1 files changed, 182 insertions, 81 deletions

diff --git a/drivers/infiniband/hw/ipath/ipath_iba6120.c b/drivers/infiniband/hw/ipath/ipath_iba6120.c
index d86516d23df..a72ab9de386 100644
--- a/drivers/infiniband/hw/ipath/ipath_iba6120.c
+++ b/drivers/infiniband/hw/ipath/ipath_iba6120.c
@@ -263,8 +263,8 @@ static const struct ipath_cregs ipath_pe_cregs = {
 };
 
 /* kr_intstatus, kr_intclear, kr_intmask bits */
-#define INFINIPATH_I_RCVURG_MASK 0x1F
-#define INFINIPATH_I_RCVAVAIL_MASK 0x1F
+#define INFINIPATH_I_RCVURG_MASK ((1U<<5)-1)
+#define INFINIPATH_I_RCVAVAIL_MASK ((1U<<5)-1)
 
 /* kr_hwerrclear, kr_hwerrmask, kr_hwerrstatus, bits */
 #define INFINIPATH_HWE_PCIEMEMPARITYERR_MASK  0x000000000000003fULL
@@ -294,6 +294,33 @@ static const struct ipath_cregs ipath_pe_cregs = {
 #define IPATH_GPIO_SCL (1ULL << \
 	(_IPATH_GPIO_SCL_NUM+INFINIPATH_EXTC_GPIOOE_SHIFT))
 
+/*
+ * Rev2 silicon allows suppressing check for ArmLaunch errors.
+ * this can speed up short packet sends on systems that do
+ * not guaranteee write-order.
+ */
+#define INFINIPATH_XGXS_SUPPRESS_ARMLAUNCH_ERR (1ULL<<63)
+
+/* 6120 specific hardware errors... */
+static const struct ipath_hwerror_msgs ipath_6120_hwerror_msgs[] = {
+	INFINIPATH_HWE_MSG(PCIEPOISONEDTLP, "PCIe Poisoned TLP"),
+	INFINIPATH_HWE_MSG(PCIECPLTIMEOUT, "PCIe completion timeout"),
+	/*
+	 * In practice, it's unlikely wthat we'll see PCIe PLL, or bus
+	 * parity or memory parity error failures, because most likely we
+	 * won't be able to talk to the core of the chip.  Nonetheless, we
+	 * might see them, if they are in parts of the PCIe core that aren't
+	 * essential.
+	 */
+	INFINIPATH_HWE_MSG(PCIE1PLLFAILED, "PCIePLL1"),
+	INFINIPATH_HWE_MSG(PCIE0PLLFAILED, "PCIePLL0"),
+	INFINIPATH_HWE_MSG(PCIEBUSPARITYXTLH, "PCIe XTLH core parity"),
+	INFINIPATH_HWE_MSG(PCIEBUSPARITYXADM, "PCIe ADM TX core parity"),
+	INFINIPATH_HWE_MSG(PCIEBUSPARITYRADM, "PCIe ADM RX core parity"),
+	INFINIPATH_HWE_MSG(RXDSYNCMEMPARITYERR, "Rx Dsync"),
+	INFINIPATH_HWE_MSG(SERDESPLLFAILED, "SerDes PLL"),
+};
+
 /**
  * ipath_pe_handle_hwerrors - display hardware errors.
  * @dd: the infinipath device
@@ -343,19 +370,49 @@ static void ipath_pe_handle_hwerrors(struct ipath_devdata *dd, char *msg,
 	 * make sure we get this much out, unless told to be quiet,
 	 * or it's occurred within the last 5 seconds
 	 */
-	if ((hwerrs & ~dd->ipath_lasthwerror) ||
+	if ((hwerrs & ~(dd->ipath_lasthwerror |
+			((INFINIPATH_HWE_TXEMEMPARITYERR_PIOBUF |
+			  INFINIPATH_HWE_TXEMEMPARITYERR_PIOPBC)
+			 << INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT))) ||
 	    (ipath_debug & __IPATH_VERBDBG))
 		dev_info(&dd->pcidev->dev, "Hardware error: hwerr=0x%llx "
 			 "(cleared)\n", (unsigned long long) hwerrs);
 	dd->ipath_lasthwerror |= hwerrs;
 
-	if (hwerrs & ~infinipath_hwe_bitsextant)
+	if (hwerrs & ~dd->ipath_hwe_bitsextant)
 		ipath_dev_err(dd, "hwerror interrupt with unknown errors "
 			      "%llx set\n", (unsigned long long)
-			      (hwerrs & ~infinipath_hwe_bitsextant));
+			      (hwerrs & ~dd->ipath_hwe_bitsextant));
 
 	ctrl = ipath_read_kreg32(dd, dd->ipath_kregs->kr_control);
 	if (ctrl & INFINIPATH_C_FREEZEMODE) {
+		/*
+		 * parity errors in send memory are recoverable,
+		 * just cancel the send (if indicated in * sendbuffererror),
+		 * count the occurrence, unfreeze (if no other handled
+		 * hardware error bits are set), and continue. They can
+		 * occur if a processor speculative read is done to the PIO
+		 * buffer while we are sending a packet, for example.
+		 */
+		if (hwerrs & ((INFINIPATH_HWE_TXEMEMPARITYERR_PIOBUF |
+			       INFINIPATH_HWE_TXEMEMPARITYERR_PIOPBC)
+			      << INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT)) {
+			ipath_stats.sps_txeparity++;
+			ipath_dbg("Recovering from TXE parity error (%llu), "
+			    	  "hwerrstatus=%llx\n",
+				  (unsigned long long) ipath_stats.sps_txeparity,
+				  (unsigned long long) hwerrs);
+			ipath_disarm_senderrbufs(dd);
+			hwerrs &= ~((INFINIPATH_HWE_TXEMEMPARITYERR_PIOBUF |
+				     INFINIPATH_HWE_TXEMEMPARITYERR_PIOPBC)
+				    << INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT);
+			if (!hwerrs) { /* else leave in freeze mode */
+				ipath_write_kreg(dd,
+						 dd->ipath_kregs->kr_control,
+						 dd->ipath_control);
+			    return;
+			}
+		}
 		if (hwerrs) {
 			/*
 			 * if any set that we aren't ignoring only make the
@@ -379,9 +436,8 @@ static void ipath_pe_handle_hwerrors(struct ipath_devdata *dd, char *msg,
 		} else {
 			ipath_dbg("Clearing freezemode on ignored hardware "
 				  "error\n");
-			ctrl &= ~INFINIPATH_C_FREEZEMODE;
 			ipath_write_kreg(dd, dd->ipath_kregs->kr_control,
-					 ctrl);
+			   		 dd->ipath_control);
 		}
 	}
 
@@ -396,24 +452,13 @@ static void ipath_pe_handle_hwerrors(struct ipath_devdata *dd, char *msg,
 		ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrmask,
 				 dd->ipath_hwerrmask);
 	}
-	if (hwerrs & (INFINIPATH_HWE_RXEMEMPARITYERR_MASK
-		      << INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT)) {
-		bits = (u32) ((hwerrs >>
-			       INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT) &
-			      INFINIPATH_HWE_RXEMEMPARITYERR_MASK);
-		snprintf(bitsmsg, sizeof bitsmsg, "[RXE Parity Errs %x] ",
-			 bits);
-		strlcat(msg, bitsmsg, msgl);
-	}
-	if (hwerrs & (INFINIPATH_HWE_TXEMEMPARITYERR_MASK
-		      << INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT)) {
-		bits = (u32) ((hwerrs >>
-			       INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT) &
-			      INFINIPATH_HWE_TXEMEMPARITYERR_MASK);
-		snprintf(bitsmsg, sizeof bitsmsg, "[TXE Parity Errs %x] ",
-			 bits);
-		strlcat(msg, bitsmsg, msgl);
-	}
+
+	ipath_format_hwerrors(hwerrs,
+			      ipath_6120_hwerror_msgs,
+			      sizeof(ipath_6120_hwerror_msgs)/
+			      sizeof(ipath_6120_hwerror_msgs[0]),
+			      msg, msgl);
+
 	if (hwerrs & (INFINIPATH_HWE_PCIEMEMPARITYERR_MASK
 		      << INFINIPATH_HWE_PCIEMEMPARITYERR_SHIFT)) {
 		bits = (u32) ((hwerrs >>
@@ -423,10 +468,6 @@ static void ipath_pe_handle_hwerrors(struct ipath_devdata *dd, char *msg,
 			 "[PCIe Mem Parity Errs %x] ", bits);
 		strlcat(msg, bitsmsg, msgl);
 	}
-	if (hwerrs & INFINIPATH_HWE_IBCBUSTOSPCPARITYERR)
-		strlcat(msg, "[IB2IPATH Parity]", msgl);
-	if (hwerrs & INFINIPATH_HWE_IBCBUSFRSPCPARITYERR)
-		strlcat(msg, "[IPATH2IB Parity]", msgl);
 
 #define _IPATH_PLL_FAIL (INFINIPATH_HWE_COREPLL_FBSLIP |	\
 			 INFINIPATH_HWE_COREPLL_RFSLIP )
@@ -452,34 +493,6 @@ static void ipath_pe_handle_hwerrors(struct ipath_devdata *dd, char *msg,
 				 dd->ipath_hwerrmask);
 	}
 
-	if (hwerrs & INFINIPATH_HWE_PCIEPOISONEDTLP)
-		strlcat(msg, "[PCIe Poisoned TLP]", msgl);
-	if (hwerrs & INFINIPATH_HWE_PCIECPLTIMEOUT)
-		strlcat(msg, "[PCIe completion timeout]", msgl);
-
-	/*
-	 * In practice, it's unlikely wthat we'll see PCIe PLL, or bus
-	 * parity or memory parity error failures, because most likely we
-	 * won't be able to talk to the core of the chip.  Nonetheless, we
-	 * might see them, if they are in parts of the PCIe core that aren't
-	 * essential.
-	 */
-	if (hwerrs & INFINIPATH_HWE_PCIE1PLLFAILED)
-		strlcat(msg, "[PCIePLL1]", msgl);
-	if (hwerrs & INFINIPATH_HWE_PCIE0PLLFAILED)
-		strlcat(msg, "[PCIePLL0]", msgl);
-	if (hwerrs & INFINIPATH_HWE_PCIEBUSPARITYXTLH)
-		strlcat(msg, "[PCIe XTLH core parity]", msgl);
-	if (hwerrs & INFINIPATH_HWE_PCIEBUSPARITYXADM)
-		strlcat(msg, "[PCIe ADM TX core parity]", msgl);
-	if (hwerrs & INFINIPATH_HWE_PCIEBUSPARITYRADM)
-		strlcat(msg, "[PCIe ADM RX core parity]", msgl);
-
-	if (hwerrs & INFINIPATH_HWE_RXDSYNCMEMPARITYERR)
-		strlcat(msg, "[Rx Dsync]", msgl);
-	if (hwerrs & INFINIPATH_HWE_SERDESPLLFAILED)
-		strlcat(msg, "[SerDes PLL]", msgl);
-
 	ipath_dev_err(dd, "%s hardware error\n", msg);
 	if (isfatal && !ipath_diag_inuse && dd->ipath_freezemsg) {
 		/*
@@ -525,6 +538,9 @@ static int ipath_pe_boardname(struct ipath_devdata *dd, char *name,
 	case 5:
 		n = "InfiniPath_QMH7140";
 		break;
+	case 6:
+		n = "InfiniPath_QLE7142";
+		break;
 	default:
 		ipath_dev_err(dd,
 			      "Don't yet know about board with ID %u\n",
@@ -571,9 +587,12 @@ static void ipath_pe_init_hwerrors(struct ipath_devdata *dd)
 	if (!dd->ipath_boardrev)	// no PLL for Emulator
 		val &= ~INFINIPATH_HWE_SERDESPLLFAILED;
 
-	/* workaround bug 9460 in internal interface bus parity checking */
-	val &= ~INFINIPATH_HWE_PCIEBUSPARITYRADM;
-
+	if (dd->ipath_minrev < 2) {
+		/* workaround bug 9460 in internal interface bus parity
+		 * checking. Fixed (HW bug 9490) in Rev2.
+		 */
+		val &= ~INFINIPATH_HWE_PCIEBUSPARITYRADM;
+	}
 	dd->ipath_hwerrmask = val;
 }
 
@@ -583,8 +602,8 @@ static void ipath_pe_init_hwerrors(struct ipath_devdata *dd)
  */
 static int ipath_pe_bringup_serdes(struct ipath_devdata *dd)
 {
-	u64 val, tmp, config1;
-	int ret = 0, change = 0;
+	u64 val, tmp, config1, prev_val;
+	int ret = 0;
 
 	ipath_dbg("Trying to bringup serdes\n");
 
@@ -641,6 +660,7 @@ static int ipath_pe_bringup_serdes(struct ipath_devdata *dd)
 	val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_scratch);
 
 	val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig);
+	prev_val = val;
 	if (((val >> INFINIPATH_XGXS_MDIOADDR_SHIFT) &
 	     INFINIPATH_XGXS_MDIOADDR_MASK) != 3) {
 		val &=
@@ -648,11 +668,9 @@ static int ipath_pe_bringup_serdes(struct ipath_devdata *dd)
 			  INFINIPATH_XGXS_MDIOADDR_SHIFT);
 		/* MDIO address 3 */
 		val |= 3ULL << INFINIPATH_XGXS_MDIOADDR_SHIFT;
-		change = 1;
 	}
 	if (val & INFINIPATH_XGXS_RESET) {
 		val &= ~INFINIPATH_XGXS_RESET;
-		change = 1;
 	}
 	if (((val >> INFINIPATH_XGXS_RX_POL_SHIFT) &
 	     INFINIPATH_XGXS_RX_POL_MASK) != dd->ipath_rx_pol_inv ) {
@@ -661,9 +679,19 @@ static int ipath_pe_bringup_serdes(struct ipath_devdata *dd)
 		         INFINIPATH_XGXS_RX_POL_SHIFT);
 		val |= dd->ipath_rx_pol_inv <<
 			INFINIPATH_XGXS_RX_POL_SHIFT;
-		change = 1;
 	}
-	if (change)
+	if (dd->ipath_minrev >= 2) {
+		/* Rev 2. can tolerate multiple writes to PBC, and
+		 * allowing them can provide lower latency on some
+		 * CPUs, but this feature is off by default, only
+		 * turned on by setting D63 of XGXSconfig reg.
+		 * May want to make this conditional more
+		 * fine-grained in future. This is not exactly
+		 * related to XGXS, but where the bit ended up.
+		 */
+		val |= INFINIPATH_XGXS_SUPPRESS_ARMLAUNCH_ERR;
+	}
+	if (val != prev_val)
 		ipath_write_kreg(dd, dd->ipath_kregs->kr_xgxsconfig, val);
 
 	val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesconfig0);
@@ -717,9 +745,25 @@ static void ipath_pe_quiet_serdes(struct ipath_devdata *dd)
 	ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig0, val);
 }
 
-/* this is not yet needed on this chip, so just return 0. */
 static int ipath_pe_intconfig(struct ipath_devdata *dd)
 {
+	u64 val;
+	u32 chiprev;
+
+	/*
+	 * If the chip supports added error indication via GPIO pins,
+	 * enable interrupts on those bits so the interrupt routine
+	 * can count the events. Also set flag so interrupt routine
+	 * can know they are expected.
+	 */
+	chiprev = dd->ipath_revision >> INFINIPATH_R_CHIPREVMINOR_SHIFT;
+	if ((chiprev & INFINIPATH_R_CHIPREVMINOR_MASK) > 1) {
+		/* Rev2+ reports extra errors via internal GPIO pins */
+		dd->ipath_flags |= IPATH_GPIO_ERRINTRS;
+		val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_gpio_mask);
+		val |= IPATH_GPIO_ERRINTR_MASK;
+		ipath_write_kreg( dd, dd->ipath_kregs->kr_gpio_mask, val);
+	}
 	return 0;
 }
 
@@ -853,21 +897,23 @@ static int ipath_setup_pe_config(struct ipath_devdata *dd,
 	return 0;
 }
 
-static void ipath_init_pe_variables(void)
+static void ipath_init_pe_variables(struct ipath_devdata *dd)
 {
 	/*
 	 * bits for selecting i2c direction and values,
 	 * used for I2C serial flash
 	 */
-	ipath_gpio_sda_num = _IPATH_GPIO_SDA_NUM;
-	ipath_gpio_scl_num = _IPATH_GPIO_SCL_NUM;
-	ipath_gpio_sda = IPATH_GPIO_SDA;
-	ipath_gpio_scl = IPATH_GPIO_SCL;
+	dd->ipath_gpio_sda_num = _IPATH_GPIO_SDA_NUM;
+	dd->ipath_gpio_scl_num = _IPATH_GPIO_SCL_NUM;
+	dd->ipath_gpio_sda = IPATH_GPIO_SDA;
+	dd->ipath_gpio_scl = IPATH_GPIO_SCL;
 
 	/* variables for sanity checking interrupt and errors */
-	infinipath_hwe_bitsextant =
+	dd->ipath_hwe_bitsextant =
 		(INFINIPATH_HWE_RXEMEMPARITYERR_MASK <<
 		 INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT) |
+		(INFINIPATH_HWE_TXEMEMPARITYERR_MASK <<
+		 INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT) |
 		(INFINIPATH_HWE_PCIEMEMPARITYERR_MASK <<
 		 INFINIPATH_HWE_PCIEMEMPARITYERR_SHIFT) |
 		INFINIPATH_HWE_PCIE1PLLFAILED |
@@ -883,13 +929,13 @@ static void ipath_init_pe_variables(void)
 		INFINIPATH_HWE_SERDESPLLFAILED |
 		INFINIPATH_HWE_IBCBUSTOSPCPARITYERR |
 		INFINIPATH_HWE_IBCBUSFRSPCPARITYERR;
-	infinipath_i_bitsextant =
+	dd->ipath_i_bitsextant =
 		(INFINIPATH_I_RCVURG_MASK << INFINIPATH_I_RCVURG_SHIFT) |
 		(INFINIPATH_I_RCVAVAIL_MASK <<
 		 INFINIPATH_I_RCVAVAIL_SHIFT) |
 		INFINIPATH_I_ERROR | INFINIPATH_I_SPIOSENT |
 		INFINIPATH_I_SPIOBUFAVAIL | INFINIPATH_I_GPIO;
-	infinipath_e_bitsextant =
+	dd->ipath_e_bitsextant =
 		INFINIPATH_E_RFORMATERR | INFINIPATH_E_RVCRC |
 		INFINIPATH_E_RICRC | INFINIPATH_E_RMINPKTLEN |
 		INFINIPATH_E_RMAXPKTLEN | INFINIPATH_E_RLONGPKTLEN |
@@ -907,8 +953,8 @@ static void ipath_init_pe_variables(void)
 		INFINIPATH_E_INVALIDADDR | INFINIPATH_E_RESET |
 		INFINIPATH_E_HARDWARE;
 
-	infinipath_i_rcvavail_mask = INFINIPATH_I_RCVAVAIL_MASK;
-	infinipath_i_rcvurg_mask = INFINIPATH_I_RCVURG_MASK;
+	dd->ipath_i_rcvavail_mask = INFINIPATH_I_RCVAVAIL_MASK;
+	dd->ipath_i_rcvurg_mask = INFINIPATH_I_RCVURG_MASK;
 }
 
 /* setup the MSI stuff again after a reset.  I'd like to just call
@@ -1082,6 +1128,45 @@ static void ipath_pe_put_tid(struct ipath_devdata *dd, u64 __iomem *tidptr,
 	mmiowb();
 	spin_unlock_irqrestore(&dd->ipath_tid_lock, flags);
 }
+/**
+ * ipath_pe_put_tid_2 - write a TID in chip, Revision 2 or higher
+ * @dd: the infinipath device
+ * @tidptr: pointer to the expected TID (in chip) to udpate
+ * @tidtype: 0 for eager, 1 for expected
+ * @pa: physical address of in memory buffer; ipath_tidinvalid if freeing
+ *
+ * This exists as a separate routine to allow for selection of the
+ * appropriate "flavor". The static calls in cleanup just use the
+ * revision-agnostic form, as they are not performance critical.
+ */
+static void ipath_pe_put_tid_2(struct ipath_devdata *dd, u64 __iomem *tidptr,
+			     u32 type, unsigned long pa)
+{
+	u32 __iomem *tidp32 = (u32 __iomem *)tidptr;
+
+	if (pa != dd->ipath_tidinvalid) {
+		if (pa & ((1U << 11) - 1)) {
+			dev_info(&dd->pcidev->dev, "BUG: physaddr %lx "
+				 "not 2KB aligned!\n", pa);
+			return;
+		}
+		pa >>= 11;
+		/* paranoia check */
+		if (pa & (7<<29))
+			ipath_dev_err(dd,
+				      "BUG: Physical page address 0x%lx "
+				      "has bits set in 31-29\n", pa);
+
+		if (type == 0)
+			pa |= dd->ipath_tidtemplate;
+		else /* for now, always full 4KB page */
+			pa |= 2 << 29;
+	}
+	if (dd->ipath_kregbase)
+		writel(pa, tidp32);
+	mmiowb();
+}
+
 
 /**
  * ipath_pe_clear_tid - clear all TID entries for a port, expected and eager
@@ -1203,7 +1288,7 @@ int __attribute__((weak)) ipath_unordered_wc(void)
 
 /**
  * ipath_init_pe_get_base_info - set chip-specific flags for user code
- * @dd: the infinipath device
+ * @pd: the infinipath port
  * @kbase: ipath_base_info pointer
  *
  * We set the PCIE flag because the lower bandwidth on PCIe vs
@@ -1212,6 +1297,7 @@ int __attribute__((weak)) ipath_unordered_wc(void)
 static int ipath_pe_get_base_info(struct ipath_portdata *pd, void *kbase)
 {
 	struct ipath_base_info *kinfo = kbase;
+	struct ipath_devdata *dd;
 
 	if (ipath_unordered_wc()) {
 		kinfo->spi_runtime_flags |= IPATH_RUNTIME_FORCE_WC_ORDER;
@@ -1220,8 +1306,20 @@ static int ipath_pe_get_base_info(struct ipath_portdata *pd, void *kbase)
 	else
 		ipath_cdbg(PROC, "Not Intel processor, WC ordered\n");
 
-	kinfo->spi_runtime_flags |= IPATH_RUNTIME_PCIE;
+	if (pd == NULL)
+		goto done;
 
+	dd = pd->port_dd;
+
+	if (dd != NULL && dd->ipath_minrev >= 2) {
+		ipath_cdbg(PROC, "IBA6120 Rev2, allow multiple PBC write\n");
+		kinfo->spi_runtime_flags |= IPATH_RUNTIME_PBC_REWRITE;
+		ipath_cdbg(PROC, "IBA6120 Rev2, allow loose DMA alignment\n");
+		kinfo->spi_runtime_flags |= IPATH_RUNTIME_LOOSE_DMA_ALIGN;
+	}
+
+done:
+	kinfo->spi_runtime_flags |= IPATH_RUNTIME_PCIE;
 	return 0;
 }
 
@@ -1244,7 +1342,10 @@ void ipath_init_iba6120_funcs(struct ipath_devdata *dd)
 	dd->ipath_f_quiet_serdes = ipath_pe_quiet_serdes;
 	dd->ipath_f_bringup_serdes = ipath_pe_bringup_serdes;
 	dd->ipath_f_clear_tids = ipath_pe_clear_tids;
-	dd->ipath_f_put_tid = ipath_pe_put_tid;
+	if (dd->ipath_minrev >= 2)
+		dd->ipath_f_put_tid = ipath_pe_put_tid_2;
+	else
+		dd->ipath_f_put_tid = ipath_pe_put_tid;
 	dd->ipath_f_cleanup = ipath_setup_pe_cleanup;
 	dd->ipath_f_setextled = ipath_setup_pe_setextled;
 	dd->ipath_f_get_base_info = ipath_pe_get_base_info;
@@ -1259,6 +1360,6 @@ void ipath_init_iba6120_funcs(struct ipath_devdata *dd)
 	dd->ipath_kregs = &ipath_pe_kregs;
 	dd->ipath_cregs = &ipath_pe_cregs;
 
-	ipath_init_pe_variables();
+	ipath_init_pe_variables(dd);
 }