1 files changed, 197 insertions, 115 deletions

diff --git a/drivers/infiniband/hw/ipath/ipath_init_chip.c b/drivers/infiniband/hw/ipath/ipath_init_chip.c
index 4471674975c..27dd8947666 100644
--- a/drivers/infiniband/hw/ipath/ipath_init_chip.c
+++ b/drivers/infiniband/hw/ipath/ipath_init_chip.c
@@ -1,5 +1,5 @@
 /*
- * Copyright (c) 2006, 2007 QLogic Corporation. All rights reserved.
+ * Copyright (c) 2006, 2007, 2008 QLogic Corporation. All rights reserved.
  * Copyright (c) 2003, 2004, 2005, 2006 PathScale, Inc. All rights reserved.
  *
  * This software is available to you under a choice of one of two
@@ -155,24 +155,13 @@ static int bringup_link(struct ipath_devdata *dd)
 			 dd->ipath_control);
 
 	/*
-	 * Note that prior to try 14 or 15 of IB, the credit scaling
-	 * wasn't working, because it was swapped for writes with the
-	 * 1 bit default linkstate field
+	 * set initial max size pkt IBC will send, including ICRC; it's the
+	 * PIO buffer size in dwords, less 1; also see ipath_set_mtu()
 	 */
+	val = (dd->ipath_ibmaxlen >> 2) + 1;
+	ibc = val << dd->ibcc_mpl_shift;
 
-	/* ignore pbc and align word */
-	val = dd->ipath_piosize2k - 2 * sizeof(u32);
-	/*
-	 * for ICRC, which we only send in diag test pkt mode, and we
-	 * don't need to worry about that for mtu
-	 */
-	val += 1;
-	/*
-	 * Set the IBC maxpktlength to the size of our pio buffers the
-	 * maxpktlength is in words.  This is *not* the IB data MTU.
-	 */
-	ibc = (val / sizeof(u32)) << INFINIPATH_IBCC_MAXPKTLEN_SHIFT;
-	/* in KB */
+	/* flowcontrolwatermark is in units of KBytes */
 	ibc |= 0x5ULL << INFINIPATH_IBCC_FLOWCTRLWATERMARK_SHIFT;
 	/*
 	 * How often flowctrl sent.  More or less in usecs; balance against
@@ -191,10 +180,13 @@ static int bringup_link(struct ipath_devdata *dd)
 	/*
 	 * Want to start out with both LINKCMD and LINKINITCMD in NOP
 	 * (0 and 0).  Don't put linkinitcmd in ipath_ibcctrl, want that
-	 * to stay a NOP
+	 * to stay a NOP. Flag that we are disabled, for the (unlikely)
+	 * case that some recovery path is trying to bring the link up
+	 * before we are ready.
 	 */
 	ibc |= INFINIPATH_IBCC_LINKINITCMD_DISABLE <<
 		INFINIPATH_IBCC_LINKINITCMD_SHIFT;
+	dd->ipath_flags |= IPATH_IB_LINK_DISABLED;
 	ipath_cdbg(VERBOSE, "Writing 0x%llx to ibcctrl\n",
 		   (unsigned long long) ibc);
 	ipath_write_kreg(dd, dd->ipath_kregs->kr_ibcctrl, ibc);
@@ -227,17 +219,26 @@ static struct ipath_portdata *create_portdata0(struct ipath_devdata *dd)
 		pd->port_cnt = 1;
 		/* The port 0 pkey table is used by the layer interface. */
 		pd->port_pkeys[0] = IPATH_DEFAULT_P_KEY;
+		pd->port_seq_cnt = 1;
 	}
 	return pd;
 }
 
-static int init_chip_first(struct ipath_devdata *dd,
-			   struct ipath_portdata **pdp)
+static int init_chip_first(struct ipath_devdata *dd)
 {
-	struct ipath_portdata *pd = NULL;
+	struct ipath_portdata *pd;
 	int ret = 0;
 	u64 val;
 
+	spin_lock_init(&dd->ipath_kernel_tid_lock);
+	spin_lock_init(&dd->ipath_user_tid_lock);
+	spin_lock_init(&dd->ipath_sendctrl_lock);
+	spin_lock_init(&dd->ipath_sdma_lock);
+	spin_lock_init(&dd->ipath_gpio_lock);
+	spin_lock_init(&dd->ipath_eep_st_lock);
+	spin_lock_init(&dd->ipath_sdepb_lock);
+	mutex_init(&dd->ipath_eep_lock);
+
 	/*
 	 * skip cfgports stuff because we are not allocating memory,
 	 * and we don't want problems if the portcnt changed due to
@@ -250,12 +251,14 @@ static int init_chip_first(struct ipath_devdata *dd,
 	else if (ipath_cfgports <= dd->ipath_portcnt) {
 		dd->ipath_cfgports = ipath_cfgports;
 		ipath_dbg("Configured to use %u ports out of %u in chip\n",
-			  dd->ipath_cfgports, dd->ipath_portcnt);
+			  dd->ipath_cfgports, ipath_read_kreg32(dd,
+			  dd->ipath_kregs->kr_portcnt));
 	} else {
 		dd->ipath_cfgports = dd->ipath_portcnt;
 		ipath_dbg("Tried to configured to use %u ports; chip "
 			  "only supports %u\n", ipath_cfgports,
-			  dd->ipath_portcnt);
+			  ipath_read_kreg32(dd,
+				  dd->ipath_kregs->kr_portcnt));
 	}
 	/*
 	 * Allocate full portcnt array, rather than just cfgports, because
@@ -295,12 +298,9 @@ static int init_chip_first(struct ipath_devdata *dd,
 	val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_sendpiosize);
 	dd->ipath_piosize2k = val & ~0U;
 	dd->ipath_piosize4k = val >> 32;
-	/*
-	 * Note: the chips support a maximum MTU of 4096, but the driver
-	 * hasn't implemented this feature yet, so set the initial value
-	 * to 2048.
-	 */
-	dd->ipath_ibmtu = 2048;
+	if (dd->ipath_piosize4k == 0 && ipath_mtu4096)
+		ipath_mtu4096 = 0; /* 4KB not supported by this chip */
+	dd->ipath_ibmtu = ipath_mtu4096 ? 4096 : 2048;
 	val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_sendpiobufcnt);
 	dd->ipath_piobcnt2k = val & ~0U;
 	dd->ipath_piobcnt4k = val >> 32;
@@ -328,43 +328,46 @@ static int init_chip_first(struct ipath_devdata *dd,
 	else ipath_dbg("%u 2k piobufs @ %p\n",
 		       dd->ipath_piobcnt2k, dd->ipath_pio2kbase);
 
-	spin_lock_init(&dd->ipath_tid_lock);
-	spin_lock_init(&dd->ipath_sendctrl_lock);
-	spin_lock_init(&dd->ipath_gpio_lock);
-	spin_lock_init(&dd->ipath_eep_st_lock);
-	mutex_init(&dd->ipath_eep_lock);
-
 done:
-	*pdp = pd;
 	return ret;
 }
 
 /**
  * init_chip_reset - re-initialize after a reset, or enable
  * @dd: the infinipath device
- * @pdp: output for port data
  *
  * sanity check at least some of the values after reset, and
  * ensure no receive or transmit (explictly, in case reset
  * failed
  */
-static int init_chip_reset(struct ipath_devdata *dd,
-			   struct ipath_portdata **pdp)
+static int init_chip_reset(struct ipath_devdata *dd)
 {
 	u32 rtmp;
+	int i;
+	unsigned long flags;
+
+	/*
+	 * ensure chip does no sends or receives, tail updates, or
+	 * pioavail updates while we re-initialize
+	 */
+	dd->ipath_rcvctrl &= ~(1ULL << dd->ipath_r_tailupd_shift);
+	for (i = 0; i < dd->ipath_portcnt; i++) {
+		clear_bit(dd->ipath_r_portenable_shift + i,
+			  &dd->ipath_rcvctrl);
+		clear_bit(dd->ipath_r_intravail_shift + i,
+			  &dd->ipath_rcvctrl);
+	}
+	ipath_write_kreg(dd, dd->ipath_kregs->kr_rcvctrl,
+		dd->ipath_rcvctrl);
 
-	*pdp = dd->ipath_pd[0];
-	/* ensure chip does no sends or receives while we re-initialize */
-	dd->ipath_control = dd->ipath_sendctrl = dd->ipath_rcvctrl = 0U;
-	ipath_write_kreg(dd, dd->ipath_kregs->kr_rcvctrl, dd->ipath_rcvctrl);
+	spin_lock_irqsave(&dd->ipath_sendctrl_lock, flags);
+	dd->ipath_sendctrl = 0U; /* no sdma, etc */
 	ipath_write_kreg(dd, dd->ipath_kregs->kr_sendctrl, dd->ipath_sendctrl);
-	ipath_write_kreg(dd, dd->ipath_kregs->kr_control, dd->ipath_control);
+	ipath_read_kreg64(dd, dd->ipath_kregs->kr_scratch);
+	spin_unlock_irqrestore(&dd->ipath_sendctrl_lock, flags);
+
+	ipath_write_kreg(dd, dd->ipath_kregs->kr_control, 0ULL);
 
-	rtmp = ipath_read_kreg32(dd, dd->ipath_kregs->kr_portcnt);
-	if (dd->ipath_portcnt != rtmp)
-		dev_info(&dd->pcidev->dev, "portcnt was %u before "
-			 "reset, now %u, using original\n",
-			 dd->ipath_portcnt, rtmp);
 	rtmp = ipath_read_kreg32(dd, dd->ipath_kregs->kr_rcvtidcnt);
 	if (rtmp != dd->ipath_rcvtidcnt)
 		dev_info(&dd->pcidev->dev, "tidcnt was %u before "
@@ -467,10 +470,10 @@ static void init_shadow_tids(struct ipath_devdata *dd)
 	dd->ipath_physshadow = addrs;
 }
 
-static void enable_chip(struct ipath_devdata *dd,
-			struct ipath_portdata *pd, int reinit)
+static void enable_chip(struct ipath_devdata *dd, int reinit)
 {
 	u32 val;
+	u64 rcvmask;
 	unsigned long flags;
 	int i;
 
@@ -484,17 +487,28 @@ static void enable_chip(struct ipath_devdata *dd,
 	/* Enable PIO send, and update of PIOavail regs to memory. */
 	dd->ipath_sendctrl = INFINIPATH_S_PIOENABLE |
 		INFINIPATH_S_PIOBUFAVAILUPD;
+
+	/*
+	 * Set the PIO avail update threshold to host memory
+	 * on chips that support it.
+	 */
+	if (dd->ipath_pioupd_thresh)
+		dd->ipath_sendctrl |= dd->ipath_pioupd_thresh
+			<< INFINIPATH_S_UPDTHRESH_SHIFT;
 	ipath_write_kreg(dd, dd->ipath_kregs->kr_sendctrl, dd->ipath_sendctrl);
 	ipath_read_kreg64(dd, dd->ipath_kregs->kr_scratch);
 	spin_unlock_irqrestore(&dd->ipath_sendctrl_lock, flags);
 
 	/*
-	 * enable port 0 receive, and receive interrupt.  other ports
-	 * done as user opens and inits them.
+	 * Enable kernel ports' receive and receive interrupt.
+	 * Other ports done as user opens and inits them.
 	 */
-	dd->ipath_rcvctrl = (1ULL << dd->ipath_r_tailupd_shift) |
-		(1ULL << dd->ipath_r_portenable_shift) |
-		(1ULL << dd->ipath_r_intravail_shift);
+	rcvmask = 1ULL;
+	dd->ipath_rcvctrl |= (rcvmask << dd->ipath_r_portenable_shift) |
+		(rcvmask << dd->ipath_r_intravail_shift);
+	if (!(dd->ipath_flags & IPATH_NODMA_RTAIL))
+		dd->ipath_rcvctrl |= (1ULL << dd->ipath_r_tailupd_shift);
+
 	ipath_write_kreg(dd, dd->ipath_kregs->kr_rcvctrl,
 			 dd->ipath_rcvctrl);
 
@@ -505,16 +519,16 @@ static void enable_chip(struct ipath_devdata *dd,
 	dd->ipath_flags |= IPATH_INITTED;
 
 	/*
-	 * init our shadow copies of head from tail values, and write
-	 * head values to match.
+	 * Init our shadow copies of head from tail values,
+	 * and write head values to match.
 	 */
 	val = ipath_read_ureg32(dd, ur_rcvegrindextail, 0);
-	(void)ipath_write_ureg(dd, ur_rcvegrindexhead, val, 0);
+	ipath_write_ureg(dd, ur_rcvegrindexhead, val, 0);
 
 	/* Initialize so we interrupt on next packet received */
-	(void)ipath_write_ureg(dd, ur_rcvhdrhead,
-			       dd->ipath_rhdrhead_intr_off |
-			       dd->ipath_pd[0]->port_head, 0);
+	ipath_write_ureg(dd, ur_rcvhdrhead,
+			 dd->ipath_rhdrhead_intr_off |
+			 dd->ipath_pd[0]->port_head, 0);
 
 	/*
 	 * by now pioavail updates to memory should have occurred, so
@@ -523,25 +537,26 @@ static void enable_chip(struct ipath_devdata *dd,
 	 * initial values of the generation bit correct.
 	 */
 	for (i = 0; i < dd->ipath_pioavregs; i++) {
-		__le64 val;
+		__le64 pioavail;
 
 		/*
 		 * Chip Errata bug 6641; even and odd qwords>3 are swapped.
 		 */
 		if (i > 3 && (dd->ipath_flags & IPATH_SWAP_PIOBUFS))
-			val = dd->ipath_pioavailregs_dma[i ^ 1];
+			pioavail = dd->ipath_pioavailregs_dma[i ^ 1];
 		else
-			val = dd->ipath_pioavailregs_dma[i];
-		dd->ipath_pioavailshadow[i] = le64_to_cpu(val);
+			pioavail = dd->ipath_pioavailregs_dma[i];
+		dd->ipath_pioavailshadow[i] = le64_to_cpu(pioavail) |
+			(~dd->ipath_pioavailkernel[i] <<
+			INFINIPATH_SENDPIOAVAIL_BUSY_SHIFT);
 	}
 	/* can get counters, stats, etc. */
 	dd->ipath_flags |= IPATH_PRESENT;
 }
 
-static int init_housekeeping(struct ipath_devdata *dd,
-			     struct ipath_portdata **pdp, int reinit)
+static int init_housekeeping(struct ipath_devdata *dd, int reinit)
 {
-	char boardn[32];
+	char boardn[40];
 	int ret = 0;
 
 	/*
@@ -600,18 +615,9 @@ static int init_housekeeping(struct ipath_devdata *dd,
 	ipath_write_kreg(dd, dd->ipath_kregs->kr_errorclear,
 			 INFINIPATH_E_RESET);
 
-	if (reinit)
-		ret = init_chip_reset(dd, pdp);
-	else
-		ret = init_chip_first(dd, pdp);
-
-	if (ret)
-		goto done;
-
-	ipath_cdbg(VERBOSE, "Revision %llx (PCI %x), %u ports, %u tids, "
-		   "%u egrtids\n", (unsigned long long) dd->ipath_revision,
-		   dd->ipath_pcirev, dd->ipath_portcnt, dd->ipath_rcvtidcnt,
-		   dd->ipath_rcvegrcnt);
+	ipath_cdbg(VERBOSE, "Revision %llx (PCI %x)\n",
+		   (unsigned long long) dd->ipath_revision,
+		   dd->ipath_pcirev);
 
 	if (((dd->ipath_revision >> INFINIPATH_R_SOFTWARE_SHIFT) &
 	     INFINIPATH_R_SOFTWARE_MASK) != IPATH_CHIP_SWVERSION) {
@@ -650,10 +656,39 @@ static int init_housekeeping(struct ipath_devdata *dd,
 
 	ipath_dbg("%s", dd->ipath_boardversion);
 
+	if (ret)
+		goto done;
+
+	if (reinit)
+		ret = init_chip_reset(dd);
+	else
+		ret = init_chip_first(dd);
+
 done:
 	return ret;
 }
 
+static void verify_interrupt(unsigned long opaque)
+{
+	struct ipath_devdata *dd = (struct ipath_devdata *) opaque;
+
+	if (!dd)
+		return; /* being torn down */
+
+	/*
+	 * If we don't have any interrupts, let the user know and
+	 * don't bother checking again.
+	 */
+	if (dd->ipath_int_counter == 0) {
+		if (!dd->ipath_f_intr_fallback(dd))
+			dev_err(&dd->pcidev->dev, "No interrupts detected, "
+				"not usable.\n");
+		else /* re-arm the timer to see if fallback works */
+			mod_timer(&dd->ipath_intrchk_timer, jiffies + HZ/2);
+	} else
+		ipath_cdbg(VERBOSE, "%u interrupts at timer check\n",
+			dd->ipath_int_counter);
+}
 
 /**
  * ipath_init_chip - do the actual initialization sequence on the chip
@@ -676,11 +711,11 @@ int ipath_init_chip(struct ipath_devdata *dd, int reinit)
 	u32 val32, kpiobufs;
 	u32 piobufs, uports;
 	u64 val;
-	struct ipath_portdata *pd = NULL; /* keep gcc4 happy */
+	struct ipath_portdata *pd;
 	gfp_t gfp_flags = GFP_USER | __GFP_COMP;
 	unsigned long flags;
 
-	ret = init_housekeeping(dd, &pd, reinit);
+	ret = init_housekeeping(dd, reinit);
 	if (ret)
 		goto done;
 
@@ -700,7 +735,7 @@ int ipath_init_chip(struct ipath_devdata *dd, int reinit)
 	 * we now use routines that backend onto __get_free_pages, the
 	 * rest would be wasted.
 	 */
-	dd->ipath_rcvhdrcnt = dd->ipath_rcvegrcnt;
+	dd->ipath_rcvhdrcnt = max(dd->ipath_p0_rcvegrcnt, dd->ipath_rcvegrcnt);
 	ipath_write_kreg(dd, dd->ipath_kregs->kr_rcvhdrcnt,
 			 dd->ipath_rcvhdrcnt);
 
@@ -731,8 +766,8 @@ int ipath_init_chip(struct ipath_devdata *dd, int reinit)
 	if (kpiobufs + (uports * IPATH_MIN_USER_PORT_BUFCNT) > piobufs) {
 		int i = (int) piobufs -
 			(int) (uports * IPATH_MIN_USER_PORT_BUFCNT);
-		if (i < 0)
-			i = 0;
+		if (i < 1)
+			i = 1;
 		dev_info(&dd->pcidev->dev, "Allocating %d PIO bufs of "
 			 "%d for kernel leaves too few for %d user ports "
 			 "(%d each); using %u\n", kpiobufs,
@@ -751,24 +786,40 @@ int ipath_init_chip(struct ipath_devdata *dd, int reinit)
 		ipath_dbg("allocating %u pbufs/port leaves %u unused, "
 			  "add to kernel\n", dd->ipath_pbufsport, val32);
 		dd->ipath_lastport_piobuf -= val32;
+		kpiobufs += val32;
 		ipath_dbg("%u pbufs/port leaves %u unused, add to kernel\n",
 			  dd->ipath_pbufsport, val32);
 	}
-	dd->ipath_lastpioindex = dd->ipath_lastport_piobuf;
+	dd->ipath_lastpioindex = 0;
+	dd->ipath_lastpioindexl = dd->ipath_piobcnt2k;
+	ipath_chg_pioavailkernel(dd, 0, piobufs, 1);
 	ipath_cdbg(VERBOSE, "%d PIO bufs for kernel out of %d total %u "
 		   "each for %u user ports\n", kpiobufs,
 		   piobufs, dd->ipath_pbufsport, uports);
+	if (dd->ipath_pioupd_thresh) {
+		if (dd->ipath_pbufsport < dd->ipath_pioupd_thresh)
+			dd->ipath_pioupd_thresh = dd->ipath_pbufsport;
+		if (kpiobufs < dd->ipath_pioupd_thresh)
+			dd->ipath_pioupd_thresh = kpiobufs;
+	}
+
+	ret = dd->ipath_f_early_init(dd);
+	if (ret) {
+		ipath_dev_err(dd, "Early initialization failure\n");
+		goto done;
+	}
 
-	dd->ipath_f_early_init(dd);
 	/*
-	 * cancel any possible active sends from early driver load.
+	 * Cancel any possible active sends from early driver load.
 	 * Follows early_init because some chips have to initialize
 	 * PIO buffers in early_init to avoid false parity errors.
 	 */
 	ipath_cancel_sends(dd, 0);
 
-	/* early_init sets rcvhdrentsize and rcvhdrsize, so this must be
-	 * done after early_init */
+	/*
+	 * Early_init sets rcvhdrentsize and rcvhdrsize, so this must be
+	 * done after early_init.
+	 */
 	dd->ipath_hdrqlast =
 		dd->ipath_rcvhdrentsize * (dd->ipath_rcvhdrcnt - 1);
 	ipath_write_kreg(dd, dd->ipath_kregs->kr_rcvhdrentsize,
@@ -783,8 +834,8 @@ int ipath_init_chip(struct ipath_devdata *dd, int reinit)
 			goto done;
 	}
 
-	(void)ipath_write_kreg(dd, dd->ipath_kregs->kr_sendpioavailaddr,
-			       dd->ipath_pioavailregs_phys);
+	ipath_write_kreg(dd, dd->ipath_kregs->kr_sendpioavailaddr,
+			 dd->ipath_pioavailregs_phys);
 	/*
 	 * this is to detect s/w errors, which the h/w works around by
 	 * ignoring the low 6 bits of address, if it wasn't aligned.
@@ -843,58 +894,65 @@ int ipath_init_chip(struct ipath_devdata *dd, int reinit)
 	/* enable errors that are masked, at least this first time. */
 	ipath_write_kreg(dd, dd->ipath_kregs->kr_errormask,
 			 ~dd->ipath_maskederrs);
-	dd->ipath_errormask = ipath_read_kreg64(dd,
-		dd->ipath_kregs->kr_errormask);
+	dd->ipath_maskederrs = 0; /* don't re-enable ignored in timer */
+	dd->ipath_errormask =
+		ipath_read_kreg64(dd, dd->ipath_kregs->kr_errormask);
 	/* clear any interrupts up to this point (ints still not enabled) */
 	ipath_write_kreg(dd, dd->ipath_kregs->kr_intclear, -1LL);
 
+	dd->ipath_f_tidtemplate(dd);
+
 	/*
 	 * Set up the port 0 (kernel) rcvhdr q and egr TIDs.  If doing
 	 * re-init, the simplest way to handle this is to free
 	 * existing, and re-allocate.
 	 * Need to re-create rest of port 0 portdata as well.
 	 */
+	pd = dd->ipath_pd[0];
 	if (reinit) {
-		/* Alloc and init new ipath_portdata for port0,
+		struct ipath_portdata *npd;
+
+		/*
+		 * Alloc and init new ipath_portdata for port0,
 		 * Then free old pd. Could lead to fragmentation, but also
 		 * makes later support for hot-swap easier.
 		 */
-		struct ipath_portdata *npd;
 		npd = create_portdata0(dd);
 		if (npd) {
 			ipath_free_pddata(dd, pd);
-			dd->ipath_pd[0] = pd = npd;
+			dd->ipath_pd[0] = npd;
+			pd = npd;
 		} else {
-			ipath_dev_err(dd, "Unable to allocate portdata for"
-				      "  port 0, failing\n");
+			ipath_dev_err(dd, "Unable to allocate portdata"
+				      " for port 0, failing\n");
 			ret = -ENOMEM;
 			goto done;
 		}
 	}
-	dd->ipath_f_tidtemplate(dd);
 	ret = ipath_create_rcvhdrq(dd, pd);
-	if (!ret) {
-		dd->ipath_hdrqtailptr =
-			(volatile __le64 *)pd->port_rcvhdrtail_kvaddr;
+	if (!ret)
 		ret = create_port0_egr(dd);
-	}
-	if (ret)
-		ipath_dev_err(dd, "failed to allocate port 0 (kernel) "
+	if (ret) {
+		ipath_dev_err(dd, "failed to allocate kernel port's "
 			      "rcvhdrq and/or egr bufs\n");
+		goto done;
+	}
 	else
-		enable_chip(dd, pd, reinit);
-
+		enable_chip(dd, reinit);
 
-	if (!ret && !reinit) {
-	    /* used when we close a port, for DMA already in flight at close */
+	if (!reinit) {
+		/*
+		 * Used when we close a port, for DMA already in flight
+		 * at close.
+		 */
 		dd->ipath_dummy_hdrq = dma_alloc_coherent(
-			&dd->pcidev->dev, pd->port_rcvhdrq_size,
+			&dd->pcidev->dev, dd->ipath_pd[0]->port_rcvhdrq_size,
 			&dd->ipath_dummy_hdrq_phys,
 			gfp_flags);
-		if (!dd->ipath_dummy_hdrq ) {
+		if (!dd->ipath_dummy_hdrq) {
 			dev_info(&dd->pcidev->dev,
 				"Couldn't allocate 0x%lx bytes for dummy hdrq\n",
-				pd->port_rcvhdrq_size);
+				dd->ipath_pd[0]->port_rcvhdrq_size);
 			/* fallback to just 0'ing */
 			dd->ipath_dummy_hdrq_phys = 0UL;
 		}
@@ -906,7 +964,7 @@ int ipath_init_chip(struct ipath_devdata *dd, int reinit)
 	 */
 	ipath_write_kreg(dd, dd->ipath_kregs->kr_intclear, 0ULL);
 
-	if(!dd->ipath_stats_timer_active) {
+	if (!dd->ipath_stats_timer_active) {
 		/*
 		 * first init, or after an admin disable/enable
 		 * set up stats retrieval timer, even if we had errors
@@ -922,6 +980,16 @@ int ipath_init_chip(struct ipath_devdata *dd, int reinit)
 		dd->ipath_stats_timer_active = 1;
 	}
 
+	/* Set up SendDMA if chip supports it */
+	if (dd->ipath_flags & IPATH_HAS_SEND_DMA)
+		ret = setup_sdma(dd);
+
+	/* Set up HoL state */
+	init_timer(&dd->ipath_hol_timer);
+	dd->ipath_hol_timer.function = ipath_hol_event;
+	dd->ipath_hol_timer.data = (unsigned long)dd;
+	dd->ipath_hol_state = IPATH_HOL_UP;
+
 done:
 	if (!ret) {
 		*dd->ipath_statusp |= IPATH_STATUS_CHIP_PRESENT;
@@ -934,6 +1002,20 @@ done:
 					 0ULL);
 			/* chip is usable; mark it as initialized */
 			*dd->ipath_statusp |= IPATH_STATUS_INITTED;
+
+			/*
+			 * setup to verify we get an interrupt, and fallback
+			 * to an alternate if necessary and possible
+			 */
+			if (!reinit) {
+				init_timer(&dd->ipath_intrchk_timer);
+				dd->ipath_intrchk_timer.function =
+					verify_interrupt;
+				dd->ipath_intrchk_timer.data =
+					(unsigned long) dd;
+			}
+			dd->ipath_intrchk_timer.expires = jiffies + HZ/2;
+			add_timer(&dd->ipath_intrchk_timer);
 		} else
 			ipath_dev_err(dd, "No interrupts enabled, couldn't "
 				      "setup interrupt address\n");