diff options
Diffstat (limited to 'drivers/mtd/nand/denali.c')
| -rw-r--r-- | drivers/mtd/nand/denali.c | 25 |
1 files changed, 13 insertions, 12 deletions
diff --git a/drivers/mtd/nand/denali.c b/drivers/mtd/nand/denali.c index f59dd03f36d..3ba89525cf0 100644 --- a/drivers/mtd/nand/denali.c +++ b/drivers/mtd/nand/denali.c @@ -56,7 +56,7 @@ MODULE_PARM_DESC(onfi_timing_mode, "Overrides default ONFI setting." INTR_STATUS0__ERASE_COMP) /* indicates whether or not the internal value for the flash bank is - valid or not */ + * valid or not */ #define CHIP_SELECT_INVALID -1 #define SUPPORT_8BITECC 1 @@ -71,7 +71,7 @@ MODULE_PARM_DESC(onfi_timing_mode, "Overrides default ONFI setting." #define mtd_to_denali(m) container_of(m, struct denali_nand_info, mtd) /* These constants are defined by the driver to enable common driver - configuration options. */ + * configuration options. */ #define SPARE_ACCESS 0x41 #define MAIN_ACCESS 0x42 #define MAIN_SPARE_ACCESS 0x43 @@ -97,7 +97,7 @@ static const struct pci_device_id denali_pci_ids[] = { /* these are static lookup tables that give us easy access to - registers in the NAND controller. + * registers in the NAND controller. */ static const uint32_t intr_status_addresses[4] = {INTR_STATUS0, INTR_STATUS1, @@ -429,7 +429,7 @@ static void get_hynix_nand_para(struct denali_nand_info *denali, } /* determines how many NAND chips are connected to the controller. Note for - Intel CE4100 devices we don't support more than one device. + * Intel CE4100 devices we don't support more than one device. */ static void find_valid_banks(struct denali_nand_info *denali) { @@ -572,7 +572,7 @@ static void denali_set_intr_modes(struct denali_nand_info *denali, } /* validation function to verify that the controlling software is making - a valid request + * a valid request */ static inline bool is_flash_bank_valid(int flash_bank) { @@ -726,7 +726,7 @@ static uint32_t wait_for_irq(struct denali_nand_info *denali, uint32_t irq_mask) } /* This helper function setups the registers for ECC and whether or not - the spare area will be transfered. */ + * the spare area will be transfered. */ static void setup_ecc_for_xfer(struct denali_nand_info *denali, bool ecc_en, bool transfer_spare) { @@ -743,7 +743,7 @@ static void setup_ecc_for_xfer(struct denali_nand_info *denali, bool ecc_en, } /* sends a pipeline command operation to the controller. See the Denali NAND - controller's user guide for more information (section 4.2.3.6). + * controller's user guide for more information (section 4.2.3.6). */ static int denali_send_pipeline_cmd(struct denali_nand_info *denali, bool ecc_en, @@ -1042,7 +1042,7 @@ static void denali_setup_dma(struct denali_nand_info *denali, int op) } /* writes a page. user specifies type, and this function handles the - configuration details. */ + * configuration details. */ static void write_page(struct mtd_info *mtd, struct nand_chip *chip, const uint8_t *buf, bool raw_xfer) { @@ -1099,8 +1099,9 @@ static void write_page(struct mtd_info *mtd, struct nand_chip *chip, /* NAND core entry points */ /* this is the callback that the NAND core calls to write a page. Since - writing a page with ECC or without is similar, all the work is done - by write_page above. */ + * writing a page with ECC or without is similar, all the work is done + * by write_page above. + * */ static void denali_write_page(struct mtd_info *mtd, struct nand_chip *chip, const uint8_t *buf) { @@ -1110,8 +1111,8 @@ static void denali_write_page(struct mtd_info *mtd, struct nand_chip *chip, } /* This is the callback that the NAND core calls to write a page without ECC. - raw access is similiar to ECC page writes, so all the work is done in the - write_page() function above. + * raw access is similiar to ECC page writes, so all the work is done in the + * write_page() function above. */ static void denali_write_page_raw(struct mtd_info *mtd, struct nand_chip *chip, const uint8_t *buf) |