diff options
Diffstat (limited to 'drivers/mtd/devices')
| -rw-r--r-- | drivers/mtd/devices/Kconfig | 13 | ||||
| -rw-r--r-- | drivers/mtd/devices/Makefile | 3 | ||||
| -rw-r--r-- | drivers/mtd/devices/doc2000.c | 17 | ||||
| -rw-r--r-- | drivers/mtd/devices/doc2001.c | 11 | ||||
| -rw-r--r-- | drivers/mtd/devices/doc2001plus.c | 11 | ||||
| -rw-r--r-- | drivers/mtd/devices/docecc.c | 2 | ||||
| -rw-r--r-- | drivers/mtd/devices/docg3.c | 1114 | ||||
| -rw-r--r-- | drivers/mtd/devices/docg3.h | 297 | ||||
| -rw-r--r-- | drivers/mtd/devices/docprobe.c | 5 | ||||
| -rw-r--r-- | drivers/mtd/devices/lart.c | 18 | ||||
| -rw-r--r-- | drivers/mtd/devices/m25p80.c | 92 | ||||
| -rw-r--r-- | drivers/mtd/devices/mtd_dataflash.c | 91 | ||||
| -rw-r--r-- | drivers/mtd/devices/sst25l.c | 42 |
13 files changed, 1521 insertions, 195 deletions
diff --git a/drivers/mtd/devices/Kconfig b/drivers/mtd/devices/Kconfig index 35081ce77fb..283d887f782 100644 --- a/drivers/mtd/devices/Kconfig +++ b/drivers/mtd/devices/Kconfig @@ -249,6 +249,16 @@ config MTD_DOC2001PLUS under "NAND Flash Device Drivers" (currently that driver does not support all Millennium Plus devices). +config MTD_DOCG3 + tristate "M-Systems Disk-On-Chip G3" + ---help--- + This provides an MTD device driver for the M-Systems DiskOnChip + G3 devices. + + The driver provides access to G3 DiskOnChip, distributed by + M-Systems and now Sandisk. The support is very experimental, + and doesn't give access to any write operations. + config MTD_DOCPROBE tristate select MTD_DOCECC @@ -268,8 +278,7 @@ config MTD_DOCPROBE_ADVANCED config MTD_DOCPROBE_ADDRESS hex "Physical address of DiskOnChip" if MTD_DOCPROBE_ADVANCED depends on MTD_DOCPROBE - default "0x0000" if MTD_DOCPROBE_ADVANCED - default "0" if !MTD_DOCPROBE_ADVANCED + default "0x0" ---help--- By default, the probe for DiskOnChip devices will look for a DiskOnChip at every multiple of 0x2000 between 0xC8000 and 0xEE000. diff --git a/drivers/mtd/devices/Makefile b/drivers/mtd/devices/Makefile index f3226b1d38f..56c7cd462f1 100644 --- a/drivers/mtd/devices/Makefile +++ b/drivers/mtd/devices/Makefile @@ -5,6 +5,7 @@ obj-$(CONFIG_MTD_DOC2000) += doc2000.o obj-$(CONFIG_MTD_DOC2001) += doc2001.o obj-$(CONFIG_MTD_DOC2001PLUS) += doc2001plus.o +obj-$(CONFIG_MTD_DOCG3) += docg3.o obj-$(CONFIG_MTD_DOCPROBE) += docprobe.o obj-$(CONFIG_MTD_DOCECC) += docecc.o obj-$(CONFIG_MTD_SLRAM) += slram.o @@ -17,3 +18,5 @@ obj-$(CONFIG_MTD_BLOCK2MTD) += block2mtd.o obj-$(CONFIG_MTD_DATAFLASH) += mtd_dataflash.o obj-$(CONFIG_MTD_M25P80) += m25p80.o obj-$(CONFIG_MTD_SST25L) += sst25l.o + +CFLAGS_docg3.o += -I$(src)
\ No newline at end of file diff --git a/drivers/mtd/devices/doc2000.c b/drivers/mtd/devices/doc2000.c index f7fbf6025ef..e9fad915121 100644 --- a/drivers/mtd/devices/doc2000.c +++ b/drivers/mtd/devices/doc2000.c @@ -82,8 +82,7 @@ static int _DoC_WaitReady(struct DiskOnChip *doc) void __iomem *docptr = doc->virtadr; unsigned long timeo = jiffies + (HZ * 10); - DEBUG(MTD_DEBUG_LEVEL3, - "_DoC_WaitReady called for out-of-line wait\n"); + pr_debug("_DoC_WaitReady called for out-of-line wait\n"); /* Out-of-line routine to wait for chip response */ while (!(ReadDOC(docptr, CDSNControl) & CDSN_CTRL_FR_B)) { @@ -92,7 +91,7 @@ static int _DoC_WaitReady(struct DiskOnChip *doc) DoC_Delay(doc, 2); if (time_after(jiffies, timeo)) { - DEBUG(MTD_DEBUG_LEVEL2, "_DoC_WaitReady timed out.\n"); + pr_debug("_DoC_WaitReady timed out.\n"); return -EIO; } udelay(1); @@ -323,8 +322,7 @@ static int DoC_IdentChip(struct DiskOnChip *doc, int floor, int chip) /* Reset the chip */ if (DoC_Command(doc, NAND_CMD_RESET, CDSN_CTRL_WP)) { - DEBUG(MTD_DEBUG_LEVEL2, - "DoC_Command (reset) for %d,%d returned true\n", + pr_debug("DoC_Command (reset) for %d,%d returned true\n", floor, chip); return 0; } @@ -332,8 +330,7 @@ static int DoC_IdentChip(struct DiskOnChip *doc, int floor, int chip) /* Read the NAND chip ID: 1. Send ReadID command */ if (DoC_Command(doc, NAND_CMD_READID, CDSN_CTRL_WP)) { - DEBUG(MTD_DEBUG_LEVEL2, - "DoC_Command (ReadID) for %d,%d returned true\n", + pr_debug("DoC_Command (ReadID) for %d,%d returned true\n", floor, chip); return 0; } @@ -699,7 +696,7 @@ static int doc_read(struct mtd_info *mtd, loff_t from, size_t len, #ifdef ECC_DEBUG printk(KERN_ERR "DiskOnChip ECC Error: Read at %lx\n", (long)from); #endif - /* Read the ECC syndrom through the DiskOnChip ECC + /* Read the ECC syndrome through the DiskOnChip ECC logic. These syndrome will be all ZERO when there is no error */ for (i = 0; i < 6; i++) { @@ -930,7 +927,7 @@ static int doc_read_oob(struct mtd_info *mtd, loff_t ofs, uint8_t *buf = ops->oobbuf; size_t len = ops->len; - BUG_ON(ops->mode != MTD_OOB_PLACE); + BUG_ON(ops->mode != MTD_OPS_PLACE_OOB); ofs += ops->ooboffs; @@ -1094,7 +1091,7 @@ static int doc_write_oob(struct mtd_info *mtd, loff_t ofs, struct DiskOnChip *this = mtd->priv; int ret; - BUG_ON(ops->mode != MTD_OOB_PLACE); + BUG_ON(ops->mode != MTD_OPS_PLACE_OOB); mutex_lock(&this->lock); ret = doc_write_oob_nolock(mtd, ofs + ops->ooboffs, ops->len, diff --git a/drivers/mtd/devices/doc2001.c b/drivers/mtd/devices/doc2001.c index 241192f05bc..a3f7a27499b 100644 --- a/drivers/mtd/devices/doc2001.c +++ b/drivers/mtd/devices/doc2001.c @@ -55,15 +55,14 @@ static int _DoC_WaitReady(void __iomem * docptr) { unsigned short c = 0xffff; - DEBUG(MTD_DEBUG_LEVEL3, - "_DoC_WaitReady called for out-of-line wait\n"); + pr_debug("_DoC_WaitReady called for out-of-line wait\n"); /* Out-of-line routine to wait for chip response */ while (!(ReadDOC(docptr, CDSNControl) & CDSN_CTRL_FR_B) && --c) ; if (c == 0) - DEBUG(MTD_DEBUG_LEVEL2, "_DoC_WaitReady timed out.\n"); + pr_debug("_DoC_WaitReady timed out.\n"); return (c == 0); } @@ -464,7 +463,7 @@ static int doc_read (struct mtd_info *mtd, loff_t from, size_t len, #ifdef ECC_DEBUG printk("DiskOnChip ECC Error: Read at %lx\n", (long)from); #endif - /* Read the ECC syndrom through the DiskOnChip ECC logic. + /* Read the ECC syndrome through the DiskOnChip ECC logic. These syndrome will be all ZERO when there is no error */ for (i = 0; i < 6; i++) { syndrome[i] = ReadDOC(docptr, ECCSyndrome0 + i); @@ -632,7 +631,7 @@ static int doc_read_oob(struct mtd_info *mtd, loff_t ofs, uint8_t *buf = ops->oobbuf; size_t len = ops->len; - BUG_ON(ops->mode != MTD_OOB_PLACE); + BUG_ON(ops->mode != MTD_OPS_PLACE_OOB); ofs += ops->ooboffs; @@ -690,7 +689,7 @@ static int doc_write_oob(struct mtd_info *mtd, loff_t ofs, uint8_t *buf = ops->oobbuf; size_t len = ops->len; - BUG_ON(ops->mode != MTD_OOB_PLACE); + BUG_ON(ops->mode != MTD_OPS_PLACE_OOB); ofs += ops->ooboffs; diff --git a/drivers/mtd/devices/doc2001plus.c b/drivers/mtd/devices/doc2001plus.c index 09ae0adc3ad..99351bc3e0e 100644 --- a/drivers/mtd/devices/doc2001plus.c +++ b/drivers/mtd/devices/doc2001plus.c @@ -61,15 +61,14 @@ static int _DoC_WaitReady(void __iomem * docptr) { unsigned int c = 0xffff; - DEBUG(MTD_DEBUG_LEVEL3, - "_DoC_WaitReady called for out-of-line wait\n"); + pr_debug("_DoC_WaitReady called for out-of-line wait\n"); /* Out-of-line routine to wait for chip response */ while (((ReadDOC(docptr, Mplus_FlashControl) & CDSN_CTRL_FR_B_MASK) != CDSN_CTRL_FR_B_MASK) && --c) ; if (c == 0) - DEBUG(MTD_DEBUG_LEVEL2, "_DoC_WaitReady timed out.\n"); + pr_debug("_DoC_WaitReady timed out.\n"); return (c == 0); } @@ -655,7 +654,7 @@ static int doc_read(struct mtd_info *mtd, loff_t from, size_t len, #ifdef ECC_DEBUG printk("DiskOnChip ECC Error: Read at %lx\n", (long)from); #endif - /* Read the ECC syndrom through the DiskOnChip ECC logic. + /* Read the ECC syndrome through the DiskOnChip ECC logic. These syndrome will be all ZERO when there is no error */ for (i = 0; i < 6; i++) syndrome[i] = ReadDOC(docptr, Mplus_ECCSyndrome0 + i); @@ -835,7 +834,7 @@ static int doc_read_oob(struct mtd_info *mtd, loff_t ofs, uint8_t *buf = ops->oobbuf; size_t len = ops->len; - BUG_ON(ops->mode != MTD_OOB_PLACE); + BUG_ON(ops->mode != MTD_OPS_PLACE_OOB); ofs += ops->ooboffs; @@ -920,7 +919,7 @@ static int doc_write_oob(struct mtd_info *mtd, loff_t ofs, uint8_t *buf = ops->oobbuf; size_t len = ops->len; - BUG_ON(ops->mode != MTD_OOB_PLACE); + BUG_ON(ops->mode != MTD_OPS_PLACE_OOB); ofs += ops->ooboffs; diff --git a/drivers/mtd/devices/docecc.c b/drivers/mtd/devices/docecc.c index 37ef29a73ee..4a1c39b6f37 100644 --- a/drivers/mtd/devices/docecc.c +++ b/drivers/mtd/devices/docecc.c @@ -2,7 +2,7 @@ * ECC algorithm for M-systems disk on chip. We use the excellent Reed * Solmon code of Phil Karn (karn@ka9q.ampr.org) available under the * GNU GPL License. The rest is simply to convert the disk on chip - * syndrom into a standard syndom. + * syndrome into a standard syndome. * * Author: Fabrice Bellard (fabrice.bellard@netgem.com) * Copyright (C) 2000 Netgem S.A. diff --git a/drivers/mtd/devices/docg3.c b/drivers/mtd/devices/docg3.c new file mode 100644 index 00000000000..bdcf5df982e --- /dev/null +++ b/drivers/mtd/devices/docg3.c @@ -0,0 +1,1114 @@ +/* + * Handles the M-Systems DiskOnChip G3 chip + * + * Copyright (C) 2011 Robert Jarzmik + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/errno.h> +#include <linux/platform_device.h> +#include <linux/string.h> +#include <linux/slab.h> +#include <linux/io.h> +#include <linux/delay.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/partitions.h> + +#include <linux/debugfs.h> +#include <linux/seq_file.h> + +#define CREATE_TRACE_POINTS +#include "docg3.h" + +/* + * This driver handles the DiskOnChip G3 flash memory. + * + * As no specification is available from M-Systems/Sandisk, this drivers lacks + * several functions available on the chip, as : + * - block erase + * - page write + * - IPL write + * - ECC fixing (lack of BCH algorith understanding) + * - powerdown / powerup + * + * The bus data width (8bits versus 16bits) is not handled (if_cfg flag), and + * the driver assumes a 16bits data bus. + * + * DocG3 relies on 2 ECC algorithms, which are handled in hardware : + * - a 1 byte Hamming code stored in the OOB for each page + * - a 7 bytes BCH code stored in the OOB for each page + * The BCH part is only used for check purpose, no correction is available as + * some information is missing. What is known is that : + * - BCH is in GF(2^14) + * - BCH is over data of 520 bytes (512 page + 7 page_info bytes + * + 1 hamming byte) + * - BCH can correct up to 4 bits (t = 4) + * - BCH syndroms are calculated in hardware, and checked in hardware as well + * + */ + +static inline u8 doc_readb(struct docg3 *docg3, u16 reg) +{ + u8 val = readb(docg3->base + reg); + + trace_docg3_io(0, 8, reg, (int)val); + return val; +} + +static inline u16 doc_readw(struct docg3 *docg3, u16 reg) +{ + u16 val = readw(docg3->base + reg); + + trace_docg3_io(0, 16, reg, (int)val); + return val; +} + +static inline void doc_writeb(struct docg3 *docg3, u8 val, u16 reg) +{ + writeb(val, docg3->base + reg); + trace_docg3_io(1, 16, reg, val); +} + +static inline void doc_writew(struct docg3 *docg3, u16 val, u16 reg) +{ + writew(val, docg3->base + reg); + trace_docg3_io(1, 16, reg, val); +} + +static inline void doc_flash_command(struct docg3 *docg3, u8 cmd) +{ + doc_writeb(docg3, cmd, DOC_FLASHCOMMAND); +} + +static inline void doc_flash_sequence(struct docg3 *docg3, u8 seq) +{ + doc_writeb(docg3, seq, DOC_FLASHSEQUENCE); +} + +static inline void doc_flash_address(struct docg3 *docg3, u8 addr) +{ + doc_writeb(docg3, addr, DOC_FLASHADDRESS); +} + +static char const *part_probes[] = { "cmdlinepart", "saftlpart", NULL }; + +static int doc_register_readb(struct docg3 *docg3, int reg) +{ + u8 val; + + doc_writew(docg3, reg, DOC_READADDRESS); + val = doc_readb(docg3, reg); + doc_vdbg("Read register %04x : %02x\n", reg, val); + return val; +} + +static int doc_register_readw(struct docg3 *docg3, int reg) +{ + u16 val; + + doc_writew(docg3, reg, DOC_READADDRESS); + val = doc_readw(docg3, reg); + doc_vdbg("Read register %04x : %04x\n", reg, val); + return val; +} + +/** + * doc_delay - delay docg3 operations + * @docg3: the device + * @nbNOPs: the number of NOPs to issue + * + * As no specification is available, the right timings between chip commands are + * unknown. The only available piece of information are the observed nops on a + * working docg3 chip. + * Therefore, doc_delay relies on a busy loop of NOPs, instead of scheduler + * friendlier msleep() functions or blocking mdelay(). + */ +static void doc_delay(struct docg3 *docg3, int nbNOPs) +{ + int i; + + doc_dbg("NOP x %d\n", nbNOPs); + for (i = 0; i < nbNOPs; i++) + doc_writeb(docg3, 0, DOC_NOP); +} + +static int is_prot_seq_error(struct docg3 *docg3) +{ + int ctrl; + + ctrl = doc_register_readb(docg3, DOC_FLASHCONTROL); + return ctrl & (DOC_CTRL_PROTECTION_ERROR | DOC_CTRL_SEQUENCE_ERROR); +} + +static int doc_is_ready(struct docg3 *docg3) +{ + int ctrl; + + ctrl = doc_register_readb(docg3, DOC_FLASHCONTROL); + return ctrl & DOC_CTRL_FLASHREADY; +} + +static int doc_wait_ready(struct docg3 *docg3) +{ + int maxWaitCycles = 100; + + do { + doc_delay(docg3, 4); + cpu_relax(); + } while (!doc_is_ready(docg3) && maxWaitCycles--); + doc_delay(docg3, 2); + if (maxWaitCycles > 0) + return 0; + else + return -EIO; +} + +static int doc_reset_seq(struct docg3 *docg3) +{ + int ret; + + doc_writeb(docg3, 0x10, DOC_FLASHCONTROL); + doc_flash_sequence(docg3, DOC_SEQ_RESET); + doc_flash_command(docg3, DOC_CMD_RESET); + doc_delay(docg3, 2); + ret = doc_wait_ready(docg3); + + doc_dbg("doc_reset_seq() -> isReady=%s\n", ret ? "false" : "true"); + return ret; +} + +/** + * doc_read_data_area - Read data from data area + * @docg3: the device + * @buf: the buffer to fill in + * @len: the lenght to read + * @first: first time read, DOC_READADDRESS should be set + * + * Reads bytes from flash data. Handles the single byte / even bytes reads. + */ +static void doc_read_data_area(struct docg3 *docg3, void *buf, int len, + int first) +{ + int i, cdr, len4; + u16 data16, *dst16; + u8 data8, *dst8; + + doc_dbg("doc_read_data_area(buf=%p, len=%d)\n", buf, len); + cdr = len & 0x3; + len4 = len - cdr; + + if (first) + doc_writew(docg3, DOC_IOSPACE_DATA, DOC_READADDRESS); + dst16 = buf; + for (i = 0; i < len4; i += 2) { + data16 = doc_readw(docg3, DOC_IOSPACE_DATA); + *dst16 = data16; + dst16++; + } + + if (cdr) { + doc_writew(docg3, DOC_IOSPACE_DATA | DOC_READADDR_ONE_BYTE, + DOC_READADDRESS); + doc_delay(docg3, 1); + dst8 = (u8 *)dst16; + for (i = 0; i < cdr; i++) { + data8 = doc_readb(docg3, DOC_IOSPACE_DATA); + *dst8 = data8; + dst8++; + } + } +} + +/** + * doc_set_data_mode - Sets the flash to reliable data mode + * @docg3: the device + * + * The reliable data mode is a bit slower than the fast mode, but less errors + * occur. Entering the reliable mode cannot be done without entering the fast + * mode first. + */ +static void doc_set_reliable_mode(struct docg3 *docg3) +{ + doc_dbg("doc_set_reliable_mode()\n"); + doc_flash_sequence(docg3, DOC_SEQ_SET_MODE); + doc_flash_command(docg3, DOC_CMD_FAST_MODE); + doc_flash_command(docg3, DOC_CMD_RELIABLE_MODE); + doc_delay(docg3, 2); +} + +/** + * doc_set_asic_mode - Set the ASIC mode + * @docg3: the device + * @mode: the mode + * + * The ASIC can work in 3 modes : + * - RESET: all registers are zeroed + * - NORMAL: receives and handles commands + * - POWERDOWN: minimal poweruse, flash parts shut off + */ +static void doc_set_asic_mode(struct docg3 *docg3, u8 mode) +{ + int i; + + for (i = 0; i < 12; i++) + doc_readb(docg3, DOC_IOSPACE_IPL); + + mode |= DOC_ASICMODE_MDWREN; + doc_dbg("doc_set_asic_mode(%02x)\n", mode); + doc_writeb(docg3, mode, DOC_ASICMODE); + doc_writeb(docg3, ~mode, DOC_ASICMODECONFIRM); + doc_delay(docg3, 1); +} + +/** + * doc_set_device_id - Sets the devices id for cascaded G3 chips + * @docg3: the device + * @id: the chip to select (amongst 0, 1, 2, 3) + * + * There can be 4 cascaded G3 chips. This function selects the one which will + * should be the active one. + */ +static void doc_set_device_id(struct docg3 *docg3, int id) +{ + u8 ctrl; + + doc_dbg("doc_set_device_id(%d)\n", id); + doc_writeb(docg3, id, DOC_DEVICESELECT); + ctrl = doc_register_readb(docg3, DOC_FLASHCONTROL); + + ctrl &= ~DOC_CTRL_VIOLATION; + ctrl |= DOC_CTRL_CE; + doc_writeb(docg3, ctrl, DOC_FLASHCONTROL); +} + +/** + * doc_set_extra_page_mode - Change flash page layout + * @docg3: the device + * + * Normally, the flash page is split into the data (512 bytes) and the out of + * band data (16 bytes). For each, 4 more bytes can be accessed, where the wear + * leveling counters are stored. To access this last area of 4 bytes, a special + * mode must be input to the flash ASIC. + * + * Returns 0 if no error occured, -EIO else. + */ +static int doc_set_extra_page_mode(struct docg3 *docg3) +{ + int fctrl; + + doc_dbg("doc_set_extra_page_mode()\n"); + doc_flash_sequence(docg3, DOC_SEQ_PAGE_SIZE_532); + doc_flash_command(docg3, DOC_CMD_PAGE_SIZE_532); + doc_delay(docg3, 2); + + fctrl = doc_register_readb(docg3, DOC_FLASHCONTROL); + if (fctrl & (DOC_CTRL_PROTECTION_ERROR | DOC_CTRL_SEQUENCE_ERROR)) + return -EIO; + else + return 0; +} + +/** + * doc_seek - Set both flash planes to the specified block, page for reading + * @docg3: the device + * @block0: the first plane block index + * @block1: the second plane block index + * @page: the page index within the block + * @wear: if true, read will occur on the 4 extra bytes of the wear area + * @ofs: offset in page to read + * + * Programs the flash even and odd planes to the specific block and page. + * Alternatively, programs the flash to the wear area of the specified page. + */ +static int doc_read_seek(struct docg3 *docg3, int block0, int block1, int page, + int wear, int ofs) +{ + int sector, ret = 0; + + doc_dbg("doc_seek(blocks=(%d,%d), page=%d, ofs=%d, wear=%d)\n", + block0, block1, page, ofs, wear); + + if (!wear && (ofs < 2 * DOC_LAYOUT_PAGE_SIZE)) { + doc_flash_sequence(docg3, DOC_SEQ_SET_PLANE1); + doc_flash_command(docg3, DOC_CMD_READ_PLANE1); + doc_delay(docg3, 2); + } else { + doc_flash_sequence(docg3, DOC_SEQ_SET_PLANE2); + doc_flash_command(docg3, DOC_CMD_READ_PLANE2); + doc_delay(docg3, 2); + } + + doc_set_reliable_mode(docg3); + if (wear) + ret = doc_set_extra_page_mode(docg3); + if (ret) + goto out; + + sector = (block0 << DOC_ADDR_BLOCK_SHIFT) + (page & DOC_ADDR_PAGE_MASK); + doc_flash_sequence(docg3, DOC_SEQ_READ); + doc_flash_command(docg3, DOC_CMD_PROG_BLOCK_ADDR); + doc_delay(docg3, 1); + doc_flash_address(docg3, sector & 0xff); + doc_flash_address(docg3, (sector >> 8) & 0xff); + doc_flash_address(docg3, (sector >> 16) & 0xff); + doc_delay(docg3, 1); + + sector = (block1 << DOC_ADDR_BLOCK_SHIFT) + (page & DOC_ADDR_PAGE_MASK); + doc_flash_command(docg3, DOC_CMD_PROG_BLOCK_ADDR); + doc_delay(docg3, 1); + doc_flash_address(docg3, sector & 0xff); + doc_flash_address(docg3, (sector >> 8) & 0xff); + doc_flash_address(docg3, (sector >> 16) & 0xff); + doc_delay(docg3, 2); + +out: + return ret; +} + +/** + * doc_read_page_ecc_init - Initialize hardware ECC engine + * @docg3: the device + * @len: the number of bytes covered by the ECC (BCH covered) + * + * The function does initialize the hardware ECC engine to compute the Hamming + * ECC (on 1 byte) and the BCH Syndroms (on 7 bytes). + * + * Return 0 if succeeded, -EIO on error + */ +static int doc_read_page_ecc_init(struct docg3 *docg3, int len) +{ + doc_writew(docg3, DOC_ECCCONF0_READ_MODE + | DOC_ECCCONF0_BCH_ENABLE | DOC_ECCCONF0_HAMMING_ENABLE + | (len & DOC_ECCCONF0_DATA_BYTES_MASK), + DOC_ECCCONF0); + doc_delay(docg3, 4); + doc_register_readb(docg3, DOC_FLASHCONTROL); + return doc_wait_ready(docg3); +} + +/** + * doc_read_page_prepare - Prepares reading data from a flash page + * @docg3: the device + * @block0: the first plane block index on flash memory + * @block1: the second plane block index on flash memory + * @page: the page index in the block + * @offset: the offset in the page (must be a multiple of 4) + * + * Prepares the page to be read in the flash memory : + * - tell ASIC to map the flash pages + * - tell ASIC to be in read mode + * + * After a call to this method, a call to doc_read_page_finish is mandatory, + * to end the read cycle of the flash. + * + * Read data from a flash page. The length to be read must be between 0 and + * (page_size + oob_size + wear_size), ie. 532, and a multiple of 4 (because + * the extra bytes reading is not implemented). + * + * As pages are grouped by 2 (in 2 planes), reading from a page must be done + * in two steps: + * - one read of 512 bytes at offset 0 + * - one read of 512 bytes at offset 512 + 16 + * + * Returns 0 if successful, -EIO if a read error occured. + */ +static int doc_read_page_prepare(struct docg3 *docg3, int block0, int block1, + int page, int offset) +{ + int wear_area = 0, ret = 0; + + doc_dbg("doc_read_page_prepare(blocks=(%d,%d), page=%d, ofsInPage=%d)\n", + block0, block1, page, offset); + if (offset >= DOC_LAYOUT_WEAR_OFFSET) + wear_area = 1; + if (!wear_area && offset > (DOC_LAYOUT_PAGE_OOB_SIZE * 2)) + return -EINVAL; + + doc_set_device_id(docg3, docg3->device_id); + ret = doc_reset_seq(docg3); + if (ret) + goto err; + + /* Program the flash address block and page */ + ret = doc_read_seek(docg3, block0, block1, page, wear_area, offset); + if (ret) + goto err; + + doc_flash_command(docg3, DOC_CMD_READ_ALL_PLANES); + doc_delay(docg3, 2); + doc_wait_ready(docg3); + + doc_flash_command(docg3, DOC_CMD_SET_ADDR_READ); + doc_delay(docg3, 1); + if (offset >= DOC_LAYOUT_PAGE_SIZE * 2) + offset -= 2 * DOC_LAYOUT_PAGE_SIZE; + doc_flash_address(docg3, offset >> 2); + doc_delay(docg3, 1); + doc_wait_ready(docg3); + + doc_flash_command(docg3, DOC_CMD_READ_FLASH); + + return 0; +err: + doc_writeb(docg3, 0, DOC_DATAEND); + doc_delay(docg3, 2); + return -EIO; +} + +/** + * doc_read_page_getbytes - Reads bytes from a prepared page + * @docg3: the device + * @len: the number of bytes to be read (must be a multiple of 4) + * @buf: the buffer to be filled in + * @first: 1 if first time read, DOC_READADDRESS should be set + * + */ +static int doc_read_page_getbytes(struct docg3 *docg3, int len, u_char *buf, + int first) +{ + doc_read_data_area(docg3, buf, len, first); + doc_delay(docg3, 2); + return len; +} + +/** + * doc_get_hw_bch_syndroms - Get hardware calculated BCH syndroms + * @docg3: the device + * @syns: the array of 7 integers where the syndroms will be stored + */ +static void doc_get_hw_bch_syndroms(struct docg3 *docg3, int *syns) +{ + int i; + + for (i = 0; i < DOC_ECC_BCH_SIZE; i++) + syns[i] = doc_register_readb(docg3, DOC_BCH_SYNDROM(i)); +} + +/** + * doc_read_page_finish - Ends reading of a flash page + * @docg3: the device + * + * As a side effect, resets the chip selector to 0. This ensures that after each + * read operation, the floor 0 is selected. Therefore, if the systems halts, the + * reboot will boot on floor 0, where the IPL is. + */ +static void doc_read_page_finish(struct docg3 *docg3) +{ + doc_writeb(docg3, 0, DOC_DATAEND); + doc_delay(docg3, 2); + doc_set_device_id(docg3, 0); +} + +/** + * calc_block_sector - Calculate blocks, pages and ofs. + + * @from: offset in flash + * @block0: first plane block index calculated + * @block1: second plane block index calculated + * @page: page calculated + * @ofs: offset in page + */ +static void calc_block_sector(loff_t from, int *block0, int *block1, int *page, + int *ofs) +{ + uint sector; + + sector = from / DOC_LAYOUT_PAGE_SIZE; + *block0 = sector / (DOC_LAYOUT_PAGES_PER_BLOCK * DOC_LAYOUT_NBPLANES) + * DOC_LAYOUT_NBPLANES; + *block1 = *block0 + 1; + *page = sector % (DOC_LAYOUT_PAGES_PER_BLOCK * DOC_LAYOUT_NBPLANES); + *page /= DOC_LAYOUT_NBPLANES; + if (sector % 2) + *ofs = DOC_LAYOUT_PAGE_OOB_SIZE; + else + *ofs = 0; +} + +/** + * doc_read - Read bytes from flash + * @mtd: the device + * @from: the offset from first block and first page, in bytes, aligned on page + * size + * @len: the number of bytes to read (must be a multiple of 4) + * @retlen: the number of bytes actually read + * @buf: the filled in buffer + * + * Reads flash memory pages. This function does not read the OOB chunk, but only + * the page data. + * + * Returns 0 if read successfull, of -EIO, -EINVAL if an error occured + */ +static int doc_read(struct mtd_info *mtd, loff_t from, size_t len, + size_t *retlen, u_char *buf) +{ + struct docg3 *docg3 = mtd->priv; + int block0, block1, page, readlen, ret, ofs = 0; + int syn[DOC_ECC_BCH_SIZE], eccconf1; + u8 oob[DOC_LAYOUT_OOB_SIZE]; + + ret = -EINVAL; + doc_dbg("doc_read(from=%lld, len=%zu, buf=%p)\n", from, len, buf); + if (from % DOC_LAYOUT_PAGE_SIZE) + goto err; + if (len % 4) + goto err; + calc_block_sector(from, &block0, &block1, &page, &ofs); + if (block1 > docg3->max_block) + goto err; + + *retlen = 0; + ret = 0; + readlen = min_t(size_t, len, (size_t)DOC_LAYOUT_PAGE_SIZE); + while (!ret && len > 0) { + readlen = min_t(size_t, len, (size_t)DOC_LAYOUT_PAGE_SIZE); + ret = doc_read_page_prepare(docg3, block0, block1, page, ofs); + if (ret < 0) + goto err; + ret = doc_read_page_ecc_init(docg3, DOC_ECC_BCH_COVERED_BYTES); + if (ret < 0) + goto err_in_read; + ret = doc_read_page_getbytes(docg3, readlen, buf, 1); + if (ret < readlen) + goto err_in_read; + ret = doc_read_page_getbytes(docg3, DOC_LAYOUT_OOB_SIZE, + oob, 0); + if (ret < DOC_LAYOUT_OOB_SIZE) + goto err_in_read; + + *retlen += readlen; + buf += readlen; + len -= readlen; + + ofs ^= DOC_LAYOUT_PAGE_OOB_SIZE; + if (ofs == 0) + page += 2; + if (page > DOC_ADDR_PAGE_MASK) { + page = 0; + block0 += 2; + block1 += 2; + } + + /* + * There should be a BCH bitstream fixing algorithm here ... + * By now, a page read failure is triggered by BCH error + */ + doc_get_hw_bch_syndroms(docg3, syn); + eccconf1 = doc_register_readb(docg3, DOC_ECCCONF1); + + doc_dbg("OOB - INFO: %02x:%02x:%02x:%02x:%02x:%02x:%02x\n", + oob[0], oob[1], oob[2], oob[3], oob[4], + oob[5], oob[6]); + doc_dbg("OOB - HAMMING: %02x\n", oob[7]); + doc_dbg("OOB - BCH_ECC: %02x:%02x:%02x:%02x:%02x:%02x:%02x\n", + oob[8], oob[9], oob[10], oob[11], oob[12], + oob[13], oob[14]); + doc_dbg("OOB - UNUSED: %02x\n", oob[15]); + doc_dbg("ECC checks: ECCConf1=%x\n", eccconf1); + doc_dbg("ECC BCH syndrom: %02x:%02x:%02x:%02x:%02x:%02x:%02x\n", + syn[0], syn[1], syn[2], syn[3], syn[4], syn[5], syn[6]); + + ret = -EBADMSG; + if (block0 >= DOC_LAYOUT_BLOCK_FIRST_DATA) { + if (eccconf1 & DOC_ECCCONF1_BCH_SYNDROM_ERR) + goto err_in_read; + if (is_prot_seq_error(docg3)) + goto err_in_read; + } + doc_read_page_finish(docg3); + } + + return 0; +err_in_read: + doc_read_page_finish(docg3); +err: + return ret; +} + +/** + * doc_read_oob - Read out of band bytes from flash + * @mtd: the device + * @from: the offset from first block and first page, in bytes, aligned on page + * size + * @ops: the mtd oob structure + * + * Reads flash memory OOB area of pages. + * + * Returns 0 if read successfull, of -EIO, -EINVAL if an error occured + */ +static int doc_read_oob(struct mtd_info *mtd, loff_t from, + struct mtd_oob_ops *ops) +{ + struct docg3 *docg3 = mtd->priv; + int block0, block1, page, ofs, ret; + u8 *buf = ops->oobbuf; + size_t len = ops->ooblen; + + doc_dbg("doc_read_oob(from=%lld, buf=%p, len=%zu)\n", from, buf, len); + if (len != DOC_LAYOUT_OOB_SIZE) + return -EINVAL; + + switch (ops->mode) { + case MTD_OPS_PLACE_OOB: + buf += ops->ooboffs; + break; + default: + break; + } + + calc_block_sector(from, &block0, &block1, &page, &ofs); + if (block1 > docg3->max_block) + return -EINVAL; + + ret = doc_read_page_prepare(docg3, block0, block1, page, + ofs + DOC_LAYOUT_PAGE_SIZE); + if (!ret) + ret = doc_read_page_ecc_init(docg3, DOC_LAYOUT_OOB_SIZE); + if (!ret) + ret = doc_read_page_getbytes(docg3, DOC_LAYOUT_OOB_SIZE, + buf, 1); + doc_read_page_finish(docg3); + + if (ret > 0) + ops->oobretlen = ret; + else + ops->oobretlen = 0; + return (ret > 0) ? 0 : ret; +} + +static int doc_reload_bbt(struct docg3 *docg3) +{ + int block = DOC_LAYOUT_BLOCK_BBT; + int ret = 0, nbpages, page; + u_char *buf = docg3->bbt; + + nbpages = DIV_ROUND_UP(docg3->max_block + 1, 8 * DOC_LAYOUT_PAGE_SIZE); + for (page = 0; !ret && (page < nbpages); page++) { + ret = doc_read_page_prepare(docg3, block, block + 1, + page + DOC_LAYOUT_PAGE_BBT, 0); + if (!ret) + ret = doc_read_page_ecc_init(docg3, + DOC_LAYOUT_PAGE_SIZE); + if (!ret) + doc_read_page_getbytes(docg3, DOC_LAYOUT_PAGE_SIZE, + buf, 1); + buf += DOC_LAYOUT_PAGE_SIZE; + } + doc_read_page_finish(docg3); + return ret; +} + +/** + * doc_block_isbad - Checks whether a block is good or not + * @mtd: the device + * @from: the offset to find the correct block + * + * Returns 1 if block is bad, 0 if block is good + */ +static int doc_block_isbad(struct mtd_info *mtd, loff_t from) +{ + struct docg3 *docg3 = mtd->priv; + int block0, block1, page, ofs, is_good; + + calc_block_sector(from, &block0, &block1, &page, &ofs); + doc_dbg("doc_block_isbad(from=%lld) => block=(%d,%d), page=%d, ofs=%d\n", + from, block0, block1, page, ofs); + + if (block0 < DOC_LAYOUT_BLOCK_FIRST_DATA) + return 0; + if (block1 > docg3->max_block) + return -EINVAL; + + is_good = docg3->bbt[block0 >> 3] & (1 << (block0 & 0x7)); + return !is_good; +} + +/** + * doc_get_erase_count - Get block erase count + * @docg3: the device + * @from: the offset in which the block is. + * + * Get the number of times a block was erased. The number is the maximum of + * erase times between first and second plane (which should be equal normally). + * + * Returns The number of erases, or -EINVAL or -EIO on error. + */ +static int doc_get_erase_count(struct docg3 *docg3, loff_t from) +{ + u8 buf[DOC_LAYOUT_WEAR_SIZE]; + int ret, plane1_erase_count, plane2_erase_count; + int block0, block1, page, ofs; + + doc_dbg("doc_get_erase_count(from=%lld, buf=%p)\n", from, buf); + if (from % DOC_LAYOUT_PAGE_SIZE) + return -EINVAL; + calc_block_sector(from, &block0, &block1, &page, &ofs); + if (block1 > docg3->max_block) + return -EINVAL; + + ret = doc_reset_seq(docg3); + if (!ret) + ret = doc_read_page_prepare(docg3, block0, block1, page, + ofs + DOC_LAYOUT_WEAR_OFFSET); + if (!ret) + ret = doc_read_page_getbytes(docg3, DOC_LAYOUT_WEAR_SIZE, + buf, 1); + doc_read_page_finish(docg3); + + if (ret || (buf[0] != DOC_ERASE_MARK) || (buf[2] != DOC_ERASE_MARK)) + return -EIO; + plane1_erase_count = (u8)(~buf[1]) | ((u8)(~buf[4]) << 8) + | ((u8)(~buf[5]) << 16); + plane2_erase_count = (u8)(~buf[3]) | ((u8)(~buf[6]) << 8) + | ((u8)(~buf[7]) << 16); + + return max |