [1:0] to 10 */
+ val1 &= ~((1<<0) | (1<<2) | (1<<7)); /* Clear bits 0,2,7*/
+ val1 |= ((1<<1) | (1<<6)); /* Set bit 1, 6 */
+
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8481_LINK_SIGNAL,
+ val1);
+
+ /* Unmask LED1 for 10G link */
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8481_LED1_MASK,
+ &val1);
+ /* Set bit 2 to 0, and bits [1:0] to 10 */
+ val1 |= (1<<7);
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8481_LED1_MASK,
+ val1);
+
+ /* LED2 (1G/100/10G Link) */
+ /* Mask LED2 for 10G link */
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8481_LED2_MASK,
+ 0);
+
+ /* Unmask LED3 for 10G link */
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8481_LED3_MASK,
+ 0x6);
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8481_LED3_BLINK,
+ 0);
+}
+
+
+static void bnx2x_init_internal_phy(struct link_params *params,
+ struct link_vars *vars,
+ u8 enable_cl73)
+{
+ struct bnx2x *bp = params->bp;
+
+ if (!(vars->phy_flags & PHY_SGMII_FLAG)) {
+ if ((XGXS_EXT_PHY_TYPE(params->ext_phy_config) ==
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) &&
+ (params->feature_config_flags &
+ FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED))
+ bnx2x_set_preemphasis(params);
+
+ /* forced speed requested? */
+ if (vars->line_speed != SPEED_AUTO_NEG ||
+ ((XGXS_EXT_PHY_TYPE(params->ext_phy_config) ==
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) &&
+ params->loopback_mode == LOOPBACK_EXT)) {
+ DP(NETIF_MSG_LINK, "not SGMII, no AN\n");
+
+ /* disable autoneg */
+ bnx2x_set_autoneg(params, vars, 0);
+
+ /* program speed and duplex */
+ bnx2x_program_serdes(params, vars);
+
+ } else { /* AN_mode */
+ DP(NETIF_MSG_LINK, "not SGMII, AN\n");
+
+ /* AN enabled */
+ bnx2x_set_brcm_cl37_advertisment(params);
+
+ /* program duplex & pause advertisement (for aneg) */
+ bnx2x_set_ieee_aneg_advertisment(params,
+ vars->ieee_fc);
+
+ /* enable autoneg */
+ bnx2x_set_autoneg(params, vars, enable_cl73);
+
+ /* enable and restart AN */
+ bnx2x_restart_autoneg(params, enable_cl73);
+ }
+
+ } else { /* SGMII mode */
+ DP(NETIF_MSG_LINK, "SGMII\n");
+
+ bnx2x_initialize_sgmii_process(params, vars);
+ }
+}
+
+static u8 bnx2x_ext_phy_init(struct link_params *params, struct link_vars *vars)
+{
+ struct bnx2x *bp = params->bp;
+ u32 ext_phy_type;
+ u8 ext_phy_addr;
+ u16 cnt;
+ u16 ctrl = 0;
+ u16 val = 0;
+ u8 rc = 0;
+
+ if (vars->phy_flags & PHY_XGXS_FLAG) {
+ ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config);
+
+ ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config);
+ /* Make sure that the soft reset is off (expect for the 8072:
+ * due to the lock, it will be done inside the specific
+ * handling)
+ */
+ if ((ext_phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) &&
+ (ext_phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE) &&
+ (ext_phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_NOT_CONN) &&
+ (ext_phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072) &&
+ (ext_phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073)) {
+ /* Wait for soft reset to get cleared upto 1 sec */
+ for (cnt = 0; cnt < 1000; cnt++) {
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_CTRL, &ctrl);
+ if (!(ctrl & (1<<15)))
+ break;
+ msleep(1);
+ }
+ DP(NETIF_MSG_LINK, "control reg 0x%x (after %d ms)\n",
+ ctrl, cnt);
+ }
+
+ switch (ext_phy_type) {
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT:
+ break;
+
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705:
+ DP(NETIF_MSG_LINK, "XGXS 8705\n");
+
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_MISC_CTRL,
+ 0x8288);
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_PHY_IDENTIFIER,
+ 0x7fbf);
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_CMU_PLL_BYPASS,
+ 0x0100);
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_WIS_DEVAD,
+ MDIO_WIS_REG_LASI_CNTL, 0x1);
+
+ /* BCM8705 doesn't have microcode, hence the 0 */
+ bnx2x_save_spirom_version(bp, params->port,
+ params->shmem_base, 0);
+ break;
+
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706:
+ /* Wait until fw is loaded */
+ for (cnt = 0; cnt < 100; cnt++) {
+ bnx2x_cl45_read(bp, params->port, ext_phy_type,
+ ext_phy_addr, MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_ROM_VER1, &val);
+ if (val)
+ break;
+ msleep(10);
+ }
+ DP(NETIF_MSG_LINK, "XGXS 8706 is initialized "
+ "after %d ms\n", cnt);
+ if ((params->feature_config_flags &
+ FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED)) {
+ u8 i;
+ u16 reg;
+ for (i = 0; i < 4; i++) {
+ reg = MDIO_XS_8706_REG_BANK_RX0 +
+ i*(MDIO_XS_8706_REG_BANK_RX1 -
+ MDIO_XS_8706_REG_BANK_RX0);
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_XS_DEVAD,
+ reg, &val);
+ /* Clear first 3 bits of the control */
+ val &= ~0x7;
+ /* Set control bits according to
+ configuation */
+ val |= (params->xgxs_config_rx[i] &
+ 0x7);
+ DP(NETIF_MSG_LINK, "Setting RX"
+ "Equalizer to BCM8706 reg 0x%x"
+ " <-- val 0x%x\n", reg, val);
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_XS_DEVAD,
+ reg, val);
+ }
+ }
+ /* Force speed */
+ if (params->req_line_speed == SPEED_10000) {
+ DP(NETIF_MSG_LINK, "XGXS 8706 force 10Gbps\n");
+
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_DIGITAL_CTRL,
+ 0x400);
+ bnx2x_cl45_write(bp, params->port, ext_phy_type,
+ ext_phy_addr, MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_LASI_CTRL, 1);
+ } else {
+ /* Force 1Gbps using autoneg with 1G
+ advertisment */
+
+ /* Allow CL37 through CL73 */
+ DP(NETIF_MSG_LINK, "XGXS 8706 AutoNeg\n");
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_CL37_CL73,
+ 0x040c);
+
+ /* Enable Full-Duplex advertisment on CL37 */
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_CL37_FC_LP,
+ 0x0020);
+ /* Enable CL37 AN */
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_CL37_AN,
+ 0x1000);
+ /* 1G support */
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_ADV, (1<<5));
+
+ /* Enable clause 73 AN */
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_CTRL,
+ 0x1200);
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_RX_ALARM_CTRL,
+ 0x0400);
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_LASI_CTRL, 0x0004);
+
+ }
+ bnx2x_save_bcm_spirom_ver(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ params->shmem_base);
+ break;
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726:
+ DP(NETIF_MSG_LINK, "Initializing BCM8726\n");
+ bnx2x_bcm8726_external_rom_boot(params);
+
+ /* Need to call module detected on initialization since
+ the module detection triggered by actual module
+ insertion might occur before driver is loaded, and when
+ driver is loaded, it reset all registers, including the
+ transmitter */
+ bnx2x_sfp_module_detection(params);
+
+ /* Set Flow control */
+ bnx2x_ext_phy_set_pause(params, vars);
+ if (params->req_line_speed == SPEED_1000) {
+ DP(NETIF_MSG_LINK, "Setting 1G force\n");
+ bnx2x_cl45_write(bp, params->port, ext_phy_type,
+ ext_phy_addr, MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_CTRL, 0x40);
+ bnx2x_cl45_write(bp, params->port, ext_phy_type,
+ ext_phy_addr, MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_10G_CTRL2, 0xD);
+ bnx2x_cl45_write(bp, params->port, ext_phy_type,
+ ext_phy_addr, MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_LASI_CTRL, 0x5);
+ bnx2x_cl45_write(bp, params->port, ext_phy_type,
+ ext_phy_addr, MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_RX_ALARM_CTRL,
+ 0x400);
+ } else if ((params->req_line_speed ==
+ SPEED_AUTO_NEG) &&
+ ((params->speed_cap_mask &
+ PORT_HW_CFG_SPEED_CAPABILITY_D0_1G))) {
+ DP(NETIF_MSG_LINK, "Setting 1G clause37\n");
+ bnx2x_cl45_write(bp, params->port, ext_phy_type,
+ ext_phy_addr, MDIO_AN_DEVAD,
+ MDIO_AN_REG_ADV, 0x20);
+ bnx2x_cl45_write(bp, params->port, ext_phy_type,
+ ext_phy_addr, MDIO_AN_DEVAD,
+ MDIO_AN_REG_CL37_CL73, 0x040c);
+ bnx2x_cl45_write(bp, params->port, ext_phy_type,
+ ext_phy_addr, MDIO_AN_DEVAD,
+ MDIO_AN_REG_CL37_FC_LD, 0x0020);
+ bnx2x_cl45_write(bp, params->port, ext_phy_type,
+ ext_phy_addr, MDIO_AN_DEVAD,
+ MDIO_AN_REG_CL37_AN, 0x1000);
+ bnx2x_cl45_write(bp, params->port, ext_phy_type,
+ ext_phy_addr, MDIO_AN_DEVAD,
+ MDIO_AN_REG_CTRL, 0x1200);
+
+ /* Enable RX-ALARM control to receive
+ interrupt for 1G speed change */
+ bnx2x_cl45_write(bp, params->port, ext_phy_type,
+ ext_phy_addr, MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_LASI_CTRL, 0x4);
+ bnx2x_cl45_write(bp, params->port, ext_phy_type,
+ ext_phy_addr, MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_RX_ALARM_CTRL,
+ 0x400);
+
+ } else { /* Default 10G. Set only LASI control */
+ bnx2x_cl45_write(bp, params->port, ext_phy_type,
+ ext_phy_addr, MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_LASI_CTRL, 1);
+ }
+
+ /* Set TX PreEmphasis if needed */
+ if ((params->feature_config_flags &
+ FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED)) {
+ DP(NETIF_MSG_LINK, "Setting TX_CTRL1 0x%x,"
+ "TX_CTRL2 0x%x\n",
+ params->xgxs_config_tx[0],
+ params->xgxs_config_tx[1]);
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8726_TX_CTRL1,
+ params->xgxs_config_tx[0]);
+
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8726_TX_CTRL2,
+ params->xgxs_config_tx[1]);
+ }
+ break;
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072:
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073:
+ {
+ u16 tmp1;
+ u16 rx_alarm_ctrl_val;
+ u16 lasi_ctrl_val;
+ if (ext_phy_type ==
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072) {
+ rx_alarm_ctrl_val = 0x400;
+ lasi_ctrl_val = 0x0004;
+ } else {
+ rx_alarm_ctrl_val = (1<<2);
+ lasi_ctrl_val = 0x0004;
+ }
+
+ /* enable LASI */
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_RX_ALARM_CTRL,
+ rx_alarm_ctrl_val);
+
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_LASI_CTRL,
+ lasi_ctrl_val);
+
+ bnx2x_8073_set_pause_cl37(params, vars);
+
+ if (ext_phy_type ==
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072)
+ bnx2x_bcm8072_external_rom_boot(params);
+ else
+ /* In case of 8073 with long xaui lines,
+ don't set the 8073 xaui low power*/
+ bnx2x_bcm8073_set_xaui_low_power_mode(params);
+
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_M8051_MSGOUT_REG,
+ &tmp1);
+
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_RX_ALARM, &tmp1);
+
+ DP(NETIF_MSG_LINK, "Before rom RX_ALARM(port1):"
+ "0x%x\n", tmp1);
+
+ /* If this is forced speed, set to KR or KX
+ * (all other are not supported)
+ */
+ if (params->loopback_mode == LOOPBACK_EXT) {
+ bnx2x_bcm807x_force_10G(params);
+ DP(NETIF_MSG_LINK,
+ "Forced speed 10G on 807X\n");
+ break;
+ } else {
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type, ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_BCM_CTRL,
+ 0x0002);
+ }
+ if (params->req_line_speed != SPEED_AUTO_NEG) {
+ if (params->req_line_speed == SPEED_10000) {
+ val = (1<<7);
+ } else if (params->req_line_speed ==
+ SPEED_2500) {
+ val = (1<<5);
+ /* Note that 2.5G works only
+ when used with 1G advertisment */
+ } else
+ val = (1<<5);
+ } else {
+
+ val = 0;
+ if (params->speed_cap_mask &
+ PORT_HW_CFG_SPEED_CAPABILITY_D0_10G)
+ val |= (1<<7);
+
+ /* Note that 2.5G works only when
+ used with 1G advertisment */
+ if (params->speed_cap_mask &
+ (PORT_HW_CFG_SPEED_CAPABILITY_D0_1G |
+ PORT_HW_CFG_SPEED_CAPABILITY_D0_2_5G))
+ val |= (1<<5);
+ DP(NETIF_MSG_LINK,
+ "807x autoneg val = 0x%x\n", val);
+ }
+
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_ADV, val);
+ if (ext_phy_type ==
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073) {
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_8073_2_5G, &tmp1);
+
+ if (((params->speed_cap_mask &
+ PORT_HW_CFG_SPEED_CAPABILITY_D0_2_5G) &&
+ (params->req_line_speed ==
+ SPEED_AUTO_NEG)) ||
+ (params->req_line_speed ==
+ SPEED_2500)) {
+ u16 phy_ver;
+ /* Allow 2.5G for A1 and above */
+ bnx2x_cl45_read(bp, params->port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8073_CHIP_REV, &phy_ver);
+ DP(NETIF_MSG_LINK, "Add 2.5G\n");
+ if (phy_ver > 0)
+ tmp1 |= 1;
+ else
+ tmp1 &= 0xfffe;
+ } else {
+ DP(NETIF_MSG_LINK, "Disable 2.5G\n");
+ tmp1 &= 0xfffe;
+ }
+
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_8073_2_5G, tmp1);
+ }
+
+ /* Add support for CL37 (passive mode) II */
+
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_CL37_FC_LD,
+ &tmp1);
+
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_CL37_FC_LD, (tmp1 |
+ ((params->req_duplex == DUPLEX_FULL) ?
+ 0x20 : 0x40)));
+
+ /* Add support for CL37 (passive mode) III */
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_CL37_AN, 0x1000);
+
+ if (ext_phy_type ==
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073) {
+ /* The SNR will improve about 2db by changing
+ BW and FEE main tap. Rest commands are executed
+ after link is up*/
+ /*Change FFE main cursor to 5 in EDC register*/
+ if (bnx2x_8073_is_snr_needed(params))
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_EDC_FFE_MAIN,
+ 0xFB0C);
+
+ /* Enable FEC (Forware Error Correction)
+ Request in the AN */
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_ADV2, &tmp1);
+
+ tmp1 |= (1<<15);
+
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_ADV2, tmp1);
+
+ }
+
+ bnx2x_ext_phy_set_pause(params, vars);
+
+ /* Restart autoneg */
+ msleep(500);
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_CTRL, 0x1200);
+ DP(NETIF_MSG_LINK, "807x Autoneg Restart: "
+ "Advertise 1G=%x, 10G=%x\n",
+ ((val & (1<<5)) > 0),
+ ((val & (1<<7)) > 0));
+ break;
+ }
+
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727:
+ {
+ u16 tmp1;
+ u16 rx_alarm_ctrl_val;
+ u16 lasi_ctrl_val;
+
+ /* Enable PMD link, MOD_ABS_FLT, and 1G link alarm */
+
+ u16 mod_abs;
+ rx_alarm_ctrl_val = (1<<2) | (1<<5) ;
+ lasi_ctrl_val = 0x0004;
+
+ DP(NETIF_MSG_LINK, "Initializing BCM8727\n");
+ /* enable LASI */
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_RX_ALARM_CTRL,
+ rx_alarm_ctrl_val);
+
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_LASI_CTRL,
+ lasi_ctrl_val);
+
+ /* Initially configure MOD_ABS to interrupt when
+ module is presence( bit 8) */
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_PHY_IDENTIFIER, &mod_abs);
+ /* Set EDC off by setting OPTXLOS signal input to low
+ (bit 9).
+ When the EDC is off it locks onto a reference clock and
+ avoids becoming 'lost'.*/
+ mod_abs &= ~((1<<8) | (1<<9));
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_PHY_IDENTIFIER, mod_abs);
+
+ /* Make MOD_ABS give interrupt on change */
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8727_PCS_OPT_CTRL,
+ &val);
+ val |= (1<<12);
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8727_PCS_OPT_CTRL,
+ val);
+
+ /* Set 8727 GPIOs to input to allow reading from the
+ 8727 GPIO0 status which reflect SFP+ module
+ over-current */
+
+ bnx2x_cl45_read(bp, params->port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8727_PCS_OPT_CTRL,
+ &val);
+ val &= 0xff8f; /* Reset bits 4-6 */
+ bnx2x_cl45_write(bp, params->port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8727_PCS_OPT_CTRL,
+ val);
+
+ bnx2x_8727_power_module(bp, params, ext_phy_addr, 1);
+ bnx2x_bcm8073_set_xaui_low_power_mode(params);
+
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_M8051_MSGOUT_REG,
+ &tmp1);
+
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_RX_ALARM, &tmp1);
+
+ /* Set option 1G speed */
+ if (params->req_line_speed == SPEED_1000) {
+
+ DP(NETIF_MSG_LINK, "Setting 1G force\n");
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_CTRL, 0x40);
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_10G_CTRL2, 0xD);
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_10G_CTRL2, &tmp1);
+ DP(NETIF_MSG_LINK, "1.7 = 0x%x\n", tmp1);
+
+ } else if ((params->req_line_speed ==
+ SPEED_AUTO_NEG) &&
+ ((params->speed_cap_mask &
+ PORT_HW_CFG_SPEED_CAPABILITY_D0_1G))) {
+
+ DP(NETIF_MSG_LINK, "Setting 1G clause37\n");
+ bnx2x_cl45_write(bp, params->port, ext_phy_type,
+ ext_phy_addr, MDIO_AN_DEVAD,
+ MDIO_PMA_REG_8727_MISC_CTRL, 0);
+ bnx2x_cl45_write(bp, params->port, ext_phy_type,
+ ext_phy_addr, MDIO_AN_DEVAD,
+ MDIO_AN_REG_CL37_AN, 0x1300);
+ } else {
+ /* Since the 8727 has only single reset pin,
+ need to set the 10G registers although it is
+ default */
+ bnx2x_cl45_write(bp, params->port, ext_phy_type,
+ ext_phy_addr, MDIO_AN_DEVAD,
+ MDIO_AN_REG_CTRL, 0x0020);
+ bnx2x_cl45_write(bp, params->port, ext_phy_type,
+ ext_phy_addr, MDIO_AN_DEVAD,
+ 0x7, 0x0100);
+ bnx2x_cl45_write(bp, params->port, ext_phy_type,
+ ext_phy_addr, MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_CTRL, 0x2040);
+ bnx2x_cl45_write(bp, params->port, ext_phy_type,
+ ext_phy_addr, MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_10G_CTRL2, 0x0008);
+ }
+
+ /* Set 2-wire transfer rate of SFP+ module EEPROM
+ * to 100Khz since some DACs(direct attached cables) do
+ * not work at 400Khz.
+ */
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8727_TWO_WIRE_SLAVE_ADDR,
+ 0xa001);
+
+ /* Set TX PreEmphasis if needed */
+ if ((params->feature_config_flags &
+ FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED)) {
+ DP(NETIF_MSG_LINK, "Setting TX_CTRL1 0x%x,"
+ "TX_CTRL2 0x%x\n",
+ params->xgxs_config_tx[0],
+ params->xgxs_config_tx[1]);
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8727_TX_CTRL1,
+ params->xgxs_config_tx[0]);
+
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8727_TX_CTRL2,
+ params->xgxs_config_tx[1]);
+ }
+
+ break;
+ }
+
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101:
+ {
+ u16 fw_ver1, fw_ver2;
+ DP(NETIF_MSG_LINK,
+ "Setting the SFX7101 LASI indication\n");
+
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_LASI_CTRL, 0x1);
+ DP(NETIF_MSG_LINK,
+ "Setting the SFX7101 LED to blink on traffic\n");
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_7107_LED_CNTL, (1<<3));
+
+ bnx2x_ext_phy_set_pause(params, vars);
+ /* Restart autoneg */
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_CTRL, &val);
+ val |= 0x200;
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_CTRL, val);
+
+ /* Save spirom version */
+ bnx2x_cl45_read(bp, params->port, ext_phy_type,
+ ext_phy_addr, MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_7101_VER1, &fw_ver1);
+
+ bnx2x_cl45_read(bp, params->port, ext_phy_type,
+ ext_phy_addr, MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_7101_VER2, &fw_ver2);
+
+ bnx2x_save_spirom_version(params->bp, params->port,
+ params->shmem_base,
+ (u32)(fw_ver1<<16 | fw_ver2));
+ break;
+ }
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481:
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823:
+ /* This phy uses the NIG latch mechanism since link
+ indication arrives through its LED4 and not via
+ its LASI signal, so we get steady signal
+ instead of clear on read */
+ bnx2x_bits_en(bp, NIG_REG_LATCH_BC_0 + params->port*4,
+ 1 << NIG_LATCH_BC_ENABLE_MI_INT);
+
+ bnx2x_cl45_write(bp, params->port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_CTRL, 0x0000);
+
+ bnx2x_8481_set_led4(params, ext_phy_type, ext_phy_addr);
+ if (params->req_line_speed == SPEED_AUTO_NEG) {
+
+ u16 autoneg_val, an_1000_val, an_10_100_val;
+ /* set 1000 speed advertisement */
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_8481_1000T_CTRL,
+ &an_1000_val);
+
+ if (params->speed_cap_mask &
+ PORT_HW_CFG_SPEED_CAPABILITY_D0_1G) {
+ an_1000_val |= (1<<8);
+ if (params->req_duplex == DUPLEX_FULL)
+ an_1000_val |= (1<<9);
+ DP(NETIF_MSG_LINK, "Advertising 1G\n");
+ } else
+ an_1000_val &= ~((1<<8) | (1<<9));
+
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_8481_1000T_CTRL,
+ an_1000_val);
+
+ /* set 100 speed advertisement */
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_8481_LEGACY_AN_ADV,
+ &an_10_100_val);
+
+ if (params->speed_cap_mask &
+ (PORT_HW_CFG_SPEED_CAPABILITY_D0_100M_FULL |
+ PORT_HW_CFG_SPEED_CAPABILITY_D0_100M_HALF)) {
+ an_10_100_val |= (1<<7);
+ if (params->req_duplex == DUPLEX_FULL)
+ an_10_100_val |= (1<<8);
+ DP(NETIF_MSG_LINK,
+ "Advertising 100M\n");
+ } else
+ an_10_100_val &= ~((1<<7) | (1<<8));
+
+ /* set 10 speed advertisement */
+ if (params->speed_cap_mask &
+ (PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_FULL |
+ PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_HALF)) {
+ an_10_100_val |= (1<<5);
+ if (params->req_duplex == DUPLEX_FULL)
+ an_10_100_val |= (1<<6);
+ DP(NETIF_MSG_LINK, "Advertising 10M\n");
+ }
+ else
+ an_10_100_val &= ~((1<<5) | (1<<6));
+
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_8481_LEGACY_AN_ADV,
+ an_10_100_val);
+
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_8481_LEGACY_MII_CTRL,
+ &autoneg_val);
+
+ /* Disable forced speed */
+ autoneg_val &= ~(1<<6|1<<13);
+
+ /* Enable autoneg and restart autoneg
+ for legacy speeds */
+ autoneg_val |= (1<<9|1<<12);
+
+ if (params->req_duplex == DUPLEX_FULL)
+ autoneg_val |= (1<<8);
+ else
+ autoneg_val &= ~(1<<8);
+
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_8481_LEGACY_MII_CTRL,
+ autoneg_val);
+
+ if (params->speed_cap_mask &
+ PORT_HW_CFG_SPEED_CAPABILITY_D0_10G) {
+ DP(NETIF_MSG_LINK, "Advertising 10G\n");
+ /* Restart autoneg for 10G*/
+
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_CTRL, 0x3200);
+ }
+ } else {
+ /* Force speed */
+ u16 autoneg_ctrl, pma_ctrl;
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_8481_LEGACY_MII_CTRL,
+ &autoneg_ctrl);
+
+ /* Disable autoneg */
+ autoneg_ctrl &= ~(1<<12);
+
+ /* Set 1000 force */
+ switch (params->req_line_speed) {
+ case SPEED_10000:
+ DP(NETIF_MSG_LINK,
+ "Unable to set 10G force !\n");
+ break;
+ case SPEED_1000:
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_CTRL,
+ &pma_ctrl);
+ autoneg_ctrl &= ~(1<<13);
+ autoneg_ctrl |= (1<<6);
+ pma_ctrl &= ~(1<<13);
+ pma_ctrl |= (1<<6);
+ DP(NETIF_MSG_LINK,
+ "Setting 1000M force\n");
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_CTRL,
+ pma_ctrl);
+ break;
+ case SPEED_100:
+ autoneg_ctrl |= (1<<13);
+ autoneg_ctrl &= ~(1<<6);
+ DP(NETIF_MSG_LINK,
+ "Setting 100M force\n");
+ break;
+ case SPEED_10:
+ autoneg_ctrl &= ~(1<<13);
+ autoneg_ctrl &= ~(1<<6);
+ DP(NETIF_MSG_LINK,
+ "Setting 10M force\n");
+ break;
+ }
+
+ /* Duplex mode */
+ if (params->req_duplex == DUPLEX_FULL) {
+ autoneg_ctrl |= (1<<8);
+ DP(NETIF_MSG_LINK,
+ "Setting full duplex\n");
+ } else
+ autoneg_ctrl &= ~(1<<8);
+
+ /* Update autoneg ctrl and pma ctrl */
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_8481_LEGACY_MII_CTRL,
+ autoneg_ctrl);
+ }
+
+ /* Save spirom version */
+ bnx2x_save_8481_spirom_version(bp, params->port,
+ ext_phy_addr,
+ params->shmem_base);
+ break;
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE:
+ DP(NETIF_MSG_LINK,
+ "XGXS PHY Failure detected 0x%x\n",
+ params->ext_phy_config);
+ rc = -EINVAL;
+ break;
+ default:
+ DP(NETIF_MSG_LINK, "BAD XGXS ext_phy_config 0x%x\n",
+ params->ext_phy_config);
+ rc = -EINVAL;
+ break;
+ }
+
+ } else { /* SerDes */
+
+ ext_phy_type = SERDES_EXT_PHY_TYPE(params->ext_phy_config);
+ switch (ext_phy_type) {
+ case PORT_HW_CFG_SERDES_EXT_PHY_TYPE_DIRECT:
+ DP(NETIF_MSG_LINK, "SerDes Direct\n");
+ break;
+
+ case PORT_HW_CFG_SERDES_EXT_PHY_TYPE_BCM5482:
+ DP(NETIF_MSG_LINK, "SerDes 5482\n");
+ break;
+
+ default:
+ DP(NETIF_MSG_LINK, "BAD SerDes ext_phy_config 0x%x\n",
+ params->ext_phy_config);
+ break;
+ }
+ }
+ return rc;
+}
+
+static void bnx2x_8727_handle_mod_abs(struct link_params *params)
+{
+ struct bnx2x *bp = params->bp;
+ u16 mod_abs, rx_alarm_status;
+ u8 ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config);
+ u32 val = REG_RD(bp, params->shmem_base +
+ offsetof(struct shmem_region, dev_info.
+ port_feature_config[params->port].
+ config));
+ bnx2x_cl45_read(bp, params->port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_PHY_IDENTIFIER, &mod_abs);
+ if (mod_abs & (1<<8)) {
+
+ /* Module is absent */
+ DP(NETIF_MSG_LINK, "MOD_ABS indication "
+ "show module is absent\n");
+
+ /* 1. Set mod_abs to detect next module
+ presence event
+ 2. Set EDC off by setting OPTXLOS signal input to low
+ (bit 9).
+ When the EDC is off it locks onto a reference clock and
+ avoids becoming 'lost'.*/
+ mod_abs &= ~((1<<8)|(1<<9));
+ bnx2x_cl45_write(bp, params->port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_PHY_IDENTIFIER, mod_abs);
+
+ /* Clear RX alarm since it stays up as long as
+ the mod_abs wasn't changed */
+ bnx2x_cl45_read(bp, params->port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_RX_ALARM, &rx_alarm_status);
+
+ } else {
+ /* Module is present */
+ DP(NETIF_MSG_LINK, "MOD_ABS indication "
+ "show module is present\n");
+ /* First thing, disable transmitter,
+ and if the module is ok, the
+ module_detection will enable it*/
+
+ /* 1. Set mod_abs to detect next module
+ absent event ( bit 8)
+ 2. Restore the default polarity of the OPRXLOS signal and
+ this signal will then correctly indicate the presence or
+ absence of the Rx signal. (bit 9) */
+ mod_abs |= ((1<<8)|(1<<9));
+ bnx2x_cl45_write(bp, params->port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_PHY_IDENTIFIER, mod_abs);
+
+ /* Clear RX alarm since it stays up as long as
+ the mod_abs wasn't changed. This is need to be done
+ before calling the module detection, otherwise it will clear
+ the link update alarm */
+ bnx2x_cl45_read(bp, params->port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_RX_ALARM, &rx_alarm_status);
+
+
+ if ((val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) ==
+ PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_DISABLE_TX_LASER)
+ bnx2x_sfp_set_transmitter(bp, params->port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727,
+ ext_phy_addr, 0);
+
+ if (bnx2x_wait_for_sfp_module_initialized(params)
+ == 0)
+ bnx2x_sfp_module_detection(params);
+ else
+ DP(NETIF_MSG_LINK, "SFP+ module is not initialized\n");
+ }
+
+ DP(NETIF_MSG_LINK, "8727 RX_ALARM_STATUS 0x%x\n",
+ rx_alarm_status);
+ /* No need to check link status in case of
+ module plugged in/out */
+}
+
+
+static u8 bnx2x_ext_phy_is_link_up(struct link_params *params,
+ struct link_vars *vars,
+ u8 is_mi_int)
+{
+ struct bnx2x *bp = params->bp;
+ u32 ext_phy_type;
+ u8 ext_phy_addr;
+ u16 val1 = 0, val2;
+ u16 rx_sd, pcs_status;
+ u8 ext_phy_link_up = 0;
+ u8 port = params->port;
+
+ if (vars->phy_flags & PHY_XGXS_FLAG) {
+ ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config);
+ ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config);
+ switch (ext_phy_type) {
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT:
+ DP(NETIF_MSG_LINK, "XGXS Direct\n");
+ ext_phy_link_up = 1;
+ break;
+
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705:
+ DP(NETIF_MSG_LINK, "XGXS 8705\n");
+ bnx2x_cl45_read(bp, params->port, ext_phy_type,
+ ext_phy_addr,
+ MDIO_WIS_DEVAD,
+ MDIO_WIS_REG_LASI_STATUS, &val1);
+ DP(NETIF_MSG_LINK, "8705 LASI status 0x%x\n", val1);
+
+ bnx2x_cl45_read(bp, params->port, ext_phy_type,
+ ext_phy_addr,
+ MDIO_WIS_DEVAD,
+ MDIO_WIS_REG_LASI_STATUS, &val1);
+ DP(NETIF_MSG_LINK, "8705 LASI status 0x%x\n", val1);
+
+ bnx2x_cl45_read(bp, params->port, ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_RX_SD, &rx_sd);
+
+ bnx2x_cl45_read(bp, params->port, ext_phy_type,
+ ext_phy_addr,
+ 1,
+ 0xc809, &val1);
+ bnx2x_cl45_read(bp, params->port, ext_phy_type,
+ ext_phy_addr,
+ 1,
+ 0xc809, &val1);
+
+ DP(NETIF_MSG_LINK, "8705 1.c809 val=0x%x\n", val1);
+ ext_phy_link_up = ((rx_sd & 0x1) && (val1 & (1<<9)) &&
+ ((val1 & (1<<8)) == 0));
+ if (ext_phy_link_up)
+ vars->line_speed = SPEED_10000;
+ break;
+
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706:
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726:
+ DP(NETIF_MSG_LINK, "XGXS 8706/8726\n");
+ /* Clear RX Alarm*/
+ bnx2x_cl45_read(bp, params->port, ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD, MDIO_PMA_REG_RX_ALARM,
+ &val2);
+ /* clear LASI indication*/
+ bnx2x_cl45_read(bp, params->port, ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD, MDIO_PMA_REG_LASI_STATUS,
+ &val1);
+ bnx2x_cl45_read(bp, params->port, ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD, MDIO_PMA_REG_LASI_STATUS,
+ &val2);
+ DP(NETIF_MSG_LINK, "8706/8726 LASI status 0x%x-->"
+ "0x%x\n", val1, val2);
+
+ bnx2x_cl45_read(bp, params->port, ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD, MDIO_PMA_REG_RX_SD,
+ &rx_sd);
+ bnx2x_cl45_read(bp, params->port, ext_phy_type,
+ ext_phy_addr,
+ MDIO_PCS_DEVAD, MDIO_PCS_REG_STATUS,
+ &pcs_status);
+ bnx2x_cl45_read(bp, params->port, ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD, MDIO_AN_REG_LINK_STATUS,
+ &val2);
+ bnx2x_cl45_read(bp, params->port, ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD, MDIO_AN_REG_LINK_STATUS,
+ &val2);
+
+ DP(NETIF_MSG_LINK, "8706/8726 rx_sd 0x%x"
+ " pcs_status 0x%x 1Gbps link_status 0x%x\n",
+ rx_sd, pcs_status, val2);
+ /* link is up if both bit 0 of pmd_rx_sd and
+ * bit 0 of pcs_status are set, or if the autoneg bit
+ 1 is set
+ */
+ ext_phy_link_up = ((rx_sd & pcs_status & 0x1) ||
+ (val2 & (1<<1)));
+ if (ext_phy_link_up) {
+ if (ext_phy_type ==
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726) {
+ /* If transmitter is disabled,
+ ignore false link up indication */
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_PHY_IDENTIFIER,
+ &val1);
+ if (val1 & (1<<15)) {
+ DP(NETIF_MSG_LINK, "Tx is "
+ "disabled\n");
+ ext_phy_link_up = 0;
+ break;
+ }
+ }
+ if (val2 & (1<<1))
+ vars->line_speed = SPEED_1000;
+ else
+ vars->line_speed = SPEED_10000;
+ }
+ break;
+
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727:
+ {
+ u16 link_status = 0;
+ u16 rx_alarm_status;
+ /* Check the LASI */
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_RX_ALARM, &rx_alarm_status);
+
+ DP(NETIF_MSG_LINK, "8727 RX_ALARM_STATUS 0x%x\n",
+ rx_alarm_status);
+
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_LASI_STATUS, &val1);
+
+ DP(NETIF_MSG_LINK,
+ "8727 LASI status 0x%x\n",
+ val1);
+
+ /* Clear MSG-OUT */
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_M8051_MSGOUT_REG,
+ &val1);
+
+ /*
+ * If a module is present and there is need to check
+ * for over current
+ */
+ if (!(params->feature_config_flags &
+ FEATURE_CONFIG_BCM8727_NOC) &&
+ !(rx_alarm_status & (1<<5))) {
+ /* Check over-current using 8727 GPIO0 input*/
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8727_GPIO_CTRL,
+ &val1);
+
+ if ((val1 & (1<<8)) == 0) {
+ DP(NETIF_MSG_LINK, "8727 Power fault"
+ " has been detected on "
+ "port %d\n",
+ params->port);
+ netdev_err(bp->dev, "Error: Power fault on Port %d has been detected and the power to that SFP+ module has been removed to prevent failure of the card. Please remove the SFP+ module and restart the system to clear this error.\n",
+ params->port);
+ /*
+ * Disable all RX_ALARMs except for
+ * mod_abs
+ */
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_RX_ALARM_CTRL,
+ (1<<5));
+
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_PHY_IDENTIFIER,
+ &val1);
+ /* Wait for module_absent_event */
+ val1 |= (1<<8);
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_PHY_IDENTIFIER,
+ val1);
+ /* Clear RX alarm */
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_RX_ALARM,
+ &rx_alarm_status);
+ break;
+ }
+ } /* Over current check */
+
+ /* When module absent bit is set, check module */
+ if (rx_alarm_status & (1<<5)) {
+ bnx2x_8727_handle_mod_abs(params);
+ /* Enable all mod_abs and link detection bits */
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_RX_ALARM_CTRL,
+ ((1<<5) | (1<<2)));
+ }
+
+ /* If transmitter is disabled,
+ ignore false link up indication */
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_PHY_IDENTIFIER,
+ &val1);
+ if (val1 & (1<<15)) {
+ DP(NETIF_MSG_LINK, "Tx is disabled\n");
+ ext_phy_link_up = 0;
+ break;
+ }
+
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8073_SPEED_LINK_STATUS,
+ &link_status);
+
+ /* Bits 0..2 --> speed detected,
+ bits 13..15--> link is down */
+ if ((link_status & (1<<2)) &&
+ (!(link_status & (1<<15)))) {
+ ext_phy_link_up = 1;
+ vars->line_speed = SPEED_10000;
+ } else if ((link_status & (1<<0)) &&
+ (!(link_status & (1<<13)))) {
+ ext_phy_link_up = 1;
+ vars->line_speed = SPEED_1000;
+ DP(NETIF_MSG_LINK,
+ "port %x: External link"
+ " up in 1G\n", params->port);
+ } else {
+ ext_phy_link_up = 0;
+ DP(NETIF_MSG_LINK,
+ "port %x: External link"
+ " is down\n", params->port);
+ }
+ break;
+ }
+
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072:
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073:
+ {
+ u16 link_status = 0;
+ u16 an1000_status = 0;
+
+ if (ext_phy_type ==
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072) {
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PCS_DEVAD,
+ MDIO_PCS_REG_LASI_STATUS, &val1);
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PCS_DEVAD,
+ MDIO_PCS_REG_LASI_STATUS, &val2);
+ DP(NETIF_MSG_LINK,
+ "870x LASI status 0x%x->0x%x\n",
+ val1, val2);
+ } else {
+ /* In 8073, port1 is directed through emac0 and
+ * port0 is directed through emac1
+ */
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_LASI_STATUS, &val1);
+
+ DP(NETIF_MSG_LINK,
+ "8703 LASI status 0x%x\n",
+ val1);
+ }
+
+ /* clear the interrupt LASI status register */
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PCS_DEVAD,
+ MDIO_PCS_REG_STATUS, &val2);
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PCS_DEVAD,
+ MDIO_PCS_REG_STATUS, &val1);
+ DP(NETIF_MSG_LINK, "807x PCS status 0x%x->0x%x\n",
+ val2, val1);
+ /* Clear MSG-OUT */
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_M8051_MSGOUT_REG,
+ &val1);
+
+ /* Check the LASI */
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_RX_ALARM, &val2);
+
+ DP(NETIF_MSG_LINK, "KR 0x9003 0x%x\n", val2);
+
+ /* Check the link status */
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PCS_DEVAD,
+ MDIO_PCS_REG_STATUS, &val2);
+ DP(NETIF_MSG_LINK, "KR PCS status 0x%x\n", val2);
+
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_STATUS, &val2);
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_STATUS, &val1);
+ ext_phy_link_up = ((val1 & 4) == 4);
+ DP(NETIF_MSG_LINK, "PMA_REG_STATUS=0x%x\n", val1);
+ if (ext_phy_type ==
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073) {
+
+ if (ext_phy_link_up &&
+ ((params->req_line_speed !=
+ SPEED_10000))) {
+ if (bnx2x_bcm8073_xaui_wa(params)
+ != 0) {
+ ext_phy_link_up = 0;
+ break;
+ }
+ }
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_LINK_STATUS,
+ &an1000_status);
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_LINK_STATUS,
+ &an1000_status);
+
+ /* Check the link status on 1.1.2 */
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_STATUS, &val2);
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_STATUS, &val1);
+ DP(NETIF_MSG_LINK, "KR PMA status 0x%x->0x%x,"
+ "an_link_status=0x%x\n",
+ val2, val1, an1000_status);
+
+ ext_phy_link_up = (((val1 & 4) == 4) ||
+ (an1000_status & (1<<1)));
+ if (ext_phy_link_up &&
+ bnx2x_8073_is_snr_needed(params)) {
+ /* The SNR will improve about 2dbby
+ changing the BW and FEE main tap.*/
+
+ /* The 1st write to change FFE main
+ tap is set before restart AN */
+ /* Change PLL Bandwidth in EDC
+ register */
+ bnx2x_cl45_write(bp, port, ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_PLL_BANDWIDTH,
+ 0x26BC);
+
+ /* Change CDR Bandwidth in EDC
+ register */
+ bnx2x_cl45_write(bp, port, ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_CDR_BANDWIDTH,
+ 0x0333);
+ }
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8073_SPEED_LINK_STATUS,
+ &link_status);
+
+ /* Bits 0..2 --> speed detected,
+ bits 13..15--> link is down */
+ if ((link_status & (1<<2)) &&
+ (!(link_status & (1<<15)))) {
+ ext_phy_link_up = 1;
+ vars->line_speed = SPEED_10000;
+ DP(NETIF_MSG_LINK,
+ "port %x: External link"
+ " up in 10G\n", params->port);
+ } else if ((link_status & (1<<1)) &&
+ (!(link_status & (1<<14)))) {
+ ext_phy_link_up = 1;
+ vars->line_speed = SPEED_2500;
+ DP(NETIF_MSG_LINK,
+ "port %x: External link"
+ " up in 2.5G\n", params->port);
+ } else if ((link_status & (1<<0)) &&
+ (!(link_status & (1<<13)))) {
+ ext_phy_link_up = 1;
+ vars->line_speed = SPEED_1000;
+ DP(NETIF_MSG_LINK,
+ "port %x: External link"
+ " up in 1G\n", params->port);
+ } else {
+ ext_phy_link_up = 0;
+ DP(NETIF_MSG_LINK,
+ "port %x: External link"
+ " is down\n", params->port);
+ }
+ } else {
+ /* See if 1G link is up for the 8072 */
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_LINK_STATUS,
+ &an1000_status);
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_LINK_STATUS,
+ &an1000_status);
+ if (an1000_status & (1<<1)) {
+ ext_phy_link_up = 1;
+ vars->line_speed = SPEED_1000;
+ DP(NETIF_MSG_LINK,
+ "port %x: External link"
+ " up in 1G\n", params->port);
+ } else if (ext_phy_link_up) {
+ ext_phy_link_up = 1;
+ vars->line_speed = SPEED_10000;
+ DP(NETIF_MSG_LINK,
+ "port %x: External link"
+ " up in 10G\n", params->port);
+ }
+ }
+
+
+ break;
+ }
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101:
+ bnx2x_cl45_read(bp, params->port, ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_LASI_STATUS, &val2);
+ bnx2x_cl45_read(bp, params->port, ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_LASI_STATUS, &val1);
+ DP(NETIF_MSG_LINK,
+ "10G-base-T LASI status 0x%x->0x%x\n",
+ val2, val1);
+ bnx2x_cl45_read(bp, params->port, ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_STATUS, &val2);
+ bnx2x_cl45_read(bp, params->port, ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_STATUS, &val1);
+ DP(NETIF_MSG_LINK,
+ "10G-base-T PMA status 0x%x->0x%x\n",
+ val2, val1);
+ ext_phy_link_up = ((val1 & 4) == 4);
+ /* if link is up
+ * print the AN outcome of the SFX7101 PHY
+ */
+ if (ext_phy_link_up) {
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_MASTER_STATUS,
+ &val2);
+ vars->line_speed = SPEED_10000;
+ DP(NETIF_MSG_LINK,
+ "SFX7101 AN status 0x%x->Master=%x\n",
+ val2,
+ (val2 & (1<<14)));
+ }
+ break;
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481:
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823:
+ /* Check 10G-BaseT link status */
+ /* Check PMD signal ok */
+ bnx2x_cl45_read(bp, params->port, ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ 0xFFFA,
+ &val1);
+ bnx2x_cl45_read(bp, params->port, ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8481_PMD_SIGNAL,
+ &val2);
+ DP(NETIF_MSG_LINK, "PMD_SIGNAL 1.a811 = 0x%x\n", val2);
+
+ /* Check link 10G */
+ if (val2 & (1<<11)) {
+ vars->line_speed = SPEED_10000;
+ ext_phy_link_up = 1;
+ bnx2x_8481_set_10G_led_mode(params,
+ ext_phy_type,
+ ext_phy_addr);
+ } else { /* Check Legacy speed link */
+ u16 legacy_status, legacy_speed;
+
+ /* Enable expansion register 0x42
+ (Operation mode status) */
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_8481_EXPANSION_REG_ACCESS,
+ 0xf42);
+
+ /* Get legacy speed operation status */
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_8481_EXPANSION_REG_RD_RW,
+ &legacy_status);
+
+ DP(NETIF_MSG_LINK, "Legacy speed status"
+ " = 0x%x\n", legacy_status);
+ ext_phy_link_up = ((legacy_status & (1<<11))
+ == (1<<11));
+ if (ext_phy_link_up) {
+ legacy_speed = (legacy_status & (3<<9));
+ if (legacy_speed == (0<<9))
+ vars->line_speed = SPEED_10;
+ else if (legacy_speed == (1<<9))
+ vars->line_speed =
+ SPEED_100;
+ else if (legacy_speed == (2<<9))
+ vars->line_speed =
+ SPEED_1000;
+ else /* Should not happen */
+ vars->line_speed = 0;
+
+ if (legacy_status & (1<<8))
+ vars->duplex = DUPLEX_FULL;
+ else
+ vars->duplex = DUPLEX_HALF;
+
+ DP(NETIF_MSG_LINK, "Link is up "
+ "in %dMbps, is_duplex_full"
+ "= %d\n",
+ vars->line_speed,
+ (vars->duplex == DUPLEX_FULL));
+ bnx2x_8481_set_legacy_led_mode(params,
+ ext_phy_type,
+ ext_phy_addr);
+ }
+ }
+ break;
+ default:
+ DP(NETIF_MSG_LINK, "BAD XGXS ext_phy_config 0x%x\n",
+ params->ext_phy_config);
+ ext_phy_link_up = 0;
+ break;
+ }
+ /* Set SGMII mode for external phy */
+ if (ext_phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) {
+ if (vars->line_speed < SPEED_1000)
+ vars->phy_flags |= PHY_SGMII_FLAG;
+ else
+ vars->phy_flags &= ~PHY_SGMII_FLAG;
+ }
+
+ } else { /* SerDes */
+ ext_phy_type = SERDES_EXT_PHY_TYPE(params->ext_phy_config);
+ switch (ext_phy_type) {
+ case PORT_HW_CFG_SERDES_EXT_PHY_TYPE_DIRECT:
+ DP(NETIF_MSG_LINK, "SerDes Direct\n");
+ ext_phy_link_up = 1;
+ break;
+
+ case PORT_HW_CFG_SERDES_EXT_PHY_TYPE_BCM5482:
+ DP(NETIF_MSG_LINK, "SerDes 5482\n");
+ ext_phy_link_up = 1;
+ break;
+
+ default:
+ DP(NETIF_MSG_LINK,
+ "BAD SerDes ext_phy_config 0x%x\n",
+ params->ext_phy_config);
+ ext_phy_link_up = 0;
+ break;
+ }
+ }
+
+ return ext_phy_link_up;
+}
+
+static void bnx2x_link_int_enable(struct link_params *params)
+{
+ u8 port = params->port;
+ u32 ext_phy_type;
+ u32 mask;
+ struct bnx2x *bp = params->bp;
+
+ /* setting the status to report on link up
+ for either XGXS or SerDes */
+
+ if (params->switch_cfg == SWITCH_CFG_10G) {
+ mask = (NIG_MASK_XGXS0_LINK10G |
+ NIG_MASK_XGXS0_LINK_STATUS);
+ DP(NETIF_MSG_LINK, "enabled XGXS interrupt\n");
+ ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config);
+ if ((ext_phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) &&
+ (ext_phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE) &&
+ (ext_phy_type !=
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_NOT_CONN)) {
+ mask |= NIG_MASK_MI_INT;
+ DP(NETIF_MSG_LINK, "enabled external phy int\n");
+ }
+
+ } else { /* SerDes */
+ mask = NIG_MASK_SERDES0_LINK_STATUS;
+ DP(NETIF_MSG_LINK, "enabled SerDes interrupt\n");
+ ext_phy_type = SERDES_EXT_PHY_TYPE(params->ext_phy_config);
+ if ((ext_phy_type !=
+ PORT_HW_CFG_SERDES_EXT_PHY_TYPE_DIRECT) &&
+ (ext_phy_type !=
+ PORT_HW_CFG_SERDES_EXT_PHY_TYPE_NOT_CONN)) {
+ mask |= NIG_MASK_MI_INT;
+ DP(NETIF_MSG_LINK, "enabled external phy int\n");
+ }
+ }
+ bnx2x_bits_en(bp,
+ NIG_REG_MASK_INTERRUPT_PORT0 + port*4,
+ mask);
+
+ DP(NETIF_MSG_LINK, "port %x, is_xgxs %x, int_status 0x%x\n", port,
+ (params->switch_cfg == SWITCH_CFG_10G),
+ REG_RD(bp, NIG_REG_STATUS_INTERRUPT_PORT0 + port*4));
+ DP(NETIF_MSG_LINK, " int_mask 0x%x, MI_INT %x, SERDES_LINK %x\n",
+ REG_RD(bp, NIG_REG_MASK_INTERRUPT_PORT0 + port*4),
+ REG_RD(bp, NIG_REG_EMAC0_STATUS_MISC_MI_INT + port*0x18),
+ REG_RD(bp, NIG_REG_SERDES0_STATUS_LINK_STATUS+port*0x3c));
+ DP(NETIF_MSG_LINK, " 10G %x, XGXS_LINK %x\n",
+ REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK10G + port*0x68),
+ REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK_STATUS + port*0x68));
+}
+
+static void bnx2x_8481_rearm_latch_signal(struct bnx2x *bp, u8 port,
+ u8 is_mi_int)
+{
+ u32 latch_status = 0, is_mi_int_status;
+ /* Disable the MI INT ( external phy int )
+ * by writing 1 to the status register. Link down indication
+ * is high-active-signal, so in this case we need to write the
+ * status to clear the XOR
+ */
+ /* Read Latched signals */
+ latch_status = REG_RD(bp,
+ NIG_REG_LATCH_STATUS_0 + port*8);
+ is_mi_int_status = REG_RD(bp,
+ NIG_REG_STATUS_INTERRUPT_PORT0 + port*4);
+ DP(NETIF_MSG_LINK, "original_signal = 0x%x, nig_status = 0x%x,"
+ "latch_status = 0x%x\n",
+ is_mi_int, is_mi_int_status, latch_status);
+ /* Handle only those with latched-signal=up.*/
+ if (latch_status & 1) {
+ /* For all latched-signal=up,Write original_signal to status */
+ if (is_mi_int)
+ bnx2x_bits_en(bp,
+ NIG_REG_STATUS_INTERRUPT_PORT0
+ + port*4,
+ NIG_STATUS_EMAC0_MI_INT);
+ else
+ bnx2x_bits_dis(bp,
+ NIG_REG_STATUS_INTERRUPT_PORT0
+ + port*4,
+ NIG_STATUS_EMAC0_MI_INT);
+ /* For all latched-signal=up : Re-Arm Latch signals */
+ REG_WR(bp, NIG_REG_LATCH_STATUS_0 + port*8,
+ (latch_status & 0xfffe) | (latch_status & 1));
+ }
+}
+/*
+ * link management
+ */
+static void bnx2x_link_int_ack(struct link_params *params,
+ struct link_vars *vars, u8 is_10g,
+ u8 is_mi_int)
+{
+ struct bnx2x *bp = params->bp;
+ u8 port = params->port;
+
+ /* first reset all status
+ * we assume only one line will be change at a time */
+ bnx2x_bits_dis(bp, NIG_REG_STATUS_INTERRUPT_PORT0 + port*4,
+ (NIG_STATUS_XGXS0_LINK10G |
+ NIG_STATUS_XGXS0_LINK_STATUS |
+ NIG_STATUS_SERDES0_LINK_STATUS));
+ if ((XGXS_EXT_PHY_TYPE(params->ext_phy_config)
+ == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481) ||
+ (XGXS_EXT_PHY_TYPE(params->ext_phy_config)
+ == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823)) {
+ bnx2x_8481_rearm_latch_signal(bp, port, is_mi_int);
+ }
+ if (vars->phy_link_up) {
+ if (is_10g) {
+ /* Disable the 10G link interrupt
+ * by writing 1 to the status register
+ */
+ DP(NETIF_MSG_LINK, "10G XGXS phy link up\n");
+ bnx2x_bits_en(bp,
+ NIG_REG_STATUS_INTERRUPT_PORT0 + port*4,
+ NIG_STATUS_XGXS0_LINK10G);
+
+ } else if (params->switch_cfg == SWITCH_CFG_10G) {
+ /* Disable the link interrupt
+ * by writing 1 to the relevant lane
+ * in the status register
+ */
+ u32 ser_lane = ((params->lane_config &
+ PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >>
+ PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT);
+
+ DP(NETIF_MSG_LINK, "%d speed XGXS phy link up\n",
+ vars->line_speed);
+ bnx2x_bits_en(bp,
+ NIG_REG_STATUS_INTERRUPT_PORT0 + port*4,
+ ((1 << ser_lane) <<
+ NIG_STATUS_XGXS0_LINK_STATUS_SIZE));
+
+ } else { /* SerDes */
+ DP(NETIF_MSG_LINK, "SerDes phy link up\n");
+ /* Disable the link interrupt
+ * by writing 1 to the status register
+ */
+ bnx2x_bits_en(bp,
+ NIG_REG_STATUS_INTERRUPT_PORT0 + port*4,
+ NIG_STATUS_SERDES0_LINK_STATUS);
+ }
+
+ } else { /* link_down */
+ }
+}
+
+static u8 bnx2x_format_ver(u32 num, u8 *str, u16 len)
+{
+ u8 *str_ptr = str;
+ u32 mask = 0xf0000000;
+ u8 shift = 8*4;
+ u8 digit;
+ if (len < 10) {
+ /* Need more than 10chars for this format */
+ *str_ptr = '\0';
+ return -EINVAL;
+ }
+ while (shift > 0) {
+
+ shift -= 4;
+ digit = ((num & mask) >> shift);
+ if (digit < 0xa)
+ *str_ptr = digit + '0';
+ else
+ *str_ptr = digit - 0xa + 'a';
+ str_ptr++;
+ mask = mask >> 4;
+ if (shift == 4*4) {
+ *str_ptr = ':';
+ str_ptr++;
+ }
+ }
+ *str_ptr = '\0';
+ return 0;
+}
+
+u8 bnx2x_get_ext_phy_fw_version(struct link_params *params, u8 driver_loaded,
+ u8 *version, u16 len)
+{
+ struct bnx2x *bp;
+ u32 ext_phy_type = 0;
+ u32 spirom_ver = 0;
+ u8 status;
+
+ if (version == NULL || params == NULL)
+ return -EINVAL;
+ bp = params->bp;
+
+ spirom_ver = REG_RD(bp, params->shmem_base +
+ offsetof(struct shmem_region,
+ port_mb[params->port].ext_phy_fw_version));
+
+ status = 0;
+ /* reset the returned value to zero */
+ ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config);
+ switch (ext_phy_type) {
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101:
+
+ if (len < 5)
+ return -EINVAL;
+
+ version[0] = (spirom_ver & 0xFF);
+ version[1] = (spirom_ver & 0xFF00) >> 8;
+ version[2] = (spirom_ver & 0xFF0000) >> 16;
+ version[3] = (spirom_ver & 0xFF000000) >> 24;
+ version[4] = '\0';
+
+ break;
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072:
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073:
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727:
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706:
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726:
+ status = bnx2x_format_ver(spirom_ver, version, len);
+ break;
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481:
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823:
+ spirom_ver = ((spirom_ver & 0xF80) >> 7) << 16 |
+ (spirom_ver & 0x7F);
+ status = bnx2x_format_ver(spirom_ver, version, len);
+ break;
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT:
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705:
+ version[0] = '\0';
+ break;
+
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE:
+ DP(NETIF_MSG_LINK, "bnx2x_get_ext_phy_fw_version:"
+ " type is FAILURE!\n");
+ status = -EINVAL;
+ break;
+
+ default:
+ break;
+ }
+ return status;
+}
+
+static void bnx2x_set_xgxs_loopback(struct link_params *params,
+ struct link_vars *vars,
+ u8 is_10g)
+{
+ u8 port = params->port;
+ struct bnx2x *bp = params->bp;
+
+ if (is_10g) {
+ u32 md_devad;
+
+ DP(NETIF_MSG_LINK, "XGXS 10G loopback enable\n");
+
+ /* change the uni_phy_addr in the nig */
+ md_devad = REG_RD(bp, (NIG_REG_XGXS0_CTRL_MD_DEVAD +
+ port*0x18));
+
+ REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_DEVAD + port*0x18, 0x5);
+
+ bnx2x_cl45_write(bp, port, 0,
+ params->phy_addr,
+ 5,
+ (MDIO_REG_BANK_AER_BLOCK +
+ (MDIO_AER_BLOCK_AER_REG & 0xf)),
+ 0x2800);
+
+ bnx2x_cl45_write(bp, port, 0,
+ params->phy_addr,
+ 5,
+ (MDIO_REG_BANK_CL73_IEEEB0 +
+ (MDIO_CL73_IEEEB0_CL73_AN_CONTROL & 0xf)),
+ 0x6041);
+ msleep(200);
+ /* set aer mmd back */
+ bnx2x_set_aer_mmd(params, vars);
+
+ /* and md_devad */
+ REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_DEVAD + port*0x18,
+ md_devad);
+
+ } else {
+ u16 mii_control;
+
+ DP(NETIF_MSG_LINK, "XGXS 1G loopback enable\n");
+
+ CL45_RD_OVER_CL22(bp, port,
+ params->phy_addr,
+ MDIO_REG_BANK_COMBO_IEEE0,
+ MDIO_COMBO_IEEE0_MII_CONTROL,
+ &mii_control);
+
+ CL45_WR_OVER_CL22(bp, port,
+ params->phy_addr,
+ MDIO_REG_BANK_COMBO_IEEE0,
+ MDIO_COMBO_IEEE0_MII_CONTROL,
+ (mii_control |
+ MDIO_COMBO_IEEO_MII_CONTROL_LOOPBACK));
+ }
+}
+
+
+static void bnx2x_ext_phy_loopback(struct link_params *params)
+{
+ struct bnx2x *bp = params->bp;
+ u8 ext_phy_addr;
+ u32 ext_phy_type;
+
+ if (params->switch_cfg == SWITCH_CFG_10G) {
+ ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config);
+ ext_phy_addr = XGXS_EXT_PHY_ADDR(params->ext_phy_config);
+ /* CL37 Autoneg Enabled */
+ switch (ext_phy_type) {
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT:
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_NOT_CONN:
+ DP(NETIF_MSG_LINK,
+ "ext_phy_loopback: We should not get here\n");
+ break;
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705:
+ DP(NETIF_MSG_LINK, "ext_phy_loopback: 8705\n");
+ break;
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706:
+ DP(NETIF_MSG_LINK, "ext_phy_loopback: 8706\n");
+ break;
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726:
+ DP(NETIF_MSG_LINK, "PMA/PMD ext_phy_loopback: 8726\n");
+ bnx2x_cl45_write(bp, params->port, ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_CTRL,
+ 0x0001);
+ break;
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101:
+ /* SFX7101_XGXS_TEST1 */
+ bnx2x_cl45_write(bp, params->port, ext_phy_type,
+ ext_phy_addr,
+ MDIO_XS_DEVAD,
+ MDIO_XS_SFX7101_XGXS_TEST1,
+ 0x100);
+ DP(NETIF_MSG_LINK,
+ "ext_phy_loopback: set ext phy loopback\n");
+ break;
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072:
+
+ break;
+ } /* switch external PHY type */
+ } else {
+ /* serdes */
+ ext_phy_type = SERDES_EXT_PHY_TYPE(params->ext_phy_config);
+ ext_phy_addr = (params->ext_phy_config &
+ PORT_HW_CFG_SERDES_EXT_PHY_ADDR_MASK)
+ >> PORT_HW_CFG_SERDES_EXT_PHY_ADDR_SHIFT;
+ }
+}
+
+
+/*
+ *------------------------------------------------------------------------
+ * bnx2x_override_led_value -
+ *
+ * Override the led value of the requsted led
+ *
+ *------------------------------------------------------------------------
+ */
+u8 bnx2x_override_led_value(struct bnx2x *bp, u8 port,
+ u32 led_idx, u32 value)
+{
+ u32 reg_val;
+
+ /* If port 0 then use EMAC0, else use EMAC1*/
+ u32 emac_base = (port) ? GRCBASE_EMAC1 : GRCBASE_EMAC0;
+
+ DP(NETIF_MSG_LINK,
+ "bnx2x_override_led_value() port %x led_idx %d value %d\n",
+ port, led_idx, value);
+
+ switch (led_idx) {
+ case 0: /* 10MB led */
+ /* Read the current value of the LED register in
+ the EMAC block */
+ reg_val = REG_RD(bp, emac_base + EMAC_REG_EMAC_LED);
+ /* Set the OVERRIDE bit to 1 */
+ reg_val |= EMAC_LED_OVERRIDE;
+ /* If value is 1, set the 10M_OVERRIDE bit,
+ otherwise reset it.*/
+ reg_val = (value == 1) ? (reg_val | EMAC_LED_10MB_OVERRIDE) :
+ (reg_val & ~EMAC_LED_10MB_OVERRIDE);
+ REG_WR(bp, emac_base + EMAC_REG_EMAC_LED, reg_val);
+ break;
+ case 1: /*100MB led */
+ /*Read the current value of the LED register in
+ the EMAC block */
+ reg_val = REG_RD(bp, emac_base + EMAC_REG_EMAC_LED);
+ /* Set the OVERRIDE bit to 1 */
+ reg_val |= EMAC_LED_OVERRIDE;
+ /* If value is 1, set the 100M_OVERRIDE bit,
+ otherwise reset it.*/
+ reg_val = (value == 1) ? (reg_val | EMAC_LED_100MB_OVERRIDE) :
+ (reg_val & ~EMAC_LED_100MB_OVERRIDE);
+ REG_WR(bp, emac_base + EMAC_REG_EMAC_LED, reg_val);
+ break;
+ case 2: /* 1000MB led */
+ /* Read the current value of the LED register in the
+ EMAC block */
+ reg_val = REG_RD(bp, emac_base + EMAC_REG_EMAC_LED);
+ /* Set the OVERRIDE bit to 1 */
+ reg_val |= EMAC_LED_OVERRIDE;
+ /* If value is 1, set the 1000M_OVERRIDE bit, otherwise
+ reset it. */
+ reg_val = (value == 1) ? (reg_val | EMAC_LED_1000MB_OVERRIDE) :
+ (reg_val & ~EMAC_LED_1000MB_OVERRIDE);
+ REG_WR(bp, emac_base + EMAC_REG_EMAC_LED, reg_val);
+ break;
+ case 3: /* 2500MB led */
+ /* Read the current value of the LED register in the
+ EMAC block*/
+ reg_val = REG_RD(bp, emac_base + EMAC_REG_EMAC_LED);
+ /* Set the OVERRIDE bit to 1 */
+ reg_val |= EMAC_LED_OVERRIDE;
+ /* If value is 1, set the 2500M_OVERRIDE bit, otherwise
+ reset it.*/
+ reg_val = (value == 1) ? (reg_val | EMAC_LED_2500MB_OVERRIDE) :
+ (reg_val & ~EMAC_LED_2500MB_OVERRIDE);
+ REG_WR(bp, emac_base + EMAC_REG_EMAC_LED, reg_val);
+ break;
+ case 4: /*10G led */
+ if (port == 0) {
+ REG_WR(bp, NIG_REG_LED_10G_P0,
+ value);
+ } else {
+ REG_WR(bp, NIG_REG_LED_10G_P1,
+ value);
+ }
+ break;
+ case 5: /* TRAFFIC led */
+ /* Find if the traffic control is via BMAC or EMAC */
+ if (port == 0)
+ reg_val = REG_RD(bp, NIG_REG_NIG_EMAC0_EN);
+ else
+ reg_val = REG_RD(bp, NIG_REG_NIG_EMAC1_EN);
+
+ /* Override the traffic led in the EMAC:*/
+ if (reg_val == 1) {
+ /* Read the current value of the LED register in
+ the EMAC block */
+ reg_val = REG_RD(bp, emac_base +
+ EMAC_REG_EMAC_LED);
+ /* Set the TRAFFIC_OVERRIDE bit to 1 */
+ reg_val |= EMAC_LED_OVERRIDE;
+ /* If value is 1, set the TRAFFIC bit, otherwise
+ reset it.*/
+ reg_val = (value == 1) ? (reg_val | EMAC_LED_TRAFFIC) :
+ (reg_val & ~EMAC_LED_TRAFFIC);
+ REG_WR(bp, emac_base + EMAC_REG_EMAC_LED, reg_val);
+ } else { /* Override the traffic led in the BMAC: */
+ REG_WR(bp, NIG_REG_LED_CONTROL_OVERRIDE_TRAFFIC_P0
+ + port*4, 1);
+ REG_WR(bp, NIG_REG_LED_CONTROL_TRAFFIC_P0 + port*4,
+ value);
+ }
+ break;
+ default:
+ DP(NETIF_MSG_LINK,
+ "bnx2x_override_led_value() unknown led index %d "
+ "(should be 0-5)\n", led_idx);
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+
+u8 bnx2x_set_led(struct link_params *params, u8 mode, u32 speed)
+{
+ u8 port = params->port;
+ u16 hw_led_mode = params->hw_led_mode;
+ u8 rc = 0;
+ u32 tmp;
+ u32 emac_base = port ? GRCBASE_EMAC1 : GRCBASE_EMAC0;
+ u32 ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config);
+ struct bnx2x *bp = params->bp;
+ DP(NETIF_MSG_LINK, "bnx2x_set_led: port %x, mode %d\n", port, mode);
+ DP(NETIF_MSG_LINK, "speed 0x%x, hw_led_mode 0x%x\n",
+ speed, hw_led_mode);
+ switch (mode) {
+ case LED_MODE_OFF:
+ REG_WR(bp, NIG_REG_LED_10G_P0 + port*4, 0);
+ REG_WR(bp, NIG_REG_LED_MODE_P0 + port*4,
+ SHARED_HW_CFG_LED_MAC1);
+
+ tmp = EMAC_RD(bp, EMAC_REG_EMAC_LED);
+ EMAC_WR(bp, EMAC_REG_EMAC_LED, (tmp | EMAC_LED_OVERRIDE));
+ break;
+
+ case LED_MODE_OPER:
+ if (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) {
+ REG_WR(bp, NIG_REG_LED_MODE_P0 + port*4, 0);
+ REG_WR(bp, NIG_REG_LED_10G_P0 + port*4, 1);
+ } else {
+ REG_WR(bp, NIG_REG_LED_MODE_P0 + port*4,
+ hw_led_mode);
+ }
+
+ REG_WR(bp, NIG_REG_LED_CONTROL_OVERRIDE_TRAFFIC_P0 +
+ port*4, 0);
+ /* Set blinking rate to ~15.9Hz */
+ REG_WR(bp, NIG_REG_LED_CONTROL_BLINK_RATE_P0 + port*4,
+ LED_BLINK_RATE_VAL);
+ REG_WR(bp, NIG_REG_LED_CONTROL_BLINK_RATE_ENA_P0 +
+ port*4, 1);
+ tmp = EMAC_RD(bp, EMAC_REG_EMAC_LED);
+ EMAC_WR(bp, EMAC_REG_EMAC_LED,
+ (tmp & (~EMAC_LED_OVERRIDE)));
+
+ if (CHIP_IS_E1(bp) &&
+ ((speed == SPEED_2500) ||
+ (speed == SPEED_1000) ||
+ (speed == SPEED_100) ||
+ (speed == SPEED_10))) {
+ /* On Everest 1 Ax chip versions for speeds less than
+ 10G LED scheme is different */
+ REG_WR(bp, NIG_REG_LED_CONTROL_OVERRIDE_TRAFFIC_P0
+ + port*4, 1);
+ REG_WR(bp, NIG_REG_LED_CONTROL_TRAFFIC_P0 +
+ port*4, 0);
+ REG_WR(bp, NIG_REG_LED_CONTROL_BLINK_TRAFFIC_P0 +
+ port*4, 1);
+ }
+ break;
+
+ default:
+ rc = -EINVAL;
+ DP(NETIF_MSG_LINK, "bnx2x_set_led: Invalid led mode %d\n",
+ mode);
+ break;
+ }
+ return rc;
+
+}
+
+u8 bnx2x_test_link(struct link_params *params, struct link_vars *vars)
+{
+ struct bnx2x *bp = params->bp;
+ u16 gp_status = 0;
+
+ CL45_RD_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_GP_STATUS,
+ MDIO_GP_STATUS_TOP_AN_STATUS1,
+ &gp_status);
+ /* link is up only if both local phy and external phy are up */
+ if ((gp_status & MDIO_GP_STATUS_TOP_AN_STATUS1_LINK_STATUS) &&
+ bnx2x_ext_phy_is_link_up(params, vars, 1))
+ return 0;
+
+ return -ESRCH;
+}
+
+static u8 bnx2x_link_initialize(struct link_params *params,
+ struct link_vars *vars)
+{
+ struct bnx2x *bp = params->bp;
+ u8 port = params->port;
+ u8 rc = 0;
+ u8 non_ext_phy;
+ u32 ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config);
+
+ /* Activate the external PHY */
+ bnx2x_ext_phy_reset(params, vars);
+
+ bnx2x_set_aer_mmd(params, vars);
+
+ if (vars->phy_flags & PHY_XGXS_FLAG)
+ bnx2x_set_master_ln(params);
+
+ rc = bnx2x_reset_unicore(params);
+ /* reset the SerDes and wait for reset bit return low */
+ if (rc != 0)
+ return rc;
+
+ bnx2x_set_aer_mmd(params, vars);
+
+ /* setting the masterLn_def again after the reset */
+ if (vars->phy_flags & PHY_XGXS_FLAG) {
+ bnx2x_set_master_ln(params);
+ bnx2x_set_swap_lanes(params);
+ }
+
+ if (vars->phy_flags & PHY_XGXS_FLAG) {
+ if ((params->req_line_speed &&
+ ((params->req_line_speed == SPEED_100) ||
+ (params->req_line_speed == SPEED_10))) ||
+ (!params->req_line_speed &&
+ (params->speed_cap_mask >=
+ PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_FULL) &&
+ (params->speed_cap_mask <
+ PORT_HW_CFG_SPEED_CAPABILITY_D0_1G)
+ )) {
+ vars->phy_flags |= PHY_SGMII_FLAG;
+ } else {
+ vars->phy_flags &= ~PHY_SGMII_FLAG;
+ }
+ }
+ /* In case of external phy existance, the line speed would be the
+ line speed linked up by the external phy. In case it is direct only,
+ then the line_speed during initialization will be equal to the
+ req_line_speed*/
+ vars->line_speed = params->req_line_speed;
+
+ bnx2x_calc_ieee_aneg_adv(params, &vars->ieee_fc);
+
+ /* init ext phy and enable link state int */
+ non_ext_phy = ((ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) ||
+ (params->loopback_mode == LOOPBACK_XGXS_10));
+
+ if (non_ext_phy ||
+ (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705) ||
+ (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706) ||
+ (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726) ||
+ (params->loopback_mode == LOOPBACK_EXT_PHY)) {
+ if (params->req_line_speed == SPEED_AUTO_NEG)
+ bnx2x_set_parallel_detection(params, vars->phy_flags);
+ bnx2x_init_internal_phy(params, vars, non_ext_phy);
+ }
+
+ if (!non_ext_phy)
+ rc |= bnx2x_ext_phy_init(params, vars);
+
+ bnx2x_bits_dis(bp, NIG_REG_STATUS_INTERRUPT_PORT0 + port*4,
+ (NIG_STATUS_XGXS0_LINK10G |
+ NIG_STATUS_XGXS0_LINK_STATUS |
+ NIG_STATUS_SERDES0_LINK_STATUS));
+
+ return rc;
+
+}
+
+
+u8 bnx2x_phy_init(struct link_params *params, struct link_vars *vars)
+{
+ struct bnx2x *bp = params->bp;
+ u32 val;
+
+ DP(NETIF_MSG_LINK, "Phy Initialization started\n");
+ DP(NETIF_MSG_LINK, "req_speed %d, req_flowctrl %d\n",
+ params->req_line_speed, params->req_flow_ctrl);
+ vars->link_status = 0;
+ vars->phy_link_up = 0;
+ vars->link_up = 0;
+ vars->line_speed = 0;
+ vars->duplex = DUPLEX_FULL;
+ vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE;
+ vars->mac_type = MAC_TYPE_NONE;
+
+ if (params->switch_cfg == SWITCH_CFG_1G)
+ vars->phy_flags = PHY_SERDES_FLAG;
+ else
+ vars->phy_flags = PHY_XGXS_FLAG;
+
+ /* disable attentions */
+ bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 + params->port*4,
+ (NIG_MASK_XGXS0_LINK_STATUS |
+ NIG_MASK_XGXS0_LINK10G |
+ NIG_MASK_SERDES0_LINK_STATUS |
+ NIG_MASK_MI_INT));
+
+ bnx2x_emac_init(params, vars);
+
+ if (CHIP_REV_IS_FPGA(bp)) {
+
+ vars->link_up = 1;
+ vars->line_speed = SPEED_10000;
+ vars->duplex = DUPLEX_FULL;
+ vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE;
+ vars->link_status = (LINK_STATUS_LINK_UP | LINK_10GTFD);
+ /* enable on E1.5 FPGA */
+ if (CHIP_IS_E1H(bp)) {
+ vars->flow_ctrl |=
+ (BNX2X_FLOW_CTRL_TX |
+ BNX2X_FLOW_CTRL_RX);
+ vars->link_status |=
+ (LINK_STATUS_TX_FLOW_CONTROL_ENABLED |
+ LINK_STATUS_RX_FLOW_CONTROL_ENABLED);
+ }
+
+ bnx2x_emac_enable(params, vars, 0);
+ bnx2x_pbf_update(params, vars->flow_ctrl, vars->line_speed);
+ /* disable drain */
+ REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 0);
+
+ /* update shared memory */
+ bnx2x_update_mng(params, vars->link_status);
+
+ return 0;
+
+ } else
+ if (CHIP_REV_IS_EMUL(bp)) {
+
+ vars->link_up = 1;
+ vars->line_speed = SPEED_10000;
+ vars->duplex = DUPLEX_FULL;
+ vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE;
+ vars->link_status = (LINK_STATUS_LINK_UP | LINK_10GTFD);
+
+ bnx2x_bmac_enable(params, vars, 0);
+
+ bnx2x_pbf_update(params, vars->flow_ctrl, vars->line_speed);
+ /* Disable drain */
+ REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE
+ + params->port*4, 0);
+
+ /* update shared memory */
+ bnx2x_update_mng(params, vars->link_status);
+
+ return 0;
+
+ } else
+ if (params->loopback_mode == LOOPBACK_BMAC) {
+
+ vars->link_up = 1;
+ vars->line_speed = SPEED_10000;
+ vars->duplex = DUPLEX_FULL;
+ vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE;
+ vars->mac_type = MAC_TYPE_BMAC;
+
+ vars->phy_flags = PHY_XGXS_FLAG;
+
+ bnx2x_phy_deassert(params, vars->phy_flags);
+ /* set bmac loopback */
+ bnx2x_bmac_enable(params, vars, 1);
+
+ REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE +
+ params->port*4, 0);
+
+ } else if (params->loopback_mode == LOOPBACK_EMAC) {
+
+ vars->link_up = 1;
+ vars->line_speed = SPEED_1000;
+ vars->duplex = DUPLEX_FULL;
+ vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE;
+ vars->mac_type = MAC_TYPE_EMAC;
+
+ vars->phy_flags = PHY_XGXS_FLAG;
+
+ bnx2x_phy_deassert(params, vars->phy_flags);
+ /* set bmac loopback */
+ bnx2x_emac_enable(params, vars, 1);
+ bnx2x_emac_program(params, vars->line_speed,
+ vars->duplex);
+ REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE +
+ params->port*4, 0);
+
+ } else if ((params->loopback_mode == LOOPBACK_XGXS_10) ||
+ (params->loopback_mode == LOOPBACK_EXT_PHY)) {
+
+ vars->link_up = 1;
+ vars->line_speed = SPEED_10000;
+ vars->duplex = DUPLEX_FULL;
+ vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE;
+
+ vars->phy_flags = PHY_XGXS_FLAG;
+
+ val = REG_RD(bp,
+ NIG_REG_XGXS0_CTRL_PHY_ADDR+
+ params->port*0x18);
+ params->phy_addr = (u8)val;
+
+ bnx2x_phy_deassert(params, vars->phy_flags);
+ bnx2x_link_initialize(params, vars);
+
+ vars->mac_type = MAC_TYPE_BMAC;
+
+ bnx2x_bmac_enable(params, vars, 0);
+
+ if (params->loopback_mode == LOOPBACK_XGXS_10) {
+ /* set 10G XGXS loopback */
+ bnx2x_set_xgxs_loopback(params, vars, 1);
+ } else {
+ /* set external phy loopback */
+ bnx2x_ext_phy_loopback(params);
+ }
+ REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE +
+ params->port*4, 0);
+
+ bnx2x_set_led(params, LED_MODE_OPER, vars->line_speed);
+ } else
+ /* No loopback */
+ {
+ bnx2x_phy_deassert(params, vars->phy_flags);
+ switch (params->switch_cfg) {
+ case SWITCH_CFG_1G:
+ vars->phy_flags |= PHY_SERDES_FLAG;
+ if ((params->ext_phy_config &
+ PORT_HW_CFG_SERDES_EXT_PHY_TYPE_MASK) ==
+ PORT_HW_CFG_SERDES_EXT_PHY_TYPE_BCM5482) {
+ vars->phy_flags |= PHY_SGMII_FLAG;
+ }
+
+ val = REG_RD(bp,
+ NIG_REG_SERDES0_CTRL_PHY_ADDR+
+ params->port*0x10);
+
+ params->phy_addr = (u8)val;
+
+ break;
+ case SWITCH_CFG_10G:
+ vars->phy_flags |= PHY_XGXS_FLAG;
+ val = REG_RD(bp,
+ NIG_REG_XGXS0_CTRL_PHY_ADDR+
+ params->port*0x18);
+ params->phy_addr = (u8)val;
+
+ break;
+ default:
+ DP(NETIF_MSG_LINK, "Invalid switch_cfg\n");
+ return -EINVAL;
+ }
+ DP(NETIF_MSG_LINK, "Phy address = 0x%x\n", params->phy_addr);
+
+ bnx2x_link_initialize(params, vars);
+ msleep(30);
+ bnx2x_link_int_enable(params);
+ }
+ return 0;
+}
+
+static void bnx2x_8726_reset_phy(struct bnx2x *bp, u8 port, u8 ext_phy_addr)
+{
+ DP(NETIF_MSG_LINK, "bnx2x_8726_reset_phy port %d\n", port);
+
+ /* Set serial boot control for external load */
+ bnx2x_cl45_write(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726, ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_GEN_CTRL, 0x0001);
+}
+
+u8 bnx2x_link_reset(struct link_params *params, struct link_vars *vars,
+ u8 reset_ext_phy)
+{
+ struct bnx2x *bp = params->bp;
+ u32 ext_phy_config = params->ext_phy_config;
+ u8 port = params->port;
+ u32 ext_phy_type = XGXS_EXT_PHY_TYPE(ext_phy_config);
+ u32 val = REG_RD(bp, params->shmem_base +
+ offsetof(struct shmem_region, dev_info.
+ port_feature_config[params->port].
+ config));
+ DP(NETIF_MSG_LINK, "Resetting the link of port %d\n", port);
+ /* disable attentions */
+ vars->link_status = 0;
+ bnx2x_update_mng(params, vars->link_status);
+ bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 + port*4,
+ (NIG_MASK_XGXS0_LINK_STATUS |
+ NIG_MASK_XGXS0_LINK10G |
+ NIG_MASK_SERDES0_LINK_STATUS |
+ NIG_MASK_MI_INT));
+
+ /* activate nig drain */
+ REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + port*4, 1);
+
+ /* disable nig egress interface */
+ REG_WR(bp, NIG_REG_BMAC0_OUT_EN + port*4, 0);
+ REG_WR(bp, NIG_REG_EGRESS_EMAC0_OUT_EN + port*4, 0);
+
+ /* Stop BigMac rx */
+ bnx2x_bmac_rx_disable(bp, port);
+
+ /* disable emac */
+ REG_WR(bp, NIG_REG_NIG_EMAC0_EN + port*4, 0);
+
+ msleep(10);
+ /* The PHY reset is controled by GPIO 1
+ * Hold it as vars low
+ */
+ /* clear link led */
+ bnx2x_set_led(params, LED_MODE_OFF, 0);
+ if (reset_ext_phy) {
+ switch (ext_phy_type) {
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT:
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072:
+ break;
+
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727:
+ {
+
+ /* Disable Transmitter */
+ u8 ext_phy_addr =
+ XGXS_EXT_PHY_ADDR(params->ext_phy_config);
+ if ((val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) ==
+ PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_DISABLE_TX_LASER)
+ bnx2x_sfp_set_transmitter(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727,
+ ext_phy_addr, 0);
+ break;
+ }
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073:
+ DP(NETIF_MSG_LINK, "Setting 8073 port %d into "
+ "low power mode\n",
+ port);
+ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
+ MISC_REGISTERS_GPIO_OUTPUT_LOW,
+ port);
+ break;
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726:
+ {
+ u8 ext_phy_addr =
+ XGXS_EXT_PHY_ADDR(params->ext_phy_config);
+ /* Set soft reset */
+ bnx2x_8726_reset_phy(bp, params->port, ext_phy_addr);
+ break;
+ }
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823:
+ {
+ u8 ext_phy_addr =
+ XGXS_EXT_PHY_ADDR(params->ext_phy_config);
+ bnx2x_cl45_write(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_CTRL, 0x0000);
+ bnx2x_cl45_write(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_CTRL, 1);
+ break;
+ }
+ default:
+ /* HW reset */
+ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
+ MISC_REGISTERS_GPIO_OUTPUT_LOW,
+ port);
+ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
+ MISC_REGISTERS_GPIO_OUTPUT_LOW,
+ port);
+ DP(NETIF_MSG_LINK, "reset external PHY\n");
+ }
+ }
+ /* reset the SerDes/XGXS */
+ REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_3_CLEAR,
+ (0x1ff << (port*16)));
+
+ /* reset BigMac */
+ REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR,
+ (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));
+
+ /* disable nig ingress interface */
+ REG_WR(bp, NIG_REG_BMAC0_IN_EN + port*4, 0);
+ REG_WR(bp, NIG_REG_EMAC0_IN_EN + port*4, 0);
+ REG_WR(bp, NIG_REG_BMAC0_OUT_EN + port*4, 0);
+ REG_WR(bp, NIG_REG_EGRESS_EMAC0_OUT_EN + port*4, 0);
+ vars->link_up = 0;
+ return 0;
+}
+
+static u8 bnx2x_update_link_down(struct link_params *params,
+ struct link_vars *vars)
+{
+ struct bnx2x *bp = params->bp;
+ u8 port = params->port;
+
+ DP(NETIF_MSG_LINK, "Port %x: Link is down\n", port);
+ bnx2x_set_led(params, LED_MODE_OFF, 0);
+
+ /* indicate no mac active */
+ vars->mac_type = MAC_TYPE_NONE;
+
+ /* update shared memory */
+ vars->link_status = 0;
+ vars->line_speed = 0;
+ bnx2x_update_mng(params, vars->link_status);
+
+ /* activate nig drain */
+ REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + port*4, 1);
+
+ /* disable emac */
+ REG_WR(bp, NIG_REG_NIG_EMAC0_EN + port*4, 0);
+
+ msleep(10);
+
+ /* reset BigMac */
+ bnx2x_bmac_rx_disable(bp, params->port);
+ REG_WR(bp, GRCBASE_MISC +
+ MISC_REGISTERS_RESET_REG_2_CLEAR,
+ (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));
+ return 0;
+}
+
+static u8 bnx2x_update_link_up(struct link_params *params,
+ struct link_vars *vars,
+ u8 link_10g, u32 gp_status)
+{
+ struct bnx2x *bp = params->bp;
+ u8 port = params->port;
+ u8 rc = 0;
+
+ vars->link_status |= LINK_STATUS_LINK_UP;
+ if (link_10g) {
+ bnx2x_bmac_enable(params, vars, 0);
+ bnx2x_set_led(params, LED_MODE_OPER, SPEED_10000);
+ } else {
+ rc = bnx2x_emac_program(params, vars->line_speed,
+ vars->duplex);
+
+ bnx2x_emac_enable(params, vars, 0);
+
+ /* AN complete? */
+ if (gp_status & MDIO_AN_CL73_OR_37_COMPLETE) {
+ if (!(vars->phy_flags &
+ PHY_SGMII_FLAG))
+ bnx2x_set_gmii_tx_driver(params);
+ }
+ }
+
+ /* PBF - link up */
+ rc |= bnx2x_pbf_update(params, vars->flow_ctrl,
+ vars->line_speed);
+
+ /* disable drain */
+ REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + port*4, 0);
+
+ /* update shared memory */
+ bnx2x_update_mng(params, vars->link_status);
+ msleep(20);
+ return rc;
+}
+/* This function should called upon link interrupt */
+/* In case vars->link_up, driver needs to
+ 1. Update the pbf
+ 2. Disable drain
+ 3. Update the shared memory
+ 4. Indicate link up
+ 5. Set LEDs
+ Otherwise,
+ 1. Update shared memory
+ 2. Reset BigMac
+ 3. Report link down
+ 4. Unset LEDs
+*/
+u8 bnx2x_link_update(struct link_params *params, struct link_vars *vars)
+{
+ struct bnx2x *bp = params->bp;
+ u8 port = params->port;
+ u16 gp_status;
+ u8 link_10g;
+ u8 ext_phy_link_up, rc = 0;
+ u32 ext_phy_type;
+ u8 is_mi_int = 0;
+
+ DP(NETIF_MSG_LINK, "port %x, XGXS?%x, int_status 0x%x\n",
+ port, (vars->phy_flags & PHY_XGXS_FLAG),
+ REG_RD(bp, NIG_REG_STATUS_INTERRUPT_PORT0 + port*4));
+
+ is_mi_int = (u8)(REG_RD(bp, NIG_REG_EMAC0_STATUS_MISC_MI_INT +
+ port*0x18) > 0);
+ DP(NETIF_MSG_LINK, "int_mask 0x%x MI_INT %x, SERDES_LINK %x\n",
+ REG_RD(bp, NIG_REG_MASK_INTERRUPT_PORT0 + port*4),
+ is_mi_int,
+ REG_RD(bp,
+ NIG_REG_SERDES0_STATUS_LINK_STATUS + port*0x3c));
+
+ DP(NETIF_MSG_LINK, " 10G %x, XGXS_LINK %x\n",
+ REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK10G + port*0x68),
+ REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK_STATUS + port*0x68));
+
+ /* disable emac */
+ REG_WR(bp, NIG_REG_NIG_EMAC0_EN + port*4, 0);
+
+ ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config);
+
+ /* Check external link change only for non-direct */
+ ext_phy_link_up = bnx2x_ext_phy_is_link_up(params, vars, is_mi_int);
+
+ /* Read gp_status */
+ CL45_RD_OVER_CL22(bp, port, params->phy_addr,
+ MDIO_REG_BANK_GP_STATUS,
+ MDIO_GP_STATUS_TOP_AN_STATUS1,
+ &gp_status);
+
+ rc = bnx2x_link_settings_status(params, vars, gp_status,
+ ext_phy_link_up);
+ if (rc != 0)
+ return rc;
+
+ /* anything 10 and over uses the bmac */
+ link_10g = ((vars->line_speed == SPEED_10000) ||
+ (vars->line_speed == SPEED_12000) ||
+ (vars->line_speed == SPEED_12500) ||
+ (vars->line_speed == SPEED_13000) ||
+ (vars->line_speed == SPEED_15000) ||
+ (vars->line_speed == SPEED_16000));
+
+ bnx2x_link_int_ack(params, vars, link_10g, is_mi_int);
+
+ /* In case external phy link is up, and internal link is down
+ ( not initialized yet probably after link initialization, it needs
+ to be initialized.
+ Note that after link down-up as result of cable plug,
+ the xgxs link would probably become up again without the need to
+ initialize it*/
+
+ if ((ext_phy_type != PORT_HW_CFG_SERDES_EXT_PHY_TYPE_DIRECT) &&
+ (ext_phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705) &&
+ (ext_phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706) &&
+ (ext_phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726) &&
+ (ext_phy_link_up && !vars->phy_link_up))
+ bnx2x_init_internal_phy(params, vars, 0);
+
+ /* link is up only if both local phy and external phy are up */
+ vars->link_up = (ext_phy_link_up && vars->phy_link_up);
+
+ if (vars->link_up)
+ rc = bnx2x_update_link_up(params, vars, link_10g, gp_status);
+ else
+ rc = bnx2x_update_link_down(params, vars);
+
+ return rc;
+}
+
+static u8 bnx2x_8073_common_init_phy(struct bnx2x *bp, u32 shmem_base)
+{
+ u8 ext_phy_addr[PORT_MAX];
+ u16 val;
+ s8 port;
+
+ /* PART1 - Reset both phys */
+ for (port = PORT_MAX - 1; port >= PORT_0; port--) {
+ /* Extract the ext phy address for the port */
+ u32 ext_phy_config = REG_RD(bp, shmem_base +
+ offsetof(struct shmem_region,
+ dev_info.port_hw_config[port].external_phy_config));
+
+ /* disable attentions */
+ bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 + port*4,
+ (NIG_MASK_XGXS0_LINK_STATUS |
+ NIG_MASK_XGXS0_LINK10G |
+ NIG_MASK_SERDES0_LINK_STATUS |
+ NIG_MASK_MI_INT));
+
+ ext_phy_addr[port] = XGXS_EXT_PHY_ADDR(ext_phy_config);
+
+ /* Need to take the phy out of low power mode in order
+ to write to access its registers */
+ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
+ MISC_REGISTERS_GPIO_OUTPUT_HIGH, port);
+
+ /* Reset the phy */
+ bnx2x_cl45_write(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073,
+ ext_phy_addr[port],
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_CTRL,
+ 1<<15);
+ }
+
+ /* Add delay of 150ms after reset */
+ msleep(150);
+
+ /* PART2 - Download firmware to both phys */
+ for (port = PORT_MAX - 1; port >= PORT_0; port--) {
+ u16 fw_ver1;
+
+ bnx2x_bcm8073_external_rom_boot(bp, port,
+ ext_phy_addr[port], shmem_base);
+
+ bnx2x_cl45_read(bp, port, PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073,
+ ext_phy_addr[port],
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_ROM_VER1, &fw_ver1);
+ if (fw_ver1 == 0 || fw_ver1 == 0x4321) {
+ DP(NETIF_MSG_LINK,
+ "bnx2x_8073_common_init_phy port %x:"
+ "Download failed. fw version = 0x%x\n",
+ port, fw_ver1);
+ return -EINVAL;
+ }
+
+ /* Only set bit 10 = 1 (Tx power down) */
+ bnx2x_cl45_read(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073,
+ ext_phy_addr[port],
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_TX_POWER_DOWN, &val);
+
+ /* Phase1 of TX_POWER_DOWN reset */
+ bnx2x_cl45_write(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073,
+ ext_phy_addr[port],
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_TX_POWER_DOWN,
+ (val | 1<<10));
+ }
+
+ /* Toggle Transmitter: Power down and then up with 600ms
+ delay between */
+ msleep(600);
+
+ /* PART3 - complete TX_POWER_DOWN process, and set GPIO2 back to low */
+ for (port = PORT_MAX - 1; port >= PORT_0; port--) {
+ /* Phase2 of POWER_DOWN_RESET */
+ /* Release bit 10 (Release Tx power down) */
+ bnx2x_cl45_read(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073,
+ ext_phy_addr[port],
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_TX_POWER_DOWN, &val);
+
+ bnx2x_cl45_write(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073,
+ ext_phy_addr[port],
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_TX_POWER_DOWN, (val & (~(1<<10))));
+ msleep(15);
+
+ /* Read modify write the SPI-ROM version select register */
+ bnx2x_cl45_read(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073,
+ ext_phy_addr[port],
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_EDC_FFE_MAIN, &val);
+ bnx2x_cl45_write(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073,
+ ext_phy_addr[port],
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_EDC_FFE_MAIN, (val | (1<<12)));
+
+ /* set GPIO2 back to LOW */
+ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
+ MISC_REGISTERS_GPIO_OUTPUT_LOW, port);
+ }
+ return 0;
+
+}
+
+static u8 bnx2x_8727_common_init_phy(struct bnx2x *bp, u32 shmem_base)
+{
+ u8 ext_phy_addr[PORT_MAX];
+ s8 port, first_port, i;
+ u32 swap_val, swap_override;
+ DP(NETIF_MSG_LINK, "Executing BCM8727 common init\n");
+ swap_val = REG_RD(bp, NIG_REG_PORT_SWAP);
+ swap_override = REG_RD(bp, NIG_REG_STRAP_OVERRIDE);
+
+ bnx2x_ext_phy_hw_reset(bp, 1 ^ (swap_val && swap_override));
+ msleep(5);
+
+ if (swap_val && swap_override)
+ first_port = PORT_0;
+ else
+ first_port = PORT_1;
+
+ /* PART1 - Reset both phys */
+ for (i = 0, port = first_port; i < PORT_MAX; i++, port = !port) {
+ /* Extract the ext phy address for the port */
+ u32 ext_phy_config = REG_RD(bp, shmem_base +
+ offsetof(struct shmem_region,
+ dev_info.port_hw_config[port].external_phy_config));
+
+ /* disable attentions */
+ bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 + port*4,
+ (NIG_MASK_XGXS0_LINK_STATUS |
+ NIG_MASK_XGXS0_LINK10G |
+ NIG_MASK_SERDES0_LINK_STATUS |
+ NIG_MASK_MI_INT));
+
+ ext_phy_addr[port] = XGXS_EXT_PHY_ADDR(ext_phy_config);
+
+ /* Reset the phy */
+ bnx2x_cl45_write(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727,
+ ext_phy_addr[port],
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_CTRL,
+ 1<<15);
+ }
+
+ /* Add delay of 150ms after reset */
+ msleep(150);
+
+ /* PART2 - Download firmware to both phys */
+ for (i = 0, port = first_port; i < PORT_MAX; i++, port = !port) {
+ u16 fw_ver1;
+
+ bnx2x_bcm8727_external_rom_boot(bp, port,
+ ext_phy_addr[port], shmem_base);
+
+ bnx2x_cl45_read(bp, port, PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727,
+ ext_phy_addr[port],
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_ROM_VER1, &fw_ver1);
+ if (fw_ver1 == 0 || fw_ver1 == 0x4321) {
+ DP(NETIF_MSG_LINK,
+ "bnx2x_8727_common_init_phy port %x:"
+ "Download failed. fw version = 0x%x\n",
+ port, fw_ver1);
+ return -EINVAL;
+ }
+ }
+
+ return 0;
+}
+
+
+static u8 bnx2x_8726_common_init_phy(struct bnx2x *bp, u32 shmem_base)
+{
+ u8 ext_phy_addr;
+ u32 val;
+ s8 port;
+
+ /* Use port1 because of the static port-swap */
+ /* Enable the module detection interrupt */
+ val = REG_RD(bp, MISC_REG_GPIO_EVENT_EN);
+ val |= ((1<<MISC_REGISTERS_GPIO_3)|
+ (1<<(MISC_REGISTERS_GPIO_3 + MISC_REGISTERS_GPIO_PORT_SHIFT)));
+ REG_WR(bp, MISC_REG_GPIO_EVENT_EN, val);
+
+ bnx2x_ext_phy_hw_reset(bp, 1);
+ msleep(5);
+ for (port = 0; port < PORT_MAX; port++) {
+ /* Extract the ext phy address for the port */
+ u32 ext_phy_config = REG_RD(bp, shmem_base +
+ offsetof(struct shmem_region,
+ dev_info.port_hw_config[port].external_phy_config));
+
+ ext_phy_addr = XGXS_EXT_PHY_ADDR(ext_phy_config);
+ DP(NETIF_MSG_LINK, "8726_common_init : ext_phy_addr = 0x%x\n",
+ ext_phy_addr);
+
+ bnx2x_8726_reset_phy(bp, port, ext_phy_addr);
+
+ /* Set fault module detected LED on */
+ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_0,
+ MISC_REGISTERS_GPIO_HIGH,
+ port);
+ }
+
+ return 0;
+}
+
+
+static u8 bnx2x_84823_common_init_phy(struct bnx2x *bp, u32 shmem_base)
+{
+ /* HW reset */
+ bnx2x_ext_phy_hw_reset(bp, 1);
+ return 0;
+}
+u8 bnx2x_common_init_phy(struct bnx2x *bp, u32 shmem_base)
+{
+ u8 rc = 0;
+ u32 ext_phy_type;
+
+ DP(NETIF_MSG_LINK, "Begin common phy init\n");
+
+ /* Read the ext_phy_type for arbitrary port(0) */
+ ext_phy_type = XGXS_EXT_PHY_TYPE(
+ REG_RD(bp, shmem_base +
+ offsetof(struct shmem_region,
+ dev_info.port_hw_config[0].external_phy_config)));
+
+ switch (ext_phy_type) {
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073:
+ {
+ rc = bnx2x_8073_common_init_phy(bp, shmem_base);
+ break;
+ }
+
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727:
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727_NOC:
+ rc = bnx2x_8727_common_init_phy(bp, shmem_base);
+ break;
+
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726:
+ /* GPIO1 affects both ports, so there's need to pull
+ it for single port alone */
+ rc = bnx2x_8726_common_init_phy(bp, shmem_base);
+ break;
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823:
+ rc = bnx2x_84823_common_init_phy(bp, shmem_base);
+ break;
+ default:
+ DP(NETIF_MSG_LINK,
+ "bnx2x_common_init_phy: ext_phy 0x%x not required\n",
+ ext_phy_type);
+ break;
+ }
+
+ return rc;
+}
+
+void bnx2x_sfx7101_sp_sw_reset(struct bnx2x *bp, u8 port, u8 phy_addr)
+{
+ u16 val, cnt;
+
+ bnx2x_cl45_read(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101,
+ phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_7101_RESET, &val);
+
+ for (cnt = 0; cnt < 10; cnt++) {
+ msleep(50);
+ /* Writes a self-clearing reset */
+ bnx2x_cl45_write(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101,
+ phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_7101_RESET,
+ (val | (1<<15)));
+ /* Wait for clear */
+ bnx2x_cl45_read(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101,
+ phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_7101_RESET, &val);
+
+ if ((val & (1<<15)) == 0)
+ break;
+ }
+}