aboutsummaryrefslogtreecommitdiff
path: root/drivers/mtd/nand
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/mtd/nand')
-rw-r--r--drivers/mtd/nand/Kconfig24
-rw-r--r--drivers/mtd/nand/Makefile1
-rw-r--r--drivers/mtd/nand/atmel_nand.c11
-rw-r--r--drivers/mtd/nand/bf5xx_nand.c17
-rw-r--r--drivers/mtd/nand/davinci_nand.c342
-rw-r--r--drivers/mtd/nand/mxc_nand.c66
-rw-r--r--drivers/mtd/nand/nand_base.c3
-rw-r--r--drivers/mtd/nand/nand_ecc.c4
-rw-r--r--drivers/mtd/nand/omap2.c776
-rw-r--r--drivers/mtd/nand/orion_nand.c23
-rw-r--r--drivers/mtd/nand/plat_nand.c19
-rw-r--r--drivers/mtd/nand/s3c2410.c268
-rw-r--r--drivers/mtd/nand/txx9ndfmc.c16
13 files changed, 1406 insertions, 164 deletions
diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index f3276897859..ce96c091f01 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -74,6 +74,12 @@ config MTD_NAND_AMS_DELTA
help
Support for NAND flash on Amstrad E3 (Delta).
+config MTD_NAND_OMAP2
+ tristate "NAND Flash device on OMAP2 and OMAP3"
+ depends on ARM && MTD_NAND && (ARCH_OMAP2 || ARCH_OMAP3)
+ help
+ Support for NAND flash on Texas Instruments OMAP2 and OMAP3 platforms.
+
config MTD_NAND_TS7250
tristate "NAND Flash device on TS-7250 board"
depends on MACH_TS72XX
@@ -139,27 +145,27 @@ config MTD_NAND_PPCHAMELEONEVB
This enables the NAND flash driver on the PPChameleon EVB Board.
config MTD_NAND_S3C2410
- tristate "NAND Flash support for S3C2410/S3C2440 SoC"
- depends on ARCH_S3C2410
+ tristate "NAND Flash support for Samsung S3C SoCs"
+ depends on ARCH_S3C2410 || ARCH_S3C64XX
help
- This enables the NAND flash controller on the S3C2410 and S3C2440
+ This enables the NAND flash controller on the S3C24xx and S3C64xx
SoCs
No board specific support is done by this driver, each board
must advertise a platform_device for the driver to attach.
config MTD_NAND_S3C2410_DEBUG
- bool "S3C2410 NAND driver debug"
+ bool "Samsung S3C NAND driver debug"
depends on MTD_NAND_S3C2410
help
- Enable debugging of the S3C2410 NAND driver
+ Enable debugging of the S3C NAND driver
config MTD_NAND_S3C2410_HWECC
- bool "S3C2410 NAND Hardware ECC"
+ bool "Samsung S3C NAND Hardware ECC"
depends on MTD_NAND_S3C2410
help
- Enable the use of the S3C2410's internal ECC generator when
- using NAND. Early versions of the chip have had problems with
+ Enable the use of the controller's internal ECC generator when
+ using NAND. Early versions of the chips have had problems with
incorrect ECC generation, and if using these, the default of
software ECC is preferable.
@@ -171,7 +177,7 @@ config MTD_NAND_NDFC
NDFC Nand Flash Controllers are integrated in IBM/AMCC's 4xx SoCs
config MTD_NAND_S3C2410_CLKSTOP
- bool "S3C2410 NAND IDLE clock stop"
+ bool "Samsung S3C NAND IDLE clock stop"
depends on MTD_NAND_S3C2410
default n
help
diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile
index d33860ac42c..f3a786b3cff 100644
--- a/drivers/mtd/nand/Makefile
+++ b/drivers/mtd/nand/Makefile
@@ -25,6 +25,7 @@ obj-$(CONFIG_MTD_NAND_CS553X) += cs553x_nand.o
obj-$(CONFIG_MTD_NAND_NDFC) += ndfc.o
obj-$(CONFIG_MTD_NAND_ATMEL) += atmel_nand.o
obj-$(CONFIG_MTD_NAND_GPIO) += gpio.o
+obj-$(CONFIG_MTD_NAND_OMAP2) += omap2.o
obj-$(CONFIG_MTD_NAND_CM_X270) += cmx270_nand.o
obj-$(CONFIG_MTD_NAND_BASLER_EXCITE) += excite_nandflash.o
obj-$(CONFIG_MTD_NAND_PXA3xx) += pxa3xx_nand.o
diff --git a/drivers/mtd/nand/atmel_nand.c b/drivers/mtd/nand/atmel_nand.c
index 47a33cec379..2802992b39d 100644
--- a/drivers/mtd/nand/atmel_nand.c
+++ b/drivers/mtd/nand/atmel_nand.c
@@ -24,6 +24,7 @@
#include <linux/slab.h>
#include <linux/module.h>
+#include <linux/moduleparam.h>
#include <linux/platform_device.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/nand.h>
@@ -47,6 +48,9 @@
#define no_ecc 0
#endif
+static int on_flash_bbt = 0;
+module_param(on_flash_bbt, int, 0);
+
/* Register access macros */
#define ecc_readl(add, reg) \
__raw_readl(add + ATMEL_ECC_##reg)
@@ -459,12 +463,17 @@ static int __init atmel_nand_probe(struct platform_device *pdev)
if (host->board->det_pin) {
if (gpio_get_value(host->board->det_pin)) {
- printk("No SmartMedia card inserted.\n");
+ printk(KERN_INFO "No SmartMedia card inserted.\n");
res = ENXIO;
goto err_no_card;
}
}
+ if (on_flash_bbt) {
+ printk(KERN_INFO "atmel_nand: Use On Flash BBT\n");
+ nand_chip->options |= NAND_USE_FLASH_BBT;
+ }
+
/* first scan to find the device and get the page size */
if (nand_scan_ident(mtd, 1)) {
res = -ENXIO;
diff --git a/drivers/mtd/nand/bf5xx_nand.c b/drivers/mtd/nand/bf5xx_nand.c
index 4c2a67ca801..8506e7e606f 100644
--- a/drivers/mtd/nand/bf5xx_nand.c
+++ b/drivers/mtd/nand/bf5xx_nand.c
@@ -458,7 +458,7 @@ static irqreturn_t bf5xx_nand_dma_irq(int irq, void *dev_id)
return IRQ_HANDLED;
}
-static int bf5xx_nand_dma_rw(struct mtd_info *mtd,
+static void bf5xx_nand_dma_rw(struct mtd_info *mtd,
uint8_t *buf, int is_read)
{
struct bf5xx_nand_info *info = mtd_to_nand_info(mtd);
@@ -496,11 +496,20 @@ static int bf5xx_nand_dma_rw(struct mtd_info *mtd,
/* setup DMA register with Blackfin DMA API */
set_dma_config(CH_NFC, 0x0);
set_dma_start_addr(CH_NFC, (unsigned long) buf);
+
+/* The DMAs have different size on BF52x and BF54x */
+#ifdef CONFIG_BF52x
+ set_dma_x_count(CH_NFC, (page_size >> 1));
+ set_dma_x_modify(CH_NFC, 2);
+ val = DI_EN | WDSIZE_16;
+#endif
+
+#ifdef CONFIG_BF54x
set_dma_x_count(CH_NFC, (page_size >> 2));
set_dma_x_modify(CH_NFC, 4);
-
- /* setup write or read operation */
val = DI_EN | WDSIZE_32;
+#endif
+ /* setup write or read operation */
if (is_read)
val |= WNR;
set_dma_config(CH_NFC, val);
@@ -512,8 +521,6 @@ static int bf5xx_nand_dma_rw(struct mtd_info *mtd,
else
bfin_write_NFC_PGCTL(0x2);
wait_for_completion(&info->dma_completion);
-
- return 0;
}
static void bf5xx_nand_dma_read_buf(struct mtd_info *mtd,
diff --git a/drivers/mtd/nand/davinci_nand.c b/drivers/mtd/nand/davinci_nand.c
index 02700f769b8..0fad6487e6f 100644
--- a/drivers/mtd/nand/davinci_nand.c
+++ b/drivers/mtd/nand/davinci_nand.c
@@ -44,7 +44,7 @@
* and some flavors of secondary chipselect (e.g. based on A12) as used
* with multichip packages.
*
- * The 1-bit ECC hardware is supported, but not yet the newer 4-bit ECC
+ * The 1-bit ECC hardware is supported, as well as the newer 4-bit ECC
* available on chips like the DM355 and OMAP-L137 and needed with the
* more error-prone MLC NAND chips.
*
@@ -54,11 +54,14 @@
struct davinci_nand_info {
struct mtd_info mtd;
struct nand_chip chip;
+ struct nand_ecclayout ecclayout;
struct device *dev;
struct clk *clk;
bool partitioned;
+ bool is_readmode;
+
void __iomem *base;
void __iomem *vaddr;
@@ -73,6 +76,7 @@ struct davinci_nand_info {
};
static DEFINE_SPINLOCK(davinci_nand_lock);
+static bool ecc4_busy;
#define to_davinci_nand(m) container_of(m, struct davinci_nand_info, mtd)
@@ -218,6 +222,192 @@ static int nand_davinci_correct_1bit(struct mtd_info *mtd, u_char *dat,
/*----------------------------------------------------------------------*/
/*
+ * 4-bit hardware ECC ... context maintained over entire AEMIF
+ *
+ * This is a syndrome engine, but we avoid NAND_ECC_HW_SYNDROME
+ * since that forces use of a problematic "infix OOB" layout.
+ * Among other things, it trashes manufacturer bad block markers.
+ * Also, and specific to this hardware, it ECC-protects the "prepad"
+ * in the OOB ... while having ECC protection for parts of OOB would
+ * seem useful, the current MTD stack sometimes wants to update the
+ * OOB without recomputing ECC.
+ */
+
+static void nand_davinci_hwctl_4bit(struct mtd_info *mtd, int mode)
+{
+ struct davinci_nand_info *info = to_davinci_nand(mtd);
+ unsigned long flags;
+ u32 val;
+
+ spin_lock_irqsave(&davinci_nand_lock, flags);
+
+ /* Start 4-bit ECC calculation for read/write */
+ val = davinci_nand_readl(info, NANDFCR_OFFSET);
+ val &= ~(0x03 << 4);
+ val |= (info->core_chipsel << 4) | BIT(12);
+ davinci_nand_writel(info, NANDFCR_OFFSET, val);
+
+ info->is_readmode = (mode == NAND_ECC_READ);
+
+ spin_unlock_irqrestore(&davinci_nand_lock, flags);
+}
+
+/* Read raw ECC code after writing to NAND. */
+static void
+nand_davinci_readecc_4bit(struct davinci_nand_info *info, u32 code[4])
+{
+ const u32 mask = 0x03ff03ff;
+
+ code[0] = davinci_nand_readl(info, NAND_4BIT_ECC1_OFFSET) & mask;
+ code[1] = davinci_nand_readl(info, NAND_4BIT_ECC2_OFFSET) & mask;
+ code[2] = davinci_nand_readl(info, NAND_4BIT_ECC3_OFFSET) & mask;
+ code[3] = davinci_nand_readl(info, NAND_4BIT_ECC4_OFFSET) & mask;
+}
+
+/* Terminate read ECC; or return ECC (as bytes) of data written to NAND. */
+static int nand_davinci_calculate_4bit(struct mtd_info *mtd,
+ const u_char *dat, u_char *ecc_code)
+{
+ struct davinci_nand_info *info = to_davinci_nand(mtd);
+ u32 raw_ecc[4], *p;
+ unsigned i;
+
+ /* After a read, terminate ECC calculation by a dummy read
+ * of some 4-bit ECC register. ECC covers everything that
+ * was read; correct() just uses the hardware state, so
+ * ecc_code is not needed.
+ */
+ if (info->is_readmode) {
+ davinci_nand_readl(info, NAND_4BIT_ECC1_OFFSET);
+ return 0;
+ }
+
+ /* Pack eight raw 10-bit ecc values into ten bytes, making
+ * two passes which each convert four values (in upper and
+ * lower halves of two 32-bit words) into five bytes. The
+ * ROM boot loader uses this same packing scheme.
+ */
+ nand_davinci_readecc_4bit(info, raw_ecc);
+ for (i = 0, p = raw_ecc; i < 2; i++, p += 2) {
+ *ecc_code++ = p[0] & 0xff;
+ *ecc_code++ = ((p[0] >> 8) & 0x03) | ((p[0] >> 14) & 0xfc);
+ *ecc_code++ = ((p[0] >> 22) & 0x0f) | ((p[1] << 4) & 0xf0);
+ *ecc_code++ = ((p[1] >> 4) & 0x3f) | ((p[1] >> 10) & 0xc0);
+ *ecc_code++ = (p[1] >> 18) & 0xff;
+ }
+
+ return 0;
+}
+
+/* Correct up to 4 bits in data we just read, using state left in the
+ * hardware plus the ecc_code computed when it was first written.
+ */
+static int nand_davinci_correct_4bit(struct mtd_info *mtd,
+ u_char *data, u_char *ecc_code, u_char *null)
+{
+ int i;
+ struct davinci_nand_info *info = to_davinci_nand(mtd);
+ unsigned short ecc10[8];
+ unsigned short *ecc16;
+ u32 syndrome[4];
+ unsigned num_errors, corrected;
+
+ /* All bytes 0xff? It's an erased page; ignore its ECC. */
+ for (i = 0; i < 10; i++) {
+ if (ecc_code[i] != 0xff)
+ goto compare;
+ }
+ return 0;
+
+compare:
+ /* Unpack ten bytes into eight 10 bit values. We know we're
+ * little-endian, and use type punning for less shifting/masking.
+ */
+ if (WARN_ON(0x01 & (unsigned) ecc_code))
+ return -EINVAL;
+ ecc16 = (unsigned short *)ecc_code;
+
+ ecc10[0] = (ecc16[0] >> 0) & 0x3ff;
+ ecc10[1] = ((ecc16[0] >> 10) & 0x3f) | ((ecc16[1] << 6) & 0x3c0);
+ ecc10[2] = (ecc16[1] >> 4) & 0x3ff;
+ ecc10[3] = ((ecc16[1] >> 14) & 0x3) | ((ecc16[2] << 2) & 0x3fc);
+ ecc10[4] = (ecc16[2] >> 8) | ((ecc16[3] << 8) & 0x300);
+ ecc10[5] = (ecc16[3] >> 2) & 0x3ff;
+ ecc10[6] = ((ecc16[3] >> 12) & 0xf) | ((ecc16[4] << 4) & 0x3f0);
+ ecc10[7] = (ecc16[4] >> 6) & 0x3ff;
+
+ /* Tell ECC controller about the expected ECC codes. */
+ for (i = 7; i >= 0; i--)
+ davinci_nand_writel(info, NAND_4BIT_ECC_LOAD_OFFSET, ecc10[i]);
+
+ /* Allow time for syndrome calculation ... then read it.
+ * A syndrome of all zeroes 0 means no detected errors.
+ */
+ davinci_nand_readl(info, NANDFSR_OFFSET);
+ nand_davinci_readecc_4bit(info, syndrome);
+ if (!(syndrome[0] | syndrome[1] | syndrome[2] | syndrome[3]))
+ return 0;
+
+ /* Start address calculation, and wait for it to complete.
+ * We _could_ start reading more data while this is working,
+ * to speed up the overall page read.
+ */
+ davinci_nand_writel(info, NANDFCR_OFFSET,
+ davinci_nand_readl(info, NANDFCR_OFFSET) | BIT(13));
+ for (;;) {
+ u32 fsr = davinci_nand_readl(info, NANDFSR_OFFSET);
+
+ switch ((fsr >> 8) & 0x0f) {
+ case 0: /* no error, should not happen */
+ return 0;
+ case 1: /* five or more errors detected */
+ return -EIO;
+ case 2: /* error addresses computed */
+ case 3:
+ num_errors = 1 + ((fsr >> 16) & 0x03);
+ goto correct;
+ default: /* still working on it */
+ cpu_relax();
+ continue;
+ }
+ }
+
+correct:
+ /* correct each error */
+ for (i = 0, corrected = 0; i < num_errors; i++) {
+ int error_address, error_value;
+
+ if (i > 1) {
+ error_address = davinci_nand_readl(info,
+ NAND_ERR_ADD2_OFFSET);
+ error_value = davinci_nand_readl(info,
+ NAND_ERR_ERRVAL2_OFFSET);
+ } else {
+ error_address = davinci_nand_readl(info,
+ NAND_ERR_ADD1_OFFSET);
+ error_value = davinci_nand_readl(info,
+ NAND_ERR_ERRVAL1_OFFSET);
+ }
+
+ if (i & 1) {
+ error_address >>= 16;
+ error_value >>= 16;
+ }
+ error_address &= 0x3ff;
+ error_address = (512 + 7) - error_address;
+
+ if (error_address < 512) {
+ data[error_address] ^= error_value;
+ corrected++;
+ }
+ }
+
+ return corrected;
+}
+
+/*----------------------------------------------------------------------*/
+
+/*
* NOTE: NAND boot requires ALE == EM_A[1], CLE == EM_A[2], so that's
* how these chips are normally wired. This translates to both 8 and 16
* bit busses using ALE == BIT(3) in byte addresses, and CLE == BIT(4).
@@ -294,6 +484,23 @@ static void __init nand_dm6446evm_flash_init(struct davinci_nand_info *info)
/*----------------------------------------------------------------------*/
+/* An ECC layout for using 4-bit ECC with small-page flash, storing
+ * ten ECC bytes plus the manufacturer's bad block marker byte, and
+ * and not overlapping the default BBT markers.
+ */
+static struct nand_ecclayout hwecc4_small __initconst = {
+ .eccbytes = 10,
+ .eccpos = { 0, 1, 2, 3, 4,
+ /* offset 5 holds the badblock marker */
+ 6, 7,
+ 13, 14, 15, },
+ .oobfree = {
+ {.offset = 8, .length = 5, },
+ {.offset = 16, },
+ },
+};
+
+
static int __init nand_davinci_probe(struct platform_device *pdev)
{
struct davinci_nand_pdata *pdata = pdev->dev.platform_data;
@@ -306,6 +513,10 @@ static int __init nand_davinci_probe(struct platform_device *pdev)
uint32_t val;
nand_ecc_modes_t ecc_mode;
+ /* insist on board-specific configuration */
+ if (!pdata)
+ return -ENODEV;
+
/* which external chipselect will we be managing? */
if (pdev->id < 0 || pdev->id > 3)
return -ENODEV;
@@ -351,7 +562,7 @@ static int __init nand_davinci_probe(struct platform_device *pdev)
info->chip.select_chip = nand_davinci_select_chip;
/* options such as NAND_USE_FLASH_BBT or 16-bit widths */
- info->chip.options = pdata ? pdata->options : 0;
+ info->chip.options = pdata->options;
info->ioaddr = (uint32_t __force) vaddr;
@@ -360,14 +571,8 @@ static int __init nand_davinci_probe(struct platform_device *pdev)
info->mask_chipsel = pdata->mask_chipsel;
/* use nandboot-capable ALE/CLE masks by default */
- if (pdata && pdata->mask_ale)
- info->mask_ale = pdata->mask_cle;
- else
- info->mask_ale = MASK_ALE;
- if (pdata && pdata->mask_cle)
- info->mask_cle = pdata->mask_cle;
- else
- info->mask_cle = MASK_CLE;
+ info->mask_ale = pdata->mask_cle ? : MASK_ALE;
+ info->mask_cle = pdata->mask_cle ? : MASK_CLE;
/* Set address of hardware control function */
info->chip.cmd_ctrl = nand_davinci_hwcontrol;
@@ -377,30 +582,44 @@ static int __init nand_davinci_probe(struct platform_device *pdev)
info->chip.read_buf = nand_davinci_read_buf;
info->chip.write_buf = nand_davinci_write_buf;
- /* use board-specific ECC config; else, the best available */
- if (pdata)
- ecc_mode = pdata->ecc_mode;
- else
- ecc_mode = NAND_ECC_HW;
+ /* Use board-specific ECC config */
+ ecc_mode = pdata->ecc_mode;
+ ret = -EINVAL;
switch (ecc_mode) {
case NAND_ECC_NONE:
case NAND_ECC_SOFT:
+ pdata->ecc_bits = 0;
break;
case NAND_ECC_HW:
- info->chip.ecc.calculate = nand_davinci_calculate_1bit;
- info->chip.ecc.correct = nand_davinci_correct_1bit;
- info->chip.ecc.hwctl = nand_davinci_hwctl_1bit;
+ if (pdata->ecc_bits == 4) {
+ /* No sanity checks: CPUs must support this,
+ * and the chips may not use NAND_BUSWIDTH_16.
+ */
+
+ /* No sharing 4-bit hardware between chipselects yet */
+ spin_lock_irq(&davinci_nand_lock);
+ if (ecc4_busy)
+ ret = -EBUSY;
+ else
+ ecc4_busy = true;
+ spin_unlock_irq(&davinci_nand_lock);
+
+ if (ret == -EBUSY)
+ goto err_ecc;
+
+ info->chip.ecc.calculate = nand_davinci_calculate_4bit;
+ info->chip.ecc.correct = nand_davinci_correct_4bit;
+ info->chip.ecc.hwctl = nand_davinci_hwctl_4bit;
+ info->chip.ecc.bytes = 10;
+ } else {
+ info->chip.ecc.calculate = nand_davinci_calculate_1bit;
+ info->chip.ecc.correct = nand_davinci_correct_1bit;
+ info->chip.ecc.hwctl = nand_davinci_hwctl_1bit;
+ info->chip.ecc.bytes = 3;
+ }
info->chip.ecc.size = 512;
- info->chip.ecc.bytes = 3;
break;
- case NAND_ECC_HW_SYNDROME:
- /* FIXME implement */
- info->chip.ecc.size = 512;
- info->chip.ecc.bytes = 10;
-
- dev_warn(&pdev->dev, "4-bit ECC nyet supported\n");
- /* FALL THROUGH */
default:
ret = -EINVAL;
goto err_ecc;
@@ -441,12 +660,56 @@ static int __init nand_davinci_probe(struct platform_device *pdev)
spin_unlock_irq(&davinci_nand_lock);
/* Scan to find existence of the device(s) */
- ret = nand_scan(&info->mtd, pdata->mask_chipsel ? 2 : 1);
+ ret = nand_scan_ident(&info->mtd, pdata->mask_chipsel ? 2 : 1);
if (ret < 0) {
dev_dbg(&pdev->dev, "no NAND chip(s) found\n");
goto err_scan;
}
+ /* Update ECC layout if needed ... for 1-bit HW ECC, the default
+ * is OK, but it allocates 6 bytes when only 3 are needed (for
+ * each 512 bytes). For the 4-bit HW ECC, that default is not
+ * usable: 10 bytes are needed, not 6.
+ */
+ if (pdata->ecc_bits == 4) {
+ int chunks = info->mtd.writesize / 512;
+
+ if (!chunks || info->mtd.oobsize < 16) {
+ dev_dbg(&pdev->dev, "too small\n");
+ ret = -EINVAL;
+ goto err_scan;
+ }
+
+ /* For small page chips, preserve the manufacturer's
+ * badblock marking data ... and make sure a flash BBT
+ * table marker fits in the free bytes.
+ */
+ if (chunks == 1) {
+ info->ecclayout = hwecc4_small;
+ info->ecclayout.oobfree[1].length =
+ info->mtd.oobsize - 16;
+ goto syndrome_done;
+ }
+
+ /* For large page chips we'll be wanting to use a
+ * not-yet-implemented mode that reads OOB data
+ * before reading the body of the page, to avoid
+ * the "infix OOB" model of NAND_ECC_HW_SYNDROME
+ * (and preserve manufacturer badblock markings).
+ */
+ dev_warn(&pdev->dev, "no 4-bit ECC support yet "
+ "for large page NAND\n");
+ ret = -EIO;
+ goto err_scan;
+
+syndrome_done:
+ info->chip.ecc.layout = &info->ecclayout;
+ }
+
+ ret = nand_scan_tail(&info->mtd);
+ if (ret < 0)
+ goto err_scan;
+
if (mtd_has_partitions()) {
struct mtd_partition *mtd_parts = NULL;
int mtd_parts_nb = 0;
@@ -455,22 +718,11 @@ static int __init nand_davinci_probe(struct platform_device *pdev)
static const char *probes[] __initconst =
{ "cmdlinepart", NULL };
- const char *master_name;
-
- /* Set info->mtd.name = 0 temporarily */
- master_name = info->mtd.name;
- info->mtd.name = (char *)0;
-
- /* info->mtd.name == 0, means: don't bother checking
- <mtd-id> */
mtd_parts_nb = parse_mtd_partitions(&info->mtd, probes,
&mtd_parts, 0);
-
- /* Restore info->mtd.name */
- info->mtd.name = master_name;
}
- if (mtd_parts_nb <= 0 && pdata) {
+ if (mtd_parts_nb <= 0) {
mtd_parts = pdata->parts;
mtd_parts_nb = pdata->nr_parts;
}
@@ -483,7 +735,7 @@ static int __init nand_davinci_probe(struct platform_device *pdev)
info->partitioned = true;
}
- } else if (pdata && pdata->nr_parts) {
+ } else if (pdata->nr_parts) {
dev_warn(&pdev->dev, "ignoring %d default partitions on %s\n",
pdata->nr_parts, info->mtd.name);
}
@@ -509,6 +761,11 @@ err_scan:
err_clk_enable:
clk_put(info->clk);
+ spin_lock_irq(&davinci_nand_lock);
+ if (ecc_mode == NAND_ECC_HW_SYNDROME)
+ ecc4_busy = false;
+ spin_unlock_irq(&davinci_nand_lock);
+
err_ecc:
err_clk:
err_ioremap:
@@ -532,6 +789,11 @@ static int __exit nand_davinci_remove(struct platform_device *pdev)
else
status = del_mtd_device(&info->mtd);
+ spin_lock_irq(&davinci_nand_lock);
+ if (info->chip.ecc.mode == NAND_ECC_HW_SYNDROME)
+ ecc4_busy = false;
+ spin_unlock_irq(&davinci_nand_lock);
+
iounmap(info->base);
iounmap(info->vaddr);
diff --git a/drivers/mtd/nand/mxc_nand.c b/drivers/mtd/nand/mxc_nand.c
index 40c26080ecd..76beea40d2c 100644
--- a/drivers/mtd/nand/mxc_nand.c
+++ b/drivers/mtd/nand/mxc_nand.c
@@ -138,7 +138,14 @@ static struct nand_ecclayout nand_hw_eccoob_8 = {
static struct nand_ecclayout nand_hw_eccoob_16 = {
.eccbytes = 5,
.eccpos = {6, 7, 8, 9, 10},
- .oobfree = {{0, 6}, {12, 4}, }
+ .oobfree = {{0, 5}, {11, 5}, }
+};
+
+static struct nand_ecclayout nand_hw_eccoob_64 = {
+ .eccbytes = 20,
+ .eccpos = {6, 7, 8, 9, 10, 22, 23, 24, 25, 26,
+ 38, 39, 40, 41, 42, 54, 55, 56, 57, 58},
+ .oobfree = {{2, 4}, {11, 10}, {27, 10}, {43, 10}, {59, 5}, }
};
#ifdef CONFIG_MTD_PARTITIONS
@@ -192,7 +199,7 @@ static void wait_op_done(struct mxc_nand_host *host, int max_retries,
}
udelay(1);
}
- if (max_retries <= 0)
+ if (max_retries < 0)
DEBUG(MTD_DEBUG_LEVEL0, "%s(%d): INT not set\n",
__func__, param);
}
@@ -795,9 +802,13 @@ static void mxc_nand_command(struct mtd_info *mtd, unsigned command,
send_addr(host, (page_addr & 0xff), false);
if (host->pagesize_2k) {
- send_addr(host, (page_addr >> 8) & 0xFF, false);
- if (mtd->size >= 0x40000000)
+ if (mtd->size >= 0x10000000) {
+ /* paddr_8 - paddr_15 */
+ send_addr(host, (page_addr >> 8) & 0xff, false);
send_addr(host, (page_addr >> 16) & 0xff, true);
+ } else
+ /* paddr_8 - paddr_15 */
+ send_addr(host, (page_addr >> 8) & 0xff, true);
} else {
/* One more address cycle for higher density devices */
if (mtd->size >= 0x4000000) {
@@ -923,7 +934,6 @@ static int __init mxcnd_probe(struct platform_device *pdev)
this->ecc.mode = NAND_ECC_HW;
this->ecc.size = 512;
this->ecc.bytes = 3;
- this->ecc.layout = &nand_hw_eccoob_8;
tmp = readw(host->regs + NFC_CONFIG1);
tmp |= NFC_ECC_EN;
writew(tmp, host->regs + NFC_CONFIG1);
@@ -957,12 +967,44 @@ static int __init mxcnd_probe(struct platform_device *pdev)
this->ecc.layout = &nand_hw_eccoob_16;
}
- host->pagesize_2k = 0;
+ /* first scan to find the device and get the page size */
+ if (nand_scan_ident(mtd, 1)) {
+ err = -ENXIO;
+ goto escan;
+ }
- /* Scan to find existence of the device */
- if (nand_scan(mtd, 1)) {
- DEBUG(MTD_DEBUG_LEVEL0,
- "MXC_ND: Unable to find any NAND device.\n");
+ host->pagesize_2k = (mtd->writesize == 2048) ? 1 : 0;
+
+ if (this->ecc.mode == NAND_ECC_HW) {
+ switch (mtd->oobsize) {
+ case 8:
+ this->ecc.layout = &nand_hw_eccoob_8;
+ break;
+ case 16:
+ this->ecc.layout = &nand_hw_eccoob_16;
+ break;
+ case 64:
+ this->ecc.layout = &nand_hw_eccoob_64;
+ break;
+ default:
+ /* page size not handled by HW ECC */
+ /* switching back to soft ECC */
+ this->ecc.size = 512;
+ this->ecc.bytes = 3;
+ this->ecc.layout = &nand_hw_eccoob_8;
+ this->ecc.mode = NAND_ECC_SOFT;
+ this->ecc.calculate = NULL;
+ this->ecc.correct = NULL;
+ this->ecc.hwctl = NULL;
+ tmp = readw(host->regs + NFC_CONFIG1);
+ tmp &= ~NFC_ECC_EN;
+ writew(tmp, host->regs + NFC_CONFIG1);
+ break;
+ }
+ }
+
+ /* second phase scan */
+ if (nand_scan_tail(mtd)) {
err = -ENXIO;
goto escan;
}
@@ -985,7 +1027,7 @@ static int __init mxcnd_probe(struct platform_device *pdev)
return 0;
escan:
- free_irq(host->irq, NULL);
+ free_irq(host->irq, host);
eirq:
iounmap(host->regs);
eres:
@@ -1005,7 +1047,7 @@ static int __devexit mxcnd_remove(struct platform_device *pdev)
platform_set_drvdata(pdev, NULL);
nand_release(&host->mtd);
- free_irq(host->irq, NULL);
+ free_irq(host->irq, host);
iounmap(host->regs);
kfree(host);
diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c
index 3d7ed432fa4..8c21b89d2d0 100644
--- a/drivers/mtd/nand/nand_base.c
+++ b/drivers/mtd/nand/nand_base.c
@@ -2756,7 +2756,8 @@ int nand_scan_tail(struct mtd_info *mtd)
* the out of band area
*/
chip->ecc.layout->oobavail = 0;
- for (i = 0; chip->ecc.layout->oobfree[i].length; i++)
+ for (i = 0; chip->ecc.layout->oobfree[i].length
+ && i < ARRAY_SIZE(chip->ecc.layout->oobfree); i++)
chip->ecc.layout->oobavail +=
chip->ecc.layout->oobfree[i].length;
mtd->oobavail = chip->ecc.layout->oobavail;
diff --git a/drivers/mtd/nand/nand_ecc.c b/drivers/mtd/nand/nand_ecc.c
index 868147acce2..c0cb87d6d16 100644
--- a/drivers/mtd/nand/nand_ecc.c
+++ b/drivers/mtd/nand/nand_ecc.c
@@ -428,8 +428,8 @@ EXPORT_SYMBOL(nand_calculate_ecc);
int nand_correct_data(struct mtd_info *mtd, unsigned char *buf,
unsigned char *read_ecc, unsigned char *calc_ecc)
{
- unsigned char b0, b1, b2;
- unsigned char byte_addr, bit_addr;
+ unsigned char b0, b1, b2, bit_addr;
+ unsigned int byte_addr;
/* 256 or 512 bytes/ecc */
const uint32_t eccsize_mult =
(((struct nand_chip *)mtd->priv)->ecc.size) >> 8;
diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c
new file mode 100644
index 00000000000..0cd76f89f4b
--- /dev/null
+++ b/drivers/mtd/nand/omap2.c
@@ -0,0 +1,776 @@
+/*
+ * Copyright © 2004 Texas Instruments, Jian Zhang <jzhang@ti.com>
+ * Copyright © 2004 Micron Technology Inc.
+ * Copyright © 2004 David Brownell
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/platform_device.h>
+#include <linux/dma-mapping.h>
+#include <linux/delay.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/partitions.h>
+#include <linux/io.h>
+
+#include <asm/dma.h>
+
+#include <mach/gpmc.h>
+#include <mach/nand.h>
+
+#define GPMC_IRQ_STATUS 0x18
+#define GPMC_ECC_CONFIG 0x1F4
+#define GPMC_ECC_CONTROL 0x1F8
+#define GPMC_ECC_SIZE_CONFIG 0x1FC
+#define GPMC_ECC1_RESULT 0x200
+
+#define DRIVER_NAME "omap2-nand"
+
+/* size (4 KiB) for IO mapping */
+#define NAND_IO_SIZE SZ_4K
+
+#define NAND_WP_OFF 0
+#define NAND_WP_BIT 0x00000010
+#define WR_RD_PIN_MONITORING 0x00600000
+
+#define GPMC_BUF_FULL 0x00000001
+#define GPMC_BUF_EMPTY 0x00000000
+
+#define NAND_Ecc_P1e (1 << 0)
+#define NAND_Ecc_P2e (1 << 1)
+#define NAND_Ecc_P4e (1 << 2)
+#define NAND_Ecc_P8e (1 << 3)
+#define NAND_Ecc_P16e (1 << 4)
+#define NAND_Ecc_P32e (1 << 5)
+#define NAND_Ecc_P64e (1 << 6)
+#define NAND_Ecc_P128e (1 << 7)
+#define NAND_Ecc_P256e (1 << 8)
+#define NAND_Ecc_P512e (1 << 9)
+#define NAND_Ecc_P1024e (1 << 10)
+#define NAND_Ecc_P2048e (1 << 11)
+
+#define NAND_Ecc_P1o (1 << 16)
+#define NAND_Ecc_P2o (1 << 17)
+#define NAND_Ecc_P4o (1 << 18)
+#define NAND_Ecc_P8o (1 << 19)
+#define NAND_Ecc_P16o (1 << 20)
+#define NAND_Ecc_P32o (1 << 21)
+#define NAND_Ecc_P64o (1 << 22)
+#define NAND_Ecc_P128o (1 << 23)
+#define NAND_Ecc_P256o (1 << 24)
+#define NAND_Ecc_P512o (1 << 25)
+#define NAND_Ecc_P1024o (1 << 26)
+#define NAND_Ecc_P2048o (1 << 27)
+
+#define TF(value) (value ? 1 : 0)
+
+#define P2048e(a) (TF(a & NAND_Ecc_P2048e) << 0)
+#define P2048o(a) (TF(a & NAND_Ecc_P2048o) << 1)
+#define P1e(a) (TF(a & NAND_Ecc_P1e) << 2)
+#define P1o(a) (TF(a & NAND_Ecc_P1o) << 3)
+#define P2e(a) (TF(a & NAND_Ecc_P2e) << 4)
+#define P2o(a) (TF(a & NAND_Ecc_P2o) << 5)
+#define P4e(a) (TF(a & NAND_Ecc_P4e) << 6)
+#define P4o(a) (TF(a & NAND_Ecc_P4o) << 7)
+
+#define P8e(a) (TF(a & NAND_Ecc_P8e) << 0)
+#define P8o(a) (TF(a & NAND_Ecc_P8o) << 1)
+#define P16e(a) (TF(a & NAND_Ecc_P16e) << 2)
+#define P16o(a) (TF(a & NAND_Ecc_P16o) << 3)
+#define P32e(a) (TF(a & NAND_Ecc_P32e) << 4)
+#define P32o(a) (TF(a & NAND_Ecc_P32o) << 5)
+#define P64e(a) (TF(a & NAND_Ecc_P64e) << 6)
+#define P64o(a) (TF(a & NAND_Ecc_P64o) << 7)
+
+#define P128e(a) (TF(a & NAND_Ecc_P128e) << 0)
+#define P128o(a) (TF(a & NAND_Ecc_P128o) << 1)
+#define P256e(a) (TF(a & NAND_Ecc_P256e) << 2)
+#define P256o(a) (TF(a & NAND_Ecc_P256o) << 3)
+#define P512e(a) (TF(a & NAND_Ecc_P512e) << 4)
+#define P512o(a) (TF(a & NAND_Ecc_P512o) << 5)
+#define P1024e(a) (TF(a & NAND_Ecc_P1024e) << 6)
+#define P1024o(a) (TF(a & NAND_Ecc_P1024o) << 7)
+
+#define P8e_s(a) (TF(a & NAND_Ecc_P8e) << 0)
+#define P8o_s(a) (TF(a & NAND_Ecc_P8o) << 1)
+#define P16e_s(a) (TF(a & NAND_Ecc_P16e) << 2)
+#define P16o_s(a) (TF(a & NAND_Ecc_P16o) << 3)
+#define P1e_s(a) (TF(a & NAND_Ecc_P1e) << 4)
+#define P1o_s(a) (TF(a & NAND_Ecc_P1o) << 5)
+#define P2e_s(a) (TF(a & NAND_Ecc_P2e) << 6)
+#define P2o_s(a) (TF(a & NAND_Ecc_P2o) << 7)
+
+#define P4e_s(a) (TF(a & NAND_Ecc_P4e) << 0)
+#define P4o_s(a) (TF(a & NAND_Ecc_P4o) << 1)
+
+#ifdef CONFIG_MTD_PARTITIONS
+static const char *part_probes[] = { "cmdlinepart", NULL };
+#endif
+
+struct omap_nand_info {
+ struct nand_hw_control controller;
+ struct omap_nand_platform_data *pdata;
+ struct mtd_info mtd;
+ struct mtd_partition *parts;
+ struct nand_chip nand;
+ struct platform_device *pdev;
+
+ int gpmc_cs;
+ unsigned long phys_base;
+ void __iomem *gpmc_cs_baseaddr;
+ void __iomem *gpmc_baseaddr;
+};
+
+/**
+ * omap_nand_wp - This function enable or disable the Write Protect feature
+ * @mtd: MTD device structure
+ * @mode: WP ON/OFF
+ */
+static void omap_nand_wp(struct mtd_info *mtd, int mode)
+{
+ struct omap_nand_info *info = container_of(mtd,
+ struct omap_nand_info, mtd);
+
+ unsigned long config = __raw_readl(info->gpmc_baseaddr + GPMC_CONFIG);
+
+ if (mode)
+ config &= ~(NAND_WP_BIT); /* WP is ON */
+ else
+ config |= (NAND_WP_BIT); /* WP is OFF */
+
+ __raw_writel(config, (info->gpmc_baseaddr + GPMC_CONFIG));
+}
+
+/**
+ * omap_hwcontrol - hardware specific access to control-lines
+ * @mtd: MTD device structure
+ * @cmd: command to device
+ * @ctrl:
+ * NAND_NCE: bit 0 -> don't care
+ * NAND_CLE: bit 1 -> Command Latch
+ * NAND_ALE: bit 2 -> Address Latch
+ *
+ * NOTE: boards may use different bits for these!!
+ */
+static void omap_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl)
+{
+ struct omap_nand_info *info = container_of(mtd,
+ struct omap_nand_info, mtd);
+ switch (ctrl) {
+ case NAND_CTRL_CHANGE | NAND_CTRL_CLE:
+ info->nand.IO_ADDR_W = info->gpmc_cs_baseaddr +
+ GPMC_CS_NAND_COMMAND;
+ info->nand.IO_ADDR_R = info->gpmc_cs_baseaddr +
+ GPMC_CS_NAND_DATA;
+ break;
+
+ case NAND_CTRL_CHANGE | NAND_CTRL_ALE:
+ info->nand.IO_ADDR_W = info->gpmc_cs_baseaddr +
+ GPMC_CS_NAND_ADDRESS;
+ info->nand.IO_ADDR_R = info->gpmc_cs_baseaddr +
+ GPMC_CS_NAND_DATA;
+ break;
+
+ case NAND_CTRL_CHANGE | NAND_NCE:
+ info->nand.IO_ADDR_W = info->gpmc_cs_baseaddr +
+ GPMC_CS_NAND_DATA;
+ info->nand.IO_ADDR_R = info->gpmc_cs_baseaddr +
+ GPMC_CS_NAND_DATA;
+ break;
+ }
+
+ if (cmd != NAND_CMD_NONE)
+ __raw_writeb(cmd, info->nand.IO_ADDR_W);
+}
+
+/**
+ * omap_read_buf16 - read data from NAND controller into buffer
+ * @mtd: MTD device structure
+ * @buf: