aboutsummaryrefslogtreecommitdiff
path: root/drivers/ide/pci/opti621.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/ide/pci/opti621.c')
-rw-r--r--drivers/ide/pci/opti621.c247
1 files changed, 0 insertions, 247 deletions
diff --git a/drivers/ide/pci/opti621.c b/drivers/ide/pci/opti621.c
deleted file mode 100644
index 6048eda3cd6..00000000000
--- a/drivers/ide/pci/opti621.c
+++ /dev/null
@@ -1,247 +0,0 @@
-/*
- * Copyright (C) 1996-1998 Linus Torvalds & authors (see below)
- */
-
-/*
- * Authors:
- * Jaromir Koutek <miri@punknet.cz>,
- * Jan Harkes <jaharkes@cwi.nl>,
- * Mark Lord <mlord@pobox.com>
- * Some parts of code are from ali14xx.c and from rz1000.c.
- *
- * OPTi is trademark of OPTi, Octek is trademark of Octek.
- *
- * I used docs from OPTi databook, from ftp.opti.com, file 9123-0002.ps
- * and disassembled/traced setupvic.exe (DOS program).
- * It increases kernel code about 2 kB.
- * I don't have this card no more, but I hope I can get some in case
- * of needed development.
- * My card is Octek PIDE 1.01 (on card) or OPTiViC (program).
- * It has a place for a secondary connector in circuit, but nothing
- * is there. Also BIOS says no address for
- * secondary controller (see bellow in ide_init_opti621).
- * I've only tested this on my system, which only has one disk.
- * It's Western Digital WDAC2850, with PIO mode 3. The PCI bus
- * is at 20 MHz (I have DX2/80, I tried PCI at 40, but I got random
- * lockups). I tried the OCTEK double speed CD-ROM and
- * it does not work! But I can't boot DOS also, so it's probably
- * hardware fault. I have connected Conner 80MB, the Seagate 850MB (no
- * problems) and Seagate 1GB (as slave, WD as master). My experiences
- * with the third, 1GB drive: I got 3MB/s (hdparm), but sometimes
- * it slows to about 100kB/s! I don't know why and I have
- * not this drive now, so I can't try it again.
- * I write this driver because I lost the paper ("manual") with
- * settings of jumpers on the card and I have to boot Linux with
- * Loadlin except LILO, cause I have to run the setupvic.exe program
- * already or I get disk errors (my test: rpm -Vf
- * /usr/X11R6/bin/XF86_SVGA - or any big file).
- * Some numbers from hdparm -t /dev/hda:
- * Timing buffer-cache reads: 32 MB in 3.02 seconds =10.60 MB/sec
- * Timing buffered disk reads: 16 MB in 5.52 seconds = 2.90 MB/sec
- * I have 4 Megs/s before, but I don't know why (maybe changes
- * in hdparm test).
- * After release of 0.1, I got some successful reports, so it might work.
- *
- * The main problem with OPTi is that some timings for master
- * and slave must be the same. For example, if you have master
- * PIO 3 and slave PIO 0, driver have to set some timings of
- * master for PIO 0. Second problem is that opti621_set_pio_mode
- * got only one drive to set, but have to set both drives.
- * This is solved in compute_pios. If you don't set
- * the second drive, compute_pios use ide_get_best_pio_mode
- * for autoselect mode (you can change it to PIO 0, if you want).
- * If you then set the second drive to another PIO, the old value
- * (automatically selected) will be overrided by yours.
- * There is a 25/33MHz switch in configuration
- * register, but driver is written for use at any frequency.
- *
- * Version 0.1, Nov 8, 1996
- * by Jaromir Koutek, for 2.1.8.
- * Initial version of driver.
- *
- * Version 0.2
- * Number 0.2 skipped.
- *
- * Version 0.3, Nov 29, 1997
- * by Mark Lord (probably), for 2.1.68
- * Updates for use with new IDE block driver.
- *
- * Version 0.4, Dec 14, 1997
- * by Jan Harkes
- * Fixed some errors and cleaned the code.
- *
- * Version 0.5, Jan 2, 1998
- * by Jaromir Koutek
- * Updates for use with (again) new IDE block driver.
- * Update of documentation.
- *
- * Version 0.6, Jan 2, 1999
- * by Jaromir Koutek
- * Reversed to version 0.3 of the driver, because
- * 0.5 doesn't work.
- */
-
-#include <linux/types.h>
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/pci.h>
-#include <linux/ide.h>
-
-#include <asm/io.h>
-
-#define DRV_NAME "opti621"
-
-#define READ_REG 0 /* index of Read cycle timing register */
-#define WRITE_REG 1 /* index of Write cycle timing register */
-#define CNTRL_REG 3 /* index of Control register */
-#define STRAP_REG 5 /* index of Strap register */
-#define MISC_REG 6 /* index of Miscellaneous register */
-
-static int reg_base;
-
-static DEFINE_SPINLOCK(opti621_lock);
-
-/* Write value to register reg, base of register
- * is at reg_base (0x1f0 primary, 0x170 secondary,
- * if not changed by PCI configuration).
- * This is from setupvic.exe program.
- */
-static void write_reg(u8 value, int reg)
-{
- inw(reg_base + 1);
- inw(reg_base + 1);
- outb(3, reg_base + 2);
- outb(value, reg_base + reg);
- outb(0x83, reg_base + 2);
-}
-
-/* Read value from register reg, base of register
- * is at reg_base (0x1f0 primary, 0x170 secondary,
- * if not changed by PCI configuration).
- * This is from setupvic.exe program.
- */
-static u8 read_reg(int reg)
-{
- u8 ret = 0;
-
- inw(reg_base + 1);
- inw(reg_base + 1);
- outb(3, reg_base + 2);
- ret = inb(reg_base + reg);
- outb(0x83, reg_base + 2);
-
- return ret;
-}
-
-static void opti621_set_pio_mode(ide_drive_t *drive, const u8 pio)
-{
- ide_hwif_t *hwif = drive->hwif;
- ide_drive_t *pair = ide_get_pair_dev(drive);
- unsigned long flags;
- u8 tim, misc, addr_pio = pio, clk;
-
- /* DRDY is default 2 (by OPTi Databook) */
- static const u8 addr_timings[2][5] = {
- { 0x20, 0x10, 0x00, 0x00, 0x00 }, /* 33 MHz */
- { 0x10, 0x10, 0x00, 0x00, 0x00 }, /* 25 MHz */
- };
- static const u8 data_rec_timings[2][5] = {
- { 0x5b, 0x45, 0x32, 0x21, 0x20 }, /* 33 MHz */
- { 0x48, 0x34, 0x21, 0x10, 0x10 } /* 25 MHz */
- };
-
- drive->drive_data = XFER_PIO_0 + pio;
-
- if (pair) {
- if (pair->drive_data && pair->drive_data < drive->drive_data)
- addr_pio = pair->drive_data - XFER_PIO_0;
- }
-
- spin_lock_irqsave(&opti621_lock, flags);
-
- reg_base = hwif->io_ports.data_addr;
-
- /* allow Register-B */
- outb(0xc0, reg_base + CNTRL_REG);
- /* hmm, setupvic.exe does this ;-) */
- outb(0xff, reg_base + 5);
- /* if reads 0xff, adapter not exist? */
- (void)inb(reg_base + CNTRL_REG);
- /* if reads 0xc0, no interface exist? */
- read_reg(CNTRL_REG);
-
- /* check CLK speed */
- clk = read_reg(STRAP_REG) & 1;
-
- printk(KERN_INFO "%s: CLK = %d MHz\n", hwif->name, clk ? 25 : 33);
-
- tim = data_rec_timings[clk][pio];
- misc = addr_timings[clk][addr_pio];
-
- /* select Index-0/1 for Register-A/B */
- write_reg(drive->dn & 1, MISC_REG);
- /* set read cycle timings */
- write_reg(tim, READ_REG);
- /* set write cycle timings */
- write_reg(tim, WRITE_REG);
-
- /* use Register-A for drive 0 */
- /* use Register-B for drive 1 */
- write_reg(0x85, CNTRL_REG);
-
- /* set address setup, DRDY timings, */
- /* and read prefetch for both drives */
- write_reg(misc, MISC_REG);
-
- spin_unlock_irqrestore(&opti621_lock, flags);
-}
-
-static const struct ide_port_ops opti621_port_ops = {
- .set_pio_mode = opti621_set_pio_mode,
-};
-
-static const struct ide_port_info opti621_chipset __devinitdata = {
- .name = DRV_NAME,
- .enablebits = { {0x45, 0x80, 0x00}, {0x40, 0x08, 0x00} },
- .port_ops = &opti621_port_ops,
- .host_flags = IDE_HFLAG_NO_DMA,
- .pio_mask = ATA_PIO4,
-};
-
-static int __devinit opti621_init_one(struct pci_dev *dev, const struct pci_device_id *id)
-{
- return ide_pci_init_one(dev, &opti621_chipset, NULL);
-}
-
-static const struct pci_device_id opti621_pci_tbl[] = {
- { PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C621), 0 },
- { PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C825), 0 },
- { 0, },
-};
-MODULE_DEVICE_TABLE(pci, opti621_pci_tbl);
-
-static struct pci_driver opti621_pci_driver = {
- .name = "Opti621_IDE",
- .id_table = opti621_pci_tbl,
- .probe = opti621_init_one,
- .remove = ide_pci_remove,
- .suspend = ide_pci_suspend,
- .resume = ide_pci_resume,
-};
-
-static int __init opti621_ide_init(void)
-{
- return ide_pci_register_driver(&opti621_pci_driver);
-}
-
-static void __exit opti621_ide_exit(void)
-{
- pci_unregister_driver(&opti621_pci_driver);
-}
-
-module_init(opti621_ide_init);
-module_exit(opti621_ide_exit);
-
-MODULE_AUTHOR("Jaromir Koutek, Jan Harkes, Mark Lord");
-MODULE_DESCRIPTION("PCI driver module for Opti621 IDE");
-MODULE_LICENSE("GPL");