diff options
Diffstat (limited to 'drivers/media/video/marvell-ccic/cafe-driver.c')
-rw-r--r-- | drivers/media/video/marvell-ccic/cafe-driver.c | 654 |
1 files changed, 654 insertions, 0 deletions
diff --git a/drivers/media/video/marvell-ccic/cafe-driver.c b/drivers/media/video/marvell-ccic/cafe-driver.c new file mode 100644 index 00000000000..d030f9beae8 --- /dev/null +++ b/drivers/media/video/marvell-ccic/cafe-driver.c @@ -0,0 +1,654 @@ +/* + * A driver for the CMOS camera controller in the Marvell 88ALP01 "cafe" + * multifunction chip. Currently works with the Omnivision OV7670 + * sensor. + * + * The data sheet for this device can be found at: + * http://www.marvell.com/products/pc_connectivity/88alp01/ + * + * Copyright 2006-11 One Laptop Per Child Association, Inc. + * Copyright 2006-11 Jonathan Corbet <corbet@lwn.net> + * + * Written by Jonathan Corbet, corbet@lwn.net. + * + * v4l2_device/v4l2_subdev conversion by: + * Copyright (C) 2009 Hans Verkuil <hverkuil@xs4all.nl> + * + * This file may be distributed under the terms of the GNU General + * Public License, version 2. + */ +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/init.h> +#include <linux/pci.h> +#include <linux/i2c.h> +#include <linux/interrupt.h> +#include <linux/spinlock.h> +#include <linux/slab.h> +#include <linux/videodev2.h> +#include <media/v4l2-device.h> +#include <media/v4l2-chip-ident.h> +#include <linux/device.h> +#include <linux/wait.h> +#include <linux/delay.h> +#include <linux/io.h> + +#include "mcam-core.h" + +#define CAFE_VERSION 0x000002 + + +/* + * Parameters. + */ +MODULE_AUTHOR("Jonathan Corbet <corbet@lwn.net>"); +MODULE_DESCRIPTION("Marvell 88ALP01 CMOS Camera Controller driver"); +MODULE_LICENSE("GPL"); +MODULE_SUPPORTED_DEVICE("Video"); + + + + +struct cafe_camera { + int registered; /* Fully initialized? */ + struct mcam_camera mcam; + struct pci_dev *pdev; + wait_queue_head_t smbus_wait; /* Waiting on i2c events */ +}; + +/* + * Most of the camera controller registers are defined in mcam-core.h, + * but the Cafe platform has some additional registers of its own; + * they are described here. + */ + +/* + * "General purpose register" has a couple of GPIOs used for sensor + * power and reset on OLPC XO 1.0 systems. + */ +#define REG_GPR 0xb4 +#define GPR_C1EN 0x00000020 /* Pad 1 (power down) enable */ +#define GPR_C0EN 0x00000010 /* Pad 0 (reset) enable */ +#define GPR_C1 0x00000002 /* Control 1 value */ +/* + * Control 0 is wired to reset on OLPC machines. For ov7x sensors, + * it is active low. + */ +#define GPR_C0 0x00000001 /* Control 0 value */ + +/* + * These registers control the SMBUS module for communicating + * with the sensor. + */ +#define REG_TWSIC0 0xb8 /* TWSI (smbus) control 0 */ +#define TWSIC0_EN 0x00000001 /* TWSI enable */ +#define TWSIC0_MODE 0x00000002 /* 1 = 16-bit, 0 = 8-bit */ +#define TWSIC0_SID 0x000003fc /* Slave ID */ +/* + * Subtle trickery: the slave ID field starts with bit 2. But the + * Linux i2c stack wants to treat the bottommost bit as a separate + * read/write bit, which is why slave ID's are usually presented + * >>1. For consistency with that behavior, we shift over three + * bits instead of two. + */ +#define TWSIC0_SID_SHIFT 3 +#define TWSIC0_CLKDIV 0x0007fc00 /* Clock divider */ +#define TWSIC0_MASKACK 0x00400000 /* Mask ack from sensor */ +#define TWSIC0_OVMAGIC 0x00800000 /* Make it work on OV sensors */ + +#define REG_TWSIC1 0xbc /* TWSI control 1 */ +#define TWSIC1_DATA 0x0000ffff /* Data to/from camchip */ +#define TWSIC1_ADDR 0x00ff0000 /* Address (register) */ +#define TWSIC1_ADDR_SHIFT 16 +#define TWSIC1_READ 0x01000000 /* Set for read op */ +#define TWSIC1_WSTAT 0x02000000 /* Write status */ +#define TWSIC1_RVALID 0x04000000 /* Read data valid */ +#define TWSIC1_ERROR 0x08000000 /* Something screwed up */ + +/* + * Here's the weird global control registers + */ +#define REG_GL_CSR 0x3004 /* Control/status register */ +#define GCSR_SRS 0x00000001 /* SW Reset set */ +#define GCSR_SRC 0x00000002 /* SW Reset clear */ +#define GCSR_MRS 0x00000004 /* Master reset set */ +#define GCSR_MRC 0x00000008 /* HW Reset clear */ +#define GCSR_CCIC_EN 0x00004000 /* CCIC Clock enable */ +#define REG_GL_IMASK 0x300c /* Interrupt mask register */ +#define GIMSK_CCIC_EN 0x00000004 /* CCIC Interrupt enable */ + +#define REG_GL_FCR 0x3038 /* GPIO functional control register */ +#define GFCR_GPIO_ON 0x08 /* Camera GPIO enabled */ +#define REG_GL_GPIOR 0x315c /* GPIO register */ +#define GGPIO_OUT 0x80000 /* GPIO output */ +#define GGPIO_VAL 0x00008 /* Output pin value */ + +#define REG_LEN (REG_GL_IMASK + 4) + + +/* + * Debugging and related. + */ +#define cam_err(cam, fmt, arg...) \ + dev_err(&(cam)->pdev->dev, fmt, ##arg); +#define cam_warn(cam, fmt, arg...) \ + dev_warn(&(cam)->pdev->dev, fmt, ##arg); + +/* -------------------------------------------------------------------- */ +/* + * The I2C/SMBUS interface to the camera itself starts here. The + * controller handles SMBUS itself, presenting a relatively simple register + * interface; all we have to do is to tell it where to route the data. + */ +#define CAFE_SMBUS_TIMEOUT (HZ) /* generous */ + +static inline struct cafe_camera *to_cam(struct v4l2_device *dev) +{ + struct mcam_camera *m = container_of(dev, struct mcam_camera, v4l2_dev); + return container_of(m, struct cafe_camera, mcam); +} + + +static int cafe_smbus_write_done(struct mcam_camera *mcam) +{ + unsigned long flags; + int c1; + + /* + * We must delay after the interrupt, or the controller gets confused + * and never does give us good status. Fortunately, we don't do this + * often. + */ + udelay(20); + spin_lock_irqsave(&mcam->dev_lock, flags); + c1 = mcam_reg_read(mcam, REG_TWSIC1); + spin_unlock_irqrestore(&mcam->dev_lock, flags); + return (c1 & (TWSIC1_WSTAT|TWSIC1_ERROR)) != TWSIC1_WSTAT; +} + +static int cafe_smbus_write_data(struct cafe_camera *cam, + u16 addr, u8 command, u8 value) +{ + unsigned int rval; + unsigned long flags; + struct mcam_camera *mcam = &cam->mcam; + + spin_lock_irqsave(&mcam->dev_lock, flags); + rval = TWSIC0_EN | ((addr << TWSIC0_SID_SHIFT) & TWSIC0_SID); + rval |= TWSIC0_OVMAGIC; /* Make OV sensors work */ + /* + * Marvell sez set clkdiv to all 1's for now. + */ + rval |= TWSIC0_CLKDIV; + mcam_reg_write(mcam, REG_TWSIC0, rval); + (void) mcam_reg_read(mcam, REG_TWSIC1); /* force write */ + rval = value | ((command << TWSIC1_ADDR_SHIFT) & TWSIC1_ADDR); + mcam_reg_write(mcam, REG_TWSIC1, rval); + spin_unlock_irqrestore(&mcam->dev_lock, flags); + + /* Unfortunately, reading TWSIC1 too soon after sending a command + * causes the device to die. + * Use a busy-wait because we often send a large quantity of small + * commands at-once; using msleep() would cause a lot of context + * switches which take longer than 2ms, resulting in a noticeable + * boot-time and capture-start delays. + */ + mdelay(2); + + /* + * Another sad fact is that sometimes, commands silently complete but + * cafe_smbus_write_done() never becomes aware of this. + * This happens at random and appears to possible occur with any + * command. + * We don't understand why this is. We work around this issue + * with the timeout in the wait below, assuming that all commands + * complete within the timeout. + */ + wait_event_timeout(cam->smbus_wait, cafe_smbus_write_done(mcam), + CAFE_SMBUS_TIMEOUT); + + spin_lock_irqsave(&mcam->dev_lock, flags); + rval = mcam_reg_read(mcam, REG_TWSIC1); + spin_unlock_irqrestore(&mcam->dev_lock, flags); + + if (rval & TWSIC1_WSTAT) { + cam_err(cam, "SMBUS write (%02x/%02x/%02x) timed out\n", addr, + command, value); + return -EIO; + } + if (rval & TWSIC1_ERROR) { + cam_err(cam, "SMBUS write (%02x/%02x/%02x) error\n", addr, + command, value); + return -EIO; + } + return 0; +} + + + +static int cafe_smbus_read_done(struct mcam_camera *mcam) +{ + unsigned long flags; + int c1; + + /* + * We must delay after the interrupt, or the controller gets confused + * and never does give us good status. Fortunately, we don't do this + * often. + */ + udelay(20); + spin_lock_irqsave(&mcam->dev_lock, flags); + c1 = mcam_reg_read(mcam, REG_TWSIC1); + spin_unlock_irqrestore(&mcam->dev_lock, flags); + return c1 & (TWSIC1_RVALID|TWSIC1_ERROR); +} + + + +static int cafe_smbus_read_data(struct cafe_camera *cam, + u16 addr, u8 command, u8 *value) +{ + unsigned int rval; + unsigned long flags; + struct mcam_camera *mcam = &cam->mcam; + + spin_lock_irqsave(&mcam->dev_lock, flags); + rval = TWSIC0_EN | ((addr << TWSIC0_SID_SHIFT) & TWSIC0_SID); + rval |= TWSIC0_OVMAGIC; /* Make OV sensors work */ + /* + * Marvel sez set clkdiv to all 1's for now. + */ + rval |= TWSIC0_CLKDIV; + mcam_reg_write(mcam, REG_TWSIC0, rval); + (void) mcam_reg_read(mcam, REG_TWSIC1); /* force write */ + rval = TWSIC1_READ | ((command << TWSIC1_ADDR_SHIFT) & TWSIC1_ADDR); + mcam_reg_write(mcam, REG_TWSIC1, rval); + spin_unlock_irqrestore(&mcam->dev_lock, flags); + + wait_event_timeout(cam->smbus_wait, + cafe_smbus_read_done(mcam), CAFE_SMBUS_TIMEOUT); + spin_lock_irqsave(&mcam->dev_lock, flags); + rval = mcam_reg_read(mcam, REG_TWSIC1); + spin_unlock_irqrestore(&mcam->dev_lock, flags); + + if (rval & TWSIC1_ERROR) { + cam_err(cam, "SMBUS read (%02x/%02x) error\n", addr, command); + return -EIO; + } + if (!(rval & TWSIC1_RVALID)) { + cam_err(cam, "SMBUS read (%02x/%02x) timed out\n", addr, + command); + return -EIO; + } + *value = rval & 0xff; + return 0; +} + +/* + * Perform a transfer over SMBUS. This thing is called under + * the i2c bus lock, so we shouldn't race with ourselves... + */ +static int cafe_smbus_xfer(struct i2c_adapter *adapter, u16 addr, + unsigned short flags, char rw, u8 command, + int size, union i2c_smbus_data *data) +{ + struct cafe_camera *cam = i2c_get_adapdata(adapter); + int ret = -EINVAL; + + /* + * This interface would appear to only do byte data ops. OK + * it can do word too, but the cam chip has no use for that. + */ + if (size != I2C_SMBUS_BYTE_DATA) { + cam_err(cam, "funky xfer size %d\n", size); + return -EINVAL; + } + + if (rw == I2C_SMBUS_WRITE) + ret = cafe_smbus_write_data(cam, addr, command, data->byte); + else if (rw == I2C_SMBUS_READ) + ret = cafe_smbus_read_data(cam, addr, command, &data->byte); + return ret; +} + + +static void cafe_smbus_enable_irq(struct cafe_camera *cam) +{ + unsigned long flags; + + spin_lock_irqsave(&cam->mcam.dev_lock, flags); + mcam_reg_set_bit(&cam->mcam, REG_IRQMASK, TWSIIRQS); + spin_unlock_irqrestore(&cam->mcam.dev_lock, flags); +} + +static u32 cafe_smbus_func(struct i2c_adapter *adapter) +{ + return I2C_FUNC_SMBUS_READ_BYTE_DATA | + I2C_FUNC_SMBUS_WRITE_BYTE_DATA; +} + +static struct i2c_algorithm cafe_smbus_algo = { + .smbus_xfer = cafe_smbus_xfer, + .functionality = cafe_smbus_func +}; + +static int cafe_smbus_setup(struct cafe_camera *cam) +{ + struct i2c_adapter *adap; + int ret; + + adap = kzalloc(sizeof(*adap), GFP_KERNEL); + if (adap == NULL) + return -ENOMEM; + cam->mcam.i2c_adapter = adap; + cafe_smbus_enable_irq(cam); + adap->owner = THIS_MODULE; + adap->algo = &cafe_smbus_algo; + strcpy(adap->name, "cafe_ccic"); + adap->dev.parent = &cam->pdev->dev; + i2c_set_adapdata(adap, cam); + ret = i2c_add_adapter(adap); + if (ret) + printk(KERN_ERR "Unable to register cafe i2c adapter\n"); + return ret; +} + +static void cafe_smbus_shutdown(struct cafe_camera *cam) +{ + i2c_del_adapter(cam->mcam.i2c_adapter); + kfree(cam->mcam.i2c_adapter); +} + + +/* + * Controller-level stuff + */ + +static void cafe_ctlr_init(struct mcam_camera *mcam) +{ + unsigned long flags; + + spin_lock_irqsave(&mcam->dev_lock, flags); + /* + * Added magic to bring up the hardware on the B-Test board + */ + mcam_reg_write(mcam, 0x3038, 0x8); + mcam_reg_write(mcam, 0x315c, 0x80008); + /* + * Go through the dance needed to wake the device up. + * Note that these registers are global and shared + * with the NAND and SD devices. Interaction between the + * three still needs to be examined. + */ + mcam_reg_write(mcam, REG_GL_CSR, GCSR_SRS|GCSR_MRS); /* Needed? */ + mcam_reg_write(mcam, REG_GL_CSR, GCSR_SRC|GCSR_MRC); + mcam_reg_write(mcam, REG_GL_CSR, GCSR_SRC|GCSR_MRS); + /* + * Here we must wait a bit for the controller to come around. + */ + spin_unlock_irqrestore(&mcam->dev_lock, flags); + msleep(5); + spin_lock_irqsave(&mcam->dev_lock, flags); + + mcam_reg_write(mcam, REG_GL_CSR, GCSR_CCIC_EN|GCSR_SRC|GCSR_MRC); + mcam_reg_set_bit(mcam, REG_GL_IMASK, GIMSK_CCIC_EN); + /* + * Mask all interrupts. + */ + mcam_reg_write(mcam, REG_IRQMASK, 0); + spin_unlock_irqrestore(&mcam->dev_lock, flags); +} + + +static void cafe_ctlr_power_up(struct mcam_camera *mcam) +{ + /* + * Part one of the sensor dance: turn the global + * GPIO signal on. + */ + mcam_reg_write(mcam, REG_GL_FCR, GFCR_GPIO_ON); + mcam_reg_write(mcam, REG_GL_GPIOR, GGPIO_OUT|GGPIO_VAL); + /* + * Put the sensor into operational mode (assumes OLPC-style + * wiring). Control 0 is reset - set to 1 to operate. + * Control 1 is power down, set to 0 to operate. + */ + mcam_reg_write(mcam, REG_GPR, GPR_C1EN|GPR_C0EN); /* pwr up, reset */ + mcam_reg_write(mcam, REG_GPR, GPR_C1EN|GPR_C0EN|GPR_C0); +} + +static void cafe_ctlr_power_down(struct mcam_camera *mcam) +{ + mcam_reg_write(mcam, REG_GPR, GPR_C1EN|GPR_C0EN|GPR_C1); + mcam_reg_write(mcam, REG_GL_FCR, GFCR_GPIO_ON); + mcam_reg_write(mcam, REG_GL_GPIOR, GGPIO_OUT); +} + + + +/* + * The platform interrupt handler. + */ +static irqreturn_t cafe_irq(int irq, void *data) +{ + struct cafe_camera *cam = data; + struct mcam_camera *mcam = &cam->mcam; + unsigned int irqs, handled; + + spin_lock(&mcam->dev_lock); + irqs = mcam_reg_read(mcam, REG_IRQSTAT); + handled = cam->registered && mccic_irq(mcam, irqs); + if (irqs & TWSIIRQS) { + mcam_reg_write(mcam, REG_IRQSTAT, TWSIIRQS); + wake_up(&cam->smbus_wait); + handled = 1; + } + spin_unlock(&mcam->dev_lock); + return IRQ_RETVAL(handled); +} + + +/* -------------------------------------------------------------------------- */ +/* + * PCI interface stuff. + */ + +static int cafe_pci_probe(struct pci_dev *pdev, + const struct pci_device_id *id) +{ + int ret; + struct cafe_camera *cam; + struct mcam_camera *mcam; + + /* + * Start putting together one of our big camera structures. + */ + ret = -ENOMEM; + cam = kzalloc(sizeof(struct cafe_camera), GFP_KERNEL); + if (cam == NULL) + goto out; + cam->pdev = pdev; + mcam = &cam->mcam; + mcam->chip_id = V4L2_IDENT_CAFE; + spin_lock_init(&mcam->dev_lock); + init_waitqueue_head(&cam->smbus_wait); + mcam->plat_power_up = cafe_ctlr_power_up; + mcam->plat_power_down = cafe_ctlr_power_down; + mcam->dev = &pdev->dev; + /* + * Set the clock speed for the XO 1; I don't believe this + * driver has ever run anywhere else. + */ + mcam->clock_speed = 45; + mcam->use_smbus = 1; + /* + * Vmalloc mode for buffers is traditional with this driver. + * We *might* be able to run DMA_contig, especially on a system + * with CMA in it. + */ + mcam->buffer_mode = B_vmalloc; + /* + * Get set up on the PCI bus. + */ + ret = pci_enable_device(pdev); + if (ret) + goto out_free; + pci_set_master(pdev); + + ret = -EIO; + mcam->regs = pci_iomap(pdev, 0, 0); + if (!mcam->regs) { + printk(KERN_ERR "Unable to ioremap cafe-ccic regs\n"); + goto out_disable; + } + ret = request_irq(pdev->irq, cafe_irq, IRQF_SHARED, "cafe-ccic", cam); + if (ret) + goto out_iounmap; + + /* + * Initialize the controller and leave it powered up. It will + * stay that way until the sensor driver shows up. + */ + cafe_ctlr_init(mcam); + cafe_ctlr_power_up(mcam); + /* + * Set up I2C/SMBUS communications. We have to drop the mutex here + * because the sensor could attach in this call chain, leading to + * unsightly deadlocks. + */ + ret = cafe_smbus_setup(cam); + if (ret) + goto out_pdown; + + ret = mccic_register(mcam); + if (ret == 0) { + cam->registered = 1; + return 0; + } + + cafe_smbus_shutdown(cam); +out_pdown: + cafe_ctlr_power_down(mcam); + free_irq(pdev->irq, cam); +out_iounmap: + pci_iounmap(pdev, mcam->regs); +out_disable: + pci_disable_device(pdev); +out_free: + kfree(cam); +out: + return ret; +} + + +/* + * Shut down an initialized device + */ +static void cafe_shutdown(struct cafe_camera *cam) +{ + mccic_shutdown(&cam->mcam); + cafe_smbus_shutdown(cam); + free_irq(cam->pdev->irq, cam); + pci_iounmap(cam->pdev, cam->mcam.regs); +} + + +static void cafe_pci_remove(struct pci_dev *pdev) +{ + struct v4l2_device *v4l2_dev = dev_get_drvdata(&pdev->dev); + struct cafe_camera *cam = to_cam(v4l2_dev); + + if (cam == NULL) { + printk(KERN_WARNING "pci_remove on unknown pdev %p\n", pdev); + return; + } + cafe_shutdown(cam); + kfree(cam); +} + + +#ifdef CONFIG_PM +/* + * Basic power management. + */ +static int cafe_pci_suspend(struct pci_dev *pdev, pm_message_t state) +{ + struct v4l2_device *v4l2_dev = dev_get_drvdata(&pdev->dev); + struct cafe_camera *cam = to_cam(v4l2_dev); + int ret; + + ret = pci_save_state(pdev); + if (ret) + return ret; + mccic_suspend(&cam->mcam); + pci_disable_device(pdev); + return 0; +} + + +static int cafe_pci_resume(struct pci_dev *pdev) +{ + struct v4l2_device *v4l2_dev = dev_get_drvdata(&pdev->dev); + struct cafe_camera *cam = to_cam(v4l2_dev); + int ret = 0; + + pci_restore_state(pdev); + ret = pci_enable_device(pdev); + + if (ret) { + cam_warn(cam, "Unable to re-enable device on resume!\n"); + return ret; + } + cafe_ctlr_init(&cam->mcam); + return mccic_resume(&cam->mcam); +} + +#endif /* CONFIG_PM */ + +static struct pci_device_id cafe_ids[] = { + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, + PCI_DEVICE_ID_MARVELL_88ALP01_CCIC) }, + { 0, } +}; + +MODULE_DEVICE_TABLE(pci, cafe_ids); + +static struct pci_driver cafe_pci_driver = { + .name = "cafe1000-ccic", + .id_table = cafe_ids, + .probe = cafe_pci_probe, + .remove = cafe_pci_remove, +#ifdef CONFIG_PM + .suspend = cafe_pci_suspend, + .resume = cafe_pci_resume, +#endif +}; + + + + +static int __init cafe_init(void) +{ + int ret; + + printk(KERN_NOTICE "Marvell M88ALP01 'CAFE' Camera Controller version %d\n", + CAFE_VERSION); + ret = pci_register_driver(&cafe_pci_driver); + if (ret) { + printk(KERN_ERR "Unable to register cafe_ccic driver\n"); + goto out; + } + ret = 0; + +out: + return ret; +} + + +static void __exit cafe_exit(void) +{ + pci_unregister_driver(&cafe_pci_driver); +} + +module_init(cafe_init); +module_exit(cafe_exit); |