diff options
Diffstat (limited to 'drivers/ata/pata_ali.c')
| -rw-r--r-- | drivers/ata/pata_ali.c | 189 |
1 files changed, 115 insertions, 74 deletions
diff --git a/drivers/ata/pata_ali.c b/drivers/ata/pata_ali.c index 0f3e659db99..d19cd88ed2d 100644 --- a/drivers/ata/pata_ali.c +++ b/drivers/ata/pata_ali.c @@ -1,7 +1,6 @@ /* * pata_ali.c - ALI 15x3 PATA for new ATA layer * (C) 2005 Red Hat Inc - * Alan Cox <alan@redhat.com> * * based in part upon * linux/drivers/ide/pci/alim15x3.c Version 0.17 2003/01/02 @@ -20,7 +19,9 @@ * * TODO/CHECK * Cannot have ATAPI on both master & slave for rev < c2 (???) but - * otherwise should do atapi DMA. + * otherwise should do atapi DMA (For now for old we do PIO only for + * ATAPI) + * Review Sunblade workaround. */ #include <linux/kernel.h> @@ -34,12 +35,14 @@ #include <linux/dmi.h> #define DRV_NAME "pata_ali" -#define DRV_VERSION "0.7.5" +#define DRV_VERSION "0.7.8" static int ali_atapi_dma = 0; module_param_named(atapi_dma, ali_atapi_dma, int, 0644); MODULE_PARM_DESC(atapi_dma, "Enable ATAPI DMA (0=disable, 1=enable)"); +static struct pci_dev *ali_isa_bridge; + /* * Cable special cases */ @@ -53,7 +56,7 @@ static const struct dmi_system_id cable_dmi_table[] = { }, }, { - .ident = "Toshiba Satelite S1800-814", + .ident = "Toshiba Satellite S1800-814", .matches = { DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"), DMI_MATCH(DMI_PRODUCT_NAME, "S1800-814"), @@ -121,7 +124,7 @@ static unsigned long ali_20_filter(struct ata_device *adev, unsigned long mask) ata_id_c_string(adev->id, model_num, ATA_ID_PROD, sizeof(model_num)); if (strstr(model_num, "WDC")) return mask &= ~ATA_MASK_UDMA; - return ata_bmdma_mode_filter(adev, mask); + return mask; } /** @@ -148,8 +151,7 @@ static void ali_fifo_control(struct ata_port *ap, struct ata_device *adev, int o pci_read_config_byte(pdev, pio_fifo, &fifo); fifo &= ~(0x0F << shift); - if (on) - fifo |= (on << shift); + fifo |= (on << shift); pci_write_config_byte(pdev, pio_fifo, fifo); } @@ -157,8 +159,7 @@ static void ali_fifo_control(struct ata_port *ap, struct ata_device *adev, int o * ali_program_modes - load mode registers * @ap: ALi channel to load * @adev: Device the timing is for - * @cmd: Command timing - * @data: Data timing + * @t: timing data * @ultra: UDMA timing or zero for off * * Loads the timing registers for cmd/data and disable UDMA if @@ -200,8 +201,7 @@ static void ali_program_modes(struct ata_port *ap, struct ata_device *adev, stru * @ap: ATA interface * @adev: ATA device * - * Program the ALi registers for PIO mode. FIXME: add timings for - * PIO5. + * Program the ALi registers for PIO mode. */ static void ali_set_piomode(struct ata_port *ap, struct ata_device *adev) @@ -235,7 +235,7 @@ static void ali_set_piomode(struct ata_port *ap, struct ata_device *adev) * @ap: ATA interface * @adev: ATA device * - * FIXME: MWDMA timings + * Program the ALi registers for DMA mode. */ static void ali_set_dmamode(struct ata_port *ap, struct ata_device *adev) @@ -287,10 +287,10 @@ static void ali_warn_atapi_dma(struct ata_device *adev) int print_info = ehc->i.flags & ATA_EHI_PRINTINFO; if (print_info && adev->class == ATA_DEV_ATAPI && !ali_atapi_dma) { - ata_dev_printk(adev, KERN_WARNING, - "WARNING: ATAPI DMA disabled for reliablity issues. It can be enabled\n"); - ata_dev_printk(adev, KERN_WARNING, - "WARNING: via pata_ali.atapi_dma modparam or corresponding sysfs node.\n"); + ata_dev_warn(adev, + "WARNING: ATAPI DMA disabled for reliability issues. It can be enabled\n"); + ata_dev_warn(adev, + "WARNING: via pata_ali.atapi_dma modparam or corresponding sysfs node.\n"); } } @@ -338,6 +338,23 @@ static int ali_check_atapi_dma(struct ata_queued_cmd *qc) return 0; } +static void ali_c2_c3_postreset(struct ata_link *link, unsigned int *classes) +{ + u8 r; + int port_bit = 4 << link->ap->port_no; + + /* If our bridge is an ALI 1533 then do the extra work */ + if (ali_isa_bridge) { + /* Tristate and re-enable the bus signals */ + pci_read_config_byte(ali_isa_bridge, 0x58, &r); + r &= ~port_bit; + pci_write_config_byte(ali_isa_bridge, 0x58, r); + r |= port_bit; + pci_write_config_byte(ali_isa_bridge, 0x58, r); + } + ata_sff_postreset(link, classes); +} + static struct scsi_host_template ali_sht = { ATA_BMDMA_SHT(DRV_NAME), }; @@ -350,10 +367,11 @@ static struct ata_port_operations ali_early_port_ops = { .inherits = &ata_sff_port_ops, .cable_detect = ata_cable_40wire, .set_piomode = ali_set_piomode, + .sff_data_xfer = ata_sff_data_xfer32, }; static const struct ata_port_operations ali_dma_base_ops = { - .inherits = &ata_bmdma_port_ops, + .inherits = &ata_bmdma32_port_ops, .set_piomode = ali_set_piomode, .set_dmamode = ali_set_dmamode, }; @@ -378,6 +396,17 @@ static struct ata_port_operations ali_c2_port_ops = { .check_atapi_dma = ali_check_atapi_dma, .cable_detect = ali_c2_cable_detect, .dev_config = ali_lock_sectors, + .postreset = ali_c2_c3_postreset, +}; + +/* + * Port operations for DMA capable ALi with cable detect + */ +static struct ata_port_operations ali_c4_port_ops = { + .inherits = &ali_dma_base_ops, + .check_atapi_dma = ali_check_atapi_dma, + .cable_detect = ali_c2_cable_detect, + .dev_config = ali_lock_sectors, }; /* @@ -402,52 +431,51 @@ static struct ata_port_operations ali_c5_port_ops = { static void ali_init_chipset(struct pci_dev *pdev) { u8 tmp; - struct pci_dev *north, *isa_bridge; + struct pci_dev *north; /* * The chipset revision selects the driver operations and * mode data. */ - if (pdev->revision >= 0x20 && pdev->revision < 0xC2) { - /* 1543-E/F, 1543C-C, 1543C-D, 1543C-E */ - pci_read_config_byte(pdev, 0x4B, &tmp); - /* Clear CD-ROM DMA write bit */ - tmp &= 0x7F; - pci_write_config_byte(pdev, 0x4B, tmp); - } else if (pdev->revision >= 0xC2) { - /* Enable cable detection logic */ + if (pdev->revision <= 0x20) { + pci_read_config_byte(pdev, 0x53, &tmp); + tmp |= 0x03; + pci_write_config_byte(pdev, 0x53, tmp); + } else { + pci_read_config_byte(pdev, 0x4a, &tmp); + pci_write_config_byte(pdev, 0x4a, tmp | 0x20); pci_read_config_byte(pdev, 0x4B, &tmp); + if (pdev->revision < 0xC2) + /* 1543-E/F, 1543C-C, 1543C-D, 1543C-E */ + /* Clear CD-ROM DMA write bit */ + tmp &= 0x7F; + /* Cable and UDMA */ + if (pdev->revision >= 0xc2) + tmp |= 0x01; pci_write_config_byte(pdev, 0x4B, tmp | 0x08); - } - north = pci_get_bus_and_slot(0, PCI_DEVFN(0,0)); - isa_bridge = pci_get_device(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, NULL); - - if (north && north->vendor == PCI_VENDOR_ID_AL && isa_bridge) { - /* Configure the ALi bridge logic. For non ALi rely on BIOS. - Set the south bridge enable bit */ - pci_read_config_byte(isa_bridge, 0x79, &tmp); - if (pdev->revision == 0xC2) - pci_write_config_byte(isa_bridge, 0x79, tmp | 0x04); - else if (pdev->revision > 0xC2 && pdev->revision < 0xC5) - pci_write_config_byte(isa_bridge, 0x79, tmp | 0x02); - } - if (pdev->revision >= 0x20) { /* * CD_ROM DMA on (0x53 bit 0). Enable this even if we want * to use PIO. 0x53 bit 1 (rev 20 only) - enable FIFO control * via 0x54/55. */ pci_read_config_byte(pdev, 0x53, &tmp); - if (pdev->revision <= 0x20) - tmp &= ~0x02; if (pdev->revision >= 0xc7) tmp |= 0x03; else tmp |= 0x01; /* CD_ROM enable for DMA */ pci_write_config_byte(pdev, 0x53, tmp); } - pci_dev_put(isa_bridge); + north = pci_get_bus_and_slot(0, PCI_DEVFN(0,0)); + if (north && north->vendor == PCI_VENDOR_ID_AL && ali_isa_bridge) { + /* Configure the ALi bridge logic. For non ALi rely on BIOS. + Set the south bridge enable bit */ + pci_read_config_byte(ali_isa_bridge, 0x79, &tmp); + if (pdev->revision == 0xC2) + pci_write_config_byte(ali_isa_bridge, 0x79, tmp | 0x04); + else if (pdev->revision > 0xC2 && pdev->revision < 0xC5) + pci_write_config_byte(ali_isa_bridge, 0x79, tmp | 0x02); + } pci_dev_put(north); ata_pci_bmdma_clear_simplex(pdev); } @@ -464,60 +492,64 @@ static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id) { static const struct ata_port_info info_early = { .flags = ATA_FLAG_SLAVE_POSS, - .pio_mask = 0x1f, + .pio_mask = ATA_PIO4, .port_ops = &ali_early_port_ops }; /* Revision 0x20 added DMA */ static const struct ata_port_info info_20 = { - .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_PIO_LBA48, - .pio_mask = 0x1f, - .mwdma_mask = 0x07, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_PIO_LBA48 | + ATA_FLAG_IGN_SIMPLEX, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA2, .port_ops = &ali_20_port_ops }; /* Revision 0x20 with support logic added UDMA */ static const struct ata_port_info info_20_udma = { - .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_PIO_LBA48, - .pio_mask = 0x1f, - .mwdma_mask = 0x07, - .udma_mask = 0x07, /* UDMA33 */ + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_PIO_LBA48 | + ATA_FLAG_IGN_SIMPLEX, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA2, + .udma_mask = ATA_UDMA2, .port_ops = &ali_20_port_ops }; /* Revision 0xC2 adds UDMA66 */ static const struct ata_port_info info_c2 = { - .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_PIO_LBA48, - .pio_mask = 0x1f, - .mwdma_mask = 0x07, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_PIO_LBA48 | + ATA_FLAG_IGN_SIMPLEX, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA2, .udma_mask = ATA_UDMA4, .port_ops = &ali_c2_port_ops }; /* Revision 0xC3 is UDMA66 for now */ static const struct ata_port_info info_c3 = { - .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_PIO_LBA48, - .pio_mask = 0x1f, - .mwdma_mask = 0x07, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_PIO_LBA48 | + ATA_FLAG_IGN_SIMPLEX, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA2, .udma_mask = ATA_UDMA4, .port_ops = &ali_c2_port_ops }; /* Revision 0xC4 is UDMA100 */ static const struct ata_port_info info_c4 = { - .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_PIO_LBA48, - .pio_mask = 0x1f, - .mwdma_mask = 0x07, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_PIO_LBA48 | + ATA_FLAG_IGN_SIMPLEX, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA2, .udma_mask = ATA_UDMA5, - .port_ops = &ali_c2_port_ops + .port_ops = &ali_c4_port_ops }; /* Revision 0xC5 is UDMA133 with LBA48 DMA */ static const struct ata_port_info info_c5 = { - .flags = ATA_FLAG_SLAVE_POSS, - .pio_mask = 0x1f, - .mwdma_mask = 0x07, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_IGN_SIMPLEX, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA2, .udma_mask = ATA_UDMA6, .port_ops = &ali_c5_port_ops }; const struct ata_port_info *ppi[] = { NULL, NULL }; u8 tmp; - struct pci_dev *isa_bridge; int rc; rc = pcim_enable_device(pdev); @@ -544,21 +576,23 @@ static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id) ali_init_chipset(pdev); - isa_bridge = pci_get_device(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, NULL); - if (isa_bridge && pdev->revision >= 0x20 && pdev->revision < 0xC2) { + if (ali_isa_bridge && pdev->revision >= 0x20 && pdev->revision < 0xC2) { /* Are we paired with a UDMA capable chip */ - pci_read_config_byte(isa_bridge, 0x5E, &tmp); + pci_read_config_byte(ali_isa_bridge, 0x5E, &tmp); if ((tmp & 0x1E) == 0x12) ppi[0] = &info_20_udma; - pci_dev_put(isa_bridge); } - return ata_pci_sff_init_one(pdev, ppi, &ali_sht, NULL); + + if (!ppi[0]->mwdma_mask && !ppi[0]->udma_mask) + return ata_pci_sff_init_one(pdev, ppi, &ali_sht, NULL, 0); + else + return ata_pci_bmdma_init_one(pdev, ppi, &ali_sht, NULL, 0); } -#ifdef CONFIG_PM +#ifdef CONFIG_PM_SLEEP static int ali_reinit_one(struct pci_dev *pdev) { - struct ata_host *host = dev_get_drvdata(&pdev->dev); + struct ata_host *host = pci_get_drvdata(pdev); int rc; rc = ata_pci_device_do_resume(pdev); @@ -582,7 +616,7 @@ static struct pci_driver ali_pci_driver = { .id_table = ali, .probe = ali_init_one, .remove = ata_pci_remove_one, -#ifdef CONFIG_PM +#ifdef CONFIG_PM_SLEEP .suspend = ata_pci_device_suspend, .resume = ali_reinit_one, #endif @@ -590,13 +624,20 @@ static struct pci_driver ali_pci_driver = { static int __init ali_init(void) { - return pci_register_driver(&ali_pci_driver); + int ret; + ali_isa_bridge = pci_get_device(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, NULL); + + ret = pci_register_driver(&ali_pci_driver); + if (ret < 0) + pci_dev_put(ali_isa_bridge); + return ret; } static void __exit ali_exit(void) { pci_unregister_driver(&ali_pci_driver); + pci_dev_put(ali_isa_bridge); } |