diff options
Diffstat (limited to 'drivers/net/Kconfig')
| -rw-r--r-- | drivers/net/Kconfig | 102 |
1 files changed, 81 insertions, 21 deletions
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index c748b0e1641..6d4f9ceb0a3 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -475,6 +475,14 @@ config SGI_IOC3_ETH_HW_TX_CSUM the moment only acceleration of IPv4 is supported. This option enables offloading for checksums on transmit. If unsure, say Y. +config MIPS_SIM_NET + tristate "MIPS simulator Network device (EXPERIMENTAL)" + depends on NETDEVICES && MIPS_SIM && EXPERIMENTAL + help + The MIPSNET device is a simple Ethernet network device which is + emulated by the MIPS Simulator. + If you are not using a MIPSsim or are unsure, say N. + config SGI_O2MACE_ETH tristate "SGI O2 MACE Fast Ethernet support" depends on NET_ETHERNET && SGI_IP32=y @@ -1155,38 +1163,74 @@ config IBMVETH be called ibmveth. config IBM_EMAC - bool "IBM PPC4xx EMAC driver support" + tristate "PowerPC 4xx on-chip Ethernet support" depends on 4xx - select CRC32 - ---help--- - This driver supports the IBM PPC4xx EMAC family of on-chip - Ethernet controllers. - -config IBM_EMAC_ERRMSG - bool "Verbose error messages" - depends on IBM_EMAC && BROKEN + help + This driver supports the PowerPC 4xx EMAC family of on-chip + Ethernet controllers. config IBM_EMAC_RXB int "Number of receive buffers" depends on IBM_EMAC - default "128" if IBM_EMAC4 - default "64" + default "128" config IBM_EMAC_TXB int "Number of transmit buffers" depends on IBM_EMAC - default "128" if IBM_EMAC4 - default "8" + default "64" + +config IBM_EMAC_POLL_WEIGHT + int "MAL NAPI polling weight" + depends on IBM_EMAC + default "32" -config IBM_EMAC_FGAP - int "Frame gap" +config IBM_EMAC_RX_COPY_THRESHOLD + int "RX skb copy threshold (bytes)" depends on IBM_EMAC - default "8" + default "256" -config IBM_EMAC_SKBRES - int "Skb reserve amount" +config IBM_EMAC_RX_SKB_HEADROOM + int "Additional RX skb headroom (bytes)" depends on IBM_EMAC default "0" + help + Additional receive skb headroom. Note, that driver + will always reserve at least 2 bytes to make IP header + aligned, so usualy there is no need to add any additional + headroom. + + If unsure, set to 0. + +config IBM_EMAC_PHY_RX_CLK_FIX + bool "PHY Rx clock workaround" + depends on IBM_EMAC && (405EP || 440GX || 440EP) + help + Enable this if EMAC attached to a PHY which doesn't generate + RX clock if there is no link, if this is the case, you will + see "TX disable timeout" or "RX disable timeout" in the system + log. + + If unsure, say N. + +config IBM_EMAC_DEBUG + bool "Debugging" + depends on IBM_EMAC + default n + +config IBM_EMAC_ZMII + bool + depends on IBM_EMAC && (NP405H || NP405L || 44x) + default y + +config IBM_EMAC_RGMII + bool + depends on IBM_EMAC && 440GX + default y + +config IBM_EMAC_TAH + bool + depends on IBM_EMAC && 440GX + default y config NET_PCI bool "EISA, VLB, PCI and on board controllers" @@ -1330,7 +1374,7 @@ config FORCEDETH config CS89x0 tristate "CS89x0 support" - depends on (NET_PCI && (ISA || ARCH_IXDP2X01)) || ARCH_PNX0105 + depends on (NET_PCI && (ISA || ARCH_IXDP2X01)) || ARCH_PNX0105 || MACH_MP1000 ---help--- Support for CS89x0 chipset based Ethernet cards. If you have a network (Ethernet) card of this type, say Y and read the @@ -1767,6 +1811,7 @@ config NE_H8300 controller on the Renesas H8/300 processor. source "drivers/net/fec_8xx/Kconfig" +source "drivers/net/fs_enet/Kconfig" endmenu @@ -2083,6 +2128,7 @@ config SPIDER_NET config GIANFAR tristate "Gianfar Ethernet" depends on 85xx || 83xx + select PHYLIB help This driver supports the Gigabit TSEC on the MPC85xx family of chips, and the FEC on the 8540 @@ -2192,8 +2238,8 @@ config S2IO depends on PCI ---help--- This driver supports the 10Gbe XFrame NIC of S2IO. - For help regarding driver compilation, installation and - tuning please look into ~/drivers/net/s2io/README.txt. + More specific information on configuring the driver is in + <file:Documentation/networking/s2io.txt>. config S2IO_NAPI bool "Use Rx Polling (NAPI) (EXPERIMENTAL)" @@ -2243,6 +2289,20 @@ config ISERIES_VETH tristate "iSeries Virtual Ethernet driver support" depends on PPC_ISERIES +config RIONET + tristate "RapidIO Ethernet over messaging driver support" + depends on NETDEVICES && RAPIDIO + +config RIONET_TX_SIZE + int "Number of outbound queue entries" + depends on RIONET + default "128" + +config RIONET_RX_SIZE + int "Number of inbound queue entries" + depends on RIONET + default "128" + config FDDI bool "FDDI driver support" depends on (PCI || EISA) |