diff options
Diffstat (limited to 'drivers/ata/pata_pdc2027x.c')
| -rw-r--r-- | drivers/ata/pata_pdc2027x.c | 869 |
1 files changed, 869 insertions, 0 deletions
diff --git a/drivers/ata/pata_pdc2027x.c b/drivers/ata/pata_pdc2027x.c new file mode 100644 index 00000000000..56b8c1ee293 --- /dev/null +++ b/drivers/ata/pata_pdc2027x.c @@ -0,0 +1,869 @@ +/* + * Promise PATA TX2/TX4/TX2000/133 IDE driver for pdc20268 to pdc20277. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + * + * Ported to libata by: + * Albert Lee <albertcc@tw.ibm.com> IBM Corporation + * + * Copyright (C) 1998-2002 Andre Hedrick <andre@linux-ide.org> + * Portions Copyright (C) 1999 Promise Technology, Inc. + * + * Author: Frank Tiernan (frankt@promise.com) + * Released under terms of General Public License + * + * + * libata documentation is available via 'make {ps|pdf}docs', + * as Documentation/DocBook/libata.* + * + * Hardware information only available under NDA. + * + */ +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <linux/device.h> +#include <scsi/scsi.h> +#include <scsi/scsi_host.h> +#include <scsi/scsi_cmnd.h> +#include <linux/libata.h> +#include <asm/io.h> + +#define DRV_NAME "pata_pdc2027x" +#define DRV_VERSION "0.74-ac3" +#undef PDC_DEBUG + +#ifdef PDC_DEBUG +#define PDPRINTK(fmt, args...) printk(KERN_ERR "%s: " fmt, __FUNCTION__, ## args) +#else +#define PDPRINTK(fmt, args...) +#endif + +enum { + PDC_UDMA_100 = 0, + PDC_UDMA_133 = 1, + + PDC_100_MHZ = 100000000, + PDC_133_MHZ = 133333333, + + PDC_SYS_CTL = 0x1100, + PDC_ATA_CTL = 0x1104, + PDC_GLOBAL_CTL = 0x1108, + PDC_CTCR0 = 0x110C, + PDC_CTCR1 = 0x1110, + PDC_BYTE_COUNT = 0x1120, + PDC_PLL_CTL = 0x1202, +}; + +static int pdc2027x_init_one(struct pci_dev *pdev, const struct pci_device_id *ent); +static void pdc2027x_remove_one(struct pci_dev *pdev); +static void pdc2027x_error_handler(struct ata_port *ap); +static void pdc2027x_set_piomode(struct ata_port *ap, struct ata_device *adev); +static void pdc2027x_set_dmamode(struct ata_port *ap, struct ata_device *adev); +static void pdc2027x_post_set_mode(struct ata_port *ap); +static int pdc2027x_check_atapi_dma(struct ata_queued_cmd *qc); + +/* + * ATA Timing Tables based on 133MHz controller clock. + * These tables are only used when the controller is in 133MHz clock. + * If the controller is in 100MHz clock, the ASIC hardware will + * set the timing registers automatically when "set feature" command + * is issued to the device. However, if the controller clock is 133MHz, + * the following tables must be used. + */ +static struct pdc2027x_pio_timing { + u8 value0, value1, value2; +} pdc2027x_pio_timing_tbl [] = { + { 0xfb, 0x2b, 0xac }, /* PIO mode 0 */ + { 0x46, 0x29, 0xa4 }, /* PIO mode 1 */ + { 0x23, 0x26, 0x64 }, /* PIO mode 2 */ + { 0x27, 0x0d, 0x35 }, /* PIO mode 3, IORDY on, Prefetch off */ + { 0x23, 0x09, 0x25 }, /* PIO mode 4, IORDY on, Prefetch off */ +}; + +static struct pdc2027x_mdma_timing { + u8 value0, value1; +} pdc2027x_mdma_timing_tbl [] = { + { 0xdf, 0x5f }, /* MDMA mode 0 */ + { 0x6b, 0x27 }, /* MDMA mode 1 */ + { 0x69, 0x25 }, /* MDMA mode 2 */ +}; + +static struct pdc2027x_udma_timing { + u8 value0, value1, value2; +} pdc2027x_udma_timing_tbl [] = { + { 0x4a, 0x0f, 0xd5 }, /* UDMA mode 0 */ + { 0x3a, 0x0a, 0xd0 }, /* UDMA mode 1 */ + { 0x2a, 0x07, 0xcd }, /* UDMA mode 2 */ + { 0x1a, 0x05, 0xcd }, /* UDMA mode 3 */ + { 0x1a, 0x03, 0xcd }, /* UDMA mode 4 */ + { 0x1a, 0x02, 0xcb }, /* UDMA mode 5 */ + { 0x1a, 0x01, 0xcb }, /* UDMA mode 6 */ +}; + +static const struct pci_device_id pdc2027x_pci_tbl[] = { + { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20268, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PDC_UDMA_100 }, + { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20269, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PDC_UDMA_133 }, + { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20270, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PDC_UDMA_100 }, + { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20271, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PDC_UDMA_133 }, + { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20275, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PDC_UDMA_133 }, + { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20276, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PDC_UDMA_133 }, + { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20277, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PDC_UDMA_133 }, + { } /* terminate list */ +}; + +static struct pci_driver pdc2027x_pci_driver = { + .name = DRV_NAME, + .id_table = pdc2027x_pci_tbl, + .probe = pdc2027x_init_one, + .remove = __devexit_p(pdc2027x_remove_one), +}; + +static struct scsi_host_template pdc2027x_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static struct ata_port_operations pdc2027x_pata100_ops = { + .port_disable = ata_port_disable, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .check_atapi_dma = pdc2027x_check_atapi_dma, + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .data_xfer = ata_mmio_data_xfer, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = pdc2027x_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_pci_host_stop, +}; + +static struct ata_port_operations pdc2027x_pata133_ops = { + .port_disable = ata_port_disable, + .set_piomode = pdc2027x_set_piomode, + .set_dmamode = pdc2027x_set_dmamode, + .post_set_mode = pdc2027x_post_set_mode, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .check_atapi_dma = pdc2027x_check_atapi_dma, + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .data_xfer = ata_mmio_data_xfer, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = pdc2027x_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_pci_host_stop, +}; + +static struct ata_port_info pdc2027x_port_info[] = { + /* PDC_UDMA_100 */ + { + .sht = &pdc2027x_sht, + .flags = ATA_FLAG_NO_LEGACY | ATA_FLAG_SLAVE_POSS | + ATA_FLAG_MMIO, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma0-2 */ + .udma_mask = ATA_UDMA5, /* udma0-5 */ + .port_ops = &pdc2027x_pata100_ops, + }, + /* PDC_UDMA_133 */ + { + .sht = &pdc2027x_sht, + .flags = ATA_FLAG_NO_LEGACY | ATA_FLAG_SLAVE_POSS | + ATA_FLAG_MMIO, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma0-2 */ + .udma_mask = ATA_UDMA6, /* udma0-6 */ + .port_ops = &pdc2027x_pata133_ops, + }, +}; + +MODULE_AUTHOR("Andre Hedrick, Frank Tiernan, Albert Lee"); +MODULE_DESCRIPTION("libata driver module for Promise PDC20268 to PDC20277"); +MODULE_LICENSE("GPL"); +MODULE_VERSION(DRV_VERSION); +MODULE_DEVICE_TABLE(pci, pdc2027x_pci_tbl); + +/** + * port_mmio - Get the MMIO address of PDC2027x extended registers + * @ap: Port + * @offset: offset from mmio base + */ +static inline void* port_mmio(struct ata_port *ap, unsigned int offset) +{ + return ap->host->mmio_base + ap->port_no * 0x100 + offset; +} + +/** + * dev_mmio - Get the MMIO address of PDC2027x extended registers + * @ap: Port + * @adev: device + * @offset: offset from mmio base + */ +static inline void* dev_mmio(struct ata_port *ap, struct ata_device *adev, unsigned int offset) +{ + u8 adj = (adev->devno) ? 0x08 : 0x00; + return port_mmio(ap, offset) + adj; +} + +/** + * pdc2027x_pata_cbl_detect - Probe host controller cable detect info + * @ap: Port for which cable detect info is desired + * + * Read 80c cable indicator from Promise extended register. + * This register is latched when the system is reset. + * + * LOCKING: + * None (inherited from caller). + */ +static void pdc2027x_cbl_detect(struct ata_port *ap) +{ + u32 cgcr; + + /* check cable detect results */ + cgcr = readl(port_mmio(ap, PDC_GLOBAL_CTL)); + if (cgcr & (1 << 26)) + goto cbl40; + + PDPRINTK("No cable or 80-conductor cable on port %d\n", ap->port_no); + + ap->cbl = ATA_CBL_PATA80; + return; + +cbl40: + printk(KERN_INFO DRV_NAME ": 40-conductor cable detected on port %d\n", ap->port_no); + ap->cbl = ATA_CBL_PATA40; + ap->udma_mask &= ATA_UDMA_MASK_40C; +} + +/** + * pdc2027x_port_enabled - Check PDC ATA control register to see whether the port is enabled. + * @ap: Port to check + */ +static inline int pdc2027x_port_enabled(struct ata_port *ap) +{ + return readb(port_mmio(ap, PDC_ATA_CTL)) & 0x02; +} + +/** + * pdc2027x_prereset - prereset for PATA host controller + * @ap: Target port + * + * Probeinit including cable detection. + * + * LOCKING: + * None (inherited from caller). + */ + +static int pdc2027x_prereset(struct ata_port *ap) +{ + /* Check whether port enabled */ + if (!pdc2027x_port_enabled(ap)) { + printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id); + return 0; + } + pdc2027x_cbl_detect(ap); + return ata_std_prereset(ap); +} + +/** + * pdc2027x_error_handler - Perform reset on PATA port and classify + * @ap: Port to reset + * + * Reset PATA phy and classify attached devices. + * + * LOCKING: + * None (inherited from caller). + */ + +static void pdc2027x_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, pdc2027x_prereset, ata_std_softreset, NULL, ata_std_postreset); +} + +/** + * pdc2027x_set_piomode - Initialize host controller PATA PIO timings + * @ap: Port to configure + * @adev: um + * @pio: PIO mode, 0 - 4 + * + * Set PIO mode for device. + * + * LOCKING: + * None (inherited from caller). + */ + +static void pdc2027x_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + unsigned int pio = adev->pio_mode - XFER_PIO_0; + u32 ctcr0, ctcr1; + + PDPRINTK("adev->pio_mode[%X]\n", adev->pio_mode); + + /* Sanity check */ + if (pio > 4) { + printk(KERN_ERR DRV_NAME ": Unknown pio mode [%d] ignored\n", pio); + return; + + } + + /* Set the PIO timing registers using value table for 133MHz */ + PDPRINTK("Set pio regs... \n"); + + ctcr0 = readl(dev_mmio(ap, adev, PDC_CTCR0)); + ctcr0 &= 0xffff0000; + ctcr0 |= pdc2027x_pio_timing_tbl[pio].value0 | + (pdc2027x_pio_timing_tbl[pio].value1 << 8); + writel(ctcr0, dev_mmio(ap, adev, PDC_CTCR0)); + + ctcr1 = readl(dev_mmio(ap, adev, PDC_CTCR1)); + ctcr1 &= 0x00ffffff; + ctcr1 |= (pdc2027x_pio_timing_tbl[pio].value2 << 24); + writel(ctcr1, dev_mmio(ap, adev, PDC_CTCR1)); + + PDPRINTK("Set pio regs done\n"); + + PDPRINTK("Set to pio mode[%u] \n", pio); +} + +/** + * pdc2027x_set_dmamode - Initialize host controller PATA UDMA timings + * @ap: Port to configure + * @adev: um + * @udma: udma mode, XFER_UDMA_0 to XFER_UDMA_6 + * + * Set UDMA mode for device. + * + * LOCKING: + * None (inherited from caller). + */ +static void pdc2027x_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + unsigned int dma_mode = adev->dma_mode; + u32 ctcr0, ctcr1; + + if ((dma_mode >= XFER_UDMA_0) && + (dma_mode <= XFER_UDMA_6)) { + /* Set the UDMA timing registers with value table for 133MHz */ + unsigned int udma_mode = dma_mode & 0x07; + + if (dma_mode == XFER_UDMA_2) { + /* + * Turn off tHOLD. + * If tHOLD is '1', the hardware will add half clock for data hold time. + * This code segment seems to be no effect. tHOLD will be overwritten below. + */ + ctcr1 = readl(dev_mmio(ap, adev, PDC_CTCR1)); + writel(ctcr1 & ~(1 << 7), dev_mmio(ap, adev, PDC_CTCR1)); + } + + PDPRINTK("Set udma regs... \n"); + + ctcr1 = readl(dev_mmio(ap, adev, PDC_CTCR1)); + ctcr1 &= 0xff000000; + ctcr1 |= pdc2027x_udma_timing_tbl[udma_mode].value0 | + (pdc2027x_udma_timing_tbl[udma_mode].value1 << 8) | + (pdc2027x_udma_timing_tbl[udma_mode].value2 << 16); + writel(ctcr1, dev_mmio(ap, adev, PDC_CTCR1)); + + PDPRINTK("Set udma regs done\n"); + + PDPRINTK("Set to udma mode[%u] \n", udma_mode); + + } else if ((dma_mode >= XFER_MW_DMA_0) && + (dma_mode <= XFER_MW_DMA_2)) { + /* Set the MDMA timing registers with value table for 133MHz */ + unsigned int mdma_mode = dma_mode & 0x07; + + PDPRINTK("Set mdma regs... \n"); + ctcr0 = readl(dev_mmio(ap, adev, PDC_CTCR0)); + + ctcr0 &= 0x0000ffff; + ctcr0 |= (pdc2027x_mdma_timing_tbl[mdma_mode].value0 << 16) | + (pdc2027x_mdma_timing_tbl[mdma_mode].value1 << 24); + + writel(ctcr0, dev_mmio(ap, adev, PDC_CTCR0)); + PDPRINTK("Set mdma regs done\n"); + + PDPRINTK("Set to mdma mode[%u] \n", mdma_mode); + } else { + printk(KERN_ERR DRV_NAME ": Unknown dma mode [%u] ignored\n", dma_mode); + } +} + +/** + * pdc2027x_post_set_mode - Set the timing registers back to correct values. + * @ap: Port to configure + * + * The pdc2027x hardware will look at "SET FEATURES" and change the timing registers + * automatically. The values set by the hardware might be incorrect, under 133Mhz PLL. + * This function overwrites the possibly incorrect values set by the hardware to be correct. + */ +static void pdc2027x_post_set_mode(struct ata_port *ap) +{ + int i; + + for (i = 0; i < ATA_MAX_DEVICES; i++) { + struct ata_device *dev = &ap->device[i]; + + if (ata_dev_enabled(dev)) { + + pdc2027x_set_piomode(ap, dev); + + /* + * Enable prefetch if the device support PIO only. + */ + if (dev->xfer_shift == ATA_SHIFT_PIO) { + u32 ctcr1 = readl(dev_mmio(ap, dev, PDC_CTCR1)); + ctcr1 |= (1 << 25); + writel(ctcr1, dev_mmio(ap, dev, PDC_CTCR1)); + + PDPRINTK("Turn on prefetch\n"); + } else { + pdc2027x_set_dmamode(ap, dev); + } + } + } +} + +/** + * pdc2027x_check_atapi_dma - Check whether ATAPI DMA can be supported for this command + * @qc: Metadata associated with taskfile to check + * + * LOCKING: + * None (inherited from caller). + * + * RETURNS: 0 when ATAPI DMA can be used + * 1 otherwise + */ +static int pdc2027x_check_atapi_dma(struct ata_queued_cmd *qc) +{ + struct scsi_cmnd *cmd = qc->scsicmd; + u8 *scsicmd = cmd->cmnd; + int rc = 1; /* atapi dma off by default */ + + /* + * This workaround is from Promise's GPL driver. + * If ATAPI DMA is used for commands not in the + * following white list, say MODE_SENSE and REQUEST_SENSE, + * pdc2027x might hit the irq lost problem. + */ + switch (scsicmd[0]) { + case READ_10: + case WRITE_10: + case READ_12: + case WRITE_12: + case READ_6: + case WRITE_6: + case 0xad: /* READ_DVD_STRUCTURE */ + case 0xbe: /* READ_CD */ + /* ATAPI DMA is ok */ + rc = 0; + break; + default: + ; + } + + return rc; +} + +/** + * pdc_read_counter - Read the ctr counter + * @probe_ent: for the port address + */ + +static long pdc_read_counter(struct ata_probe_ent *probe_ent) +{ + long counter; + int retry = 1; + u32 bccrl, bccrh, bccrlv, bccrhv; + +retry: + bccrl = readl(probe_ent->mmio_base + PDC_BYTE_COUNT) & 0xffff; + bccrh = readl(probe_ent->mmio_base + PDC_BYTE_COUNT + 0x100) & 0xffff; + rmb(); + + /* Read the counter values again for verification */ + bccrlv = readl(probe_ent->mmio_base + PDC_BYTE_COUNT) & 0xffff; + bccrhv = readl(probe_ent->mmio_base + PDC_BYTE_COUNT + 0x100) & 0xffff; + rmb(); + + counter = (bccrh << 15) | bccrl; + + PDPRINTK("bccrh [%X] bccrl [%X]\n", bccrh, bccrl); + PDPRINTK("bccrhv[%X] bccrlv[%X]\n", bccrhv, bccrlv); + + /* + * The 30-bit decreasing counter are read by 2 pieces. + * Incorrect value may be read when both bccrh and bccrl are changing. + * Ex. When 7900 decrease to 78FF, wrong value 7800 might be read. + */ + if (retry && !(bccrh == bccrhv && bccrl >= bccrlv)) { + retry--; + PDPRINTK("rereading counter\n"); + goto retry; + } + + return counter; +} + +/** + * adjust_pll - Adjust the PLL input clock in Hz. + * + * @pdc_controller: controller specific information + * @probe_ent: For the port address + * @pll_clock: The input of PLL in HZ + */ +static void pdc_adjust_pll(struct ata_probe_ent *probe_ent, long pll_clock, unsigned int board_idx) +{ + + u16 pll_ctl; + long pll_clock_khz = pll_clock / 1000; + long pout_required = board_idx? PDC_133_MHZ:PDC_100_MHZ; + long ratio = pout_required / pll_clock_khz; + int F, R; + + /* Sanity check */ + if (unlikely(pll_clock_khz < 5000L || pll_clock_khz > 70000L)) { + printk(KERN_ERR DRV_NAME ": Invalid PLL input clock %ldkHz, give up!\n", pll_clock_khz); + return; + } + +#ifdef PDC_DEBUG + PDPRINTK("pout_required is %ld\n", pout_required); + + /* Show the current clock value of PLL control register + * (maybe already configured by the firmware) + */ + pll_ctl = readw(probe_ent->mmio_base + PDC_PLL_CTL); + + PDPRINTK("pll_ctl[%X]\n", pll_ctl); +#endif + + /* + * Calculate the ratio of F, R and OD + * POUT = (F + 2) / (( R + 2) * NO) + */ + if (ratio < 8600L) { /* 8.6x */ + /* Using NO = 0x01, R = 0x0D */ + R = 0x0d; + } else if (ratio < 12900L) { /* 12.9x */ + /* Using NO = 0x01, R = 0x08 */ + R = 0x08; + } else if (ratio < 16100L) { /* 16.1x */ + /* Using NO = 0x01, R = 0x06 */ + R = 0x06; + } else if (ratio < 64000L) { /* 64x */ + R = 0x00; + } else { + /* Invalid ratio */ + printk(KERN_ERR DRV_NAME ": Invalid ratio %ld, give up!\n", ratio); + return; + } + + F = (ratio * (R+2)) / 1000 - 2; + + if (unlikely(F < 0 || F > 127)) { + /* Invalid F */ + printk(KERN_ERR DRV_NAME ": F[%d] invalid!\n", F); + return; + } + + PDPRINTK("F[%d] R[%d] ratio*1000[%ld]\n", F, R, ratio); + + pll_ctl = (R << 8) | F; + + PDPRINTK("Writing pll_ctl[%X]\n", pll_ctl); + + writew(pll_ctl, probe_ent->mmio_base + PDC_PLL_CTL); + readw(probe_ent->mmio_base + PDC_PLL_CTL); /* flush */ + + /* Wait the PLL circuit to be stable */ + mdelay(30); + +#ifdef PDC_DEBUG + /* + * Show the current clock value of PLL control register + * (maybe configured by the firmware) + */ + pll_ctl = readw(probe_ent->mmio_base + PDC_PLL_CTL); + + PDPRINTK("pll_ctl[%X]\n", pll_ctl); +#endif + + return; +} + +/** + * detect_pll_input_clock - Detect the PLL input clock in Hz. + * @probe_ent: for the port address + * Ex. 16949000 on 33MHz PCI bus for pdc20275. + * Half of the PCI clock. + */ +static long pdc_detect_pll_input_clock(struct ata_probe_ent *probe_ent) +{ + u32 scr; + long start_count, end_count; + long pll_clock; + + /* Read current counter value */ + start_count = pdc_read_counter(probe_ent); + + /* Start the test mode */ + scr = readl(probe_ent->mmio_base + PDC_SYS_CTL); + PDPRINTK("scr[%X]\n", scr); + writel(scr | (0x01 << 14), probe_ent->mmio_base + PDC_SYS_CTL); + readl(probe_ent->mmio_base + PDC_SYS_CTL); /* flush */ + + /* Let the counter run for 100 ms. */ + mdelay(100); + + /* Read the counter values again */ + end_count = pdc_read_counter(probe_ent); + + /* Stop the test mode */ + scr = readl(probe_ent->mmio_base + PDC_SYS_CTL); + PDPRINTK("scr[%X]\n", scr); + writel(scr & ~(0x01 << 14), probe_ent->mmio_base + PDC_SYS_CTL); + readl(probe_ent->mmio_base + PDC_SYS_CTL); /* flush */ + + /* calculate the input clock in Hz */ + pll_clock = (start_count - end_count) * 10; + + PDPRINTK("start[%ld] end[%ld] \n", start_count, end_count); + PDPRINTK("PLL input clock[%ld]Hz\n", pll_clock); + + return pll_clock; +} + +/** + * pdc_hardware_init - Initialize the hardware. + * @pdev: instance of pci_dev found + * @pdc_controller: controller specific information + * @pe: for the port address + */ +static int pdc_hardware_init(struct pci_dev *pdev, struct ata_probe_ent *pe, unsigned int board_idx) +{ + long pll_clock; + + /* + * Detect PLL input clock rate. + * On some system, where PCI bus is running at non-standard clock rate. + * Ex. 25MHz or 40MHz, we have to adjust the cycle_time. + * The pdc20275 controller employs PLL circuit to help correct timing registers setting. + */ + pll_clock = pdc_detect_pll_input_clock(pe); + + if (pll_clock < 0) /* counter overflow? Try again. */ + pll_clock = pdc_detect_pll_input_clock(pe); + + dev_printk(KERN_INFO, &pdev->dev, "PLL input clock %ld kHz\n", pll_clock/1000); + + /* Adjust PLL control register */ + pdc_adjust_pll(pe, pll_clock, board_idx); + + return 0; +} + +/** + * pdc_ata_setup_port - setup the mmio address + * @port: ata ioports to setup + * @base: base address + */ +static void pdc_ata_setup_port(struct ata_ioports *port, unsigned long base) +{ + port->cmd_addr = + port->data_addr = base; + port->feature_addr = + port->error_addr = base + 0x05; + port->nsect_addr = base + 0x0a; + port->lbal_addr = base + 0x0f; + port->lbam_addr = base + 0x10; + port->lbah_addr = base + 0x15; + port->device_addr = base + 0x1a; + port->command_addr = + port->status_addr = base + 0x1f; + port->altstatus_addr = + port->ctl_addr = base + 0x81a; +} + +/** + * pdc2027x_init_one - PCI probe function + * Called when an instance of PCI adapter is inserted. + * This function checks whether the hardware is supported, + * initialize hardware and register an instance of ata_host to + * libata by providing struct ata_probe_ent and ata_device_add(). + * (implements struct pci_driver.probe() ) + * + * @pdev: instance of pci_dev found + * @ent: matching entry in the id_tbl[] + */ +static int __devinit pdc2027x_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) +{ + static int printed_version; + unsigned int board_idx = (unsigned int) ent->driver_data; + + struct ata_probe_ent *probe_ent = NULL; + unsigned long base; + void *mmio_base; + int rc; + + if (!printed_version++) + dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n"); + + rc = pci_enable_device(pdev); + if (rc) + return rc; + + rc = pci_request_regions(pdev, DRV_NAME); + if (rc) + goto err_out; + + rc = pci_set_dma_mask(pdev, ATA_DMA_MASK); + if (rc) + goto err_out_regions; + + rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK); + if (rc) + goto err_out_regions; + + /* Prepare the probe entry */ + probe_ent = kzalloc(sizeof(*probe_ent), GFP_KERNEL); + if (probe_ent == NULL) { + rc = -ENOMEM; + goto err_out_regions; + } + + probe_ent->dev = pci_dev_to_dev(pdev); + INIT_LIST_HEAD(&probe_ent->node); + + mmio_base = pci_iomap(pdev, 5, 0); + if (!mmio_base) { + rc = -ENOMEM; + goto err_out_free_ent; + } + + base = (unsigned long) mmio_base; + + probe_ent->sht = pdc2027x_port_info[board_idx].sht; + probe_ent->port_flags = pdc2027x_port_info[board_idx].flags; + probe_ent->pio_mask = pdc2027x_port_info[board_idx].pio_mask; + probe_ent->mwdma_mask = pdc2027x_port_info[board_idx].mwdma_mask; + probe_ent->udma_mask = pdc2027x_port_info[board_idx].udma_mask; + probe_ent->port_ops = pdc2027x_port_info[board_idx].port_ops; + + probe_ent->irq = pdev->irq; + probe_ent->irq_flags = SA_SHIRQ; + probe_ent->mmio_base = mmio_base; + + pdc_ata_setup_port(&probe_ent->port[0], base + 0x17c0); + probe_ent->port[0].bmdma_addr = base + 0x1000; + pdc_ata_setup_port(&probe_ent->port[1], base + 0x15c0); + probe_ent->port[1].bmdma_addr = base + 0x1008; + + probe_ent->n_ports = 2; + + pci_set_master(pdev); + //pci_enable_intx(pdev); + + /* initialize adapter */ + if (pdc_hardware_init(pdev, probe_ent, board_idx) != 0) + goto err_out_free_ent; + + ata_device_add(probe_ent); + kfree(probe_ent); + + return 0; + +err_out_free_ent: + kfree(probe_ent); +err_out_regions: + pci_release_regions(pdev); +err_out: + pci_disable_device(pdev); + return rc; +} + +/** + * pdc2027x_remove_one - Called to remove a single instance of the + * adapter. + * + * @dev: The PCI device to remove. + * FIXME: module load/unload not working yet + */ +static void __devexit pdc2027x_remove_one(struct pci_dev *pdev) +{ + ata_pci_remove_one(pdev); +} + +/** + * pdc2027x_init - Called after this module is loaded into the kernel. + */ +static int __init pdc2027x_init(void) +{ + return pci_module_init(&pdc2027x_pci_driver); +} + +/** + * pdc2027x_exit - Called before this module unloaded from the kernel + */ +static void __exit pdc2027x_exit(void) +{ + pci_unregister_driver(&pdc2027x_pci_driver); +} + +module_init(pdc2027x_init); +module_exit(pdc2027x_exit); |