diff options
Diffstat (limited to 'drivers/ide')
| -rw-r--r-- | drivers/ide/Kconfig | 6 | ||||
| -rw-r--r-- | drivers/ide/pci/Makefile | 1 | ||||
| -rw-r--r-- | drivers/ide/pci/it821x.c | 812 |
3 files changed, 819 insertions, 0 deletions
diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig index 0273f124a4f..5f33df47aa7 100644 --- a/drivers/ide/Kconfig +++ b/drivers/ide/Kconfig @@ -606,6 +606,12 @@ config BLK_DEV_IT8172 <http://www.ite.com.tw/ia/brief_it8172bsp.htm>; picture of the board at <http://www.mvista.com/partners/semiconductor/ite.html>. +config BLK_DEV_IT821X + tristate "IT821X IDE support" + help + This driver adds support for the ITE 8211 IDE controller and the + IT 8212 IDE RAID controller in both RAID and pass-through mode. + config BLK_DEV_NS87415 tristate "NS87415 chipset support" help diff --git a/drivers/ide/pci/Makefile b/drivers/ide/pci/Makefile index 55e6e553e49..af46226c179 100644 --- a/drivers/ide/pci/Makefile +++ b/drivers/ide/pci/Makefile @@ -12,6 +12,7 @@ obj-$(CONFIG_BLK_DEV_HPT34X) += hpt34x.o obj-$(CONFIG_BLK_DEV_HPT366) += hpt366.o #obj-$(CONFIG_BLK_DEV_HPT37X) += hpt37x.o obj-$(CONFIG_BLK_DEV_IT8172) += it8172.o +obj-$(CONFIG_BLK_DEV_IT821X) += it821x.o obj-$(CONFIG_BLK_DEV_NS87415) += ns87415.o obj-$(CONFIG_BLK_DEV_OPTI621) += opti621.o obj-$(CONFIG_BLK_DEV_PDC202XX_OLD) += pdc202xx_old.o diff --git a/drivers/ide/pci/it821x.c b/drivers/ide/pci/it821x.c new file mode 100644 index 00000000000..e440036e651 --- /dev/null +++ b/drivers/ide/pci/it821x.c @@ -0,0 +1,812 @@ + +/* + * linux/drivers/ide/pci/it821x.c Version 0.09 December 2004 + * + * Copyright (C) 2004 Red Hat <alan@redhat.com> + * + * May be copied or modified under the terms of the GNU General Public License + * Based in part on the ITE vendor provided SCSI driver. + * + * Documentation available from + * http://www.ite.com.tw/pc/IT8212F_V04.pdf + * Some other documents are NDA. + * + * The ITE8212 isn't exactly a standard IDE controller. It has two + * modes. In pass through mode then it is an IDE controller. In its smart + * mode its actually quite a capable hardware raid controller disguised + * as an IDE controller. Smart mode only understands DMA read/write and + * identify, none of the fancier commands apply. The IT8211 is identical + * in other respects but lacks the raid mode. + * + * Errata: + * o Rev 0x10 also requires master/slave hold the same DMA timings and + * cannot do ATAPI MWDMA. + * o The identify data for raid volumes lacks CHS info (technically ok) + * but also fails to set the LBA28 and other bits. We fix these in + * the IDE probe quirk code. + * o If you write LBA48 sized I/O's (ie > 256 sector) in smart mode + * raid then the controller firmware dies + * o Smart mode without RAID doesn't clear all the necessary identify + * bits to reduce the command set to the one used + * + * This has a few impacts on the driver + * - In pass through mode we do all the work you would expect + * - In smart mode the clocking set up is done by the controller generally + * but we must watch the other limits and filter. + * - There are a few extra vendor commands that actually talk to the + * controller but only work PIO with no IRQ. + * + * Vendor areas of the identify block in smart mode are used for the + * timing and policy set up. Each HDD in raid mode also has a serial + * block on the disk. The hardware extra commands are get/set chip status, + * rebuild, get rebuild status. + * + * In Linux the driver supports pass through mode as if the device was + * just another IDE controller. If the smart mode is running then + * volumes are managed by the controller firmware and each IDE "disk" + * is a raid volume. Even more cute - the controller can do automated + * hotplug and rebuild. + * + * The pass through controller itself is a little demented. It has a + * flaw that it has a single set of PIO/MWDMA timings per channel so + * non UDMA devices restrict each others performance. It also has a + * single clock source per channel so mixed UDMA100/133 performance + * isn't perfect and we have to pick a clock. Thankfully none of this + * matters in smart mode. ATAPI DMA is not currently supported. + * + * It seems the smart mode is a win for RAID1/RAID10 but otherwise not. + * + * TODO + * - ATAPI UDMA is ok but not MWDMA it seems + * - RAID configuration ioctls + * - Move to libata once it grows up + */ + +#include <linux/config.h> +#include <linux/types.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/delay.h> +#include <linux/hdreg.h> +#include <linux/ide.h> +#include <linux/init.h> + +#include <asm/io.h> + +struct it821x_dev +{ + unsigned int smart:1, /* Are we in smart raid mode */ + timing10:1; /* Rev 0x10 */ + u8 clock_mode; /* 0, ATA_50 or ATA_66 */ + u8 want[2][2]; /* Mode/Pri log for master slave */ + /* We need these for switching the clock when DMA goes on/off + The high byte is the 66Mhz timing */ + u16 pio[2]; /* Cached PIO values */ + u16 mwdma[2]; /* Cached MWDMA values */ + u16 udma[2]; /* Cached UDMA values (per drive) */ +}; + +#define ATA_66 0 +#define ATA_50 1 +#define ATA_ANY 2 + +#define UDMA_OFF 0 +#define MWDMA_OFF 0 + +/* + * We allow users to force the card into non raid mode without + * flashing the alternative BIOS. This is also neccessary right now + * for embedded platforms that cannot run a PC BIOS but are using this + * device. + */ + +static int it8212_noraid; + +/** + * it821x_program - program the PIO/MWDMA registers + * @drive: drive to tune + * + * Program the PIO/MWDMA timing for this channel according to the + * current clock. + */ + +static void it821x_program(ide_drive_t *drive, u16 timing) +{ + ide_hwif_t *hwif = drive->hwif; + struct it821x_dev *itdev = ide_get_hwifdata(hwif); + int channel = hwif->channel; + u8 conf; + + /* Program PIO/MWDMA timing bits */ + if(itdev->clock_mode == ATA_66) + conf = timing >> 8; + else + conf = timing & 0xFF; + pci_write_config_byte(hwif->pci_dev, 0x54 + 4 * channel, conf); +} + +/** + * it821x_program_udma - program the UDMA registers + * @drive: drive to tune + * + * Program the UDMA timing for this drive according to the + * current clock. + */ + +static void it821x_program_udma(ide_drive_t *drive, u16 timing) +{ + ide_hwif_t *hwif = drive->hwif; + struct it821x_dev *itdev = ide_get_hwifdata(hwif); + int channel = hwif->channel; + int unit = drive->select.b.unit; + u8 conf; + + /* Program UDMA timing bits */ + if(itdev->clock_mode == ATA_66) + conf = timing >> 8; + else + conf = timing & 0xFF; + if(itdev->timing10 == 0) + pci_write_config_byte(hwif->pci_dev, 0x56 + 4 * channel + unit, conf); + else { + pci_write_config_byte(hwif->pci_dev, 0x56 + 4 * channel, conf); + pci_write_config_byte(hwif->pci_dev, 0x56 + 4 * channel + 1, conf); + } +} + + +/** + * it821x_clock_strategy + * @hwif: hardware interface + * + * Select between the 50 and 66Mhz base clocks to get the best + * results for this interface. + */ + +static void it821x_clock_strategy(ide_drive_t *drive) +{ + ide_hwif_t *hwif = drive->hwif; + struct it821x_dev *itdev = ide_get_hwifdata(hwif); + + u8 unit = drive->select.b.unit; + ide_drive_t *pair = &hwif->drives[1-unit]; + + int clock, altclock; + u8 v; + int sel = 0; + + if(itdev->want[0][0] > itdev->want[1][0]) { + clock = itdev->want[0][1]; + altclock = itdev->want[1][1]; + } else { + clock = itdev->want[1][1]; + altclock = itdev->want[0][1]; + } + + /* Master doesn't care does the slave ? */ + if(clock == ATA_ANY) + clock = altclock; + + /* Nobody cares - keep the same clock */ + if(clock == ATA_ANY) + return; + /* No change */ + if(clock == itdev->clock_mode) + return; + + /* Load this into the controller ? */ + if(clock == ATA_66) + itdev->clock_mode = ATA_66; + else { + itdev->clock_mode = ATA_50; + sel = 1; + } + pci_read_config_byte(hwif->pci_dev, 0x50, &v); + v &= ~(1 << (1 + hwif->channel)); + v |= sel << (1 + hwif->channel); + pci_write_config_byte(hwif->pci_dev, 0x50, v); + + /* + * Reprogram the UDMA/PIO of the pair drive for the switch + * MWDMA will be dealt with by the dma switcher + */ + if(pair && itdev->udma[1-unit] != UDMA_OFF) { + it821x_program_udma(pair, itdev->udma[1-unit]); + it821x_program(pair, itdev->pio[1-unit]); + } + /* + * Reprogram the UDMA/PIO of our drive for the switch. + * MWDMA will be dealt with by the dma switcher + */ + if(itdev->udma[unit] != UDMA_OFF) { + it821x_program_udma(drive, itdev->udma[unit]); + it821x_program(drive, itdev->pio[unit]); + } +} + +/** + * it821x_ratemask - Compute available modes + * @drive: IDE drive + * + * Compute the available speeds for the devices on the interface. This + * is all modes to ATA133 clipped by drive cable setup. + */ + +static u8 it821x_ratemask (ide_drive_t *drive) +{ + u8 mode = 4; + if (!eighty_ninty_three(drive)) + mode = min(mode, (u8)1); + return mode; +} + +/** + * it821x_tuneproc - tune a drive + * @drive: drive to tune + * @mode_wanted: the target operating mode + * + * Load the timing settings for this device mode into the + * controller. By the time we are called the mode has been + * modified as neccessary to handle the absence of seperate + * master/slave timers for MWDMA/PIO. + * + * This code is only used in pass through mode. + */ + +static void it821x_tuneproc (ide_drive_t *drive, byte mode_wanted) +{ + ide_hwif_t *hwif = drive->hwif; + struct it821x_dev *itdev = ide_get_hwifdata(hwif); + int unit = drive->select.b.unit; + + /* Spec says 89 ref driver uses 88 */ + static u16 pio[] = { 0xAA88, 0xA382, 0xA181, 0x3332, 0x3121 }; + static u8 pio_want[] = { ATA_66, ATA_66, ATA_66, ATA_66, ATA_ANY }; + + if(itdev->smart) + return; + + /* We prefer 66Mhz clock for PIO 0-3, don't care for PIO4 */ + itdev->want[unit][1] = pio_want[mode_wanted]; + itdev->want[unit][0] = 1; /* PIO is lowest priority */ + itdev->pio[unit] = pio[mode_wanted]; + it821x_clock_strategy(drive); + it821x_program(drive, itdev->pio[unit]); +} + +/** + * it821x_tune_mwdma - tune a channel for MWDMA + * @drive: drive to set up + * @mode_wanted: the target operating mode + * + * Load the timing settings for this device mode into the + * controller when doing MWDMA in pass through mode. The caller + * must manage the whole lack of per device MWDMA/PIO timings and + * the shared MWDMA/PIO timing register. + */ + +static void it821x_tune_mwdma (ide_drive_t *drive, byte mode_wanted) +{ + ide_hwif_t *hwif = drive->hwif; + struct it821x_dev *itdev = (void *)ide_get_hwifdata(hwif); + int unit = drive->select.b.unit; + int channel = hwif->channel; + u8 conf; + + static u16 dma[] = { 0x8866, 0x3222, 0x3121 }; + static u8 mwdma_want[] = { ATA_ANY, ATA_66, ATA_ANY }; + + itdev->want[unit][1] = mwdma_want[mode_wanted]; + itdev->want[unit][0] = 2; /* MWDMA is low priority */ + itdev->mwdma[unit] = dma[mode_wanted]; + itdev->udma[unit] = UDMA_OFF; + + /* UDMA bits off - Revision 0x10 do them in pairs */ + pci_read_config_byte(hwif->pci_dev, 0x50, &conf); + if(itdev->timing10) + conf |= channel ? 0x60: 0x18; + else + conf |= 1 << (3 + 2 * channel + unit); + pci_write_config_byte(hwif->pci_dev, 0x50, conf); + + it821x_clock_strategy(drive); + /* FIXME: do we need to program this ? */ + /* it821x_program(drive, itdev->mwdma[unit]); */ +} + +/** + * it821x_tune_udma - tune a channel for UDMA + * @drive: drive to set up + * @mode_wanted: the target operating mode + * + * Load the timing settings for this device mode into the + * controller when doing UDMA modes in pass through. + */ + +static void it821x_tune_udma (ide_drive_t *drive, byte mode_wanted) +{ + ide_hwif_t *hwif = drive->hwif; + struct it821x_dev *itdev = ide_get_hwifdata(hwif); + int unit = drive->select.b.unit; + int channel = hwif->channel; + u8 conf; + + static u16 udma[] = { 0x4433, 0x4231, 0x3121, 0x2121, 0x1111, 0x2211, 0x1111 }; + static u8 udma_want[] = { ATA_ANY, ATA_50, ATA_ANY, ATA_66, ATA_66, ATA_50, ATA_66 }; + + itdev->want[unit][1] = udma_want[mode_wanted]; + itdev->want[unit][0] = 3; /* UDMA is high priority */ + itdev->mwdma[unit] = MWDMA_OFF; + itdev->udma[unit] = udma[mode_wanted]; + if(mode_wanted >= 5) + itdev->udma[unit] |= 0x8080; /* UDMA 5/6 select on */ + + /* UDMA on. Again revision 0x10 must do the pair */ + pci_read_config_byte(hwif->pci_dev, 0x50, &conf); + if(itdev->timing10) + conf &= channel ? 0x9F: 0xE7; + else + conf &= ~ (1 << (3 + 2 * channel + unit)); + pci_write_config_byte(hwif->pci_dev, 0x50, conf); + + it821x_clock_strategy(drive); + it821x_program_udma(drive, itdev->udma[unit]); + +} + +/** + * config_it821x_chipset_for_pio - set drive timings + * @drive: drive to tune + * @speed we want + * + * Compute the best pio mode we can for a given device. We must + * pick a speed that does not cause problems with the other device + * on the cable. + */ + +static void config_it821x_chipset_for_pio (ide_drive_t *drive, byte set_speed) +{ + u8 unit = drive->select.b.unit; + ide_hwif_t *hwif = drive->hwif; + ide_drive_t *pair = &hwif->drives[1-unit]; + u8 speed = 0, set_pio = ide_get_best_pio_mode(drive, 255, 5, NULL); + u8 pair_pio; + + /* We have to deal with this mess in pairs */ + if(pair != NULL) { + pair_pio = ide_get_best_pio_mode(pair, 255, 5, NULL); + /* Trim PIO to the slowest of the master/slave */ + if(pair_pio < set_pio) + set_pio = pair_pio; + } + it821x_tuneproc(drive, set_pio); + speed = XFER_PIO_0 + set_pio; + /* XXX - We trim to the lowest of the pair so the other drive + will always be fine at this point until we do hotplug passthru */ + + if (set_speed) + (void) ide_config_drive_speed(drive, speed); +} + +/** + * it821x_dma_read - DMA hook + * @drive: drive for DMA + * + * The IT821x has a single timing register for MWDMA and for PIO + * operations. As we flip back and forth we have to reload the + * clock. In addition the rev 0x10 device only works if the same + * timing value is loaded into the master and slave UDMA clock + * so we must also reload that. + * + * FIXME: we could figure out in advance if we need to do reloads + */ + +static void it821x_dma_start(ide_drive_t *drive) +{ + ide_hwif_t *hwif = drive->hwif; + struct it821x_dev *itdev = ide_get_hwifdata(hwif); + int unit = drive->select.b.unit; + if(itdev->mwdma[unit] != MWDMA_OFF) + it821x_program(drive, itdev->mwdma[unit]); + else if(itdev->udma[unit] != UDMA_OFF && itdev->timing10) + it821x_program_udma(drive, itdev->udma[unit]); + ide_dma_start(drive); +} + +/** + * it821x_dma_write - DMA hook + * @drive: drive for DMA stop + * + * The IT821x has a single timing register for MWDMA and for PIO + * operations. As we flip back and forth we have to reload the + * clock. + */ + +static int it821x_dma_end(ide_drive_t *drive) +{ + ide_hwif_t *hwif = drive->hwif; + int unit = drive->select.b.unit; + struct it821x_dev *itdev = ide_get_hwifdata(hwif); + int ret = __ide_dma_end(drive); + if(itdev->mwdma[unit] != MWDMA_OFF) + it821x_program(drive, itdev->pio[unit]); + return ret; +} + + +/** + * it821x_tune_chipset - set controller timings + * @drive: Drive to set up + * @xferspeed: speed we want to achieve + * + * Tune the ITE chipset for the desired mode. If we can't achieve + * the desired mode then tune for a lower one, but ultimately + * make the thing work. + */ + +static int it821x_tune_chipset (ide_drive_t *drive, byte xferspeed) +{ + + ide_hwif_t *hwif = drive->hwif; + struct it821x_dev *itdev = ide_get_hwifdata(hwif); + u8 speed = ide_rate_filter(it821x_ratemask(drive), xferspeed); + + if(!itdev->smart) { + switch(speed) { + case XFER_PIO_4: + case XFER_PIO_3: + case XFER_PIO_2: + case XFER_PIO_1: + case XFER_PIO_0: + it821x_tuneproc(drive, (speed - XFER_PIO_0)); + break; + /* MWDMA tuning is really hard because our MWDMA and PIO + timings are kept in the same place. We can switch in the + host dma on/off callbacks */ + case XFER_MW_DMA_2: + case XFER_MW_DMA_1: + case XFER_MW_DMA_0: + it821x_tune_mwdma(drive, (speed - XFER_MW_DMA_0)); + break; + case XFER_UDMA_6: + case XFER_UDMA_5: + case XFER_UDMA_4: + case XFER_UDMA_3: + case XFER_UDMA_2: + case XFER_UDMA_1: + case XFER_UDMA_0: + it821x_tune_udma(drive, (speed - XFER_UDMA_0)); + break; + default: + return 1; + } + } + /* + * In smart mode the clocking is done by the host controller + * snooping the mode we picked. The rest of it is not our problem + */ + return ide_config_drive_speed(drive, speed); +} + +/** + * config_chipset_for_dma - configure for DMA + * @drive: drive to configure + * + * Called by the IDE layer when it wants the timings set up. + */ + +static int config_chipset_for_dma (ide_drive_t *drive) +{ + u8 speed = ide_dma_speed(drive, it821x_ratemask(drive)); + + config_it821x_chipset_for_pio(drive, !speed); + it821x_tune_chipset(drive, speed); + return ide_dma_enable(drive); +} + +/** + * it821x_configure_drive_for_dma - set up for DMA transfers + * @drive: drive we are going to set up + * + * Set up the drive for DMA, tune the controller and drive as + * required. If the drive isn't suitable for DMA or we hit + * other problems then we will drop down to PIO and set up + * PIO appropriately + */ + +static int it821x_config_drive_for_dma (ide_drive_t *drive) +{ + ide_hwif_t *hwif = drive->hwif; + + if (ide_use_dma(drive)) { + if (config_chipset_for_dma(drive)) + return hwif->ide_dma_on(drive); + } + config_it821x_chipset_for_pio(drive, 1); + return hwif->ide_dma_off_quietly(drive); +} + +/** + * ata66_it821x - check for 80 pin cable + * @hwif: interface to check + * + * Check for the presence of an ATA66 capable cable on the + * interface. Problematic as it seems some cards don't have + * the needed logic onboard. + */ + +static unsigned int __devinit ata66_it821x(ide_hwif_t *hwif) +{ + /* The reference driver also only does disk side */ + return 1; +} + +/** + * it821x_fixup - post init callback + * @hwif: interface + * + * This callback is run after the drives have been probed but + * before anything gets attached. It allows drivers to do any + * final tuning that is needed, or fixups to work around bugs. + */ + +static void __devinit it821x_fixups(ide_hwif_t *hwif) +{ + struct it821x_dev *itdev = ide_get_hwifdata(hwif); + int i; + + if(!itdev->smart) { + /* + * If we are in pass through mode then not much + * needs to be done, but we do bother to clear the + * IRQ mask as we may well be in PIO (eg rev 0x10) + * for now and we know unmasking is safe on this chipset. + */ + for (i = 0; i < 2; i++) { + ide_drive_t *drive = &hwif->drives[i]; + if(drive->present) + drive->unmask = 1; + } + return; + } + /* + * Perform fixups on smart mode. We need to "lose" some + * capabilities the firmware lacks but does not filter, and + * also patch up some capability bits that it forgets to set + * in RAID mode. + */ + + for(i = 0; i < 2; i++) { + ide_drive_t *drive = &hwif->drives[i]; + struct hd_driveid *id; + u16 *idbits; + + if(!drive->present) + continue; + id = drive->id; + idbits = (u16 *)drive->id; + + /* Check for RAID v native */ + if(strstr(id->model, "Integrated Technology Express")) { + /* In raid mode the ident block is slightly buggy + We need to set the bits so that the IDE layer knows + LBA28. LBA48 and DMA ar valid */ + id->capability |= 3; /* LBA28, DMA */ + id->command_set_2 |= 0x0400; /* LBA48 valid */ + id->cfs_enable_2 |= 0x0400; /* LBA48 on */ + /* Reporting logic */ + printk(KERN_INFO "%s: IT8212 %sRAID %d volume", + drive->name, + idbits[147] ? "Bootable ":"", + idbits[129]); + if(idbits[129] != 1) + printk("(%dK stripe)", idbits[146]); + printk(".\n"); + /* Now the core code will have wrongly decided no DMA + so we need to fix this */ + hwif->ide_dma_off_quietly(drive); +#ifdef CONFIG_IDEDMA_ONLYDISK + if (drive->media == ide_disk) +#endif + hwif->ide_dma_check(drive); + } else { + /* Non RAID volume. Fixups to stop the core code + doing unsupported things */ + id->field_valid &= 1; + id->queue_depth = 0; + id->command_set_1 = 0; + id->command_set_2 &= 0xC400; + id->cfsse &= 0xC000; + id->cfs_enable_1 = 0; + id->cfs_enable_2 &= 0xC400; + id->csf_default &= 0xC000; + id->word127 = 0; + id->dlf = 0; + id->csfo = 0; + id->cfa_power = 0; + printk(KERN_INFO "%s: Performing identify fixups.\n", + drive->name); + } + } + +} + +/** + * init_hwif_it821x - set up hwif structs + * @hwif: interface to set up + * + * We do the basic set up of the interface structure. The IT8212 + * requires several custom handlers so we override the default + * ide DMA handlers appropriately + */ + +static void __devinit init_hwif_it821x(ide_hwif_t *hwif) +{ + struct it821x_dev *idev = kmalloc(sizeof(struct it821x_dev), GFP_KERNEL); + u8 conf; + + if(idev == NULL) { + printk(KERN_ERR "it821x: out of memory, falling back to legacy behaviour.\n"); + goto fallback; + } + memset(idev, 0, sizeof(struct it821x_dev)); + ide_set_hwifdata(hwif, idev); + + pci_read_config_byte(hwif->pci_dev, 0x50, &conf); + if(conf & 1) { + idev->smart = 1; + hwif->atapi_dma = 0; + /* Long I/O's although allowed in LBA48 space cause the + onboard firmware to enter the twighlight zone */ + hwif->rqsize = 256; + } + + /* Pull the current clocks from 0x50 also */ + if (conf & (1 << (1 + hwif->channel))) + idev->clock_mode = ATA_50; + else + idev->clock_mode = ATA_66; + + idev->want[0][1] = ATA_ANY; + idev->want[1][1] = ATA_ANY; + + /* + * Not in the docs but according to the reference driver + * this is neccessary. + */ + + pci_read_config_byte(hwif->pci_dev, 0x08, &conf); + if(conf == 0x10) { + idev->timing10 = 1; + hwif->atapi_dma = 0; + if(!idev->smart) + printk(KERN_WARNING "it821x: Revision 0x10, workarounds activated.\n"); + } + + hwif->speedproc = &it821x_tune_chipset; + hwif->tuneproc = &it821x_tuneproc; + + /* MWDMA/PIO clock switching for pass through mode */ + if(!idev->smart) { + hwif->dma_start = &it821x_dma_start; + hwif->ide_dma_end = &it821x_dma_end; + } + + hwif->drives[0].autotune = 1; + hwif->drives[1].autotune = 1; + + if (!hwif->dma_base) + goto fallback; + + hwif->ultra_mask = 0x7f; + hwif->mwdma_mask = 0x07; + hwif->swdma_mask = 0x07; + + hwif->ide_dma_check = &it821x_config_drive_for_dma; + if (!(hwif->udma_four)) + hwif->udma_four = ata66_it821x(hwif); + + /* + * The BIOS often doesn't set up DMA on this controller + * so we always do it. + */ + + hwif->autodma = 1; + hwif->drives[0].autodma = hwif->autodma; + hwif->drives[1].autodma = hwif->autodma; + return; +fallback: + hwif->autodma = 0; + return; +} + +static void __devinit it8212_disable_raid(struct pci_dev *dev) +{ + /* Reset local CPU, and set BIOS not ready */ + pci_write_config_byte(dev, 0x5E, 0x01); + + /* Set to bypass mode, and reset PCI bus */ + pci_write_config_byte(dev, 0x50, 0x00); + pci_write_config_word(dev, PCI_COMMAND, + PCI_COMMAND_PARITY | PCI_COMMAND_IO | + PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER); + pci_write_config_word(dev, 0x40, 0xA0F3); + + pci_write_config_dword(dev,0x4C, 0x02040204); + pci_write_config_byte(dev, 0x42, 0x36); + pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0); +} + +static unsigned int __devinit init_chipset_it821x(struct pci_dev *dev, const char *name) +{ + u8 conf; + static char *mode[2] = { "pass through", "smart" }; + + /* Force the card into bypass mode if so requested */ + if (it8212_noraid) { + printk(KERN_INFO "it8212: forcing bypass mode.\n"); + it8212_disable_raid(dev); + } + pci_read_config_byte(dev, 0x50, &conf); + printk(KERN_INFO "it821x: controller in %s mode.\n", mode[conf & 1]); + return 0; +} + + +#define DECLARE_ITE_DEV(name_str) \ + { \ + .name = name_str, \ + .init_chipset = init_chipset_it821x, \ + .init_hwif = init_hwif_it821x, \ + .channels = 2, \ + .autodma = AUTODMA, \ + .bootable = ON_BOARD, \ + .fixup = it821x_fixups \ + } + +static ide_pci_device_t it821x_chipsets[] __devinitdata = { + /* 0 */ DECLARE_ITE_DEV("IT8212"), +}; + +/** + * it821x_init_one - pci layer discovery entry + * @dev: PCI device + * @id: ident table entry + * + * Called by the PCI code when it finds an ITE821x controller. + * We then use the IDE PCI generic helper to do most of the work. + */ + +static int __devinit it821x_init_one(struct pci_dev *dev, const struct pci_device_id *id) +{ + ide_setup_pci_device(dev, &it821x_chipsets[id->driver_data]); + return 0; +} + +static struct pci_device_id it821x_pci_tbl[] = { + { PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_8211, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, + { PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_8212, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, + { 0, }, +}; + +MODULE_DEVICE_TABLE(pci, it821x_pci_tbl); + +static struct pci_driver driver = { + .name = "ITE821x IDE", + .id_table = it821x_pci_tbl, + .probe = it821x_init_one, +}; + +static int __init it821x_ide_init(void) +{ + return ide_pci_register_driver(&driver); +} + +module_init(it821x_ide_init); + +module_param_named(noraid, it8212_noraid, int, S_IRUGO); +MODULE_PARM_DESC(it8212_noraid, "Force card into bypass mode"); + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("PCI driver module for the ITE 821x"); +MODULE_LICENSE("GPL"); |