diff options
Diffstat (limited to 'drivers/media')
-rw-r--r-- | drivers/media/dvb/bt8xx/bt878.c | 2 | ||||
-rw-r--r-- | drivers/media/dvb/ttusb-budget/dvb-ttusb-budget.c | 2 | ||||
-rw-r--r-- | drivers/media/video/bt8xx/bttv-cards.c | 22 | ||||
-rw-r--r-- | drivers/media/video/em28xx/em28xx-video.c | 2 |
4 files changed, 14 insertions, 14 deletions
diff --git a/drivers/media/dvb/bt8xx/bt878.c b/drivers/media/dvb/bt8xx/bt878.c index eca602d9b3d..85e36a1d6d7 100644 --- a/drivers/media/dvb/bt8xx/bt878.c +++ b/drivers/media/dvb/bt8xx/bt878.c @@ -280,7 +280,7 @@ static irqreturn_t bt878_irq(int irq, void *dev_id) if (!(astat = (stat & mask))) return IRQ_NONE; /* this interrupt is not for me */ /* dprintk("bt878(%d) debug: irq count %d, stat 0x%8.8x, mask 0x%8.8x\n",bt->nr,count,stat,mask); */ - btwrite(astat, BT878_AINT_STAT); /* try to clear interupt condition */ + btwrite(astat, BT878_AINT_STAT); /* try to clear interrupt condition */ if (astat & (BT878_ASCERR | BT878_AOCERR)) { diff --git a/drivers/media/dvb/ttusb-budget/dvb-ttusb-budget.c b/drivers/media/dvb/ttusb-budget/dvb-ttusb-budget.c index 288e79f2cb0..7902ae1d9a1 100644 --- a/drivers/media/dvb/ttusb-budget/dvb-ttusb-budget.c +++ b/drivers/media/dvb/ttusb-budget/dvb-ttusb-budget.c @@ -128,7 +128,7 @@ struct ttusb { struct dvb_frontend* fe; }; -/* ugly workaround ... don't know why it's neccessary to read */ +/* ugly workaround ... don't know why it's necessary to read */ /* all result codes. */ #define DEBUG 0 diff --git a/drivers/media/video/bt8xx/bttv-cards.c b/drivers/media/video/bt8xx/bttv-cards.c index dd6a7d68b07..3162223a2ff 100644 --- a/drivers/media/video/bt8xx/bttv-cards.c +++ b/drivers/media/video/bt8xx/bttv-cards.c @@ -4709,18 +4709,18 @@ adtvk503_audio(struct bttv *btv, struct video_audio *v, int set) * * The board hardwire Y0 (xpoint) to MUX1 and MUXOUT to Yin. * GPIO pins are wired as: - * GPIO[0:3] - AX[0:3] (xpoint) - P1[0:3] (microcontroler) - * GPIO[4:6] - AY[0:2] (xpoint) - P1[4:6] (microcontroler) - * GPIO[7] - DATA (xpoint) - P1[7] (microcontroler) - * GPIO[8] - - P3[5] (microcontroler) - * GPIO[9] - RESET (xpoint) - P3[6] (microcontroler) - * GPIO[10] - STROBE (xpoint) - P3[7] (microcontroler) - * GPINTR - - P3[4] (microcontroler) + * GPIO[0:3] - AX[0:3] (xpoint) - P1[0:3] (microcontroller) + * GPIO[4:6] - AY[0:2] (xpoint) - P1[4:6] (microcontroller) + * GPIO[7] - DATA (xpoint) - P1[7] (microcontroller) + * GPIO[8] - - P3[5] (microcontroller) + * GPIO[9] - RESET (xpoint) - P3[6] (microcontroller) + * GPIO[10] - STROBE (xpoint) - P3[7] (microcontroller) + * GPINTR - - P3[4] (microcontroller) * - * The microcontroler is a 80C32 like. It should be possible to change xpoint - * configuration either directly (as we are doing) or using the microcontroler + * The microcontroller is a 80C32 like. It should be possible to change xpoint + * configuration either directly (as we are doing) or using the microcontroller * which is also wired to I2C interface. I have no further info on the - * microcontroler features, one would need to disassembly the firmware. + * microcontroller features, one would need to disassembly the firmware. * note: the vendor refused to give any information on this product, all * that stuff was found using a multimeter! :) */ @@ -4788,7 +4788,7 @@ static void tibetCS16_init(struct bttv *btv) * The analog switch is controlled by the "master", but the detection order * of the four BT878A chips is in an order which I just don't understand. * The "master" is actually the second controller to be detected. The - * logic on the board uses logical numbers for the 4 controlers, but + * logic on the board uses logical numbers for the 4 controllers, but * those numbers are different from the detection sequence. When working * with the analog switch, we need to "map" from the detection sequence * over to the board's logical controller number. This mapping sequence diff --git a/drivers/media/video/em28xx/em28xx-video.c b/drivers/media/video/em28xx/em28xx-video.c index b8d5327c438..e467682aabd 100644 --- a/drivers/media/video/em28xx/em28xx-video.c +++ b/drivers/media/video/em28xx/em28xx-video.c @@ -907,7 +907,7 @@ static int em28xx_set_fmt(struct em28xx *dev, unsigned int cmd, struct v4l2_form /* stop io in case it is already in progress */ if (dev->stream == STREAM_ON) { - em28xx_videodbg("VIDIOC_SET_FMT: interupting stream\n"); + em28xx_videodbg("VIDIOC_SET_FMT: interrupting stream\n"); if ((ret = em28xx_stream_interrupt(dev))) return ret; } |