diff options
Diffstat (limited to 'drivers/mmc/core/core.c')
-rw-r--r-- | drivers/mmc/core/core.c | 98 |
1 files changed, 64 insertions, 34 deletions
diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c index 5278ffb20e7..950b97d7412 100644 --- a/drivers/mmc/core/core.c +++ b/drivers/mmc/core/core.c @@ -529,6 +529,18 @@ void mmc_set_data_timeout(struct mmc_data *data, const struct mmc_card *card) data->timeout_clks = 0; } } + + /* + * Some cards require longer data read timeout than indicated in CSD. + * Address this by setting the read timeout to a "reasonably high" + * value. For the cards tested, 300ms has proven enough. If necessary, + * this value can be increased if other problematic cards require this. + */ + if (mmc_card_long_read_time(card) && data->flags & MMC_DATA_READ) { + data->timeout_ns = 300000000; + data->timeout_clks = 0; + } + /* * Some cards need very high timeouts if driven in SPI mode. * The worst observed timeout was 900ms after writing a @@ -1213,6 +1225,46 @@ void mmc_set_driver_type(struct mmc_host *host, unsigned int drv_type) mmc_host_clk_release(host); } +static void mmc_poweroff_notify(struct mmc_host *host) +{ + struct mmc_card *card; + unsigned int timeout; + unsigned int notify_type = EXT_CSD_NO_POWER_NOTIFICATION; + int err = 0; + + card = host->card; + + /* + * Send power notify command only if card + * is mmc and notify state is powered ON + */ + if (card && mmc_card_mmc(card) && + (card->poweroff_notify_state == MMC_POWERED_ON)) { + + if (host->power_notify_type == MMC_HOST_PW_NOTIFY_SHORT) { + notify_type = EXT_CSD_POWER_OFF_SHORT; + timeout = card->ext_csd.generic_cmd6_time; + card->poweroff_notify_state = MMC_POWEROFF_SHORT; + } else { + notify_type = EXT_CSD_POWER_OFF_LONG; + timeout = card->ext_csd.power_off_longtime; + card->poweroff_notify_state = MMC_POWEROFF_LONG; + } + + err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL, + EXT_CSD_POWER_OFF_NOTIFICATION, + notify_type, timeout); + + if (err && err != -EBADMSG) + pr_err("Device failed to respond within %d poweroff " + "time. Forcefully powering down the device\n", + timeout); + + /* Set the card state to no notification after the poweroff */ + card->poweroff_notify_state = MMC_NO_POWER_NOTIFICATION; + } +} + /* * Apply power to the MMC stack. This is a two-stage process. * First, we enable power to the card without the clock running. @@ -1269,42 +1321,12 @@ static void mmc_power_up(struct mmc_host *host) void mmc_power_off(struct mmc_host *host) { - struct mmc_card *card; - unsigned int notify_type; - unsigned int timeout; - int err; - mmc_host_clk_hold(host); - card = host->card; host->ios.clock = 0; host->ios.vdd = 0; - if (card && mmc_card_mmc(card) && - (card->poweroff_notify_state == MMC_POWERED_ON)) { - - if (host->power_notify_type == MMC_HOST_PW_NOTIFY_SHORT) { - notify_type = EXT_CSD_POWER_OFF_SHORT; - timeout = card->ext_csd.generic_cmd6_time; - card->poweroff_notify_state = MMC_POWEROFF_SHORT; - } else { - notify_type = EXT_CSD_POWER_OFF_LONG; - timeout = card->ext_csd.power_off_longtime; - card->poweroff_notify_state = MMC_POWEROFF_LONG; - } - - err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL, - EXT_CSD_POWER_OFF_NOTIFICATION, - notify_type, timeout); - - if (err && err != -EBADMSG) - pr_err("Device failed to respond within %d poweroff " - "time. Forcefully powering down the device\n", - timeout); - - /* Set the card state to no notification after the poweroff */ - card->poweroff_notify_state = MMC_NO_POWER_NOTIFICATION; - } + mmc_poweroff_notify(host); /* * Reset ocr mask to be the highest possible voltage supported for @@ -2196,7 +2218,7 @@ int mmc_card_sleep(struct mmc_host *host) mmc_bus_get(host); - if (host->bus_ops && !host->bus_dead && host->bus_ops->awake) + if (host->bus_ops && !host->bus_dead && host->bus_ops->sleep) err = host->bus_ops->sleep(host); mmc_bus_put(host); @@ -2302,8 +2324,17 @@ int mmc_suspend_host(struct mmc_host *host) * pre-claim the host. */ if (mmc_try_claim_host(host)) { - if (host->bus_ops->suspend) + if (host->bus_ops->suspend) { + /* + * For eMMC 4.5 device send notify command + * before sleep, because in sleep state eMMC 4.5 + * devices respond to only RESET and AWAKE cmd + */ + mmc_poweroff_notify(host); err = host->bus_ops->suspend(host); + } + mmc_do_release_host(host); + if (err == -ENOSYS || !host->bus_ops->resume) { /* * We simply "remove" the card in this case. @@ -2318,7 +2349,6 @@ int mmc_suspend_host(struct mmc_host *host) host->pm_flags = 0; err = 0; } - mmc_do_release_host(host); } else { err = -EBUSY; } |