diff options
Diffstat (limited to 'drivers/mtd/devices')
| -rw-r--r-- | drivers/mtd/devices/Kconfig | 10 | ||||
| -rw-r--r-- | drivers/mtd/devices/Makefile | 1 | ||||
| -rw-r--r-- | drivers/mtd/devices/block2mtd.c | 19 | ||||
| -rw-r--r-- | drivers/mtd/devices/docg3.c | 4 | ||||
| -rw-r--r-- | drivers/mtd/devices/elm.c | 89 | ||||
| -rw-r--r-- | drivers/mtd/devices/m25p80.c | 1292 | ||||
| -rw-r--r-- | drivers/mtd/devices/mtd_dataflash.c | 24 | ||||
| -rw-r--r-- | drivers/mtd/devices/phram.c | 41 | ||||
| -rw-r--r-- | drivers/mtd/devices/pmc551.c | 7 | ||||
| -rw-r--r-- | drivers/mtd/devices/serial_flash_cmds.h | 61 | ||||
| -rw-r--r-- | drivers/mtd/devices/slram.c | 4 | ||||
| -rw-r--r-- | drivers/mtd/devices/spear_smi.c | 6 | ||||
| -rw-r--r-- | drivers/mtd/devices/sst25l.c | 1 | ||||
| -rw-r--r-- | drivers/mtd/devices/st_spi_fsm.c | 2080 |
14 files changed, 2399 insertions, 1240 deletions
diff --git a/drivers/mtd/devices/Kconfig b/drivers/mtd/devices/Kconfig index 01281382180..c49d0b127fe 100644 --- a/drivers/mtd/devices/Kconfig +++ b/drivers/mtd/devices/Kconfig @@ -80,7 +80,7 @@ config MTD_DATAFLASH_OTP config MTD_M25P80 tristate "Support most SPI Flash chips (AT26DF, M25P, W25X, ...)" - depends on SPI_MASTER + depends on SPI_MASTER && MTD_SPI_NOR help This enables access to most modern SPI flash chips, used for program and data storage. Series supported include Atmel AT26DF, @@ -210,6 +210,14 @@ config MTD_DOCG3 M-Systems and now Sandisk. The support is very experimental, and doesn't give access to any write operations. +config MTD_ST_SPI_FSM + tristate "ST Microelectronics SPI FSM Serial Flash Controller" + depends on ARCH_STI + help + This provides an MTD device driver for the ST Microelectronics + SPI Fast Sequence Mode (FSM) Serial Flash Controller and support + for a subset of connected Serial Flash devices. + if MTD_DOCG3 config BCH_CONST_M default 14 diff --git a/drivers/mtd/devices/Makefile b/drivers/mtd/devices/Makefile index d83bd73096f..c68868f6058 100644 --- a/drivers/mtd/devices/Makefile +++ b/drivers/mtd/devices/Makefile @@ -16,6 +16,7 @@ obj-$(CONFIG_MTD_NAND_OMAP_BCH) += elm.o obj-$(CONFIG_MTD_SPEAR_SMI) += spear_smi.o obj-$(CONFIG_MTD_SST25L) += sst25l.o obj-$(CONFIG_MTD_BCM47XXSFLASH) += bcm47xxsflash.o +obj-$(CONFIG_MTD_ST_SPI_FSM) += st_spi_fsm.o CFLAGS_docg3.o += -I$(src) diff --git a/drivers/mtd/devices/block2mtd.c b/drivers/mtd/devices/block2mtd.c index d9fd87a4c8d..66f0405f7e5 100644 --- a/drivers/mtd/devices/block2mtd.c +++ b/drivers/mtd/devices/block2mtd.c @@ -209,7 +209,6 @@ static void block2mtd_free_device(struct block2mtd_dev *dev) } -/* FIXME: ensure that mtd->size % erase_size == 0 */ static struct block2mtd_dev *add_device(char *devname, int erase_size) { const fmode_t mode = FMODE_READ | FMODE_WRITE | FMODE_EXCL; @@ -240,13 +239,18 @@ static struct block2mtd_dev *add_device(char *devname, int erase_size) if (IS_ERR(bdev)) { pr_err("error: cannot open device %s\n", devname); - goto devinit_err; + goto err_free_block2mtd; } dev->blkdev = bdev; if (MAJOR(bdev->bd_dev) == MTD_BLOCK_MAJOR) { pr_err("attempting to use an MTD device as a block device\n"); - goto devinit_err; + goto err_free_block2mtd; + } + + if ((long)dev->blkdev->bd_inode->i_size % erase_size) { + pr_err("erasesize must be a divisor of device size\n"); + goto err_free_block2mtd; } mutex_init(&dev->write_mutex); @@ -255,7 +259,7 @@ static struct block2mtd_dev *add_device(char *devname, int erase_size) /* make the name contain the block device in */ name = kasprintf(GFP_KERNEL, "block2mtd: %s", devname); if (!name) - goto devinit_err; + goto err_destroy_mutex; dev->mtd.name = name; @@ -274,7 +278,7 @@ static struct block2mtd_dev *add_device(char *devname, int erase_size) if (mtd_device_register(&dev->mtd, NULL, 0)) { /* Device didn't get added, so free the entry */ - goto devinit_err; + goto err_destroy_mutex; } list_add(&dev->list, &blkmtd_device_list); pr_info("mtd%d: [%s] erase_size = %dKiB [%d]\n", @@ -283,7 +287,9 @@ static struct block2mtd_dev *add_device(char *devname, int erase_size) dev->mtd.erasesize >> 10, dev->mtd.erasesize); return dev; -devinit_err: +err_destroy_mutex: + mutex_destroy(&dev->write_mutex); +err_free_block2mtd: block2mtd_free_device(dev); return NULL; } @@ -448,6 +454,7 @@ static void block2mtd_exit(void) struct block2mtd_dev *dev = list_entry(pos, typeof(*dev), list); block2mtd_sync(&dev->mtd); mtd_device_unregister(&dev->mtd); + mutex_destroy(&dev->write_mutex); pr_info("mtd%d: [%s] removed\n", dev->mtd.index, dev->mtd.name + strlen("block2mtd: ")); diff --git a/drivers/mtd/devices/docg3.c b/drivers/mtd/devices/docg3.c index dd5e1018d37..91a169c44b3 100644 --- a/drivers/mtd/devices/docg3.c +++ b/drivers/mtd/devices/docg3.c @@ -1608,8 +1608,8 @@ static ssize_t dps1_insert_key(struct device *dev, #define FLOOR_SYSFS(id) { \ __ATTR(f##id##_dps0_is_keylocked, S_IRUGO, dps0_is_key_locked, NULL), \ __ATTR(f##id##_dps1_is_keylocked, S_IRUGO, dps1_is_key_locked, NULL), \ - __ATTR(f##id##_dps0_protection_key, S_IWUGO, NULL, dps0_insert_key), \ - __ATTR(f##id##_dps1_protection_key, S_IWUGO, NULL, dps1_insert_key), \ + __ATTR(f##id##_dps0_protection_key, S_IWUSR|S_IWGRP, NULL, dps0_insert_key), \ + __ATTR(f##id##_dps1_protection_key, S_IWUSR|S_IWGRP, NULL, dps1_insert_key), \ } static struct device_attribute doc_sys_attrs[DOC_MAX_NBFLOORS][4] = { diff --git a/drivers/mtd/devices/elm.c b/drivers/mtd/devices/elm.c index d1dd6a33a05..b4f61c7fc16 100644 --- a/drivers/mtd/devices/elm.c +++ b/drivers/mtd/devices/elm.c @@ -15,6 +15,8 @@ * */ +#define DRIVER_NAME "omap-elm" + #include <linux/platform_device.h> #include <linux/module.h> #include <linux/interrupt.h> @@ -84,6 +86,8 @@ struct elm_info { struct list_head list; enum bch_ecc bch_type; struct elm_registers elm_regs; + int ecc_steps; + int ecc_syndrome_size; }; static LIST_HEAD(elm_devices); @@ -103,7 +107,8 @@ static u32 elm_read_reg(struct elm_info *info, int offset) * @dev: ELM device * @bch_type: Type of BCH ecc */ -int elm_config(struct device *dev, enum bch_ecc bch_type) +int elm_config(struct device *dev, enum bch_ecc bch_type, + int ecc_steps, int ecc_step_size, int ecc_syndrome_size) { u32 reg_val; struct elm_info *info = dev_get_drvdata(dev); @@ -112,10 +117,22 @@ int elm_config(struct device *dev, enum bch_ecc bch_type) dev_err(dev, "Unable to configure elm - device not probed?\n"); return -ENODEV; } + /* ELM cannot detect ECC errors for chunks > 1KB */ + if (ecc_step_size > ((ELM_ECC_SIZE + 1) / 2)) { + dev_err(dev, "unsupported config ecc-size=%d\n", ecc_step_size); + return -EINVAL; + } + /* ELM support 8 error syndrome process */ + if (ecc_steps > ERROR_VECTOR_MAX) { + dev_err(dev, "unsupported config ecc-step=%d\n", ecc_steps); + return -EINVAL; + } reg_val = (bch_type & ECC_BCH_LEVEL_MASK) | (ELM_ECC_SIZE << 16); elm_write_reg(info, ELM_LOCATION_CONFIG, reg_val); - info->bch_type = bch_type; + info->bch_type = bch_type; + info->ecc_steps = ecc_steps; + info->ecc_syndrome_size = ecc_syndrome_size; return 0; } @@ -157,17 +174,15 @@ static void elm_load_syndrome(struct elm_info *info, int i, offset; u32 val; - for (i = 0; i < ERROR_VECTOR_MAX; i++) { + for (i = 0; i < info->ecc_steps; i++) { /* Check error reported */ if (err_vec[i].error_reported) { elm_configure_page_mode(info, i, true); offset = ELM_SYNDROME_FRAGMENT_0 + SYNDROME_FRAGMENT_REG_SIZE * i; - - /* BCH8 */ - if (info->bch_type) { - + switch (info->bch_type) { + case BCH8_ECC: /* syndrome fragment 0 = ecc[9-12B] */ val = cpu_to_be32(*(u32 *) &ecc[9]); elm_write_reg(info, offset, val); @@ -186,7 +201,8 @@ static void elm_load_syndrome(struct elm_info *info, offset += 4; val = ecc[0]; elm_write_reg(info, offset, val); - } else { + break; + case BCH4_ECC: /* syndrome fragment 0 = ecc[20-52b] bits */ val = (cpu_to_be32(*(u32 *) &ecc[3]) >> 4) | ((ecc[2] & 0xf) << 28); @@ -196,11 +212,36 @@ static void elm_load_syndrome(struct elm_info *info, offset += 4; val = cpu_to_be32(*(u32 *) &ecc[0]) >> 12; elm_write_reg(info, offset, val); + break; + case BCH16_ECC: + val = cpu_to_be32(*(u32 *) &ecc[22]); + elm_write_reg(info, offset, val); + offset += 4; + val = cpu_to_be32(*(u32 *) &ecc[18]); + elm_write_reg(info, offset, val); + offset += 4; + val = cpu_to_be32(*(u32 *) &ecc[14]); + elm_write_reg(info, offset, val); + offset += 4; + val = cpu_to_be32(*(u32 *) &ecc[10]); + elm_write_reg(info, offset, val); + offset += 4; + val = cpu_to_be32(*(u32 *) &ecc[6]); + elm_write_reg(info, offset, val); + offset += 4; + val = cpu_to_be32(*(u32 *) &ecc[2]); + elm_write_reg(info, offset, val); + offset += 4; + val = cpu_to_be32(*(u32 *) &ecc[0]) >> 16; + elm_write_reg(info, offset, val); + break; + default: + pr_err("invalid config bch_type\n"); } } /* Update ecc pointer with ecc byte size */ - ecc += info->bch_type ? BCH8_SIZE : BCH4_SIZE; + ecc += info->ecc_syndrome_size; } } @@ -223,7 +264,7 @@ static void elm_start_processing(struct elm_info *info, * Set syndrome vector valid, so that ELM module * will process it for vectors error is reported */ - for (i = 0; i < ERROR_VECTOR_MAX; i++) { + for (i = 0; i < info->ecc_steps; i++) { if (err_vec[i].error_reported) { offset = ELM_SYNDROME_FRAGMENT_6 + SYNDROME_FRAGMENT_REG_SIZE * i; @@ -252,7 +293,7 @@ static void elm_error_correction(struct elm_info *info, int offset; u32 reg_val; - for (i = 0; i < ERROR_VECTOR_MAX; i++) { + for (i = 0; i < info->ecc_steps; i++) { /* Check error reported */ if (err_vec[i].error_reported) { @@ -354,10 +395,8 @@ static int elm_probe(struct platform_device *pdev) struct elm_info *info; info = devm_kzalloc(&pdev->dev, sizeof(*info), GFP_KERNEL); - if (!info) { - dev_err(&pdev->dev, "failed to allocate memory\n"); + if (!info) return -ENOMEM; - } info->dev = &pdev->dev; @@ -380,7 +419,7 @@ static int elm_probe(struct platform_device *pdev) } pm_runtime_enable(&pdev->dev); - if (pm_runtime_get_sync(&pdev->dev)) { + if (pm_runtime_get_sync(&pdev->dev) < 0) { ret = -EINVAL; pm_runtime_disable(&pdev->dev); dev_err(&pdev->dev, "can't enable clock\n"); @@ -401,6 +440,7 @@ static int elm_remove(struct platform_device *pdev) return 0; } +#ifdef CONFIG_PM_SLEEP /** * elm_context_save * saves ELM configurations to preserve them across Hardware powered-down @@ -418,6 +458,13 @@ static int elm_context_save(struct elm_info *info) for (i = 0; i < ERROR_VECTOR_MAX; i++) { offset = i * SYNDROME_FRAGMENT_REG_SIZE; switch (bch_type) { + case BCH16_ECC: + regs->elm_syndrome_fragment_6[i] = elm_read_reg(info, + ELM_SYNDROME_FRAGMENT_6 + offset); + regs->elm_syndrome_fragment_5[i] = elm_read_reg(info, + ELM_SYNDROME_FRAGMENT_5 + offset); + regs->elm_syndrome_fragment_4[i] = elm_read_reg(info, + ELM_SYNDROME_FRAGMENT_4 + offset); case BCH8_ECC: regs->elm_syndrome_fragment_3[i] = elm_read_reg(info, ELM_SYNDROME_FRAGMENT_3 + offset); @@ -428,6 +475,7 @@ static int elm_context_save(struct elm_info *info) ELM_SYNDROME_FRAGMENT_1 + offset); regs->elm_syndrome_fragment_0[i] = elm_read_reg(info, ELM_SYNDROME_FRAGMENT_0 + offset); + break; default: return -EINVAL; } @@ -456,6 +504,13 @@ static int elm_context_restore(struct elm_info *info) for (i = 0; i < ERROR_VECTOR_MAX; i++) { offset = i * SYNDROME_FRAGMENT_REG_SIZE; switch (bch_type) { + case BCH16_ECC: + elm_write_reg(info, ELM_SYNDROME_FRAGMENT_6 + offset, + regs->elm_syndrome_fragment_6[i]); + elm_write_reg(info, ELM_SYNDROME_FRAGMENT_5 + offset, + regs->elm_syndrome_fragment_5[i]); + elm_write_reg(info, ELM_SYNDROME_FRAGMENT_4 + offset, + regs->elm_syndrome_fragment_4[i]); case BCH8_ECC: elm_write_reg(info, ELM_SYNDROME_FRAGMENT_3 + offset, regs->elm_syndrome_fragment_3[i]); @@ -466,6 +521,7 @@ static int elm_context_restore(struct elm_info *info) regs->elm_syndrome_fragment_1[i]); elm_write_reg(info, ELM_SYNDROME_FRAGMENT_0 + offset, regs->elm_syndrome_fragment_0[i]); + break; default: return -EINVAL; } @@ -492,6 +548,7 @@ static int elm_resume(struct device *dev) elm_context_restore(info); return 0; } +#endif static SIMPLE_DEV_PM_OPS(elm_pm_ops, elm_suspend, elm_resume); @@ -505,7 +562,7 @@ MODULE_DEVICE_TABLE(of, elm_of_match); static struct platform_driver elm_driver = { .driver = { - .name = "elm", + .name = DRIVER_NAME, .owner = THIS_MODULE, .of_match_table = of_match_ptr(elm_of_match), .pm = &elm_pm_ops, diff --git a/drivers/mtd/devices/m25p80.c b/drivers/mtd/devices/m25p80.c index ad191390970..ed7e0a1bed3 100644 --- a/drivers/mtd/devices/m25p80.c +++ b/drivers/mtd/devices/m25p80.c @@ -15,484 +15,102 @@ * */ -#include <linux/init.h> #include <linux/err.h> #include <linux/errno.h> #include <linux/module.h> #include <linux/device.h> -#include <linux/interrupt.h> -#include <linux/mutex.h> -#include <linux/math64.h> -#include <linux/slab.h> -#include <linux/sched.h> -#include <linux/mod_devicetable.h> -#include <linux/mtd/cfi.h> #include <linux/mtd/mtd.h> #include <linux/mtd/partitions.h> -#include <linux/of_platform.h> #include <linux/spi/spi.h> #include <linux/spi/flash.h> +#include <linux/mtd/spi-nor.h> -/* Flash opcodes. */ -#define OPCODE_WREN 0x06 /* Write enable */ -#define OPCODE_RDSR 0x05 /* Read status register */ -#define OPCODE_WRSR 0x01 /* Write status register 1 byte */ -#define OPCODE_NORM_READ 0x03 /* Read data bytes (low frequency) */ -#define OPCODE_FAST_READ 0x0b /* Read data bytes (high frequency) */ -#define OPCODE_QUAD_READ 0x6b /* Read data bytes */ -#define OPCODE_PP 0x02 /* Page program (up to 256 bytes) */ -#define OPCODE_BE_4K 0x20 /* Erase 4KiB block */ -#define OPCODE_BE_4K_PMC 0xd7 /* Erase 4KiB block on PMC chips */ -#define OPCODE_BE_32K 0x52 /* Erase 32KiB block */ -#define OPCODE_CHIP_ERASE 0xc7 /* Erase whole flash chip */ -#define OPCODE_SE 0xd8 /* Sector erase (usually 64KiB) */ -#define OPCODE_RDID 0x9f /* Read JEDEC ID */ -#define OPCODE_RDCR 0x35 /* Read configuration register */ - -/* 4-byte address opcodes - used on Spansion and some Macronix flashes. */ -#define OPCODE_NORM_READ_4B 0x13 /* Read data bytes (low frequency) */ -#define OPCODE_FAST_READ_4B 0x0c /* Read data bytes (high frequency) */ -#define OPCODE_QUAD_READ_4B 0x6c /* Read data bytes */ -#define OPCODE_PP_4B 0x12 /* Page program (up to 256 bytes) */ -#define OPCODE_SE_4B 0xdc /* Sector erase (usually 64KiB) */ - -/* Used for SST flashes only. */ -#define OPCODE_BP 0x02 /* Byte program */ -#define OPCODE_WRDI 0x04 /* Write disable */ -#define OPCODE_AAI_WP 0xad /* Auto address increment word program */ - -/* Used for Macronix and Winbond flashes. */ -#define OPCODE_EN4B 0xb7 /* Enter 4-byte mode */ -#define OPCODE_EX4B 0xe9 /* Exit 4-byte mode */ - -/* Used for Spansion flashes only. */ -#define OPCODE_BRWR 0x17 /* Bank register write */ - -/* Status Register bits. */ -#define SR_WIP 1 /* Write in progress */ -#define SR_WEL 2 /* Write enable latch */ -/* meaning of other SR_* bits may differ between vendors */ -#define SR_BP0 4 /* Block protect 0 */ -#define SR_BP1 8 /* Block protect 1 */ -#define SR_BP2 0x10 /* Block protect 2 */ -#define SR_SRWD 0x80 /* SR write protect */ - -#define SR_QUAD_EN_MX 0x40 /* Macronix Quad I/O */ - -/* Configuration Register bits. */ -#define CR_QUAD_EN_SPAN 0x2 /* Spansion Quad I/O */ - -/* Define max times to check status register before we give up. */ -#define MAX_READY_WAIT_JIFFIES (40 * HZ) /* M25P16 specs 40s max chip erase */ #define MAX_CMD_SIZE 6 - -#define JEDEC_MFR(_jedec_id) ((_jedec_id) >> 16) - -/****************************************************************************/ - -enum read_type { - M25P80_NORMAL = 0, - M25P80_FAST, - M25P80_QUAD, -}; - struct m25p { struct spi_device *spi; - struct mutex lock; + struct spi_nor spi_nor; struct mtd_info mtd; - u16 page_size; - u16 addr_width; - u8 erase_opcode; - u8 read_opcode; - u8 program_opcode; - u8 *command; - enum read_type flash_read; + u8 command[MAX_CMD_SIZE]; }; -static inline struct m25p *mtd_to_m25p(struct mtd_info *mtd) -{ - return container_of(mtd, struct m25p, mtd); -} - -/****************************************************************************/ - -/* - * Internal helper functions - */ - -/* - * Read the status register, returning its value in the location - * Return the status register value. - * Returns negative if error occurred. - */ -static int read_sr(struct m25p *flash) -{ - ssize_t retval; - u8 code = OPCODE_RDSR; - u8 val; - - retval = spi_write_then_read(flash->spi, &code, 1, &val, 1); - - if (retval < 0) { - dev_err(&flash->spi->dev, "error %d reading SR\n", - (int) retval); - return retval; - } - - return val; -} - -/* - * Read configuration register, returning its value in the - * location. Return the configuration register value. - * Returns negative if error occured. - */ -static int read_cr(struct m25p *flash) -{ - u8 code = OPCODE_RDCR; - int ret; - u8 val; - - ret = spi_write_then_read(flash->spi, &code, 1, &val, 1); - if (ret < 0) { - dev_err(&flash->spi->dev, "error %d reading CR\n", ret); - return ret; - } - - return val; -} - -/* - * Write status register 1 byte - * Returns negative if error occurred. - */ -static int write_sr(struct m25p *flash, u8 val) -{ - flash->command[0] = OPCODE_WRSR; - flash->command[1] = val; - - return spi_write(flash->spi, flash->command, 2); -} - -/* - * Set write enable latch with Write Enable command. - * Returns negative if error occurred. - */ -static inline int write_enable(struct m25p *flash) -{ - u8 code = OPCODE_WREN; - - return spi_write_then_read(flash->spi, &code, 1, NULL, 0); -} - -/* - * Send write disble instruction to the chip. - */ -static inline int write_disable(struct m25p *flash) -{ - u8 code = OPCODE_WRDI; - - return spi_write_then_read(flash->spi, &code, 1, NULL, 0); -} - -/* - * Enable/disable 4-byte addressing mode. - */ -static inline int set_4byte(struct m25p *flash, u32 jedec_id, int enable) -{ - int status; - bool need_wren = false; - - switch (JEDEC_MFR(jedec_id)) { - case CFI_MFR_ST: /* Micron, actually */ - /* Some Micron need WREN command; all will accept it */ - need_wren = true; - case CFI_MFR_MACRONIX: - case 0xEF /* winbond */: - if (need_wren) - write_enable(flash); - - flash->command[0] = enable ? OPCODE_EN4B : OPCODE_EX4B; - status = spi_write(flash->spi, flash->command, 1); - - if (need_wren) - write_disable(flash); - - return status; - default: - /* Spansion style */ - flash->command[0] = OPCODE_BRWR; - flash->command[1] = enable << 7; - return spi_write(flash->spi, flash->command, 2); - } -} - -/* - * Service routine to read status register until ready, or timeout occurs. - * Returns non-zero if error. - */ -static int wait_till_ready(struct m25p *flash) -{ - unsigned long deadline; - int sr; - - deadline = jiffies + MAX_READY_WAIT_JIFFIES; - - do { - if ((sr = read_sr(flash)) < 0) - break; - else if (!(sr & SR_WIP)) - return 0; - - cond_resched(); - - } while (!time_after_eq(jiffies, deadline)); - - return 1; -} - -/* - * Write status Register and configuration register with 2 bytes - * The first byte will be written to the status register, while the - * second byte will be written to the configuration register. - * Return negative if error occured. - */ -static int write_sr_cr(struct m25p *flash, u16 val) -{ - flash->command[0] = OPCODE_WRSR; - flash->command[1] = val & 0xff; - flash->command[2] = (val >> 8); - - return spi_write(flash->spi, flash->command, 3); -} - -static int macronix_quad_enable(struct m25p *flash) -{ - int ret, val; - u8 cmd[2]; - cmd[0] = OPCODE_WRSR; - - val = read_sr(flash); - cmd[1] = val | SR_QUAD_EN_MX; - write_enable(flash); - - spi_write(flash->spi, &cmd, 2); - - if (wait_till_ready(flash)) - return 1; - - ret = read_sr(flash); - if (!(ret > 0 && (ret & SR_QUAD_EN_MX))) { - dev_err(&flash->spi->dev, "Macronix Quad bit not set\n"); - return -EINVAL; - } - - return 0; -} - -static int spansion_quad_enable(struct m25p *flash) +static int m25p80_read_reg(struct spi_nor *nor, u8 code, u8 *val, int len) { + struct m25p *flash = nor->priv; + struct spi_device *spi = flash->spi; int ret; - int quad_en = CR_QUAD_EN_SPAN << 8; - - write_enable(flash); - ret = write_sr_cr(flash, quad_en); - if (ret < 0) { - dev_err(&flash->spi->dev, - "error while writing configuration register\n"); - return -EINVAL; - } - - /* read back and check it */ - ret = read_cr(flash); - if (!(ret > 0 && (ret & CR_QUAD_EN_SPAN))) { - dev_err(&flash->spi->dev, "Spansion Quad bit not set\n"); - return -EINVAL; - } - - return 0; -} - -static int set_quad_mode(struct m25p *flash, u32 jedec_id) -{ - int status; - - switch (JEDEC_MFR(jedec_id)) { - case CFI_MFR_MACRONIX: - status = macronix_quad_enable(flash); - if (status) { - dev_err(&flash->spi->dev, - "Macronix quad-read not enabled\n"); - return -EINVAL; - } - return status; - default: - status = spansion_quad_enable(flash); - if (status) { - dev_err(&flash->spi->dev, - "Spansion quad-read not enabled\n"); - return -EINVAL; - } - return status; - } -} - -/* - * Erase the whole flash memory - * - * Returns 0 if successful, non-zero otherwise. - */ -static int erase_chip(struct m25p *flash) -{ - pr_debug("%s: %s %lldKiB\n", dev_name(&flash->spi->dev), __func__, - (long long)(flash->mtd.size >> 10)); + ret = spi_write_then_read(spi, &code, 1, val, len); + if (ret < 0) + dev_err(&spi->dev, "error %d reading %x\n", ret, code); - /* Wait until finished previous write command. */ - if (wait_till_ready(flash)) - return 1; - - /* Send write enable, then erase commands. */ - write_enable(flash); - - /* Set up command buffer. */ - flash->command[0] = OPCODE_CHIP_ERASE; - - spi_write(flash->spi, flash->command, 1); - - return 0; + return ret; } -static void m25p_addr2cmd(struct m25p *flash, unsigned int addr, u8 *cmd) +static void m25p_addr2cmd(struct spi_nor *nor, unsigned int addr, u8 *cmd) { /* opcode is in cmd[0] */ - cmd[1] = addr >> (flash->addr_width * 8 - 8); - cmd[2] = addr >> (flash->addr_width * 8 - 16); - cmd[3] = addr >> (flash->addr_width * 8 - 24); - cmd[4] = addr >> (flash->addr_width * 8 - 32); + cmd[1] = addr >> (nor->addr_width * 8 - 8); + cmd[2] = addr >> (nor->addr_width * 8 - 16); + cmd[3] = addr >> (nor->addr_width * 8 - 24); + cmd[4] = addr >> (nor->addr_width * 8 - 32); } -static int m25p_cmdsz(struct m25p *flash) +static int m25p_cmdsz(struct spi_nor *nor) { - return 1 + flash->addr_width; + return 1 + nor->addr_width; } -/* - * Erase one sector of flash memory at offset ``offset'' which is any - * address within the sector which should be erased. - * - * Returns 0 if successful, non-zero otherwise. - */ -static int erase_sector(struct m25p *flash, u32 offset) +static int m25p80_write_reg(struct spi_nor *nor, u8 opcode, u8 *buf, int len, + int wr_en) { - pr_debug("%s: %s %dKiB at 0x%08x\n", dev_name(&flash->spi->dev), - __func__, flash->mtd.erasesize / 1024, offset); - - /* Wait until finished previous write command. */ - if (wait_till_ready(flash)) - return 1; + struct m25p *flash = nor->priv; + struct spi_device *spi = flash->spi; - /* Send write enable, then erase commands. */ - write_enable(flash); - - /* Set up command buffer. */ - flash->command[0] = flash->erase_opcode; - m25p_addr2cmd(flash, offset, flash->command); - - spi_write(flash->spi, flash->command, m25p_cmdsz(flash)); + flash->command[0] = opcode; + if (buf) + memcpy(&flash->command[1], buf, len); - return 0; + return spi_write(spi, flash->command, len + 1); } -/****************************************************************************/ - -/* - * MTD implementation - */ - -/* - * Erase an address range on the flash chip. The address range may extend - * one or more erase sectors. Return an error is there is a problem erasing. - */ -static int m25p80_erase(struct mtd_info *mtd, struct erase_info *instr) +static void m25p80_write(struct spi_nor *nor, loff_t to, size_t len, + size_t *retlen, const u_char *buf) { - struct m25p *flash = mtd_to_m25p(mtd); - u32 addr,len; - uint32_t rem; - - pr_debug("%s: %s at 0x%llx, len %lld\n", dev_name(&flash->spi->dev), - __func__, (long long)instr->addr, - (long long)instr->len); - - div_u64_rem(instr->len, mtd->erasesize, &rem); - if (rem) - return -EINVAL; - - addr = instr->addr; - len = instr->len; - - mutex_lock(&flash->lock); - - /* whole-chip erase? */ - if (len == flash->mtd.size) { - if (erase_chip(flash)) { - instr->state = MTD_ERASE_FAILED; - mutex_unlock(&flash->lock); - return -EIO; - } + struct m25p *flash = nor->priv; + struct spi_device *spi = flash->spi; + struct spi_transfer t[2] = {}; + struct spi_message m; + int cmd_sz = m25p_cmdsz(nor); - /* REVISIT in some cases we could speed up erasing large regions - * by using OPCODE_SE instead of OPCODE_BE_4K. We may have set up - * to use "small sector erase", but that's not always optimal. - */ + spi_message_init(&m); - /* "sector"-at-a-time erase */ - } else { - while (len) { - if (erase_sector(flash, addr)) { - instr->state = MTD_ERASE_FAILED; - mutex_unlock(&flash->lock); - return -EIO; - } + if (nor->program_opcode == SPINOR_OP_AAI_WP && nor->sst_write_second) + cmd_sz = 1; - addr += mtd->erasesize; - len -= mtd->erasesize; - } - } + flash->command[0] = nor->program_opcode; + m25p_addr2cmd(nor, to, flash->command); - mutex_unlock(&flash->lock); + t[0].tx_buf = flash->command; + t[0].len = cmd_sz; + spi_message_add_tail(&t[0], &m); - instr->state = MTD_ERASE_DONE; - mtd_erase_callback(instr); + t[1].tx_buf = buf; + t[1].len = len; + spi_message_add_tail(&t[1], &m); - return 0; -} + spi_sync(spi, &m); -/* - * Dummy Cycle calculation for different type of read. - * It can be used to support more commands with - * different dummy cycle requirements. - */ -static inline int m25p80_dummy_cycles_read(struct m25p *flash) -{ - switch (flash->flash_read) { - case M25P80_FAST: - case M25P80_QUAD: - return 1; - case M25P80_NORMAL: - return 0; - default: - dev_err(&flash->spi->dev, "No valid read type supported\n"); - return -1; - } + *retlen += m.actual_length - cmd_sz; } -static inline unsigned int m25p80_rx_nbits(const struct m25p *flash) +static inline unsigned int m25p80_rx_nbits(struct spi_nor *nor) { - switch (flash->flash_read) { - case M25P80_QUAD: + switch (nor->flash_read) { + case SPI_NOR_DUAL: + return 2; + case SPI_NOR_QUAD: return 4; default: return 0; @@ -500,588 +118,72 @@ static inline unsigned int m25p80_rx_nbits(const struct m25p *flash) } /* - * Read an address range from the flash chip. The address range + * Read an address range from the nor chip. The address range * may be any size provided it is within the physical boundaries. */ -static int m25p80_read(struct mtd_info *mtd, loff_t from, size_t len, - size_t *retlen, u_char *buf) +static int m25p80_read(struct spi_nor *nor, loff_t from, size_t len, + size_t *retlen, u_char *buf) { - struct m25p *flash = mtd_to_m25p(mtd); + struct m25p *flash = nor->priv; + struct spi_device *spi = flash->spi; struct spi_transfer t[2]; struct spi_message m; - uint8_t opcode; - int dummy; + int dummy = nor->read_dummy; + int ret; - pr_debug("%s: %s from 0x%08x, len %zd\n", dev_name(&flash->spi->dev), - __func__, (u32)from, len); + /* Wait till previous write/erase is done. */ + ret = nor->wait_till_ready(nor); + if (ret) + return ret; spi_message_init(&m); memset(t, 0, (sizeof t)); - dummy = m25p80_dummy_cycles_read(flash); - if (dummy < 0) { - dev_err(&flash->spi->dev, "No valid read command supported\n"); - return -EINVAL; - } + flash->command[0] = nor->read_opcode; + m25p_addr2cmd(nor, from, flash->command); t[0].tx_buf = flash->command; - t[0].len = m25p_cmdsz(flash) + dummy; + t[0].len = m25p_cmdsz(nor) + dummy; spi_message_add_tail(&t[0], &m); t[1].rx_buf = buf; - t[1].rx_nbits = m25p80_rx_nbits(flash); + t[1].rx_nbits = m25p80_rx_nbits(nor); t[1].len = len; spi_message_add_tail(&t[1], &m); - mutex_lock(&flash->lock); - - /* Wait till previous write/erase is done. */ - if (wait_till_ready(flash)) { - /* REVISIT status return?? */ - mutex_unlock(&flash->lock); - return 1; - } - - /* Set up the write data buffer. */ - opcode = flash->read_opcode; - flash->command[0] = opcode; - m25p_addr2cmd(flash, from, flash->command); - - spi_sync(flash->spi, &m); - - *retlen = m.actual_length - m25p_cmdsz(flash) - dummy; - - mutex_unlock(&flash->lock); + spi_sync(spi, &m); + *retlen = m.actual_length - m25p_cmdsz(nor) - dummy; return 0; } -/* - * Write an address range to the flash chip. Data must be written in - * FLASH_PAGESIZE chunks. The address range may be any size provided - * it is within the physical boundaries. - */ -static int m25p80_write(struct mtd_info *mtd, loff_t to, size_t len, - size_t *retlen, const u_char *buf) +static int m25p80_erase(struct spi_nor *nor, loff_t offset) { - struct m25p *flash = mtd_to_m25p(mtd); - u32 page_offset, page_size; - struct spi_transfer t[2]; - struct spi_message m; - - pr_debug("%s: %s to 0x%08x, len %zd\n", dev_name(&flash->spi->dev), - __func__, (u32)to, len); - - spi_message_init(&m); - memset(t, 0, (sizeof t)); - - t[0].tx_buf = flash->command; - t[0].len = m25p_cmdsz(flash); - spi_message_add_tail(&t[0], &m); - - t[1].tx_buf = buf; - spi_message_add_tail(&t[1], &m); - - mutex_lock(&flash->lock); - - /* Wait until finished previous write command. */ - if (wait_till_ready(flash)) { - mutex_unlock(&flash->lock); - return 1; - } - - write_enable(flash); - - /* Set up the opcode in the write buffer. */ - flash->command[0] = flash->program_opcode; - m25p_addr2cmd(flash, to, flash->command); - - page_offset = to & (flash->page_size - 1); - - /* do all the bytes fit onto one page? */ - if (page_offset + len <= flash->page_size) { - t[1].len = len; - - spi_sync(flash->spi, &m); - - *retlen = m.actual_length - m25p_cmdsz(flash); - } else { - u32 i; - - /* the size of data remaining on the first page */ - page_size = flash->page_size - page_offset; - - t[1].len = page_size; - spi_sync(flash->spi, &m); - - *retlen = m.actual_length - m25p_cmdsz(flash); - - /* write everything in flash->page_size chunks */ - for (i = page_size; i < len; i += page_size) { - page_size = len - i; - if (page_size > flash->page_size) - page_size = flash->page_size; - - /* write the next page to flash */ - m25p_addr2cmd(flash, to + i, flash->command); - - t[1].tx_buf = buf + i; - t[1].len = page_size; - - wait_till_ready(flash); - - write_enable(flash); - - spi_sync(flash->spi, &m); - - *retlen += m.actual_length - m25p_cmdsz(flash); - } - } - - mutex_unlock(&flash->lock); - - return 0; -} - -static int sst_write(struct mtd_info *mtd, loff_t to, size_t len, - size_t *retlen, const u_char *buf) -{ - struct m25p *flash = mtd_to_m25p(mtd); - struct spi_transfer t[2]; - struct spi_message m; - size_t actual; - int cmd_sz, ret; - - pr_debug("%s: %s to 0x%08x, len %zd\n", dev_name(&flash->spi->dev), - __func__, (u32)to, len); - - spi_message_init(&m); - memset(t, 0, (sizeof t)); - - t[0].tx_buf = flash->command; - t[0].len = m25p_cmdsz(flash); - spi_message_add_tail(&t[0], &m); - - t[1].tx_buf = buf; - spi_message_add_tail(&t[1], &m); + struct m25p *flash = nor->priv; + int ret; - mutex_lock(&flash->lock); + dev_dbg(nor->dev, "%dKiB at 0x%08x\n", + flash->mtd.erasesize / 1024, (u32)offset); /* Wait until finished previous write command. */ - ret = wait_till_ready(flash); + ret = nor->wait_till_ready(nor); if (ret) - goto time_out; - - write_enable(flash); - - actual = to % 2; - /* Start write from odd address. */ - if (actual) { - flash->command[0] = OPCODE_BP; - m25p_addr2cmd(flash, to, flash->command); - - /* write one byte. */ - t[1].len = 1; - spi_sync(flash->spi, &m); - ret = wait_till_ready(flash); - if (ret) - goto time_out; - *retlen += m.actual_length - m25p_cmdsz(flash); - } - to += actual; - - flash->command[0] = OPCODE_AAI_WP; - m25p_addr2cmd(flash, to, flash->command); - - /* Write out most of the data here. */ - cmd_sz = m25p_cmdsz(flash); - for (; actual < len - 1; actual += 2) { - t[0].len = cmd_sz; - /* write two bytes. */ - t[1].len = 2; - t[1].tx_buf = buf + actual; + return ret; - spi_sync(flash->spi, &m); - ret = wait_till_ready(flash); - if (ret) - goto time_out; - *retlen += m.actual_length - cmd_sz; - cmd_sz = 1; - to += 2; - } - write_disable(flash); - ret = wait_till_ready(flash); + /* Send write enable, then erase commands. */ + ret = nor->write_reg(nor, SPINOR_OP_WREN, NULL, 0, 0); if (ret) - goto time_out; - - /* Write out trailing byte if it exists. */ - if (actual != len) { - write_enable(flash); - flash->command[0] = OPCODE_BP; - m25p_addr2cmd(flash, to, flash->command); - t[0].len = m25p_cmdsz(flash); - t[1].len = 1; - t[1].tx_buf = buf + actual; - - spi_sync(flash->spi, &m); - ret = wait_till_ready(flash); - if (ret) - goto time_out; - *retlen += m.actual_length - m25p_cmdsz(flash); - write_disable(flash); - } - -time_out: - mutex_unlock(&flash->lock); - return ret; -} - -static int m25p80_lock(struct mtd_info *mtd, loff_t ofs, uint64_t len) -{ - struct m25p *flash = mtd_to_m25p(mtd); - uint32_t offset = ofs; - uint8_t status_old, status_new; - int res = 0; - - mutex_lock(&flash->lock); - /* Wait until finished previous command */ - if (wait_till_ready(flash)) { - res = 1; - goto err; - } - - status_old = read_sr(flash); - - if (offset < flash->mtd.size-(flash->mtd.size/2)) - status_new = status_old | SR_BP2 | SR_BP1 | SR_BP0; - else if (offset < flash->mtd.size-(flash->mtd.size/4)) - status_new = (status_old & ~SR_BP0) | SR_BP2 | SR_BP1; - else if (offset < flash->mtd.size-(flash->mtd.size/8)) - status_new = (status_old & ~SR_BP1) | SR_BP2 | SR_BP0; - else if (offset < flash->mtd.size-(flash->mtd.size/16)) - status_new = (status_old & ~(SR_BP0|SR_BP1)) | SR_BP2; - else if (offset < flash->mtd.size-(flash->mtd.size/32)) - status_new = (status_old & ~SR_BP2) | SR_BP1 | SR_BP0; - else if (offset < flash->mtd.size-(flash->mtd.size/64)) - status_new = (status_old & ~(SR_BP2|SR_BP0)) | SR_BP1; - else - status_new = (status_old & ~(SR_BP2|SR_BP1)) | SR_BP0; - - /* Only modify protection if it will not unlock other areas */ - if ((status_new&(SR_BP2|SR_BP1|SR_BP0)) > - (status_old&(SR_BP2|SR_BP1|SR_BP0))) { - write_enable(flash); - if (write_sr(flash, status_new) < 0) { - res = 1; - goto err; - } - } - -err: mutex_unlock(&flash->lock); - return res; -} - -static int m25p80_unlock(struct mtd_info *mtd, loff_t ofs, uint64_t len) -{ - struct m25p *flash = mtd_to_m25p(mtd); - uint32_t offset = ofs; - uint8_t status_old, status_new; - int res = 0; - - mutex_lock(&flash->lock); - /* Wait until finished previous command */ - if (wait_till_ready(flash)) { - res = 1; - goto err; - } - - status_old = read_sr(flash); - - if (offset+len > flash->mtd.size-(flash->mtd.size/64)) - status_new = status_old & ~(SR_BP2|SR_BP1|SR_BP0); - else if (offset+len > flash->mtd.size-(flash->mtd.size/32)) - status_new = (status_old & ~(SR_BP2|SR_BP1)) | SR_BP0; - else if (offset+len > flash->mtd.size-(flash->mtd.size/16)) - status_new = (status_old & ~(SR_BP2|SR_BP0)) | SR_BP1; - else if (offset+len > flash->mtd.size-(flash->mtd.size/8)) - status_new = (status_old & ~SR_BP2) | SR_BP1 | SR_BP0; - else if (offset+len > flash->mtd.size-(flash->mtd.size/4)) - status_new = (status_old & ~(SR_BP0|SR_BP1)) | SR_BP2; - else if (offset+len > flash->mtd.size-(flash->mtd.size/2)) - status_new = (status_old & ~SR_BP1) | SR_BP2 | SR_BP0; - else - status_new = (status_old & ~SR_BP0) | SR_BP2 | SR_BP1; - - /* Only modify protection if it will not lock other areas */ - if ((status_new&(SR_BP2|SR_BP1|SR_BP0)) < - (status_old&(SR_BP2|SR_BP1|SR_BP0))) { - write_enable(flash); - if (write_sr(flash, status_new) < 0) { - res = 1; - goto err; - } - } - -err: mutex_unlock(&flash->lock); - return res; -} - -/****************************************************************************/ - -/* - * SPI device driver setup and teardown - */ - -struct flash_info { - /* JEDEC id zero means "no ID" (most older chips); otherwise it has - * a high byte of zero plus three data bytes: the manufacturer id, - * then a two byte device id. - */ - u32 jedec_id; - u16 ext_id; - - /* The size listed here is what works with OPCODE_SE, which isn't - * necessarily called a "sector" by the vendor. - */ - unsigned sector_size; - u16 n_sectors; - - u16 page_size; - u16 addr_width; - - u16 flags; -#define SECT_4K 0x01 /* OPCODE_BE_4K works uniformly */ -#define M25P_NO_ERASE 0x02 /* No erase command needed */ -#define SST_WRITE 0x04 /* use SST byte programming */ -#define M25P_NO_FR 0x08 /* Can't do fastread */ -#define SECT_4K_PMC 0x10 /* OPCODE_BE_4K_PMC works uniformly */ -#define M25P80_QUAD_READ 0x20 /* Flash supports Quad Read */ -}; - -#define INFO(_jedec_id, _ext_id, _sector_size, _n_sectors, _flags) \ - ((kernel_ulong_t)&(struct flash_info) { \ - .jedec_id = (_jedec_id), \ - .ext_id = (_ext_id), \ - .sector_size = (_sector_size), \ - .n_sectors = (_n_sectors), \ - .page_size = 256, \ - .flags = (_flags), \ - }) - -#define CAT25_INFO(_sector_size, _n_sectors, _page_size, _addr_width, _flags) \ - ((kernel_ulong_t)&(struct flash_info) { \ - .sector_size = (_sector_size), \ - .n_sectors = (_n_sectors), \ - .page_size = (_page_size), \ - .addr_width = (_addr_width), \ - .flags = (_flags), \ - }) - -/* NOTE: double check command sets and memory organization when you add - * more flash chips. This current list focusses on newer chips, which - * have been converging on command sets which including JEDEC ID. - */ -static const struct spi_device_id m25p_ids[] = { - /* Atmel -- some are (confusingly) marketed as "DataFlash" */ - { "at25fs010", INFO(0x1f6601, 0, 32 * 1024, 4, SECT_4K) }, - { "at25fs040", INFO(0x1f6604, 0, 64 * 1024, 8, SECT_4K) }, - - { "at25df041a", INFO(0x1f4401, 0, 64 * 1024, 8, SECT_4K) }, - { "at25df321a", INFO(0x1f4701, 0, 64 * 1024, 64, SECT_4K) }, - { "at25df641", INFO(0x1f4800, 0, 64 * 1024, 128, SECT_4K) }, - - { "at26f004", INFO(0x1f0400, 0, 64 * 1024, 8, SECT_4K) }, - { "at26df081a", INFO(0x1f4501, 0, 64 * 1024, 16, SECT_4K) }, - { "at26df161a", INFO(0x1f4601, 0, 64 * 1024, 32, SECT_4K) }, - { "at26df321", INFO(0x1f4700, 0, 64 * 1024, 64, SECT_4K) }, - - { "at45db081d", INFO(0x1f2500, 0, 64 * 1024, 16, SECT_4K) }, - - /* EON -- en25xxx */ - { "en25f32", INFO(0x1c3116, 0, 64 * 1024, 64, SECT_4K) }, - { "en25p32", INFO(0x1c2016, 0, 64 * 1024, 64, 0) }, - { "en25q32b", INFO(0x1c3016, 0, 64 * 1024, 64, 0) }, - { "en25p64", INFO(0x1c2017, 0, 64 * 1024, 128, 0) }, - { "en25q64", INFO(0x1c3017, 0, 64 * 1024, 128, SECT_4K) }, - { "en25qh256", INFO(0x1c7019, 0, 64 * 1024, 512, 0) }, - - /* ESMT */ - { "f25l32pa", INFO(0x8c2016, 0, 64 * 1024, 64, SECT_4K) }, - - /* Everspin */ - { "mr25h256", CAT25_INFO( 32 * 1024, 1, 256, 2, M25P_NO_ERASE | M25P_NO_FR) }, - { "mr25h10", CAT25_INFO(128 * 1024, 1, 256, 3, M25P_NO_ERASE | M25P_NO_FR) }, - - /* GigaDevice */ - { "gd25q32", INFO(0xc84016, 0, 64 * 1024, 64, SECT_4K) }, - { "gd25q64", INFO(0xc84017, 0, 64 * 1024, 128, SECT_4K) }, - - /* Intel/Numonyx -- xxxs33b */ - { "160s33b", INFO(0x898911, 0, 64 * 1024, 32, 0) }, - { "320s33b", INFO(0x898912, 0, 64 * 1024, 64, 0) }, - { "640s33b", INFO(0x898913, 0, 64 * 1024, 128, 0) }, - - /* Macronix */ - { "mx25l2005a", INFO(0xc22012, 0, 64 * 1024, 4, SECT_4K) }, - { "mx25l4005a", INFO(0xc22013, 0, 64 * 1024, 8, SECT_4K) }, - { "mx25l8005", INFO(0xc22014, 0, 64 * 1024, 16, 0) }, - { "mx25l1606e", INFO(0xc22015, 0, 64 * 1024, 32, SECT_4K) }, - { "mx25l3205d", INFO(0xc22016, 0, 64 * 1024, 64, 0) }, - { "mx25l3255e", INFO(0xc29e16, 0, 64 * 1024, 64, SECT_4K) }, - { "mx25l6405d", INFO(0xc22017, 0, 64 * 1024, 128, 0) }, - { "mx25l12805d", INFO(0xc22018, 0, 64 * 1024, 256, 0) }, - { "mx25l12855e", INFO(0xc22618, 0, 64 * 1024, 256, 0) }, - { "mx25l25635e", INFO(0xc22019, 0, 64 * 1024, 512, 0) }, - { "mx25l25655e", INFO(0xc22619, 0, 64 * 1024, 512, 0) }, - { "mx66l51235l", INFO(0xc2201a, 0, 64 * 1024, 1024, M25P80_QUAD_READ) }, - - /* Micron */ - { "n25q064", INFO(0x20ba17, 0, 64 * 1024, 128, 0) }, - { "n25q128a11", INFO(0x20bb18, 0, 64 * 1024, 256, 0) }, - { "n25q128a13", INFO(0x20ba18, 0, 64 * 1024, 256, 0) }, - { "n25q256a", INFO(0x20ba19, 0, 64 * 1024, 512, SECT_4K) }, - { "n25q512a", INFO(0x20bb20, 0, 64 * 1024, 1024, SECT_4K) }, - - /* PMC */ - { "pm25lv512", INFO(0, 0, 32 * 1024, 2, SECT_4K_PMC) }, - { "pm25lv010", INFO(0, 0, 32 * 1024, 4, SECT_4K_PMC) }, - { "pm25lq032", INFO(0x7f9d46, 0, 64 * 1024, 64, SECT_4K) }, - - /* Spansion -- single (large) sector size only, at least - * for the chips listed here (without boot sectors). - */ - { "s25sl032p", INFO(0x010215, 0x4d00, 64 * 1024, 64, 0) }, - { "s25sl064p", INFO(0x010216, 0x4d00, 64 * 1024, 128, 0) }, - { "s25fl256s0", INFO(0x010219, 0x4d00, 256 * 1024, 128, 0) }, - { "s25fl256s1", INFO(0x010219, 0x4d01, 64 * 1024, 512, M25P80_QUAD_READ) }, - { "s25fl512s", INFO(0x010220, 0x4d00, 256 * 1024, 256, M25P80_QUAD_READ) }, - { "s70fl01gs", INFO(0x010221, 0x4d00, 256 * 1024, 256, 0) }, - { "s25sl12800", INFO(0x012018, 0x0300, 256 * 1024, 64, 0) }, - { "s25sl12801", INFO(0x012018, 0x0301, 64 * 1024, 256, 0) }, - { "s25fl129p0", INFO(0x012018, 0x4d00, 256 * 1024, 64, 0) }, - { "s25fl129p1", INFO(0x012018, 0x4d01, 64 * 1024, 256, 0) }, - { "s25sl004a", INFO(0x010212, 0, 64 * 1024, 8, 0) }, - { "s25sl008a", INFO(0x010213, 0, 64 * 1024, 16, 0) }, - { "s25sl016a", INFO(0x010214, 0, 64 * 1024, 32, 0) }, - { "s25sl032a", INFO(0x010215, 0, 64 * 1024, 64, 0) }, - { "s25sl064a", INFO(0x010216, 0, 64 * 1024, 128, 0) }, - { "s25fl016k", INFO(0xef4015, 0, 64 * 1024, 32, SECT_4K) }, - { "s25fl064k", INFO(0xef4017, 0, 64 * 1024, 128, SECT_4K) }, - - /* SST -- large erase sizes are "overlays", "sectors" are 4K */ - { "sst25vf040b", INFO(0xbf258d, 0, 64 * 1024, 8, SECT_4K | SST_WRITE) }, - { "sst25vf080b", INFO(0xbf258e, 0, 64 * 1024, 16, SECT_4K | SST_WRITE) }, - { "sst25vf016b", INFO(0xbf2541, 0, 64 * 1024, 32, SECT_4K | SST_WRITE) }, - { "sst25vf032b", INFO(0xbf254a, 0, 64 * 1024, 64, SECT_4K | SST_WRITE) }, - { "sst25vf064c", INFO(0xbf254b, 0, 64 * 1024, 128, SECT_4K) }, - { "sst25wf512", INFO(0xbf2501, 0, 64 * 1024, 1, SECT_4K | SST_WRITE) }, - { "sst25wf010", INFO(0xbf2502, 0, 64 * 1024, 2, SECT_4K | SST_WRITE) }, - { "sst25wf020", INFO(0xbf2503, 0, 64 * 1024, 4, SECT_4K | SST_WRITE) }, - { "sst25wf040", INFO(0xbf2504, 0, 64 * 1024, 8, SECT_4K | SST_WRITE) }, - - /* ST Microelectronics -- newer production may have feature updates */ - { "m25p05", INFO(0x202010, 0, 32 * 1024, 2, 0) }, - { "m25p10", INFO(0x202011, 0, 32 * 1024, 4, 0) }, - { "m25p20", INFO(0x202012, 0, 64 * 1024, 4, 0) }, - { "m25p40", INFO(0x202013, 0, 64 * 1024, 8, 0) }, - { "m25p80", INFO(0x202014, 0, 64 * 1024, 16, 0) }, - { "m25p16", INFO(0x202015, 0, 64 * 1024, 32, 0) }, - { "m25p32", INFO(0x202016, 0, 64 * 1024, 64, 0) }, - { "m25p64", INFO(0x202017, 0, 64 * 1024, 128, 0) }, - { "m25p128", INFO(0x202018, 0, 256 * 1024, 64, 0) }, - { "n25q032", INFO(0x20ba16, 0, 64 * 1024, 64, 0) }, - - { "m25p05-nonjedec", INFO(0, 0, 32 * 1024, 2, 0) }, - { "m25p10-nonjedec", INFO(0, 0, 32 * 1024, 4, 0) }, - { "m25p20-nonjedec", INFO(0, 0, 64 * 1024, 4, 0) }, - { "m25p40-nonjedec", INFO(0, 0, 64 * 1024, 8, 0) }, - { "m25p80-nonjedec", INFO(0, 0, 64 * 1024, 16, 0) }, - { "m25p16-nonjedec", INFO(0, 0, 64 * 1024, 32, 0) }, - { "m25p32-nonjedec", INFO(0, 0, 64 * 1024, 64, 0) }, - { "m25p64-nonjedec", INFO(0, 0, 64 * 1024, 128, 0) }, - { "m25p128-nonjedec", INFO(0, 0, 256 * 1024, 64, 0) }, - - { "m45pe10", INFO(0x204011, 0, 64 * 1024, 2, 0) }, - { "m45pe80", INFO(0x204014, 0, 64 * 1024, 16, 0) }, - { "m45pe16", INFO(0x204015, 0, 64 * 1024, 32, 0) }, - - { "m25pe20", INFO(0x208012, 0, 64 * 1024, 4, 0) }, - { "m25pe80", INFO(0x208014, 0, 64 * 1024, 16, 0) }, - { "m25pe16", INFO(0x208015, 0, 64 * 1024, 32, SECT_4K) }, - - { "m25px16", INFO(0x207115, 0, 64 * 1024, 32, SECT_4K) }, - { "m25px32", INFO(0x207116, 0, 64 * 1024, 64, SECT_4K) }, - { "m25px32-s0", INFO(0x207316, 0, 64 * 1024, 64, SECT_4K) }, - { "m25px32-s1", INFO(0x206316, 0, 64 * 1024, 64, SECT_4K) }, - { "m25px64", INFO(0x207117, 0, 64 * 1024, 128, 0) }, - - /* Winbond -- w25x "blocks" are 64K, "sectors" are 4KiB */ - { "w25x10", INFO(0xef3011, 0, 64 * 1024, 2, SECT_4K) }, - { "w25x20", INFO(0xef3012, 0, 64 * 1024, 4, SECT_4K) }, - { "w25x40", INFO(0xef3013, 0, 64 * 1024, 8, SECT_4K) }, - { "w25x80", INFO(0xef3014, 0, 64 * 1024, 16, SECT_4K) }, - { "w25x16", INFO(0xef3015, 0, 64 * 1024, 32, SECT_4K) }, - { "w25x32", INFO(0xef3016, 0, 64 * 1024, 64, SECT_4K) }, - { "w25q32", INFO(0xef4016, 0, 64 * 1024, 64, SECT_4K) }, - { "w25q32dw", INFO(0xef6016, 0, 64 * 1024, 64, SECT_4K) }, - { "w25x64", INFO(0xef3017, 0, 64 * 1024, 128, SECT_4K) }, - { "w25q64", INFO(0xef4017, 0, 64 * 1024, 128, SECT_4K) }, - { "w25q128", INFO(0xef4018, 0, 64 * 1024, 256, SECT_4K) }, - { "w25q80", INFO(0xef5014, 0, 64 * 1024, 16, SECT_4K) }, - { "w25q80bl", INFO(0xef4014, 0, 64 * 1024, 16, SECT_4K) }, - { "w25q128", INFO(0xef4018, 0, 64 * 1024, 256, SECT_4K) }, - { "w25q256", INFO(0xef4019, 0, 64 * 1024, 512, SECT_4K) }, - - /* Catalyst / On Semiconductor -- non-JEDEC */ - { "cat25c11", CAT25_INFO( 16, 8, 16, 1, M25P_NO_ERASE | M25P_NO_FR) }, - { "cat25c03", CAT25_INFO( 32, 8, 16, 2, M25P_NO_ERASE | M25P_NO_FR) }, - { "cat25c09", CAT25_INFO( 128, 8, 32, 2, M25P_NO_ERASE | M25P_NO_FR) }, - { "cat25c17", CAT25_INFO( 256, 8, 32, 2, M25P_NO_ERASE | M25P_NO_FR) }, - { "cat25128", CAT25_INFO(2048, 8, 64, 2, M25P_NO_ERASE | M25P_NO_FR) }, - { }, -}; -MODULE_DEVICE_TABLE(spi, m25p_ids); - -static const struct spi_device_id *jedec_probe(struct spi_device *spi) -{ - int tmp; - u8 code = OPCODE_RDID; - u8 id[5]; - u32 jedec; - u16 ext_jedec; - struct flash_info *info; + return ret; - /* JEDEC also defines an optional "extended device information" - * string for after vendor-specific data, after the three bytes - * we use here. Supporting some chips might require using it. - */ - tmp = spi_write_then_read(spi, &code, 1, id, 5); - if (tmp < 0) { - pr_debug("%s: error %d reading JEDEC ID\n", - dev_name(&spi->dev), tmp); - return ERR_PTR(tmp); - } - jedec = id[0]; - jedec = jedec << 8; - jedec |= id[1]; - jedec = jedec << 8; - jedec |= id[2]; + /* Set up command buffer. */ + flash->command[0] = nor->erase_opcode; + m25p_addr2cmd(nor, offset, flash->command); - ext_jedec = id[3] << 8 | id[4]; + spi_write(flash->spi, flash->command, m25p_cmdsz(nor)); - for (tmp = 0; tmp < ARRAY_SIZE(m25p_ids) - 1; tmp++) { - info = (void *)m25p_ids[tmp].driver_data; - if (info->jedec_id == jedec) { - if (info->ext_id != 0 && info->ext_id != ext_jedec) - continue; - return &m25p_ids[tmp]; - } - } - dev_err(&spi->dev, "unrecognized JEDEC id %06x\n", jedec); - return ERR_PTR(-ENODEV); + return 0; } - /* * board specific setup should have ensured the SPI clock used here * matches what the READ command supports, at least until this driver @@ -1089,223 +191,45 @@ static const struct spi_device_id *jedec_probe(struct spi_device *spi) */ static int m25p_probe(struct spi_device *spi) { - const struct spi_device_id *id = spi_get_device_id(spi); - struct flash_platform_data *data; - struct m25p *flash; - struct flash_info *info; - unsigned i; struct mtd_part_parser_data ppdata; - struct device_node *np = spi->dev.of_node; + struct flash_platform_data *data; + struct m25p *flash; + struct spi_nor *nor; + enum read_mode mode = SPI_NOR_NORMAL; int ret; - /* Platform data helps sort out which chip type we have, as - * well as how this board partitions it. If we don't have - * a chip ID, try the JEDEC id commands; they'll work for most - * newer chips, even if we don't recognize the particular chip. - */ - data = dev_get_platdata(&spi->dev); - if (data && data->type) { - const struct spi_device_id *plat_id; - - for (i = 0; i < ARRAY_SIZE(m25p_ids) - 1; i++) { - plat_id = &m25p_ids[i]; - if (strcmp(data->type, plat_id->name)) - continue; - break; - } - - if (i < ARRAY_SIZE(m25p_ids) - 1) - id = plat_id; - else - dev_warn(&spi->dev, "unrecognized id %s\n", data->type); - } - - info = (void *)id->driver_data; - - if (info->jedec_id) { - const struct spi_device_id *jid; - - jid = jedec_probe(spi); - if (IS_ERR(jid)) { - return PTR_ERR(jid); - } else if (jid != id) { - /* - * JEDEC knows better, so overwrite platform ID. We - * can't trust partitions any longer, but we'll let - * mtd apply them anyway, since some partitions may be - * marked read-only, and we don't want to lose that - * information, even if it's not 100% accurate. - */ - dev_warn(&spi->dev, "found %s, expected %s\n", - jid->name, id->name); - id = jid; - info = (void *)jid->driver_data; - } - } - flash = devm_kzalloc(&spi->dev, sizeof(*flash), GFP_KERNEL); if (!flash) return -ENOMEM; - flash->command = devm_kzalloc(&spi->dev, MAX_CMD_SIZE, GFP_KERNEL); - if (!flash->command) - return -ENOMEM; - - flash->spi = spi; - mutex_init(&flash->lock); - spi_set_drvdata(spi, flash); - - /* - * Atmel, SST and Intel/Numonyx serial flash tend to power - * up with the software protection bits set - */ + nor = &flash->spi_nor; - if (JEDEC_MFR(info->jedec_id) == CFI_MFR_ATMEL || - JEDEC_MFR(info->jedec_id) == CFI_MFR_INTEL || - JEDEC_MFR(info->jedec_id) == CFI_MFR_SST) { - write_enable(flash); - write_sr(flash, 0); - } - - if (data && data->name) - flash->mtd.name = data->name; - else - flash->mtd.name = dev_name(&spi->dev); - - flash->mtd.type = MTD_NORFLASH; - flash->mtd.writesize = 1; - flash->mtd.flags = MTD_CAP_NORFLASH; - flash->mtd.size = info->sector_size * info->n_sectors; - flash->mtd._erase = m25p80_erase; - flash->mtd._read = m25p80_read; - - /* flash protection support for STmicro chips */ - if (JEDEC_MFR(info->jedec_id) == CFI_MFR_ST) { - flash->mtd._lock = m25p80_lock; - flash->mtd._unlock = m25p80_unlock; - } + /* install the hooks */ + nor->read = m25p80_read; + nor->write = m25p80_write; + nor->erase = m25p80_erase; + nor->write_reg = m25p80_write_reg; + nor->read_reg = m25p80_read_reg; - /* sst flash chips use AAI word program */ - if (info->flags & SST_WRITE) - flash->mtd._write = sst_write; - else - flash->mtd._write = m25p80_write; + nor->dev = &spi->dev; + nor->mtd = &flash->mtd; + nor->priv = flash; - /* prefer "small sector" erase if possible */ - if (info->flags & SECT_4K) { - flash->erase_opcode = OPCODE_BE_4K; - flash->mtd.erasesize = 4096; - } else if (info->flags & SECT_4K_PMC) { - flash->erase_opcode = OPCODE_BE_4K_PMC; - flash->mtd.erasesize = 4096; - } else { - flash->erase_opcode = OPCODE_SE; - flash->mtd.erasesize = info->sector_size; - } + spi_set_drvdata(spi, flash); + flash->mtd.priv = nor; + flash->spi = spi; - if (info->flags & M25P_NO_ERASE) - flash->mtd.flags |= MTD_NO_ERASE; + if (spi->mode & SPI_RX_QUAD) + mode = SPI_NOR_QUAD; + else if (spi->mode & SPI_RX_DUAL) + mode = SPI_NOR_DUAL; + ret = spi_nor_scan(nor, spi_get_device_id(spi), mode); + if (ret) + return ret; + data = dev_get_platdata(&spi->dev); ppdata.of_node = spi->dev.of_node; - flash->mtd.dev.parent = &spi->dev; - flash->page_size = info->page_size; - flash->mtd.writebufsize = flash->page_size; - - if (np) { - /* If we were instantiated by DT, use it */ - if (of_property_read_bool(np, "m25p,fast-read")) - flash->flash_read = M25P80_FAST; - else - flash->flash_read = M25P80_NORMAL; - } else { - /* If we weren't instantiated by DT, default to fast-read */ - flash->flash_read = M25P80_FAST; - } - - /* Some devices cannot do fast-read, no matter what DT tells us */ - if (info->flags & M25P_NO_FR) - flash->flash_read = M25P80_NORMAL; - - /* Quad-read mode takes precedence over fast/normal */ - if (spi->mode & SPI_RX_QUAD && info->flags & M25P80_QUAD_READ) { - ret = set_quad_mode(flash, info->jedec_id); - if (ret) { - dev_err(&flash->spi->dev, "quad mode not supported\n"); - return ret; - } - flash->flash_read = M25P80_QUAD; - } - /* Default commands */ - switch (flash->flash_read) { - case M25P80_QUAD: - flash->read_opcode = OPCODE_QUAD_READ; - break; - case M25P80_FAST: - flash->read_opcode = OPCODE_FAST_READ; - break; - case M25P80_NORMAL: - flash->read_opcode = OPCODE_NORM_READ; - break; - default: - dev_err(&flash->spi->dev, "No Read opcode defined\n"); - return -EINVAL; - } - - flash->program_opcode = OPCODE_PP; - - if (info->addr_width) - flash->addr_width = info->addr_width; - else if (flash->mtd.size > 0x1000000) { - /* enable 4-byte addressing if the device exceeds 16MiB */ - flash->addr_width = 4; - if (JEDEC_MFR(info->jedec_id) == CFI_MFR_AMD) { - /* Dedicated 4-byte command set */ - switch (flash->flash_read) { - case M25P80_QUAD: - flash->read_opcode = OPCODE_QUAD_READ_4B; - break; - case M25P80_FAST: - flash->read_opcode = OPCODE_FAST_READ_4B; - break; - case M25P80_NORMAL: - flash->read_opcode = OPCODE_NORM_READ_4B; - break; - } - flash->program_opcode = OPCODE_PP_4B; - /* No small sector erase for 4-byte command set */ - flash->erase_opcode = OPCODE_SE_4B; - flash->mtd.erasesize = info->sector_size; - } else - set_4byte(flash, info->jedec_id, 1); - } else { - flash->addr_width = 3; - } - - dev_info(&spi->dev, "%s (%lld Kbytes)\n", id->name, - (long long)flash->mtd.size >> 10); - - pr_debug("mtd .name = %s, .size = 0x%llx (%lldMiB) " - ".erasesize = 0x%.8x (%uKiB) .numeraseregions = %d\n", - flash->mtd.name, - (long long)flash->mtd.size, (long long)(flash->mtd.size >> 20), - flash->mtd.erasesize, flash->mtd.erasesize / 1024, - flash->mtd.numeraseregions); - - if (flash->mtd.numeraseregions) - for (i = 0; i < flash->mtd.numeraseregions; i++) - pr_debug("mtd.eraseregions[%d] = { .offset = 0x%llx, " - ".erasesize = 0x%.8x (%uKiB), " - ".numblocks = %d }\n", - i, (long long)flash->mtd.eraseregions[i].offset, - flash->mtd.eraseregions[i].erasesize, - flash->mtd.eraseregions[i].erasesize / 1024, - flash->mtd.eraseregions[i].numblocks); - - - /* partitions should match sector boundaries; and it may be good to - * use readonly partitions for writeprotected sectors (BP2..BP0). - */ return mtd_device_parse_register(&flash->mtd, NULL, &ppdata, data ? data->parts : NULL, data ? data->nr_parts : 0); @@ -1326,7 +250,7 @@ static struct spi_driver m25p80_driver = { .name = "m25p80", .owner = THIS_MODULE, }, - .id_table = m25p_ids, + .id_table = spi_nor_ids, .probe = m25p_probe, .remove = m25p_remove, diff --git a/drivers/mtd/devices/mtd_dataflash.c b/drivers/mtd/devices/mtd_dataflash.c index 624069de4f2..dd22ce2cc9a 100644 --- a/drivers/mtd/devices/mtd_dataflash.c +++ b/drivers/mtd/devices/mtd_dataflash.c @@ -10,7 +10,6 @@ * 2 of the License, or (at your option) any later version. */ #include <linux/module.h> -#include <linux/init.h> #include <linux/slab.h> #include <linux/delay.h> #include <linux/device.h> @@ -440,8 +439,8 @@ static int dataflash_write(struct mtd_info *mtd, loff_t to, size_t len, #ifdef CONFIG_MTD_DATAFLASH_OTP -static int dataflash_get_otp_info(struct mtd_info *mtd, - struct otp_info *info, size_t len) +static int dataflash_get_otp_info(struct mtd_info *mtd, size_t len, + size_t *retlen, struct otp_info *info) { /* Report both blocks as identical: bytes 0..64, locked. * Unless the user block changed from all-ones, we can't @@ -450,7 +449,8 @@ static int dataflash_get_otp_info(struct mtd_info *mtd, info->start = 0; info->length = 64; info->locked = 1; - return sizeof(*info); + *retlen = sizeof(*info); + return 0; } static ssize_t otp_read(struct spi_device *spi, unsigned base, @@ -542,14 +542,18 @@ static int dataflash_write_user_otp(struct mtd_info *mtd, struct dataflash *priv = mtd->priv; int status; - if (len > 64) - return -EINVAL; + if (from >= 64) { + /* + * Attempting to write beyond the end of OTP memory, + * no data can be written. + */ + *retlen = 0; + return 0; + } - /* Strictly speaking, we *could* truncate the write ... but - * let's not do that for the only write that's ever possible. - */ + /* Truncate the write to fit into OTP memory. */ if ((from + len) > 64) - return -EINVAL; + len = 64 - from; /* OUT: OP_WRITE_SECURITY, 3 zeroes, 64 data-or-zero bytes * IN: ignore all diff --git a/drivers/mtd/devices/phram.c b/drivers/mtd/devices/phram.c index e1f2aebaa48..2cceebfb251 100644 --- a/drivers/mtd/devices/phram.c +++ b/drivers/mtd/devices/phram.c @@ -205,6 +205,8 @@ static inline void kill_final_newline(char *str) return 1; \ } while (0) +#ifndef MODULE +static int phram_init_called; /* * This shall contain the module parameter if any. It is of the form: * - phram=<device>,<address>,<size> for module case @@ -213,9 +215,10 @@ static inline void kill_final_newline(char *str) * size. * Example: phram.phram=rootfs,0xa0000000,512Mi */ -static __initdata char phram_paramline[64 + 20 + 20]; +static char phram_paramline[64 + 20 + 20]; +#endif -static int __init phram_setup(const char *val) +static int phram_setup(const char *val) { char buf[64 + 20 + 20], *str = buf; char *token[3]; @@ -264,17 +267,36 @@ static int __init phram_setup(const char *val) return ret; } -static int __init phram_param_call(const char *val, struct kernel_param *kp) +static int phram_param_call(const char *val, struct kernel_param *kp) { +#ifdef MODULE + return phram_setup(val); +#else /* - * This function is always called before 'init_phram()', whether - * built-in or module. + * If more parameters are later passed in via + * /sys/module/phram/parameters/phram + * and init_phram() has already been called, + * we can parse the argument now. */ + + if (phram_init_called) + return phram_setup(val); + + /* + * During early boot stage, we only save the parameters + * here. We must parse them later: if the param passed + * from kernel boot command line, phram_param_call() is + * called so early that it is not possible to resolve + * the device (even kmalloc() fails). Defer that work to + * phram_setup(). + */ + if (strlen(val) >= sizeof(phram_paramline)) return -ENOSPC; strcpy(phram_paramline, val); return 0; +#endif } module_param_call(phram, phram_param_call, NULL, NULL, 000); @@ -283,10 +305,15 @@ MODULE_PARM_DESC(phram, "Memory region to map. \"phram=<name>,<start>,<length>\" static int __init init_phram(void) { + int ret = 0; + +#ifndef MODULE if (phram_paramline[0]) - return phram_setup(phram_paramline); + ret = phram_setup(phram_paramline); + phram_init_called = 1; +#endif - return 0; + return ret; } static void __exit cleanup_phram(void) diff --git a/drivers/mtd/devices/pmc551.c b/drivers/mtd/devices/pmc551.c index 0c51b988e1f..f02603e1bfe 100644 --- a/drivers/mtd/devices/pmc551.c +++ b/drivers/mtd/devices/pmc551.c @@ -725,16 +725,11 @@ static int __init init_pmc551(void) } mtd = kzalloc(sizeof(struct mtd_info), GFP_KERNEL); - if (!mtd) { - printk(KERN_NOTICE "pmc551: Cannot allocate new MTD " - "device.\n"); + if (!mtd) break; - } priv = kzalloc(sizeof(struct mypriv), GFP_KERNEL); if (!priv) { - printk(KERN_NOTICE "pmc551: Cannot allocate new MTD " - "device.\n"); kfree(mtd); break; } diff --git a/drivers/mtd/devices/serial_flash_cmds.h b/drivers/mtd/devices/serial_flash_cmds.h new file mode 100644 index 00000000000..f59a125295d --- /dev/null +++ b/drivers/mtd/devices/serial_flash_cmds.h @@ -0,0 +1,61 @@ +/* + * Generic/SFDP Flash Commands and Device Capabilities + * + * Copyright (C) 2013 Lee Jones <lee.jones@lianro.org> + * + * This code is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#ifndef _MTD_SERIAL_FLASH_CMDS_H +#define _MTD_SERIAL_FLASH_CMDS_H + +/* Generic Flash Commands/OPCODEs */ +#define SPINOR_OP_RDSR2 0x35 +#define SPINOR_OP_WRVCR 0x81 +#define SPINOR_OP_RDVCR 0x85 + +/* JEDEC Standard - Serial Flash Discoverable Parmeters (SFDP) Commands */ +#define SPINOR_OP_READ_1_2_2 0xbb /* DUAL I/O READ */ +#define SPINOR_OP_READ_1_4_4 0xeb /* QUAD I/O READ */ + +#define SPINOR_OP_WRITE 0x02 /* PAGE PROGRAM */ +#define SPINOR_OP_WRITE_1_1_2 0xa2 /* DUAL INPUT PROGRAM */ +#define SPINOR_OP_WRITE_1_2_2 0xd2 /* DUAL INPUT EXT PROGRAM */ +#define SPINOR_OP_WRITE_1_1_4 0x32 /* QUAD INPUT PROGRAM */ +#define SPINOR_OP_WRITE_1_4_4 0x12 /* QUAD INPUT EXT PROGRAM */ + +/* READ commands with 32-bit addressing */ +#define SPINOR_OP_READ4_1_2_2 0xbc +#define SPINOR_OP_READ4_1_4_4 0xec + +/* Configuration flags */ +#define FLASH_FLAG_SINGLE 0x000000ff +#define FLASH_FLAG_READ_WRITE 0x00000001 +#define FLASH_FLAG_READ_FAST 0x00000002 +#define FLASH_FLAG_SE_4K 0x00000004 +#define FLASH_FLAG_SE_32K 0x00000008 +#define FLASH_FLAG_CE 0x00000010 +#define FLASH_FLAG_32BIT_ADDR 0x00000020 +#define FLASH_FLAG_RESET 0x00000040 +#define FLASH_FLAG_DYB_LOCKING 0x00000080 + +#define FLASH_FLAG_DUAL 0x0000ff00 +#define FLASH_FLAG_READ_1_1_2 0x00000100 +#define FLASH_FLAG_READ_1_2_2 0x00000200 +#define FLASH_FLAG_READ_2_2_2 0x00000400 +#define FLASH_FLAG_WRITE_1_1_2 0x00001000 +#define FLASH_FLAG_WRITE_1_2_2 0x00002000 +#define FLASH_FLAG_WRITE_2_2_2 0x00004000 + +#define FLASH_FLAG_QUAD 0x00ff0000 +#define FLASH_FLAG_READ_1_1_4 0x00010000 +#define FLASH_FLAG_READ_1_4_4 0x00020000 +#define FLASH_FLAG_READ_4_4_4 0x00040000 +#define FLASH_FLAG_WRITE_1_1_4 0x00100000 +#define FLASH_FLAG_WRITE_1_4_4 0x00200000 +#define FLASH_FLAG_WRITE_4_4_4 0x00400000 + +#endif /* _MTD_SERIAL_FLASH_CMDS_H */ diff --git a/drivers/mtd/devices/slram.c b/drivers/mtd/devices/slram.c index 5a5cd2ace4a..2fc4957cbe7 100644 --- a/drivers/mtd/devices/slram.c +++ b/drivers/mtd/devices/slram.c @@ -280,14 +280,11 @@ __setup("slram=", mtd_slram_setup); static int __init init_slram(void) { char *devname; - int i; #ifndef MODULE char *devstart; char *devlength; - i = 0; - if (!map) { E("slram: not enough parameters.\n"); return(-EINVAL); @@ -314,6 +311,7 @@ static int __init init_slram(void) } #else int count; + int i; for (count = 0; count < SLRAM_MAX_DEVICES_PARAMS && map[count]; count++) { diff --git a/drivers/mtd/devices/spear_smi.c b/drivers/mtd/devices/spear_smi.c index 42382141206..c4176b0f382 100644 --- a/drivers/mtd/devices/spear_smi.c +++ b/drivers/mtd/devices/spear_smi.c @@ -6,7 +6,7 @@ * * Copyright © 2010 STMicroelectronics. * Ashish Priyadarshi - * Shiraz Hashim <shiraz.hashim@st.com> + * Shiraz Hashim <shiraz.linux.kernel@gmail.com> * * This file is licensed under the terms of the GNU General Public * License version 2. This program is licensed "as is" without any @@ -913,7 +913,6 @@ static int spear_smi_probe(struct platform_device *pdev) if (np) { pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL); if (!pdata) { - pr_err("%s: ERROR: no memory", __func__); ret = -ENOMEM; goto err; } @@ -943,7 +942,6 @@ static int spear_smi_probe(struct platform_device *pdev) dev = devm_kzalloc(&pdev->dev, sizeof(*dev), GFP_ATOMIC); if (!dev) { ret = -ENOMEM; - dev_err(&pdev->dev, "mem alloc fail\n"); goto err; } @@ -1091,5 +1089,5 @@ static struct platform_driver spear_smi_driver = { module_platform_driver(spear_smi_driver); MODULE_LICENSE("GPL"); -MODULE_AUTHOR("Ashish Priyadarshi, Shiraz Hashim <shiraz.hashim@st.com>"); +MODULE_AUTHOR("Ashish Priyadarshi, Shiraz Hashim <shiraz.linux.kernel@gmail.com>"); MODULE_DESCRIPTION("MTD SMI driver for serial nor flash chips"); diff --git a/drivers/mtd/devices/sst25l.c b/drivers/mtd/devices/sst25l.c index 687bf27ec85..c63ecbcad0b 100644 --- a/drivers/mtd/devices/sst25l.c +++ b/drivers/mtd/devices/sst25l.c @@ -15,7 +15,6 @@ * */ -#include <linux/init.h> #include <linux/module.h> #include <linux/device.h> #include <linux/mutex.h> diff --git a/drivers/mtd/devices/st_spi_fsm.c b/drivers/mtd/devices/st_spi_fsm.c new file mode 100644 index 00000000000..d252514d3e9 --- /dev/null +++ b/drivers/mtd/devices/st_spi_fsm.c @@ -0,0 +1,2080 @@ +/* + * st_spi_fsm.c - ST Fast Sequence Mode (FSM) Serial Flash Controller + * + * Author: Angus Clark <angus.clark@st.com> + * + * Copyright (C) 2010-2014 STMicroelectronics Limited + * + * JEDEC probe based on drivers/mtd/devices/m25p80.c + * + * This code is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/regmap.h> +#include <linux/platform_device.h> +#include <linux/mfd/syscon.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/partitions.h> +#include <linux/mtd/spi-nor.h> +#include <linux/sched.h> +#include <linux/delay.h> +#include <linux/io.h> +#include <linux/of.h> + +#include "serial_flash_cmds.h" + +/* + * FSM SPI Controller Registers + */ +#define SPI_CLOCKDIV 0x0010 +#define SPI_MODESELECT 0x0018 +#define SPI_CONFIGDATA 0x0020 +#define SPI_STA_MODE_CHANGE 0x0028 +#define SPI_FAST_SEQ_TRANSFER_SIZE 0x0100 +#define SPI_FAST_SEQ_ADD1 0x0104 +#define SPI_FAST_SEQ_ADD2 0x0108 +#define SPI_FAST_SEQ_ADD_CFG 0x010c +#define SPI_FAST_SEQ_OPC1 0x0110 +#define SPI_FAST_SEQ_OPC2 0x0114 +#define SPI_FAST_SEQ_OPC3 0x0118 +#define SPI_FAST_SEQ_OPC4 0x011c +#define SPI_FAST_SEQ_OPC5 0x0120 +#define SPI_MODE_BITS 0x0124 +#define SPI_DUMMY_BITS 0x0128 +#define SPI_FAST_SEQ_FLASH_STA_DATA 0x012c +#define SPI_FAST_SEQ_1 0x0130 +#define SPI_FAST_SEQ_2 0x0134 +#define SPI_FAST_SEQ_3 0x0138 +#define SPI_FAST_SEQ_4 0x013c +#define SPI_FAST_SEQ_CFG 0x0140 +#define SPI_FAST_SEQ_STA 0x0144 +#define SPI_QUAD_BOOT_SEQ_INIT_1 0x0148 +#define SPI_QUAD_BOOT_SEQ_INIT_2 0x014c +#define SPI_QUAD_BOOT_READ_SEQ_1 0x0150 +#define SPI_QUAD_BOOT_READ_SEQ_2 0x0154 +#define SPI_PROGRAM_ERASE_TIME 0x0158 +#define SPI_MULT_PAGE_REPEAT_SEQ_1 0x015c +#define SPI_MULT_PAGE_REPEAT_SEQ_2 0x0160 +#define SPI_STATUS_WR_TIME_REG 0x0164 +#define SPI_FAST_SEQ_DATA_REG 0x0300 + +/* + * Register: SPI_MODESELECT + */ +#define SPI_MODESELECT_CONTIG 0x01 +#define SPI_MODESELECT_FASTREAD 0x02 +#define SPI_MODESELECT_DUALIO 0x04 +#define SPI_MODESELECT_FSM 0x08 +#define SPI_MODESELECT_QUADBOOT 0x10 + +/* + * Register: SPI_CONFIGDATA + */ +#define SPI_CFG_DEVICE_ST 0x1 +#define SPI_CFG_DEVICE_ATMEL 0x4 +#define SPI_CFG_MIN_CS_HIGH(x) (((x) & 0xfff) << 4) +#define SPI_CFG_CS_SETUPHOLD(x) (((x) & 0xff) << 16) +#define SPI_CFG_DATA_HOLD(x) (((x) & 0xff) << 24) + +#define SPI_CFG_DEFAULT_MIN_CS_HIGH SPI_CFG_MIN_CS_HIGH(0x0AA) +#define SPI_CFG_DEFAULT_CS_SETUPHOLD SPI_CFG_CS_SETUPHOLD(0xA0) +#define SPI_CFG_DEFAULT_DATA_HOLD SPI_CFG_DATA_HOLD(0x00) + +/* + * Register: SPI_FAST_SEQ_TRANSFER_SIZE + */ +#define TRANSFER_SIZE(x) ((x) * 8) + +/* + * Register: SPI_FAST_SEQ_ADD_CFG + */ +#define ADR_CFG_CYCLES_ADD1(x) ((x) << 0) +#define ADR_CFG_PADS_1_ADD1 (0x0 << 6) +#define ADR_CFG_PADS_2_ADD1 (0x1 << 6) +#define ADR_CFG_PADS_4_ADD1 (0x3 << 6) +#define ADR_CFG_CSDEASSERT_ADD1 (1 << 8) +#define ADR_CFG_CYCLES_ADD2(x) ((x) << (0+16)) +#define ADR_CFG_PADS_1_ADD2 (0x0 << (6+16)) +#define ADR_CFG_PADS_2_ADD2 (0x1 << (6+16)) +#define ADR_CFG_PADS_4_ADD2 (0x3 << (6+16)) +#define ADR_CFG_CSDEASSERT_ADD2 (1 << (8+16)) + +/* + * Register: SPI_FAST_SEQ_n + */ +#define SEQ_OPC_OPCODE(x) ((x) << 0) +#define SEQ_OPC_CYCLES(x) ((x) << 8) +#define SEQ_OPC_PADS_1 (0x0 << 14) +#define SEQ_OPC_PADS_2 (0x1 << 14) +#define SEQ_OPC_PADS_4 (0x3 << 14) +#define SEQ_OPC_CSDEASSERT (1 << 16) + +/* + * Register: SPI_FAST_SEQ_CFG + */ +#define SEQ_CFG_STARTSEQ (1 << 0) +#define SEQ_CFG_SWRESET (1 << 5) +#define SEQ_CFG_CSDEASSERT (1 << 6) +#define SEQ_CFG_READNOTWRITE (1 << 7) +#define SEQ_CFG_ERASE (1 << 8) +#define SEQ_CFG_PADS_1 (0x0 << 16) +#define SEQ_CFG_PADS_2 (0x1 << 16) +#define SEQ_CFG_PADS_4 (0x3 << 16) + +/* + * Register: SPI_MODE_BITS + */ +#define MODE_DATA(x) (x & 0xff) +#define MODE_CYCLES(x) ((x & 0x3f) << 16) +#define MODE_PADS_1 (0x0 << 22) +#define MODE_PADS_2 (0x1 << 22) +#define MODE_PADS_4 (0x3 << 22) +#define DUMMY_CSDEASSERT (1 << 24) + +/* + * Register: SPI_DUMMY_BITS + */ +#define DUMMY_CYCLES(x) ((x & 0x3f) << 16) +#define DUMMY_PADS_1 (0x0 << 22) +#define DUMMY_PADS_2 (0x1 << 22) +#define DUMMY_PADS_4 (0x3 << 22) +#define DUMMY_CSDEASSERT (1 << 24) + +/* + * Register: SPI_FAST_SEQ_FLASH_STA_DATA + */ +#define STA_DATA_BYTE1(x) ((x & 0xff) << 0) +#define STA_DATA_BYTE2(x) ((x & 0xff) << 8) +#define STA_PADS_1 (0x0 << 16) +#define STA_PADS_2 (0x1 << 16) +#define STA_PADS_4 (0x3 << 16) +#define STA_CSDEASSERT (0x1 << 20) +#define STA_RDNOTWR (0x1 << 21) + +/* + * FSM SPI Instruction Opcodes + */ +#define STFSM_OPC_CMD 0x1 +#define STFSM_OPC_ADD 0x2 +#define STFSM_OPC_STA 0x3 +#define STFSM_OPC_MODE 0x4 +#define STFSM_OPC_DUMMY 0x5 +#define STFSM_OPC_DATA 0x6 +#define STFSM_OPC_WAIT 0x7 +#define STFSM_OPC_JUMP 0x8 +#define STFSM_OPC_GOTO 0x9 +#define STFSM_OPC_STOP 0xF + +/* + * FSM SPI Instructions (== opcode + operand). + */ +#define STFSM_INSTR(cmd, op) ((cmd) | ((op) << 4)) + +#define STFSM_INST_CMD1 STFSM_INSTR(STFSM_OPC_CMD, 1) +#define STFSM_INST_CMD2 STFSM_INSTR(STFSM_OPC_CMD, 2) +#define STFSM_INST_CMD3 STFSM_INSTR(STFSM_OPC_CMD, 3) +#define STFSM_INST_CMD4 STFSM_INSTR(STFSM_OPC_CMD, 4) +#define STFSM_INST_CMD5 STFSM_INSTR(STFSM_OPC_CMD, 5) +#define STFSM_INST_ADD1 STFSM_INSTR(STFSM_OPC_ADD, 1) +#define STFSM_INST_ADD2 STFSM_INSTR(STFSM_OPC_ADD, 2) + +#define STFSM_INST_DATA_WRITE STFSM_INSTR(STFSM_OPC_DATA, 1) +#define STFSM_INST_DATA_READ STFSM_INSTR(STFSM_OPC_DATA, 2) + +#define STFSM_INST_STA_RD1 STFSM_INSTR(STFSM_OPC_STA, 0x1) +#define STFSM_INST_STA_WR1 STFSM_INSTR(STFSM_OPC_STA, 0x1) +#define STFSM_INST_STA_RD2 STFSM_INSTR(STFSM_OPC_STA, 0x2) +#define STFSM_INST_STA_WR1_2 STFSM_INSTR(STFSM_OPC_STA, 0x3) + +#define STFSM_INST_MODE STFSM_INSTR(STFSM_OPC_MODE, 0) +#define STFSM_INST_DUMMY STFSM_INSTR(STFSM_OPC_DUMMY, 0) +#define STFSM_INST_WAIT STFSM_INSTR(STFSM_OPC_WAIT, 0) +#define STFSM_INST_STOP STFSM_INSTR(STFSM_OPC_STOP, 0) + +#define STFSM_DEFAULT_EMI_FREQ 100000000UL /* 100 MHz */ +#define STFSM_DEFAULT_WR_TIME (STFSM_DEFAULT_EMI_FREQ * (15/1000)) /* 15ms */ + +#define STFSM_FLASH_SAFE_FREQ 10000000UL /* 10 MHz */ + +#define STFSM_MAX_WAIT_SEQ_MS 1000 /* FSM execution time */ + +/* S25FLxxxS commands */ +#define S25FL_CMD_WRITE4_1_1_4 0x34 +#define S25FL_CMD_SE4 0xdc +#define S25FL_CMD_CLSR 0x30 +#define S25FL_CMD_DYBWR 0xe1 +#define S25FL_CMD_DYBRD 0xe0 +#define S25FL_CMD_WRITE4 0x12 /* Note, opcode clashes with + * 'SPINOR_OP_WRITE_1_4_4' + * as found on N25Qxxx devices! */ + +/* Status register */ +#define FLASH_STATUS_BUSY 0x01 +#define FLASH_STATUS_WEL 0x02 +#define FLASH_STATUS_BP0 0x04 +#define FLASH_STATUS_BP1 0x08 +#define FLASH_STATUS_BP2 0x10 +#define FLASH_STATUS_SRWP0 0x80 +#define FLASH_STATUS_TIMEOUT 0xff +/* S25FL Error Flags */ +#define S25FL_STATUS_E_ERR 0x20 +#define S25FL_STATUS_P_ERR 0x40 + +#define N25Q_CMD_WRVCR 0x81 +#define N25Q_CMD_RDVCR 0x85 +#define N25Q_CMD_RDVECR 0x65 +#define N25Q_CMD_RDNVCR 0xb5 +#define N25Q_CMD_WRNVCR 0xb1 + +#define FLASH_PAGESIZE 256 /* In Bytes */ +#define FLASH_PAGESIZE_32 (FLASH_PAGESIZE / 4) /* In uint32_t */ +#define FLASH_MAX_BUSY_WAIT (300 * HZ) /* Maximum 'CHIPERASE' time */ + +/* + * Flags to tweak operation of default read/write/erase routines + */ +#define CFG_READ_TOGGLE_32BIT_ADDR 0x00000001 +#define CFG_WRITE_TOGGLE_32BIT_ADDR 0x00000002 +#define CFG_ERASESEC_TOGGLE_32BIT_ADDR 0x00000008 +#define CFG_S25FL_CHECK_ERROR_FLAGS 0x00000010 + +struct stfsm_seq { + uint32_t data_size; + uint32_t addr1; + uint32_t addr2; + uint32_t addr_cfg; + uint32_t seq_opc[5]; + uint32_t mode; + uint32_t dummy; + uint32_t status; + uint8_t seq[16]; + uint32_t seq_cfg; +} __packed __aligned(4); + +struct stfsm { + struct device *dev; + void __iomem *base; + struct resource *region; + struct mtd_info mtd; + struct mutex lock; + struct flash_info *info; + + uint32_t configuration; + uint32_t fifo_dir_delay; + bool booted_from_spi; + bool reset_signal; + bool reset_por; + + struct stfsm_seq stfsm_seq_read; + struct stfsm_seq stfsm_seq_write; + struct stfsm_seq stfsm_seq_en_32bit_addr; +}; + +/* Parameters to configure a READ or WRITE FSM sequence */ +struct seq_rw_config { + uint32_t flags; /* flags to support config */ + uint8_t cmd; /* FLASH command */ + int write; /* Write Sequence */ + uint8_t addr_pads; /* No. of addr pads (MODE & DUMMY) */ + uint8_t data_pads; /* No. of data pads */ + uint8_t mode_data; /* MODE data */ + uint8_t mode_cycles; /* No. of MODE cycles */ + uint8_t dummy_cycles; /* No. of DUMMY cycles */ +}; + +/* SPI Flash Device Table */ +struct flash_info { + char *name; + /* + * JEDEC id zero means "no ID" (most older chips); otherwise it has + * a high byte of zero plus three data bytes: the manufacturer id, + * then a two byte device id. + */ + u32 jedec_id; + u16 ext_id; + /* + * The size listed here is what works with SPINOR_OP_SE, which isn't + * necessarily called a "sector" by the vendor. + */ + unsigned sector_size; + u16 n_sectors; + u32 flags; + /* + * Note, where FAST_READ is supported, freq_max specifies the + * FAST_READ frequency, not the READ frequency. + */ + u32 max_freq; + int (*config)(struct stfsm *); +}; + +static int stfsm_n25q_config(struct stfsm *fsm); +static int stfsm_mx25_config(struct stfsm *fsm); +static int stfsm_s25fl_config(struct stfsm *fsm); +static int stfsm_w25q_config(struct stfsm *fsm); + +static struct flash_info flash_types[] = { + /* + * ST Microelectronics/Numonyx -- + * (newer production versions may have feature updates + * (eg faster operating frequency) + */ +#define M25P_FLAG (FLASH_FLAG_READ_WRITE | FLASH_FLAG_READ_FAST) + { "m25p40", 0x202013, 0, 64 * 1024, 8, M25P_FLAG, 25, NULL }, + { "m25p80", 0x202014, 0, 64 * 1024, 16, M25P_FLAG, 25, NULL }, + { "m25p16", 0x202015, 0, 64 * 1024, 32, M25P_FLAG, 25, NULL }, + { "m25p32", 0x202016, 0, 64 * 1024, 64, M25P_FLAG, 50, NULL }, + { "m25p64", 0x202017, 0, 64 * 1024, 128, M25P_FLAG, 50, NULL }, + { "m25p128", 0x202018, 0, 256 * 1024, 64, M25P_FLAG, 50, NULL }, + +#define M25PX_FLAG (FLASH_FLAG_READ_WRITE | \ + FLASH_FLAG_READ_FAST | \ + FLASH_FLAG_READ_1_1_2 | \ + FLASH_FLAG_WRITE_1_1_2) + { "m25px32", 0x207116, 0, 64 * 1024, 64, M25PX_FLAG, 75, NULL }, + { "m25px64", 0x207117, 0, 64 * 1024, 128, M25PX_FLAG, 75, NULL }, + + /* Macronix MX25xxx + * - Support for 'FLASH_FLAG_WRITE_1_4_4' is omitted for devices + * where operating frequency must be reduced. + */ +#define MX25_FLAG (FLASH_FLAG_READ_WRITE | \ + FLASH_FLAG_READ_FAST | \ + FLASH_FLAG_READ_1_1_2 | \ + FLASH_FLAG_READ_1_2_2 | \ + FLASH_FLAG_READ_1_1_4 | \ + FLASH_FLAG_SE_4K | \ + FLASH_FLAG_SE_32K) + { "mx25l3255e", 0xc29e16, 0, 64 * 1024, 64, + (MX25_FLAG | FLASH_FLAG_WRITE_1_4_4), 86, + stfsm_mx25_config}, + { "mx25l25635e", 0xc22019, 0, 64*1024, 512, + (MX25_FLAG | FLASH_FLAG_32BIT_ADDR | FLASH_FLAG_RESET), 70, + stfsm_mx25_config }, + { "mx25l25655e", 0xc22619, 0, 64*1024, 512, + (MX25_FLAG | FLASH_FLAG_32BIT_ADDR | FLASH_FLAG_RESET), 70, + stfsm_mx25_config}, + +#define N25Q_FLAG (FLASH_FLAG_READ_WRITE | \ + FLASH_FLAG_READ_FAST | \ + FLASH_FLAG_READ_1_1_2 | \ + FLASH_FLAG_READ_1_2_2 | \ + FLASH_FLAG_READ_1_1_4 | \ + FLASH_FLAG_READ_1_4_4 | \ + FLASH_FLAG_WRITE_1_1_2 | \ + FLASH_FLAG_WRITE_1_2_2 | \ + FLASH_FLAG_WRITE_1_1_4 | \ + FLASH_FLAG_WRITE_1_4_4) + { "n25q128", 0x20ba18, 0, 64 * 1024, 256, N25Q_FLAG, 108, + stfsm_n25q_config }, + { "n25q256", 0x20ba19, 0, 64 * 1024, 512, + N25Q_FLAG | FLASH_FLAG_32BIT_ADDR, 108, stfsm_n25q_config }, + + /* + * Spansion S25FLxxxP + * - 256KiB and 64KiB sector variants (identified by ext. JEDEC) + */ +#define S25FLXXXP_FLAG (FLASH_FLAG_READ_WRITE | \ + FLASH_FLAG_READ_1_1_2 | \ + FLASH_FLAG_READ_1_2_2 | \ + FLASH_FLAG_READ_1_1_4 | \ + FLASH_FLAG_READ_1_4_4 | \ + FLASH_FLAG_WRITE_1_1_4 | \ + FLASH_FLAG_READ_FAST) + { "s25fl032p", 0x010215, 0x4d00, 64 * 1024, 64, S25FLXXXP_FLAG, 80, + stfsm_s25fl_config}, + { "s25fl129p0", 0x012018, 0x4d00, 256 * 1024, 64, S25FLXXXP_FLAG, 80, + stfsm_s25fl_config }, + { "s25fl129p1", 0x012018, 0x4d01, 64 * 1024, 256, S25FLXXXP_FLAG, 80, + stfsm_s25fl_config }, + + /* + * Spansion S25FLxxxS + * - 256KiB and 64KiB sector variants (identified by ext. JEDEC) + * - RESET# signal supported by die but not bristled out on all + * package types. The package type is a function of board design, + * so this information is captured in the board's flags. + * - Supports 'DYB' sector protection. Depending on variant, sectors + * may default to locked state on power-on. + */ +#define S25FLXXXS_FLAG (S25FLXXXP_FLAG | \ + FLASH_FLAG_RESET | \ + FLASH_FLAG_DYB_LOCKING) + { "s25fl128s0", 0x012018, 0x0300, 256 * 1024, 64, S25FLXXXS_FLAG, 80, + stfsm_s25fl_config }, + { "s25fl128s1", 0x012018, 0x0301, 64 * 1024, 256, S25FLXXXS_FLAG, 80, + stfsm_s25fl_config }, + { "s25fl256s0", 0x010219, 0x4d00, 256 * 1024, 128, + S25FLXXXS_FLAG | FLASH_FLAG_32BIT_ADDR, 80, stfsm_s25fl_config }, + { "s25fl256s1", 0x010219, 0x4d01, 64 * 1024, 512, + S25FLXXXS_FLAG | FLASH_FLAG_32BIT_ADDR, 80, stfsm_s25fl_config }, + + /* Winbond -- w25x "blocks" are 64K, "sectors" are 4KiB */ +#define W25X_FLAG (FLASH_FLAG_READ_WRITE | \ + FLASH_FLAG_READ_FAST | \ + FLASH_FLAG_READ_1_1_2 | \ + FLASH_FLAG_WRITE_1_1_2) + { "w25x40", 0xef3013, 0, 64 * 1024, 8, W25X_FLAG, 75, NULL }, + { "w25x80", 0xef3014, 0, 64 * 1024, 16, W25X_FLAG, 75, NULL }, + { "w25x16", 0xef3015, 0, 64 * 1024, 32, W25X_FLAG, 75, NULL }, + { "w25x32", 0xef3016, 0, 64 * 1024, 64, W25X_FLAG, 75, NULL }, + { "w25x64", 0xef3017, 0, 64 * 1024, 128, W25X_FLAG, 75, NULL }, + + /* Winbond -- w25q "blocks" are 64K, "sectors" are 4KiB */ +#define W25Q_FLAG (FLASH_FLAG_READ_WRITE | \ + FLASH_FLAG_READ_FAST | \ + FLASH_FLAG_READ_1_1_2 | \ + FLASH_FLAG_READ_1_2_2 | \ + FLASH_FLAG_READ_1_1_4 | \ + FLASH_FLAG_READ_1_4_4 | \ + FLASH_FLAG_WRITE_1_1_4) + { "w25q80", 0xef4014, 0, 64 * 1024, 16, W25Q_FLAG, 80, + stfsm_w25q_config }, + { "w25q16", 0xef4015, 0, 64 * 1024, 32, W25Q_FLAG, 80, + stfsm_w25q_config }, + { "w25q32", 0xef4016, 0, 64 * 1024, 64, W25Q_FLAG, 80, + stfsm_w25q_config }, + { "w25q64", 0xef4017, 0, 64 * 1024, 128, W25Q_FLAG, 80, + stfsm_w25q_config }, + + /* Sentinel */ + { NULL, 0x000000, 0, 0, 0, 0, 0, NULL }, +}; + +/* + * FSM message sequence configurations: + * + * All configs are presented in order of preference + */ + +/* Default READ configurations, in order of preference */ +static struct seq_rw_config default_read_configs[] = { + {FLASH_FLAG_READ_1_4_4, SPINOR_OP_READ_1_4_4, 0, 4, 4, 0x00, 2, 4}, + {FLASH_FLAG_READ_1_1_4, SPINOR_OP_READ_1_1_4, 0, 1, 4, 0x00, 4, 0}, + {FLASH_FLAG_READ_1_2_2, SPINOR_OP_READ_1_2_2, 0, 2, 2, 0x00, 4, 0}, + {FLASH_FLAG_READ_1_1_2, SPINOR_OP_READ_1_1_2, 0, 1, 2, 0x00, 0, 8}, + {FLASH_FLAG_READ_FAST, SPINOR_OP_READ_FAST, 0, 1, 1, 0x00, 0, 8}, + {FLASH_FLAG_READ_WRITE, SPINOR_OP_READ, 0, 1, 1, 0x00, 0, 0}, + {0x00, 0, 0, 0, 0, 0x00, 0, 0}, +}; + +/* Default WRITE configurations */ +static struct seq_rw_config default_write_configs[] = { + {FLASH_FLAG_WRITE_1_4_4, SPINOR_OP_WRITE_1_4_4, 1, 4, 4, 0x00, 0, 0}, + {FLASH_FLAG_WRITE_1_1_4, SPINOR_OP_WRITE_1_1_4, 1, 1, 4, 0x00, 0, 0}, + {FLASH_FLAG_WRITE_1_2_2, SPINOR_OP_WRITE_1_2_2, 1, 2, 2, 0x00, 0, 0}, + {FLASH_FLAG_WRITE_1_1_2, SPINOR_OP_WRITE_1_1_2, 1, 1, 2, 0x00, 0, 0}, + {FLASH_FLAG_READ_WRITE, SPINOR_OP_WRITE, 1, 1, 1, 0x00, 0, 0}, + {0x00, 0, 0, 0, 0, 0x00, 0, 0}, +}; + +/* + * [N25Qxxx] Configuration + */ +#define N25Q_VCR_DUMMY_CYCLES(x) (((x) & 0xf) << 4) +#define N25Q_VCR_XIP_DISABLED ((uint8_t)0x1 << 3) +#define N25Q_VCR_WRAP_CONT 0x3 + +/* N25Q 3-byte Address READ configurations + * - 'FAST' variants configured for 8 dummy cycles. + * + * Note, the number of dummy cycles used for 'FAST' READ operations is + * configurable and would normally be tuned according to the READ command and + * operating frequency. However, this applies universally to all 'FAST' READ + * commands, including those used by the SPIBoot controller, and remains in + * force until the device is power-cycled. Since the SPIBoot controller is + * hard-wired to use 8 dummy cycles, we must configure the device to also use 8 + * cycles. + */ +static struct seq_rw_config n25q_read3_configs[] = { + {FLASH_FLAG_READ_1_4_4, SPINOR_OP_READ_1_4_4, 0, 4, 4, 0x00, 0, 8}, + {FLASH_FLAG_READ_1_1_4, SPINOR_OP_READ_1_1_4, 0, 1, 4, 0x00, 0, 8}, + {FLASH_FLAG_READ_1_2_2, SPINOR_OP_READ_1_2_2, 0, 2, 2, 0x00, 0, 8}, + {FLASH_FLAG_READ_1_1_2, SPINOR_OP_READ_1_1_2, 0, 1, 2, 0x00, 0, 8}, + {FLASH_FLAG_READ_FAST, SPINOR_OP_READ_FAST, 0, 1, 1, 0x00, 0, 8}, + {FLASH_FLAG_READ_WRITE, SPINOR_OP_READ, 0, 1, 1, 0x00, 0, 0}, + {0x00, 0, 0, 0, 0, 0x00, 0, 0}, +}; + +/* N25Q 4-byte Address READ configurations + * - use special 4-byte address READ commands (reduces overheads, and + * reduces risk of hitting watchdog reset issues). + * - 'FAST' variants configured for 8 dummy cycles (see note above.) + */ +static struct seq_rw_config n25q_read4_configs[] = { + {FLASH_FLAG_READ_1_4_4, SPINOR_OP_READ4_1_4_4, 0, 4, 4, 0x00, 0, 8}, + {FLASH_FLAG_READ_1_1_4, SPINOR_OP_READ4_1_1_4, 0, 1, 4, 0x00, 0, 8}, + {FLASH_FLAG_READ_1_2_2, SPINOR_OP_READ4_1_2_2, 0, 2, 2, 0x00, 0, 8}, + {FLASH_FLAG_READ_1_1_2, SPINOR_OP_READ4_1_1_2, 0, 1, 2, 0x00, 0, 8}, + {FLASH_FLAG_READ_FAST, SPINOR_OP_READ4_FAST, 0, 1, 1, 0x00, 0, 8}, + {FLASH_FLAG_READ_WRITE, SPINOR_OP_READ4, 0, 1, 1, 0x00, 0, 0}, + {0x00, 0, 0, 0, 0, 0x00, 0, 0}, +}; + +/* + * [MX25xxx] Configuration + */ +#define MX25_STATUS_QE (0x1 << 6) + +static int stfsm_mx25_en_32bit_addr_seq(struct stfsm_seq *seq) +{ + seq->seq_opc[0] = (SEQ_OPC_PADS_1 | + SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(SPINOR_OP_EN4B) | + SEQ_OPC_CSDEASSERT); + + seq->seq[0] = STFSM_INST_CMD1; + seq->seq[1] = STFSM_INST_WAIT; + seq->seq[2] = STFSM_INST_STOP; + + seq->seq_cfg = (SEQ_CFG_PADS_1 | + SEQ_CFG_ERASE | + SEQ_CFG_READNOTWRITE | + SEQ_CFG_CSDEASSERT | + SEQ_CFG_STARTSEQ); + + return 0; +} + +/* + * [S25FLxxx] Configuration + */ +#define STFSM_S25FL_CONFIG_QE (0x1 << 1) + +/* + * S25FLxxxS devices provide three ways of supporting 32-bit addressing: Bank + * Register, Extended Address Modes, and a 32-bit address command set. The + * 32-bit address command set is used here, since it avoids any problems with + * entering a state that is incompatible with the SPIBoot Controller. + */ +static struct seq_rw_config stfsm_s25fl_read4_configs[] = { + {FLASH_FLAG_READ_1_4_4, SPINOR_OP_READ4_1_4_4, 0, 4, 4, 0x00, 2, 4}, + {FLASH_FLAG_READ_1_1_4, SPINOR_OP_READ4_1_1_4, 0, 1, 4, 0x00, 0, 8}, + {FLASH_FLAG_READ_1_2_2, SPINOR_OP_READ4_1_2_2, 0, 2, 2, 0x00, 4, 0}, + {FLASH_FLAG_READ_1_1_2, SPINOR_OP_READ4_1_1_2, 0, 1, 2, 0x00, 0, 8}, + {FLASH_FLAG_READ_FAST, SPINOR_OP_READ4_FAST, 0, 1, 1, 0x00, 0, 8}, + {FLASH_FLAG_READ_WRITE, SPINOR_OP_READ4, 0, 1, 1, 0x00, 0, 0}, + {0x00, 0, 0, 0, 0, 0x00, 0, 0}, +}; + +static struct seq_rw_config stfsm_s25fl_write4_configs[] = { + {FLASH_FLAG_WRITE_1_1_4, S25FL_CMD_WRITE4_1_1_4, 1, 1, 4, 0x00, 0, 0}, + {FLASH_FLAG_READ_WRITE, S25FL_CMD_WRITE4, 1, 1, 1, 0x00, 0, 0}, + {0x00, 0, 0, 0, 0, 0x00, 0, 0}, +}; + +/* + * [W25Qxxx] Configuration + */ +#define W25Q_STATUS_QE (0x1 << 1) + +static struct stfsm_seq stfsm_seq_read_jedec = { + .data_size = TRANSFER_SIZE(8), + .seq_opc[0] = (SEQ_OPC_PADS_1 | + SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(SPINOR_OP_RDID)), + .seq = { + STFSM_INST_CMD1, + STFSM_INST_DATA_READ, + STFSM_INST_STOP, + }, + .seq_cfg = (SEQ_CFG_PADS_1 | + SEQ_CFG_READNOTWRITE | + SEQ_CFG_CSDEASSERT | + SEQ_CFG_STARTSEQ), +}; + +static struct stfsm_seq stfsm_seq_read_status_fifo = { + .data_size = TRANSFER_SIZE(4), + .seq_opc[0] = (SEQ_OPC_PADS_1 | + SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(SPINOR_OP_RDSR)), + .seq = { + STFSM_INST_CMD1, + STFSM_INST_DATA_READ, + STFSM_INST_STOP, + }, + .seq_cfg = (SEQ_CFG_PADS_1 | + SEQ_CFG_READNOTWRITE | + SEQ_CFG_CSDEASSERT | + SEQ_CFG_STARTSEQ), +}; + +static struct stfsm_seq stfsm_seq_erase_sector = { + /* 'addr_cfg' configured during initialisation */ + .seq_opc = { + (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(SPINOR_OP_WREN) | SEQ_OPC_CSDEASSERT), + + (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(SPINOR_OP_SE)), + }, + .seq = { + STFSM_INST_CMD1, + STFSM_INST_CMD2, + STFSM_INST_ADD1, + STFSM_INST_ADD2, + STFSM_INST_STOP, + }, + .seq_cfg = (SEQ_CFG_PADS_1 | + SEQ_CFG_READNOTWRITE | + SEQ_CFG_CSDEASSERT | + SEQ_CFG_STARTSEQ), +}; + +static struct stfsm_seq stfsm_seq_erase_chip = { + .seq_opc = { + (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(SPINOR_OP_WREN) | SEQ_OPC_CSDEASSERT), + + (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(SPINOR_OP_CHIP_ERASE) | SEQ_OPC_CSDEASSERT), + }, + .seq = { + STFSM_INST_CMD1, + STFSM_INST_CMD2, + STFSM_INST_WAIT, + STFSM_INST_STOP, + }, + .seq_cfg = (SEQ_CFG_PADS_1 | + SEQ_CFG_ERASE | + SEQ_CFG_READNOTWRITE | + SEQ_CFG_CSDEASSERT | + SEQ_CFG_STARTSEQ), +}; + +static struct stfsm_seq stfsm_seq_write_status = { + .seq_opc[0] = (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(SPINOR_OP_WREN) | SEQ_OPC_CSDEASSERT), + .seq_opc[1] = (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(SPINOR_OP_WRSR)), + .seq = { + STFSM_INST_CMD1, + STFSM_INST_CMD2, + STFSM_INST_STA_WR1, + STFSM_INST_STOP, + }, + .seq_cfg = (SEQ_CFG_PADS_1 | + SEQ_CFG_READNOTWRITE | + SEQ_CFG_CSDEASSERT | + SEQ_CFG_STARTSEQ), +}; + +static int stfsm_n25q_en_32bit_addr_seq(struct stfsm_seq *seq) +{ + seq->seq_opc[0] = (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(SPINOR_OP_EN4B)); + seq->seq_opc[1] = (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(SPINOR_OP_WREN) | + SEQ_OPC_CSDEASSERT); + + seq->seq[0] = STFSM_INST_CMD2; + seq->seq[1] = STFSM_INST_CMD1; + seq->seq[2] = STFSM_INST_WAIT; + seq->seq[3] = STFSM_INST_STOP; + + seq->seq_cfg = (SEQ_CFG_PADS_1 | + SEQ_CFG_ERASE | + SEQ_CFG_READNOTWRITE | + SEQ_CFG_CSDEASSERT | + SEQ_CFG_STARTSEQ); + + return 0; +} + +static inline int stfsm_is_idle(struct stfsm *fsm) +{ + return readl(fsm->base + SPI_FAST_SEQ_STA) & 0x10; +} + +static inline uint32_t stfsm_fifo_available(struct stfsm *fsm) +{ + return (readl(fsm->base + SPI_FAST_SEQ_STA) >> 5) & 0x7f; +} + +static void stfsm_clear_fifo(struct stfsm *fsm) +{ + uint32_t avail; + + for (;;) { + avail = stfsm_fifo_available(fsm); + if (!avail) + break; + + while (avail) { + readl(fsm->base + SPI_FAST_SEQ_DATA_REG); + avail--; + } + } +} + +static inline void stfsm_load_seq(struct stfsm *fsm, + const struct stfsm_seq *seq) +{ + void __iomem *dst = fsm->base + SPI_FAST_SEQ_TRANSFER_SIZE; + const uint32_t *src = (const uint32_t *)seq; + int words = sizeof(*seq) / sizeof(*src); + + BUG_ON(!stfsm_is_idle(fsm)); + + while (words--) { + writel(*src, dst); + src++; + dst += 4; + } +} + +static void stfsm_wait_seq(struct stfsm *fsm) +{ + unsigned long deadline; + int timeout = 0; + + deadline = jiffies + msecs_to_jiffies(STFSM_MAX_WAIT_SEQ_MS); + + while (!timeout) { + if (time_after_eq(jiffies, deadline)) + timeout = 1; + + if (stfsm_is_idle(fsm)) + return; + + cond_resched(); + } + + dev_err(fsm->dev, "timeout on sequence completion\n"); +} + +static void stfsm_read_fifo(struct stfsm *fsm, uint32_t *buf, uint32_t size) +{ + uint32_t remaining = size >> 2; + uint32_t avail; + uint32_t words; + + dev_dbg(fsm->dev, "Reading %d bytes from FIFO\n", size); + + BUG_ON((((uintptr_t)buf) & 0x3) || (size & 0x3)); + + while (remaining) { + for (;;) { + avail = stfsm_fifo_available(fsm); + if (avail) + break; + udelay(1); + } + words = min(avail, remaining); + remaining -= words; + + readsl(fsm->base + SPI_FAST_SEQ_DATA_REG, buf, words); + buf += words; + } +} + +static int stfsm_write_fifo(struct stfsm *fsm, const uint32_t *buf, + uint32_t size) +{ + uint32_t words = size >> 2; + + dev_dbg(fsm->dev, "writing %d bytes to FIFO\n", size); + + BUG_ON((((uintptr_t)buf) & 0x3) || (size & 0x3)); + + writesl(fsm->base + SPI_FAST_SEQ_DATA_REG, buf, words); + + return size; +} + +static int stfsm_enter_32bit_addr(struct stfsm *fsm, int enter) +{ + struct stfsm_seq *seq = &fsm->stfsm_seq_en_32bit_addr; + uint32_t cmd = enter ? SPINOR_OP_EN4B : SPINOR_OP_EX4B; + + seq->seq_opc[0] = (SEQ_OPC_PADS_1 | + SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(cmd) | + SEQ_OPC_CSDEASSERT); + + stfsm_load_seq(fsm, seq); + + stfsm_wait_seq(fsm); + + return 0; +} + +static uint8_t stfsm_wait_busy(struct stfsm *fsm) +{ + struct stfsm_seq *seq = &stfsm_seq_read_status_fifo; + unsigned long deadline; + uint32_t status; + int timeout = 0; + + /* Use RDRS1 */ + seq->seq_opc[0] = (SEQ_OPC_PADS_1 | + SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(SPINOR_OP_RDSR)); + + /* Load read_status sequence */ + stfsm_load_seq(fsm, seq); + + /* + * Repeat until busy bit is deasserted, or timeout, or error (S25FLxxxS) + */ + deadline = jiffies + FLASH_MAX_BUSY_WAIT; + while (!timeout) { + if (time_after_eq(jiffies, deadline)) + timeout = 1; + + stfsm_wait_seq(fsm); + + stfsm_read_fifo(fsm, &status, 4); + + if ((status & FLASH_STATUS_BUSY) == 0) + return 0; + + if ((fsm->configuration & CFG_S25FL_CHECK_ERROR_FLAGS) && + ((status & S25FL_STATUS_P_ERR) || + (status & S25FL_STATUS_E_ERR))) + return (uint8_t)(status & 0xff); + + if (!timeout) + /* Restart */ + writel(seq->seq_cfg, fsm->base + SPI_FAST_SEQ_CFG); + + cond_resched(); + } + + dev_err(fsm->dev, "timeout on wait_busy\n"); + + return FLASH_STATUS_TIMEOUT; +} + +static int stfsm_read_status(struct stfsm *fsm, uint8_t cmd, + uint8_t *data, int bytes) +{ + struct stfsm_seq *seq = &stfsm_seq_read_status_fifo; + uint32_t tmp; + uint8_t *t = (uint8_t *)&tmp; + int i; + + dev_dbg(fsm->dev, "read 'status' register [0x%02x], %d byte(s)\n", + cmd, bytes); + + BUG_ON(bytes != 1 && bytes != 2); + + seq->seq_opc[0] = (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(cmd)), + + stfsm_load_seq(fsm, seq); + + stfsm_read_fifo(fsm, &tmp, 4); + + for (i = 0; i < bytes; i++) + data[i] = t[i]; + + stfsm_wait_seq(fsm); + + return 0; +} + +static int stfsm_write_status(struct stfsm *fsm, uint8_t cmd, + uint16_t data, int bytes, int wait_busy) +{ + struct stfsm_seq *seq = &stfsm_seq_write_status; + + dev_dbg(fsm->dev, + "write 'status' register [0x%02x], %d byte(s), 0x%04x\n" + " %s wait-busy\n", cmd, bytes, data, wait_busy ? "with" : "no"); + + BUG_ON(bytes != 1 && bytes != 2); + + seq->seq_opc[1] = (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(cmd)); + + seq->status = (uint32_t)data | STA_PADS_1 | STA_CSDEASSERT; + seq->seq[2] = (bytes == 1) ? STFSM_INST_STA_WR1 : STFSM_INST_STA_WR1_2; + + stfsm_load_seq(fsm, seq); + + stfsm_wait_seq(fsm); + + if (wait_busy) + stfsm_wait_busy(fsm); + + return 0; +} + +/* + * SoC reset on 'boot-from-spi' systems + * + * Certain modes of operation cause the Flash device to enter a particular state + * for a period of time (e.g. 'Erase Sector', 'Quad Enable', and 'Enter 32-bit + * Addr' commands). On boot-from-spi systems, it is important to consider what + * happens if a warm reset occurs during this period. The SPIBoot controller + * assumes that Flash device is in its default reset state, 24-bit address mode, + * and ready to accept commands. This can be achieved using some form of + * on-board logic/controller to force a device POR in response to a SoC-level + * reset or by making use of the device reset signal if available (limited + * number of devices only). + * + * Failure to take such precautions can cause problems following a warm reset. + * For some operations (e.g. ERASE), there is little that can be done. For + * other modes of operation (e.g. 32-bit addressing), options are often + * available that can help minimise the window in which a reset could cause a + * problem. + * + */ +static bool stfsm_can_handle_soc_reset(struct stfsm *fsm) +{ + /* Reset signal is available on the board and supported by the device */ + if (fsm->reset_signal && fsm->info->flags & FLASH_FLAG_RESET) + return true; + + /* Board-level logic forces a power-on-reset */ + if (fsm->reset_por) + return true; + + /* Reset is not properly handled and may result in failure to reboot */ + return false; +} + +/* Configure 'addr_cfg' according to addressing mode */ +static void stfsm_prepare_erasesec_seq(struct stfsm *fsm, + struct stfsm_seq *seq) +{ + int addr1_cycles = fsm->info->flags & FLASH_FLAG_32BIT_ADDR ? 16 : 8; + + seq->addr_cfg = (ADR_CFG_CYCLES_ADD1(addr1_cycles) | + ADR_CFG_PADS_1_ADD1 | + ADR_CFG_CYCLES_ADD2(16) | + ADR_CFG_PADS_1_ADD2 | + ADR_CFG_CSDEASSERT_ADD2); +} + +/* Search for preferred configuration based on available flags */ +static struct seq_rw_config * +stfsm_search_seq_rw_configs(struct stfsm *fsm, + struct seq_rw_config cfgs[]) +{ + struct seq_rw_config *config; + int flags = fsm->info->flags; + + for (config = cfgs; config->cmd != 0; config++) + if ((config->flags & flags) == config->flags) + return config; + + return NULL; +} + +/* Prepare a READ/WRITE sequence according to configuration parameters */ +static void stfsm_prepare_rw_seq(struct stfsm *fsm, + struct stfsm_seq *seq, + struct seq_rw_config *cfg) +{ + int addr1_cycles, addr2_cycles; + int i = 0; + + memset(seq, 0, sizeof(*seq)); + + /* Add READ/WRITE OPC */ + seq->seq_opc[i++] = (SEQ_OPC_PADS_1 | + SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(cfg->cmd)); + + /* Add WREN OPC for a WRITE sequence */ + if (cfg->write) + seq->seq_opc[i++] = (SEQ_OPC_PADS_1 | + SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(SPINOR_OP_WREN) | + SEQ_OPC_CSDEASSERT); + + /* Address configuration (24 or 32-bit addresses) */ + addr1_cycles = (fsm->info->flags & FLASH_FLAG_32BIT_ADDR) ? 16 : 8; + addr1_cycles /= cfg->addr_pads; + addr2_cycles = 16 / cfg->addr_pads; + seq->addr_cfg = ((addr1_cycles & 0x3f) << 0 | /* ADD1 cycles */ + (cfg->addr_pads - 1) << 6 | /* ADD1 pads */ + (addr2_cycles & 0x3f) << 16 | /* ADD2 cycles */ + ((cfg->addr_pads - 1) << 22)); /* ADD2 pads */ + + /* Data/Sequence configuration */ + seq->seq_cfg = ((cfg->data_pads - 1) << 16 | + SEQ_CFG_STARTSEQ | + SEQ_CFG_CSDEASSERT); + if (!cfg->write) + seq->seq_cfg |= SEQ_CFG_READNOTWRITE; + + /* Mode configuration (no. of pads taken from addr cfg) */ + seq->mode = ((cfg->mode_data & 0xff) << 0 | /* data */ + (cfg->mode_cycles & 0x3f) << 16 | /* cycles */ + (cfg->addr_pads - 1) << 22); /* pads */ + + /* Dummy configuration (no. of pads taken from addr cfg) */ + seq->dummy = ((cfg->dummy_cycles & 0x3f) << 16 | /* cycles */ + (cfg->addr_pads - 1) << 22); /* pads */ + + + /* Instruction sequence */ + i = 0; + if (cfg->write) + seq->seq[i++] = STFSM_INST_CMD2; + + seq->seq[i++] = STFSM_INST_CMD1; + + seq->seq[i++] = STFSM_INST_ADD1; + seq->seq[i++] = STFSM_INST_ADD2; + + if (cfg->mode_cycles) + seq->seq[i++] = STFSM_INST_MODE; + + if (cfg->dummy_cycles) + seq->seq[i++] = STFSM_INST_DUMMY; + + seq->seq[i++] = + cfg->write ? STFSM_INST_DATA_WRITE : STFSM_INST_DATA_READ; + seq->seq[i++] = STFSM_INST_STOP; +} + +static int stfsm_search_prepare_rw_seq(struct stfsm *fsm, + struct stfsm_seq *seq, + struct seq_rw_config *cfgs) +{ + struct seq_rw_config *config; + + config = stfsm_search_seq_rw_configs(fsm, cfgs); + if (!config) { + dev_err(fsm->dev, "failed to find suitable config\n"); + return -EINVAL; + } + + stfsm_prepare_rw_seq(fsm, seq, config); + + return 0; +} + +/* Prepare a READ/WRITE/ERASE 'default' sequences */ +static int stfsm_prepare_rwe_seqs_default(struct stfsm *fsm) +{ + uint32_t flags = fsm->info->flags; + int ret; + + /* Configure 'READ' sequence */ + ret = stfsm_search_prepare_rw_seq(fsm, &fsm->stfsm_seq_read, + default_read_configs); + if (ret) { + dev_err(fsm->dev, + "failed to prep READ sequence with flags [0x%08x]\n", + flags); + return ret; + } + + /* Configure 'WRITE' sequence */ + ret = stfsm_search_prepare_rw_seq(fsm, &fsm->stfsm_seq_write, + default_write_configs); + if (ret) { + dev_err(fsm->dev, + "failed to prep WRITE sequence with flags [0x%08x]\n", + flags); + return ret; + } + + /* Configure 'ERASE_SECTOR' sequence */ + stfsm_prepare_erasesec_seq(fsm, &stfsm_seq_erase_sector); + + return 0; +} + +static int stfsm_mx25_config(struct stfsm *fsm) +{ + uint32_t flags = fsm->info->flags; + uint32_t data_pads; + uint8_t sta; + int ret; + bool soc_reset; + + /* + * Use default READ/WRITE sequences + */ + ret = stfsm_prepare_rwe_seqs_default(fsm); + if (ret) + return ret; + + /* + * Configure 32-bit Address Support + */ + if (flags & FLASH_FLAG_32BIT_ADDR) { + /* Configure 'enter_32bitaddr' FSM sequence */ + stfsm_mx25_en_32bit_addr_seq(&fsm->stfsm_seq_en_32bit_addr); + + soc_reset = stfsm_can_handle_soc_reset(fsm); + if (soc_reset || !fsm->booted_from_spi) + /* If we can handle SoC resets, we enable 32-bit address + * mode pervasively */ + stfsm_enter_32bit_addr(fsm, 1); + + else + /* Else, enable/disable 32-bit addressing before/after + * each operation */ + fsm->configuration = (CFG_READ_TOGGLE_32BIT_ADDR | + CFG_WRITE_TOGGLE_32BIT_ADDR | + CFG_ERASESEC_TOGGLE_32BIT_ADDR); + } + + /* Check status of 'QE' bit, update if required. */ + stfsm_read_status(fsm, SPINOR_OP_RDSR, &sta, 1); + data_pads = ((fsm->stfsm_seq_read.seq_cfg >> 16) & 0x3) + 1; + if (data_pads == 4) { + if (!(sta & MX25_STATUS_QE)) { + /* Set 'QE' */ + sta |= MX25_STATUS_QE; + + stfsm_write_status(fsm, SPINOR_OP_WRSR, sta, 1, 1); + } + } else { + if (sta & MX25_STATUS_QE) { + /* Clear 'QE' */ + sta &= ~MX25_STATUS_QE; + + stfsm_write_status(fsm, SPINOR_OP_WRSR, sta, 1, 1); + } + } + + return 0; +} + +static int stfsm_n25q_config(struct stfsm *fsm) +{ + uint32_t flags = fsm->info->flags; + uint8_t vcr; + int ret = 0; + bool soc_reset; + + /* Configure 'READ' sequence */ + if (flags & FLASH_FLAG_32BIT_ADDR) + ret = stfsm_search_prepare_rw_seq(fsm, &fsm->stfsm_seq_read, + n25q_read4_configs); + else + ret = stfsm_search_prepare_rw_seq(fsm, &fsm->stfsm_seq_read, + n25q_read3_configs); + if (ret) { + dev_err(fsm->dev, + "failed to prepare READ sequence with flags [0x%08x]\n", + flags); + return ret; + } + + /* Configure 'WRITE' sequence (default configs) */ + ret = stfsm_search_prepare_rw_seq(fsm, &fsm->stfsm_seq_write, + default_write_configs); + if (ret) { + dev_err(fsm->dev, + "preparing WRITE sequence using flags [0x%08x] failed\n", + flags); + return ret; + } + + /* * Configure 'ERASE_SECTOR' sequence */ + stfsm_prepare_erasesec_seq(fsm, &stfsm_seq_erase_sector); + + /* Configure 32-bit address support */ + if (flags & FLASH_FLAG_32BIT_ADDR) { + stfsm_n25q_en_32bit_addr_seq(&fsm->stfsm_seq_en_32bit_addr); + + soc_reset = stfsm_can_handle_soc_reset(fsm); + if (soc_reset || !fsm->booted_from_spi) { + /* + * If we can handle SoC resets, we enable 32-bit + * address mode pervasively + */ + stfsm_enter_32bit_addr(fsm, 1); + } else { + /* + * If not, enable/disable for WRITE and ERASE + * operations (READ uses special commands) + */ + fsm->configuration = (CFG_WRITE_TOGGLE_32BIT_ADDR | + CFG_ERASESEC_TOGGLE_32BIT_ADDR); + } + } + + /* + * Configure device to use 8 dummy cycles + */ + vcr = (N25Q_VCR_DUMMY_CYCLES(8) | N25Q_VCR_XIP_DISABLED | + N25Q_VCR_WRAP_CONT); + stfsm_write_status(fsm, N25Q_CMD_WRVCR, vcr, 1, 0); + + return 0; +} + +static void stfsm_s25fl_prepare_erasesec_seq_32(struct stfsm_seq *seq) +{ + seq->seq_opc[1] = (SEQ_OPC_PADS_1 | + SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(S25FL_CMD_SE4)); + + seq->addr_cfg = (ADR_CFG_CYCLES_ADD1(16) | + ADR_CFG_PADS_1_ADD1 | + ADR_CFG_CYCLES_ADD2(16) | + ADR_CFG_PADS_1_ADD2 | + ADR_CFG_CSDEASSERT_ADD2); +} + +static void stfsm_s25fl_read_dyb(struct stfsm *fsm, uint32_t offs, uint8_t *dby) +{ + uint32_t tmp; + struct stfsm_seq seq = { + .data_size = TRANSFER_SIZE(4), + .seq_opc[0] = (SEQ_OPC_PADS_1 | + SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(S25FL_CMD_DYBRD)), + .addr_cfg = (ADR_CFG_CYCLES_ADD1(16) | + ADR_CFG_PADS_1_ADD1 | + ADR_CFG_CYCLES_ADD2(16) | + ADR_CFG_PADS_1_ADD2), + .addr1 = (offs >> 16) & 0xffff, + .addr2 = offs & 0xffff, + .seq = { + STFSM_INST_CMD1, + STFSM_INST_ADD1, + STFSM_INST_ADD2, + STFSM_INST_DATA_READ, + STFSM_INST_STOP, + }, + .seq_cfg = (SEQ_CFG_PADS_1 | + SEQ_CFG_READNOTWRITE | + SEQ_CFG_CSDEASSERT | + SEQ_CFG_STARTSEQ), + }; + + stfsm_load_seq(fsm, &seq); + + stfsm_read_fifo(fsm, &tmp, 4); + + *dby = (uint8_t)(tmp >> 24); + + stfsm_wait_seq(fsm); +} + +static void stfsm_s25fl_write_dyb(struct stfsm *fsm, uint32_t offs, uint8_t dby) +{ + struct stfsm_seq seq = { + .seq_opc[0] = (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(SPINOR_OP_WREN) | + SEQ_OPC_CSDEASSERT), + .seq_opc[1] = (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(S25FL_CMD_DYBWR)), + .addr_cfg = (ADR_CFG_CYCLES_ADD1(16) | + ADR_CFG_PADS_1_ADD1 | + ADR_CFG_CYCLES_ADD2(16) | + ADR_CFG_PADS_1_ADD2), + .status = (uint32_t)dby | STA_PADS_1 | STA_CSDEASSERT, + .addr1 = (offs >> 16) & 0xffff, + .addr2 = offs & 0xffff, + .seq = { + STFSM_INST_CMD1, + STFSM_INST_CMD2, + STFSM_INST_ADD1, + STFSM_INST_ADD2, + STFSM_INST_STA_WR1, + STFSM_INST_STOP, + }, + .seq_cfg = (SEQ_CFG_PADS_1 | + SEQ_CFG_READNOTWRITE | + SEQ_CFG_CSDEASSERT | + SEQ_CFG_STARTSEQ), + }; + + stfsm_load_seq(fsm, &seq); + stfsm_wait_seq(fsm); + + stfsm_wait_busy(fsm); +} + +static int stfsm_s25fl_clear_status_reg(struct stfsm *fsm) +{ + struct stfsm_seq seq = { + .seq_opc[0] = (SEQ_OPC_PADS_1 | + SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(S25FL_CMD_CLSR) | + SEQ_OPC_CSDEASSERT), + .seq_opc[1] = (SEQ_OPC_PADS_1 | + SEQ_OPC_CYCLES(8) | + SEQ_OPC_OPCODE(SPINOR_OP_WRDI) | + SEQ_OPC_CSDEASSERT), + .seq = { + STFSM_INST_CMD1, + STFSM_INST_CMD2, + STFSM_INST_WAIT, + STFSM_INST_STOP, + }, + .seq_cfg = (SEQ_CFG_PADS_1 | + SEQ_CFG_ERASE | + SEQ_CFG_READNOTWRITE | + SEQ_CFG_CSDEASSERT | + SEQ_CFG_STARTSEQ), + }; + + stfsm_load_seq(fsm, &seq); + + stfsm_wait_seq(fsm); + + return 0; +} + +static int stfsm_s25fl_config(struct stfsm *fsm) +{ + struct flash_info *info = fsm->info; + uint32_t flags = info->flags; + uint32_t data_pads; + uint32_t offs; + uint16_t sta_wr; + uint8_t sr1, cr1, dyb; + int update_sr = 0; + int ret; + + if (flags & FLASH_FLAG_32BIT_ADDR) { + /* + * Prepare Read/Write/Erase sequences according to S25FLxxx + * 32-bit address command set + */ + ret = stfsm_search_prepare_rw_seq(fsm, &fsm->stfsm_seq_read, + stfsm_s25fl_read4_configs); + if (ret) + return ret; + + ret = stfsm_search_prepare_rw_seq(fsm, &fsm->stfsm_seq_write, + stfsm_s25fl_write4_configs); + if (ret) + return ret; + + stfsm_s25fl_prepare_erasesec_seq_32(&stfsm_seq_erase_sector); + + } else { + /* Use default configurations for 24-bit addressing */ + ret = stfsm_prepare_rwe_seqs_default(fsm); + if (ret) + return ret; + } + + /* + * For devices that support 'DYB' sector locking, check lock status and + * unlock sectors if necessary (some variants power-on with sectors + * locked by default) + */ + if (flags & FLASH_FLAG_DYB_LOCKING) { + offs = 0; + for (offs = 0; offs < info->sector_size * info->n_sectors;) { + stfsm_s25fl_read_dyb(fsm, offs, &dyb); + if (dyb == 0x00) + stfsm_s25fl_write_dyb(fsm, offs, 0xff); + + /* Handle bottom/top 4KiB parameter sectors */ + if ((offs < info->sector_size * 2) || + (offs >= (info->sector_size - info->n_sectors * 4))) + offs += 0x1000; + else + offs += 0x10000; + } + } + + /* Check status of 'QE' bit, update if required. */ + stfsm_read_status(fsm, SPINOR_OP_RDSR2, &cr1, 1); + data_pads = ((fsm->stfsm_seq_read.seq_cfg >> 16) & 0x3) + 1; + if (data_pads == 4) { + if (!(cr1 & STFSM_S25FL_CONFIG_QE)) { + /* Set 'QE' */ + cr1 |= STFSM_S25FL_CONFIG_QE; + + update_sr = 1; + } + } else { + if (cr1 & STFSM_S25FL_CONFIG_QE) { + /* Clear 'QE' */ + cr1 &= ~STFSM_S25FL_CONFIG_QE; + + update_sr = 1; + } + } + if (update_sr) { + stfsm_read_status(fsm, SPINOR_OP_RDSR, &sr1, 1); + sta_wr = ((uint16_t)cr1 << 8) | sr1; + stfsm_write_status(fsm, SPINOR_OP_WRSR, sta_wr, 2, 1); + } + + /* + * S25FLxxx devices support Program and Error error flags. + * Configure driver to check flags and clear if necessary. + */ + fsm->configuration |= CFG_S25FL_CHECK_ERROR_FLAGS; + + return 0; +} + +static int stfsm_w25q_config(struct stfsm *fsm) +{ + uint32_t data_pads; + uint8_t sr1, sr2; + uint16_t sr_wr; + int update_sr = 0; + int ret; + + ret = stfsm_prepare_rwe_seqs_default(fsm); + if (ret) + return ret; + + /* Check status of 'QE' bit, update if required. */ + stfsm_read_status(fsm, SPINOR_OP_RDSR2, &sr2, 1); + data_pads = ((fsm->stfsm_seq_read.seq_cfg >> 16) & 0x3) + 1; + if (data_pads == 4) { + if (!(sr2 & W25Q_STATUS_QE)) { + /* Set 'QE' */ + sr2 |= W25Q_STATUS_QE; + update_sr = 1; + } + } else { + if (sr2 & W25Q_STATUS_QE) { + /* Clear 'QE' */ + sr2 &= ~W25Q_STATUS_QE; + update_sr = 1; + } + } + if (update_sr) { + /* Write status register */ + stfsm_read_status(fsm, SPINOR_OP_RDSR, &sr1, 1); + sr_wr = ((uint16_t)sr2 << 8) | sr1; + stfsm_write_status(fsm, SPINOR_OP_WRSR, sr_wr, 2, 1); + } + + return 0; +} + +static int stfsm_read(struct stfsm *fsm, uint8_t *buf, uint32_t size, + uint32_t offset) +{ + struct stfsm_seq *seq = &fsm->stfsm_seq_read; + uint32_t data_pads; + uint32_t read_mask; + uint32_t size_ub; + uint32_t size_lb; + uint32_t size_mop; + uint32_t tmp[4]; + uint32_t page_buf[FLASH_PAGESIZE_32]; + uint8_t *p; + + dev_dbg(fsm->dev, "reading %d bytes from 0x%08x\n", size, offset); + + /* Enter 32-bit address mode, if required */ + if (fsm->configuration & CFG_READ_TOGGLE_32BIT_ADDR) + stfsm_enter_32bit_addr(fsm, 1); + + /* Must read in multiples of 32 cycles (or 32*pads/8 Bytes) */ + data_pads = ((seq->seq_cfg >> 16) & 0x3) + 1; + read_mask = (data_pads << 2) - 1; + + /* Handle non-aligned buf */ + p = ((uintptr_t)buf & 0x3) ? (uint8_t *)page_buf : buf; + + /* Handle non-aligned size */ + size_ub = (size + read_mask) & ~read_mask; + size_lb = size & ~read_mask; + size_mop = size & read_mask; + + seq->data_size = TRANSFER_SIZE(size_ub); + seq->addr1 = (offset >> 16) & 0xffff; + seq->addr2 = offset & 0xffff; + + stfsm_load_seq(fsm, seq); + + if (size_lb) + stfsm_read_fifo(fsm, (uint32_t *)p, size_lb); + + if (size_mop) { + stfsm_read_fifo(fsm, tmp, read_mask + 1); + memcpy(p + size_lb, &tmp, size_mop); + } + + /* Handle non-aligned buf */ + if ((uintptr_t)buf & 0x3) + memcpy(buf, page_buf, size); + + /* Wait for sequence to finish */ + stfsm_wait_seq(fsm); + + stfsm_clear_fifo(fsm); + + /* Exit 32-bit address mode, if required */ + if (fsm->configuration & CFG_READ_TOGGLE_32BIT_ADDR) + stfsm_enter_32bit_addr(fsm, 0); + + return 0; +} + +static int stfsm_write(struct stfsm *fsm, const uint8_t *buf, + uint32_t size, uint32_t offset) +{ + struct stfsm_seq *seq = &fsm->stfsm_seq_write; + uint32_t data_pads; + uint32_t write_mask; + uint32_t size_ub; + uint32_t size_lb; + uint32_t size_mop; + uint32_t tmp[4]; + uint32_t page_buf[FLASH_PAGESIZE_32]; + uint8_t *t = (uint8_t *)&tmp; + const uint8_t *p; + int ret; + int i; + + dev_dbg(fsm->dev, "writing %d bytes to 0x%08x\n", size, offset); + + /* Enter 32-bit address mode, if required */ + if (fsm->configuration & CFG_WRITE_TOGGLE_32BIT_ADDR) + stfsm_enter_32bit_addr(fsm, 1); + + /* Must write in multiples of 32 cycles (or 32*pads/8 bytes) */ + data_pads = ((seq->seq_cfg >> 16) & 0x3) + 1; + write_mask = (data_pads << 2) - 1; + + /* Handle non-aligned buf */ + if ((uintptr_t)buf & 0x3) { + memcpy(page_buf, buf, size); + p = (uint8_t *)page_buf; + } else { + p = buf; + } + + /* Handle non-aligned size */ + size_ub = (size + write_mask) & ~write_mask; + size_lb = size & ~write_mask; + size_mop = size & write_mask; + + seq->data_size = TRANSFER_SIZE(size_ub); + seq->addr1 = (offset >> 16) & 0xffff; + seq->addr2 = offset & 0xffff; + + /* Need to set FIFO to write mode, before writing data to FIFO (see + * GNBvb79594) + */ + writel(0x00040000, fsm->base + SPI_FAST_SEQ_CFG); + + /* + * Before writing data to the FIFO, apply a small delay to allow a + * potential change of FIFO direction to complete. + */ + if (fsm->fifo_dir_delay == 0) + readl(fsm->base + SPI_FAST_SEQ_CFG); + else + udelay(fsm->fifo_dir_delay); + + + /* Write data to FIFO, before starting sequence (see GNBvd79593) */ + if (size_lb) { + stfsm_write_fifo(fsm, (uint32_t *)p, size_lb); + p += size_lb; + } + + /* Handle non-aligned size */ + if (size_mop) { + memset(t, 0xff, write_mask + 1); /* fill with 0xff's */ + for (i = 0; i < size_mop; i++) + t[i] = *p++; + + stfsm_write_fifo(fsm, tmp, write_mask + 1); + } + + /* Start sequence */ + stfsm_load_seq(fsm, seq); + + /* Wait for sequence to finish */ + stfsm_wait_seq(fsm); + + /* Wait for completion */ + ret = stfsm_wait_busy(fsm); + if (ret && fsm->configuration & CFG_S25FL_CHECK_ERROR_FLAGS) + stfsm_s25fl_clear_status_reg(fsm); + + /* Exit 32-bit address mode, if required */ + if (fsm->configuration & CFG_WRITE_TOGGLE_32BIT_ADDR) + stfsm_enter_32bit_addr(fsm, 0); + + return 0; +} + +/* + * Read an address range from the flash chip. The address range + * may be any size provided it is within the physical boundaries. + */ +static int stfsm_mtd_read(struct mtd_info *mtd, loff_t from, size_t len, + size_t *retlen, u_char *buf) +{ + struct stfsm *fsm = dev_get_drvdata(mtd->dev.parent); + uint32_t bytes; + + dev_dbg(fsm->dev, "%s from 0x%08x, len %zd\n", + __func__, (u32)from, len); + + mutex_lock(&fsm->lock); + + while (len > 0) { + bytes = min_t(size_t, len, FLASH_PAGESIZE); + + stfsm_read(fsm, buf, bytes, from); + + buf += bytes; + from += bytes; + len -= bytes; + + *retlen += bytes; + } + + mutex_unlock(&fsm->lock); + + return 0; +} + +static int stfsm_erase_sector(struct stfsm *fsm, uint32_t offset) +{ + struct stfsm_seq *seq = &stfsm_seq_erase_sector; + int ret; + + dev_dbg(fsm->dev, "erasing sector at 0x%08x\n", offset); + + /* Enter 32-bit address mode, if required */ + if (fsm->configuration & CFG_ERASESEC_TOGGLE_32BIT_ADDR) + stfsm_enter_32bit_addr(fsm, 1); + + seq->addr1 = (offset >> 16) & 0xffff; + seq->addr2 = offset & 0xffff; + + stfsm_load_seq(fsm, seq); + + stfsm_wait_seq(fsm); + + /* Wait for completion */ + ret = stfsm_wait_busy(fsm); + if (ret && fsm->configuration & CFG_S25FL_CHECK_ERROR_FLAGS) + stfsm_s25fl_clear_status_reg(fsm); + + /* Exit 32-bit address mode, if required */ + if (fsm->configuration & CFG_ERASESEC_TOGGLE_32BIT_ADDR) + stfsm_enter_32bit_addr(fsm, 0); + + return ret; +} + +static int stfsm_erase_chip(struct stfsm *fsm) +{ + const struct stfsm_seq *seq = &stfsm_seq_erase_chip; + + dev_dbg(fsm->dev, "erasing chip\n"); + + stfsm_load_seq(fsm, seq); + + stfsm_wait_seq(fsm); + + return stfsm_wait_busy(fsm); +} + +/* + * Write an address range to the flash chip. Data must be written in + * FLASH_PAGESIZE chunks. The address range may be any size provided + * it is within the physical boundaries. + */ +static int stfsm_mtd_write(struct mtd_info *mtd, loff_t to, size_t len, + size_t *retlen, const u_char *buf) +{ + struct stfsm *fsm = dev_get_drvdata(mtd->dev.parent); + + u32 page_offs; + u32 bytes; + uint8_t *b = (uint8_t *)buf; + int ret = 0; + + dev_dbg(fsm->dev, "%s to 0x%08x, len %zd\n", __func__, (u32)to, len); + + /* Offset within page */ + page_offs = to % FLASH_PAGESIZE; + + mutex_lock(&fsm->lock); + + while (len) { + /* Write up to page boundary */ + bytes = min_t(size_t, FLASH_PAGESIZE - page_offs, len); + + ret = stfsm_write(fsm, b, bytes, to); + if (ret) + goto out1; + + b += bytes; + len -= bytes; + to += bytes; + + /* We are now page-aligned */ + page_offs = 0; + + *retlen += bytes; + + } + +out1: + mutex_unlock(&fsm->lock); + + return ret; +} + +/* + * Erase an address range on the flash chip. The address range may extend + * one or more erase sectors. Return an error is there is a problem erasing. + */ +static int stfsm_mtd_erase(struct mtd_info *mtd, struct erase_info *instr) +{ + struct stfsm *fsm = dev_get_drvdata(mtd->dev.parent); + u32 addr, len; + int ret; + + dev_dbg(fsm->dev, "%s at 0x%llx, len %lld\n", __func__, + (long long)instr->addr, (long long)instr->len); + + addr = instr->addr; + len = instr->len; + + mutex_lock(&fsm->lock); + + /* Whole-chip erase? */ + if (len == mtd->size) { + ret = stfsm_erase_chip(fsm); + if (ret) + goto out1; + } else { + while (len) { + ret = stfsm_erase_sector(fsm, addr); + if (ret) + goto out1; + + addr += mtd->erasesize; + len -= mtd->erasesize; + } + } + + mutex_unlock(&fsm->lock); + + instr->state = MTD_ERASE_DONE; + mtd_erase_callback(instr); + + return 0; + +out1: + instr->state = MTD_ERASE_FAILED; + mutex_unlock(&fsm->lock); + + return ret; +} + +static void stfsm_read_jedec(struct stfsm *fsm, uint8_t *jedec) +{ + const struct stfsm_seq *seq = &stfsm_seq_read_jedec; + uint32_t tmp[2]; + + stfsm_load_seq(fsm, seq); + + stfsm_read_fifo(fsm, tmp, 8); + + memcpy(jedec, tmp, 5); + + stfsm_wait_seq(fsm); +} + +static struct flash_info *stfsm_jedec_probe(struct stfsm *fsm) +{ + struct flash_info *info; + u16 ext_jedec; + u32 jedec; + u8 id[5]; + + stfsm_read_jedec(fsm, id); + + jedec = id[0] << 16 | id[1] << 8 | id[2]; + /* + * JEDEC also defines an optional "extended device information" + * string for after vendor-specific data, after the three bytes + * we use here. Supporting some chips might require using it. + */ + ext_jedec = id[3] << 8 | id[4]; + + dev_dbg(fsm->dev, "JEDEC = 0x%08x [%02x %02x %02x %02x %02x]\n", + jedec, id[0], id[1], id[2], id[3], id[4]); + + for (info = flash_types; info->name; info++) { + if (info->jedec_id == jedec) { + if (info->ext_id && info->ext_id != ext_jedec) + continue; + return info; + } + } + dev_err(fsm->dev, "Unrecognized JEDEC id %06x\n", jedec); + + return NULL; +} + +static int stfsm_set_mode(struct stfsm *fsm, uint32_t mode) +{ + int ret, timeout = 10; + + /* Wait for controller to accept mode change */ + while (--timeout) { + ret = readl(fsm->base + SPI_STA_MODE_CHANGE); + if (ret & 0x1) + break; + udelay(1); + } + + if (!timeout) + return -EBUSY; + + writel(mode, fsm->base + SPI_MODESELECT); + + return 0; +} + +static void stfsm_set_freq(struct stfsm *fsm, uint32_t spi_freq) +{ + uint32_t emi_freq; + uint32_t clk_div; + + /* TODO: Make this dynamic */ + emi_freq = STFSM_DEFAULT_EMI_FREQ; + + /* + * Calculate clk_div - values between 2 and 128 + * Multiple of 2, rounded up + */ + clk_div = 2 * DIV_ROUND_UP(emi_freq, 2 * spi_freq); + if (clk_div < 2) + clk_div = 2; + else if (clk_div > 128) + clk_div = 128; + + /* + * Determine a suitable delay for the IP to complete a change of + * direction of the FIFO. The required delay is related to the clock + * divider used. The following heuristics are based on empirical tests, + * using a 100MHz EMI clock. + */ + if (clk_div <= 4) + fsm->fifo_dir_delay = 0; + else if (clk_div <= 10) + fsm->fifo_dir_delay = 1; + else + fsm->fifo_dir_delay = DIV_ROUND_UP(clk_div, 10); + + dev_dbg(fsm->dev, "emi_clk = %uHZ, spi_freq = %uHZ, clk_div = %u\n", + emi_freq, spi_freq, clk_div); + + writel(clk_div, fsm->base + SPI_CLOCKDIV); +} + +static int stfsm_init(struct stfsm *fsm) +{ + int ret; + + /* Perform a soft reset of the FSM controller */ + writel(SEQ_CFG_SWRESET, fsm->base + SPI_FAST_SEQ_CFG); + udelay(1); + writel(0, fsm->base + SPI_FAST_SEQ_CFG); + + /* Set clock to 'safe' frequency initially */ + stfsm_set_freq(fsm, STFSM_FLASH_SAFE_FREQ); + + /* Switch to FSM */ + ret = stfsm_set_mode(fsm, SPI_MODESELECT_FSM); + if (ret) + return ret; + + /* Set timing parameters */ + writel(SPI_CFG_DEVICE_ST | + SPI_CFG_DEFAULT_MIN_CS_HIGH | + SPI_CFG_DEFAULT_CS_SETUPHOLD | + SPI_CFG_DEFAULT_DATA_HOLD, + fsm->base + SPI_CONFIGDATA); + writel(STFSM_DEFAULT_WR_TIME, fsm->base + SPI_STATUS_WR_TIME_REG); + + /* + * Set the FSM 'WAIT' delay to the minimum workable value. Note, for + * our purposes, the WAIT instruction is used purely to achieve + * "sequence validity" rather than actually implement a delay. + */ + writel(0x00000001, fsm->base + SPI_PROGRAM_ERASE_TIME); + + /* Clear FIFO, just in case */ + stfsm_clear_fifo(fsm); + + return 0; +} + +static void stfsm_fetch_platform_configs(struct platform_device *pdev) +{ + struct stfsm *fsm = platform_get_drvdata(pdev); + struct device_node *np = pdev->dev.of_node; + struct regmap *regmap; + uint32_t boot_device_reg; + uint32_t boot_device_spi; + uint32_t boot_device; /* Value we read from *boot_device_reg */ + int ret; + + /* Booting from SPI NOR Flash is the default */ + fsm->booted_from_spi = true; + + regmap = syscon_regmap_lookup_by_phandle(np, "st,syscfg"); + if (IS_ERR(regmap)) + goto boot_device_fail; + + fsm->reset_signal = of_property_read_bool(np, "st,reset-signal"); + + fsm->reset_por = of_property_read_bool(np, "st,reset-por"); + + /* Where in the syscon the boot device information lives */ + ret = of_property_read_u32(np, "st,boot-device-reg", &boot_device_reg); + if (ret) + goto boot_device_fail; + + /* Boot device value when booted from SPI NOR */ + ret = of_property_read_u32(np, "st,boot-device-spi", &boot_device_spi); + if (ret) + goto boot_device_fail; + + ret = regmap_read(regmap, boot_device_reg, &boot_device); + if (ret) + goto boot_device_fail; + + if (boot_device != boot_device_spi) + fsm->booted_from_spi = false; + + return; + +boot_device_fail: + dev_warn(&pdev->dev, + "failed to fetch boot device, assuming boot from SPI\n"); +} + +static int stfsm_probe(struct platform_device *pdev) +{ + struct device_node *np = pdev->dev.of_node; + struct mtd_part_parser_data ppdata; + struct flash_info *info; + struct resource *res; + struct stfsm *fsm; + int ret; + + if (!np) { + dev_err(&pdev->dev, "No DT found\n"); + return -EINVAL; + } + ppdata.of_node = np; + + fsm = devm_kzalloc(&pdev->dev, sizeof(*fsm), GFP_KERNEL); + if (!fsm) + return -ENOMEM; + + fsm->dev = &pdev->dev; + + platform_set_drvdata(pdev, fsm); + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + dev_err(&pdev->dev, "Resource not found\n"); + return -ENODEV; + } + + fsm->base = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(fsm->base)) { + dev_err(&pdev->dev, + "Failed to reserve memory region %pR\n", res); + return PTR_ERR(fsm->base); + } + + mutex_init(&fsm->lock); + + ret = stfsm_init(fsm); + if (ret) { + dev_err(&pdev->dev, "Failed to initialise FSM Controller\n"); + return ret; + } + + stfsm_fetch_platform_configs(pdev); + + /* Detect SPI FLASH device */ + info = stfsm_jedec_probe(fsm); + if (!info) + return -ENODEV; + fsm->info = info; + + /* Use device size to determine address width */ + if (info->sector_size * info->n_sectors > 0x1000000) + info->flags |= FLASH_FLAG_32BIT_ADDR; + + /* + * Configure READ/WRITE/ERASE sequences according to platform and + * device flags. + */ + if (info->config) { + ret = info->config(fsm); + if (ret) + return ret; + } else { + ret = stfsm_prepare_rwe_seqs_default(fsm); + if (ret) + return ret; + } + + fsm->mtd.name = info->name; + fsm->mtd.dev.parent = &pdev->dev; + fsm->mtd.type = MTD_NORFLASH; + fsm->mtd.writesize = 4; + fsm->mtd.writebufsize = fsm->mtd.writesize; + fsm->mtd.flags = MTD_CAP_NORFLASH; + fsm->mtd.size = info->sector_size * info->n_sectors; + fsm->mtd.erasesize = info->sector_size; + + fsm->mtd._read = stfsm_mtd_read; + fsm->mtd._write = stfsm_mtd_write; + fsm->mtd._erase = stfsm_mtd_erase; + + dev_info(&pdev->dev, + "Found serial flash device: %s\n" + " size = %llx (%lldMiB) erasesize = 0x%08x (%uKiB)\n", + info->name, + (long long)fsm->mtd.size, (long long)(fsm->mtd.size >> 20), + fsm->mtd.erasesize, (fsm->mtd.erasesize >> 10)); + + return mtd_device_parse_register(&fsm->mtd, NULL, &ppdata, NULL, 0); +} + +static int stfsm_remove(struct platform_device *pdev) +{ + struct stfsm *fsm = platform_get_drvdata(pdev); + + return mtd_device_unregister(&fsm->mtd); +} + +static const struct of_device_id stfsm_match[] = { + { .compatible = "st,spi-fsm", }, + {}, +}; +MODULE_DEVICE_TABLE(of, stfsm_match); + +static struct platform_driver stfsm_driver = { + .probe = stfsm_probe, + .remove = stfsm_remove, + .driver = { + .name = "st-spi-fsm", + .owner = THIS_MODULE, + .of_match_table = stfsm_match, + }, +}; +module_platform_driver(stfsm_driver); + +MODULE_AUTHOR("Angus Clark <angus.clark@st.com>"); +MODULE_DESCRIPTION("ST SPI FSM driver"); +MODULE_LICENSE("GPL"); |