diff options
Diffstat (limited to 'drivers/char/Kconfig')
| -rw-r--r-- | drivers/char/Kconfig | 60 |
1 files changed, 17 insertions, 43 deletions
diff --git a/drivers/char/Kconfig b/drivers/char/Kconfig index 0e6f35fcc2e..b10f4d8fdc7 100644 --- a/drivers/char/Kconfig +++ b/drivers/char/Kconfig @@ -201,6 +201,21 @@ config MOXA_SMARTIO The module will be called mxser. If you want to do that, say M here. +config MOXA_SMARTIO_NEW + tristate "Moxa SmartIO support v. 2.0 (EXPERIMENTAL)" + depends on SERIAL_NONSTANDARD + help + Say Y here if you have a Moxa SmartIO multiport serial card and/or + want to help develop a new version of this driver. + + This is upgraded (1.9.1) driver from original Moxa drivers with + changes finally resulting in PCI probing. + + Use at your own risk. + + This driver can also be built as a module. The module will be called + mxser_new. If you want to do that, say M here. + config ISI tristate "Multi-Tech multiport card support (EXPERIMENTAL)" depends on SERIAL_NONSTANDARD @@ -409,14 +424,6 @@ config SGI_MBCS If you have an SGI Altix with an attached SABrick say Y or M here, otherwise say N. -config MSPEC - tristate "Memory special operations driver" - depends on IA64 - help - If you have an ia64 and you want to enable memory special - operations support (formerly known as fetchop), say Y here, - otherwise say N. - source "drivers/serial/Kconfig" config UNIX98_PTYS @@ -863,39 +870,6 @@ config TANBAC_TB0219 depends TANBAC_TB022X select GPIO_VR41XX -menu "Ftape, the floppy tape device driver" - -config FTAPE - tristate "Ftape (QIC-80/Travan) support" - depends on BROKEN_ON_SMP && (ALPHA || X86) - ---help--- - If you have a tape drive that is connected to your floppy - controller, say Y here. - - Some tape drives (like the Seagate "Tape Store 3200" or the Iomega - "Ditto 3200" or the Exabyte "Eagle TR-3") come with a "high speed" - controller of their own. These drives (and their companion - controllers) are also supported if you say Y here. - - If you have a special controller (such as the CMS FC-10, FC-20, - Mountain Mach-II, or any controller that is based on the Intel 82078 - FDC like the high speed controllers by Seagate and Exabyte and - Iomega's "Ditto Dash") you must configure it by selecting the - appropriate entries from the "Floppy tape controllers" sub-menu - below and possibly modify the default values for the IRQ and DMA - channel and the IO base in ftape's configuration menu. - - If you want to use your floppy tape drive on a PCI-bus based system, - please read the file <file:drivers/char/ftape/README.PCI>. - - The ftape kernel driver is also available as a runtime loadable - module. To compile this driver as a module, choose M here: the - module will be called ftape. - -source "drivers/char/ftape/Kconfig" - -endmenu - source "drivers/char/agp/Kconfig" source "drivers/char/drm/Kconfig" @@ -1002,7 +976,7 @@ config HPET help If you say Y here, you will have a miscdevice named "/dev/hpet/". Each open selects one of the timers supported by the HPET. The timers are - non-periodioc and/or periodic. + non-periodic and/or periodic. config HPET_RTC_IRQ bool "HPET Control RTC IRQ" if !HPET_EMULATE_RTC @@ -1046,7 +1020,7 @@ source "drivers/char/tpm/Kconfig" config TELCLOCK tristate "Telecom clock driver for MPBL0010 ATCA SBC" - depends on EXPERIMENTAL + depends on EXPERIMENTAL && X86 default n help The telecom clock device is specific to the MPBL0010 ATCA computer and |