diff options
Diffstat (limited to 'drivers/input/touchscreen')
| -rw-r--r-- | drivers/input/touchscreen/Kconfig | 9 | ||||
| -rw-r--r-- | drivers/input/touchscreen/ad7877.c | 2 | ||||
| -rw-r--r-- | drivers/input/touchscreen/ads7846.c | 20 |
3 files changed, 26 insertions, 5 deletions
diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig index 7208654a94a..8a8fa4d2d6a 100644 --- a/drivers/input/touchscreen/Kconfig +++ b/drivers/input/touchscreen/Kconfig @@ -24,17 +24,18 @@ config TOUCHSCREEN_88PM860X module will be called 88pm860x-ts. config TOUCHSCREEN_ADS7846 - tristate "ADS7846/TSC2046 and ADS7843 based touchscreens" + tristate "ADS7846/TSC2046/AD7873 and AD(S)7843 based touchscreens" depends on SPI_MASTER depends on HWMON = n || HWMON help Say Y here if you have a touchscreen interface using the - ADS7846/TSC2046 or ADS7843 controller, and your board-specific - setup code includes that in its table of SPI devices. + ADS7846/TSC2046/AD7873 or ADS7843/AD7843 controller, + and your board-specific setup code includes that in its + table of SPI devices. If HWMON is selected, and the driver is told the reference voltage on your board, you will also get hwmon interfaces for the voltage - (and on ads7846/tsc2046, temperature) sensors of this chip. + (and on ads7846/tsc2046/ad7873, temperature) sensors of this chip. If unsure, say N (but it's safe to say "Y"). diff --git a/drivers/input/touchscreen/ad7877.c b/drivers/input/touchscreen/ad7877.c index eb83939c705..e019d53d1ab 100644 --- a/drivers/input/touchscreen/ad7877.c +++ b/drivers/input/touchscreen/ad7877.c @@ -46,7 +46,7 @@ #include <linux/spi/ad7877.h> #include <asm/irq.h> -#define TS_PEN_UP_TIMEOUT msecs_to_jiffies(50) +#define TS_PEN_UP_TIMEOUT msecs_to_jiffies(100) #define MAX_SPI_FREQ_HZ 20000000 #define MAX_12BIT ((1<<12)-1) diff --git a/drivers/input/touchscreen/ads7846.c b/drivers/input/touchscreen/ads7846.c index 8b05d8e9754..532279cda0e 100644 --- a/drivers/input/touchscreen/ads7846.c +++ b/drivers/input/touchscreen/ads7846.c @@ -36,6 +36,7 @@ * TSC2046 is just newer ads7846 silicon. * Support for ads7843 tested on Atmel at91sam926x-EK. * Support for ads7845 has only been stubbed in. + * Support for Analog Devices AD7873 and AD7843 tested. * * IRQ handling needs a workaround because of a shortcoming in handling * edge triggered IRQs on some platforms like the OMAP1/2. These @@ -821,6 +822,9 @@ static int ads7846_suspend(struct spi_device *spi, pm_message_t message) spin_unlock_irq(&ts->lock); + if (device_may_wakeup(&ts->spi->dev)) + enable_irq_wake(ts->spi->irq); + return 0; } @@ -829,6 +833,9 @@ static int ads7846_resume(struct spi_device *spi) { struct ads7846 *ts = dev_get_drvdata(&spi->dev); + if (device_may_wakeup(&ts->spi->dev)) + disable_irq_wake(ts->spi->irq); + spin_lock_irq(&ts->lock); ts->is_suspended = 0; @@ -984,6 +991,15 @@ static int __devinit ads7846_probe(struct spi_device *spi) vref = pdata->keep_vref_on; + if (ts->model == 7873) { + /* The AD7873 is almost identical to the ADS7846 + * keep VREF off during differential/ratiometric + * conversion modes + */ + ts->model = 7846; + vref = 0; + } + /* set up the transfers to read touchscreen state; this assumes we * use formula #2 for pressure, not #3. */ @@ -1191,6 +1207,8 @@ static int __devinit ads7846_probe(struct spi_device *spi) if (err) goto err_remove_attr_group; + device_init_wakeup(&spi->dev, pdata->wakeup); + return 0; err_remove_attr_group: @@ -1220,6 +1238,8 @@ static int __devexit ads7846_remove(struct spi_device *spi) { struct ads7846 *ts = dev_get_drvdata(&spi->dev); + device_init_wakeup(&spi->dev, false); + ads784x_hwmon_unregister(spi, ts); input_unregister_device(ts->input); |