diff options
Diffstat (limited to 'drivers/ata/pata_opti.c')
| -rw-r--r-- | drivers/ata/pata_opti.c | 163 |
1 files changed, 36 insertions, 127 deletions
diff --git a/drivers/ata/pata_opti.c b/drivers/ata/pata_opti.c index 57fe21f3a97..3a944a02926 100644 --- a/drivers/ata/pata_opti.c +++ b/drivers/ata/pata_opti.c @@ -1,7 +1,6 @@ /* * pata_opti.c - ATI PATA for new ATA layer * (C) 2005 Red Hat Inc - * Alan Cox <alan@redhat.com> * * Based on * linux/drivers/ide/pci/opti621.c Version 0.7 Sept 10, 2002 @@ -27,14 +26,13 @@ #include <linux/kernel.h> #include <linux/module.h> #include <linux/pci.h> -#include <linux/init.h> #include <linux/blkdev.h> #include <linux/delay.h> #include <scsi/scsi_host.h> #include <linux/libata.h> #define DRV_NAME "pata_opti" -#define DRV_VERSION "0.2.5" +#define DRV_VERSION "0.2.9" enum { READ_REG = 0, /* index of Read cycle timing register */ @@ -46,13 +44,15 @@ enum { /** * opti_pre_reset - probe begin - * @ap: ATA port + * @link: ATA link + * @deadline: deadline jiffies for the operation * * Set up cable type and use generic probe init */ -static int opti_pre_reset(struct ata_port *ap) +static int opti_pre_reset(struct ata_link *link, unsigned long deadline) { + struct ata_port *ap = link->ap; struct pci_dev *pdev = to_pci_dev(ap->host->dev); static const struct pci_bits opti_enable_bits[] = { { 0x45, 1, 0x80, 0x00 }, @@ -62,23 +62,7 @@ static int opti_pre_reset(struct ata_port *ap) if (!pci_test_config_bits(pdev, &opti_enable_bits[ap->port_no])) return -ENOENT; - ap->cbl = ATA_CBL_PATA40; - return ata_std_prereset(ap); -} - -/** - * opti_probe_reset - probe reset - * @ap: ATA port - * - * Perform the ATA probe and bus reset sequence plus specific handling - * for this hardware. The Opti needs little handling - we have no UDMA66 - * capability that needs cable detection. All we must do is check the port - * is enabled. - */ - -static void opti_error_handler(struct ata_port *ap) -{ - ata_bmdma_drive_eh(ap, opti_pre_reset, ata_std_softreset, NULL, ata_std_postreset); + return ata_sff_prereset(link, deadline); } /** @@ -95,43 +79,19 @@ static void opti_error_handler(struct ata_port *ap) static void opti_write_reg(struct ata_port *ap, u8 val, int reg) { - unsigned long regio = ap->ioaddr.cmd_addr; + void __iomem *regio = ap->ioaddr.cmd_addr; /* These 3 unlock the control register access */ - inw(regio + 1); - inw(regio + 1); - outb(3, regio + 2); + ioread16(regio + 1); + ioread16(regio + 1); + iowrite8(3, regio + 2); /* Do the I/O */ - outb(val, regio + reg); + iowrite8(val, regio + reg); /* Relock */ - outb(0x83, regio + 2); -} - -#if 0 -/** - * opti_read_reg - control register read - * @ap: ATA port - * @reg: control register number - * - * The Opti uses magic 'trapdoor' register accesses to do configuration - * rather than using PCI space as other controllers do. The double inw - * on the error register activates configuration mode. We can then read - * the control register - */ - -static u8 opti_read_reg(struct ata_port *ap, int reg) -{ - unsigned long regio = ap->ioaddr.cmd_addr; - u8 ret; - inw(regio + 1); - inw(regio + 1); - outb(3, regio + 2); - ret = inb(regio + reg); - outb(0x83, regio + 2); + iowrite8(0x83, regio + 2); } -#endif /** * opti_set_piomode - set initial PIO mode data @@ -148,7 +108,7 @@ static void opti_set_piomode(struct ata_port *ap, struct ata_device *adev) struct ata_device *pair = ata_dev_pair(adev); int clock; int pio = adev->pio_mode - XFER_PIO_0; - unsigned long regio = ap->ioaddr.cmd_addr; + void __iomem *regio = ap->ioaddr.cmd_addr; u8 addr; /* Address table precomputed with prefetch off and a DCLK of 2 */ @@ -161,8 +121,8 @@ static void opti_set_piomode(struct ata_port *ap, struct ata_device *adev) { 0x58, 0x44, 0x32, 0x22, 0x21 } }; - outb(0xff, regio + 5); - clock = inw(regio + 5) & 1; + iowrite8(0xff, regio + 5); + clock = ioread16(regio + 5) & 1; /* * As with many controllers the address setup time is shared @@ -188,103 +148,52 @@ static void opti_set_piomode(struct ata_port *ap, struct ata_device *adev) } static struct scsi_host_template opti_sht = { - .module = THIS_MODULE, - .name = DRV_NAME, - .ioctl = ata_scsi_ioctl, - .queuecommand = ata_scsi_queuecmd, - .can_queue = ATA_DEF_QUEUE, - .this_id = ATA_SHT_THIS_ID, - .sg_tablesize = LIBATA_MAX_PRD, - .max_sectors = ATA_MAX_SECTORS, - .cmd_per_lun = ATA_SHT_CMD_PER_LUN, - .emulated = ATA_SHT_EMULATED, - .use_clustering = ATA_SHT_USE_CLUSTERING, - .proc_name = DRV_NAME, - .dma_boundary = ATA_DMA_BOUNDARY, - .slave_configure = ata_scsi_slave_config, - .bios_param = ata_std_bios_param, + ATA_PIO_SHT(DRV_NAME), }; static struct ata_port_operations opti_port_ops = { - .port_disable = ata_port_disable, + .inherits = &ata_sff_port_ops, + .cable_detect = ata_cable_40wire, .set_piomode = opti_set_piomode, -/* .set_dmamode = opti_set_dmamode, */ - .tf_load = ata_tf_load, - .tf_read = ata_tf_read, - .check_status = ata_check_status, - .exec_command = ata_exec_command, - .dev_select = ata_std_dev_select, - - .freeze = ata_bmdma_freeze, - .thaw = ata_bmdma_thaw, - .error_handler = opti_error_handler, - .post_internal_cmd = ata_bmdma_post_internal_cmd, - - .bmdma_setup = ata_bmdma_setup, - .bmdma_start = ata_bmdma_start, - .bmdma_stop = ata_bmdma_stop, - .bmdma_status = ata_bmdma_status, - - .qc_prep = ata_qc_prep, - .qc_issue = ata_qc_issue_prot, - - .data_xfer = ata_pio_data_xfer, - - .irq_handler = ata_interrupt, - .irq_clear = ata_bmdma_irq_clear, - - .port_start = ata_port_start, - .port_stop = ata_port_stop, - .host_stop = ata_host_stop + .prereset = opti_pre_reset, }; static int opti_init_one(struct pci_dev *dev, const struct pci_device_id *id) { - static struct ata_port_info info = { - .sht = &opti_sht, - .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, - .pio_mask = 0x1f, + static const struct ata_port_info info = { + .flags = ATA_FLAG_SLAVE_POSS, + .pio_mask = ATA_PIO4, .port_ops = &opti_port_ops }; - static struct ata_port_info *port_info[2] = { &info, &info }; - static int printed_version; + const struct ata_port_info *ppi[] = { &info, NULL }; - if (!printed_version++) - dev_printk(KERN_DEBUG, &dev->dev, "version " DRV_VERSION "\n"); + ata_print_version_once(&dev->dev, DRV_VERSION); - return ata_pci_init_one(dev, port_info, 2); + return ata_pci_sff_init_one(dev, ppi, &opti_sht, NULL, 0); } static const struct pci_device_id opti[] = { - { PCI_VENDOR_ID_OPTI, PCI_DEVICE_ID_OPTI_82C621, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, - { PCI_VENDOR_ID_OPTI, PCI_DEVICE_ID_OPTI_82C825, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1}, - { 0, }, + { PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C621), 0 }, + { PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C825), 1 }, + + { }, }; static struct pci_driver opti_pci_driver = { - .name = DRV_NAME, + .name = DRV_NAME, .id_table = opti, .probe = opti_init_one, - .remove = ata_pci_remove_one + .remove = ata_pci_remove_one, +#ifdef CONFIG_PM_SLEEP + .suspend = ata_pci_device_suspend, + .resume = ata_pci_device_resume, +#endif }; -static int __init opti_init(void) -{ - return pci_register_driver(&opti_pci_driver); -} - - -static void __exit opti_exit(void) -{ - pci_unregister_driver(&opti_pci_driver); -} - +module_pci_driver(opti_pci_driver); MODULE_AUTHOR("Alan Cox"); MODULE_DESCRIPTION("low-level driver for Opti 621/621X"); MODULE_LICENSE("GPL"); MODULE_DEVICE_TABLE(pci, opti); MODULE_VERSION(DRV_VERSION); - -module_init(opti_init); -module_exit(opti_exit); |