1 files changed, 302 insertions, 40 deletions

diff --git a/drivers/mtd/nand/davinci_nand.c b/drivers/mtd/nand/davinci_nand.c
index 02700f769b8..0fad6487e6f 100644
--- a/drivers/mtd/nand/davinci_nand.c
+++ b/drivers/mtd/nand/davinci_nand.c
@@ -44,7 +44,7 @@
  * and some flavors of secondary chipselect (e.g. based on A12) as used
  * with multichip packages.
  *
- * The 1-bit ECC hardware is supported, but not yet the newer 4-bit ECC
+ * The 1-bit ECC hardware is supported, as well as the newer 4-bit ECC
  * available on chips like the DM355 and OMAP-L137 and needed with the
  * more error-prone MLC NAND chips.
  *
@@ -54,11 +54,14 @@
 struct davinci_nand_info {
 	struct mtd_info		mtd;
 	struct nand_chip	chip;
+	struct nand_ecclayout	ecclayout;
 
 	struct device		*dev;
 	struct clk		*clk;
 	bool			partitioned;
 
+	bool			is_readmode;
+
 	void __iomem		*base;
 	void __iomem		*vaddr;
 
@@ -73,6 +76,7 @@ struct davinci_nand_info {
 };
 
 static DEFINE_SPINLOCK(davinci_nand_lock);
+static bool ecc4_busy;
 
 #define to_davinci_nand(m) container_of(m, struct davinci_nand_info, mtd)
 
@@ -218,6 +222,192 @@ static int nand_davinci_correct_1bit(struct mtd_info *mtd, u_char *dat,
 /*----------------------------------------------------------------------*/
 
 /*
+ * 4-bit hardware ECC ... context maintained over entire AEMIF
+ *
+ * This is a syndrome engine, but we avoid NAND_ECC_HW_SYNDROME
+ * since that forces use of a problematic "infix OOB" layout.
+ * Among other things, it trashes manufacturer bad block markers.
+ * Also, and specific to this hardware, it ECC-protects the "prepad"
+ * in the OOB ... while having ECC protection for parts of OOB would
+ * seem useful, the current MTD stack sometimes wants to update the
+ * OOB without recomputing ECC.
+ */
+
+static void nand_davinci_hwctl_4bit(struct mtd_info *mtd, int mode)
+{
+	struct davinci_nand_info *info = to_davinci_nand(mtd);
+	unsigned long flags;
+	u32 val;
+
+	spin_lock_irqsave(&davinci_nand_lock, flags);
+
+	/* Start 4-bit ECC calculation for read/write */
+	val = davinci_nand_readl(info, NANDFCR_OFFSET);
+	val &= ~(0x03 << 4);
+	val |= (info->core_chipsel << 4) | BIT(12);
+	davinci_nand_writel(info, NANDFCR_OFFSET, val);
+
+	info->is_readmode = (mode == NAND_ECC_READ);
+
+	spin_unlock_irqrestore(&davinci_nand_lock, flags);
+}
+
+/* Read raw ECC code after writing to NAND. */
+static void
+nand_davinci_readecc_4bit(struct davinci_nand_info *info, u32 code[4])
+{
+	const u32 mask = 0x03ff03ff;
+
+	code[0] = davinci_nand_readl(info, NAND_4BIT_ECC1_OFFSET) & mask;
+	code[1] = davinci_nand_readl(info, NAND_4BIT_ECC2_OFFSET) & mask;
+	code[2] = davinci_nand_readl(info, NAND_4BIT_ECC3_OFFSET) & mask;
+	code[3] = davinci_nand_readl(info, NAND_4BIT_ECC4_OFFSET) & mask;
+}
+
+/* Terminate read ECC; or return ECC (as bytes) of data written to NAND. */
+static int nand_davinci_calculate_4bit(struct mtd_info *mtd,
+		const u_char *dat, u_char *ecc_code)
+{
+	struct davinci_nand_info *info = to_davinci_nand(mtd);
+	u32 raw_ecc[4], *p;
+	unsigned i;
+
+	/* After a read, terminate ECC calculation by a dummy read
+	 * of some 4-bit ECC register.  ECC covers everything that
+	 * was read; correct() just uses the hardware state, so
+	 * ecc_code is not needed.
+	 */
+	if (info->is_readmode) {
+		davinci_nand_readl(info, NAND_4BIT_ECC1_OFFSET);
+		return 0;
+	}
+
+	/* Pack eight raw 10-bit ecc values into ten bytes, making
+	 * two passes which each convert four values (in upper and
+	 * lower halves of two 32-bit words) into five bytes.  The
+	 * ROM boot loader uses this same packing scheme.
+	 */
+	nand_davinci_readecc_4bit(info, raw_ecc);
+	for (i = 0, p = raw_ecc; i < 2; i++, p += 2) {
+		*ecc_code++ =   p[0]        & 0xff;
+		*ecc_code++ = ((p[0] >>  8) & 0x03) | ((p[0] >> 14) & 0xfc);
+		*ecc_code++ = ((p[0] >> 22) & 0x0f) | ((p[1] <<  4) & 0xf0);
+		*ecc_code++ = ((p[1] >>  4) & 0x3f) | ((p[1] >> 10) & 0xc0);
+		*ecc_code++ =  (p[1] >> 18) & 0xff;
+	}
+
+	return 0;
+}
+
+/* Correct up to 4 bits in data we just read, using state left in the
+ * hardware plus the ecc_code computed when it was first written.
+ */
+static int nand_davinci_correct_4bit(struct mtd_info *mtd,
+		u_char *data, u_char *ecc_code, u_char *null)
+{
+	int i;
+	struct davinci_nand_info *info = to_davinci_nand(mtd);
+	unsigned short ecc10[8];
+	unsigned short *ecc16;
+	u32 syndrome[4];
+	unsigned num_errors, corrected;
+
+	/* All bytes 0xff?  It's an erased page; ignore its ECC. */
+	for (i = 0; i < 10; i++) {
+		if (ecc_code[i] != 0xff)
+			goto compare;
+	}
+	return 0;
+
+compare:
+	/* Unpack ten bytes into eight 10 bit values.  We know we're
+	 * little-endian, and use type punning for less shifting/masking.
+	 */
+	if (WARN_ON(0x01 & (unsigned) ecc_code))
+		return -EINVAL;
+	ecc16 = (unsigned short *)ecc_code;
+
+	ecc10[0] =  (ecc16[0] >>  0) & 0x3ff;
+	ecc10[1] = ((ecc16[0] >> 10) & 0x3f) | ((ecc16[1] << 6) & 0x3c0);
+	ecc10[2] =  (ecc16[1] >>  4) & 0x3ff;
+	ecc10[3] = ((ecc16[1] >> 14) & 0x3)  | ((ecc16[2] << 2) & 0x3fc);
+	ecc10[4] =  (ecc16[2] >>  8)         | ((ecc16[3] << 8) & 0x300);
+	ecc10[5] =  (ecc16[3] >>  2) & 0x3ff;
+	ecc10[6] = ((ecc16[3] >> 12) & 0xf)  | ((ecc16[4] << 4) & 0x3f0);
+	ecc10[7] =  (ecc16[4] >>  6) & 0x3ff;
+
+	/* Tell ECC controller about the expected ECC codes. */
+	for (i = 7; i >= 0; i--)
+		davinci_nand_writel(info, NAND_4BIT_ECC_LOAD_OFFSET, ecc10[i]);
+
+	/* Allow time for syndrome calculation ... then read it.
+	 * A syndrome of all zeroes 0 means no detected errors.
+	 */
+	davinci_nand_readl(info, NANDFSR_OFFSET);
+	nand_davinci_readecc_4bit(info, syndrome);
+	if (!(syndrome[0] | syndrome[1] | syndrome[2] | syndrome[3]))
+		return 0;
+
+	/* Start address calculation, and wait for it to complete.
+	 * We _could_ start reading more data while this is working,
+	 * to speed up the overall page read.
+	 */
+	davinci_nand_writel(info, NANDFCR_OFFSET,
+			davinci_nand_readl(info, NANDFCR_OFFSET) | BIT(13));
+	for (;;) {
+		u32	fsr = davinci_nand_readl(info, NANDFSR_OFFSET);
+
+		switch ((fsr >> 8) & 0x0f) {
+		case 0:		/* no error, should not happen */
+			return 0;
+		case 1:		/* five or more errors detected */
+			return -EIO;
+		case 2:		/* error addresses computed */
+		case 3:
+			num_errors = 1 + ((fsr >> 16) & 0x03);
+			goto correct;
+		default:	/* still working on it */
+			cpu_relax();
+			continue;
+		}
+	}
+
+correct:
+	/* correct each error */
+	for (i = 0, corrected = 0; i < num_errors; i++) {
+		int error_address, error_value;
+
+		if (i > 1) {
+			error_address = davinci_nand_readl(info,
+						NAND_ERR_ADD2_OFFSET);
+			error_value = davinci_nand_readl(info,
+						NAND_ERR_ERRVAL2_OFFSET);
+		} else {
+			error_address = davinci_nand_readl(info,
+						NAND_ERR_ADD1_OFFSET);
+			error_value = davinci_nand_readl(info,
+						NAND_ERR_ERRVAL1_OFFSET);
+		}
+
+		if (i & 1) {
+			error_address >>= 16;
+			error_value >>= 16;
+		}
+		error_address &= 0x3ff;
+		error_address = (512 + 7) - error_address;
+
+		if (error_address < 512) {
+			data[error_address] ^= error_value;
+			corrected++;
+		}
+	}
+
+	return corrected;
+}
+
+/*----------------------------------------------------------------------*/
+
+/*
  * NOTE:  NAND boot requires ALE == EM_A[1], CLE == EM_A[2], so that's
  * how these chips are normally wired.  This translates to both 8 and 16
  * bit busses using ALE == BIT(3) in byte addresses, and CLE == BIT(4).
@@ -294,6 +484,23 @@ static void __init nand_dm6446evm_flash_init(struct davinci_nand_info *info)
 
 /*----------------------------------------------------------------------*/
 
+/* An ECC layout for using 4-bit ECC with small-page flash, storing
+ * ten ECC bytes plus the manufacturer's bad block marker byte, and
+ * and not overlapping the default BBT markers.
+ */
+static struct nand_ecclayout hwecc4_small __initconst = {
+	.eccbytes = 10,
+	.eccpos = { 0, 1, 2, 3, 4,
+		/* offset 5 holds the badblock marker */
+		6, 7,
+		13, 14, 15, },
+	.oobfree = {
+		{.offset = 8, .length = 5, },
+		{.offset = 16, },
+	},
+};
+
+
 static int __init nand_davinci_probe(struct platform_device *pdev)
 {
 	struct davinci_nand_pdata	*pdata = pdev->dev.platform_data;
@@ -306,6 +513,10 @@ static int __init nand_davinci_probe(struct platform_device *pdev)
 	uint32_t			val;
 	nand_ecc_modes_t		ecc_mode;
 
+	/* insist on board-specific configuration */
+	if (!pdata)
+		return -ENODEV;
+
 	/* which external chipselect will we be managing? */
 	if (pdev->id < 0 || pdev->id > 3)
 		return -ENODEV;
@@ -351,7 +562,7 @@ static int __init nand_davinci_probe(struct platform_device *pdev)
 	info->chip.select_chip	= nand_davinci_select_chip;
 
 	/* options such as NAND_USE_FLASH_BBT or 16-bit widths */
-	info->chip.options	= pdata ? pdata->options : 0;
+	info->chip.options	= pdata->options;
 
 	info->ioaddr		= (uint32_t __force) vaddr;
 
@@ -360,14 +571,8 @@ static int __init nand_davinci_probe(struct platform_device *pdev)
 	info->mask_chipsel	= pdata->mask_chipsel;
 
 	/* use nandboot-capable ALE/CLE masks by default */
-	if (pdata && pdata->mask_ale)
-		info->mask_ale	= pdata->mask_cle;
-	else
-		info->mask_ale	= MASK_ALE;
-	if (pdata && pdata->mask_cle)
-		info->mask_cle	= pdata->mask_cle;
-	else
-		info->mask_cle	= MASK_CLE;
+	info->mask_ale		= pdata->mask_cle ? : MASK_ALE;
+	info->mask_cle		= pdata->mask_cle ? : MASK_CLE;
 
 	/* Set address of hardware control function */
 	info->chip.cmd_ctrl	= nand_davinci_hwcontrol;
@@ -377,30 +582,44 @@ static int __init nand_davinci_probe(struct platform_device *pdev)
 	info->chip.read_buf     = nand_davinci_read_buf;
 	info->chip.write_buf    = nand_davinci_write_buf;
 
-	/* use board-specific ECC config; else, the best available */
-	if (pdata)
-		ecc_mode = pdata->ecc_mode;
-	else
-		ecc_mode = NAND_ECC_HW;
+	/* Use board-specific ECC config */
+	ecc_mode		= pdata->ecc_mode;
 
+	ret = -EINVAL;
 	switch (ecc_mode) {
 	case NAND_ECC_NONE:
 	case NAND_ECC_SOFT:
+		pdata->ecc_bits = 0;
 		break;
 	case NAND_ECC_HW:
-		info->chip.ecc.calculate = nand_davinci_calculate_1bit;
-		info->chip.ecc.correct = nand_davinci_correct_1bit;
-		info->chip.ecc.hwctl = nand_davinci_hwctl_1bit;
+		if (pdata->ecc_bits == 4) {
+			/* No sanity checks:  CPUs must support this,
+			 * and the chips may not use NAND_BUSWIDTH_16.
+			 */
+
+			/* No sharing 4-bit hardware between chipselects yet */
+			spin_lock_irq(&davinci_nand_lock);
+			if (ecc4_busy)
+				ret = -EBUSY;
+			else
+				ecc4_busy = true;
+			spin_unlock_irq(&davinci_nand_lock);
+
+			if (ret == -EBUSY)
+				goto err_ecc;
+
+			info->chip.ecc.calculate = nand_davinci_calculate_4bit;
+			info->chip.ecc.correct = nand_davinci_correct_4bit;
+			info->chip.ecc.hwctl = nand_davinci_hwctl_4bit;
+			info->chip.ecc.bytes = 10;
+		} else {
+			info->chip.ecc.calculate = nand_davinci_calculate_1bit;
+			info->chip.ecc.correct = nand_davinci_correct_1bit;
+			info->chip.ecc.hwctl = nand_davinci_hwctl_1bit;
+			info->chip.ecc.bytes = 3;
+		}
 		info->chip.ecc.size = 512;
-		info->chip.ecc.bytes = 3;
 		break;
-	case NAND_ECC_HW_SYNDROME:
-		/* FIXME implement */
-		info->chip.ecc.size = 512;
-		info->chip.ecc.bytes = 10;
-
-		dev_warn(&pdev->dev, "4-bit ECC nyet supported\n");
-		/* FALL THROUGH */
 	default:
 		ret = -EINVAL;
 		goto err_ecc;
@@ -441,12 +660,56 @@ static int __init nand_davinci_probe(struct platform_device *pdev)
 	spin_unlock_irq(&davinci_nand_lock);
 
 	/* Scan to find existence of the device(s) */
-	ret = nand_scan(&info->mtd, pdata->mask_chipsel ? 2 : 1);
+	ret = nand_scan_ident(&info->mtd, pdata->mask_chipsel ? 2 : 1);
 	if (ret < 0) {
 		dev_dbg(&pdev->dev, "no NAND chip(s) found\n");
 		goto err_scan;
 	}
 
+	/* Update ECC layout if needed ... for 1-bit HW ECC, the default
+	 * is OK, but it allocates 6 bytes when only 3 are needed (for
+	 * each 512 bytes).  For the 4-bit HW ECC, that default is not
+	 * usable:  10 bytes are needed, not 6.
+	 */
+	if (pdata->ecc_bits == 4) {
+		int	chunks = info->mtd.writesize / 512;
+
+		if (!chunks || info->mtd.oobsize < 16) {
+			dev_dbg(&pdev->dev, "too small\n");
+			ret = -EINVAL;
+			goto err_scan;
+		}
+
+		/* For small page chips, preserve the manufacturer's
+		 * badblock marking data ... and make sure a flash BBT
+		 * table marker fits in the free bytes.
+		 */
+		if (chunks == 1) {
+			info->ecclayout = hwecc4_small;
+			info->ecclayout.oobfree[1].length =
+				info->mtd.oobsize - 16;
+			goto syndrome_done;
+		}
+
+		/* For large page chips we'll be wanting to use a
+		 * not-yet-implemented mode that reads OOB data
+		 * before reading the body of the page, to avoid
+		 * the "infix OOB" model of NAND_ECC_HW_SYNDROME
+		 * (and preserve manufacturer badblock markings).
+		 */
+		dev_warn(&pdev->dev, "no 4-bit ECC support yet "
+				"for large page NAND\n");
+		ret = -EIO;
+		goto err_scan;
+
+syndrome_done:
+		info->chip.ecc.layout = &info->ecclayout;
+	}
+
+	ret = nand_scan_tail(&info->mtd);
+	if (ret < 0)
+		goto err_scan;
+
 	if (mtd_has_partitions()) {
 		struct mtd_partition	*mtd_parts = NULL;
 		int			mtd_parts_nb = 0;
@@ -455,22 +718,11 @@ static int __init nand_davinci_probe(struct platform_device *pdev)
 			static const char *probes[] __initconst =
 				{ "cmdlinepart", NULL };
 
-			const char		*master_name;
-
-			/* Set info->mtd.name = 0 temporarily */
-			master_name		= info->mtd.name;
-			info->mtd.name		= (char *)0;
-
-			/* info->mtd.name == 0, means: don't bother checking
-			   <mtd-id> */
 			mtd_parts_nb = parse_mtd_partitions(&info->mtd, probes,
 							    &mtd_parts, 0);
-
-			/* Restore info->mtd.name */
-			info->mtd.name = master_name;
 		}
 
-		if (mtd_parts_nb <= 0 && pdata) {
+		if (mtd_parts_nb <= 0) {
 			mtd_parts = pdata->parts;
 			mtd_parts_nb = pdata->nr_parts;
 		}
@@ -483,7 +735,7 @@ static int __init nand_davinci_probe(struct platform_device *pdev)
 				info->partitioned = true;
 		}
 
-	} else if (pdata && pdata->nr_parts) {
+	} else if (pdata->nr_parts) {
 		dev_warn(&pdev->dev, "ignoring %d default partitions on %s\n",
 				pdata->nr_parts, info->mtd.name);
 	}
@@ -509,6 +761,11 @@ err_scan:
 err_clk_enable:
 	clk_put(info->clk);
 
+	spin_lock_irq(&davinci_nand_lock);
+	if (ecc_mode == NAND_ECC_HW_SYNDROME)
+		ecc4_busy = false;
+	spin_unlock_irq(&davinci_nand_lock);
+
 err_ecc:
 err_clk:
 err_ioremap:
@@ -532,6 +789,11 @@ static int __exit nand_davinci_remove(struct platform_device *pdev)
 	else
 		status = del_mtd_device(&info->mtd);
 
+	spin_lock_irq(&davinci_nand_lock);
+	if (info->chip.ecc.mode == NAND_ECC_HW_SYNDROME)
+		ecc4_busy = false;
+	spin_unlock_irq(&davinci_nand_lock);
+
 	iounmap(info->base);
 	iounmap(info->vaddr);