171 files changed, 12054 insertions, 5601 deletions

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 3f48e35ee61..2c32c8702cf 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -273,6 +273,14 @@ config ARCH_L7200
 	  If you have any questions or comments about the Linux kernel port
 	  to this board, send e-mail to <sjhill@cotw.com>.
 
+config ARCH_NS9XXX
+	bool "NetSilicon NS9xxx"
+	help
+	  Say Y here if you intend to run this kernel on a NetSilicon NS9xxx
+	  System.
+
+	  <http://www.digi.com/products/microprocessors/index.jsp>
+
 config ARCH_PNX4008
 	bool "Philips Nexperia PNX4008 Mobile"
 	help
@@ -282,6 +290,7 @@ config ARCH_PXA
 	bool "PXA2xx-based"
 	depends on MMU
 	select ARCH_MTD_XIP
+	select GENERIC_TIME
 	help
 	  Support for Intel's PXA2XX processor line.
 
@@ -305,7 +314,7 @@ config ARCH_SA1100
 	  Support for StrongARM 11x0 based boards.
 
 config ARCH_S3C2410
-	bool "Samsung S3C2410, S3C2412, S3C2413, S3C2440, S3C2442"
+	bool "Samsung S3C2410, S3C2412, S3C2413, S3C2440, S3C2442, S3C2443"
 	help
 	  Samsung S3C2410X CPU based systems, such as the Simtec Electronics
 	  BAST (<http://www.simtec.co.uk/products/EB110ITX/>), the IPAQ 1940 or
@@ -365,7 +374,16 @@ source "arch/arm/mach-omap1/Kconfig"
 
 source "arch/arm/mach-omap2/Kconfig"
 
+source "arch/arm/plat-s3c24xx/Kconfig"
+
+if ARCH_S3C2410
+source "arch/arm/mach-s3c2400/Kconfig"
 source "arch/arm/mach-s3c2410/Kconfig"
+source "arch/arm/mach-s3c2412/Kconfig"
+source "arch/arm/mach-s3c2440/Kconfig"
+source "arch/arm/mach-s3c2442/Kconfig"
+source "arch/arm/mach-s3c2443/Kconfig"
+endif
 
 source "arch/arm/mach-lh7a40x/Kconfig"
 
@@ -379,10 +397,12 @@ source "arch/arm/mach-aaec2000/Kconfig"
 
 source "arch/arm/mach-realview/Kconfig"
 
-source "arch/arm/mach-at91rm9200/Kconfig"
+source "arch/arm/mach-at91/Kconfig"
 
 source "arch/arm/mach-netx/Kconfig"
 
+source "arch/arm/mach-ns9xxx/Kconfig"
+
 # Definitions to make life easier
 config ARCH_ACORN
 	bool
@@ -740,6 +760,20 @@ config XIP_PHYS_ADDR
 	  be linked for and stored to.  This address is dependent on your
 	  own flash usage.
 
+config KEXEC
+	bool "Kexec system call (EXPERIMENTAL)"
+	depends on EXPERIMENTAL
+	help
+	  kexec is a system call that implements the ability to shutdown your
+	  current kernel, and to start another kernel.  It is like a reboot
+	  but it is indepedent of the system firmware.   And like a reboot
+	  you can start any kernel with it, not just Linux.
+
+	  It is an ongoing process to be certain the hardware in a machine
+	  is properly shutdown, so do not be surprised if this code does not
+	  initially work for you.  It may help to enable device hotplugging
+	  support.
+
 endmenu
 
 if (ARCH_SA1100 || ARCH_INTEGRATOR || ARCH_OMAP || ARCH_IMX )
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index 000f1100b55..1320418b5d6 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -124,10 +124,12 @@ endif
  machine-$(CONFIG_ARCH_H720X)	   := h720x
  machine-$(CONFIG_ARCH_AAEC2000)   := aaec2000
  machine-$(CONFIG_ARCH_REALVIEW)   := realview
- machine-$(CONFIG_ARCH_AT91)       := at91rm9200
- machine-$(CONFIG_ARCH_EP93XX)     := ep93xx
- machine-$(CONFIG_ARCH_PNX4008)    := pnx4008
- machine-$(CONFIG_ARCH_NETX)       := netx
+ machine-$(CONFIG_ARCH_AT91)	   := at91rm9200
+ machine-$(CONFIG_ARCH_EP93XX)	   := ep93xx
+ machine-$(CONFIG_ARCH_PNX4008)	   := pnx4008
+ machine-$(CONFIG_ARCH_NETX)	   := netx
+ machine-$(CONFIG_ARCH_NS9XXX)	   := ns9xxx
+ textofs-$(CONFIG_ARCH_NS9XXX)	   := 0x00108000
 
 ifeq ($(CONFIG_ARCH_EBSA110),y)
 # This is what happens if you forget the IOCS16 line.
@@ -149,7 +151,7 @@ MACHINE  := arch/arm/mach-$(machine-y)/
 else
 MACHINE  :=
 endif
-  
+
 export	TEXT_OFFSET GZFLAGS MMUEXT
 
 # Do we have FASTFPE?
@@ -161,6 +163,11 @@ endif
 # If we have a machine-specific directory, then include it in the build.
 core-y				+= arch/arm/kernel/ arch/arm/mm/ arch/arm/common/
 core-y				+= $(MACHINE)
+core-$(CONFIG_ARCH_S3C2410)	+= arch/arm/mach-s3c2400/
+core-$(CONFIG_ARCH_S3C2410)	+= arch/arm/mach-s3c2412/
+core-$(CONFIG_ARCH_S3C2410)	+= arch/arm/mach-s3c2440/
+core-$(CONFIG_ARCH_S3C2410)	+= arch/arm/mach-s3c2442/
+core-$(CONFIG_ARCH_S3C2410)	+= arch/arm/mach-s3c2443/
 core-$(CONFIG_FPE_NWFPE)	+= arch/arm/nwfpe/
 core-$(CONFIG_FPE_FASTFPE)	+= $(FASTFPE_OBJ)
 core-$(CONFIG_VFP)		+= arch/arm/vfp/
@@ -168,6 +175,7 @@ core-$(CONFIG_VFP)		+= arch/arm/vfp/
 # If we have a common platform directory, then include it in the build.
 core-$(CONFIG_PLAT_IOP)		+= arch/arm/plat-iop/
 core-$(CONFIG_ARCH_OMAP)	+= arch/arm/plat-omap/
+core-$(CONFIG_PLAT_S3C24XX)		+= arch/arm/plat-s3c24xx/
 
 drivers-$(CONFIG_OPROFILE)      += arch/arm/oprofile/
 drivers-$(CONFIG_ARCH_CLPS7500)	+= drivers/acorn/char/
diff --git a/arch/arm/boot/.gitignore b/arch/arm/boot/.gitignore
new file mode 100644
index 00000000000..171a0853caf
--- /dev/null
+++ b/arch/arm/boot/.gitignore
@@ -0,0 +1,2 @@
+Image
+zImage
diff --git a/arch/arm/boot/compressed/.gitignore b/arch/arm/boot/compressed/.gitignore
new file mode 100644
index 00000000000..aefee20cbf9
--- /dev/null
+++ b/arch/arm/boot/compressed/.gitignore
@@ -0,0 +1 @@
+piggy.gz
diff --git a/arch/arm/common/dmabounce.c b/arch/arm/common/dmabounce.c
index 2e635b814c1..6fbe7722aa4 100644
--- a/arch/arm/common/dmabounce.c
+++ b/arch/arm/common/dmabounce.c
@@ -32,7 +32,6 @@
 
 #include <asm/cacheflush.h>
 
-#undef DEBUG
 #undef STATS
 
 #ifdef STATS
@@ -66,14 +65,13 @@ struct dmabounce_pool {
 };
 
 struct dmabounce_device_info {
-	struct list_head node;
-
 	struct device *dev;
 	struct list_head safe_buffers;
 #ifdef STATS
 	unsigned long total_allocs;
 	unsigned long map_op_count;
 	unsigned long bounce_count;
+	int attr_res;
 #endif
 	struct dmabounce_pool	small;
 	struct dmabounce_pool	large;
@@ -81,33 +79,23 @@ struct dmabounce_device_info {
 	rwlock_t lock;
 };
 
-static LIST_HEAD(dmabounce_devs);
-
 #ifdef STATS
-static void print_alloc_stats(struct dmabounce_device_info *device_info)
+static ssize_t dmabounce_show(struct device *dev, struct device_attribute *attr,
+			      char *buf)
 {
-	printk(KERN_INFO
-		"%s: dmabounce: sbp: %lu, lbp: %lu, other: %lu, total: %lu\n",
-		device_info->dev->bus_id,
-		device_info->small.allocs, device_info->large.allocs,
+	struct dmabounce_device_info *device_info = dev->archdata.dmabounce;
+	return sprintf(buf, "%lu %lu %lu %lu %lu %lu\n",
+		device_info->small.allocs,
+		device_info->large.allocs,
 		device_info->total_allocs - device_info->small.allocs -
 			device_info->large.allocs,
-		device_info->total_allocs);
+		device_info->total_allocs,
+		device_info->map_op_count,
+		device_info->bounce_count);
 }
-#endif
-
-/* find the given device in the dmabounce device list */
-static inline struct dmabounce_device_info *
-find_dmabounce_dev(struct device *dev)
-{
-	struct dmabounce_device_info *d;
 
-	list_for_each_entry(d, &dmabounce_devs, node)
-		if (d->dev == dev)
-			return d;
-
-	return NULL;
-}
+static DEVICE_ATTR(dmabounce_stats, 0400, dmabounce_show, NULL);
+#endif
 
 
 /* allocate a 'safe' buffer and keep track of it */
@@ -162,8 +150,6 @@ alloc_safe_buffer(struct dmabounce_device_info *device_info, void *ptr,
 	if (pool)
 		pool->allocs++;
 	device_info->total_allocs++;
-	if (device_info->total_allocs % 1000 == 0)
-		print_alloc_stats(device_info);
 #endif
 
 	write_lock_irqsave(&device_info->lock, flags);
@@ -218,20 +204,11 @@ free_safe_buffer(struct dmabounce_device_info *device_info, struct safe_buffer *
 
 /* ************************************************** */
 
-#ifdef STATS
-static void print_map_stats(struct dmabounce_device_info *device_info)
-{
-	dev_info(device_info->dev,
-		"dmabounce: map_op_count=%lu, bounce_count=%lu\n",
-		device_info->map_op_count, device_info->bounce_count);
-}
-#endif
-
 static inline dma_addr_t
 map_single(struct device *dev, void *ptr, size_t size,
 		enum dma_data_direction dir)
 {
-	struct dmabounce_device_info *device_info = find_dmabounce_dev(dev);
+	struct dmabounce_device_info *device_info = dev->archdata.dmabounce;
 	dma_addr_t dma_addr;
 	int needs_bounce = 0;
 
@@ -281,10 +258,14 @@ map_single(struct device *dev, void *ptr, size_t size,
 		ptr = buf->safe;
 
 		dma_addr = buf->safe_dma_addr;
+	} else {
+		/*
+		 * We don't need to sync the DMA buffer since
+		 * it was allocated via the coherent allocators.
+		 */
+		consistent_sync(ptr, size, dir);
 	}
 
-	consistent_sync(ptr, size, dir);
-
 	return dma_addr;
 }
 
@@ -292,7 +273,7 @@ static inline void
 unmap_single(struct device *dev, dma_addr_t dma_addr, size_t size,
 		enum dma_data_direction dir)
 {
-	struct dmabounce_device_info *device_info = find_dmabounce_dev(dev);
+	struct dmabounce_device_info *device_info = dev->archdata.dmabounce;
 	struct safe_buffer *buf = NULL;
 
 	/*
@@ -317,12 +298,12 @@ unmap_single(struct device *dev, dma_addr_t dma_addr, size_t size,
 		DO_STATS ( device_info->bounce_count++ );
 
 		if (dir == DMA_FROM_DEVICE || dir == DMA_BIDIRECTIONAL) {
-			unsigned long ptr;
+			void *ptr = buf->ptr;
 
 			dev_dbg(dev,
 				"%s: copy back safe %p to unsafe %p size %d\n",
-				__func__, buf->safe, buf->ptr, size);
-			memcpy(buf->ptr, buf->safe, size);
+				__func__, buf->safe, ptr, size);
+			memcpy(ptr, buf->safe, size);
 
 			/*
 			 * DMA buffers must have the same cache properties
@@ -332,8 +313,8 @@ unmap_single(struct device *dev, dma_addr_t dma_addr, size_t size,
 			 * bidirectional case because we know the cache
 			 * lines will be coherent with the data written.
 			 */
-			ptr = (unsigned long)buf->ptr;
 			dmac_clean_range(ptr, ptr + size);
+			outer_clean_range(__pa(ptr), __pa(ptr) + size);
 		}
 		free_safe_buffer(device_info, buf);
 	}
@@ -343,7 +324,7 @@ static inline void
 sync_single(struct device *dev, dma_addr_t dma_addr, size_t size,
 		enum dma_data_direction dir)
 {
-	struct dmabounce_device_info *device_info = find_dmabounce_dev(dev);
+	struct dmabounce_device_info *device_info = dev->archdata.dmabounce;
 	struct safe_buffer *buf = NULL;
 
 	if (device_info)
@@ -397,7 +378,10 @@ sync_single(struct device *dev, dma_addr_t dma_addr, size_t size,
 		default:
 			BUG();
 		}
-		consistent_sync(buf->safe, size, dir);
+		/*
+		 * No need to sync the safe buffer - it was allocated
+		 * via the coherent allocators.
+		 */
 	} else {
 		consistent_sync(dma_to_virt(dev, dma_addr), size, dir);
 	}
@@ -604,9 +588,10 @@ dmabounce_register_dev(struct device *dev, unsigned long small_buffer_size,
 	device_info->total_allocs = 0;
 	device_info->map_op_count = 0;
 	device_info->bounce_count = 0;
+	device_info->attr_res = device_create_file(dev, &dev_attr_dmabounce_stats);
 #endif
 
-	list_add(&device_info->node, &dmabounce_devs);
+	dev->archdata.dmabounce = device_info;
 
 	printk(KERN_INFO "dmabounce: registered device %s on %s bus\n",
 		dev->bus_id, dev->bus->name);
@@ -623,7 +608,9 @@ dmabounce_register_dev(struct device *dev, unsigned long small_buffer_size,
 void
 dmabounce_unregister_dev(struct device *dev)
 {
-	struct dmabounce_device_info *device_info = find_dmabounce_dev(dev);
+	struct dmabounce_device_info *device_info = dev->archdata.dmabounce;
+
+	dev->archdata.dmabounce = NULL;
 
 	if (!device_info) {
 		printk(KERN_WARNING
@@ -645,12 +632,10 @@ dmabounce_unregister_dev(struct device *dev)
 		dma_pool_destroy(device_info->large.pool);
 
 #ifdef STATS
-	print_alloc_stats(device_info);
-	print_map_stats(device_info);
+	if (device_info->attr_res == 0)
+		device_remove_file(dev, &dev_attr_dmabounce_stats);
 #endif
 
-	list_del(&device_info->node);
-
 	kfree(device_info);
 
 	printk(KERN_INFO "dmabounce: device %s on %s bus unregistered\n",
diff --git a/arch/arm/common/gic.c b/arch/arm/common/gic.c
index 09b9d1b6844..4deece5fbdf 100644
--- a/arch/arm/common/gic.c
+++ b/arch/arm/common/gic.c
@@ -14,7 +14,9 @@
  *
  * o There is one CPU Interface per CPU, which sends interrupts sent
  *   by the Distributor, and interrupts generated locally, to the
- *   associated CPU.
+ *   associated CPU. The base address of the CPU interface is usually
+ *   aliased so that the same address points to different chips depending
+ *   on the CPU it is accessed from.
  *
  * Note that IRQs 0-31 are special - they are local to each CPU.
  * As such, the enable set/clear, pending set/clear and active bit
@@ -31,10 +33,38 @@
 #include <asm/mach/irq.h>
 #include <asm/hardware/gic.h>
 
-static void __iomem *gic_dist_base;
-static void __iomem *gic_cpu_base;
 static DEFINE_SPINLOCK(irq_controller_lock);
 
+struct gic_chip_data {
+	unsigned int irq_offset;
+	void __iomem *dist_base;
+	void __iomem *cpu_base;
+};
+
+#ifndef MAX_GIC_NR
+#define MAX_GIC_NR	1
+#endif
+
+static struct gic_chip_data gic_data[MAX_GIC_NR];
+
+static inline void __iomem *gic_dist_base(unsigned int irq)
+{
+	struct gic_chip_data *gic_data = get_irq_chip_data(irq);
+	return gic_data->dist_base;
+}
+
+static inline void __iomem *gic_cpu_base(unsigned int irq)
+{
+	struct gic_chip_data *gic_data = get_irq_chip_data(irq);
+	return gic_data->cpu_base;
+}
+
+static inline unsigned int gic_irq(unsigned int irq)
+{
+	struct gic_chip_data *gic_data = get_irq_chip_data(irq);
+	return irq - gic_data->irq_offset;
+}
+
 /*
  * Routines to acknowledge, disable and enable interrupts
  *
@@ -55,8 +85,8 @@ static void gic_ack_irq(unsigned int irq)
 	u32 mask = 1 << (irq % 32);
 
 	spin_lock(&irq_controller_lock);
-	writel(mask, gic_dist_base + GIC_DIST_ENABLE_CLEAR + (irq / 32) * 4);
-	writel(irq, gic_cpu_base + GIC_CPU_EOI);
+	writel(mask, gic_dist_base(irq) + GIC_DIST_ENABLE_CLEAR + (gic_irq(irq) / 32) * 4);
+	writel(gic_irq(irq), gic_cpu_base(irq) + GIC_CPU_EOI);
 	spin_unlock(&irq_controller_lock);
 }
 
@@ -65,7 +95,7 @@ static void gic_mask_irq(unsigned int irq)
 	u32 mask = 1 << (irq % 32);
 
 	spin_lock(&irq_controller_lock);
-	writel(mask, gic_dist_base + GIC_DIST_ENABLE_CLEAR + (irq / 32) * 4);
+	writel(mask, gic_dist_base(irq) + GIC_DIST_ENABLE_CLEAR + (gic_irq(irq) / 32) * 4);
 	spin_unlock(&irq_controller_lock);
 }
 
@@ -74,14 +104,14 @@ static void gic_unmask_irq(unsigned int irq)
 	u32 mask = 1 << (irq % 32);
 
 	spin_lock(&irq_controller_lock);
-	writel(mask, gic_dist_base + GIC_DIST_ENABLE_SET + (irq / 32) * 4);
+	writel(mask, gic_dist_base(irq) + GIC_DIST_ENABLE_SET + (gic_irq(irq) / 32) * 4);
 	spin_unlock(&irq_controller_lock);
 }
 
 #ifdef CONFIG_SMP
 static void gic_set_cpu(unsigned int irq, cpumask_t mask_val)
 {
-	void __iomem *reg = gic_dist_base + GIC_DIST_TARGET + (irq & ~3);
+	void __iomem *reg = gic_dist_base(irq) + GIC_DIST_TARGET + (gic_irq(irq) & ~3);
 	unsigned int shift = (irq % 4) * 8;
 	unsigned int cpu = first_cpu(mask_val);
 	u32 val;
@@ -95,6 +125,37 @@ static void gic_set_cpu(unsigned int irq, cpumask_t mask_val)
 }
 #endif
 
+static void fastcall gic_handle_cascade_irq(unsigned int irq,
+					    struct irq_desc *desc)
+{
+	struct gic_chip_data *chip_data = get_irq_data(irq);
+	struct irq_chip *chip = get_irq_chip(irq);
+	unsigned int cascade_irq;
+	unsigned long status;
+
+	/* primary controller ack'ing */
+	chip->ack(irq);
+
+	spin_lock(&irq_controller_lock);
+	status = readl(chip_data->cpu_base + GIC_CPU_INTACK);
+	spin_unlock(&irq_controller_lock);
+
+	cascade_irq = (status & 0x3ff);
+	if (cascade_irq > 1020)
+		goto out;
+	if (cascade_irq < 32 || cascade_irq >= NR_IRQS) {
+		do_bad_IRQ(cascade_irq, desc);
+		goto out;
+	}
+
+	cascade_irq += chip_data->irq_offset;
+	generic_handle_irq(cascade_irq);
+
+ out:
+	/* primary controller unmasking */
+	chip->unmask(irq);
+}
+
 static struct irq_chip gic_chip = {
 	.name		= "GIC",
 	.ack		= gic_ack_irq,
@@ -105,15 +166,29 @@ static struct irq_chip gic_chip = {
 #endif
 };
 
-void __init gic_dist_init(void __iomem *base)
+void __init gic_cascade_irq(unsigned int gic_nr, unsigned int irq)
+{
+	if (gic_nr >= MAX_GIC_NR)
+		BUG();
+	if (set_irq_data(irq, &gic_data[gic_nr]) != 0)
+		BUG();
+	set_irq_chained_handler(irq, gic_handle_cascade_irq);
+}
+
+void __init gic_dist_init(unsigned int gic_nr, void __iomem *base,
+			  unsigned int irq_start)
 {
 	unsigned int max_irq, i;
 	u32 cpumask = 1 << smp_processor_id();
 
+	if (gic_nr >= MAX_GIC_NR)
+		BUG();
+
 	cpumask |= cpumask << 8;
 	cpumask |= cpumask << 16;
 
-	gic_dist_base = base;
+	gic_data[gic_nr].dist_base = base;
+	gic_data[gic_nr].irq_offset = (irq_start - 1) & ~31;
 
 	writel(0, base + GIC_DIST_CTRL);
 
@@ -158,8 +233,9 @@ void __init gic_dist_init(void __iomem *base)
 	/*
 	 * Setup the Linux IRQ subsystem.
 	 */
-	for (i = 29; i < max_irq; i++) {
+	for (i = irq_start; i < gic_data[gic_nr].irq_offset + max_irq; i++) {
 		set_irq_chip(i, &gic_chip);
+		set_irq_chip_data(i, &gic_data[gic_nr]);
 		set_irq_handler(i, handle_level_irq);
 		set_irq_flags(i, IRQF_VALID | IRQF_PROBE);
 	}
@@ -167,9 +243,13 @@ void __init gic_dist_init(void __iomem *base)
 	writel(1, base + GIC_DIST_CTRL);
 }
 
-void __cpuinit gic_cpu_init(void __iomem *base)
+void __cpuinit gic_cpu_init(unsigned int gic_nr, void __iomem *base)
 {
-	gic_cpu_base = base;
+	if (gic_nr >= MAX_GIC_NR)
+		BUG();
+
+	gic_data[gic_nr].cpu_base = base;
+
 	writel(0xf0, base + GIC_CPU_PRIMASK);
 	writel(1, base + GIC_CPU_CTRL);
 }
@@ -179,6 +259,7 @@ void gic_raise_softirq(cpumask_t cpumask, unsigned int irq)
 {
 	unsigned long map = *cpus_addr(cpumask);
 
-	writel(map << 16 | irq, gic_dist_base + GIC_DIST_SOFTINT);
+	/* this always happens on GIC0 */
+	writel(map << 16 | irq, gic_data[0].dist_base + GIC_DIST_SOFTINT);
 }
 #endif
diff --git a/arch/arm/configs/at91sam9263ek_defconfig b/arch/arm/configs/at91sam9263ek_defconfig
new file mode 100644
index 00000000000..c72ab82873d
--- /dev/null
+++ b/arch/arm/configs/at91sam9263ek_defconfig
@@ -0,0 +1,1184 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.20-rc1
+# Mon Jan  8 16:06:54 2007
+#
+CONFIG_ARM=y
+# CONFIG_GENERIC_TIME is not set
+CONFIG_MMU=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+# CONFIG_ARCH_HAS_ILOG2_U32 is not set
+# CONFIG_ARCH_HAS_ILOG2_U64 is not set
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_VECTORS_BASE=0xffff0000
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# Code maturity level options
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+
+#
+# General setup
+#
+CONFIG_LOCALVERSION=""
+# CONFIG_LOCALVERSION_AUTO is not set
+# CONFIG_SWAP is not set
+CONFIG_SYSVIPC=y
+# CONFIG_IPC_NS is not set
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_UTS_NS is not set
+# CONFIG_AUDIT is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_RELAY is not set
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_SYSCTL=y
+# CONFIG_EMBEDDED is not set
+CONFIG_UID16=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_EPOLL=y
+CONFIG_SHMEM=y
+CONFIG_SLAB=y
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_RT_MUTEXES=y
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
+# CONFIG_SLOB is not set
+
+#
+# Loadable module support
+#
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_KMOD=y
+
+#
+# Block layer
+#
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+# CONFIG_IOSCHED_DEADLINE is not set
+# CONFIG_IOSCHED_CFQ is not set
+CONFIG_DEFAULT_AS=y
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="anticipatory"
+
+#
+# System Type
+#
+# CONFIG_ARCH_AAEC2000 is not set
+# CONFIG_ARCH_INTEGRATOR is not set
+# CONFIG_ARCH_REALVIEW is not set
+# CONFIG_ARCH_VERSATILE is not set
+CONFIG_ARCH_AT91=y
+# CONFIG_ARCH_CLPS7500 is not set
+# CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_CO285 is not set
+# CONFIG_ARCH_EBSA110 is not set
+# CONFIG_ARCH_EP93XX is not set
+# CONFIG_ARCH_FOOTBRIDGE is not set
+# CONFIG_ARCH_NETX is not set
+# CONFIG_ARCH_H720X is not set
+# CONFIG_ARCH_IMX is not set
+# CONFIG_ARCH_IOP32X is not set
+# CONFIG_ARCH_IOP33X is not set
+# CONFIG_ARCH_IOP13XX is not set
+# CONFIG_ARCH_IXP4XX is not set
+# CONFIG_ARCH_IXP2000 is not set
+# CONFIG_ARCH_IXP23XX is not set
+# CONFIG_ARCH_L7200 is not set
+# CONFIG_ARCH_PNX4008 is not set
+# CONFIG_ARCH_PXA is not set
+# CONFIG_ARCH_RPC is not set
+# CONFIG_ARCH_SA1100 is not set
+# CONFIG_ARCH_S3C2410 is not set
+# CONFIG_ARCH_SHARK is not set
+# CONFIG_ARCH_LH7A40X is not set
+# CONFIG_ARCH_OMAP is not set
+
+#
+# Atmel AT91 System-on-Chip
+#
+# CONFIG_ARCH_AT91RM9200 is not set
+# CONFIG_ARCH_AT91SAM9260 is not set
+# CONFIG_ARCH_AT91SAM9261 is not set
+CONFIG_ARCH_AT91SAM9263=y
+
+#
+# AT91SAM9263 Board Type
+#
+CONFIG_MACH_AT91SAM9263EK=y
+
+#
+# AT91 Board Options
+#
+CONFIG_MTD_AT91_DATAFLASH_CARD=y
+# CONFIG_MTD_NAND_AT91_BUSWIDTH_16 is not set
+
+#
+# AT91 Feature Selections
+#
+# CONFIG_AT91_PROGRAMMABLE_CLOCKS is not set
+
+#
+# Processor Type
+#
+CONFIG_CPU_32=y
+CONFIG_CPU_ARM926T=y
+CONFIG_CPU_32v5=y
+CONFIG_CPU_ABRT_EV5TJ=y
+CONFIG_CPU_CACHE_VIVT=y
+CONFIG_CPU_COPY_V4WB=y
+CONFIG_CPU_TLB_V4WBI=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
+
+#
+# Processor Features
+#
+# CONFIG_ARM_THUMB is not set
+# CONFIG_CPU_ICACHE_DISABLE is not set
+# CONFIG_CPU_DCACHE_DISABLE is not set
+# CONFIG_CPU_DCACHE_WRITETHROUGH is not set
+# CONFIG_CPU_CACHE_ROUND_ROBIN is not set
+
+#
+# Bus support
+#
+
+#
+# PCCARD (PCMCIA/CardBus) support
+#
+# CONFIG_PCCARD is not set
+
+#
+# Kernel Features
+#
+# CONFIG_PREEMPT is not set
+# CONFIG_NO_IDLE_HZ is not set
+CONFIG_HZ=100
+# CONFIG_AEABI is not set
+# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4096
+# CONFIG_RESOURCES_64BIT is not set
+# CONFIG_LEDS is not set
+CONFIG_ALIGNMENT_TRAP=y
+
+#
+# Boot options
+#
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE="mem=64M console=ttyS0,115200 initrd=0x21100000,3145728 root=/dev/ram0 rw"
+# CONFIG_XIP_KERNEL is not set
+
+#
+# Floating point emulation
+#
+
+#
+# At least one emulation must be selected
+#
+CONFIG_FPE_NWFPE=y
+# CONFIG_FPE_NWFPE_XP is not set
+# CONFIG_FPE_FASTFPE is not set
+# CONFIG_VFP is not set
+
+#
+# Userspace binary formats
+#
+CONFIG_BINFMT_ELF=y
+# CONFIG_BINFMT_AOUT is not set
+# CONFIG_BINFMT_MISC is not set
+# CONFIG_ARTHUR is not set
+
+#
+# Power management options
+#
+# CONFIG_PM is not set
+# CONFIG_APM is not set
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+# CONFIG_NETDEBUG is not set
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+# CONFIG_IP_MULTICAST is not set
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+# CONFIG_IP_PNP_DHCP is not set
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_ARPD is not set
+# CONFIG_SYN_COOKIES is not set
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_DIAG is not set
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_INET6_XFRM_TUNNEL is not set
+# CONFIG_INET6_TUNNEL is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+
+#
+# DCCP Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_DCCP is not set
+
+#
+# SCTP Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_SCTP is not set
+
+#
+# TIPC Configuration (EXPERIMENTAL)
+#
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+
+#
+# QoS and/or fair queueing
+#
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_IEEE80211 is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_SYS_HYPERVISOR is not set
+
+#
+# Connector - unified userspace <-> kernelspace linker
+#
+# CONFIG_CONNECTOR is not set
+
+#
+# Memory Technology Devices (MTD)
+#
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_CONCAT is not set
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_REDBOOT_PARTS is not set
+CONFIG_MTD_CMDLINE_PARTS=y
+# CONFIG_MTD_AFS_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+# CONFIG_MTD_CFI is not set
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+# CONFIG_MTD_OBSOLETE_CHIPS is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+CONFIG_MTD_DATAFLASH=y
+# CONFIG_MTD_M25P80 is not set
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+
+#
+# NAND Flash Device Drivers
+#
+CONFIG_MTD_NAND=y
+# CONFIG_MTD_NAND_VERIFY_WRITE is not set
+# CONFIG_MTD_NAND_ECC_SMC is not set
+CONFIG_MTD_NAND_IDS=y
+# CONFIG_MTD_NAND_DISKONCHIP is not set
+CONFIG_MTD_NAND_AT91=y
+# CONFIG_MTD_NAND_NANDSIM is not set
+
+#
+# OneNAND Flash Device Drivers
+#
+# CONFIG_MTD_ONENAND is not set
+
+#
+# Parallel port support
+#
+# CONFIG_PARPORT is not set
+
+#
+# Plug and Play support
+#
+
+#
+# Block devices
+#
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=y
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_UB is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=8192
+CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
+CONFIG_BLK_DEV_INITRD=y
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+CONFIG_SCSI=y
+# CONFIG_SCSI_TGT is not set
+# CONFIG_SCSI_NETLINK is not set
+CONFIG_SCSI_PROC_FS=y
+
+#
+# SCSI support type (disk, tape, CD-ROM)
+#
+CONFIG_BLK_DEV_SD=y
+# CONFIG_CHR_DEV_ST is not set
+# CONFIG_CHR_DEV_OSST is not set
+# CONFIG_BLK_DEV_SR is not set
+# CONFIG_CHR_DEV_SG is not set
+# CONFIG_CHR_DEV_SCH is not set
+
+#
+# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
+#
+CONFIG_SCSI_MULTI_LUN=y
+# CONFIG_SCSI_CONSTANTS is not set
+# CONFIG_SCSI_LOGGING is not set
+# CONFIG_SCSI_SCAN_ASYNC is not set
+
+#
+# SCSI Transports
+#
+# CONFIG_SCSI_SPI_ATTRS is not set
+# CONFIG_SCSI_FC_ATTRS is not set
+# CONFIG_SCSI_ISCSI_ATTRS is not set
+# CONFIG_SCSI_SAS_ATTRS is not set
+# CONFIG_SCSI_SAS_LIBSAS is not set
+
+#
+# SCSI low-level drivers
+#
+# CONFIG_ISCSI_TCP is not set
+# CONFIG_SCSI_DEBUG is not set
+
+#
+# Serial ATA (prod) and Parallel ATA (experimental) drivers
+#
+# CONFIG_ATA is not set
+
+#
+# Multi-device support (RAID and LVM)
+#
+# CONFIG_MD is not set
+
+#
+# Fusion MPT device support
+#
+# CONFIG_FUSION is not set
+
+#
+# IEEE 1394 (FireWire) support
+#
+
+#
+# I2O device support
+#
+
+#
+# Network device support
+#
+CONFIG_NETDEVICES=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+
+#
+# PHY device support
+#
+# CONFIG_PHYLIB is not set
+
+#
+# Ethernet (10 or 100Mbit)
+#
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_SMC91X is not set
+# CONFIG_DM9000 is not set
+
+#
+# Ethernet (1000 Mbit)
+#
+
+#
+# Ethernet (10000 Mbit)
+#
+
+#
+# Token Ring devices
+#
+
+#
+# Wireless LAN (non-hamradio)
+#
+# CONFIG_NET_RADIO is not set
+
+#
+# Wan interfaces
+#
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_SHAPER is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+
+#
+# ISDN subsystem
+#
+# CONFIG_ISDN is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+
+#
+# Userland interfaces
+#
+CONFIG_INPUT_MOUSEDEV=y
+# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
+CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
+CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
+# CONFIG_INPUT_JOYDEV is not set
+CONFIG_INPUT_TSDEV=y
+CONFIG_INPUT_TSDEV_SCREEN_X=240
+CONFIG_INPUT_TSDEV_SCREEN_Y=320
+CONFIG_INPUT_EVDEV=y
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_INPUT_JOYSTICK is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+CONFIG_TOUCHSCREEN_ADS7846=y
+# CONFIG_TOUCHSCREEN_GUNZE is not set
+# CONFIG_TOUCHSCREEN_ELO is not set
+# CONFIG_TOUCHSCREEN_MTOUCH is not set
+# CONFIG_TOUCHSCREEN_MK712 is not set
+# CONFIG_TOUCHSCREEN_PENMOUNT is not set
+# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set
+# CONFIG_TOUCHSCREEN_TOUCHWIN is not set
+# CONFIG_TOUCHSCREEN_UCB1400 is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+CONFIG_VT=y
+CONFIG_VT_CONSOLE=y
+CONFIG_HW_CONSOLE=y
+# CONFIG_VT_HW_CONSOLE_BINDING is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+CONFIG_SERIAL_ATMEL=y
+CONFIG_SERIAL_ATMEL_CONSOLE=y
+# CONFIG_SERIAL_ATMEL_TTYAT is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_UNIX98_PTYS=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+
+#
+# IPMI
+#
+# CONFIG_IPMI_HANDLER is not set
+
+#
+# Watchdog Cards
+#
+CONFIG_WATCHDOG=y
+CONFIG_WATCHDOG_NOWAYOUT=y
+
+#
+# Watchdog Device Drivers
+#
+# CONFIG_SOFT_WATCHDOG is not set
+
+#
+# USB-based Watchdog Cards
+#
+# CONFIG_USBPCWATCHDOG is not set
+CONFIG_HW_RANDOM=y
+# CONFIG_NVRAM is not set
+# CONFIG_DTLK is not set
+# CONFIG_R3964 is not set
+# CONFIG_RAW_DRIVER is not set
+
+#
+# TPM devices
+#
+# CONFIG_TCG_TPM is not set
+
+#
+# I2C support
+#
+CONFIG_I2C=y
+CONFIG_I2C_CHARDEV=y
+
+#
+# I2C Algorithms
+#
+# CONFIG_I2C_ALGOBIT is not set
+# CONFIG_I2C_ALGOPCF is not set
+# CONFIG_I2C_ALGOPCA is not set
+
+#
+# I2C Hardware Bus support
+#
+CONFIG_I2C_AT91=y
+# CONFIG_I2C_OCORES is not set
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_STUB is not set
+# CONFIG_I2C_PCA is not set
+# CONFIG_I2C_PCA_ISA is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+# CONFIG_SENSORS_DS1337 is not set
+# CONFIG_SENSORS_DS1374 is not set
+# CONFIG_SENSORS_EEPROM is not set
+# CONFIG_SENSORS_PCF8574 is not set
+# CONFIG_SENSORS_PCA9539 is not set
+# CONFIG_SENSORS_PCF8591 is not set
+# CONFIG_SENSORS_MAX6875 is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
+
+#
+# SPI support
+#
+CONFIG_SPI=y
+# CONFIG_SPI_DEBUG is not set
+CONFIG_SPI_MASTER=y
+
+#
+# SPI Master Controller Drivers
+#
+CONFIG_SPI_ATMEL=y
+# CONFIG_SPI_BITBANG is not set
+
+#
+# SPI Protocol Masters
+#
+
+#
+# Dallas's 1-wire bus
+#
+# CONFIG_W1 is not set
+
+#
+# Hardware Monitoring support
+#
+# CONFIG_HWMON is not set
+# CONFIG_HWMON_VID is not set
+
+#
+# Misc devices
+#
+# CONFIG_TIFM_CORE is not set
+
+#
+# LED devices
+#
+# CONFIG_NEW_LEDS is not set
+
+#
+# LED drivers
+#
+
+#
+# LED Triggers
+#
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+
+#
+# Digital Video Broadcasting Devices
+#
+# CONFIG_DVB is not set
+# CONFIG_USB_DABUSB is not set
+
+#
+# Graphics support
+#
+# CONFIG_FIRMWARE_EDID is not set
+CONFIG_FB=y
+# CONFIG_FB_CFB_FILLRECT is not set
+# CONFIG_FB_CFB_COPYAREA is not set
+# CONFIG_FB_CFB_IMAGEBLIT is not set
+# CONFIG_FB_MACMODES is not set
+# CONFIG_FB_BACKLIGHT is not set
+# CONFIG_FB_MODE_HELPERS is not set
+# CONFIG_FB_TILEBLITTING is not set
+# CONFIG_FB_S1D13XXX is not set
+# CONFIG_FB_VIRTUAL is not set
+
+#
+# Console display driver support
+#
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_DUMMY_CONSOLE=y
+# CONFIG_FRAMEBUFFER_CONSOLE is not set
+
+#
+# Logo configuration
+#
+# CONFIG_LOGO is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+
+#
+# HID Devices
+#
+CONFIG_HID=y
+
+#
+# USB support
+#
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+# CONFIG_USB_ARCH_HAS_EHCI is not set
+CONFIG_USB=y
+# CONFIG_USB_DEBUG is not set
+
+#
+# Miscellaneous USB options
+#
+CONFIG_USB_DEVICEFS=y
+# CONFIG_USB_BANDWIDTH is not set
+# CONFIG_USB_DYNAMIC_MINORS is not set
+# CONFIG_USB_MULTITHREAD_PROBE is not set
+# CONFIG_USB_OTG is not set
+
+#
+# USB Host Controller Drivers
+#
+# CONFIG_USB_ISP116X_HCD is not set
+CONFIG_USB_OHCI_HCD=y
+# CONFIG_USB_OHCI_BIG_ENDIAN is not set
+CONFIG_USB_OHCI_LITTLE_ENDIAN=y
+# CONFIG_USB_SL811_HCD is not set
+
+#
+# USB Device Class drivers
+#
+# CONFIG_USB_ACM is not set
+# CONFIG_USB_PRINTER is not set
+
+#
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+#
+
+#
+# may also be needed; see USB_STORAGE Help for more information
+#
+CONFIG_USB_STORAGE=y
+# CONFIG_USB_STORAGE_DEBUG is not set
+# CONFIG_USB_STORAGE_DATAFAB is not set
+# CONFIG_USB_STORAGE_FREECOM is not set
+# CONFIG_USB_STORAGE_DPCM is not set
+# CONFIG_USB_STORAGE_USBAT is not set
+# CONFIG_USB_STORAGE_SDDR09 is not set
+# CONFIG_USB_STORAGE_SDDR55 is not set
+# CONFIG_USB_STORAGE_JUMPSHOT is not set
+# CONFIG_USB_STORAGE_ALAUDA is not set
+# CONFIG_USB_STORAGE_ONETOUCH is not set
+# CONFIG_USB_STORAGE_KARMA is not set
+# CONFIG_USB_LIBUSUAL is not set
+
+#
+# USB Input Devices
+#
+# CONFIG_USB_HID is not set
+
+#
+# USB HID Boot Protocol drivers
+#
+# CONFIG_USB_KBD is not set
+# CONFIG_USB_MOUSE is not set
+# CONFIG_USB_AIPTEK is not set
+# CONFIG_USB_WACOM is not set
+# CONFIG_USB_ACECAD is not set
+# CONFIG_USB_KBTAB is not set
+# CONFIG_USB_POWERMATE is not set
+# CONFIG_USB_TOUCHSCREEN is not set
+# CONFIG_USB_YEALINK is not set
+# CONFIG_USB_XPAD is not set
+# CONFIG_USB_ATI_REMOTE is not set
+# CONFIG_USB_ATI_REMOTE2 is not set
+# CONFIG_USB_KEYSPAN_REMOTE is not set
+# CONFIG_USB_APPLETOUCH is not set
+
+#
+# USB Imaging devices
+#
+# CONFIG_USB_MDC800 is not set
+# CONFIG_USB_MICROTEK is not set
+
+#
+# USB Network Adapters
+#
+# CONFIG_USB_CATC is not set
+# CONFIG_USB_KAWETH is not set
+# CONFIG_USB_PEGASUS is not set
+# CONFIG_USB_RTL8150 is not set
+# CONFIG_USB_USBNET_MII is not set
+# CONFIG_USB_USBNET is not set
+CONFIG_USB_MON=y
+
+#
+# USB port drivers
+#
+
+#
+# USB Serial Converter support
+#
+# CONFIG_USB_SERIAL is not set
+
+#
+# USB Miscellaneous drivers
+#
+# CONFIG_USB_EMI62 is not set
+# CONFIG_USB_EMI26 is not set
+# CONFIG_USB_ADUTUX is not set
+# CONFIG_USB_AUERSWALD is not set
+# CONFIG_USB_RIO500 is not set
+# CONFIG_USB_LEGOTOWER is not set
+# CONFIG_USB_LCD is not set
+# CONFIG_USB_LED is not set
+# CONFIG_USB_CYPRESS_CY7C63 is not set
+# CONFIG_USB_CYTHERM is not set
+# CONFIG_USB_PHIDGET is not set
+# CONFIG_USB_IDMOUSE is not set
+# CONFIG_USB_FTDI_ELAN is not set
+# CONFIG_USB_APPLEDISPLAY is not set
+# CONFIG_USB_LD is not set
+# CONFIG_USB_TRANCEVIBRATOR is not set
+# CONFIG_USB_TEST is not set
+
+#
+# USB DSL modem support
+#
+
+#
+# USB Gadget Support
+#
+CONFIG_USB_GADGET=y
+# CONFIG_USB_GADGET_DEBUG_FILES is not set
+CONFIG_USB_GADGET_SELECTED=y
+# CONFIG_USB_GADGET_NET2280 is not set
+# CONFIG_USB_GADGET_PXA2XX is not set
+# CONFIG_USB_GADGET_GOKU is not set
+# CONFIG_USB_GADGET_LH7A40X is not set
+# CONFIG_USB_GADGET_OMAP is not set
+CONFIG_USB_GADGET_AT91=y
+CONFIG_USB_AT91=y
+# CONFIG_USB_GADGET_DUMMY_HCD is not set
+# CONFIG_USB_GADGET_DUALSPEED is not set
+CONFIG_USB_ZERO=m
+# CONFIG_USB_ETH is not set
+CONFIG_USB_GADGETFS=m
+CONFIG_USB_FILE_STORAGE=m
+# CONFIG_USB_FILE_STORAGE_TEST is not set
+CONFIG_USB_G_SERIAL=m
+# CONFIG_USB_MIDI_GADGET is not set
+
+#
+# MMC/SD Card support
+#
+CONFIG_MMC=y
+# CONFIG_MMC_DEBUG is not set
+CONFIG_MMC_BLOCK=y
+CONFIG_MMC_AT91=m
+# CONFIG_MMC_TIFM_SD is not set
+
+#
+# Real Time Clock
+#
+CONFIG_RTC_LIB=y
+# CONFIG_RTC_CLASS is not set
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
+# CONFIG_EXT3_FS is not set
+# CONFIG_EXT4DEV_FS is not set
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+CONFIG_DNOTIFY=y
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+CONFIG_FAT_FS=y
+# CONFIG_MSDOS_FS is not set
+CONFIG_VFAT_FS=y
+CONFIG_FAT_DEFAULT_CODEPAGE=437
+CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+CONFIG_RAMFS=y
+# CONFIG_CONFIGFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+# CONFIG_JFFS2_SUMMARY is not set
+# CONFIG_JFFS2_FS_XATTR is not set
+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
+CONFIG_JFFS2_ZLIB=y
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
+CONFIG_CRAMFS=y
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+
+#
+# Network File Systems
+#
+CONFIG_NFS_FS=y
+# CONFIG_NFS_V3 is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+# CONFIG_9P_FS is not set
+
+#
+# Partition Types
+#
+# CONFIG_PARTITION_ADVANCED is not set
+CONFIG_MSDOS_PARTITION=y
+
+#
+# Native Language Support
+#
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="iso8859-1"
+CONFIG_NLS_CODEPAGE_437=y
+# CONFIG_NLS_CODEPAGE_737 is not set
+# CONFIG_NLS_CODEPAGE_775 is not set
+CONFIG_NLS_CODEPAGE_850=y
+# CONFIG_NLS_CODEPAGE_852 is not set
+# CONFIG_NLS_CODEPAGE_855 is not set
+# CONFIG_NLS_CODEPAGE_857 is not set
+# CONFIG_NLS_CODEPAGE_860 is not set
+# CONFIG_NLS_CODEPAGE_861 is not set
+# CONFIG_NLS_CODEPAGE_862 is not set
+# CONFIG_NLS_CODEPAGE_863 is not set
+# CONFIG_NLS_CODEPAGE_864 is not set
+# CONFIG_NLS_CODEPAGE_865 is not set
+# CONFIG_NLS_CODEPAGE_866 is not set
+# CONFIG_NLS_CODEPAGE_869 is not set
+# CONFIG_NLS_CODEPAGE_936 is not set
+# CONFIG_NLS_CODEPAGE_950 is not set
+# CONFIG_NLS_CODEPAGE_932 is not set
+# CONFIG_NLS_CODEPAGE_949 is not set
+# CONFIG_NLS_CODEPAGE_874 is not set
+# CONFIG_NLS_ISO8859_8 is not set
+# CONFIG_NLS_CODEPAGE_1250 is not set
+# CONFIG_NLS_CODEPAGE_1251 is not set
+# CONFIG_NLS_ASCII is not set
+CONFIG_NLS_ISO8859_1=y
+# CONFIG_NLS_ISO8859_2 is not set
+# CONFIG_NLS_ISO8859_3 is not set
+# CONFIG_NLS_ISO8859_4 is not set
+# CONFIG_NLS_ISO8859_5 is not set
+# CONFIG_NLS_ISO8859_6 is not set
+# CONFIG_NLS_ISO8859_7 is not set
+# CONFIG_NLS_ISO8859_9 is not set
+# CONFIG_NLS_ISO8859_13 is not set
+# CONFIG_NLS_ISO8859_14 is not set
+# CONFIG_NLS_ISO8859_15 is not set
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_KOI8_U is not set
+# CONFIG_NLS_UTF8 is not set
+
+#
+# Distributed Lock Manager
+#
+# CONFIG_DLM is not set
+
+#
+# Profiling support
+#
+# CONFIG_PROFILING is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_MUST_CHECK=y
+# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_DETECT_SOFTLOCKUP=y
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_RWSEMS is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+CONFIG_DEBUG_BUGVERBOSE=y
+# CONFIG_DEBUG_INFO is not set
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_LIST is not set
+CONFIG_FRAME_POINTER=y
+CONFIG_FORCED_INLINING=y
+# CONFIG_RCU_TORTURE_TEST is not set
+CONFIG_DEBUG_USER=y
+# CONFIG_DEBUG_ERRORS is not set
+CONFIG_DEBUG_LL=y
+# CONFIG_DEBUG_ICEDCC is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+
+#
+# Cryptographic options
+#
+# CONFIG_CRYPTO is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+CONFIG_CRC32=y
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_PLIST=y
+CONFIG_IOMAP_COPY=y
diff --git a/arch/arm/configs/ateb9200_defconfig b/arch/arm/configs/ateb9200_defconfig
index 3de5c643848..baa97698c74 100644
--- a/arch/arm/configs/ateb9200_defconfig
+++ b/arch/arm/configs/ateb9200_defconfig
@@ -1066,7 +1066,7 @@ CONFIG_RTC_INTF_DEV=y
 # CONFIG_RTC_DRV_PCF8563 is not set
 # CONFIG_RTC_DRV_RS5C372 is not set
 # CONFIG_RTC_DRV_M48T86 is not set
-CONFIG_RTC_DRV_AT91=y
+CONFIG_RTC_DRV_AT91RM9200=y
 # CONFIG_RTC_DRV_TEST is not set
 
 #
diff --git a/arch/arm/configs/csb337_defconfig b/arch/arm/configs/csb337_defconfig
index 2cadd51506b..88e5d28aeec 100644
--- a/arch/arm/configs/csb337_defconfig
+++ b/arch/arm/configs/csb337_defconfig
@@ -355,10 +355,12 @@ CONFIG_MTD_CFI_UTIL=y
 # Mapping drivers for chip access
 #
 # CONFIG_MTD_COMPLEX_MAPPINGS is not set
-# CONFIG_MTD_PHYSMAP is not set
+CONFIG_MTD_PHYSMAP=y
+CONFIG_MTD_PHYSMAP_START=0
+CONFIG_MTD_PHYSMAP_LEN=0
+CONFIG_MTD_PHYSMAP_BANKWIDTH=0
 # CONFIG_MTD_ARM_INTEGRATOR is not set
 # CONFIG_MTD_PLATRAM is not set
-CONFIG_MTD_CSB337=y
 
 #
 # Self-contained MTD device drivers
@@ -986,7 +988,7 @@ CONFIG_RTC_DRV_DS1307=y
 # CONFIG_RTC_DRV_PCF8583 is not set
 # CONFIG_RTC_DRV_RS5C372 is not set
 # CONFIG_RTC_DRV_M48T86 is not set
-CONFIG_RTC_DRV_AT91=y
+CONFIG_RTC_DRV_AT91RM9200=y
 # CONFIG_RTC_DRV_TEST is not set
 # CONFIG_RTC_DRV_V3020 is not set
 
diff --git a/arch/arm/configs/csb637_defconfig b/arch/arm/configs/csb637_defconfig
index 94908c1df4c..669f035896f 100644
--- a/arch/arm/configs/csb637_defconfig
+++ b/arch/arm/configs/csb637_defconfig
@@ -355,10 +355,12 @@ CONFIG_MTD_CFI_UTIL=y
 # Mapping drivers for chip access
 #
 # CONFIG_MTD_COMPLEX_MAPPINGS is not set
-# CONFIG_MTD_PHYSMAP is not set
+CONFIG_MTD_PHYSMAP=y
+CONFIG_MTD_PHYSMAP_START=0
+CONFIG_MTD_PHYSMAP_LEN=0
+CONFIG_MTD_PHYSMAP_BANKWIDTH=0
 # CONFIG_MTD_ARM_INTEGRATOR is not set
 # CONFIG_MTD_PLATRAM is not set
-CONFIG_MTD_CSB637=y
 
 #
 # Self-contained MTD device drivers
diff --git a/arch/arm/configs/kafa_defconfig b/arch/arm/configs/kafa_defconfig
index a4cdafc1548..a0f48d54fbc 100644
--- a/arch/arm/configs/kafa_defconfig
+++ b/arch/arm/configs/kafa_defconfig
@@ -718,7 +718,7 @@ CONFIG_RTC_INTF_DEV=y
 # CONFIG_RTC_DRV_PCF8563 is not set
 # CONFIG_RTC_DRV_RS5C372 is not set
 # CONFIG_RTC_DRV_M48T86 is not set
-CONFIG_RTC_DRV_AT91=y
+CONFIG_RTC_DRV_AT91RM9200=y
 # CONFIG_RTC_DRV_TEST is not set
 
 #
diff --git a/arch/arm/configs/ns9xxx_defconfig b/arch/arm/configs/ns9xxx_defconfig
new file mode 100644
index 00000000000..0e5794c6a48
--- /dev/null
+++ b/arch/arm/configs/ns9xxx_defconfig
@@ -0,0 +1,621 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.20
+# Thu Feb 15 20:51:47 2007
+#
+CONFIG_ARM=y
+# CONFIG_GENERIC_TIME is not set
+CONFIG_MMU=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+# CONFIG_ARCH_HAS_ILOG2_U32 is not set
+# CONFIG_ARCH_HAS_ILOG2_U64 is not set
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_VECTORS_BASE=0xffff0000
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# Code maturity level options
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+
+#
+# General setup
+#
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+# CONFIG_IPC_NS is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_UTS_NS is not set
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_RELAY is not set
+CONFIG_INITRAMFS_SOURCE=""
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SYSCTL=y
+CONFIG_EMBEDDED=y
+CONFIG_UID16=y
+# CONFIG_SYSCTL_SYSCALL is not set
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_EPOLL=y
+CONFIG_SHMEM=y
+CONFIG_SLAB=y
+# CONFIG_VM_EVENT_COUNTERS is not set
+CONFIG_RT_MUTEXES=y
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
+# CONFIG_SLOB is not set
+
+#
+# Loadable module support
+#
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+CONFIG_KMOD=y
+
+#
+# Block layer
+#
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+# CONFIG_IOSCHED_AS is not set
+# CONFIG_IOSCHED_DEADLINE is not set
+# CONFIG_IOSCHED_CFQ is not set
+# CONFIG_DEFAULT_AS is not set
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+CONFIG_DEFAULT_NOOP=y
+CONFIG_DEFAULT_IOSCHED="noop"
+
+#
+# System Type
+#
+# CONFIG_ARCH_AAEC2000 is not set
+# CONFIG_ARCH_INTEGRATOR is not set
+# CONFIG_ARCH_REALVIEW is not set
+# CONFIG_ARCH_VERSATILE is not set
+# CONFIG_ARCH_AT91 is not set
+# CONFIG_ARCH_CLPS7500 is not set
+# CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_CO285 is not set
+# CONFIG_ARCH_EBSA110 is not set
+# CONFIG_ARCH_EP93XX is not set
+# CONFIG_ARCH_FOOTBRIDGE is not set
+# CONFIG_ARCH_NETX is not set
+# CONFIG_ARCH_H720X is not set
+# CONFIG_ARCH_IMX is not set
+# CONFIG_ARCH_IOP32X is not set
+# CONFIG_ARCH_IOP33X is not set
+# CONFIG_ARCH_IOP13XX is not set
+# CONFIG_ARCH_IXP4XX is not set
+# CONFIG_ARCH_IXP2000 is not set
+# CONFIG_ARCH_IXP23XX is not set
+# CONFIG_ARCH_L7200 is not set
+CONFIG_ARCH_NS9XXX=y
+# CONFIG_ARCH_PNX4008 is not set
+# CONFIG_ARCH_PXA is not set
+# CONFIG_ARCH_RPC is not set
+# CONFIG_ARCH_SA1100 is not set
+# CONFIG_ARCH_S3C2410 is not set
+# CONFIG_ARCH_SHARK is not set
+# CONFIG_ARCH_LH7A40X is not set
+# CONFIG_ARCH_OMAP is not set
+
+#
+# NS9xxx Implementations
+#
+CONFIG_MACH_CC9P9360DEV=y
+CONFIG_PROCESSOR_NS9360=y
+CONFIG_BOARD_A9M9750DEV=y
+
+#
+# Processor Type
+#
+CONFIG_CPU_32=y
+CONFIG_CPU_ARM926T=y
+CONFIG_CPU_32v5=y
+CONFIG_CPU_ABRT_EV5TJ=y
+CONFIG_CPU_CACHE_VIVT=y
+CONFIG_CPU_COPY_V4WB=y
+CONFIG_CPU_TLB_V4WBI=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
+
+#
+# Processor Features
+#
+# CONFIG_ARM_THUMB is not set
+# CONFIG_CPU_ICACHE_DISABLE is not set
+# CONFIG_CPU_DCACHE_DISABLE is not set
+# CONFIG_CPU_DCACHE_WRITETHROUGH is not set
+# CONFIG_CPU_CACHE_ROUND_ROBIN is not set
+
+#
+# Bus support
+#
+
+#
+# PCCARD (PCMCIA/CardBus) support
+#
+# CONFIG_PCCARD is not set
+
+#
+# Kernel Features
+#
+# CONFIG_PREEMPT is not set
+# CONFIG_NO_IDLE_HZ is not set
+CONFIG_HZ=100
+# CONFIG_AEABI is not set
+# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4096
+# CONFIG_RESOURCES_64BIT is not set
+CONFIG_ALIGNMENT_TRAP=y
+
+#
+# Boot options
+#
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE=""
+# CONFIG_XIP_KERNEL is not set
+
+#
+# Floating point emulation
+#
+
+#
+# At least one emulation must be selected
+#
+CONFIG_FPE_NWFPE=y
+# CONFIG_FPE_NWFPE_XP is not set
+# CONFIG_FPE_FASTFPE is not set
+# CONFIG_VFP is not set
+
+#
+# Userspace binary formats
+#
+CONFIG_BINFMT_ELF=y
+# CONFIG_BINFMT_AOUT is not set
+# CONFIG_BINFMT_MISC is not set
+# CONFIG_ARTHUR is not set
+
+#
+# Power management options
+#
+# CONFIG_PM is not set
+# CONFIG_APM is not set
+
+#
+# Networking
+#
+# CONFIG_NET is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_SYS_HYPERVISOR is not set
+
+#
+# Connector - unified userspace <-> kernelspace linker
+#
+
+#
+# Memory Technology Devices (MTD)
+#
+# CONFIG_MTD is not set
+
+#
+# Parallel port support
+#
+# CONFIG_PARPORT is not set
+
+#
+# Plug and Play support
+#
+
+#
+# Block devices
+#
+# CONFIG_BLK_DEV_COW_COMMON is not set
+# CONFIG_BLK_DEV_LOOP is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=4096
+CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
+CONFIG_BLK_DEV_INITRD=y
+# CONFIG_CDROM_PKTCDVD is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+# CONFIG_SCSI_NETLINK is not set
+
+#
+# Serial ATA (prod) and Parallel ATA (experimental) drivers
+#
+# CONFIG_ATA is not set
+
+#
+# Multi-device support (RAID and LVM)
+#
+# CONFIG_MD is not set
+
+#
+# Fusion MPT device support
+#
+# CONFIG_FUSION is not set
+
+#
+# IEEE 1394 (FireWire) support
+#
+
+#
+# I2O device support
+#
+
+#
+# ISDN subsystem
+#
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+
+#
+# Userland interfaces
+#
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_TSDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TOUCHSCREEN is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+CONFIG_SERIO=y
+# CONFIG_SERIO_SERPORT is not set
+CONFIG_SERIO_LIBPS2=y
+# CONFIG_SERIO_RAW is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+CONFIG_VT=y
+CONFIG_VT_CONSOLE=y
+CONFIG_HW_CONSOLE=y
+# CONFIG_VT_HW_CONSOLE_BINDING is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_RUNTIME_UARTS=4
+CONFIG_SERIAL_8250_EXTENDED=y
+# CONFIG_SERIAL_8250_MANY_PORTS is not set
+# CONFIG_SERIAL_8250_SHARE_IRQ is not set
+# CONFIG_SERIAL_8250_DETECT_IRQ is not set
+# CONFIG_SERIAL_8250_RSA is not set
+
+#
+# Non-8250 serial port support
+#
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_UNIX98_PTYS=y
+# CONFIG_LEGACY_PTYS is not set
+
+#
+# IPMI
+#
+# CONFIG_IPMI_HANDLER is not set
+
+#
+# Watchdog Cards
+#
+# CONFIG_WATCHDOG is not set
+# CONFIG_HW_RANDOM is not set
+# CONFIG_NVRAM is not set
+# CONFIG_DTLK is not set
+# CONFIG_R3964 is not set
+# CONFIG_RAW_DRIVER is not set
+
+#
+# TPM devices
+#
+# CONFIG_TCG_TPM is not set
+
+#
+# I2C support
+#
+# CONFIG_I2C is not set
+
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+
+#
+# Dallas's 1-wire bus
+#
+# CONFIG_W1 is not set
+
+#
+# Hardware Monitoring support
+#
+# CONFIG_HWMON is not set
+# CONFIG_HWMON_VID is not set
+
+#
+# Misc devices
+#
+# CONFIG_TIFM_CORE is not set
+
+#
+# LED devices
+#
+# CONFIG_NEW_LEDS is not set
+
+#
+# LED drivers
+#
+
+#
+# LED Triggers
+#
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+
+#
+# Digital Video Broadcasting Devices
+#
+
+#
+# Graphics support
+#
+# CONFIG_FIRMWARE_EDID is not set
+# CONFIG_FB is not set
+
+#
+# Console display driver support
+#
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_DUMMY_CONSOLE=y
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+
+#
+# HID Devices
+#
+CONFIG_HID=y
+
+#
+# USB support
+#
+CONFIG_USB_ARCH_HAS_HCD=y
+# CONFIG_USB_ARCH_HAS_OHCI is not set
+# CONFIG_USB_ARCH_HAS_EHCI is not set
+# CONFIG_USB is not set
+
+#
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+#
+
+#
+# USB Gadget Support
+#
+# CONFIG_USB_GADGET is not set
+
+#
+# MMC/SD Card support
+#
+# CONFIG_MMC is not set
+
+#
+# Real Time Clock
+#
+CONFIG_RTC_LIB=y
+# CONFIG_RTC_CLASS is not set
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
+# CONFIG_EXT3_FS is not set
+# CONFIG_EXT4DEV_FS is not set
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+# CONFIG_DNOTIFY is not set
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+CONFIG_RAMFS=y
+# CONFIG_CONFIGFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+# CONFIG_CRAMFS is not set
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+
+#
+# Partition Types
+#
+# CONFIG_PARTITION_ADVANCED is not set
+CONFIG_MSDOS_PARTITION=y
+
+#
+# Native Language Support
+#
+# CONFIG_NLS is not set
+
+#
+# Profiling support
+#
+# CONFIG_PROFILING is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+# CONFIG_ENABLE_MUST_CHECK is not set
+# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_DETECT_SOFTLOCKUP is not set
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_RWSEMS is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+CONFIG_DEBUG_BUGVERBOSE=y
+CONFIG_DEBUG_INFO=y
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_LIST is not set
+CONFIG_FRAME_POINTER=y
+CONFIG_FORCED_INLINING=y
+# CONFIG_RCU_TORTURE_TEST is not set
+CONFIG_DEBUG_USER=y
+CONFIG_DEBUG_ERRORS=y
+CONFIG_DEBUG_LL=y
+CONFIG_DEBUG_ICEDCC=y
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+
+#
+# Cryptographic options
+#
+# CONFIG_CRYPTO is not set
+
+#
+# Library routines
+#
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC32 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_PLIST=y
+CONFIG_IOMAP_COPY=y
diff --git a/arch/arm/configs/s3c2410_defconfig b/arch/arm/configs/s3c2410_defconfig
index 3b31a33d008..df19e363203 100644
--- a/arch/arm/configs/s3c2410_defconfig
+++ b/arch/arm/configs/s3c2410_defconfig
@@ -1,7 +1,7 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.19-rc4
-# Fri Nov  3 17:41:31 2006
+# Linux kernel version: 2.6.20
+# Thu Feb 15 11:26:24 2007
 #
 CONFIG_ARM=y
 # CONFIG_GENERIC_TIME is not set
@@ -11,6 +11,8 @@ CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_HARDIRQS_SW_RESEND=y
 CONFIG_GENERIC_IRQ_PROBE=y
 CONFIG_RWSEM_GENERIC_SPINLOCK=y
+# CONFIG_ARCH_HAS_ILOG2_U32 is not set
+# CONFIG_ARCH_HAS_ILOG2_U64 is not set
 CONFIG_GENERIC_HWEIGHT=y
 CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_VECTORS_BASE=0xffff0000
@@ -37,13 +39,14 @@ CONFIG_SYSVIPC=y
 # CONFIG_UTS_NS is not set
 # CONFIG_AUDIT is not set
 # CONFIG_IKCONFIG is not set
+CONFIG_SYSFS_DEPRECATED=y
 # CONFIG_RELAY is not set
 CONFIG_INITRAMFS_SOURCE=""
 CONFIG_CC_OPTIMIZE_FOR_SIZE=y
 CONFIG_SYSCTL=y
 # CONFIG_EMBEDDED is not set
 CONFIG_UID16=y
-# CONFIG_SYSCTL_SYSCALL is not set
+CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
 # CONFIG_KALLSYMS_ALL is not set
 # CONFIG_KALLSYMS_EXTRA_PASS is not set
@@ -76,7 +79,9 @@ CONFIG_KMOD=y
 # Block layer
 #
 CONFIG_BLOCK=y
+# CONFIG_LBD is not set
 # CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
 
 #
 # IO Schedulers
@@ -110,6 +115,7 @@ CONFIG_DEFAULT_IOSCHED="anticipatory"
 # CONFIG_ARCH_IMX is not set
 # CONFIG_ARCH_IOP32X is not set
 # CONFIG_ARCH_IOP33X is not set
+# CONFIG_ARCH_IOP13XX is not set
 # CONFIG_ARCH_IXP4XX is not set
 # CONFIG_ARCH_IXP2000 is not set
 # CONFIG_ARCH_IXP23XX is not set
@@ -122,54 +128,73 @@ CONFIG_ARCH_S3C2410=y
 # CONFIG_ARCH_SHARK is not set
 # CONFIG_ARCH_LH7A40X is not set
 # CONFIG_ARCH_OMAP is not set
+CONFIG_PLAT_S3C24XX=y
+CONFIG_CPU_S3C244X=y
+CONFIG_PM_SIMTEC=y
+# CONFIG_S3C2410_BOOT_WATCHDOG is not set
+# CONFIG_S3C2410_BOOT_ERROR_RESET is not set
+# CONFIG_S3C2410_PM_DEBUG is not set
+# CONFIG_S3C2410_PM_CHECK is not set
+CONFIG_S3C2410_LOWLEVEL_UART_PORT=0
+CONFIG_S3C2410_DMA=y
+# CONFIG_S3C2410_DMA_DEBUG is not set
+CONFIG_MACH_SMDK=y
 
 #
-# S3C24XX Implementations
+# S3C2400 Machines
 #
-# CONFIG_MACH_AML_M5900 is not set
-CONFIG_MACH_ANUBIS=y
-CONFIG_MACH_OSIRIS=y
-CONFIG_ARCH_BAST=y
-CONFIG_BAST_PC104_IRQ=y
+CONFIG_CPU_S3C2410=y
+CONFIG_CPU_S3C2410_DMA=y
+CONFIG_S3C2410_PM=y
+CONFIG_S3C2410_GPIO=y
+CONFIG_S3C2410_CLOCK=y
+
+#
+# S3C2410 Machines
+#
+CONFIG_ARCH_SMDK2410=y
 CONFIG_ARCH_H1940=y
+CONFIG_PM_H1940=y
 CONFIG_MACH_N30=y
-CONFIG_MACH_SMDK=y
-CONFIG_ARCH_SMDK2410=y
-CONFIG_ARCH_S3C2440=y
-CONFIG_SMDK2440_CPU2440=y
-CONFIG_SMDK2440_CPU2442=y
-CONFIG_MACH_S3C2413=y
-CONFIG_MACH_SMDK2413=y
-CONFIG_MACH_VR1000=y
-CONFIG_MACH_RX3715=y
+CONFIG_ARCH_BAST=y
 CONFIG_MACH_OTOM=y
-CONFIG_MACH_NEXCODER_2440=y
-CONFIG_MACH_VSTMS=y
-CONFIG_S3C2410_CLOCK=y
-CONFIG_S3C2410_PM=y
-CONFIG_CPU_S3C2410_DMA=y
-CONFIG_CPU_S3C2410=y
-CONFIG_S3C2412_PM=y
+CONFIG_MACH_AML_M5900=y
+CONFIG_BAST_PC104_IRQ=y
+CONFIG_MACH_VR1000=y
 CONFIG_CPU_S3C2412=y
-CONFIG_CPU_S3C244X=y
+CONFIG_S3C2412_DMA=y
+CONFIG_S3C2412_PM=y
+
+#
+# S3C2412 Machines
+#
+CONFIG_MACH_SMDK2413=y
+CONFIG_MACH_S3C2413=y
+CONFIG_MACH_VSTMS=y
 CONFIG_CPU_S3C2440=y
+CONFIG_S3C2440_DMA=y
+
+#
+# S3C2440 Machines
+#
+CONFIG_MACH_ANUBIS=y
+CONFIG_MACH_OSIRIS=y
+CONFIG_MACH_RX3715=y
+CONFIG_ARCH_S3C2440=y
+CONFIG_MACH_NEXCODER_2440=y
+CONFIG_SMDK2440_CPU2440=y
 CONFIG_CPU_S3C2442=y
 
 #
-# S3C2410 Boot
+# S3C2442 Machines
 #
-# CONFIG_S3C2410_BOOT_WATCHDOG is not set
-# CONFIG_S3C2410_BOOT_ERROR_RESET is not set
+CONFIG_SMDK2440_CPU2442=y
+CONFIG_CPU_S3C2443=y
 
 #
-# S3C2410 Setup
+# S3C2443 Machines
 #
-CONFIG_S3C2410_DMA=y
-# CONFIG_S3C2410_DMA_DEBUG is not set
-# CONFIG_S3C2410_PM_DEBUG is not set
-# CONFIG_S3C2410_PM_CHECK is not set
-CONFIG_PM_SIMTEC=y
-CONFIG_S3C2410_LOWLEVEL_UART_PORT=0
+CONFIG_MACH_SMDK2443=y
 
 #
 # Processor Type
@@ -196,6 +221,7 @@ CONFIG_CPU_CP15_MMU=y
 # CONFIG_CPU_DCACHE_DISABLE is not set
 # CONFIG_CPU_DCACHE_WRITETHROUGH is not set
 # CONFIG_CPU_CACHE_ROUND_ROBIN is not set
+# CONFIG_OUTER_CACHE is not set
 
 #
 # Bus support
@@ -303,6 +329,7 @@ CONFIG_INET_TCP_DIAG=y
 # CONFIG_TCP_CONG_ADVANCED is not set
 CONFIG_TCP_CONG_CUBIC=y
 CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
 # CONFIG_IPV6 is not set
 # CONFIG_INET6_XFRM_TUNNEL is not set
 # CONFIG_INET6_TUNNEL is not set
@@ -385,6 +412,7 @@ CONFIG_MTD_CMDLINE_PARTS=y
 # User Modules And Translation Layers
 #
 CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
 CONFIG_MTD_BLOCK=y
 # CONFIG_FTL is not set
 # CONFIG_NFTL is not set
@@ -531,6 +559,11 @@ CONFIG_BLK_DEV_IDE_BAST=y
 # CONFIG_SCSI_NETLINK is not set
 
 #
+# Serial ATA (prod) and Parallel ATA (experimental) drivers
+#
+# CONFIG_ATA is not set
+
+#
 # Multi-device support (RAID and LVM)
 #
 # CONFIG_MD is not set
@@ -682,7 +715,7 @@ CONFIG_SERIAL_NONSTANDARD=y
 # CONFIG_DIGIEPCA is not set
 # CONFIG_MOXA_INTELLIO is not set
 # CONFIG_MOXA_SMARTIO is not set
-# CONFIG_ISI is not set
+# CONFIG_MOXA_SMARTIO_NEW is not set
 # CONFIG_SYNCLINKMP is not set
 # CONFIG_N_HDLC is not set
 # CONFIG_RISCOM8 is not set
@@ -700,13 +733,14 @@ CONFIG_SERIAL_8250_NR_UARTS=8
 CONFIG_SERIAL_8250_RUNTIME_UARTS=4
 CONFIG_SERIAL_8250_EXTENDED=y
 CONFIG_SERIAL_8250_MANY_PORTS=y
-CONFIG_SERIAL_8250_SHARE_IRQ=y
-# CONFIG_SERIAL_8250_DETECT_IRQ is not set
-# CONFIG_SERIAL_8250_RSA is not set
 # CONFIG_SERIAL_8250_FOURPORT is not set
 # CONFIG_SERIAL_8250_ACCENT is not set
 # CONFIG_SERIAL_8250_BOCA is not set
+# CONFIG_SERIAL_8250_EXAR_ST16C554 is not set
 # CONFIG_SERIAL_8250_HUB6 is not set
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+# CONFIG_SERIAL_8250_DETECT_IRQ is not set
+# CONFIG_SERIAL_8250_RSA is not set
 
 #
 # Non-8250 serial port support
@@ -755,10 +789,6 @@ CONFIG_HW_RANDOM=y
 # CONFIG_NVRAM is not set
 # CONFIG_DTLK is not set
 # CONFIG_R3964 is not set
-
-#
-# Ftape, the floppy tape device driver
-#
 # CONFIG_RAW_DRIVER is not set
 
 #
@@ -863,6 +893,7 @@ CONFIG_SENSORS_LM85=m
 # CONFIG_SENSORS_LM92 is not set
 # CONFIG_SENSORS_MAX1619 is not set
 # CONFIG_SENSORS_PC87360 is not set
+# CONFIG_SENSORS_PC87427 is not set
 # CONFIG_SENSORS_SMSC47M1 is not set
 # CONFIG_SENSORS_SMSC47M192 is not set
 # CONFIG_SENSORS_SMSC47B397 is not set
@@ -870,6 +901,7 @@ CONFIG_SENSORS_LM85=m
 # CONFIG_SENSORS_W83781D is not set
 # CONFIG_SENSORS_W83791D is not set
 # CONFIG_SENSORS_W83792D is not set
+# CONFIG_SENSORS_W83793 is not set
 # CONFIG_SENSORS_W83L785TS is not set
 # CONFIG_SENSORS_W83627HF is not set
 # CONFIG_SENSORS_W83627EHF is not set
@@ -952,6 +984,11 @@ CONFIG_FONT_8x16=y
 # CONFIG_SOUND is not set
 
 #
+# HID Devices
+#
+CONFIG_HID=y
+
+#
 # USB support
 #
 CONFIG_USB_ARCH_HAS_HCD=y
@@ -1028,6 +1065,7 @@ CONFIG_USB_OHCI_LITTLE_ENDIAN=y
 # CONFIG_USB_KAWETH is not set
 # CONFIG_USB_PEGASUS is not set
 # CONFIG_USB_RTL8150 is not set
+# CONFIG_USB_USBNET_MII is not set
 # CONFIG_USB_USBNET is not set
 CONFIG_USB_MON=y
 
@@ -1179,9 +1217,6 @@ CONFIG_RAMFS=y
 # CONFIG_BEFS_FS is not set
 # CONFIG_BFS_FS is not set
 # CONFIG_EFS_FS is not set
-CONFIG_JFFS_FS=y
-CONFIG_JFFS_FS_VERBOSE=0
-# CONFIG_JFFS_PROC_FS is not set
 CONFIG_JFFS2_FS=y
 CONFIG_JFFS2_FS_DEBUG=0
 CONFIG_JFFS2_FS_WRITEBUFFER=y
@@ -1191,7 +1226,7 @@ CONFIG_JFFS2_FS_WRITEBUFFER=y
 CONFIG_JFFS2_ZLIB=y
 CONFIG_JFFS2_RTIME=y
 # CONFIG_JFFS2_RUBIN is not set
-# CONFIG_CRAMFS is not set
+CONFIG_CRAMFS=y
 # CONFIG_VXFS_FS is not set
 # CONFIG_HPFS_FS is not set
 # CONFIG_QNX4FS_FS is not set
@@ -1285,6 +1320,11 @@ CONFIG_NLS_DEFAULT="iso8859-1"
 # CONFIG_NLS_UTF8 is not set
 
 #
+# Distributed Lock Manager
+#
+# CONFIG_DLM is not set
+
+#
 # Profiling support
 #
 # CONFIG_PROFILING is not set
@@ -1296,6 +1336,8 @@ CONFIG_NLS_DEFAULT="iso8859-1"
 CONFIG_ENABLE_MUST_CHECK=y
 CONFIG_MAGIC_SYSRQ=y
 # CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
 CONFIG_DEBUG_KERNEL=y
 CONFIG_LOG_BUF_SHIFT=16
 CONFIG_DETECT_SOFTLOCKUP=y
@@ -1311,12 +1353,10 @@ CONFIG_DEBUG_MUTEXES=y
 # CONFIG_DEBUG_KOBJECT is not set
 CONFIG_DEBUG_BUGVERBOSE=y
 CONFIG_DEBUG_INFO=y
-# CONFIG_DEBUG_FS is not set
 # CONFIG_DEBUG_VM is not set
 # CONFIG_DEBUG_LIST is not set
 CONFIG_FRAME_POINTER=y
 CONFIG_FORCED_INLINING=y
-# CONFIG_HEADERS_CHECK is not set
 # CONFIG_RCU_TORTURE_TEST is not set
 CONFIG_DEBUG_USER=y
 # CONFIG_DEBUG_ERRORS is not set
@@ -1339,6 +1379,7 @@ CONFIG_DEBUG_S3C2410_UART=0
 #
 # Library routines
 #
+CONFIG_BITREVERSE=y
 # CONFIG_CRC_CCITT is not set
 # CONFIG_CRC16 is not set
 CONFIG_CRC32=y
@@ -1346,3 +1387,4 @@ CONFIG_CRC32=y
 CONFIG_ZLIB_INFLATE=y
 CONFIG_ZLIB_DEFLATE=y
 CONFIG_PLIST=y
+CONFIG_IOMAP_COPY=y
diff --git a/arch/arm/kernel/Makefile b/arch/arm/kernel/Makefile
index ab06a86e85d..d5002889773 100644
--- a/arch/arm/kernel/Makefile
+++ b/arch/arm/kernel/Makefile
@@ -19,6 +19,7 @@ obj-$(CONFIG_ARTHUR)		+= arthur.o
 obj-$(CONFIG_ISA_DMA)		+= dma-isa.o
 obj-$(CONFIG_PCI)		+= bios32.o isa.o
 obj-$(CONFIG_SMP)		+= smp.o
+obj-$(CONFIG_KEXEC)		+= machine_kexec.o relocate_kernel.o
 obj-$(CONFIG_OABI_COMPAT)	+= sys_oabi-compat.o
 
 obj-$(CONFIG_CRUNCH)		+= crunch.o crunch-bits.o
diff --git a/arch/arm/kernel/calls.S b/arch/arm/kernel/calls.S
index f7598cbc7ec..ae89cdd82b1 100644
--- a/arch/arm/kernel/calls.S
+++ b/arch/arm/kernel/calls.S
@@ -356,6 +356,7 @@
 		CALL(sys_move_pages)
 /* 345 */	CALL(sys_getcpu)
 		CALL(sys_ni_syscall)		/* eventually epoll_pwait */
+		CALL(sys_kexec_load)
 #ifndef syscalls_counted
 .equ syscalls_padding, ((NR_syscalls + 3) & ~3) - NR_syscalls
 #define syscalls_counted
diff --git a/arch/arm/kernel/crunch.c b/arch/arm/kernel/crunch.c
index cec83783206..627d79414c9 100644
--- a/arch/arm/kernel/crunch.c
+++ b/arch/arm/kernel/crunch.c
@@ -75,6 +75,7 @@ static struct notifier_block crunch_notifier_block = {
 static int __init crunch_init(void)
 {
 	thread_register_notifier(&crunch_notifier_block);
+	elf_hwcap |= HWCAP_CRUNCH;
 
 	return 0;
 }
diff --git a/arch/arm/kernel/ecard.c b/arch/arm/kernel/ecard.c
index 71257e3d513..f1c0fb97417 100644
--- a/arch/arm/kernel/ecard.c
+++ b/arch/arm/kernel/ecard.c
@@ -1009,7 +1009,7 @@ ecard_probe(int slot, card_type_t type)
 		ec->fiqmask = 4;
 	}
 
-	for (i = 0; i < sizeof(blacklist) / sizeof(*blacklist); i++)
+	for (i = 0; i < ARRAY_SIZE(blacklist); i++)
 		if (blacklist[i].manufacturer == ec->cid.manufacturer &&
 		    blacklist[i].product == ec->cid.product) {
 			ec->card_desc = blacklist[i].type;
diff --git a/arch/arm/kernel/machine_kexec.c b/arch/arm/kernel/machine_kexec.c
new file mode 100644
index 00000000000..863c66454f2
--- /dev/null
+++ b/arch/arm/kernel/machine_kexec.c
@@ -0,0 +1,78 @@
+/*
+ * machine_kexec.c - handle transition of Linux booting another kernel
+ */
+
+#include <linux/mm.h>
+#include <linux/kexec.h>
+#include <linux/delay.h>
+#include <linux/reboot.h>
+#include <asm/pgtable.h>
+#include <asm/pgalloc.h>
+#include <asm/mmu_context.h>
+#include <asm/io.h>
+#include <asm/cacheflush.h>
+#include <asm/mach-types.h>
+
+const extern unsigned char relocate_new_kernel[];
+const extern unsigned int relocate_new_kernel_size;
+
+extern void setup_mm_for_reboot(char mode);
+
+extern unsigned long kexec_start_address;
+extern unsigned long kexec_indirection_page;
+extern unsigned long kexec_mach_type;
+
+/*
+ * Provide a dummy crash_notes definition while crash dump arrives to arm.
+ * This prevents breakage of crash_notes attribute in kernel/ksysfs.c.
+ */
+
+int machine_kexec_prepare(struct kimage *image)
+{
+	return 0;
+}
+
+void machine_kexec_cleanup(struct kimage *image)
+{
+}
+
+void machine_shutdown(void)
+{
+}
+
+void machine_crash_shutdown(struct pt_regs *regs)
+{
+}
+
+void machine_kexec(struct kimage *image)
+{
+	unsigned long page_list;
+	unsigned long reboot_code_buffer_phys;
+	void *reboot_code_buffer;
+
+
+	page_list = image->head & PAGE_MASK;
+
+	/* we need both effective and real address here */
+	reboot_code_buffer_phys =
+	    page_to_pfn(image->control_code_page) << PAGE_SHIFT;
+	reboot_code_buffer = page_address(image->control_code_page);
+
+	/* Prepare parameters for reboot_code_buffer*/
+	kexec_start_address = image->start;
+	kexec_indirection_page = page_list;
+	kexec_mach_type = machine_arch_type;
+
+	/* copy our kernel relocation code to the control code page */
+	memcpy(reboot_code_buffer,
+	       relocate_new_kernel, relocate_new_kernel_size);
+
+
+	flush_icache_range((unsigned long) reboot_code_buffer,
+			   (unsigned long) reboot_code_buffer + KEXEC_CONTROL_CODE_SIZE);
+	printk(KERN_INFO "Bye!\n");
+
+	cpu_proc_fin();
+	setup_mm_for_reboot(0); /* mode is not used, so just pass 0*/
+	cpu_reset(reboot_code_buffer_phys);
+}
diff --git a/arch/arm/kernel/relocate_kernel.S b/arch/arm/kernel/relocate_kernel.S
new file mode 100644
index 00000000000..7baadae7cb2
--- /dev/null
+++ b/arch/arm/kernel/relocate_kernel.S
@@ -0,0 +1,74 @@
+/*
+ * relocate_kernel.S - put the kernel image in place to boot
+ */
+
+#include <asm/kexec.h>
+
+	.globl relocate_new_kernel
+relocate_new_kernel:
+
+	ldr	r0,kexec_indirection_page
+	ldr	r1,kexec_start_address
+
+
+0:	/* top, read another word for the indirection page */
+	ldr	r3, [r0],#4
+
+	/* Is it a destination page. Put destination address to r4 */
+	tst	r3,#1,0
+	beq	1f
+	bic	r4,r3,#1
+	b	0b
+1:
+	/* Is it an indirection page */
+	tst	r3,#2,0
+	beq	1f
+	bic	r0,r3,#2
+	b	0b
+1:
+
+	/* are we done ? */
+	tst	r3,#4,0
+	beq	1f
+	b	2f
+
+1:
+	/* is it source ? */
+	tst	r3,#8,0
+	beq	0b
+	bic r3,r3,#8
+	mov r6,#1024
+9:
+	ldr r5,[r3],#4
+	str r5,[r4],#4
+	subs r6,r6,#1
+	bne 9b
+	b 0b
+
+2:
+	/* Jump to relocated kernel */
+	mov lr,r1
+	mov r0,#0
+	ldr r1,kexec_mach_type
+	mov r2,#0
+	mov pc,lr
+
+	.globl kexec_start_address
+kexec_start_address:
+	.long	0x0
+
+	.globl kexec_indirection_page
+kexec_indirection_page:
+	.long	0x0
+
+	.globl kexec_mach_type
+kexec_mach_type:
+	.long	0x0
+
+relocate_new_kernel_end:
+
+	.globl relocate_new_kernel_size
+relocate_new_kernel_size:
+	.long relocate_new_kernel_end - relocate_new_kernel
+
+
diff --git a/arch/arm/kernel/setup.c b/arch/arm/kernel/setup.c
index bbab134cd82..243aea45805 100644
--- a/arch/arm/kernel/setup.c
+++ b/arch/arm/kernel/setup.c
@@ -88,6 +88,9 @@ struct cpu_user_fns cpu_user;
 #ifdef MULTI_CACHE
 struct cpu_cache_fns cpu_cache;
 #endif
+#ifdef CONFIG_OUTER_CACHE
+struct outer_cache_fns outer_cache;
+#endif
 
 struct stack {
 	u32 irq[3];
diff --git a/arch/arm/kernel/time.c b/arch/arm/kernel/time.c
index 3c8cdcfe8d4..3825acd6687 100644
--- a/arch/arm/kernel/time.c
+++ b/arch/arm/kernel/time.c
@@ -40,12 +40,14 @@
  */
 struct sys_timer *system_timer;
 
+#if defined(CONFIG_RTC_DRV_CMOS) || defined(CONFIG_RTC_DRV_CMOS_MODULE)
 /* this needs a better home */
 DEFINE_SPINLOCK(rtc_lock);
 
-#ifdef CONFIG_SA1100_RTC_MODULE
+#ifdef CONFIG_RTC_DRV_CMOS_MODULE
 EXPORT_SYMBOL(rtc_lock);
 #endif
+#endif	/* pc-style 'CMOS' RTC support */
 
 /* change this if you have some constant time drift */
 #define USECS_PER_JIFFY	(1000000/HZ)
diff --git a/arch/arm/mach-at91rm9200/Kconfig b/arch/arm/mach-at91/Kconfig
index 9f11db8af23..bf0d96272e3 100644
--- a/arch/arm/mach-at91rm9200/Kconfig
+++ b/arch/arm/mach-at91/Kconfig
@@ -9,11 +9,14 @@ config ARCH_AT91RM9200
 	bool "AT91RM9200"
 
 config ARCH_AT91SAM9260
-	bool "AT91SAM9260"
+	bool "AT91SAM9260 or AT91SAM9XE"
 
 config ARCH_AT91SAM9261
 	bool "AT91SAM9261"
 
+config ARCH_AT91SAM9263
+	bool "AT91SAM9263"
+
 endchoice
 
 # ----------------------------------------------------------
@@ -90,13 +93,22 @@ endif
 
 if ARCH_AT91SAM9260
 
-comment "AT91SAM9260 Board Type"
+comment "AT91SAM9260 Variants"
+
+config ARCH_AT91SAM9260_SAM9XE
+	bool "AT91SAM9XE"
+	depends on ARCH_AT91SAM9260
+	help
+	  Select this if you are using Atmel's AT91SAM9XE System-on-Chip.
+	  They are basicaly AT91SAM9260s with various sizes of embedded Flash.
+
+comment "AT91SAM9260 / AT91SAM9XE Board Type"
 
 config MACH_AT91SAM9260EK
-	bool "Atmel AT91SAM9260-EK Evaluation Kit"
+	bool "Atmel AT91SAM9260-EK / AT91SAM9XE Evaluation Kit"
 	depends on ARCH_AT91SAM9260
 	help
-	  Select this if you are using Atmel's AT91SAM9260-EK Evaluation Kit.
+	  Select this if you are using Atmel's AT91SAM9260-EK or AT91SAM9XE Evaluation Kit
 	  <http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3933>
 
 endif
@@ -118,17 +130,32 @@ endif
 
 # ----------------------------------------------------------
 
+if ARCH_AT91SAM9263
+
+comment "AT91SAM9263 Board Type"
+
+config MACH_AT91SAM9263EK
+	bool "Atmel AT91SAM9263-EK Evaluation Kit"
+	depends on ARCH_AT91SAM9263
+	help
+	  Select this if you are using Atmel's AT91SAM9263-EK Evaluation Kit.
+	  <http://www.atmel.com/dyn/products/tools_card.asp?tool_id=4057>
+
+endif
+
+# ----------------------------------------------------------
+
 comment "AT91 Board Options"
 
 config MTD_AT91_DATAFLASH_CARD
 	bool "Enable DataFlash Card support"
-	depends on (ARCH_AT91RM9200DK || MACH_AT91RM9200EK || MACH_AT91SAM9260EK || MACH_AT91SAM9261EK)
+	depends on (ARCH_AT91RM9200DK || MACH_AT91RM9200EK || MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK)
 	help
 	  Enable support for the DataFlash card.
 
 config MTD_NAND_AT91_BUSWIDTH_16
 	bool "Enable 16-bit data bus interface to NAND flash"
-	depends on (MACH_AT91SAM9261EK || MACH_AT91SAM9260EK)
+	depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK)
 	help
 	  On AT91SAM926x boards both types of NAND flash can be present
 	  (8 and 16 bit data bus width).
diff --git a/arch/arm/mach-at91rm9200/Makefile b/arch/arm/mach-at91/Makefile
index cf777007847..05de6cdc88f 100644
--- a/arch/arm/mach-at91rm9200/Makefile
+++ b/arch/arm/mach-at91/Makefile
@@ -13,6 +13,7 @@ obj-$(CONFIG_PM)		+= pm.o
 obj-$(CONFIG_ARCH_AT91RM9200)	+= at91rm9200.o at91rm9200_time.o at91rm9200_devices.o
 obj-$(CONFIG_ARCH_AT91SAM9260)	+= at91sam9260.o at91sam926x_time.o at91sam9260_devices.o
 obj-$(CONFIG_ARCH_AT91SAM9261)	+= at91sam9261.o at91sam926x_time.o at91sam9261_devices.o
+obj-$(CONFIG_ARCH_AT91SAM9263)	+= at91sam9263.o at91sam926x_time.o at91sam9263_devices.o
 
 # AT91RM9200 board-specific support
 obj-$(CONFIG_MACH_ONEARM)	+= board-1arm.o
@@ -31,6 +32,9 @@ obj-$(CONFIG_MACH_AT91SAM9260EK) += board-sam9260ek.o
 # AT91SAM9261 board-specific support
 obj-$(CONFIG_MACH_AT91SAM9261EK) += board-sam9261ek.o
 
+# AT91SAM9263 board-specific support
+obj-$(CONFIG_MACH_AT91SAM9263EK) += board-sam9263ek.o
+
 # LEDs support
 led-$(CONFIG_ARCH_AT91RM9200DK)	+= leds.o
 led-$(CONFIG_MACH_AT91RM9200EK)	+= leds.o
diff --git a/arch/arm/mach-at91rm9200/Makefile.boot b/arch/arm/mach-at91/Makefile.boot
index e667dcc7cd3..e667dcc7cd3 100644
--- a/arch/arm/mach-at91rm9200/Makefile.boot
+++ b/arch/arm/mach-at91/Makefile.boot
diff --git a/arch/arm/mach-at91rm9200/at91rm9200.c b/arch/arm/mach-at91/at91rm9200.c
index a92e9a495b0..2ddcdd69df7 100644
--- a/arch/arm/mach-at91rm9200/at91rm9200.c
+++ b/arch/arm/mach-at91/at91rm9200.c
@@ -1,5 +1,5 @@
 /*
- * arch/arm/mach-at91rm9200/at91rm9200.c
+ * arch/arm/mach-at91/at91rm9200.c
  *
  *  Copyright (C) 2005 SAN People
  *
@@ -117,6 +117,36 @@ static struct clk pioD_clk = {
 	.pmc_mask	= 1 << AT91RM9200_ID_PIOD,
 	.type		= CLK_TYPE_PERIPHERAL,
 };
+static struct clk tc0_clk = {
+	.name		= "tc0_clk",
+	.pmc_mask	= 1 << AT91RM9200_ID_TC0,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk tc1_clk = {
+	.name		= "tc1_clk",
+	.pmc_mask	= 1 << AT91RM9200_ID_TC1,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk tc2_clk = {
+	.name		= "tc2_clk",
+	.pmc_mask	= 1 << AT91RM9200_ID_TC2,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk tc3_clk = {
+	.name		= "tc3_clk",
+	.pmc_mask	= 1 << AT91RM9200_ID_TC3,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk tc4_clk = {
+	.name		= "tc4_clk",
+	.pmc_mask	= 1 << AT91RM9200_ID_TC4,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk tc5_clk = {
+	.name		= "tc5_clk",
+	.pmc_mask	= 1 << AT91RM9200_ID_TC5,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
 
 static struct clk *periph_clocks[] __initdata = {
 	&pioA_clk,
@@ -132,7 +162,12 @@ static struct clk *periph_clocks[] __initdata = {
 	&twi_clk,
 	&spi_clk,
 	// ssc 0 .. ssc2
-	// tc0 .. tc5
+	&tc0_clk,
+	&tc1_clk,
+	&tc2_clk,
+	&tc3_clk,
+	&tc4_clk,
+	&tc5_clk,
 	&ohci_clk,
 	&ether_clk,
 	// irq0 .. irq6
diff --git a/arch/arm/mach-at91rm9200/at91rm9200_devices.c b/arch/arm/mach-at91/at91rm9200_devices.c
index 57fac7203fe..2624a4f22d6 100644
--- a/arch/arm/mach-at91rm9200/at91rm9200_devices.c
+++ b/arch/arm/mach-at91/at91rm9200_devices.c
@@ -1,5 +1,5 @@
 /*
- * arch/arm/mach-at91rm9200/at91rm9200_devices.c
+ * arch/arm/mach-at91/at91rm9200_devices.c
  *
  *  Copyright (C) 2005 Thibaut VARENE <varenet@parisc-linux.org>
  *  Copyright (C) 2005 David Brownell
@@ -315,7 +315,7 @@ static struct platform_device at91rm9200_mmc_device = {
 	.num_resources	= ARRAY_SIZE(mmc_resources),
 };
 
-void __init at91_add_device_mmc(struct at91_mmc_data *data)
+void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
 {
 	if (!data)
 		return;
@@ -361,7 +361,7 @@ void __init at91_add_device_mmc(struct at91_mmc_data *data)
 	platform_device_register(&at91rm9200_mmc_device);
 }
 #else
-void __init at91_add_device_mmc(struct at91_mmc_data *data) {}
+void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {}
 #endif
 
 
@@ -594,6 +594,10 @@ u8 at91_leds_timer;
 
 void __init at91_init_leds(u8 cpu_led, u8 timer_led)
 {
+	/* Enable GPIO to access the LEDs */
+	at91_set_gpio_output(cpu_led, 1);
+	at91_set_gpio_output(timer_led, 1);
+
 	at91_leds_cpu	= cpu_led;
 	at91_leds_timer	= timer_led;
 }
diff --git a/arch/arm/mach-at91rm9200/at91rm9200_time.c b/arch/arm/mach-at91/at91rm9200_time.c
index b999e192a7e..949199a244c 100644
--- a/arch/arm/mach-at91rm9200/at91rm9200_time.c
+++ b/arch/arm/mach-at91/at91rm9200_time.c
@@ -1,5 +1,5 @@
 /*
- * linux/arch/arm/mach-at91rm9200/at91rm9200_time.c
+ * linux/arch/arm/mach-at91/at91rm9200_time.c
  *
  *  Copyright (C) 2003 SAN People
  *  Copyright (C) 2003 ATMEL
diff --git a/arch/arm/mach-at91rm9200/at91sam9260.c b/arch/arm/mach-at91/at91sam9260.c
index b14871adc30..6ea41d8266c 100644
--- a/arch/arm/mach-at91rm9200/at91sam9260.c
+++ b/arch/arm/mach-at91/at91sam9260.c
@@ -1,5 +1,5 @@
 /*
- * arch/arm/mach-at91rm9200/at91sam9260.c
+ * arch/arm/mach-at91/at91sam9260.c
  *
  *  Copyright (C) 2006 SAN People
  *
@@ -14,6 +14,7 @@
 
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
+#include <asm/arch/cpu.h>
 #include <asm/arch/at91sam9260.h>
 #include <asm/arch/at91_pmc.h>
 #include <asm/arch/at91_rstc.h>
@@ -27,7 +28,11 @@ static struct map_desc at91sam9260_io_desc[] __initdata = {
 		.pfn		= __phys_to_pfn(AT91_BASE_SYS),
 		.length		= SZ_16K,
 		.type		= MT_DEVICE,
-	}, {
+	}
+};
+
+static struct map_desc at91sam9260_sram_desc[] __initdata = {
+	{
 		.virtual	= AT91_IO_VIRT_BASE - AT91SAM9260_SRAM0_SIZE,
 		.pfn		= __phys_to_pfn(AT91SAM9260_SRAM0_BASE),
 		.length		= AT91SAM9260_SRAM0_SIZE,
@@ -37,7 +42,14 @@ static struct map_desc at91sam9260_io_desc[] __initdata = {
 		.pfn		= __phys_to_pfn(AT91SAM9260_SRAM1_BASE),
 		.length		= AT91SAM9260_SRAM1_SIZE,
 		.type		= MT_DEVICE,
-	},
+	}
+};
+
+static struct map_desc at91sam9xe_sram_desc[] __initdata = {
+	{
+		.pfn		= __phys_to_pfn(AT91SAM9XE_SRAM_BASE),
+		.type		= MT_DEVICE,
+	}
 };
 
 /* --------------------------------------------------------------------
@@ -107,13 +119,28 @@ static struct clk spi1_clk = {
 	.pmc_mask	= 1 << AT91SAM9260_ID_SPI1,
 	.type		= CLK_TYPE_PERIPHERAL,
 };
+static struct clk tc0_clk = {
+	.name		= "tc0_clk",
+	.pmc_mask	= 1 << AT91SAM9260_ID_TC0,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk tc1_clk = {
+	.name		= "tc1_clk",
+	.pmc_mask	= 1 << AT91SAM9260_ID_TC1,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk tc2_clk = {
+	.name		= "tc2_clk",
+	.pmc_mask	= 1 << AT91SAM9260_ID_TC2,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
 static struct clk ohci_clk = {
 	.name		= "ohci_clk",
 	.pmc_mask	= 1 << AT91SAM9260_ID_UHP,
 	.type		= CLK_TYPE_PERIPHERAL,
 };
-static struct clk ether_clk = {
-	.name		= "ether_clk",
+static struct clk macb_clk = {
+	.name		= "macb_clk",
 	.pmc_mask	= 1 << AT91SAM9260_ID_EMAC,
 	.type		= CLK_TYPE_PERIPHERAL,
 };
@@ -137,6 +164,21 @@ static struct clk usart5_clk = {
 	.pmc_mask	= 1 << AT91SAM9260_ID_US5,
 	.type		= CLK_TYPE_PERIPHERAL,
 };
+static struct clk tc3_clk = {
+	.name		= "tc3_clk",
+	.pmc_mask	= 1 << AT91SAM9260_ID_TC3,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk tc4_clk = {
+	.name		= "tc4_clk",
+	.pmc_mask	= 1 << AT91SAM9260_ID_TC4,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk tc5_clk = {
+	.name		= "tc5_clk",
+	.pmc_mask	= 1 << AT91SAM9260_ID_TC5,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
 
 static struct clk *periph_clocks[] __initdata = {
 	&pioA_clk,
@@ -152,14 +194,18 @@ static struct clk *periph_clocks[] __initdata = {
 	&spi0_clk,
 	&spi1_clk,
 	// ssc
-	// tc0 .. tc2
+	&tc0_clk,
+	&tc1_clk,
+	&tc2_clk,
 	&ohci_clk,
-	&ether_clk,
+	&macb_clk,
 	&isi_clk,
 	&usart3_clk,
 	&usart4_clk,
 	&usart5_clk,
-	// tc3 .. tc5
+	&tc3_clk,
+	&tc4_clk,
+	&tc5_clk,
 	// irq0 .. irq2
 };
 
@@ -213,7 +259,7 @@ static struct at91_gpio_bank at91sam9260_gpio[] = {
 
 static void at91sam9260_reset(void)
 {
-	at91_sys_write(AT91_RSTC_CR, (0xA5 << 24) | AT91_RSTC_PROCRST | AT91_RSTC_PERRST);
+	at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_PROCRST | AT91_RSTC_PERRST);
 }
 
 
@@ -221,11 +267,37 @@ static void at91sam9260_reset(void)
  *  AT91SAM9260 processor initialization
  * -------------------------------------------------------------------- */
 
+static void __init at91sam9xe_initialize(void)
+{
+	unsigned long cidr, sram_size;
+
+	cidr = at91_sys_read(AT91_DBGU_CIDR);
+
+	switch (cidr & AT91_CIDR_SRAMSIZ) {
+		case AT91_CIDR_SRAMSIZ_32K:
+			sram_size = 2 * SZ_16K;
+			break;
+		case AT91_CIDR_SRAMSIZ_16K:
+		default:
+			sram_size = SZ_16K;
+	}
+
+	at91sam9xe_sram_desc->virtual = AT91_IO_VIRT_BASE - sram_size;
+	at91sam9xe_sram_desc->length = sram_size;
+
+	iotable_init(at91sam9xe_sram_desc, ARRAY_SIZE(at91sam9xe_sram_desc));
+}
+
 void __init at91sam9260_initialize(unsigned long main_clock)
 {
 	/* Map peripherals */
 	iotable_init(at91sam9260_io_desc, ARRAY_SIZE(at91sam9260_io_desc));
 
+	if (cpu_is_at91sam9xe())
+		at91sam9xe_initialize();
+	else
+		iotable_init(at91sam9260_sram_desc, ARRAY_SIZE(at91sam9260_sram_desc));
+
 	at91_arch_reset = at91sam9260_reset;
 	at91_extern_irq = (1 << AT91SAM9260_ID_IRQ0) | (1 << AT91SAM9260_ID_IRQ1)
 			| (1 << AT91SAM9260_ID_IRQ2);
diff --git a/arch/arm/mach-at91rm9200/at91sam9260_devices.c b/arch/arm/mach-at91/at91sam9260_devices.c
index f42d3a40ec3..f7d342ccbeb 100644
--- a/arch/arm/mach-at91rm9200/at91sam9260_devices.c
+++ b/arch/arm/mach-at91/at91sam9260_devices.c
@@ -1,5 +1,5 @@
 /*
- * arch/arm/mach-at91rm9200/at91sam9260_devices.c
+ * arch/arm/mach-at91/at91sam9260_devices.c
  *
  *  Copyright (C) 2006 Atmel
  *
@@ -128,7 +128,7 @@ void __init at91_add_device_udc(struct at91_udc_data *data) {}
 
 #if defined(CONFIG_MACB) || defined(CONFIG_MACB_MODULE)
 static u64 eth_dmamask = 0xffffffffUL;
-static struct eth_platform_data eth_data;
+static struct at91_eth_data eth_data;
 
 static struct resource eth_resources[] = {
 	[0] = {
@@ -155,7 +155,7 @@ static struct platform_device at91sam9260_eth_device = {
 	.num_resources	= ARRAY_SIZE(eth_resources),
 };
 
-void __init at91_add_device_eth(struct eth_platform_data *data)
+void __init at91_add_device_eth(struct at91_eth_data *data)
 {
 	if (!data)
 		return;
@@ -192,7 +192,7 @@ void __init at91_add_device_eth(struct eth_platform_data *data)
 	platform_device_register(&at91sam9260_eth_device);
 }
 #else
-void __init at91_add_device_eth(struct eth_platform_data *data) {}
+void __init at91_add_device_eth(struct at91_eth_data *data) {}
 #endif
 
 
@@ -229,7 +229,7 @@ static struct platform_device at91sam9260_mmc_device = {
 	.num_resources	= ARRAY_SIZE(mmc_resources),
 };
 
-void __init at91_add_device_mmc(struct at91_mmc_data *data)
+void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
 {
 	if (!data)
 		return;
@@ -275,7 +275,7 @@ void __init at91_add_device_mmc(struct at91_mmc_data *data)
 	platform_device_register(&at91sam9260_mmc_device);
 }
 #else
-void __init at91_add_device_mmc(struct at91_mmc_data *data) {}
+void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {}
 #endif
 
 
@@ -515,6 +515,10 @@ u8 at91_leds_timer;
 
 void __init at91_init_leds(u8 cpu_led, u8 timer_led)
 {
+	/* Enable GPIO to access the LEDs */
+	at91_set_gpio_output(cpu_led, 1);
+	at91_set_gpio_output(timer_led, 1);
+
 	at91_leds_cpu	= cpu_led;
 	at91_leds_timer	= timer_led;
 }
diff --git a/arch/arm/mach-at91rm9200/at91sam9261.c b/arch/arm/mach-at91/at91sam9261.c
index d242bb885c6..784d1e682d6 100644
--- a/arch/arm/mach-at91rm9200/at91sam9261.c
+++ b/arch/arm/mach-at91/at91sam9261.c
@@ -1,5 +1,5 @@
 /*
- * arch/arm/mach-at91rm9200/at91sam9261.c
+ * arch/arm/mach-at91/at91sam9261.c
  *
  *  Copyright (C) 2005 SAN People
  *
@@ -97,6 +97,21 @@ static struct clk spi1_clk = {
 	.pmc_mask	= 1 << AT91SAM9261_ID_SPI1,
 	.type		= CLK_TYPE_PERIPHERAL,
 };
+static struct clk tc0_clk = {
+	.name		= "tc0_clk",
+	.pmc_mask	= 1 << AT91SAM9261_ID_TC0,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk tc1_clk = {
+	.name		= "tc1_clk",
+	.pmc_mask	= 1 << AT91SAM9261_ID_TC1,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk tc2_clk = {
+	.name		= "tc2_clk",
+	.pmc_mask	= 1 << AT91SAM9261_ID_TC2,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
 static struct clk ohci_clk = {
 	.name		= "ohci_clk",
 	.pmc_mask	= 1 << AT91SAM9261_ID_UHP,
@@ -121,7 +136,9 @@ static struct clk *periph_clocks[] __initdata = {
 	&spi0_clk,
 	&spi1_clk,
 	// ssc 0 .. ssc2
-	// tc0 .. tc2
+	&tc0_clk,
+	&tc1_clk,
+	&tc2_clk,
 	&ohci_clk,
 	&lcdc_clk,
 	// irq0 .. irq2
@@ -208,7 +225,7 @@ static struct at91_gpio_bank at91sam9261_gpio[] = {
 
 static void at91sam9261_reset(void)
 {
-	at91_sys_write(AT91_RSTC_CR, (0xA5 << 24) | AT91_RSTC_PROCRST | AT91_RSTC_PERRST);
+	at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_PROCRST | AT91_RSTC_PERRST);
 }
 
 
diff --git a/arch/arm/mach-at91rm9200/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c
index ed1d79081b3..e1504766fd6 100644
--- a/arch/arm/mach-at91rm9200/at91sam9261_devices.c
+++ b/arch/arm/mach-at91/at91sam9261_devices.c
@@ -1,5 +1,5 @@
 /*
- * arch/arm/mach-at91rm9200/at91sam9261_devices.c
+ * arch/arm/mach-at91/at91sam9261_devices.c
  *
  *  Copyright (C) 2005 Thibaut VARENE <varenet@parisc-linux.org>
  *  Copyright (C) 2005 David Brownell
@@ -159,7 +159,7 @@ static struct platform_device at91sam9261_mmc_device = {
 	.num_resources	= ARRAY_SIZE(mmc_resources),
 };
 
-void __init at91_add_device_mmc(struct at91_mmc_data *data)
+void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
 {
 	if (!data)
 		return;
@@ -192,7 +192,7 @@ void __init at91_add_device_mmc(struct at91_mmc_data *data)
 	platform_device_register(&at91sam9261_mmc_device);
 }
 #else
-void __init at91_add_device_mmc(struct at91_mmc_data *data) {}
+void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {}
 #endif
 
 
@@ -513,6 +513,10 @@ u8 at91_leds_timer;
 
 void __init at91_init_leds(u8 cpu_led, u8 timer_led)
 {
+	/* Enable GPIO to access the LEDs */
+	at91_set_gpio_output(cpu_led, 1);
+	at91_set_gpio_output(timer_led, 1);
+
 	at91_leds_cpu	= cpu_led;
 	at91_leds_timer	= timer_led;
 }
diff --git a/arch/arm/mach-at91/at91sam9263.c b/arch/arm/mach-at91/at91sam9263.c
new file mode 100644
index 00000000000..6aa342e8f1b
--- /dev/null
+++ b/arch/arm/mach-at91/at91sam9263.c
@@ -0,0 +1,313 @@
+/*
+ * arch/arm/mach-at91/at91sam9263.c
+ *
+ *  Copyright (C) 2007 Atmel Corporation.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ */
+
+#include <linux/module.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/arch/at91sam9263.h>
+#include <asm/arch/at91_pmc.h>
+#include <asm/arch/at91_rstc.h>
+
+#include "generic.h"
+#include "clock.h"
+
+static struct map_desc at91sam9263_io_desc[] __initdata = {
+	{
+		.virtual	= AT91_VA_BASE_SYS,
+		.pfn		= __phys_to_pfn(AT91_BASE_SYS),
+		.length		= SZ_16K,
+		.type		= MT_DEVICE,
+	}, {
+		.virtual	= AT91_IO_VIRT_BASE - AT91SAM9263_SRAM0_SIZE,
+		.pfn		= __phys_to_pfn(AT91SAM9263_SRAM0_BASE),
+		.length		= AT91SAM9263_SRAM0_SIZE,
+		.type		= MT_DEVICE,
+	}, {
+		.virtual	= AT91_IO_VIRT_BASE - AT91SAM9263_SRAM0_SIZE - AT91SAM9263_SRAM1_SIZE,
+		.pfn		= __phys_to_pfn(AT91SAM9263_SRAM1_BASE),
+		.length		= AT91SAM9263_SRAM1_SIZE,
+		.type		= MT_DEVICE,
+	},
+};
+
+/* --------------------------------------------------------------------
+ *  Clocks
+ * -------------------------------------------------------------------- */
+
+/*
+ * The peripheral clocks.
+ */
+static struct clk pioA_clk = {
+	.name		= "pioA_clk",
+	.pmc_mask	= 1 << AT91SAM9263_ID_PIOA,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk pioB_clk = {
+	.name		= "pioB_clk",
+	.pmc_mask	= 1 << AT91SAM9263_ID_PIOB,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk pioCDE_clk = {
+	.name		= "pioCDE_clk",
+	.pmc_mask	= 1 << AT91SAM9263_ID_PIOCDE,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk usart0_clk = {
+	.name		= "usart0_clk",
+	.pmc_mask	= 1 << AT91SAM9263_ID_US0,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk usart1_clk = {
+	.name		= "usart1_clk",
+	.pmc_mask	= 1 << AT91SAM9263_ID_US1,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk usart2_clk = {
+	.name		= "usart2_clk",
+	.pmc_mask	= 1 << AT91SAM9263_ID_US2,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk mmc0_clk = {
+	.name		= "mci0_clk",
+	.pmc_mask	= 1 << AT91SAM9263_ID_MCI0,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk mmc1_clk = {
+	.name		= "mci1_clk",
+	.pmc_mask	= 1 << AT91SAM9263_ID_MCI1,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk twi_clk = {
+	.name		= "twi_clk",
+	.pmc_mask	= 1 << AT91SAM9263_ID_TWI,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk spi0_clk = {
+	.name		= "spi0_clk",
+	.pmc_mask	= 1 << AT91SAM9263_ID_SPI0,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk spi1_clk = {
+	.name		= "spi1_clk",
+	.pmc_mask	= 1 << AT91SAM9263_ID_SPI1,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk tcb_clk = {
+	.name		= "tcb_clk",
+	.pmc_mask	= 1 << AT91SAM9263_ID_TCB,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk macb_clk = {
+	.name		= "macb_clk",
+	.pmc_mask	= 1 << AT91SAM9263_ID_EMAC,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk udc_clk = {
+	.name		= "udc_clk",
+	.pmc_mask	= 1 << AT91SAM9263_ID_UDP,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk isi_clk = {
+	.name		= "isi_clk",
+	.pmc_mask	= 1 << AT91SAM9263_ID_ISI,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk lcdc_clk = {
+	.name		= "lcdc_clk",
+	.pmc_mask	= 1 << AT91SAM9263_ID_ISI,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+static struct clk ohci_clk = {
+	.name		= "ohci_clk",
+	.pmc_mask	= 1 << AT91SAM9263_ID_UHP,
+	.type		= CLK_TYPE_PERIPHERAL,
+};
+
+static struct clk *periph_clocks[] __initdata = {
+	&pioA_clk,
+	&pioB_clk,
+	&pioCDE_clk,
+	&usart0_clk,
+	&usart1_clk,
+	&usart2_clk,
+	&mmc0_clk,
+	&mmc1_clk,
+	// can
+	&twi_clk,
+	&spi0_clk,
+	&spi1_clk,
+	// ssc0 .. ssc1
+	// ac97
+	&tcb_clk,
+	// pwmc
+	&macb_clk,
+	// 2dge
+	&udc_clk,
+	&isi_clk,
+	&lcdc_clk,
+	// dma
+	&ohci_clk,
+	// irq0 .. irq1
+};
+
+/*
+ * The four programmable clocks.
+ * You must configure pin multiplexing to bring these signals out.
+ */
+static struct clk pck0 = {
+	.name		= "pck0",
+	.pmc_mask	= AT91_PMC_PCK0,
+	.type		= CLK_TYPE_PROGRAMMABLE,
+	.id		= 0,
+};
+static struct clk pck1 = {
+	.name		= "pck1",
+	.pmc_mask	= AT91_PMC_PCK1,
+	.type		= CLK_TYPE_PROGRAMMABLE,
+	.id		= 1,
+};
+static struct clk pck2 = {
+	.name		= "pck2",
+	.pmc_mask	= AT91_PMC_PCK2,
+	.type		= CLK_TYPE_PROGRAMMABLE,
+	.id		= 2,
+};
+static struct clk pck3 = {
+	.name		= "pck3",
+	.pmc_mask	= AT91_PMC_PCK3,
+	.type		= CLK_TYPE_PROGRAMMABLE,
+	.id		= 3,
+};
+
+static void __init at91sam9263_register_clocks(void)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(periph_clocks); i++)
+		clk_register(periph_clocks[i]);
+
+	clk_register(&pck0);
+	clk_register(&pck1);
+	clk_register(&pck2);
+	clk_register(&pck3);
+}
+
+/* --------------------------------------------------------------------
+ *  GPIO
+ * -------------------------------------------------------------------- */
+
+static struct at91_gpio_bank at91sam9263_gpio[] = {
+	{
+		.id		= AT91SAM9263_ID_PIOA,
+		.offset		= AT91_PIOA,
+		.clock		= &pioA_clk,
+	}, {
+		.id		= AT91SAM9263_ID_PIOB,
+		.offset		= AT91_PIOB,
+		.clock		= &pioB_clk,
+	}, {
+		.id		= AT91SAM9263_ID_PIOCDE,
+		.offset		= AT91_PIOC,
+		.clock		= &pioCDE_clk,
+	}, {
+		.id		= AT91SAM9263_ID_PIOCDE,
+		.offset		= AT91_PIOD,
+		.clock		= &pioCDE_clk,
+	}, {
+		.id		= AT91SAM9263_ID_PIOCDE,
+		.offset		= AT91_PIOE,
+		.clock		= &pioCDE_clk,
+	}
+};
+
+static void at91sam9263_reset(void)
+{
+	at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_PROCRST | AT91_RSTC_PERRST);
+}
+
+
+/* --------------------------------------------------------------------
+ *  AT91SAM9263 processor initialization
+ * -------------------------------------------------------------------- */
+
+void __init at91sam9263_initialize(unsigned long main_clock)
+{
+	/* Map peripherals */
+	iotable_init(at91sam9263_io_desc, ARRAY_SIZE(at91sam9263_io_desc));
+
+	at91_arch_reset = at91sam9263_reset;
+	at91_extern_irq = (1 << AT91SAM9263_ID_IRQ0) | (1 << AT91SAM9263_ID_IRQ1);
+
+	/* Init clock subsystem */
+	at91_clock_init(main_clock);
+
+	/* Register the processor-specific clocks */
+	at91sam9263_register_clocks();
+
+	/* Register GPIO subsystem */
+	at91_gpio_init(at91sam9263_gpio, 5);
+}
+
+/* --------------------------------------------------------------------
+ *  Interrupt initialization
+ * -------------------------------------------------------------------- */
+
+/*
+ * The default interrupt priority levels (0 = lowest, 7 = highest).
+ */
+static unsigned int at91sam9263_default_irq_priority[NR_AIC_IRQS] __initdata = {
+	7,	/* Advanced Interrupt Controller (FIQ) */
+	7,	/* System Peripherals */
+	0,	/* Parallel IO Controller A */
+	0,	/* Parallel IO Controller B */
+	0,	/* Parallel IO Controller C, D and E */
+	0,
+	0,
+	6,	/* USART 0 */
+	6,	/* USART 1 */
+	6,	/* USART 2 */
+	0,	/* Multimedia Card Interface 0 */
+	0,	/* Multimedia Card Interface 1 */
+	4,	/* CAN */
+	0,	/* Two-Wire Interface */
+	6,	/* Serial Peripheral Interface 0 */
+	6,	/* Serial Peripheral Interface 1 */
+	5,	/* Serial Synchronous Controller 0 */
+	5,	/* Serial Synchronous Controller 1 */
+	6,	/* AC97 Controller */
+	0,	/* Timer Counter 0, 1 and 2 */
+	0,	/* Pulse Width Modulation Controller */
+	3,	/* Ethernet */
+	0,
+	0,	/* 2D Graphic Engine */
+	3,	/* USB Device Port */
+	0,	/* Image Sensor Interface */
+	3,	/* LDC Controller */
+	0,	/* DMA Controller */
+	0,
+	3,	/* USB Host port */
+	0,	/* Advanced Interrupt Controller (IRQ0) */
+	0,	/* Advanced Interrupt Controller (IRQ1) */
+};
+
+void __init at91sam9263_init_interrupts(unsigned int priority[NR_AIC_IRQS])
+{
+	if (!priority)
+		priority = at91sam9263_default_irq_priority;
+
+	/* Initialize the AIC interrupt controller */
+	at91_aic_init(priority);
+
+	/* Enable GPIO interrupts */
+	at91_gpio_irq_setup();
+}
diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c
new file mode 100644
index 00000000000..d9af7ca58bc
--- /dev/null
+++ b/arch/arm/mach-at91/at91sam9263_devices.c
@@ -0,0 +1,818 @@
+/*
+ * arch/arm/mach-at91/at91sam9263_devices.c
+ *
+ *  Copyright (C) 2007 Atmel Corporation.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ */
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+
+#include <linux/platform_device.h>
+
+#include <asm/arch/board.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/at91sam9263.h>
+#include <asm/arch/at91sam926x_mc.h>
+#include <asm/arch/at91sam9263_matrix.h>
+
+#include "generic.h"
+
+#define SZ_512	0x00000200
+#define SZ_256	0x00000100
+#define SZ_16	0x00000010
+
+/* --------------------------------------------------------------------
+ *  USB Host
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+static u64 ohci_dmamask = 0xffffffffUL;
+static struct at91_usbh_data usbh_data;
+
+static struct resource usbh_resources[] = {
+	[0] = {
+		.start	= AT91SAM9263_UHP_BASE,
+		.end	= AT91SAM9263_UHP_BASE + SZ_1M - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9263_ID_UHP,
+		.end	= AT91SAM9263_ID_UHP,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91_usbh_device = {
+	.name		= "at91_ohci",
+	.id		= -1,
+	.dev		= {
+				.dma_mask		= &ohci_dmamask,
+				.coherent_dma_mask	= 0xffffffff,
+				.platform_data		= &usbh_data,
+	},
+	.resource	= usbh_resources,
+	.num_resources	= ARRAY_SIZE(usbh_resources),
+};
+
+void __init at91_add_device_usbh(struct at91_usbh_data *data)
+{
+	int i;
+
+	if (!data)
+		return;
+
+	/* Enable VBus control for UHP ports */
+	for (i = 0; i < data->ports; i++) {
+		if (data->vbus_pin[i])
+			at91_set_gpio_output(data->vbus_pin[i], 0);
+	}
+
+	usbh_data = *data;
+	platform_device_register(&at91_usbh_device);
+}
+#else
+void __init at91_add_device_usbh(struct at91_usbh_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  USB Device (Gadget)
+ * -------------------------------------------------------------------- */
+
+#ifdef CONFIG_USB_GADGET_AT91
+static struct at91_udc_data udc_data;
+
+static struct resource udc_resources[] = {
+	[0] = {
+		.start	= AT91SAM9263_BASE_UDP,
+		.end	= AT91SAM9263_BASE_UDP + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9263_ID_UDP,
+		.end	= AT91SAM9263_ID_UDP,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91_udc_device = {
+	.name		= "at91_udc",
+	.id		= -1,
+	.dev		= {
+				.platform_data		= &udc_data,
+	},
+	.resource	= udc_resources,
+	.num_resources	= ARRAY_SIZE(udc_resources),
+};
+
+void __init at91_add_device_udc(struct at91_udc_data *data)
+{
+	if (!data)
+		return;
+
+	if (data->vbus_pin) {
+		at91_set_gpio_input(data->vbus_pin, 0);
+		at91_set_deglitch(data->vbus_pin, 1);
+	}
+
+	/* Pullup pin is handled internally by USB device peripheral */
+
+	udc_data = *data;
+	platform_device_register(&at91_udc_device);
+}
+#else
+void __init at91_add_device_udc(struct at91_udc_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  Ethernet
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_MACB) || defined(CONFIG_MACB_MODULE)
+static u64 eth_dmamask = 0xffffffffUL;
+static struct at91_eth_data eth_data;
+
+static struct resource eth_resources[] = {
+	[0] = {
+		.start	= AT91SAM9263_BASE_EMAC,
+		.end	= AT91SAM9263_BASE_EMAC + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9263_ID_EMAC,
+		.end	= AT91SAM9263_ID_EMAC,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91sam9263_eth_device = {
+	.name		= "macb",
+	.id		= -1,
+	.dev		= {
+				.dma_mask		= &eth_dmamask,
+				.coherent_dma_mask	= 0xffffffff,
+				.platform_data		= &eth_data,
+	},
+	.resource	= eth_resources,
+	.num_resources	= ARRAY_SIZE(eth_resources),
+};
+
+void __init at91_add_device_eth(struct at91_eth_data *data)
+{
+	if (!data)
+		return;
+
+	if (data->phy_irq_pin) {
+		at91_set_gpio_input(data->phy_irq_pin, 0);
+		at91_set_deglitch(data->phy_irq_pin, 1);
+	}
+
+	/* Pins used for MII and RMII */
+	at91_set_A_periph(AT91_PIN_PE21, 0);	/* ETXCK_EREFCK */
+	at91_set_B_periph(AT91_PIN_PC25, 0);	/* ERXDV */
+	at91_set_A_periph(AT91_PIN_PE25, 0);	/* ERX0 */
+	at91_set_A_periph(AT91_PIN_PE26, 0);	/* ERX1 */
+	at91_set_A_periph(AT91_PIN_PE27, 0);	/* ERXER */
+	at91_set_A_periph(AT91_PIN_PE28, 0);	/* ETXEN */
+	at91_set_A_periph(AT91_PIN_PE23, 0);	/* ETX0 */
+	at91_set_A_periph(AT91_PIN_PE24, 0);	/* ETX1 */
+	at91_set_A_periph(AT91_PIN_PE30, 0);	/* EMDIO */
+	at91_set_A_periph(AT91_PIN_PE29, 0);	/* EMDC */
+
+	if (!data->is_rmii) {
+		at91_set_A_periph(AT91_PIN_PE22, 0);	/* ECRS */
+		at91_set_B_periph(AT91_PIN_PC26, 0);	/* ECOL */
+		at91_set_B_periph(AT91_PIN_PC22, 0);	/* ERX2 */
+		at91_set_B_periph(AT91_PIN_PC23, 0);	/* ERX3 */
+		at91_set_B_periph(AT91_PIN_PC27, 0);	/* ERXCK */
+		at91_set_B_periph(AT91_PIN_PC20, 0);	/* ETX2 */
+		at91_set_B_periph(AT91_PIN_PC21, 0);	/* ETX3 */
+		at91_set_B_periph(AT91_PIN_PC24, 0);	/* ETXER */
+	}
+
+	eth_data = *data;
+	platform_device_register(&at91sam9263_eth_device);
+}
+#else
+void __init at91_add_device_eth(struct at91_eth_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  MMC / SD
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE)
+static u64 mmc_dmamask = 0xffffffffUL;
+static struct at91_mmc_data mmc0_data, mmc1_data;
+
+static struct resource mmc0_resources[] = {
+	[0] = {
+		.start	= AT91SAM9263_BASE_MCI0,
+		.end	= AT91SAM9263_BASE_MCI0 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9263_ID_MCI0,
+		.end	= AT91SAM9263_ID_MCI0,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91sam9263_mmc0_device = {
+	.name		= "at91_mci",
+	.id		= 0,
+	.dev		= {
+				.dma_mask		= &mmc_dmamask,
+				.coherent_dma_mask	= 0xffffffff,
+				.platform_data		= &mmc0_data,
+	},
+	.resource	= mmc0_resources,
+	.num_resources	= ARRAY_SIZE(mmc0_resources),
+};
+
+static struct resource mmc1_resources[] = {
+	[0] = {
+		.start	= AT91SAM9263_BASE_MCI1,
+		.end	= AT91SAM9263_BASE_MCI1 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9263_ID_MCI1,
+		.end	= AT91SAM9263_ID_MCI1,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91sam9263_mmc1_device = {
+	.name		= "at91_mci",
+	.id		= 1,
+	.dev		= {
+				.dma_mask		= &mmc_dmamask,
+				.coherent_dma_mask	= 0xffffffff,
+				.platform_data		= &mmc1_data,
+	},
+	.resource	= mmc1_resources,
+	.num_resources	= ARRAY_SIZE(mmc1_resources),
+};
+
+void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
+{
+	if (!data)
+		return;
+
+	/* input/irq */
+	if (data->det_pin) {
+		at91_set_gpio_input(data->det_pin, 1);
+		at91_set_deglitch(data->det_pin, 1);
+	}
+	if (data->wp_pin)
+		at91_set_gpio_input(data->wp_pin, 1);
+	if (data->vcc_pin)
+		at91_set_gpio_output(data->vcc_pin, 0);
+
+	if (mmc_id == 0) {		/* MCI0 */
+		/* CLK */
+		at91_set_A_periph(AT91_PIN_PA12, 0);
+
+		if (data->slot_b) {
+			/* CMD */
+			at91_set_A_periph(AT91_PIN_PA16, 1);
+
+			/* DAT0, maybe DAT1..DAT3 */
+			at91_set_A_periph(AT91_PIN_PA17, 1);
+			if (data->wire4) {
+				at91_set_A_periph(AT91_PIN_PA18, 1);
+				at91_set_A_periph(AT91_PIN_PA19, 1);
+				at91_set_A_periph(AT91_PIN_PA20, 1);
+			}
+		} else {
+			/* CMD */
+			at91_set_A_periph(AT91_PIN_PA1, 1);
+
+			/* DAT0, maybe DAT1..DAT3 */
+			at91_set_A_periph(AT91_PIN_PA0, 1);
+			if (data->wire4) {
+				at91_set_A_periph(AT91_PIN_PA3, 1);
+				at91_set_A_periph(AT91_PIN_PA4, 1);
+				at91_set_A_periph(AT91_PIN_PA5, 1);
+			}
+		}
+
+		mmc0_data = *data;
+		at91_clock_associate("mci0_clk", &at91sam9263_mmc1_device.dev, "mci_clk");
+		platform_device_register(&at91sam9263_mmc0_device);
+	} else {			/* MCI1 */
+		/* CLK */
+		at91_set_A_periph(AT91_PIN_PA6, 0);
+
+		if (data->slot_b) {
+			/* CMD */
+			at91_set_A_periph(AT91_PIN_PA21, 1);
+
+			/* DAT0, maybe DAT1..DAT3 */
+			at91_set_A_periph(AT91_PIN_PA22, 1);
+			if (data->wire4) {
+				at91_set_A_periph(AT91_PIN_PA23, 1);
+				at91_set_A_periph(AT91_PIN_PA24, 1);
+				at91_set_A_periph(AT91_PIN_PA25, 1);
+			}
+		} else {
+			/* CMD */
+			at91_set_A_periph(AT91_PIN_PA7, 1);
+
+			/* DAT0, maybe DAT1..DAT3 */
+			at91_set_A_periph(AT91_PIN_PA8, 1);
+			if (data->wire4) {
+				at91_set_A_periph(AT91_PIN_PA9, 1);
+				at91_set_A_periph(AT91_PIN_PA10, 1);
+				at91_set_A_periph(AT91_PIN_PA11, 1);
+			}
+		}
+
+		mmc1_data = *data;
+		at91_clock_associate("mci1_clk", &at91sam9263_mmc1_device.dev, "mci_clk");
+		platform_device_register(&at91sam9263_mmc1_device);
+	}
+}
+#else
+void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  NAND / SmartMedia
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_MTD_NAND_AT91) || defined(CONFIG_MTD_NAND_AT91_MODULE)
+static struct at91_nand_data nand_data;
+
+#define NAND_BASE	AT91_CHIPSELECT_3
+
+static struct resource nand_resources[] = {
+	{
+		.start	= NAND_BASE,
+		.end	= NAND_BASE + SZ_256M - 1,
+		.flags	= IORESOURCE_MEM,
+	}
+};
+
+static struct platform_device at91sam9263_nand_device = {
+	.name		= "at91_nand",
+	.id		= -1,
+	.dev		= {
+				.platform_data	= &nand_data,
+	},
+	.resource	= nand_resources,
+	.num_resources	= ARRAY_SIZE(nand_resources),
+};
+
+void __init at91_add_device_nand(struct at91_nand_data *data)
+{
+	unsigned long csa, mode;
+
+	if (!data)
+		return;
+
+	csa = at91_sys_read(AT91_MATRIX_EBI0CSA);
+	at91_sys_write(AT91_MATRIX_EBI0CSA, csa | AT91_MATRIX_EBI0_CS3A_SMC);
+
+	/* set the bus interface characteristics */
+	at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(0) | AT91_SMC_NCS_WRSETUP_(0)
+			| AT91_SMC_NRDSETUP_(0) | AT91_SMC_NCS_RDSETUP_(0));
+
+	at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3)
+			| AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3));
+
+	at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5));
+
+	if (data->bus_width_16)
+		mode = AT91_SMC_DBW_16;
+	else
+		mode = AT91_SMC_DBW_8;
+	at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(2));
+
+	/* enable pin */
+	if (data->enable_pin)
+		at91_set_gpio_output(data->enable_pin, 1);
+
+	/* ready/busy pin */
+	if (data->rdy_pin)
+		at91_set_gpio_input(data->rdy_pin, 1);
+
+	/* card detect pin */
+	if (data->det_pin)
+		at91_set_gpio_input(data->det_pin, 1);
+
+	nand_data = *data;
+	platform_device_register(&at91sam9263_nand_device);
+}
+#else
+void __init at91_add_device_nand(struct at91_nand_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  TWI (i2c)
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_I2C_AT91) || defined(CONFIG_I2C_AT91_MODULE)
+
+static struct resource twi_resources[] = {
+	[0] = {
+		.start	= AT91SAM9263_BASE_TWI,
+		.end	= AT91SAM9263_BASE_TWI + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9263_ID_TWI,
+		.end	= AT91SAM9263_ID_TWI,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91sam9263_twi_device = {
+	.name		= "at91_i2c",
+	.id		= -1,
+	.resource	= twi_resources,
+	.num_resources	= ARRAY_SIZE(twi_resources),
+};
+
+void __init at91_add_device_i2c(void)
+{
+	/* pins used for TWI interface */
+	at91_set_A_periph(AT91_PIN_PB4, 0);		/* TWD */
+	at91_set_multi_drive(AT91_PIN_PB4, 1);
+
+	at91_set_A_periph(AT91_PIN_PB5, 0);		/* TWCK */
+	at91_set_multi_drive(AT91_PIN_PB5, 1);
+
+	platform_device_register(&at91sam9263_twi_device);
+}
+#else
+void __init at91_add_device_i2c(void) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  SPI
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
+static u64 spi_dmamask = 0xffffffffUL;
+
+static struct resource spi0_resources[] = {
+	[0] = {
+		.start	= AT91SAM9263_BASE_SPI0,
+		.end	= AT91SAM9263_BASE_SPI0 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9263_ID_SPI0,
+		.end	= AT91SAM9263_ID_SPI0,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91sam9263_spi0_device = {
+	.name		= "atmel_spi",
+	.id		= 0,
+	.dev		= {
+				.dma_mask		= &spi_dmamask,
+				.coherent_dma_mask	= 0xffffffff,
+	},
+	.resource	= spi0_resources,
+	.num_resources	= ARRAY_SIZE(spi0_resources),
+};
+
+static const unsigned spi0_standard_cs[4] = { AT91_PIN_PA5, AT91_PIN_PA3, AT91_PIN_PA4, AT91_PIN_PB11 };
+
+static struct resource spi1_resources[] = {
+	[0] = {
+		.start	= AT91SAM9263_BASE_SPI1,
+		.end	= AT91SAM9263_BASE_SPI1 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9263_ID_SPI1,
+		.end	= AT91SAM9263_ID_SPI1,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91sam9263_spi1_device = {
+	.name		= "atmel_spi",
+	.id		= 1,
+	.dev		= {
+				.dma_mask		= &spi_dmamask,
+				.coherent_dma_mask	= 0xffffffff,
+	},
+	.resource	= spi1_resources,
+	.num_resources	= ARRAY_SIZE(spi1_resources),
+};
+
+static const unsigned spi1_standard_cs[4] = { AT91_PIN_PB15, AT91_PIN_PB16, AT91_PIN_PB17, AT91_PIN_PB18 };
+
+void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
+{
+	int i;
+	unsigned long cs_pin;
+	short enable_spi0 = 0;
+	short enable_spi1 = 0;
+
+	/* Choose SPI chip-selects */
+	for (i = 0; i < nr_devices; i++) {
+		if (devices[i].controller_data)
+			cs_pin = (unsigned long) devices[i].controller_data;
+		else if (devices[i].bus_num == 0)
+			cs_pin = spi0_standard_cs[devices[i].chip_select];
+		else
+			cs_pin = spi1_standard_cs[devices[i].chip_select];
+
+		if (devices[i].bus_num == 0)
+			enable_spi0 = 1;
+		else
+			enable_spi1 = 1;
+
+		/* enable chip-select pin */
+		at91_set_gpio_output(cs_pin, 1);
+
+		/* pass chip-select pin to driver */
+		devices[i].controller_data = (void *) cs_pin;
+	}
+
+	spi_register_board_info(devices, nr_devices);
+
+	/* Configure SPI bus(es) */
+	if (enable_spi0) {
+		at91_set_B_periph(AT91_PIN_PA0, 0);	/* SPI0_MISO */
+		at91_set_B_periph(AT91_PIN_PA1, 0);	/* SPI0_MOSI */
+		at91_set_B_periph(AT91_PIN_PA2, 0);	/* SPI1_SPCK */
+
+		at91_clock_associate("spi0_clk", &at91sam9263_spi0_device.dev, "spi_clk");
+		platform_device_register(&at91sam9263_spi0_device);
+	}
+	if (enable_spi1) {
+		at91_set_A_periph(AT91_PIN_PB12, 0);	/* SPI1_MISO */
+		at91_set_A_periph(AT91_PIN_PB13, 0);	/* SPI1_MOSI */
+		at91_set_A_periph(AT91_PIN_PB14, 0);	/* SPI1_SPCK */
+
+		at91_clock_associate("spi1_clk", &at91sam9263_spi1_device.dev, "spi_clk");
+		platform_device_register(&at91sam9263_spi1_device);
+	}
+}
+#else
+void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  LEDs
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_LEDS)
+u8 at91_leds_cpu;
+u8 at91_leds_timer;
+
+void __init at91_init_leds(u8 cpu_led, u8 timer_led)
+{
+	/* Enable GPIO to access the LEDs */
+	at91_set_gpio_output(cpu_led, 1);
+	at91_set_gpio_output(timer_led, 1);
+
+	at91_leds_cpu	= cpu_led;
+	at91_leds_timer	= timer_led;
+}
+#else
+void __init at91_init_leds(u8 cpu_led, u8 timer_led) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  UART
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_SERIAL_ATMEL)
+
+static struct resource dbgu_resources[] = {
+	[0] = {
+		.start	= AT91_VA_BASE_SYS + AT91_DBGU,
+		.end	= AT91_VA_BASE_SYS + AT91_DBGU + SZ_512 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91_ID_SYS,
+		.end	= AT91_ID_SYS,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct atmel_uart_data dbgu_data = {
+	.use_dma_tx	= 0,
+	.use_dma_rx	= 0,		/* DBGU not capable of receive DMA */
+	.regs		= (void __iomem *)(AT91_VA_BASE_SYS + AT91_DBGU),
+};
+
+static struct platform_device at91sam9263_dbgu_device = {
+	.name		= "atmel_usart",
+	.id		= 0,
+	.dev		= {
+				.platform_data	= &dbgu_data,
+				.coherent_dma_mask = 0xffffffff,
+	},
+	.resource	= dbgu_resources,
+	.num_resources	= ARRAY_SIZE(dbgu_resources),
+};
+
+static inline void configure_dbgu_pins(void)
+{
+	at91_set_A_periph(AT91_PIN_PC30, 0);		/* DRXD */
+	at91_set_A_periph(AT91_PIN_PC31, 1);		/* DTXD */
+}
+
+static struct resource uart0_resources[] = {
+	[0] = {
+		.start	= AT91SAM9263_BASE_US0,
+		.end	= AT91SAM9263_BASE_US0 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9263_ID_US0,
+		.end	= AT91SAM9263_ID_US0,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct atmel_uart_data uart0_data = {
+	.use_dma_tx	= 1,
+	.use_dma_rx	= 1,
+};
+
+static struct platform_device at91sam9263_uart0_device = {
+	.name		= "atmel_usart",
+	.id		= 1,
+	.dev		= {
+				.platform_data	= &uart0_data,
+				.coherent_dma_mask = 0xffffffff,
+	},
+	.resource	= uart0_resources,
+	.num_resources	= ARRAY_SIZE(uart0_resources),
+};
+
+static inline void configure_usart0_pins(void)
+{
+	at91_set_A_periph(AT91_PIN_PA26, 1);		/* TXD0 */
+	at91_set_A_periph(AT91_PIN_PA27, 0);		/* RXD0 */
+	at91_set_A_periph(AT91_PIN_PA28, 0);		/* RTS0 */
+	at91_set_A_periph(AT91_PIN_PA29, 0);		/* CTS0 */
+}
+
+static struct resource uart1_resources[] = {
+	[0] = {
+		.start	= AT91SAM9263_BASE_US1,
+		.end	= AT91SAM9263_BASE_US1 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9263_ID_US1,
+		.end	= AT91SAM9263_ID_US1,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct atmel_uart_data uart1_data = {
+	.use_dma_tx	= 1,
+	.use_dma_rx	= 1,
+};
+
+static struct platform_device at91sam9263_uart1_device = {
+	.name		= "atmel_usart",
+	.id		= 2,
+	.dev		= {
+				.platform_data	= &uart1_data,
+				.coherent_dma_mask = 0xffffffff,
+	},
+	.resource	= uart1_resources,
+	.num_resources	= ARRAY_SIZE(uart1_resources),
+};
+
+static inline void configure_usart1_pins(void)
+{
+	at91_set_A_periph(AT91_PIN_PD0, 1);		/* TXD1 */
+	at91_set_A_periph(AT91_PIN_PD1, 0);		/* RXD1 */
+	at91_set_B_periph(AT91_PIN_PD7, 0);		/* RTS1 */
+	at91_set_B_periph(AT91_PIN_PD8, 0);		/* CTS1 */
+}
+
+static struct resource uart2_resources[] = {
+	[0] = {
+		.start	= AT91SAM9263_BASE_US2,
+		.end	= AT91SAM9263_BASE_US2 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9263_ID_US2,
+		.end	= AT91SAM9263_ID_US2,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct atmel_uart_data uart2_data = {
+	.use_dma_tx	= 1,
+	.use_dma_rx	= 1,
+};
+
+static struct platform_device at91sam9263_uart2_device = {
+	.name		= "atmel_usart",
+	.id		= 3,
+	.dev		= {
+				.platform_data	= &uart2_data,
+				.coherent_dma_mask = 0xffffffff,
+	},
+	.resource	= uart2_resources,
+	.num_resources	= ARRAY_SIZE(uart2_resources),
+};
+
+static inline void configure_usart2_pins(void)
+{
+	at91_set_A_periph(AT91_PIN_PD2, 1);		/* TXD2 */
+	at91_set_A_periph(AT91_PIN_PD3, 0);		/* RXD2 */
+	at91_set_B_periph(AT91_PIN_PD5, 0);		/* RTS2 */
+	at91_set_B_periph(AT91_PIN_PD6, 0);		/* CTS2 */
+}
+
+struct platform_device *at91_uarts[ATMEL_MAX_UART];	/* the UARTs to use */
+struct platform_device *atmel_default_console_device;	/* the serial console device */
+
+void __init at91_init_serial(struct at91_uart_config *config)
+{
+	int i;
+
+	/* Fill in list of supported UARTs */
+	for (i = 0; i < config->nr_tty; i++) {
+		switch (config->tty_map[i]) {
+			case 0:
+				configure_usart0_pins();
+				at91_uarts[i] = &at91sam9263_uart0_device;
+				at91_clock_associate("usart0_clk", &at91sam9263_uart0_device.dev, "usart");
+				break;
+			case 1:
+				configure_usart1_pins();
+				at91_uarts[i] = &at91sam9263_uart1_device;
+				at91_clock_associate("usart1_clk", &at91sam9263_uart1_device.dev, "usart");
+				break;
+			case 2:
+				configure_usart2_pins();
+				at91_uarts[i] = &at91sam9263_uart2_device;
+				at91_clock_associate("usart2_clk", &at91sam9263_uart2_device.dev, "usart");
+				break;
+			case 3:
+				configure_dbgu_pins();
+				at91_uarts[i] = &at91sam9263_dbgu_device;
+				at91_clock_associate("mck", &at91sam9263_dbgu_device.dev, "usart");
+				break;
+			default:
+				continue;
+		}
+		at91_uarts[i]->id = i;		/* update ID number to mapped ID */
+	}
+
+	/* Set serial console device */
+	if (config->console_tty < ATMEL_MAX_UART)
+		atmel_default_console_device = at91_uarts[config->console_tty];
+	if (!atmel_default_console_device)
+		printk(KERN_INFO "AT91: No default serial console defined.\n");
+}
+
+void __init at91_add_device_serial(void)
+{
+	int i;
+
+	for (i = 0; i < ATMEL_MAX_UART; i++) {
+		if (at91_uarts[i])
+			platform_device_register(at91_uarts[i]);
+	}
+}
+#else
+void __init at91_init_serial(struct at91_uart_config *config) {}
+void __init at91_add_device_serial(void) {}
+#endif
+
+
+/* -------------------------------------------------------------------- */
+/*
+ * These devices are always present and don't need any board-specific
+ * setup.
+ */
+static int __init at91_add_standard_devices(void)
+{
+	return 0;
+}
+
+arch_initcall(at91_add_standard_devices);
diff --git a/arch/arm/mach-at91rm9200/at91sam926x_time.c b/arch/arm/mach-at91/at91sam926x_time.c
index 99df5f6ee42..a4dded27fa1 100644
--- a/arch/arm/mach-at91rm9200/at91sam926x_time.c
+++ b/arch/arm/mach-at91/at91sam926x_time.c
@@ -1,5 +1,5 @@
 /*
- * linux/arch/arm/mach-at91rm9200/at91sam926x_time.c
+ * linux/arch/arm/mach-at91/at91sam926x_time.c
  *
  * Copyright (C) 2005-2006 M. Amine SAYA, ATMEL Rousset, France
  * Revision	 2005 M. Nicolas Diremdjian, ATMEL Rousset, France
@@ -30,7 +30,6 @@
  * Returns number of microseconds since last timer interrupt.  Note that interrupts
  * will have been disabled by do_gettimeofday()
  *  'LATCH' is hwclock ticks (see CLOCK_TICK_RATE in timex.h) per jiffy.
- *  'tick' is usecs per jiffy (linux/timex.h).
  */
 static unsigned long at91sam926x_gettimeoffset(void)
 {
@@ -39,7 +38,7 @@ static unsigned long at91sam926x_gettimeoffset(void)
 
 	elapsed = (PIT_PICNT(t) * LATCH) + PIT_CPIV(t);		/* hardware clock cycles */
 
-	return (unsigned long)(elapsed * 1000000) / LATCH;
+	return (unsigned long)(elapsed * jiffies_to_usecs(1)) / LATCH;
 }
 
 /*
diff --git a/arch/arm/mach-at91rm9200/board-1arm.c b/arch/arm/mach-at91/board-1arm.c
index 971c3e2d8e3..2d3d4b6f7b0 100644
--- a/arch/arm/mach-at91rm9200/board-1arm.c
+++ b/arch/arm/mach-at91/board-1arm.c
@@ -1,5 +1,5 @@
 /*
- * linux/arch/arm/mach-at91rm9200/board-1arm.c
+ * linux/arch/arm/mach-at91/board-1arm.c
  *
  *  Copyright (C) 2005 SAN People
  *
diff --git a/arch/arm/mach-at91rm9200/board-carmeva.c b/arch/arm/mach-at91/board-carmeva.c
index 654f0379550..b4518619063 100644
--- a/arch/arm/mach-at91rm9200/board-carmeva.c
+++ b/arch/arm/mach-at91/board-carmeva.c
@@ -1,5 +1,5 @@
 /*
- * linux/arch/arm/mach-at91rm9200/board-carmeva.c
+ * linux/arch/arm/mach-at91/board-carmeva.c
  *
  *  Copyright (c) 2005 Peer Georgi
  *  		       Conitec Datasystems
@@ -134,7 +134,7 @@ static void __init carmeva_board_init(void)
 	/* Compact Flash */
 //	at91_add_device_cf(&carmeva_cf_data);
 	/* MMC */
-	at91_add_device_mmc(&carmeva_mmc_data);
+	at91_add_device_mmc(0, &carmeva_mmc_data);
 }
 
 MACHINE_START(CARMEVA, "Carmeva")
diff --git a/arch/arm/mach-at91rm9200/board-csb337.c b/arch/arm/mach-at91/board-csb337.c
index b8bb8052607..e18a41e61f0 100644
--- a/arch/arm/mach-at91rm9200/board-csb337.c
+++ b/arch/arm/mach-at91/board-csb337.c
@@ -1,5 +1,5 @@
 /*
- * linux/arch/arm/mach-at91rm9200/board-csb337.c
+ * linux/arch/arm/mach-at91/board-csb337.c
  *
  *  Copyright (C) 2005 SAN People
  *
@@ -24,6 +24,7 @@
 #include <linux/module.h>
 #include <linux/platform_device.h>
 #include <linux/spi/spi.h>
+#include <linux/mtd/physmap.h>
 
 #include <asm/hardware.h>
 #include <asm/setup.h>
@@ -112,6 +113,42 @@ static struct spi_board_info csb337_spi_devices[] = {
 	},
 };
 
+#define CSB_FLASH_BASE	AT91_CHIPSELECT_0
+#define CSB_FLASH_SIZE	0x800000
+
+static struct mtd_partition csb_flash_partitions[] = {
+	{
+		.name		= "uMON flash",
+		.offset		= 0,
+		.size		= MTDPART_SIZ_FULL,
+		.mask_flags	= MTD_WRITEABLE,	/* read only */
+	}
+};
+
+static struct physmap_flash_data csb_flash_data = {
+	.width		= 2,
+	.parts		= csb_flash_partitions,
+	.nr_parts	= ARRAY_SIZE(csb_flash_partitions),
+};
+
+static struct resource csb_flash_resources[] = {
+	{
+		.start	= CSB_FLASH_BASE,
+		.end	= CSB_FLASH_BASE + CSB_FLASH_SIZE - 1,
+		.flags	= IORESOURCE_MEM,
+	}
+};
+
+static struct platform_device csb_flash = {
+	.name		= "physmap-flash",
+	.id		= 0,
+	.dev		= {
+				.platform_data = &csb_flash_data,
+			},
+	.resource	= csb_flash_resources,
+	.num_resources	= ARRAY_SIZE(csb_flash_resources),
+};
+
 static void __init csb337_board_init(void)
 {
 	/* Serial */
@@ -130,7 +167,9 @@ static void __init csb337_board_init(void)
 	/* SPI */
 	at91_add_device_spi(csb337_spi_devices, ARRAY_SIZE(csb337_spi_devices));
 	/* MMC */
-	at91_add_device_mmc(&csb337_mmc_data);
+	at91_add_device_mmc(0, &csb337_mmc_data);
+	/* NOR flash */
+	platform_device_register(&csb_flash);
 }
 
 MACHINE_START(CSB337, "Cogent CSB337")
diff --git a/arch/arm/mach-at91rm9200/board-csb637.c b/arch/arm/mach-at91/board-csb637.c
index a29fa0e822c..77f04b935b3 100644
--- a/arch/arm/mach-at91rm9200/board-csb637.c
+++ b/arch/arm/mach-at91/board-csb637.c
@@ -1,5 +1,5 @@
 /*
- * linux/arch/arm/mach-at91rm9200/board-csb637.c
+ * linux/arch/arm/mach-at91/board-csb637.c
  *
  *  Copyright (C) 2005 SAN People
  *
@@ -23,6 +23,7 @@
 #include <linux/mm.h>
 #include <linux/module.h>
 #include <linux/platform_device.h>
+#include <linux/mtd/physmap.h>
 
 #include <asm/hardware.h>
 #include <asm/setup.h>
@@ -81,6 +82,42 @@ static struct at91_udc_data __initdata csb637_udc_data = {
 	.pullup_pin   = AT91_PIN_PB1,
 };
 
+#define CSB_FLASH_BASE	AT91_CHIPSELECT_0
+#define CSB_FLASH_SIZE	0x1000000
+
+static struct mtd_partition csb_flash_partitions[] = {
+	{
+		.name		= "uMON flash",
+		.offset		= 0,
+		.size		= MTDPART_SIZ_FULL,
+		.mask_flags	= MTD_WRITEABLE,	/* read only */
+	}
+};
+
+static struct physmap_flash_data csb_flash_data = {
+	.width		= 2,
+	.parts		= csb_flash_partitions,
+	.nr_parts	= ARRAY_SIZE(csb_flash_partitions),
+};
+
+static struct resource csb_flash_resources[] = {
+	{
+		.start	= CSB_FLASH_BASE,
+		.end	= CSB_FLASH_BASE + CSB_FLASH_SIZE - 1,
+		.flags	= IORESOURCE_MEM,
+	}
+};
+
+static struct platform_device csb_flash = {
+	.name		= "physmap-flash",
+	.id		= 0,
+	.dev		= {
+				.platform_data = &csb_flash_data,
+			},
+	.resource	= csb_flash_resources,
+	.num_resources	= ARRAY_SIZE(csb_flash_resources),
+};
+
 static void __init csb637_board_init(void)
 {
 	/* Serial */
@@ -95,6 +132,8 @@ static void __init csb637_board_init(void)
 	at91_add_device_i2c();
 	/* SPI */
 	at91_add_device_spi(NULL, 0);
+	/* NOR flash */
+	platform_device_register(&csb_flash);
 }
 
 MACHINE_START(CSB637, "Cogent CSB637")
diff --git a/arch/arm/mach-at91rm9200/board-dk.c b/arch/arm/mach-at91/board-dk.c
index 7522bf91bce..6043c38c0a9 100644
--- a/arch/arm/mach-at91rm9200/board-dk.c
+++ b/arch/arm/mach-at91/board-dk.c
@@ -1,5 +1,5 @@
 /*
- * linux/arch/arm/mach-at91rm9200/board-dk.c
+ * linux/arch/arm/mach-at91/board-dk.c
  *
  *  Copyright (C) 2005 SAN People
  *
@@ -194,7 +194,7 @@ static void __init dk_board_init(void)
 #else
 	/* MMC */
 	at91_set_gpio_output(AT91_PIN_PB7, 1);	/* this MMC card slot can optionally use SPI signaling (CS3). */
-	at91_add_device_mmc(&dk_mmc_data);
+	at91_add_device_mmc(0, &dk_mmc_data);
 #endif
 	/* NAND */
 	at91_add_device_nand(&dk_nand_data);
diff --git a/arch/arm/mach-at91rm9200/board-eb9200.c b/arch/arm/mach-at91/board-eb9200.c
index 80b72cf7264..20458b5548f 100644
--- a/arch/arm/mach-at91rm9200/board-eb9200.c
+++ b/arch/arm/mach-at91/board-eb9200.c
@@ -1,5 +1,5 @@
 /*
- * linux/arch/arm/mach-at91rm9200/board-eb9200.c
+ * linux/arch/arm/mach-at91/board-eb9200.c
  *
  *  Copyright (C) 2005 SAN People, adapted for ATEB9200 from Embest
  *  by Andrew Patrikalakis
@@ -109,7 +109,7 @@ static void __init eb9200_board_init(void)
 	at91_add_device_spi(NULL, 0);
 	/* MMC */
 	/* only supports 1 or 4 bit interface, not wired through to SPI */
-	at91_add_device_mmc(&eb9200_mmc_data);
+	at91_add_device_mmc(0, &eb9200_mmc_data);
 }
 
 MACHINE_START(ATEB9200, "Embest ATEB9200")
diff --git a/arch/arm/mach-at91rm9200/board-ek.c b/arch/arm/mach-at91/board-ek.c
index c4fdb415f20..322fdd75a1e 100644
--- a/arch/arm/mach-at91rm9200/board-ek.c
+++ b/arch/arm/mach-at91/board-ek.c
@@ -1,5 +1,5 @@
 /*
- * linux/arch/arm/mach-at91rm9200/board-ek.c
+ * linux/arch/arm/mach-at91/board-ek.c
  *
  *  Copyright (C) 2005 SAN People
  *
@@ -154,7 +154,7 @@ static void __init ek_board_init(void)
 #else
 	/* MMC */
 	at91_set_gpio_output(AT91_PIN_PB22, 1);	/* this MMC card slot can optionally use SPI signaling (CS3). */
-	at91_add_device_mmc(&ek_mmc_data);
+	at91_add_device_mmc(0, &ek_mmc_data);
 #endif
 	/* NOR Flash */
 	platform_device_register(&ek_flash);
diff --git a/arch/arm/mach-at91rm9200/board-kafa.c b/arch/arm/mach-at91/board-kafa.c
index 6ef3c487982..c77d84ce9ca 100644
--- a/arch/arm/mach-at91rm9200/board-kafa.c
+++ b/arch/arm/mach-at91/board-kafa.c
@@ -1,5 +1,5 @@
 /*
- * linux/arch/arm/mach-at91rm9200/board-kafa.c
+ * linux/arch/arm/mach-at91/board-kafa.c
  *
  *  Copyright (C) 2006 Sperry-Sun
  *
diff --git a/arch/arm/mach-at91rm9200/board-kb9202.c b/arch/arm/mach-at91/board-kb9202.c
index 759d8191854..76f6e1e553e 100644
--- a/arch/arm/mach-at91rm9200/board-kb9202.c
+++ b/arch/arm/mach-at91/board-kb9202.c
@@ -1,5 +1,5 @@
 /*
- * linux/arch/arm/mach-at91rm9200/board-kb9202.c
+ * linux/arch/arm/mach-at91/board-kb9202.c
  *
  *  Copyright (c) 2005 kb_admin
  *  		       KwikByte, Inc.
@@ -122,7 +122,7 @@ static void __init kb9202_board_init(void)
 	/* USB Device */
 	at91_add_device_udc(&kb9202_udc_data);
 	/* MMC */
-	at91_add_device_mmc(&kb9202_mmc_data);
+	at91_add_device_mmc(0, &kb9202_mmc_data);
 	/* I2C */
 	at91_add_device_i2c();
 	/* SPI */
diff --git a/arch/arm/mach-at91rm9200/board-sam9260ek.c b/arch/arm/mach-at91/board-sam9260ek.c
index da5d58ac870..57fb4499d96 100644
--- a/arch/arm/mach-at91rm9200/board-sam9260ek.c
+++ b/arch/arm/mach-at91/board-sam9260ek.c
@@ -1,5 +1,5 @@
 /*
- * linux/arch/arm/mach-at91rm9200/board-ek.c
+ * linux/arch/arm/mach-at91/board-sam9260ek.c
  *
  *  Copyright (C) 2005 SAN People
  *  Copyright (C) 2006 Atmel
@@ -118,7 +118,7 @@ static struct spi_board_info ek_spi_devices[] = {
 /*
  * MACB Ethernet device
  */
-static struct __initdata eth_platform_data ek_macb_data = {
+static struct __initdata at91_eth_data ek_macb_data = {
 	.phy_irq_pin	= AT91_PIN_PA7,
 	.is_rmii	= 1,
 };
@@ -187,7 +187,7 @@ static void __init ek_board_init(void)
 	/* Ethernet */
 	at91_add_device_eth(&ek_macb_data);
 	/* MMC */
-	at91_add_device_mmc(&ek_mmc_data);
+	at91_add_device_mmc(0, &ek_mmc_data);
 }
 
 MACHINE_START(AT91SAM9260EK, "Atmel AT91SAM9260-EK")
diff --git a/arch/arm/mach-at91rm9200/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c
index 30b490d8886..b7e772467cf 100644
--- a/arch/arm/mach-at91rm9200/board-sam9261ek.c
+++ b/arch/arm/mach-at91/board-sam9261ek.c
@@ -1,5 +1,5 @@
 /*
- * linux/arch/arm/mach-at91rm9200/board-ek.c
+ * linux/arch/arm/mach-at91/board-sam9261ek.c
  *
  *  Copyright (C) 2005 SAN People
  *  Copyright (C) 2006 Atmel
@@ -243,7 +243,7 @@ static void __init ek_board_init(void)
 	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
 #else
 	/* MMC */
-	at91_add_device_mmc(&ek_mmc_data);
+	at91_add_device_mmc(0, &ek_mmc_data);
 #endif
 }
 
diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c
new file mode 100644
index 00000000000..8fdce11a880
--- /dev/null
+++ b/arch/arm/mach-at91/board-sam9263ek.c
@@ -0,0 +1,176 @@
+/*
+ * linux/arch/arm/mach-at91/board-sam9263ek.c
+ *
+ *  Copyright (C) 2005 SAN People
+ *  Copyright (C) 2007 Atmel Corporation.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+
+#include <asm/hardware.h>
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <asm/arch/board.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/at91sam926x_mc.h>
+
+#include "generic.h"
+
+
+/*
+ * Serial port configuration.
+ *    0 .. 2 = USART0 .. USART2
+ *    3      = DBGU
+ */
+static struct at91_uart_config __initdata ek_uart_config = {
+	.console_tty	= 0,				/* ttyS0 */
+	.nr_tty		= 2,
+	.tty_map	= { 3, 0, -1, -1, }		/* ttyS0, ..., ttyS3 */
+};
+
+static void __init ek_map_io(void)
+{
+	/* Initialize processor: 16.367 MHz crystal */
+	at91sam9263_initialize(16367660);
+
+	/* Setup the serial ports and console */
+	at91_init_serial(&ek_uart_config);
+}
+
+static void __init ek_init_irq(void)
+{
+	at91sam9263_init_interrupts(NULL);
+}
+
+
+/*
+ * USB Host port
+ */
+static struct at91_usbh_data __initdata ek_usbh_data = {
+	.ports		= 2,
+	.vbus_pin	= { AT91_PIN_PA24, AT91_PIN_PA21 },
+};
+
+/*
+ * USB Device port
+ */
+static struct at91_udc_data __initdata ek_udc_data = {
+	.vbus_pin	= AT91_PIN_PA25,
+	.pullup_pin	= 0,		/* pull-up driven by UDC */
+};
+
+
+/*
+ * SPI devices.
+ */
+static struct spi_board_info ek_spi_devices[] = {
+#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
+	{	/* DataFlash card */
+		.modalias	= "mtd_dataflash",
+		.chip_select	= 0,
+		.max_speed_hz	= 15 * 1000 * 1000,
+		.bus_num	= 0,
+	},
+#endif
+};
+
+
+/*
+ * MCI (SD/MMC)
+ */
+static struct at91_mmc_data __initdata ek_mmc_data = {
+	.wire4		= 1,
+	.det_pin	= AT91_PIN_PE18,
+	.wp_pin		= AT91_PIN_PE19,
+//	.vcc_pin	= ... not connected
+};
+
+
+/*
+ * NAND flash
+ */
+static struct mtd_partition __initdata ek_nand_partition[] = {
+	{
+		.name	= "Partition 1",
+		.offset	= 0,
+		.size	= 64 * 1024 * 1024,
+	},
+	{
+		.name	= "Partition 2",
+		.offset	= 64 * 1024 * 1024,
+		.size	= MTDPART_SIZ_FULL,
+	},
+};
+
+static struct mtd_partition *nand_partitions(int size, int *num_partitions)
+{
+	*num_partitions = ARRAY_SIZE(ek_nand_partition);
+	return ek_nand_partition;
+}
+
+static struct at91_nand_data __initdata ek_nand_data = {
+	.ale		= 21,
+	.cle		= 22,
+//	.det_pin	= ... not connected
+	.rdy_pin	= AT91_PIN_PA22,
+	.enable_pin	= AT91_PIN_PD15,
+	.partition_info	= nand_partitions,
+#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
+	.bus_width_16	= 1,
+#else
+	.bus_width_16	= 0,
+#endif
+};
+
+
+static void __init ek_board_init(void)
+{
+	/* Serial */
+	at91_add_device_serial();
+	/* USB Host */
+	at91_add_device_usbh(&ek_usbh_data);
+	/* USB Device */
+	at91_add_device_udc(&ek_udc_data);
+	/* SPI */
+	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
+	/* MMC */
+	at91_add_device_mmc(1, &ek_mmc_data);
+	/* NAND */
+	at91_add_device_nand(&ek_nand_data);
+}
+
+MACHINE_START(AT91SAM9263EK, "Atmel AT91SAM9263-EK")
+	/* Maintainer: Atmel */
+	.phys_io	= AT91_BASE_SYS,
+	.io_pg_offst	= (AT91_VA_BASE_SYS >> 18) & 0xfffc,
+	.boot_params	= AT91_SDRAM_BASE + 0x100,
+	.timer		= &at91sam926x_timer,
+	.map_io		= ek_map_io,
+	.init_irq	= ek_init_irq,
+	.init_machine	= ek_board_init,
+MACHINE_END
diff --git a/arch/arm/mach-at91rm9200/clock.c b/arch/arm/mach-at91/clock.c
index 4dee21fefe5..f6cb7480604 100644
--- a/arch/arm/mach-at91rm9200/clock.c
+++ b/arch/arm/mach-at91/clock.c
@@ -1,5 +1,5 @@
 /*
- * linux/arch/arm/mach-at91rm9200/clock.c
+ * linux/arch/arm/mach-at91/clock.c
  *
  * Copyright (C) 2005 David Brownell
  * Copyright (C) 2005 Ivan Kokshaysky
@@ -525,27 +525,6 @@ fail:
 	return 0;
 }
 
-/*
- * Several unused clocks may be active.  Turn them off.
- */
-static void __init at91_periphclk_reset(void)
-{
-	unsigned long reg;
-	struct clk *clk;
-
-	reg = at91_sys_read(AT91_PMC_PCSR);
-
-	list_for_each_entry(clk, &clocks, node) {
-		if (clk->mode != pmc_periph_mode)
-			continue;
-
-		if (clk->users > 0)
-			reg &= ~clk->pmc_mask;
-	}
-
-	at91_sys_write(AT91_PMC_PCDR, reg);
-}
-
 static struct clk *const standard_pmc_clocks[] __initdata = {
 	/* four primary clocks */
 	&clk32k,
@@ -586,7 +565,7 @@ int __init at91_clock_init(unsigned long main_clock)
 		pr_info("Clocks: PLLA overclocked, %ld MHz\n", plla.rate_hz / 1000000);
 
 	/*
-	 * USB clock init:  choose 48 MHz PLLB value, turn all clocks off,
+	 * USB clock init:  choose 48 MHz PLLB value,
 	 * disable 48MHz clock during usb peripheral suspend.
 	 *
 	 * REVISIT:  assumes MCK doesn't derive from PLLB!
@@ -596,16 +575,10 @@ int __init at91_clock_init(unsigned long main_clock)
 	if (cpu_is_at91rm9200()) {
 		uhpck.pmc_mask = AT91RM9200_PMC_UHP;
 		udpck.pmc_mask = AT91RM9200_PMC_UDP;
-		at91_sys_write(AT91_PMC_SCDR, AT91RM9200_PMC_UHP | AT91RM9200_PMC_UDP);
 		at91_sys_write(AT91_PMC_SCER, AT91RM9200_PMC_MCKUDP);
-	} else if (cpu_is_at91sam9260()) {
+	} else if (cpu_is_at91sam9260() || cpu_is_at91sam9261() || cpu_is_at91sam9263()) {
 		uhpck.pmc_mask = AT91SAM926x_PMC_UHP;
 		udpck.pmc_mask = AT91SAM926x_PMC_UDP;
-		at91_sys_write(AT91_PMC_SCDR, AT91SAM926x_PMC_UHP | AT91SAM926x_PMC_UDP);
-	} else if (cpu_is_at91sam9261()) {
-		uhpck.pmc_mask = (AT91SAM926x_PMC_UHP | AT91_PMC_HCK0);
-		udpck.pmc_mask = AT91SAM926x_PMC_UDP;
-		at91_sys_write(AT91_PMC_SCDR, AT91SAM926x_PMC_UHP | AT91_PMC_HCK0 | AT91SAM926x_PMC_UDP);
 	}
 	at91_sys_write(AT91_CKGR_PLLBR, 0);
 
@@ -634,11 +607,34 @@ int __init at91_clock_init(unsigned long main_clock)
 		(unsigned) main_clock / 1000000,
 		((unsigned) main_clock % 1000000) / 1000);
 
-	/* disable all programmable clocks */
-	at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK0 | AT91_PMC_PCK1 | AT91_PMC_PCK2 | AT91_PMC_PCK3);
+	return 0;
+}
+
+/*
+ * Several unused clocks may be active.  Turn them off.
+ */
+static int __init at91_clock_reset(void)
+{
+	unsigned long pcdr = 0;
+	unsigned long scdr = 0;
+	struct clk *clk;
+
+	list_for_each_entry(clk, &clocks, node) {
+		if (clk->users > 0)
+			continue;
+
+		if (clk->mode == pmc_periph_mode)
+			pcdr |= clk->pmc_mask;
+
+		if (clk->mode == pmc_sys_mode)
+			scdr |= clk->pmc_mask;
+
+		pr_debug("Clocks: disable unused %s\n", clk->name);
+	}
 
-	/* disable all other unused peripheral clocks */
-	at91_periphclk_reset();
+	at91_sys_write(AT91_PMC_PCDR, pcdr);
+	at91_sys_write(AT91_PMC_SCDR, scdr);
 
 	return 0;
 }
+late_initcall(at91_clock_reset);
diff --git a/arch/arm/mach-at91rm9200/clock.h b/arch/arm/mach-at91/clock.h
index b5c7a2eb2d1..1ba3b95ff35 100644
--- a/arch/arm/mach-at91rm9200/clock.h
+++ b/arch/arm/mach-at91/clock.h
@@ -1,5 +1,5 @@
 /*
- * linux/arch/arm/mach-at91rm9200/clock.h
+ * linux/arch/arm/mach-at91/clock.h
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
diff --git a/arch/arm/mach-at91rm9200/generic.h b/arch/arm/mach-at91/generic.h
index 8c4d5a77d48..bda26221c52 100644
--- a/arch/arm/mach-at91rm9200/generic.h
+++ b/arch/arm/mach-at91/generic.h
@@ -1,5 +1,5 @@
 /*
- * linux/arch/arm/mach-at91rm9200/generic.h
+ * linux/arch/arm/mach-at91/generic.h
  *
  *  Copyright (C) 2005 David Brownell
  *
@@ -12,11 +12,13 @@
 extern void __init at91rm9200_initialize(unsigned long main_clock, unsigned short banks);
 extern void __init at91sam9260_initialize(unsigned long main_clock);
 extern void __init at91sam9261_initialize(unsigned long main_clock);
+extern void __init at91sam9263_initialize(unsigned long main_clock);
 
  /* Interrupts */
 extern void __init at91rm9200_init_interrupts(unsigned int priority[]);
 extern void __init at91sam9260_init_interrupts(unsigned int priority[]);
 extern void __init at91sam9261_init_interrupts(unsigned int priority[]);
+extern void __init at91sam9263_init_interrupts(unsigned int priority[]);
 extern void __init at91_aic_init(unsigned int priority[]);
 
  /* Timer */
diff --git a/arch/arm/mach-at91rm9200/gpio.c b/arch/arm/mach-at91/gpio.c
index af22659c8a2..9b7495cd555 100644
--- a/arch/arm/mach-at91rm9200/gpio.c
+++ b/arch/arm/mach-at91/gpio.c
@@ -1,5 +1,5 @@
 /*
- * linux/arch/arm/mach-at91rm9200/gpio.c
+ * linux/arch/arm/mach-at91/gpio.c
  *
  * Copyright (C) 2005 HP Labs
  *
diff --git a/arch/arm/mach-at91rm9200/irq.c b/arch/arm/mach-at91/irq.c
index 2148daafd29..78a5cdb746d 100644
--- a/arch/arm/mach-at91rm9200/irq.c
+++ b/arch/arm/mach-at91/irq.c
@@ -1,5 +1,5 @@
 /*
- * linux/arch/arm/mach-at91rm9200/irq.c
+ * linux/arch/arm/mach-at91/irq.c
  *
  *  Copyright (C) 2004 SAN People
  *  Copyright (C) 2004 ATMEL
diff --git a/arch/arm/mach-at91rm9200/leds.c b/arch/arm/mach-at91/leds.c
index 1a333730466..0d514497398 100644
--- a/arch/arm/mach-at91rm9200/leds.c
+++ b/arch/arm/mach-at91/leds.c
@@ -86,10 +86,6 @@ static int __init leds_init(void)
 	if (!at91_leds_timer || !at91_leds_cpu)
 		return -ENODEV;
 
-	/* Enable PIO to access the LEDs */
-	at91_set_gpio_output(at91_leds_timer, 1);
-	at91_set_gpio_output(at91_leds_cpu, 1);
-
 	leds_event = at91_leds_event;
 
 	leds_event(led_start);
diff --git a/arch/arm/mach-at91rm9200/pm.c b/arch/arm/mach-at91/pm.c
index 67aa5572a3e..b49bfda53d7 100644
--- a/arch/arm/mach-at91rm9200/pm.c
+++ b/arch/arm/mach-at91/pm.c
@@ -1,5 +1,5 @@
 /*
- * arch/arm/mach-at91rm9200/pm.c
+ * arch/arm/mach-at91/pm.c
  * AT91 Power Management
  *
  * Copyright (C) 2005 David Brownell
@@ -80,6 +80,8 @@ static int at91_pm_verify_clocks(void)
 #warning "Check SAM9260 USB clocks"
 	} else if (cpu_is_at91sam9261()) {
 #warning "Check SAM9261 USB clocks"
+	} else if (cpu_is_at91sam9263()) {
+#warning "Check SAM9263 USB clocks"
 	}
 
 #ifdef CONFIG_AT91_PROGRAMMABLE_CLOCKS
diff --git a/arch/arm/mach-ep93xx/clock.c b/arch/arm/mach-ep93xx/clock.c
index 08ad782c164..f174d1a3b11 100644
--- a/arch/arm/mach-ep93xx/clock.c
+++ b/arch/arm/mach-ep93xx/clock.c
@@ -13,6 +13,7 @@
 #include <linux/kernel.h>
 #include <linux/clk.h>
 #include <linux/err.h>
+#include <linux/module.h>
 #include <linux/string.h>
 #include <asm/div64.h>
 #include <asm/hardware.h>
@@ -124,7 +125,7 @@ static unsigned long calc_pll_rate(u32 config_word)
 	return (unsigned long)rate;
 }
 
-void ep93xx_clock_init(void)
+static int __init ep93xx_clock_init(void)
 {
 	u32 value;
 
@@ -153,4 +154,7 @@ void ep93xx_clock_init(void)
 	printk(KERN_INFO "ep93xx: FCLK %ld MHz, HCLK %ld MHz, PCLK %ld MHz\n",
 		clk_f.rate / 1000000, clk_h.rate / 1000000,
 		clk_p.rate / 1000000);
+
+	return 0;
 }
+arch_initcall(ep93xx_clock_init);
diff --git a/arch/arm/mach-ep93xx/core.c b/arch/arm/mach-ep93xx/core.c
index 6b26346191c..829aed696d9 100644
--- a/arch/arm/mach-ep93xx/core.c
+++ b/arch/arm/mach-ep93xx/core.c
@@ -152,22 +152,30 @@ struct sys_timer ep93xx_timer = {
 /*************************************************************************
  * GPIO handling for EP93xx
  *************************************************************************/
-static unsigned char gpio_int_enable[2];
-static unsigned char gpio_int_type1[2];
-static unsigned char gpio_int_type2[2];
+static unsigned char gpio_int_unmasked[3];
+static unsigned char gpio_int_enabled[3];
+static unsigned char gpio_int_type1[3];
+static unsigned char gpio_int_type2[3];
 
-static void update_gpio_ab_int_params(int port)
+static void update_gpio_int_params(int abf)
 {
-	if (port == 0) {
+	if (abf == 0) {
 		__raw_writeb(0, EP93XX_GPIO_A_INT_ENABLE);
 		__raw_writeb(gpio_int_type2[0], EP93XX_GPIO_A_INT_TYPE2);
 		__raw_writeb(gpio_int_type1[0], EP93XX_GPIO_A_INT_TYPE1);
-		__raw_writeb(gpio_int_enable[0], EP93XX_GPIO_A_INT_ENABLE);
-	} else if (port == 1) {
+		__raw_writeb(gpio_int_unmasked[0] & gpio_int_enabled[0], EP93XX_GPIO_A_INT_ENABLE);
+	} else if (abf == 1) {
 		__raw_writeb(0, EP93XX_GPIO_B_INT_ENABLE);
 		__raw_writeb(gpio_int_type2[1], EP93XX_GPIO_B_INT_TYPE2);
 		__raw_writeb(gpio_int_type1[1], EP93XX_GPIO_B_INT_TYPE1);
-		__raw_writeb(gpio_int_enable[1], EP93XX_GPIO_B_INT_ENABLE);
+		__raw_writeb(gpio_int_unmasked[1] & gpio_int_enabled[1], EP93XX_GPIO_B_INT_ENABLE);
+	} else if (abf == 2) {
+		__raw_writeb(0, EP93XX_GPIO_F_INT_ENABLE);
+		__raw_writeb(gpio_int_type2[2], EP93XX_GPIO_F_INT_TYPE2);
+		__raw_writeb(gpio_int_type1[2], EP93XX_GPIO_F_INT_TYPE1);
+		__raw_writeb(gpio_int_unmasked[2] & gpio_int_enabled[2], EP93XX_GPIO_F_INT_ENABLE);
+	} else {
+		BUG();
 	}
 }
 
@@ -192,8 +200,13 @@ void gpio_line_config(int line, int direction)
 	local_irq_save(flags);
 	if (direction == GPIO_OUT) {
 		if (line >= 0 && line < 16) {
-			gpio_int_enable[line >> 3] &= ~(1 << (line & 7));
-			update_gpio_ab_int_params(line >> 3);
+			/* Port A/B.  */
+			gpio_int_unmasked[line >> 3] &= ~(1 << (line & 7));
+			update_gpio_int_params(line >> 3);
+		} else if (line >= 40 && line < 48) {
+			/* Port F.  */
+			gpio_int_unmasked[2] &= ~(1 << (line & 7));
+			update_gpio_int_params(2);
 		}
 
 		v = __raw_readb(data_direction_register);
@@ -244,8 +257,7 @@ EXPORT_SYMBOL(gpio_line_set);
 /*************************************************************************
  * EP93xx IRQ handling
  *************************************************************************/
-static void ep93xx_gpio_ab_irq_handler(unsigned int irq,
-		struct irq_desc *desc)
+static void ep93xx_gpio_ab_irq_handler(unsigned int irq, struct irq_desc *desc)
 {
 	unsigned char status;
 	int i;
@@ -267,37 +279,46 @@ static void ep93xx_gpio_ab_irq_handler(unsigned int irq,
 	}
 }
 
-static void ep93xx_gpio_ab_irq_mask_ack(unsigned int irq)
+static void ep93xx_gpio_f_irq_handler(unsigned int irq, struct irq_desc *desc)
+{
+	int gpio_irq = IRQ_EP93XX_GPIO(16) + (((irq + 1) & 7) ^ 4);
+
+	desc_handle_irq(gpio_irq, irq_desc + gpio_irq);
+}
+
+static void ep93xx_gpio_irq_mask_ack(unsigned int irq)
 {
 	int line = irq - IRQ_EP93XX_GPIO(0);
 	int port = line >> 3;
 
-	gpio_int_enable[port] &= ~(1 << (line & 7));
-	update_gpio_ab_int_params(port);
+	gpio_int_unmasked[port] &= ~(1 << (line & 7));
+	update_gpio_int_params(port);
 
-	if (line >> 3) {
-		__raw_writel(1 << (line & 7), EP93XX_GPIO_B_INT_ACK);
-	} else {
+	if (port == 0) {
 		__raw_writel(1 << (line & 7), EP93XX_GPIO_A_INT_ACK);
+	} else if (port == 1) {
+		__raw_writel(1 << (line & 7), EP93XX_GPIO_B_INT_ACK);
+	} else if (port == 2) {
+		__raw_writel(1 << (line & 7), EP93XX_GPIO_F_INT_ACK);
 	}
 }
 
-static void ep93xx_gpio_ab_irq_mask(unsigned int irq)
+static void ep93xx_gpio_irq_mask(unsigned int irq)
 {
 	int line = irq - IRQ_EP93XX_GPIO(0);
 	int port = line >> 3;
 
-	gpio_int_enable[port] &= ~(1 << (line & 7));
-	update_gpio_ab_int_params(port);
+	gpio_int_unmasked[port] &= ~(1 << (line & 7));
+	update_gpio_int_params(port);
 }
 
-static void ep93xx_gpio_ab_irq_unmask(unsigned int irq)
+static void ep93xx_gpio_irq_unmask(unsigned int irq)
 {
 	int line = irq - IRQ_EP93XX_GPIO(0);
 	int port = line >> 3;
 
-	gpio_int_enable[port] |= 1 << (line & 7);
-	update_gpio_ab_int_params(port);
+	gpio_int_unmasked[port] |= 1 << (line & 7);
+	update_gpio_int_params(port);
 }
 
 
@@ -306,40 +327,51 @@ static void ep93xx_gpio_ab_irq_unmask(unsigned int irq)
  * edge (1) triggered, while gpio_int_type2 controls whether it
  * triggers on low/falling (0) or high/rising (1).
  */
-static int ep93xx_gpio_ab_irq_type(unsigned int irq, unsigned int type)
+static int ep93xx_gpio_irq_type(unsigned int irq, unsigned int type)
 {
 	int port;
 	int line;
 
 	line = irq - IRQ_EP93XX_GPIO(0);
-	gpio_line_config(line, GPIO_IN);
+	if (line >= 0 && line < 16) {
+		gpio_line_config(line, GPIO_IN);
+	} else {
+		gpio_line_config(EP93XX_GPIO_LINE_F(line), GPIO_IN);
+	}
 
 	port = line >> 3;
 	line &= 7;
 
 	if (type & IRQT_RISING) {
+		gpio_int_enabled[port] |= 1 << line;
 		gpio_int_type1[port] |= 1 << line;
 		gpio_int_type2[port] |= 1 << line;
 	} else if (type & IRQT_FALLING) {
+		gpio_int_enabled[port] |= 1 << line;
 		gpio_int_type1[port] |= 1 << line;
 		gpio_int_type2[port] &= ~(1 << line);
 	} else if (type & IRQT_HIGH) {
+		gpio_int_enabled[port] |= 1 << line;
 		gpio_int_type1[port] &= ~(1 << line);
 		gpio_int_type2[port] |= 1 << line;
 	} else if (type & IRQT_LOW) {
+		gpio_int_enabled[port] |= 1 << line;
 		gpio_int_type1[port] &= ~(1 << line);
 		gpio_int_type2[port] &= ~(1 << line);
+	} else {
+		gpio_int_enabled[port] &= ~(1 << line);
 	}
-	update_gpio_ab_int_params(port);
+	update_gpio_int_params(port);
 
 	return 0;
 }
 
-static struct irq_chip ep93xx_gpio_ab_irq_chip = {
-	.ack		= ep93xx_gpio_ab_irq_mask_ack,
-	.mask		= ep93xx_gpio_ab_irq_mask,
-	.unmask		= ep93xx_gpio_ab_irq_unmask,
-	.set_type	= ep93xx_gpio_ab_irq_type,
+static struct irq_chip ep93xx_gpio_irq_chip = {
+	.name		= "GPIO",
+	.ack		= ep93xx_gpio_irq_mask_ack,
+	.mask		= ep93xx_gpio_irq_mask,
+	.unmask		= ep93xx_gpio_irq_unmask,
+	.set_type	= ep93xx_gpio_irq_type,
 };
 
 
@@ -350,12 +382,21 @@ void __init ep93xx_init_irq(void)
 	vic_init((void *)EP93XX_VIC1_BASE, 0, EP93XX_VIC1_VALID_IRQ_MASK);
 	vic_init((void *)EP93XX_VIC2_BASE, 32, EP93XX_VIC2_VALID_IRQ_MASK);
 
-	for (irq = IRQ_EP93XX_GPIO(0) ; irq <= IRQ_EP93XX_GPIO(15); irq++) {
-		set_irq_chip(irq, &ep93xx_gpio_ab_irq_chip);
+	for (irq = IRQ_EP93XX_GPIO(0); irq <= IRQ_EP93XX_GPIO(23); irq++) {
+		set_irq_chip(irq, &ep93xx_gpio_irq_chip);
 		set_irq_handler(irq, handle_level_irq);
 		set_irq_flags(irq, IRQF_VALID);
 	}
+
 	set_irq_chained_handler(IRQ_EP93XX_GPIO_AB, ep93xx_gpio_ab_irq_handler);
+	set_irq_chained_handler(IRQ_EP93XX_GPIO0MUX, ep93xx_gpio_f_irq_handler);
+	set_irq_chained_handler(IRQ_EP93XX_GPIO1MUX, ep93xx_gpio_f_irq_handler);
+	set_irq_chained_handler(IRQ_EP93XX_GPIO2MUX, ep93xx_gpio_f_irq_handler);
+	set_irq_chained_handler(IRQ_EP93XX_GPIO3MUX, ep93xx_gpio_f_irq_handler);
+	set_irq_chained_handler(IRQ_EP93XX_GPIO4MUX, ep93xx_gpio_f_irq_handler);
+	set_irq_chained_handler(IRQ_EP93XX_GPIO5MUX, ep93xx_gpio_f_irq_handler);
+	set_irq_chained_handler(IRQ_EP93XX_GPIO6MUX, ep93xx_gpio_f_irq_handler);
+	set_irq_chained_handler(IRQ_EP93XX_GPIO7MUX, ep93xx_gpio_f_irq_handler);
 }
 
 
@@ -461,8 +502,6 @@ void __init ep93xx_init_devices(void)
 {
 	unsigned int v;
 
-	ep93xx_clock_init();
-
 	/*
 	 * Disallow access to MaverickCrunch initially.
 	 */
@@ -477,8 +516,4 @@ void __init ep93xx_init_devices(void)
 
 	platform_device_register(&ep93xx_rtc_device);
 	platform_device_register(&ep93xx_ohci_device);
-
-#ifdef CONFIG_CRUNCH
-	elf_hwcap |= HWCAP_CRUNCH;
-#endif
 }
diff --git a/arch/arm/mach-iop32x/n2100.c b/arch/arm/mach-iop32x/n2100.c
index 2499a7707e3..966aa51aee0 100644
--- a/arch/arm/mach-iop32x/n2100.c
+++ b/arch/arm/mach-iop32x/n2100.c
@@ -120,6 +120,20 @@ static struct hw_pci n2100_pci __initdata = {
 	.map_irq	= n2100_pci_map_irq,
 };
 
+/*
+ * Both r8169 chips on the n2100 exhibit PCI parity problems.  Set
+ * the ->broken_parity_status flag for both ports so that the r8169
+ * driver knows it should ignore error interrupts.
+ */
+static void n2100_fixup_r8169(struct pci_dev *dev)
+{
+	if (dev->bus->number == 0 &&
+	    (dev->devfn == PCI_DEVFN(1, 0) ||
+	     dev->devfn == PCI_DEVFN(2, 0)))
+		dev->broken_parity_status = 1;
+}
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_REALTEK, PCI_ANY_ID, n2100_fixup_r8169);
+
 static int __init n2100_pci_init(void)
 {
 	if (machine_is_n2100())
diff --git a/arch/arm/mach-ns9xxx/Kconfig b/arch/arm/mach-ns9xxx/Kconfig
new file mode 100644
index 00000000000..8175ba92a2f
--- /dev/null
+++ b/arch/arm/mach-ns9xxx/Kconfig
@@ -0,0 +1,21 @@
+if ARCH_NS9XXX
+
+menu "NS9xxx Implementations"
+
+config MACH_CC9P9360DEV
+	bool "Connect Core 9P 9360 on an A9M9750 Devboard"
+	select PROCESSOR_NS9360
+	select BOARD_A9M9750DEV
+	help
+	  Say Y here if you are using the Digi Connect Core 9P 9360
+	  on an A9M9750 Development Board.
+
+config PROCESSOR_NS9360
+	bool
+
+config BOARD_A9M9750DEV
+	bool
+
+endmenu
+
+endif
diff --git a/arch/arm/mach-ns9xxx/Makefile b/arch/arm/mach-ns9xxx/Makefile
new file mode 100644
index 00000000000..91e945f5e16
--- /dev/null
+++ b/arch/arm/mach-ns9xxx/Makefile
@@ -0,0 +1,5 @@
+obj-y := irq.o time.o generic.o
+
+obj-$(CONFIG_MACH_CC9P9360DEV) += mach-cc9p9360dev.o
+
+obj-$(CONFIG_BOARD_A9M9750DEV) += board-a9m9750dev.o
diff --git a/arch/arm/mach-ns9xxx/Makefile.boot b/arch/arm/mach-ns9xxx/Makefile.boot
new file mode 100644
index 00000000000..75ed64e90fa
--- /dev/null
+++ b/arch/arm/mach-ns9xxx/Makefile.boot
@@ -0,0 +1,2 @@
+zreladdr-y := 0x108000
+params_phys-y := 0x100
diff --git a/arch/arm/mach-ns9xxx/board-a9m9750dev.c b/arch/arm/mach-ns9xxx/board-a9m9750dev.c
new file mode 100644
index 00000000000..25289884a60
--- /dev/null
+++ b/arch/arm/mach-ns9xxx/board-a9m9750dev.c
@@ -0,0 +1,199 @@
+/*
+ * arch/arm/mach-ns9xxx/board-a9m9750dev.c
+ *
+ * Copyright (C) 2006,2007 by Digi International Inc.
+ * All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ */
+#include <linux/platform_device.h>
+#include <linux/serial_8250.h>
+#include <linux/irq.h>
+
+#include <asm/mach/map.h>
+
+#include <asm/arch-ns9xxx/board.h>
+#include <asm/arch-ns9xxx/regs-sys.h>
+#include <asm/arch-ns9xxx/regs-mem.h>
+#include <asm/arch-ns9xxx/regs-bbu.h>
+#include <asm/arch-ns9xxx/regs-board-a9m9750dev.h>
+
+#include "board-a9m9750dev.h"
+
+static struct map_desc board_a9m9750dev_io_desc[] __initdata = {
+	{ /* FPGA on CS0 */
+		.virtual = io_p2v(NS9XXX_CSxSTAT_PHYS(0)),
+		.pfn = __phys_to_pfn(NS9XXX_CSxSTAT_PHYS(0)),
+		.length = NS9XXX_CS0STAT_LENGTH,
+		.type = MT_DEVICE,
+	},
+};
+
+void __init board_a9m9750dev_map_io(void)
+{
+	iotable_init(board_a9m9750dev_io_desc,
+		     ARRAY_SIZE(board_a9m9750dev_io_desc));
+}
+
+static void a9m9750dev_fpga_ack_irq(unsigned int irq)
+{
+	/* nothing */
+}
+
+static void a9m9750dev_fpga_mask_irq(unsigned int irq)
+{
+	FPGA_IER &= ~(1 << (irq - FPGA_IRQ(0)));
+}
+
+static void a9m9750dev_fpga_maskack_irq(unsigned int irq)
+{
+	a9m9750dev_fpga_mask_irq(irq);
+	a9m9750dev_fpga_ack_irq(irq);
+}
+
+static void a9m9750dev_fpga_unmask_irq(unsigned int irq)
+{
+	FPGA_IER |= 1 << (irq - FPGA_IRQ(0));
+}
+
+static struct irq_chip a9m9750dev_fpga_chip = {
+	.ack		= a9m9750dev_fpga_ack_irq,
+	.mask		= a9m9750dev_fpga_mask_irq,
+	.mask_ack	= a9m9750dev_fpga_maskack_irq,
+	.unmask		= a9m9750dev_fpga_unmask_irq,
+};
+
+static void a9m9750dev_fpga_demux_handler(unsigned int irq,
+		struct irq_desc *desc)
+{
+	int stat = FPGA_ISR;
+
+	while (stat != 0) {
+		int irqno = fls(stat) - 1;
+
+		stat &= ~(1 << irqno);
+
+		desc = irq_desc + FPGA_IRQ(irqno);
+
+		desc_handle_irq(irqno, desc);
+	}
+}
+
+void __init board_a9m9750dev_init_irq(void)
+{
+	u32 reg;
+	int i;
+
+	/*
+	 * configure gpio for IRQ_EXT2
+	 * use GPIO 11, because GPIO 32 is used for the LCD
+	 */
+	/* XXX: proper GPIO handling */
+	BBU_GC(2) &= ~0x2000;
+
+	for (i = FPGA_IRQ(0); i <= FPGA_IRQ(7); ++i) {
+		set_irq_chip(i, &a9m9750dev_fpga_chip);
+		set_irq_handler(i, handle_level_irq);
+		set_irq_flags(i, IRQF_VALID);
+	}
+
+	/* IRQ_EXT2: level sensitive + active low */
+	reg = SYS_EIC(2);
+	REGSET(reg, SYS_EIC, PLTY, AL);
+	REGSET(reg, SYS_EIC, LVEDG, LEVEL);
+	SYS_EIC(2) = reg;
+
+	set_irq_chained_handler(IRQ_EXT2,
+			a9m9750dev_fpga_demux_handler);
+}
+
+static struct plat_serial8250_port board_a9m9750dev_serial8250_port[] = {
+	{
+		.iobase         = FPGA_UARTA_BASE,
+		.membase        = (unsigned char*)FPGA_UARTA_BASE,
+		.mapbase        = FPGA_UARTA_BASE,
+		.irq            = IRQ_FPGA_UARTA,
+		.iotype         = UPIO_MEM,
+		.uartclk        = 18432000,
+		.regshift       = 0,
+		.flags          = UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ,
+	}, {
+		.iobase         = FPGA_UARTB_BASE,
+		.membase        = (unsigned char*)FPGA_UARTB_BASE,
+		.mapbase        = FPGA_UARTB_BASE,
+		.irq            = IRQ_FPGA_UARTB,
+		.iotype         = UPIO_MEM,
+		.uartclk        = 18432000,
+		.regshift       = 0,
+		.flags          = UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ,
+	}, {
+		.iobase         = FPGA_UARTC_BASE,
+		.membase        = (unsigned char*)FPGA_UARTC_BASE,
+		.mapbase        = FPGA_UARTC_BASE,
+		.irq            = IRQ_FPGA_UARTC,
+		.iotype         = UPIO_MEM,
+		.uartclk        = 18432000,
+		.regshift       = 0,
+		.flags          = UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ,
+	}, {
+		.iobase         = FPGA_UARTD_BASE,
+		.membase        = (unsigned char*)FPGA_UARTD_BASE,
+		.mapbase        = FPGA_UARTD_BASE,
+		.irq            = IRQ_FPGA_UARTD,
+		.iotype         = UPIO_MEM,
+		.uartclk        = 18432000,
+		.regshift       = 0,
+		.flags          = UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ,
+	}, {
+		/* end marker */
+	},
+};
+
+static struct platform_device board_a9m9750dev_serial_device = {
+	.name = "serial8250",
+	.dev = {
+		.platform_data = board_a9m9750dev_serial8250_port,
+	},
+};
+
+static struct platform_device *board_a9m9750dev_devices[] __initdata = {
+	&board_a9m9750dev_serial_device,
+};
+
+void __init board_a9m9750dev_init_machine(void)
+{
+	u32 reg;
+
+	/* setup static CS0: memory base ... */
+	REGSETIM(SYS_SMCSSMB(0), SYS_SMCSSMB, CSxB,
+			NS9XXX_CSxSTAT_PHYS(0) >> 12);
+
+	/* ... and mask */
+	reg = SYS_SMCSSMM(0);
+	REGSETIM(reg, SYS_SMCSSMM, CSxM, 0xfffff);
+	REGSET(reg, SYS_SMCSSMM, CSEx, EN);
+	SYS_SMCSSMM(0) = reg;
+
+	/* setup static CS0: memory configuration */
+	reg = MEM_SMC(0);
+	REGSET(reg, MEM_SMC, WSMC, OFF);
+	REGSET(reg, MEM_SMC, BSMC, OFF);
+	REGSET(reg, MEM_SMC, EW, OFF);
+	REGSET(reg, MEM_SMC, PB, 1);
+	REGSET(reg, MEM_SMC, PC, AL);
+	REGSET(reg, MEM_SMC, PM, DIS);
+	REGSET(reg, MEM_SMC, MW, 8);
+	MEM_SMC(0) = reg;
+
+	/* setup static CS0: timing */
+	MEM_SMWED(0) = 0x2;
+	MEM_SMOED(0) = 0x2;
+	MEM_SMRD(0) = 0x6;
+	MEM_SMWD(0) = 0x6;
+
+	platform_add_devices(board_a9m9750dev_devices,
+			ARRAY_SIZE(board_a9m9750dev_devices));
+}
+
diff --git a/arch/arm/mach-ns9xxx/board-a9m9750dev.h b/arch/arm/mach-ns9xxx/board-a9m9750dev.h
new file mode 100644
index 00000000000..edc75abbc5d
--- /dev/null
+++ b/arch/arm/mach-ns9xxx/board-a9m9750dev.h
@@ -0,0 +1,15 @@
+/*
+ * arch/arm/mach-ns9xxx/board-a9m9750dev.h
+ *
+ * Copyright (C) 2006 by Digi International Inc.
+ * All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ */
+#include <linux/init.h>
+
+void __init board_a9m9750dev_map_io(void);
+void __init board_a9m9750dev_init_machine(void);
+void __init board_a9m9750dev_init_irq(void);
diff --git a/arch/arm/mach-ns9xxx/generic.c b/arch/arm/mach-ns9xxx/generic.c
new file mode 100644
index 00000000000..83e2b6532b2
--- /dev/null
+++ b/arch/arm/mach-ns9xxx/generic.c
@@ -0,0 +1,42 @@
+/*
+ * arch/arm/mach-ns9xxx/generic.c
+ *
+ * Copyright (C) 2006 by Digi International Inc.
+ * All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <asm/memory.h>
+#include <asm/page.h>
+#include <asm/mach-types.h>
+#include <asm/mach/map.h>
+#include <asm/arch-ns9xxx/regs-sys.h>
+#include <asm/arch-ns9xxx/regs-mem.h>
+#include <asm/arch-ns9xxx/board.h>
+
+static struct map_desc standard_io_desc[] __initdata = {
+	{ /* BBus */
+		.virtual = io_p2v(0x90000000),
+		.pfn = __phys_to_pfn(0x90000000),
+		.length = 0x00700000,
+		.type = MT_DEVICE,
+	}, { /* AHB */
+		.virtual = io_p2v(0xa0100000),
+		.pfn = __phys_to_pfn(0xa0100000),
+		.length = 0x00900000,
+		.type = MT_DEVICE,
+	},
+};
+
+void __init ns9xxx_map_io(void)
+{
+	iotable_init(standard_io_desc, ARRAY_SIZE(standard_io_desc));
+}
+
+void __init ns9xxx_init_machine(void)
+{
+}
diff --git a/arch/arm/mach-ns9xxx/generic.h b/arch/arm/mach-ns9xxx/generic.h
new file mode 100644
index 00000000000..687e291773f
--- /dev/null
+++ b/arch/arm/mach-ns9xxx/generic.h
@@ -0,0 +1,19 @@
+/*
+ * arch/arm/mach-ns9xxx/generic.h
+ *
+ * Copyright (C) 2006 by Digi International Inc.
+ * All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ */
+#include <linux/time.h>
+#include <asm/mach/time.h>
+#include <linux/init.h>
+
+void __init ns9xxx_init_irq(void);
+void __init ns9xxx_map_io(void);
+void __init ns9xxx_init_machine(void);
+
+extern struct sys_timer ns9xxx_timer;
diff --git a/arch/arm/mach-ns9xxx/irq.c b/arch/arm/mach-ns9xxx/irq.c
new file mode 100644
index 00000000000..83d92724a97
--- /dev/null
+++ b/arch/arm/mach-ns9xxx/irq.c
@@ -0,0 +1,94 @@
+/*
+ * arch/arm/mach-ns9xxx/irq.c
+ *
+ * Copyright (C) 2006,2007 by Digi International Inc.
+ * All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ */
+#include <linux/interrupt.h>
+#include <asm/mach/irq.h>
+#include <asm/mach-types.h>
+#include <asm/arch-ns9xxx/regs-sys.h>
+#include <asm/arch-ns9xxx/irqs.h>
+#include <asm/arch-ns9xxx/board.h>
+
+#include "generic.h"
+
+static void ns9xxx_ack_irq_timer(unsigned int irq)
+{
+	u32 tc = SYS_TC(irq - IRQ_TIMER0);
+
+	REGSET(tc, SYS_TCx, INTC, SET);
+	SYS_TC(irq - IRQ_TIMER0) = tc;
+
+	REGSET(tc, SYS_TCx, INTC, UNSET);
+	SYS_TC(irq - IRQ_TIMER0) = tc;
+}
+
+void (*ns9xxx_ack_irq_functions[NR_IRQS])(unsigned int) = {
+	[IRQ_TIMER0] = ns9xxx_ack_irq_timer,
+	[IRQ_TIMER1] = ns9xxx_ack_irq_timer,
+	[IRQ_TIMER2] = ns9xxx_ack_irq_timer,
+	[IRQ_TIMER3] = ns9xxx_ack_irq_timer,
+};
+
+static void ns9xxx_mask_irq(unsigned int irq)
+{
+	/* XXX: better use cpp symbols */
+	SYS_IC(irq / 4) &= ~(1 << (7 + 8 * (3 - (irq & 3))));
+}
+
+static void ns9xxx_ack_irq(unsigned int irq)
+{
+	if (!ns9xxx_ack_irq_functions[irq]) {
+		printk(KERN_ERR "no ack function for irq %u\n", irq);
+		BUG();
+	}
+
+	ns9xxx_ack_irq_functions[irq](irq);
+	SYS_ISRADDR = 0;
+}
+
+static void ns9xxx_maskack_irq(unsigned int irq)
+{
+	ns9xxx_mask_irq(irq);
+	ns9xxx_ack_irq(irq);
+}
+
+static void ns9xxx_unmask_irq(unsigned int irq)
+{
+	/* XXX: better use cpp symbols */
+	SYS_IC(irq / 4) |= 1 << (7 + 8 * (3 - (irq & 3)));
+}
+
+static struct irq_chip ns9xxx_chip = {
+	.ack		= ns9xxx_ack_irq,
+	.mask		= ns9xxx_mask_irq,
+	.mask_ack	= ns9xxx_maskack_irq,
+	.unmask		= ns9xxx_unmask_irq,
+};
+
+void __init ns9xxx_init_irq(void)
+{
+	int i;
+
+	/* disable all IRQs */
+	for (i = 0; i < 8; ++i)
+		SYS_IC(i) = (4 * i) << 24 | (4 * i + 1) << 16 |
+			(4 * i + 2) << 8 | (4 * i + 3);
+
+	/* simple interrupt prio table:
+	 * prio(x) < prio(y) <=> x < y
+	 */
+	for (i = 0; i < 32; ++i)
+		SYS_IVA(i) = i;
+
+	for (i = IRQ_WATCHDOG; i <= IRQ_EXT3; ++i) {
+		set_irq_chip(i, &ns9xxx_chip);
+		set_irq_handler(i, handle_level_irq);
+		set_irq_flags(i, IRQF_VALID);
+	}
+}
diff --git a/arch/arm/mach-ns9xxx/mach-cc9p9360dev.c b/arch/arm/mach-ns9xxx/mach-cc9p9360dev.c
new file mode 100644
index 00000000000..a193dd93151
--- /dev/null
+++ b/arch/arm/mach-ns9xxx/mach-cc9p9360dev.c
@@ -0,0 +1,41 @@
+/*
+ * arch/arm/mach-ns9xxx/mach-cc9p9360dev.c
+ *
+ * Copyright (C) 2006 by Digi International Inc.
+ * All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ */
+#include <asm/mach/arch.h>
+#include <asm/mach-types.h>
+
+#include "board-a9m9750dev.h"
+#include "generic.h"
+
+static void __init mach_cc9p9360dev_map_io(void)
+{
+	ns9xxx_map_io();
+	board_a9m9750dev_map_io();
+}
+
+static void __init mach_cc9p9360dev_init_irq(void)
+{
+	ns9xxx_init_irq();
+	board_a9m9750dev_init_irq();
+}
+
+static void __init mach_cc9p9360dev_init_machine(void)
+{
+	ns9xxx_init_machine();
+	board_a9m9750dev_init_machine();
+}
+
+MACHINE_START(CC9P9360DEV, "Connect Core 9P 9360 on an A9M9750 Devboard")
+	.map_io = mach_cc9p9360dev_map_io,
+	.init_irq = mach_cc9p9360dev_init_irq,
+	.init_machine = mach_cc9p9360dev_init_machine,
+	.timer = &ns9xxx_timer,
+	.boot_params = 0x100,
+MACHINE_END
diff --git a/arch/arm/mach-ns9xxx/time.c b/arch/arm/mach-ns9xxx/time.c
new file mode 100644
index 00000000000..eec05f18714
--- /dev/null
+++ b/arch/arm/mach-ns9xxx/time.c
@@ -0,0 +1,88 @@
+/*
+ * arch/arm/mach-ns9xxx/time.c
+ *
+ * Copyright (C) 2006 by Digi International Inc.
+ * All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ */
+#include <linux/jiffies.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <asm/arch-ns9xxx/regs-sys.h>
+#include <asm/arch-ns9xxx/clock.h>
+#include <asm/arch-ns9xxx/irqs.h>
+#include <asm/arch/system.h>
+#include "generic.h"
+
+#define TIMERCLOCKSELECT 64
+
+static u32 usecs_per_tick;
+
+static irqreturn_t
+ns9xxx_timer_interrupt(int irq, void *dev_id)
+{
+	write_seqlock(&xtime_lock);
+	timer_tick();
+	write_sequnlock(&xtime_lock);
+
+	return IRQ_HANDLED;
+}
+
+static unsigned long ns9xxx_timer_gettimeoffset(void)
+{
+	/* return the microseconds which have passed since the last interrupt
+	 * was _serviced_.  That is, if an interrupt is pending or the counter
+	 * reloads, return one periode more. */
+
+	u32 counter1 = SYS_TR(0);
+	int pending = SYS_ISR & (1 << IRQ_TIMER0);
+	u32 counter2 = SYS_TR(0);
+	u32 elapsed;
+
+	if (pending || counter2 > counter1)
+		elapsed = 2 * SYS_TRC(0) - counter2;
+	else
+		elapsed = SYS_TRC(0) - counter1;
+
+	return (elapsed * usecs_per_tick) >> 16;
+
+}
+
+static struct irqaction ns9xxx_timer_irq = {
+	.name = "NS9xxx Timer Tick",
+	.flags = IRQF_DISABLED | IRQF_TIMER,
+	.handler = ns9xxx_timer_interrupt,
+};
+
+static void __init ns9xxx_timer_init(void)
+{
+	int tc;
+
+	usecs_per_tick =
+		SH_DIV(1000000 * TIMERCLOCKSELECT, ns9xxx_cpuclock(), 16);
+
+	/* disable timer */
+	if ((tc = SYS_TC(0)) & SYS_TCx_TEN)
+		SYS_TC(0) = tc & ~SYS_TCx_TEN;
+
+	SYS_TRC(0) = SH_DIV(ns9xxx_cpuclock(), (TIMERCLOCKSELECT * HZ), 0);
+
+	REGSET(tc, SYS_TCx, TEN, EN);
+	REGSET(tc, SYS_TCx, TLCS, DIV64); /* This must match TIMERCLOCKSELECT */
+	REGSET(tc, SYS_TCx, INTS, EN);
+	REGSET(tc, SYS_TCx, UDS, DOWN);
+	REGSET(tc, SYS_TCx, TDBG, STOP);
+	REGSET(tc, SYS_TCx, TSZ, 32);
+	REGSET(tc, SYS_TCx, REN, EN);
+	SYS_TC(0) = tc;
+
+	setup_irq(IRQ_TIMER0, &ns9xxx_timer_irq);
+}
+
+struct sys_timer ns9xxx_timer = {
+	.init = ns9xxx_timer_init,
+	.offset = ns9xxx_timer_gettimeoffset,
+};
diff --git a/arch/arm/mach-pxa/generic.c b/arch/arm/mach-pxa/generic.c
index 9de1278d234..390524c4710 100644
--- a/arch/arm/mach-pxa/generic.c
+++ b/arch/arm/mach-pxa/generic.c
@@ -338,6 +338,27 @@ static struct platform_device i2c_device = {
 	.num_resources	= ARRAY_SIZE(i2c_resources),
 };
 
+#ifdef CONFIG_PXA27x
+static struct resource i2c_power_resources[] = {
+	{
+		.start	= 0x40f00180,
+		.end	= 0x40f001a3,
+		.flags	= IORESOURCE_MEM,
+	}, {
+		.start	= IRQ_PWRI2C,
+		.end	= IRQ_PWRI2C,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device i2c_power_device = {
+	.name		= "pxa2xx-i2c",
+	.id		= 1,
+	.resource	= i2c_power_resources,
+	.num_resources	= ARRAY_SIZE(i2c_resources),
+};
+#endif
+
 void __init pxa_set_i2c_info(struct i2c_pxa_platform_data *info)
 {
 	i2c_device.dev.platform_data = info;
@@ -392,6 +413,9 @@ static struct platform_device *devices[] __initdata = {
 	&stuart_device,
 	&pxaficp_device,
 	&i2c_device,
+#ifdef CONFIG_PXA27x
+	&i2c_power_device,
+#endif
 	&i2s_device,
 	&pxartc_device,
 };
diff --git a/arch/arm/mach-realview/Kconfig b/arch/arm/mach-realview/Kconfig
index 17f5f4439fe..35156ca39df 100644
--- a/arch/arm/mach-realview/Kconfig
+++ b/arch/arm/mach-realview/Kconfig
@@ -10,10 +10,21 @@ config MACH_REALVIEW_EB
 config REALVIEW_MPCORE
 	bool "Support MPcore tile"
 	depends on MACH_REALVIEW_EB
+	select CACHE_L2X0
 	help
 	  Enable support for the MPCore tile on the Realview platform.
 	  Since there are device address and interrupt differences, a
 	  kernel built with this option enabled is not compatible with
 	  other tiles.
 
+config REALVIEW_MPCORE_REVB
+	bool "Support MPcore RevB tile"
+	depends on REALVIEW_MPCORE
+	default n
+	help
+	  Enable support for the MPCore RevB tile on the Realview platform.
+	  Since there are device address differences, a
+	  kernel built with this option enabled is not compatible with
+	  other tiles.
+
 endmenu
diff --git a/arch/arm/mach-realview/platsmp.c b/arch/arm/mach-realview/platsmp.c
index b8484e15dac..fce3596f995 100644
--- a/arch/arm/mach-realview/platsmp.c
+++ b/arch/arm/mach-realview/platsmp.c
@@ -52,13 +52,14 @@ void __cpuinit platform_secondary_init(unsigned int cpu)
 	 * core (e.g. timer irq), then they will not have been enabled
 	 * for us: do so
 	 */
-	gic_cpu_init(__io_address(REALVIEW_GIC_CPU_BASE));
+	gic_cpu_init(0, __io_address(REALVIEW_GIC_CPU_BASE));
 
 	/*
 	 * let the primary processor know we're out of the
 	 * pen, then head off into the C entry point
 	 */
 	pen_release = -1;
+	smp_wmb();
 
 	/*
 	 * Synchronise with the boot thread.
@@ -102,6 +103,7 @@ int __cpuinit boot_secondary(unsigned int cpu, struct task_struct *idle)
 
 	timeout = jiffies + (1 * HZ);
 	while (time_before(jiffies, timeout)) {
+		smp_rmb();
 		if (pen_release == -1)
 			break;
 
diff --git a/arch/arm/mach-realview/realview_eb.c b/arch/arm/mach-realview/realview_eb.c
index 9741b4d3c9c..3dba666151d 100644
--- a/arch/arm/mach-realview/realview_eb.c
+++ b/arch/arm/mach-realview/realview_eb.c
@@ -31,6 +31,7 @@
 #include <asm/mach-types.h>
 #include <asm/hardware/gic.h>
 #include <asm/hardware/icst307.h>
+#include <asm/hardware/cache-l2x0.h>
 
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
@@ -57,7 +58,26 @@ static struct map_desc realview_eb_io_desc[] __initdata = {
 		.pfn		= __phys_to_pfn(REALVIEW_GIC_DIST_BASE),
 		.length		= SZ_4K,
 		.type		= MT_DEVICE,
+	},
+#ifdef CONFIG_REALVIEW_MPCORE
+	{
+		.virtual	= IO_ADDRESS(REALVIEW_GIC1_CPU_BASE),
+		.pfn		= __phys_to_pfn(REALVIEW_GIC1_CPU_BASE),
+		.length		= SZ_4K,
+		.type		= MT_DEVICE,
+	}, {
+		.virtual	= IO_ADDRESS(REALVIEW_GIC1_DIST_BASE),
+		.pfn		= __phys_to_pfn(REALVIEW_GIC1_DIST_BASE),
+		.length		= SZ_4K,
+		.type		= MT_DEVICE,
 	}, {
+		.virtual	= IO_ADDRESS(REALVIEW_MPCORE_L220_BASE),
+		.pfn		= __phys_to_pfn(REALVIEW_MPCORE_L220_BASE),
+		.length		= SZ_8K,
+		.type		= MT_DEVICE,
+	},
+#endif
+	{
 		.virtual	= IO_ADDRESS(REALVIEW_SCTL_BASE),
 		.pfn		= __phys_to_pfn(REALVIEW_SCTL_BASE),
 		.length		= SZ_4K,
@@ -138,19 +158,29 @@ static void __init gic_init_irq(void)
 #ifdef CONFIG_REALVIEW_MPCORE
 	unsigned int pldctrl;
 	writel(0x0000a05f, __io_address(REALVIEW_SYS_LOCK));
-	pldctrl = readl(__io_address(REALVIEW_SYS_BASE)	+ 0xd8);
+	pldctrl = readl(__io_address(REALVIEW_SYS_BASE)	+ REALVIEW_MPCORE_SYS_PLD_CTRL1);
 	pldctrl |= 0x00800000;	/* New irq mode */
-	writel(pldctrl, __io_address(REALVIEW_SYS_BASE) + 0xd8);
+	writel(pldctrl, __io_address(REALVIEW_SYS_BASE) + REALVIEW_MPCORE_SYS_PLD_CTRL1);
 	writel(0x00000000, __io_address(REALVIEW_SYS_LOCK));
 #endif
-	gic_dist_init(__io_address(REALVIEW_GIC_DIST_BASE));
-	gic_cpu_init(__io_address(REALVIEW_GIC_CPU_BASE));
+	gic_dist_init(0, __io_address(REALVIEW_GIC_DIST_BASE), 29);
+	gic_cpu_init(0, __io_address(REALVIEW_GIC_CPU_BASE));
+#ifdef CONFIG_REALVIEW_MPCORE
+	gic_dist_init(1, __io_address(REALVIEW_GIC1_DIST_BASE), 64);
+	gic_cpu_init(1, __io_address(REALVIEW_GIC1_CPU_BASE));
+	gic_cascade_irq(1, IRQ_EB_IRQ1);
+#endif
 }
 
 static void __init realview_eb_init(void)
 {
 	int i;
 
+#ifdef CONFIG_REALVIEW_MPCORE
+	/* 1MB (128KB/way), 8-way associativity, evmon/parity/share enabled
+	 * Bits:  .... ...0 0111 1001 0000 .... .... .... */
+	l2x0_init(__io_address(REALVIEW_MPCORE_L220_BASE), 0x00790000, 0xfe000fff);
+#endif
 	clk_register(&realview_clcd_clk);
 
 	platform_device_register(&realview_flash_device);
diff --git a/arch/arm/mach-s3c2400/Kconfig b/arch/arm/mach-s3c2400/Kconfig
new file mode 100644
index 00000000000..deab0722836
--- /dev/null
+++ b/arch/arm/mach-s3c2400/Kconfig
@@ -0,0 +1,13 @@
+# arch/arm/mach-s3c2400/Kconfig
+#
+# Copyright 2007 Simtec Electronics
+#
+# Licensed under GPLv2
+
+
+
+menu "S3C2400 Machines"
+
+
+endmenu
+
diff --git a/arch/arm/mach-s3c2400/Makefile b/arch/arm/mach-s3c2400/Makefile
new file mode 100644
index 00000000000..7e23f4e1376
--- /dev/null
+++ b/arch/arm/mach-s3c2400/Makefile
@@ -0,0 +1,15 @@
+# arch/arm/mach-s3c2400/Makefile
+#
+# Copyright 2007 Simtec Electronics
+#
+# Licensed under GPLv2
+
+obj-y				:=
+obj-m				:=
+obj-n				:=
+obj-				:=
+
+obj-$(CONFIG_CPU_S3C2400)	+= gpio.o
+
+# Machine support
+
diff --git a/arch/arm/mach-s3c2410/s3c2400-gpio.c b/arch/arm/mach-s3c2400/gpio.c
index 1576d01d5f8..758e160410e 100644
--- a/arch/arm/mach-s3c2410/s3c2400-gpio.c
+++ b/arch/arm/mach-s3c2400/gpio.c
@@ -1,4 +1,4 @@
-/* linux/arch/arm/mach-s3c2410/s3c2400-gpio.c
+/* linux/arch/arm/mach-s3c2400/gpio.c
  *
  * Copyright (c) 2006 Lucas Correia Villa Real <lucasvr@gobolinux.org>
  *
diff --git a/arch/arm/mach-s3c2410/Kconfig b/arch/arm/mach-s3c2410/Kconfig
index eb4ec411312..d4b013b283c 100644
--- a/arch/arm/mach-s3c2410/Kconfig
+++ b/arch/arm/mach-s3c2410/Kconfig
@@ -1,54 +1,51 @@
-if ARCH_S3C2410
+# arch/arm/mach-s3c2410/Kconfig
+#
+# Copyright 2007 Simtec Electronics
+#
+# Licensed under GPLv2
 
-menu "S3C24XX Implementations"
+config CPU_S3C2410
+	bool
+	depends on ARCH_S3C2410
+	select S3C2410_CLOCK
+	select S3C2410_GPIO
+	select S3C2410_PM if PM
+	help
+	  Support for S3C2410 and S3C2410A family from the S3C24XX line
+	  of Samsung Mobile CPUs.
 
-config MACH_AML_M5900
-	bool "AML M5900 Series"
-	select CPU_S3C2410
-	select PM_SIMTEC if PM
+config CPU_S3C2410_DMA
+	bool
+	depends on S3C2410_DMA && (CPU_S3C2410 || CPU_S3C2442)
+	default y if CPU_S3C2410 || CPU_S3C2442
 	help
-	   Say Y here if you are using the American Microsystems M5900 Series
-           <http://www.amltd.com>
+	  DMA device selection for S3C2410 and compatible CPUs
 
-config MACH_ANUBIS
-	bool "Simtec Electronics ANUBIS"
-	select CPU_S3C2440
-	select PM_SIMTEC if PM
+config S3C2410_PM
+	bool
 	help
-	  Say Y here if you are using the Simtec Electronics ANUBIS
-	  development system
+	  Power Management code common to S3C2410 and better
 
-config MACH_OSIRIS
-	bool "Simtec IM2440D20 (OSIRIS) module"
-	select CPU_S3C2440
-	select PM_SIMTEC if PM
+config S3C2410_GPIO
+	bool
 	help
-	  Say Y here if you are using the Simtec IM2440D20 module, also
-	  known as the Osiris.
+	  GPIO code for S3C2410 and similar processors
 
-config ARCH_BAST
-	bool "Simtec Electronics BAST (EB2410ITX)"
-	select CPU_S3C2410
-	select PM_SIMTEC if PM
-	select ISA
+config S3C2410_CLOCK
+	bool
 	help
-	  Say Y here if you are using the Simtec Electronics EB2410ITX
-	  development board (also known as BAST)
+	  Clock code for the S3C2410, and similar processors
 
-	  Product page: <http://www.simtec.co.uk/products/EB2410ITX/>.
 
-config BAST_PC104_IRQ
-	bool "BAST PC104 IRQ support"
-	depends on ARCH_BAST
-	default y
-	help
-	  Say Y	here to enable the PC104 IRQ routing on the
-	  Simtec BAST (EB2410ITX)
+menu "S3C2410 Machines"
 
-config PM_H1940
-	bool
+config ARCH_SMDK2410
+	bool "SMDK2410/A9M2410"
+	select CPU_S3C2410
+	select MACH_SMDK
 	help
-	  Internal node for H1940 and related PM
+	   Say Y here if you are using the SMDK2410 or the derived module A9M2410
+           <http://www.fsforth.de>
 
 config ARCH_H1940
 	bool "IPAQ H1940"
@@ -57,7 +54,10 @@ config ARCH_H1940
 	help
 	  Say Y here if you are using the HP IPAQ H1940
 
-	  <http://www.handhelds.org/projects/h1940.html>.
+config PM_H1940
+	bool
+	help
+	  Internal node for H1940 and related PM
 
 config MACH_N30
 	bool "Acer N30"
@@ -65,53 +65,36 @@ config MACH_N30
 	help
 	  Say Y here if you are using the Acer N30
 
-	  <http://zoo.weinigel.se/n30>.
-
-config MACH_SMDK
-	bool
-	help
-	  Common machine code for SMDK2410 and SMDK2440
-
-config ARCH_SMDK2410
-	bool "SMDK2410/A9M2410"
+config ARCH_BAST
+	bool "Simtec Electronics BAST (EB2410ITX)"
 	select CPU_S3C2410
-	select MACH_SMDK
+	select PM_SIMTEC if PM
+	select ISA
 	help
-	   Say Y here if you are using the SMDK2410 or the derived module A9M2410
-           <http://www.fsforth.de>
+	  Say Y here if you are using the Simtec Electronics EB2410ITX
+	  development board (also known as BAST)
 
-config ARCH_S3C2440
-	bool "SMDK2440"
-	select CPU_S3C2440
-	select MACH_SMDK
+config MACH_OTOM
+ 	bool "NexVision OTOM Board"
+ 	select CPU_S3C2410
 	help
-	  Say Y here if you are using the SMDK2440.
-
-config SMDK2440_CPU2440
-	bool "SMDK2440 with S3C2440 CPU module"
-	depends on ARCH_S3C2440
-	default y if ARCH_S3C2440
-	select CPU_S3C2440
-
-config SMDK2440_CPU2442
-	bool "SMDM2440 with S3C2442 CPU module"
-	depends on ARCH_S3C2440
-	select CPU_S3C2442
+ 	  Say Y here if you are using the Nex Vision OTOM board
 
-config MACH_S3C2413
-	bool
+config MACH_AML_M5900
+	bool "AML M5900 Series"
+	select CPU_S3C2410
+	select PM_SIMTEC if PM
 	help
-	  Internal node for S3C2413 version of SMDK2413, so that
-	  machine_is_s3c2413() will work when MACH_SMDK2413 is
-	  selected
+	   Say Y here if you are using the American Microsystems M5900 Series
+           <http://www.amltd.com>
 
-config MACH_SMDK2413
-	bool "SMDK2413"
-	select CPU_S3C2412
-	select MACH_S3C2413
-	select MACH_SMDK
+config BAST_PC104_IRQ
+	bool "BAST PC104 IRQ support"
+	depends on ARCH_BAST
+	default y
 	help
-	  Say Y here if you are using an SMDK2413
+	  Say Y	here to enable the PC104 IRQ routing on the
+	  Simtec BAST (EB2410ITX)
 
 config MACH_VR1000
 	bool "Thorcom VR1000"
@@ -120,202 +103,11 @@ config MACH_VR1000
 	help
 	  Say Y here if you are using the Thorcom VR1000 board.
 
-	  This linux port is currently being maintained by Simtec, on behalf
-	  of Thorcom. Any queries, please contact Thorcom first.
-
-config MACH_RX3715
-	bool "HP iPAQ rx3715"
-	select CPU_S3C2440
-	select PM_H1940 if PM
-	help
-	  Say Y here if you are using the HP iPAQ rx3715.
-
-	  See <http://www.handhelds.org/projects/rx3715.html> for more
-	  information on this project
-
-config MACH_OTOM
- 	bool "NexVision OTOM Board"
- 	select CPU_S3C2410
-	help
- 	  Say Y here if you are using the Nex Vision OTOM board
-
-config MACH_NEXCODER_2440
- 	bool "NexVision NEXCODER 2440 Light Board"
- 	select CPU_S3C2440
-	help
- 	  Say Y here if you are using the Nex Vision NEXCODER 2440 Light Board
-
-config MACH_VSTMS
-	bool "VMSTMS"
-	select CPU_S3C2412
+config MACH_QT2410
+	bool "QT2410"
+	select CPU_S3C2410
 	help
-	  Say Y here if you are using an VSTMS board
+	   Say Y here if you are using the Armzone QT2410
 
 endmenu
 
-config S3C2410_CLOCK
-	bool
-	help
-	  Clock code for the S3C2410, and similar processors
-
-config S3C2410_PM
-	bool
-	help
-	  Power Management code common to S3C2410 and better
-
-config CPU_S3C2410_DMA
-	bool
-	depends on S3C2410_DMA && (CPU_S3C2410 || CPU_S3C2442)
-	default y if CPU_S3C2410 || CPU_S3C2442
-	help
-	  DMA device selection for S3C2410 and compatible CPUs
-
-config CPU_S3C2410
-	bool
-	depends on ARCH_S3C2410
-	select S3C2410_CLOCK
-	select S3C2410_PM if PM
-	help
-	  Support for S3C2410 and S3C2410A family from the S3C24XX line
-	  of Samsung Mobile CPUs.
-
-# internal node to signify if we are only dealing with an S3C2412
-
-config CPU_S3C2412_ONLY
-	bool
-	depends on ARCH_S3C2410 && !CPU_S3C2400 && !CPU_S3C2410 && \
-		   !CPU_S3C2440 && !CPU_S3C2442 && CPU_S3C2412
-	default y if CPU_S3C2412
-
-config S3C2412_PM
-	bool
-	help
-	  Internal config node to apply S3C2412 power management
-
-config CPU_S3C2412
-	bool
-	depends on ARCH_S3C2410
-	select S3C2412_PM if PM
-	help
-	  Support for the S3C2412 and S3C2413 SoCs from the S3C24XX line
-
-config CPU_S3C244X
-	bool
-	depends on ARCH_S3C2410 && (CPU_S3C2440 || CPU_S3C2442)
-	help
-	  Support for S3C2440 and S3C2442 Samsung Mobile CPU based systems.
-
-config CPU_S3C2440
-	bool
-	depends on ARCH_S3C2410
-	select S3C2410_CLOCK
-	select S3C2410_PM if PM
-	select CPU_S3C244X
-	help
-	  Support for S3C2440 Samsung Mobile CPU based systems.
-
-config CPU_S3C2442
-	bool
-	depends on ARCH_S3C2420
-	select S3C2410_CLOCK
-	select S3C2410_PM if PM
-	select CPU_S3C244X
-	help
-	  Support for S3C2442 Samsung Mobile CPU based systems.
-
-comment "S3C2410 Boot"
-
-config S3C2410_BOOT_WATCHDOG
-	bool "S3C2410 Initialisation watchdog"
-	depends on ARCH_S3C2410 && S3C2410_WATCHDOG
-	help
-	  Say y to enable the watchdog during the kernel decompression
-	  stage. If the kernel fails to uncompress, then the watchdog
-	  will trigger a reset and the system should restart.
-
-	  Although this uses the same hardware unit as the kernel watchdog
-	  driver, it is not a replacement for it. If you use this option,
-	  you will have to use the watchdg driver to either stop the timeout
-	  or restart it. If you do not, then your kernel will reboot after
-	  startup.
-
-	  The driver uses a fixed timeout value, so the exact time till the
-	  system resets depends on the value of PCLK. The timeout on an
-	  200MHz s3c2410 should be about 30 seconds.
-
-config S3C2410_BOOT_ERROR_RESET
-	bool "S3C2410 Reboot on decompression error"
-	depends on ARCH_S3C2410
-	help
-	  Say y here to use the watchdog to reset the system if the
-	  kernel decompressor detects an error during decompression.
-
-
-comment "S3C2410 Setup"
-
-config S3C2410_DMA
-	bool "S3C2410 DMA support"
-	depends on ARCH_S3C2410
-	help
-	  S3C2410 DMA support. This is needed for drivers like sound which
-	  use the S3C2410's DMA system to move data to and from the
-	  peripheral blocks.
-
-config S3C2410_DMA_DEBUG
-	bool "S3C2410 DMA support debug"
-	depends on ARCH_S3C2410 && S3C2410_DMA
-	help
-	  Enable debugging output for the DMA code. This option sends info
-	  to the kernel log, at priority KERN_DEBUG.
-
-	  Note, it is easy to create and fill the log buffer in a small
-	  amount of time, as well as using an significant percentage of
-	  the CPU time doing so.
-
-
-config S3C2410_PM_DEBUG
-	bool "S3C2410 PM Suspend debug"
-	depends on ARCH_S3C2410 && PM
-	help
-	  Say Y here if you want verbose debugging from the PM Suspend and
-	  Resume code. See <file:Documentation/arm/Samsung-S3C24XX/Suspend.txt>
-	  for more information.
-
-config S3C2410_PM_CHECK
-	bool "S3C2410 PM Suspend Memory CRC"
-	depends on ARCH_S3C2410 && PM && CRC32
-	help
- 	  Enable the PM code's memory area checksum over sleep. This option
-	  will generate CRCs of all blocks of memory, and store them before
-	  going to sleep. The blocks are then checked on resume for any
-	  errors.
-
-config S3C2410_PM_CHECK_CHUNKSIZE
-	int "S3C2410 PM Suspend CRC Chunksize (KiB)"
-	depends on ARCH_S3C2410 && PM && S3C2410_PM_CHECK
-	default 64
-	help
-	  Set the chunksize in Kilobytes of the CRC for checking memory
-	  corruption over suspend and resume. A smaller value will mean that
-	  the CRC data block will take more memory, but wil identify any
-	  faults with better precision.
-
-config PM_SIMTEC
-	bool
-	help
-	  Common power management code for systems that are
-	  compatible with the Simtec style of power management
-
-config S3C2410_LOWLEVEL_UART_PORT
-	int "S3C2410 UART to use for low-level messages"
-	default 0
-	help
-	  Choice of which UART port to use for the low-level messages,
-	  such as the `Uncompressing...` at start time. The value of
-	  this configuration should be between zero and two. The port
-	  must have been initialised by the boot-loader before use.
-
-	  Note, this does not affect the port used by the debug messages,
-	  which is a separate configuration.
-
-endif
diff --git a/arch/arm/mach-s3c2410/Makefile b/arch/arm/mach-s3c2410/Makefile
index 27663e28cc8..9a3d3d24c08 100644
--- a/arch/arm/mach-s3c2410/Makefile
+++ b/arch/arm/mach-s3c2410/Makefile
@@ -1,92 +1,31 @@
-
+# arch/arm/mach-s3c2410/Makefile
 #
-# Makefile for the linux kernel.
+# Copyright 2007 Simtec Electronics
 #
+# Licensed under GPLv2
 
-# Object file lists.
-
-obj-y			:= cpu.o irq.o time.o gpio.o clock.o devs.o
-obj-m			:=
-obj-n			:=
-obj-			:=
-obj-dma-y		:=
-obj-dma-n		:=
-
-# DMA
-obj-$(CONFIG_S3C2410_DMA)	+= dma.o
-
-# S3C2400 support files
-obj-$(CONFIG_CPU_S3C2400)	+= s3c2400-gpio.o
-
-# S3C2410 support files
+obj-y				:=
+obj-m				:=
+obj-n				:=
+obj-				:=
 
 obj-$(CONFIG_CPU_S3C2410)	+= s3c2410.o
-obj-$(CONFIG_CPU_S3C2410)	+= s3c2410-gpio.o
-obj-$(CONFIG_CPU_S3C2410)	+= s3c2410-irq.o
-
-obj-$(CONFIG_S3C2410_PM)	+= s3c2410-pm.o s3c2410-sleep.o
-obj-$(CONFIG_CPU_S3C2410_DMA)	+= s3c2410-dma.o
-
-# Power Management support
-
-obj-$(CONFIG_PM)		+= pm.o sleep.o
-obj-$(CONFIG_PM_SIMTEC)		+= pm-simtec.o
-obj-$(CONFIG_PM_H1940)		+= pm-h1940.o
-
-# S3C2412 support
-obj-$(CONFIG_CPU_S3C2412)	+= s3c2412.o
-obj-$(CONFIG_CPU_S3C2412)	+= s3c2412-irq.o
-obj-$(CONFIG_CPU_S3C2412)	+= s3c2412-clock.o
-obj-dma-$(CONFIG_CPU_S3C2412)	+= s3c2412-dma.o
-
-obj-$(CONFIG_S3C2412_PM)	+= s3c2412-pm.o
-
-#
-# S3C244X support
-
-obj-$(CONFIG_CPU_S3C244X)	+= s3c244x.o
-obj-$(CONFIG_CPU_S3C244X)	+= s3c244x-irq.o
-
-# Clock control
-
-obj-$(CONFIG_S3C2410_CLOCK)	+= s3c2410-clock.o
-
-# S3C2440 support
-
-obj-$(CONFIG_CPU_S3C2440)	+= s3c2440.o s3c2440-dsc.o
-obj-$(CONFIG_CPU_S3C2440)	+= s3c2440-irq.o
-obj-$(CONFIG_CPU_S3C2440)	+= s3c2440-clock.o
-obj-$(CONFIG_CPU_S3C2440)	+= s3c2410-gpio.o
-obj-dma-$(CONFIG_CPU_S3C2440)	+= s3c2440-dma.o
+obj-$(CONFIG_CPU_S3C2410)	+= irq.o
+obj-$(CONFIG_CPU_S3C2410_DMA)	+= dma.o
+obj-$(CONFIG_CPU_S3C2410_DMA)	+= dma.o
+obj-$(CONFIG_S3C2410_PM)	+= pm.o sleep.o
+obj-$(CONFIG_S3C2410_GPIO)	+= gpio.o
+obj-$(CONFIG_S3C2410_CLOCK)	+= clock.o
 
-# S3C2442 support
+# Machine support
 
-obj-$(CONFIG_CPU_S3C2442)	+= s3c2442.o
-obj-$(CONFIG_CPU_S3C2442)	+= s3c2442-clock.o
-
-# bast extras
-
-obj-$(CONFIG_BAST_PC104_IRQ)	+= bast-irq.o
-
-# merge in dma objects
-
-obj-y				+= $(obj-dma-y)
-
-# machine specific support
-
-obj-$(CONFIG_MACH_AML_M5900)	+= mach-amlm5900.o
-obj-$(CONFIG_MACH_ANUBIS)	+= mach-anubis.o
-obj-$(CONFIG_MACH_OSIRIS)	+= mach-osiris.o
-obj-$(CONFIG_ARCH_BAST)		+= mach-bast.o usb-simtec.o
+obj-$(CONFIG_ARCH_SMDK2410)	+= mach-smdk2410.o
 obj-$(CONFIG_ARCH_H1940)	+= mach-h1940.o
+obj-$(CONFIG_PM_H1940)		+= pm-h1940.o
 obj-$(CONFIG_MACH_N30)		+= mach-n30.o
-obj-$(CONFIG_ARCH_SMDK2410)	+= mach-smdk2410.o
-obj-$(CONFIG_MACH_SMDK2413)	+= mach-smdk2413.o
-obj-$(CONFIG_ARCH_S3C2440)	+= mach-smdk2440.o
-obj-$(CONFIG_MACH_VR1000)	+= mach-vr1000.o usb-simtec.o
-obj-$(CONFIG_MACH_RX3715)	+= mach-rx3715.o
+obj-$(CONFIG_ARCH_BAST)		+= mach-bast.o usb-simtec.o
 obj-$(CONFIG_MACH_OTOM)		+= mach-otom.o
-obj-$(CONFIG_MACH_NEXCODER_2440) += mach-nexcoder.o
-obj-$(CONFIG_MACH_VSTMS)	+= mach-vstms.o
-
-obj-$(CONFIG_MACH_SMDK)		+= common-smdk.o
\ No newline at end of file
+obj-$(CONFIG_MACH_AML_M5900)	+= mach-amlm5900.o
+obj-$(CONFIG_BAST_PC104_IRQ)	+= bast-irq.o
+obj-$(CONFIG_MACH_VR1000)	+= mach-vr1000.o usb-simtec.o
+obj-$(CONFIG_MACH_QT2410)	+= mach-qt2410.o
diff --git a/arch/arm/mach-s3c2410/bast-irq.c b/arch/arm/mach-s3c2410/bast-irq.c
index 379efe70778..daeba427d78 100644
--- a/arch/arm/mach-s3c2410/bast-irq.c
+++ b/arch/arm/mach-s3c2410/bast-irq.c
@@ -39,7 +39,7 @@
 #include <asm/arch/bast-map.h>
 #include <asm/arch/bast-irq.h>
 
-#include "irq.h"
+#include <asm/plat-s3c24xx/irq.h>
 
 #if 0
 #include <asm/debug-ll.h>
diff --git a/arch/arm/mach-s3c2410/bast.h b/arch/arm/mach-s3c2410/bast.h
index e5d03311752..e98543742eb 100644
--- a/arch/arm/mach-s3c2410/bast.h
+++ b/arch/arm/mach-s3c2410/bast.h
@@ -1,2 +1,2 @@
-
+/* linux/arch/arm/mach-s3c2410/bast.h
 extern void bast_init_irq(void);
diff --git a/arch/arm/mach-s3c2410/clock.c b/arch/arm/mach-s3c2410/clock.c
index e13fb677889..5b4831c4c1d 100644
--- a/arch/arm/mach-s3c2410/clock.c
+++ b/arch/arm/mach-s3c2410/clock.c
@@ -1,15 +1,9 @@
 /* linux/arch/arm/mach-s3c2410/clock.c
  *
- * Copyright (c) 2004-2005 Simtec Electronics
+ * Copyright (c) 2006 Simtec Electronics
  *	Ben Dooks <ben@simtec.co.uk>
  *
- * S3C24XX Core clock control support
- *
- * Based on, and code from linux/arch/arm/mach-versatile/clock.c
- **
- **  Copyright (C) 2004 ARM Limited.
- **  Written by Deep Blue Solutions Limited.
- *
+ * S3C2410,S3C2440,S3C2442 Clock control support
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
@@ -32,418 +26,251 @@
 #include <linux/list.h>
 #include <linux/errno.h>
 #include <linux/err.h>
-#include <linux/platform_device.h>
 #include <linux/sysdev.h>
-#include <linux/interrupt.h>
-#include <linux/ioport.h>
 #include <linux/clk.h>
 #include <linux/mutex.h>
 #include <linux/delay.h>
+#include <linux/serial_core.h>
+
+#include <asm/mach/map.h>
 
 #include <asm/hardware.h>
-#include <asm/irq.h>
 #include <asm/io.h>
 
+#include <asm/arch/regs-serial.h>
 #include <asm/arch/regs-clock.h>
 #include <asm/arch/regs-gpio.h>
 
-#include "clock.h"
-#include "cpu.h"
-
-/* clock information */
+#include <asm/plat-s3c24xx/s3c2410.h>
+#include <asm/plat-s3c24xx/clock.h>
+#include <asm/plat-s3c24xx/cpu.h>
 
-static LIST_HEAD(clocks);
-
-DEFINE_MUTEX(clocks_mutex);
-
-/* enable and disable calls for use with the clk struct */
-
-static int clk_null_enable(struct clk *clk, int enable)
+int s3c2410_clkcon_enable(struct clk *clk, int enable)
 {
-	return 0;
-}
-
-/* Clock API calls */
+	unsigned int clocks = clk->ctrlbit;
+	unsigned long clkcon;
 
-struct clk *clk_get(struct device *dev, const char *id)
-{
-	struct clk *p;
-	struct clk *clk = ERR_PTR(-ENOENT);
-	int idno;
+	clkcon = __raw_readl(S3C2410_CLKCON);
 
-	if (dev == NULL || dev->bus != &platform_bus_type)
-		idno = -1;
+	if (enable)
+		clkcon |= clocks;
 	else
-		idno = to_platform_device(dev)->id;
-
-	mutex_lock(&clocks_mutex);
-
-	list_for_each_entry(p, &clocks, list) {
-		if (p->id == idno &&
-		    strcmp(id, p->name) == 0 &&
-		    try_module_get(p->owner)) {
-			clk = p;
-			break;
-		}
-	}
-
-	/* check for the case where a device was supplied, but the
-	 * clock that was being searched for is not device specific */
-
-	if (IS_ERR(clk)) {
-		list_for_each_entry(p, &clocks, list) {
-			if (p->id == -1 && strcmp(id, p->name) == 0 &&
-			    try_module_get(p->owner)) {
-				clk = p;
-				break;
-			}
-		}
-	}
+		clkcon &= ~clocks;
 
-	mutex_unlock(&clocks_mutex);
-	return clk;
-}
+	/* ensure none of the special function bits set */
+	clkcon &= ~(S3C2410_CLKCON_IDLE|S3C2410_CLKCON_POWER);
 
-void clk_put(struct clk *clk)
-{
-	module_put(clk->owner);
-}
+	__raw_writel(clkcon, S3C2410_CLKCON);
 
-int clk_enable(struct clk *clk)
-{
-	if (IS_ERR(clk) || clk == NULL)
-		return -EINVAL;
-
-	clk_enable(clk->parent);
-
-	mutex_lock(&clocks_mutex);
-
-	if ((clk->usage++) == 0)
-		(clk->enable)(clk, 1);
-
-	mutex_unlock(&clocks_mutex);
 	return 0;
 }
 
-void clk_disable(struct clk *clk)
-{
-	if (IS_ERR(clk) || clk == NULL)
-		return;
-
-	mutex_lock(&clocks_mutex);
-
-	if ((--clk->usage) == 0)
-		(clk->enable)(clk, 0);
-
-	mutex_unlock(&clocks_mutex);
-	clk_disable(clk->parent);
-}
-
-
-unsigned long clk_get_rate(struct clk *clk)
-{
-	if (IS_ERR(clk))
-		return 0;
-
-	if (clk->rate != 0)
-		return clk->rate;
-
-	if (clk->get_rate != NULL)
-		return (clk->get_rate)(clk);
-
-	if (clk->parent != NULL)
-		return clk_get_rate(clk->parent);
-
-	return clk->rate;
-}
-
-long clk_round_rate(struct clk *clk, unsigned long rate)
-{
-	if (!IS_ERR(clk) && clk->round_rate)
-		return (clk->round_rate)(clk, rate);
-
-	return rate;
-}
-
-int clk_set_rate(struct clk *clk, unsigned long rate)
-{
-	int ret;
-
-	if (IS_ERR(clk))
-		return -EINVAL;
-
-	mutex_lock(&clocks_mutex);
-	ret = (clk->set_rate)(clk, rate);
-	mutex_unlock(&clocks_mutex);
-
-	return ret;
-}
-
-struct clk *clk_get_parent(struct clk *clk)
+static int s3c2410_upll_enable(struct clk *clk, int enable)
 {
-	return clk->parent;
-}
-
-int clk_set_parent(struct clk *clk, struct clk *parent)
-{
-	int ret = 0;
-
-	if (IS_ERR(clk))
-		return -EINVAL;
-
-	mutex_lock(&clocks_mutex);
-
-	if (clk->set_parent)
-		ret = (clk->set_parent)(clk, parent);
-
-	mutex_unlock(&clocks_mutex);
-
-	return ret;
-}
-
-EXPORT_SYMBOL(clk_get);
-EXPORT_SYMBOL(clk_put);
-EXPORT_SYMBOL(clk_enable);
-EXPORT_SYMBOL(clk_disable);
-EXPORT_SYMBOL(clk_get_rate);
-EXPORT_SYMBOL(clk_round_rate);
-EXPORT_SYMBOL(clk_set_rate);
-EXPORT_SYMBOL(clk_get_parent);
-EXPORT_SYMBOL(clk_set_parent);
-
-/* base clocks */
-
-struct clk clk_xtal = {
-	.name		= "xtal",
-	.id		= -1,
-	.rate		= 0,
-	.parent		= NULL,
-	.ctrlbit	= 0,
-};
-
-struct clk clk_mpll = {
-	.name		= "mpll",
-	.id		= -1,
-};
-
-struct clk clk_upll = {
-	.name		= "upll",
-	.id		= -1,
-	.parent		= NULL,
-	.ctrlbit	= 0,
-};
-
-struct clk clk_f = {
-	.name		= "fclk",
-	.id		= -1,
-	.rate		= 0,
-	.parent		= &clk_mpll,
-	.ctrlbit	= 0,
-};
-
-struct clk clk_h = {
-	.name		= "hclk",
-	.id		= -1,
-	.rate		= 0,
-	.parent		= NULL,
-	.ctrlbit	= 0,
-};
-
-struct clk clk_p = {
-	.name		= "pclk",
-	.id		= -1,
-	.rate		= 0,
-	.parent		= NULL,
-	.ctrlbit	= 0,
-};
-
-struct clk clk_usb_bus = {
-	.name		= "usb-bus",
-	.id		= -1,
-	.rate		= 0,
-	.parent		= &clk_upll,
-};
-
-/* clocks that could be registered by external code */
-
-static int s3c24xx_dclk_enable(struct clk *clk, int enable)
-{
-	unsigned long dclkcon = __raw_readl(S3C24XX_DCLKCON);
+	unsigned long clkslow = __raw_readl(S3C2410_CLKSLOW);
+	unsigned long orig = clkslow;
 
 	if (enable)
-		dclkcon |= clk->ctrlbit;
+		clkslow &= ~S3C2410_CLKSLOW_UCLK_OFF;
 	else
-		dclkcon &= ~clk->ctrlbit;
+		clkslow |= S3C2410_CLKSLOW_UCLK_OFF;
 
-	__raw_writel(dclkcon, S3C24XX_DCLKCON);
+	__raw_writel(clkslow, S3C2410_CLKSLOW);
 
-	return 0;
-}
+	/* if we started the UPLL, then allow to settle */
 
-static int s3c24xx_dclk_setparent(struct clk *clk, struct clk *parent)
-{
-	unsigned long dclkcon;
-	unsigned int uclk;
-
-	if (parent == &clk_upll)
-		uclk = 1;
-	else if (parent == &clk_p)
-		uclk = 0;
-	else
-		return -EINVAL;
-
-	clk->parent = parent;
-
-	dclkcon = __raw_readl(S3C24XX_DCLKCON);
-
-	if (clk->ctrlbit == S3C2410_DCLKCON_DCLK0EN) {
-		if (uclk)
-			dclkcon |= S3C2410_DCLKCON_DCLK0_UCLK;
-		else
-			dclkcon &= ~S3C2410_DCLKCON_DCLK0_UCLK;
-	} else {
-		if (uclk)
-			dclkcon |= S3C2410_DCLKCON_DCLK1_UCLK;
-		else
-			dclkcon &= ~S3C2410_DCLKCON_DCLK1_UCLK;
-	}
-
-	__raw_writel(dclkcon, S3C24XX_DCLKCON);
+	if (enable && (orig & S3C2410_CLKSLOW_UCLK_OFF))
+		udelay(200);
 
 	return 0;
 }
 
-
-static int s3c24xx_clkout_setparent(struct clk *clk, struct clk *parent)
-{
-	unsigned long mask;
-	unsigned long source;
-
-	/* calculate the MISCCR setting for the clock */
-
-	if (parent == &clk_xtal)
-		source = S3C2410_MISCCR_CLK0_MPLL;
-	else if (parent == &clk_upll)
-		source = S3C2410_MISCCR_CLK0_UPLL;
-	else if (parent == &clk_f)
-		source = S3C2410_MISCCR_CLK0_FCLK;
-	else if (parent == &clk_h)
-		source = S3C2410_MISCCR_CLK0_HCLK;
-	else if (parent == &clk_p)
-		source = S3C2410_MISCCR_CLK0_PCLK;
-	else if (clk == &s3c24xx_clkout0 && parent == &s3c24xx_dclk0)
-		source = S3C2410_MISCCR_CLK0_DCLK0;
-	else if (clk == &s3c24xx_clkout1 && parent == &s3c24xx_dclk1)
-		source = S3C2410_MISCCR_CLK0_DCLK0;
-	else
-		return -EINVAL;
-
-	clk->parent = parent;
-
-	if (clk == &s3c24xx_dclk0)
-		mask = S3C2410_MISCCR_CLK0_MASK;
-	else {
-		source <<= 4;
-		mask = S3C2410_MISCCR_CLK1_MASK;
+/* standard clock definitions */
+
+static struct clk init_clocks_disable[] = {
+	{
+		.name		= "nand",
+		.id		= -1,
+		.parent		= &clk_h,
+		.enable		= s3c2410_clkcon_enable,
+		.ctrlbit	= S3C2410_CLKCON_NAND,
+	}, {
+		.name		= "sdi",
+		.id		= -1,
+		.parent		= &clk_p,
+		.enable		= s3c2410_clkcon_enable,
+		.ctrlbit	= S3C2410_CLKCON_SDI,
+	}, {
+		.name		= "adc",
+		.id		= -1,
+		.parent		= &clk_p,
+		.enable		= s3c2410_clkcon_enable,
+		.ctrlbit	= S3C2410_CLKCON_ADC,
+	}, {
+		.name		= "i2c",
+		.id		= -1,
+		.parent		= &clk_p,
+		.enable		= s3c2410_clkcon_enable,
+		.ctrlbit	= S3C2410_CLKCON_IIC,
+	}, {
+		.name		= "iis",
+		.id		= -1,
+		.parent		= &clk_p,
+		.enable		= s3c2410_clkcon_enable,
+		.ctrlbit	= S3C2410_CLKCON_IIS,
+	}, {
+		.name		= "spi",
+		.id		= -1,
+		.parent		= &clk_p,
+		.enable		= s3c2410_clkcon_enable,
+		.ctrlbit	= S3C2410_CLKCON_SPI,
 	}
-
-	s3c2410_modify_misccr(mask, source);
-	return 0;
-}
-
-/* external clock definitions */
-
-struct clk s3c24xx_dclk0 = {
-	.name		= "dclk0",
-	.id		= -1,
-	.ctrlbit	= S3C2410_DCLKCON_DCLK0EN,
-	.enable	        = s3c24xx_dclk_enable,
-	.set_parent	= s3c24xx_dclk_setparent,
-};
-
-struct clk s3c24xx_dclk1 = {
-	.name		= "dclk1",
-	.id		= -1,
-	.ctrlbit	= S3C2410_DCLKCON_DCLK0EN,
-	.enable		= s3c24xx_dclk_enable,
-	.set_parent	= s3c24xx_dclk_setparent,
 };
 
-struct clk s3c24xx_clkout0 = {
-	.name		= "clkout0",
-	.id		= -1,
-	.set_parent	= s3c24xx_clkout_setparent,
+static struct clk init_clocks[] = {
+	{
+		.name		= "lcd",
+		.id		= -1,
+		.parent		= &clk_h,
+		.enable		= s3c2410_clkcon_enable,
+		.ctrlbit	= S3C2410_CLKCON_LCDC,
+	}, {
+		.name		= "gpio",
+		.id		= -1,
+		.parent		= &clk_p,
+		.enable		= s3c2410_clkcon_enable,
+		.ctrlbit	= S3C2410_CLKCON_GPIO,
+	}, {
+		.name		= "usb-host",
+		.id		= -1,
+		.parent		= &clk_h,
+		.enable		= s3c2410_clkcon_enable,
+		.ctrlbit	= S3C2410_CLKCON_USBH,
+	}, {
+		.name		= "usb-device",
+		.id		= -1,
+		.parent		= &clk_h,
+		.enable		= s3c2410_clkcon_enable,
+		.ctrlbit	= S3C2410_CLKCON_USBD,
+	}, {
+		.name		= "timers",
+		.id		= -1,
+		.parent		= &clk_p,
+		.enable		= s3c2410_clkcon_enable,
+		.ctrlbit	= S3C2410_CLKCON_PWMT,
+	}, {
+		.name		= "uart",
+		.id		= 0,
+		.parent		= &clk_p,
+		.enable		= s3c2410_clkcon_enable,
+		.ctrlbit	= S3C2410_CLKCON_UART0,
+	}, {
+		.name		= "uart",
+		.id		= 1,
+		.parent		= &clk_p,
+		.enable		= s3c2410_clkcon_enable,
+		.ctrlbit	= S3C2410_CLKCON_UART1,
+	}, {
+		.name		= "uart",
+		.id		= 2,
+		.parent		= &clk_p,
+		.enable		= s3c2410_clkcon_enable,
+		.ctrlbit	= S3C2410_CLKCON_UART2,
+	}, {
+		.name		= "rtc",
+		.id		= -1,
+		.parent		= &clk_p,
+		.enable		= s3c2410_clkcon_enable,
+		.ctrlbit	= S3C2410_CLKCON_RTC,
+	}, {
+		.name		= "watchdog",
+		.id		= -1,
+		.parent		= &clk_p,
+		.ctrlbit	= 0,
+	}, {
+		.name		= "usb-bus-host",
+		.id		= -1,
+		.parent		= &clk_usb_bus,
+	}, {
+		.name		= "usb-bus-gadget",
+		.id		= -1,
+		.parent		= &clk_usb_bus,
+	},
 };
 
-struct clk s3c24xx_clkout1 = {
-	.name		= "clkout1",
-	.id		= -1,
-	.set_parent	= s3c24xx_clkout_setparent,
-};
-
-struct clk s3c24xx_uclk = {
-	.name		= "uclk",
-	.id		= -1,
-};
-
-/* initialise the clock system */
-
-int s3c24xx_register_clock(struct clk *clk)
-{
-	clk->owner = THIS_MODULE;
-
-	if (clk->enable == NULL)
-		clk->enable = clk_null_enable;
-
-	/* add to the list of available clocks */
-
-	mutex_lock(&clocks_mutex);
-	list_add(&clk->list, &clocks);
-	mutex_unlock(&clocks_mutex);
-
-	return 0;
-}
-
-/* initalise all the clocks */
+/* s3c2410_baseclk_add()
+ *
+ * Add all the clocks used by the s3c2410 or compatible CPUs
+ * such as the S3C2440 and S3C2442.
+ *
+ * We cannot use a system device as we are needed before any
+ * of the init-calls that initialise the devices are actually
+ * done.
+*/
 
-int __init s3c24xx_setup_clocks(unsigned long xtal,
-				unsigned long fclk,
-				unsigned long hclk,
-				unsigned long pclk)
+int __init s3c2410_baseclk_add(void)
 {
-	printk(KERN_INFO "S3C24XX Clocks, (c) 2004 Simtec Electronics\n");
+	unsigned long clkslow = __raw_readl(S3C2410_CLKSLOW);
+	unsigned long clkcon  = __raw_readl(S3C2410_CLKCON);
+	struct clk *clkp;
+	struct clk *xtal;
+	int ret;
+	int ptr;
 
-	/* initialise the main system clocks */
+	clk_upll.enable = s3c2410_upll_enable;
 
-	clk_xtal.rate = xtal;
-	clk_upll.rate = s3c2410_get_pll(__raw_readl(S3C2410_UPLLCON), xtal);
+	if (s3c24xx_register_clock(&clk_usb_bus) < 0)
+		printk(KERN_ERR "failed to register usb bus clock\n");
 
-	clk_mpll.rate = fclk;
-	clk_h.rate = hclk;
-	clk_p.rate = pclk;
-	clk_f.rate = fclk;
+	/* register clocks from clock array */
 
-	/* assume uart clocks are correctly setup */
+	clkp = init_clocks;
+	for (ptr = 0; ptr < ARRAY_SIZE(init_clocks); ptr++, clkp++) {
+		/* ensure that we note the clock state */
 
-	/* register our clocks */
+		clkp->usage = clkcon & clkp->ctrlbit ? 1 : 0;
 
-	if (s3c24xx_register_clock(&clk_xtal) < 0)
-		printk(KERN_ERR "failed to register master xtal\n");
+		ret = s3c24xx_register_clock(clkp);
+		if (ret < 0) {
+			printk(KERN_ERR "Failed to register clock %s (%d)\n",
+			       clkp->name, ret);
+		}
+	}
 
-	if (s3c24xx_register_clock(&clk_mpll) < 0)
-		printk(KERN_ERR "failed to register mpll clock\n");
+	/* We must be careful disabling the clocks we are not intending to
+	 * be using at boot time, as subsytems such as the LCD which do
+	 * their own DMA requests to the bus can cause the system to lockup
+	 * if they where in the middle of requesting bus access.
+	 *
+	 * Disabling the LCD clock if the LCD is active is very dangerous,
+	 * and therefore the bootloader should be careful to not enable
+	 * the LCD clock if it is not needed.
+	*/
+
+	/* install (and disable) the clocks we do not need immediately */
+
+	clkp = init_clocks_disable;
+	for (ptr = 0; ptr < ARRAY_SIZE(init_clocks_disable); ptr++, clkp++) {
+
+		ret = s3c24xx_register_clock(clkp);
+		if (ret < 0) {
+			printk(KERN_ERR "Failed to register clock %s (%d)\n",
+			       clkp->name, ret);
+		}
 
-	if (s3c24xx_register_clock(&clk_upll) < 0)
-		printk(KERN_ERR "failed to register upll clock\n");
+		s3c2410_clkcon_enable(clkp, 0);
+	}
 
-	if (s3c24xx_register_clock(&clk_f) < 0)
-		printk(KERN_ERR "failed to register cpu fclk\n");
+	/* show the clock-slow value */
 
-	if (s3c24xx_register_clock(&clk_h) < 0)
-		printk(KERN_ERR "failed to register cpu hclk\n");
+	xtal = clk_get(NULL, "xtal");
 
-	if (s3c24xx_register_clock(&clk_p) < 0)
-		printk(KERN_ERR "failed to register cpu pclk\n");
+	printk("CLOCK: Slow mode (%ld.%ld MHz), %s, MPLL %s, UPLL %s\n",
+	       print_mhz(clk_get_rate(xtal) /
+			 ( 2 * S3C2410_CLKSLOW_GET_SLOWVAL(clkslow))),
+	       (clkslow & S3C2410_CLKSLOW_SLOW) ? "slow" : "fast",
+	       (clkslow & S3C2410_CLKSLOW_MPLL_OFF) ? "off" : "on",
+	       (clkslow & S3C2410_CLKSLOW_UCLK_OFF) ? "off" : "on");
 
 	return 0;
 }
diff --git a/arch/arm/mach-s3c2410/clock.h b/arch/arm/mach-s3c2410/clock.h
deleted file mode 100644
index 7f0ea03e1d4..00000000000
--- a/arch/arm/mach-s3c2410/clock.h
+++ /dev/null
@@ -1,63 +0,0 @@
-/*
- * linux/arch/arm/mach-s3c2410/clock.h
- *
- * Copyright (c) 2004-2005 Simtec Electronics
- *	http://www.simtec.co.uk/products/SWLINUX/
- *	Written by Ben Dooks, <ben@simtec.co.uk>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-struct clk {
-	struct list_head      list;
-	struct module        *owner;
-	struct clk           *parent;
-	const char           *name;
-	int		      id;
-	int		      usage;
-	unsigned long         rate;
-	unsigned long         ctrlbit;
-
-	int		    (*enable)(struct clk *, int enable);
-	int		    (*set_rate)(struct clk *c, unsigned long rate);
-	unsigned long	    (*get_rate)(struct clk *c);
-	unsigned long	    (*round_rate)(struct clk *c, unsigned long rate);
-	int		    (*set_parent)(struct clk *c, struct clk *parent);
-};
-
-/* other clocks which may be registered by board support */
-
-extern struct clk s3c24xx_dclk0;
-extern struct clk s3c24xx_dclk1;
-extern struct clk s3c24xx_clkout0;
-extern struct clk s3c24xx_clkout1;
-extern struct clk s3c24xx_uclk;
-
-extern struct clk clk_usb_bus;
-
-/* core clock support */
-
-extern struct clk clk_f;
-extern struct clk clk_h;
-extern struct clk clk_p;
-extern struct clk clk_mpll;
-extern struct clk clk_upll;
-extern struct clk clk_xtal;
-
-/* exports for arch/arm/mach-s3c2410
- *
- * Please DO NOT use these outside of arch/arm/mach-s3c2410
-*/
-
-extern struct mutex clocks_mutex;
-
-extern int s3c2410_clkcon_enable(struct clk *clk, int enable);
-
-extern int s3c24xx_register_clock(struct clk *clk);
-
-extern int s3c24xx_setup_clocks(unsigned long xtal,
-				unsigned long fclk,
-				unsigned long hclk,
-				unsigned long pclk);
diff --git a/arch/arm/mach-s3c2410/common-smdk.h b/arch/arm/mach-s3c2410/common-smdk.h
deleted file mode 100644
index 0e3a3be330a..00000000000
--- a/arch/arm/mach-s3c2410/common-smdk.h
+++ /dev/null
@@ -1,15 +0,0 @@
-/* linux/arch/arm/mach-s3c2410/common-smdk.h
- *
- * Copyright (c) 2006 Simtec Electronics
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * Common code for SMDK2410 and SMDK2440 boards
- *
- * http://www.fluff.org/ben/smdk2440/
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-extern void smdk_machine_init(void);
diff --git a/arch/arm/mach-s3c2410/cpu.h b/arch/arm/mach-s3c2410/cpu.h
deleted file mode 100644
index be42e4032a6..00000000000
--- a/arch/arm/mach-s3c2410/cpu.h
+++ /dev/null
@@ -1,69 +0,0 @@
-/* arch/arm/mach-s3c2410/cpu.h
- *
- * Copyright (c) 2004-2005 Simtec Electronics
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * Header file for S3C24XX CPU support
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-/* todo - fix when rmk changes iodescs to use `void __iomem *` */
-
-#define IODESC_ENT(x) { (unsigned long)S3C24XX_VA_##x, __phys_to_pfn(S3C24XX_PA_##x), S3C24XX_SZ_##x, MT_DEVICE }
-
-#ifndef MHZ
-#define MHZ (1000*1000)
-#endif
-
-#define print_mhz(m) ((m) / MHZ), ((m / 1000) % 1000)
-
-/* forward declaration */
-struct s3c24xx_uart_resources;
-struct platform_device;
-struct s3c2410_uartcfg;
-struct map_desc;
-
-/* core initialisation functions */
-
-extern void s3c24xx_init_irq(void);
-
-extern void s3c24xx_init_io(struct map_desc *mach_desc, int size);
-
-extern void s3c24xx_init_uarts(struct s3c2410_uartcfg *cfg, int no);
-
-extern void s3c24xx_init_clocks(int xtal);
-
-extern void s3c24xx_init_uartdevs(char *name,
-				  struct s3c24xx_uart_resources *res,
-				  struct s3c2410_uartcfg *cfg, int no);
-
-/* the board structure is used at first initialsation time
- * to get info such as the devices to register for this
- * board. This is done because platfrom_add_devices() cannot
- * be called from the map_io entry.
-*/
-
-struct s3c24xx_board {
-	struct platform_device  **devices;
-	unsigned int              devices_count;
-
-	struct clk		**clocks;
-	unsigned int		  clocks_count;
-};
-
-extern void s3c24xx_set_board(struct s3c24xx_board *board);
-
-/* timer for 2410/2440 */
-
-struct sys_timer;
-extern struct sys_timer s3c24xx_timer;
-
-/* system device classes */
-
-extern struct sysdev_class s3c2410_sysclass;
-extern struct sysdev_class s3c2412_sysclass;
-extern struct sysdev_class s3c2440_sysclass;
-extern struct sysdev_class s3c2442_sysclass;
diff --git a/arch/arm/mach-s3c2410/devs.h b/arch/arm/mach-s3c2410/devs.h
deleted file mode 100644
index 14fb0bade71..00000000000
--- a/arch/arm/mach-s3c2410/devs.h
+++ /dev/null
@@ -1,51 +0,0 @@
-/* arch/arm/mach-s3c2410/devs.h
- *
- * Copyright (c) 2004 Simtec Electronics
- * Ben Dooks <ben@simtec.co.uk>
- *
- * Header file for s3c2410 standard platform devices
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-#include <linux/platform_device.h>
-
-struct s3c24xx_uart_resources {
-	struct resource		*resources;
-	unsigned long		 nr_resources;
-};
-
-extern struct s3c24xx_uart_resources s3c2410_uart_resources[];
-
-extern struct platform_device *s3c24xx_uart_devs[];
-extern struct platform_device *s3c24xx_uart_src[];
-
-extern struct platform_device s3c_device_usb;
-extern struct platform_device s3c_device_lcd;
-extern struct platform_device s3c_device_wdt;
-extern struct platform_device s3c_device_i2c;
-extern struct platform_device s3c_device_iis;
-extern struct platform_device s3c_device_rtc;
-extern struct platform_device s3c_device_adc;
-extern struct platform_device s3c_device_sdi;
-
-extern struct platform_device s3c_device_spi0;
-extern struct platform_device s3c_device_spi1;
-
-extern struct platform_device s3c_device_nand;
-
-extern struct platform_device s3c_device_timer0;
-extern struct platform_device s3c_device_timer1;
-extern struct platform_device s3c_device_timer2;
-extern struct platform_device s3c_device_timer3;
-
-extern struct platform_device s3c_device_usbgadget;
-
-/* s3c2440 specific devices */
-
-#ifdef CONFIG_CPU_S3C2440
-
-extern struct platform_device s3c_device_camif;
-
-#endif
diff --git a/arch/arm/mach-s3c2410/dma.c b/arch/arm/mach-s3c2410/dma.c
index fa860e716b4..67d1ad36397 100644
--- a/arch/arm/mach-s3c2410/dma.c
+++ b/arch/arm/mach-s3c2410/dma.c
@@ -1,9 +1,9 @@
 /* linux/arch/arm/mach-s3c2410/dma.c
  *
- * Copyright (c) 2003-2005,2006 Simtec Electronics
+ * Copyright (c) 2006 Simtec Electronics
  *	Ben Dooks <ben@simtec.co.uk>
  *
- * S3C2410 DMA core
+ * S3C2410 DMA selection
  *
  * http://armlinux.simtec.co.uk/
  *
@@ -12,1430 +12,170 @@
  * published by the Free Software Foundation.
 */
 
-
-#ifdef CONFIG_S3C2410_DMA_DEBUG
-#define DEBUG
-#endif
-
-#include <linux/module.h>
+#include <linux/kernel.h>
 #include <linux/init.h>
-#include <linux/sched.h>
-#include <linux/spinlock.h>
-#include <linux/interrupt.h>
 #include <linux/sysdev.h>
-#include <linux/slab.h>
-#include <linux/errno.h>
-#include <linux/delay.h>
+#include <linux/serial_core.h>
 
-#include <asm/system.h>
-#include <asm/irq.h>
-#include <asm/hardware.h>
-#include <asm/io.h>
 #include <asm/dma.h>
-
-#include <asm/mach/dma.h>
-#include <asm/arch/map.h>
-
-#include "dma.h"
-
-/* io map for dma */
-static void __iomem *dma_base;
-static struct kmem_cache *dma_kmem;
-
-struct s3c24xx_dma_selection dma_sel;
-
-/* dma channel state information */
-struct s3c2410_dma_chan s3c2410_chans[S3C2410_DMA_CHANNELS];
-
-/* debugging functions */
-
-#define BUF_MAGIC (0xcafebabe)
-
-#define dmawarn(fmt...) printk(KERN_DEBUG fmt)
-
-#define dma_regaddr(chan, reg) ((chan)->regs + (reg))
-
-#if 1
-#define dma_wrreg(chan, reg, val) writel((val), (chan)->regs + (reg))
-#else
-static inline void
-dma_wrreg(struct s3c2410_dma_chan *chan, int reg, unsigned long val)
-{
-	pr_debug("writing %08x to register %08x\n",(unsigned int)val,reg);
-	writel(val, dma_regaddr(chan, reg));
-}
-#endif
-
-#define dma_rdreg(chan, reg) readl((chan)->regs + (reg))
-
-/* captured register state for debug */
-
-struct s3c2410_dma_regstate {
-	unsigned long         dcsrc;
-	unsigned long         disrc;
-	unsigned long         dstat;
-	unsigned long         dcon;
-	unsigned long         dmsktrig;
+#include <asm/arch/dma.h>
+
+#include <asm/plat-s3c24xx/cpu.h>
+#include <asm/plat-s3c24xx/dma.h>
+
+#include <asm/arch/regs-serial.h>
+#include <asm/arch/regs-gpio.h>
+#include <asm/arch/regs-ac97.h>
+#include <asm/arch/regs-mem.h>
+#include <asm/arch/regs-lcd.h>
+#include <asm/arch/regs-sdi.h>
+#include <asm/arch/regs-iis.h>
+#include <asm/arch/regs-spi.h>
+
+static struct s3c24xx_dma_map __initdata s3c2410_dma_mappings[] = {
+	[DMACH_XD0] = {
+		.name		= "xdreq0",
+		.channels[0]	= S3C2410_DCON_CH0_XDREQ0 | DMA_CH_VALID,
+	},
+	[DMACH_XD1] = {
+		.name		= "xdreq1",
+		.channels[1]	= S3C2410_DCON_CH1_XDREQ1 | DMA_CH_VALID,
+	},
+	[DMACH_SDI] = {
+		.name		= "sdi",
+		.channels[0]	= S3C2410_DCON_CH0_SDI | DMA_CH_VALID,
+		.channels[2]	= S3C2410_DCON_CH2_SDI | DMA_CH_VALID,
+		.channels[3]	= S3C2410_DCON_CH3_SDI | DMA_CH_VALID,
+		.hw_addr.to	= S3C2410_PA_IIS + S3C2410_IISFIFO,
+		.hw_addr.from	= S3C2410_PA_IIS + S3C2410_IISFIFO,
+	},
+	[DMACH_SPI0] = {
+		.name		= "spi0",
+		.channels[1]	= S3C2410_DCON_CH1_SPI | DMA_CH_VALID,
+		.hw_addr.to	= S3C2410_PA_SPI + S3C2410_SPTDAT,
+		.hw_addr.from	= S3C2410_PA_SPI + S3C2410_SPRDAT,
+	},
+	[DMACH_SPI1] = {
+		.name		= "spi1",
+		.channels[3]	= S3C2410_DCON_CH3_SPI | DMA_CH_VALID,
+		.hw_addr.to	= S3C2410_PA_SPI + 0x20 + S3C2410_SPTDAT,
+		.hw_addr.from	= S3C2410_PA_SPI + 0x20 + S3C2410_SPRDAT,
+	},
+	[DMACH_UART0] = {
+		.name		= "uart0",
+		.channels[0]	= S3C2410_DCON_CH0_UART0 | DMA_CH_VALID,
+		.hw_addr.to	= S3C2410_PA_UART0 + S3C2410_UTXH,
+		.hw_addr.from	= S3C2410_PA_UART0 + S3C2410_URXH,
+	},
+	[DMACH_UART1] = {
+		.name		= "uart1",
+		.channels[1]	= S3C2410_DCON_CH1_UART1 | DMA_CH_VALID,
+		.hw_addr.to	= S3C2410_PA_UART1 + S3C2410_UTXH,
+		.hw_addr.from	= S3C2410_PA_UART1 + S3C2410_URXH,
+	},
+      	[DMACH_UART2] = {
+		.name		= "uart2",
+		.channels[3]	= S3C2410_DCON_CH3_UART2 | DMA_CH_VALID,
+		.hw_addr.to	= S3C2410_PA_UART2 + S3C2410_UTXH,
+		.hw_addr.from	= S3C2410_PA_UART2 + S3C2410_URXH,
+	},
+	[DMACH_TIMER] = {
+		.name		= "timer",
+		.channels[0]	= S3C2410_DCON_CH0_TIMER | DMA_CH_VALID,
+		.channels[2]	= S3C2410_DCON_CH2_TIMER | DMA_CH_VALID,
+		.channels[3]	= S3C2410_DCON_CH3_TIMER | DMA_CH_VALID,
+	},
+	[DMACH_I2S_IN] = {
+		.name		= "i2s-sdi",
+		.channels[1]	= S3C2410_DCON_CH1_I2SSDI | DMA_CH_VALID,
+		.channels[2]	= S3C2410_DCON_CH2_I2SSDI | DMA_CH_VALID,
+		.hw_addr.from	= S3C2410_PA_IIS + S3C2410_IISFIFO,
+	},
+	[DMACH_I2S_OUT] = {
+		.name		= "i2s-sdo",
+		.channels[2]	= S3C2410_DCON_CH2_I2SSDO | DMA_CH_VALID,
+		.hw_addr.to	= S3C2410_PA_IIS + S3C2410_IISFIFO,
+	},
+	[DMACH_USB_EP1] = {
+		.name		= "usb-ep1",
+		.channels[0]	= S3C2410_DCON_CH0_USBEP1 | DMA_CH_VALID,
+	},
+	[DMACH_USB_EP2] = {
+		.name		= "usb-ep2",
+		.channels[1]	= S3C2410_DCON_CH1_USBEP2 | DMA_CH_VALID,
+	},
+	[DMACH_USB_EP3] = {
+		.name		= "usb-ep3",
+		.channels[2]	= S3C2410_DCON_CH2_USBEP3 | DMA_CH_VALID,
+	},
+	[DMACH_USB_EP4] = {
+		.name		= "usb-ep4",
+		.channels[3]	=S3C2410_DCON_CH3_USBEP4 | DMA_CH_VALID,
+	},
 };
 
-#ifdef CONFIG_S3C2410_DMA_DEBUG
-
-/* dmadbg_showregs
- *
- * simple debug routine to print the current state of the dma registers
-*/
-
-static void
-dmadbg_capture(struct s3c2410_dma_chan *chan, struct s3c2410_dma_regstate *regs)
-{
-	regs->dcsrc    = dma_rdreg(chan, S3C2410_DMA_DCSRC);
-	regs->disrc    = dma_rdreg(chan, S3C2410_DMA_DISRC);
-	regs->dstat    = dma_rdreg(chan, S3C2410_DMA_DSTAT);
-	regs->dcon     = dma_rdreg(chan, S3C2410_DMA_DCON);
-	regs->dmsktrig = dma_rdreg(chan, S3C2410_DMA_DMASKTRIG);
-}
-
-static void
-dmadbg_dumpregs(const char *fname, int line, struct s3c2410_dma_chan *chan,
-		 struct s3c2410_dma_regstate *regs)
-{
-	printk(KERN_DEBUG "dma%d: %s:%d: DCSRC=%08lx, DISRC=%08lx, DSTAT=%08lx DMT=%02lx, DCON=%08lx\n",
-	       chan->number, fname, line,
-	       regs->dcsrc, regs->disrc, regs->dstat, regs->dmsktrig,
-	       regs->dcon);
-}
-
-static void
-dmadbg_showchan(const char *fname, int line, struct s3c2410_dma_chan *chan)
-{
-	struct s3c2410_dma_regstate state;
-
-	dmadbg_capture(chan, &state);
-
-	printk(KERN_DEBUG "dma%d: %s:%d: ls=%d, cur=%p, %p %p\n",
-	       chan->number, fname, line, chan->load_state,
-	       chan->curr, chan->next, chan->end);
-
-	dmadbg_dumpregs(fname, line, chan, &state);
-}
-
-static void
-dmadbg_showregs(const char *fname, int line, struct s3c2410_dma_chan *chan)
-{
-	struct s3c2410_dma_regstate state;
-
-	dmadbg_capture(chan, &state);
-	dmadbg_dumpregs(fname, line, chan, &state);
-}
-
-#define dbg_showregs(chan) dmadbg_showregs(__FUNCTION__, __LINE__, (chan))
-#define dbg_showchan(chan) dmadbg_showchan(__FUNCTION__, __LINE__, (chan))
-#else
-#define dbg_showregs(chan) do { } while(0)
-#define dbg_showchan(chan) do { } while(0)
-#endif /* CONFIG_S3C2410_DMA_DEBUG */
-
-static struct s3c2410_dma_chan *dma_chan_map[DMACH_MAX];
-
-/* lookup_dma_channel
- *
- * change the dma channel number given into a real dma channel id
-*/
-
-static struct s3c2410_dma_chan *lookup_dma_channel(unsigned int channel)
-{
-	if (channel & DMACH_LOW_LEVEL)
-		return &s3c2410_chans[channel & ~DMACH_LOW_LEVEL];
-	else
-		return dma_chan_map[channel];
-}
-
-/* s3c2410_dma_stats_timeout
- *
- * Update DMA stats from timeout info
-*/
-
-static void
-s3c2410_dma_stats_timeout(struct s3c2410_dma_stats *stats, int val)
+static void s3c2410_dma_select(struct s3c2410_dma_chan *chan,
+			       struct s3c24xx_dma_map *map)
 {
-	if (stats == NULL)
-		return;
-
-	if (val > stats->timeout_longest)
-		stats->timeout_longest = val;
-	if (val < stats->timeout_shortest)
-		stats->timeout_shortest = val;
-
-	stats->timeout_avg += val;
+	chan->dcon = map->channels[chan->number] & ~DMA_CH_VALID;
 }
 
-/* s3c2410_dma_waitforload
- *
- * wait for the DMA engine to load a buffer, and update the state accordingly
-*/
-
-static int
-s3c2410_dma_waitforload(struct s3c2410_dma_chan *chan, int line)
-{
-	int timeout = chan->load_timeout;
-	int took;
-
-	if (chan->load_state != S3C2410_DMALOAD_1LOADED) {
-		printk(KERN_ERR "dma%d: s3c2410_dma_waitforload() called in loadstate %d from line %d\n", chan->number, chan->load_state, line);
-		return 0;
-	}
-
-	if (chan->stats != NULL)
-		chan->stats->loads++;
-
-	while (--timeout > 0) {
-		if ((dma_rdreg(chan, S3C2410_DMA_DSTAT) << (32-20)) != 0) {
-			took = chan->load_timeout - timeout;
-
-			s3c2410_dma_stats_timeout(chan->stats, took);
-
-			switch (chan->load_state) {
-			case S3C2410_DMALOAD_1LOADED:
-				chan->load_state = S3C2410_DMALOAD_1RUNNING;
-				break;
-
-			default:
-				printk(KERN_ERR "dma%d: unknown load_state in s3c2410_dma_waitforload() %d\n", chan->number, chan->load_state);
-			}
-
-			return 1;
-		}
-	}
-
-	if (chan->stats != NULL) {
-		chan->stats->timeout_failed++;
-	}
-
-	return 0;
-}
-
-
-
-/* s3c2410_dma_loadbuffer
- *
- * load a buffer, and update the channel state
-*/
-
-static inline int
-s3c2410_dma_loadbuffer(struct s3c2410_dma_chan *chan,
-		       struct s3c2410_dma_buf *buf)
-{
-	unsigned long reload;
-
-	pr_debug("s3c2410_chan_loadbuffer: loading buff %p (0x%08lx,0x%06x)\n",
-		 buf, (unsigned long)buf->data, buf->size);
-
-	if (buf == NULL) {
-		dmawarn("buffer is NULL\n");
-		return -EINVAL;
-	}
-
-	/* check the state of the channel before we do anything */
-
-	if (chan->load_state == S3C2410_DMALOAD_1LOADED) {
-		dmawarn("load_state is S3C2410_DMALOAD_1LOADED\n");
-	}
-
-	if (chan->load_state == S3C2410_DMALOAD_1LOADED_1RUNNING) {
-		dmawarn("state is S3C2410_DMALOAD_1LOADED_1RUNNING\n");
-	}
-
-	/* it would seem sensible if we are the last buffer to not bother
-	 * with the auto-reload bit, so that the DMA engine will not try
-	 * and load another transfer after this one has finished...
-	 */
-	if (chan->load_state == S3C2410_DMALOAD_NONE) {
-		pr_debug("load_state is none, checking for noreload (next=%p)\n",
-			 buf->next);
-		reload = (buf->next == NULL) ? S3C2410_DCON_NORELOAD : 0;
-	} else {
-		//pr_debug("load_state is %d => autoreload\n", chan->load_state);
-		reload = S3C2410_DCON_AUTORELOAD;
-	}
-
-	if ((buf->data & 0xf0000000) != 0x30000000) {
-		dmawarn("dmaload: buffer is %p\n", (void *)buf->data);
-	}
-
-	writel(buf->data, chan->addr_reg);
-
-	dma_wrreg(chan, S3C2410_DMA_DCON,
-		  chan->dcon | reload | (buf->size/chan->xfer_unit));
-
-	chan->next = buf->next;
-
-	/* update the state of the channel */
-
-	switch (chan->load_state) {
-	case S3C2410_DMALOAD_NONE:
-		chan->load_state = S3C2410_DMALOAD_1LOADED;
-		break;
-
-	case S3C2410_DMALOAD_1RUNNING:
-		chan->load_state = S3C2410_DMALOAD_1LOADED_1RUNNING;
-		break;
-
-	default:
-		dmawarn("dmaload: unknown state %d in loadbuffer\n",
-			chan->load_state);
-		break;
-	}
-
-	return 0;
-}
-
-/* s3c2410_dma_call_op
- *
- * small routine to call the op routine with the given op if it has been
- * registered
-*/
-
-static void
-s3c2410_dma_call_op(struct s3c2410_dma_chan *chan, enum s3c2410_chan_op op)
-{
-	if (chan->op_fn != NULL) {
-		(chan->op_fn)(chan, op);
-	}
-}
-
-/* s3c2410_dma_buffdone
- *
- * small wrapper to check if callback routine needs to be called, and
- * if so, call it
-*/
-
-static inline void
-s3c2410_dma_buffdone(struct s3c2410_dma_chan *chan, struct s3c2410_dma_buf *buf,
-		     enum s3c2410_dma_buffresult result)
-{
-#if 0
-	pr_debug("callback_fn=%p, buf=%p, id=%p, size=%d, result=%d\n",
-		 chan->callback_fn, buf, buf->id, buf->size, result);
-#endif
-
-	if (chan->callback_fn != NULL) {
-		(chan->callback_fn)(chan, buf->id, buf->size, result);
-	}
-}
-
-/* s3c2410_dma_start
- *
- * start a dma channel going
-*/
-
-static int s3c2410_dma_start(struct s3c2410_dma_chan *chan)
-{
-	unsigned long tmp;
-	unsigned long flags;
-
-	pr_debug("s3c2410_start_dma: channel=%d\n", chan->number);
-
-	local_irq_save(flags);
-
-	if (chan->state == S3C2410_DMA_RUNNING) {
-		pr_debug("s3c2410_start_dma: already running (%d)\n", chan->state);
-		local_irq_restore(flags);
-		return 0;
-	}
-
-	chan->state = S3C2410_DMA_RUNNING;
-
-	/* check wether there is anything to load, and if not, see
-	 * if we can find anything to load
-	 */
-
-	if (chan->load_state == S3C2410_DMALOAD_NONE) {
-		if (chan->next == NULL) {
-			printk(KERN_ERR "dma%d: channel has nothing loaded\n",
-			       chan->number);
-			chan->state = S3C2410_DMA_IDLE;
-			local_irq_restore(flags);
-			return -EINVAL;
-		}
-
-		s3c2410_dma_loadbuffer(chan, chan->next);
-	}
-
-	dbg_showchan(chan);
-
-	/* enable the channel */
-
-	if (!chan->irq_enabled) {
-		enable_irq(chan->irq);
-		chan->irq_enabled = 1;
-	}
-
-	/* start the channel going */
-
-	tmp = dma_rdreg(chan, S3C2410_DMA_DMASKTRIG);
-	tmp &= ~S3C2410_DMASKTRIG_STOP;
-	tmp |= S3C2410_DMASKTRIG_ON;
-	dma_wrreg(chan, S3C2410_DMA_DMASKTRIG, tmp);
-
-	pr_debug("dma%d: %08lx to DMASKTRIG\n", chan->number, tmp);
-
-#if 0
-	/* the dma buffer loads should take care of clearing the AUTO
-	 * reloading feature */
-	tmp = dma_rdreg(chan, S3C2410_DMA_DCON);
-	tmp &= ~S3C2410_DCON_NORELOAD;
-	dma_wrreg(chan, S3C2410_DMA_DCON, tmp);
-#endif
-
-	s3c2410_dma_call_op(chan, S3C2410_DMAOP_START);
-
-	dbg_showchan(chan);
-
-	/* if we've only loaded one buffer onto the channel, then chec
-	 * to see if we have another, and if so, try and load it so when
-	 * the first buffer is finished, the new one will be loaded onto
-	 * the channel */
-
-	if (chan->next != NULL) {
-		if (chan->load_state == S3C2410_DMALOAD_1LOADED) {
-
-			if (s3c2410_dma_waitforload(chan, __LINE__) == 0) {
-				pr_debug("%s: buff not yet loaded, no more todo\n",
-					 __FUNCTION__);
-			} else {
-				chan->load_state = S3C2410_DMALOAD_1RUNNING;
-				s3c2410_dma_loadbuffer(chan, chan->next);
-			}
-
-		} else if (chan->load_state == S3C2410_DMALOAD_1RUNNING) {
-			s3c2410_dma_loadbuffer(chan, chan->next);
-		}
-	}
-
-
-	local_irq_restore(flags);
-
-	return 0;
-}
-
-/* s3c2410_dma_canload
- *
- * work out if we can queue another buffer into the DMA engine
-*/
-
-static int
-s3c2410_dma_canload(struct s3c2410_dma_chan *chan)
-{
-	if (chan->load_state == S3C2410_DMALOAD_NONE ||
-	    chan->load_state == S3C2410_DMALOAD_1RUNNING)
-		return 1;
-
-	return 0;
-}
-
-/* s3c2410_dma_enqueue
- *
- * queue an given buffer for dma transfer.
- *
- * id         the device driver's id information for this buffer
- * data       the physical address of the buffer data
- * size       the size of the buffer in bytes
- *
- * If the channel is not running, then the flag S3C2410_DMAF_AUTOSTART
- * is checked, and if set, the channel is started. If this flag isn't set,
- * then an error will be returned.
- *
- * It is possible to queue more than one DMA buffer onto a channel at
- * once, and the code will deal with the re-loading of the next buffer
- * when necessary.
-*/
-
-int s3c2410_dma_enqueue(unsigned int channel, void *id,
-			dma_addr_t data, int size)
-{
-	struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
-	struct s3c2410_dma_buf *buf;
-	unsigned long flags;
-
-	if (chan == NULL)
-		return -EINVAL;
-
-	pr_debug("%s: id=%p, data=%08x, size=%d\n",
-		 __FUNCTION__, id, (unsigned int)data, size);
-
-	buf = kmem_cache_alloc(dma_kmem, GFP_ATOMIC);
-	if (buf == NULL) {
-		pr_debug("%s: out of memory (%ld alloc)\n",
-			 __FUNCTION__, (long)sizeof(*buf));
-		return -ENOMEM;
-	}
-
-	//pr_debug("%s: new buffer %p\n", __FUNCTION__, buf);
-	//dbg_showchan(chan);
-
-	buf->next  = NULL;
-	buf->data  = buf->ptr = data;
-	buf->size  = size;
-	buf->id    = id;
-	buf->magic = BUF_MAGIC;
-
-	local_irq_save(flags);
-
-	if (chan->curr == NULL) {
-		/* we've got nothing loaded... */
-		pr_debug("%s: buffer %p queued onto empty channel\n",
-			 __FUNCTION__, buf);
-
-		chan->curr = buf;
-		chan->end  = buf;
-		chan->next = NULL;
-	} else {
-		pr_debug("dma%d: %s: buffer %p queued onto non-empty channel\n",
-			 chan->number, __FUNCTION__, buf);
-
-		if (chan->end == NULL)
-			pr_debug("dma%d: %s: %p not empty, and chan->end==NULL?\n",
-				 chan->number, __FUNCTION__, chan);
-
-		chan->end->next = buf;
-		chan->end = buf;
-	}
-
-	/* if necessary, update the next buffer field */
-	if (chan->next == NULL)
-		chan->next = buf;
-
-	/* check to see if we can load a buffer */
-	if (chan->state == S3C2410_DMA_RUNNING) {
-		if (chan->load_state == S3C2410_DMALOAD_1LOADED && 1) {
-			if (s3c2410_dma_waitforload(chan, __LINE__) == 0) {
-				printk(KERN_ERR "dma%d: loadbuffer:"
-				       "timeout loading buffer\n",
-				       chan->number);
-				dbg_showchan(chan);
-				local_irq_restore(flags);
-				return -EINVAL;
-			}
-		}
-
-		while (s3c2410_dma_canload(chan) && chan->next != NULL) {
-			s3c2410_dma_loadbuffer(chan, chan->next);
-		}
-	} else if (chan->state == S3C2410_DMA_IDLE) {
-		if (chan->flags & S3C2410_DMAF_AUTOSTART) {
-			s3c2410_dma_ctrl(chan->number, S3C2410_DMAOP_START);
-		}
-	}
-
-	local_irq_restore(flags);
-	return 0;
-}
-
-EXPORT_SYMBOL(s3c2410_dma_enqueue);
-
-static inline void
-s3c2410_dma_freebuf(struct s3c2410_dma_buf *buf)
-{
-	int magicok = (buf->magic == BUF_MAGIC);
-
-	buf->magic = -1;
-
-	if (magicok) {
-		kmem_cache_free(dma_kmem, buf);
-	} else {
-		printk("s3c2410_dma_freebuf: buff %p with bad magic\n", buf);
-	}
-}
-
-/* s3c2410_dma_lastxfer
- *
- * called when the system is out of buffers, to ensure that the channel
- * is prepared for shutdown.
-*/
-
-static inline void
-s3c2410_dma_lastxfer(struct s3c2410_dma_chan *chan)
-{
-#if 0
-	pr_debug("dma%d: s3c2410_dma_lastxfer: load_state %d\n",
-		 chan->number, chan->load_state);
-#endif
-
-	switch (chan->load_state) {
-	case S3C2410_DMALOAD_NONE:
-		break;
-
-	case S3C2410_DMALOAD_1LOADED:
-		if (s3c2410_dma_waitforload(chan, __LINE__) == 0) {
-				/* flag error? */
-			printk(KERN_ERR "dma%d: timeout waiting for load (%s)\n",
-			       chan->number, __FUNCTION__);
-			return;
-		}
-		break;
-
-	case S3C2410_DMALOAD_1LOADED_1RUNNING:
-		/* I belive in this case we do not have anything to do
-		 * until the next buffer comes along, and we turn off the
-		 * reload */
-		return;
-
-	default:
-		pr_debug("dma%d: lastxfer: unhandled load_state %d with no next\n",
-			 chan->number, chan->load_state);
-		return;
-
-	}
-
-	/* hopefully this'll shut the damned thing up after the transfer... */
-	dma_wrreg(chan, S3C2410_DMA_DCON, chan->dcon | S3C2410_DCON_NORELOAD);
-}
-
-
-#define dmadbg2(x...)
-
-static irqreturn_t
-s3c2410_dma_irq(int irq, void *devpw)
-{
-	struct s3c2410_dma_chan *chan = (struct s3c2410_dma_chan *)devpw;
-	struct s3c2410_dma_buf  *buf;
-
-	buf = chan->curr;
-
-	dbg_showchan(chan);
-
-	/* modify the channel state */
-
-	switch (chan->load_state) {
-	case S3C2410_DMALOAD_1RUNNING:
-		/* TODO - if we are running only one buffer, we probably
-		 * want to reload here, and then worry about the buffer
-		 * callback */
-
-		chan->load_state = S3C2410_DMALOAD_NONE;
-		break;
-
-	case S3C2410_DMALOAD_1LOADED:
-		/* iirc, we should go back to NONE loaded here, we
-		 * had a buffer, and it was never verified as being
-		 * loaded.
-		 */
-
-		chan->load_state = S3C2410_DMALOAD_NONE;
-		break;
-
-	case S3C2410_DMALOAD_1LOADED_1RUNNING:
-		/* we'll worry about checking to see if another buffer is
-		 * ready after we've called back the owner. This should
-		 * ensure we do not wait around too long for the DMA
-		 * engine to start the next transfer
-		 */
-
-		chan->load_state = S3C2410_DMALOAD_1LOADED;
-		break;
-
-	case S3C2410_DMALOAD_NONE:
-		printk(KERN_ERR "dma%d: IRQ with no loaded buffer?\n",
-		       chan->number);
-		break;
-
-	default:
-		printk(KERN_ERR "dma%d: IRQ in invalid load_state %d\n",
-		       chan->number, chan->load_state);
-		break;
-	}
-
-	if (buf != NULL) {
-		/* update the chain to make sure that if we load any more
-		 * buffers when we call the callback function, things should
-		 * work properly */
-
-		chan->curr = buf->next;
-		buf->next  = NULL;
-
-		if (buf->magic != BUF_MAGIC) {
-			printk(KERN_ERR "dma%d: %s: buf %p incorrect magic\n",
-			       chan->number, __FUNCTION__, buf);
-			return IRQ_HANDLED;
-		}
-
-		s3c2410_dma_buffdone(chan, buf, S3C2410_RES_OK);
-
-		/* free resouces */
-		s3c2410_dma_freebuf(buf);
-	} else {
-	}
-
-	/* only reload if the channel is still running... our buffer done
-	 * routine may have altered the state by requesting the dma channel
-	 * to stop or shutdown... */
-
-	/* todo: check that when the channel is shut-down from inside this
-	 * function, we cope with unsetting reload, etc */
-
-	if (chan->next != NULL && chan->state != S3C2410_DMA_IDLE) {
-		unsigned long flags;
-
-		switch (chan->load_state) {
-		case S3C2410_DMALOAD_1RUNNING:
-			/* don't need to do anything for this state */
-			break;
-
-		case S3C2410_DMALOAD_NONE:
-			/* can load buffer immediately */
-			break;
-
-		case S3C2410_DMALOAD_1LOADED:
-			if (s3c2410_dma_waitforload(chan, __LINE__) == 0) {
-				/* flag error? */
-				printk(KERN_ERR "dma%d: timeout waiting for load (%s)\n",
-				       chan->number, __FUNCTION__);
-				return IRQ_HANDLED;
-			}
-
-			break;
-
-		case S3C2410_DMALOAD_1LOADED_1RUNNING:
-			goto no_load;
-
-		default:
-			printk(KERN_ERR "dma%d: unknown load_state in irq, %d\n",
-			       chan->number, chan->load_state);
-			return IRQ_HANDLED;
-		}
-
-		local_irq_save(flags);
-		s3c2410_dma_loadbuffer(chan, chan->next);
-		local_irq_restore(flags);
-	} else {
-		s3c2410_dma_lastxfer(chan);
-
-		/* see if we can stop this channel.. */
-		if (chan->load_state == S3C2410_DMALOAD_NONE) {
-			pr_debug("dma%d: end of transfer, stopping channel (%ld)\n",
-				 chan->number, jiffies);
-			s3c2410_dma_ctrl(chan->number | DMACH_LOW_LEVEL,
-					 S3C2410_DMAOP_STOP);
-		}
-	}
-
- no_load:
-	return IRQ_HANDLED;
-}
-
-static struct s3c2410_dma_chan *s3c2410_dma_map_channel(int channel);
-
-/* s3c2410_request_dma
- *
- * get control of an dma channel
-*/
-
-int s3c2410_dma_request(unsigned int channel,
-			struct s3c2410_dma_client *client,
-			void *dev)
-{
-	struct s3c2410_dma_chan *chan;
-	unsigned long flags;
-	int err;
-
-	pr_debug("dma%d: s3c2410_request_dma: client=%s, dev=%p\n",
-		 channel, client->name, dev);
-
-	local_irq_save(flags);
-
-	chan = s3c2410_dma_map_channel(channel);
-	if (chan == NULL) {
-		local_irq_restore(flags);
-		return -EBUSY;
-	}
-
-	dbg_showchan(chan);
-
-	chan->client = client;
-	chan->in_use = 1;
-
-	if (!chan->irq_claimed) {
-		pr_debug("dma%d: %s : requesting irq %d\n",
-			 channel, __FUNCTION__, chan->irq);
-
-		chan->irq_claimed = 1;
-		local_irq_restore(flags);
-
-		err = request_irq(chan->irq, s3c2410_dma_irq, IRQF_DISABLED,
-				  client->name, (void *)chan);
-
-		local_irq_save(flags);
-
-		if (err) {
-			chan->in_use = 0;
-			chan->irq_claimed = 0;
-			local_irq_restore(flags);
-
-			printk(KERN_ERR "%s: cannot get IRQ %d for DMA %d\n",
-			       client->name, chan->irq, chan->number);
-			return err;
-		}
-
-		chan->irq_enabled = 1;
-	}
-
-	local_irq_restore(flags);
-
-	/* need to setup */
-
-	pr_debug("%s: channel initialised, %p\n", __FUNCTION__, chan);
-
-	return 0;
-}
-
-EXPORT_SYMBOL(s3c2410_dma_request);
+static struct s3c24xx_dma_selection __initdata s3c2410_dma_sel = {
+	.select		= s3c2410_dma_select,
+	.dcon_mask	= 7 << 24,
+	.map		= s3c2410_dma_mappings,
+	.map_size	= ARRAY_SIZE(s3c2410_dma_mappings),
+};
 
-/* s3c2410_dma_free
- *
- * release the given channel back to the system, will stop and flush
- * any outstanding transfers, and ensure the channel is ready for the
- * next claimant.
- *
- * Note, although a warning is currently printed if the freeing client
- * info is not the same as the registrant's client info, the free is still
- * allowed to go through.
-*/
+static struct s3c24xx_dma_order __initdata s3c2410_dma_order = {
+	.channels	= {
+		[DMACH_SDI]	= {
+			.list	= {
+				[0]	= 3 | DMA_CH_VALID,
+				[1]	= 2 | DMA_CH_VALID,
+				[2]	= 0 | DMA_CH_VALID,
+			},
+		},
+		[DMACH_I2S_IN]	= {
+			.list	= {
+				[0]	= 1 | DMA_CH_VALID,
+				[1]	= 2 | DMA_CH_VALID,
+			},
+		},
+	},
+};
 
-int s3c2410_dma_free(dmach_t channel, struct s3c2410_dma_client *client)
+static int s3c2410_dma_add(struct sys_device *sysdev)
 {
-	struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
-	unsigned long flags;
-
-	if (chan == NULL)
-		return -EINVAL;
-
-	local_irq_save(flags);
-
-	if (chan->client != client) {
-		printk(KERN_WARNING "dma%d: possible free from different client (channel %p, passed %p)\n",
-		       channel, chan->client, client);
-	}
-
-	/* sort out stopping and freeing the channel */
-
-	if (chan->state != S3C2410_DMA_IDLE) {
-		pr_debug("%s: need to stop dma channel %p\n",
-		       __FUNCTION__, chan);
-
-		/* possibly flush the channel */
-		s3c2410_dma_ctrl(channel, S3C2410_DMAOP_STOP);
-	}
-
-	chan->client = NULL;
-	chan->in_use = 0;
-
-	if (chan->irq_claimed)
-		free_irq(chan->irq, (void *)chan);
-
-	chan->irq_claimed = 0;
-
-	if (!(channel & DMACH_LOW_LEVEL))
-		dma_chan_map[channel] = NULL;
-
-	local_irq_restore(flags);
-
-	return 0;
+	s3c2410_dma_init();
+	s3c24xx_dma_order_set(&s3c2410_dma_order);
+	return s3c24xx_dma_init_map(&s3c2410_dma_sel);
 }
 
-EXPORT_SYMBOL(s3c2410_dma_free);
-
-static int s3c2410_dma_dostop(struct s3c2410_dma_chan *chan)
-{
-	unsigned long flags;
-	unsigned long tmp;
-
-	pr_debug("%s:\n", __FUNCTION__);
-
-	dbg_showchan(chan);
-
-	local_irq_save(flags);
-
-	s3c2410_dma_call_op(chan,  S3C2410_DMAOP_STOP);
-
-	tmp = dma_rdreg(chan, S3C2410_DMA_DMASKTRIG);
-	tmp |= S3C2410_DMASKTRIG_STOP;
-	//tmp &= ~S3C2410_DMASKTRIG_ON;
-	dma_wrreg(chan, S3C2410_DMA_DMASKTRIG, tmp);
-
-#if 0
-	/* should also clear interrupts, according to WinCE BSP */
-	tmp = dma_rdreg(chan, S3C2410_DMA_DCON);
-	tmp |= S3C2410_DCON_NORELOAD;
-	dma_wrreg(chan, S3C2410_DMA_DCON, tmp);
-#endif
-
-	/* should stop do this, or should we wait for flush? */
-	chan->state      = S3C2410_DMA_IDLE;
-	chan->load_state = S3C2410_DMALOAD_NONE;
-
-	local_irq_restore(flags);
-
-	return 0;
-}
+#if defined(CONFIG_CPU_S3C2410)
+static struct sysdev_driver s3c2410_dma_driver = {
+	.add	= s3c2410_dma_add,
+};
 
-void s3c2410_dma_waitforstop(struct s3c2410_dma_chan *chan)
+static int __init s3c2410_dma_drvinit(void)
 {
-	unsigned long tmp;
-	unsigned int timeout = 0x10000;
-
-	while (timeout-- > 0) {
-		tmp = dma_rdreg(chan, S3C2410_DMA_DMASKTRIG);
-
-		if (!(tmp & S3C2410_DMASKTRIG_ON))
-			return;
-	}
-
-	pr_debug("dma%d: failed to stop?\n", chan->number);
+	return sysdev_driver_register(&s3c2410_sysclass, &s3c2410_dma_driver);
 }
 
-
-/* s3c2410_dma_flush
- *
- * stop the channel, and remove all current and pending transfers
-*/
-
-static int s3c2410_dma_flush(struct s3c2410_dma_chan *chan)
-{
-	struct s3c2410_dma_buf *buf, *next;
-	unsigned long flags;
-
-	pr_debug("%s: chan %p (%d)\n", __FUNCTION__, chan, chan->number);
-
-	dbg_showchan(chan);
-
-	local_irq_save(flags);
-
-	if (chan->state != S3C2410_DMA_IDLE) {
-		pr_debug("%s: stopping channel...\n", __FUNCTION__ );
-		s3c2410_dma_ctrl(chan->number, S3C2410_DMAOP_STOP);
-	}
-
-	buf = chan->curr;
-	if (buf == NULL)
-		buf = chan->next;
-
-	chan->curr = chan->next = chan->end = NULL;
-
-	if (buf != NULL) {
-		for ( ; buf != NULL; buf = next) {
-			next = buf->next;
-
-			pr_debug("%s: free buffer %p, next %p\n",
-			       __FUNCTION__, buf, buf->next);
-
-			s3c2410_dma_buffdone(chan, buf, S3C2410_RES_ABORT);
-			s3c2410_dma_freebuf(buf);
-		}
-	}
-
-	dbg_showregs(chan);
-
-	s3c2410_dma_waitforstop(chan);
-
-#if 0
-	/* should also clear interrupts, according to WinCE BSP */
-	{
-		unsigned long tmp;
-
-		tmp = dma_rdreg(chan, S3C2410_DMA_DCON);
-		tmp |= S3C2410_DCON_NORELOAD;
-		dma_wrreg(chan, S3C2410_DMA_DCON, tmp);
-	}
+arch_initcall(s3c2410_dma_drvinit);
 #endif
 
-	dbg_showregs(chan);
-
-	local_irq_restore(flags);
-
-	return 0;
-}
-
-int
-s3c2410_dma_started(struct s3c2410_dma_chan *chan)
-{
-	unsigned long flags;
-
-	local_irq_save(flags);
-
-	dbg_showchan(chan);
-
-	/* if we've only loaded one buffer onto the channel, then chec
-	 * to see if we have another, and if so, try and load it so when
-	 * the first buffer is finished, the new one will be loaded onto
-	 * the channel */
-
-	if (chan->next != NULL) {
-		if (chan->load_state == S3C2410_DMALOAD_1LOADED) {
-
-			if (s3c2410_dma_waitforload(chan, __LINE__) == 0) {
-				pr_debug("%s: buff not yet loaded, no more todo\n",
-					 __FUNCTION__);
-			} else {
-				chan->load_state = S3C2410_DMALOAD_1RUNNING;
-				s3c2410_dma_loadbuffer(chan, chan->next);
-			}
-
-		} else if (chan->load_state == S3C2410_DMALOAD_1RUNNING) {
-			s3c2410_dma_loadbuffer(chan, chan->next);
-		}
-	}
-
-
-	local_irq_restore(flags);
-
-	return 0;
-
-}
-
-int
-s3c2410_dma_ctrl(dmach_t channel, enum s3c2410_chan_op op)
-{
-	struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
-
-	if (chan == NULL)
-		return -EINVAL;
-
-	switch (op) {
-	case S3C2410_DMAOP_START:
-		return s3c2410_dma_start(chan);
-
-	case S3C2410_DMAOP_STOP:
-		return s3c2410_dma_dostop(chan);
-
-	case S3C2410_DMAOP_PAUSE:
-	case S3C2410_DMAOP_RESUME:
-		return -ENOENT;
-
-	case S3C2410_DMAOP_FLUSH:
-		return s3c2410_dma_flush(chan);
-
-	case S3C2410_DMAOP_STARTED:
-		return s3c2410_dma_started(chan);
-
-	case S3C2410_DMAOP_TIMEOUT:
-		return 0;
-
-	}
-
-	return -ENOENT;      /* unknown, don't bother */
-}
-
-EXPORT_SYMBOL(s3c2410_dma_ctrl);
-
-/* DMA configuration for each channel
- *
- * DISRCC -> source of the DMA (AHB,APB)
- * DISRC  -> source address of the DMA
- * DIDSTC -> destination of the DMA (AHB,APD)
- * DIDST  -> destination address of the DMA
-*/
-
-/* s3c2410_dma_config
- *
- * xfersize:     size of unit in bytes (1,2,4)
- * dcon:         base value of the DCONx register
-*/
-
-int s3c2410_dma_config(dmach_t channel,
-		       int xferunit,
-		       int dcon)
-{
-	struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
-
-	pr_debug("%s: chan=%d, xfer_unit=%d, dcon=%08x\n",
-		 __FUNCTION__, channel, xferunit, dcon);
-
-	if (chan == NULL)
-		return -EINVAL;
-
-	pr_debug("%s: Initial dcon is %08x\n", __FUNCTION__, dcon);
-
-	dcon |= chan->dcon & dma_sel.dcon_mask;
-
-	pr_debug("%s: New dcon is %08x\n", __FUNCTION__, dcon);
-
-	switch (xferunit) {
-	case 1:
-		dcon |= S3C2410_DCON_BYTE;
-		break;
-
-	case 2:
-		dcon |= S3C2410_DCON_HALFWORD;
-		break;
-
-	case 4:
-		dcon |= S3C2410_DCON_WORD;
-		break;
-
-	default:
-		pr_debug("%s: bad transfer size %d\n", __FUNCTION__, xferunit);
-		return -EINVAL;
-	}
-
-	dcon |= S3C2410_DCON_HWTRIG;
-	dcon |= S3C2410_DCON_INTREQ;
-
-	pr_debug("%s: dcon now %08x\n", __FUNCTION__, dcon);
-
-	chan->dcon = dcon;
-	chan->xfer_unit = xferunit;
-
-	return 0;
-}
-
-EXPORT_SYMBOL(s3c2410_dma_config);
-
-int s3c2410_dma_setflags(dmach_t channel, unsigned int flags)
-{
-	struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
-
-	if (chan == NULL)
-		return -EINVAL;
-
-	pr_debug("%s: chan=%p, flags=%08x\n", __FUNCTION__, chan, flags);
-
-	chan->flags = flags;
-
-	return 0;
-}
-
-EXPORT_SYMBOL(s3c2410_dma_setflags);
-
-
-/* do we need to protect the settings of the fields from
- * irq?
-*/
-
-int s3c2410_dma_set_opfn(dmach_t channel, s3c2410_dma_opfn_t rtn)
-{
-	struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
-
-	if (chan == NULL)
-		return -EINVAL;
-
-	pr_debug("%s: chan=%p, op rtn=%p\n", __FUNCTION__, chan, rtn);
-
-	chan->op_fn = rtn;
-
-	return 0;
-}
-
-EXPORT_SYMBOL(s3c2410_dma_set_opfn);
-
-int s3c2410_dma_set_buffdone_fn(dmach_t channel, s3c2410_dma_cbfn_t rtn)
-{
-	struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
-
-	if (chan == NULL)
-		return -EINVAL;
-
-	pr_debug("%s: chan=%p, callback rtn=%p\n", __FUNCTION__, chan, rtn);
-
-	chan->callback_fn = rtn;
-
-	return 0;
-}
-
-EXPORT_SYMBOL(s3c2410_dma_set_buffdone_fn);
-
-/* s3c2410_dma_devconfig
- *
- * configure the dma source/destination hardware type and address
- *
- * source:    S3C2410_DMASRC_HW: source is hardware
- *            S3C2410_DMASRC_MEM: source is memory
- *
- * hwcfg:     the value for xxxSTCn register,
- *            bit 0: 0=increment pointer, 1=leave pointer
- *            bit 1: 0=soucre is AHB, 1=soucre is APB
- *
- * devaddr:   physical address of the source
-*/
-
-int s3c2410_dma_devconfig(int channel,
-			  enum s3c2410_dmasrc source,
-			  int hwcfg,
-			  unsigned long devaddr)
-{
-	struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
-
-	if (chan == NULL)
-		return -EINVAL;
-
-	pr_debug("%s: source=%d, hwcfg=%08x, devaddr=%08lx\n",
-		 __FUNCTION__, (int)source, hwcfg, devaddr);
-
-	chan->source = source;
-	chan->dev_addr = devaddr;
-
-	switch (source) {
-	case S3C2410_DMASRC_HW:
-		/* source is hardware */
-		pr_debug("%s: hw source, devaddr=%08lx, hwcfg=%d\n",
-			 __FUNCTION__, devaddr, hwcfg);
-		dma_wrreg(chan, S3C2410_DMA_DISRCC, hwcfg & 3);
-		dma_wrreg(chan, S3C2410_DMA_DISRC,  devaddr);
-		dma_wrreg(chan, S3C2410_DMA_DIDSTC, (0<<1) | (0<<0));
-
-		chan->addr_reg = dma_regaddr(chan, S3C2410_DMA_DIDST);
-		return 0;
-
-	case S3C2410_DMASRC_MEM:
-		/* source is memory */
-		pr_debug( "%s: mem source, devaddr=%08lx, hwcfg=%d\n",
-			  __FUNCTION__, devaddr, hwcfg);
-		dma_wrreg(chan, S3C2410_DMA_DISRCC, (0<<1) | (0<<0));
-		dma_wrreg(chan, S3C2410_DMA_DIDST,  devaddr);
-		dma_wrreg(chan, S3C2410_DMA_DIDSTC, hwcfg & 3);
-
-		chan->addr_reg = dma_regaddr(chan, S3C2410_DMA_DISRC);
-		return 0;
-	}
-
-	printk(KERN_ERR "dma%d: invalid source type (%d)\n", channel, source);
-	return -EINVAL;
-}
-
-EXPORT_SYMBOL(s3c2410_dma_devconfig);
-
-/* s3c2410_dma_getposition
- *
- * returns the current transfer points for the dma source and destination
-*/
-
-int s3c2410_dma_getposition(dmach_t channel, dma_addr_t *src, dma_addr_t *dst)
-{
- 	struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
-
-	if (chan == NULL)
-		return -EINVAL;
-
-	if (src != NULL)
- 		*src = dma_rdreg(chan, S3C2410_DMA_DCSRC);
-
- 	if (dst != NULL)
- 		*dst = dma_rdreg(chan, S3C2410_DMA_DCDST);
-
- 	return 0;
-}
-
-EXPORT_SYMBOL(s3c2410_dma_getposition);
-
-
-/* system device class */
-
-#ifdef CONFIG_PM
-
-static int s3c2410_dma_suspend(struct sys_device *dev, pm_message_t state)
-{
-	struct s3c2410_dma_chan *cp = container_of(dev, struct s3c2410_dma_chan, dev);
-
-	printk(KERN_DEBUG "suspending dma channel %d\n", cp->number);
-
-	if (dma_rdreg(cp, S3C2410_DMA_DMASKTRIG) & S3C2410_DMASKTRIG_ON) {
-		/* the dma channel is still working, which is probably
-		 * a bad thing to do over suspend/resume. We stop the
-		 * channel and assume that the client is either going to
-		 * retry after resume, or that it is broken.
-		 */
-
-		printk(KERN_INFO "dma: stopping channel %d due to suspend\n",
-		       cp->number);
-
-		s3c2410_dma_dostop(cp);
-	}
-
-	return 0;
-}
-
-static int s3c2410_dma_resume(struct sys_device *dev)
-{
-	return 0;
-}
-
-#else
-#define s3c2410_dma_suspend NULL
-#define s3c2410_dma_resume  NULL
-#endif /* CONFIG_PM */
-
-struct sysdev_class dma_sysclass = {
-	set_kset_name("s3c24xx-dma"),
-	.suspend	= s3c2410_dma_suspend,
-	.resume		= s3c2410_dma_resume,
+#if defined(CONFIG_CPU_S3C2442)
+/* S3C2442 DMA contains the same selection table as the S3C2410 */
+static struct sysdev_driver s3c2442_dma_driver = {
+	.add	= s3c2410_dma_add,
 };
 
-/* kmem cache implementation */
-
-static void s3c2410_dma_cache_ctor(void *p, struct kmem_cache *c, unsigned long f)
-{
-	memset(p, 0, sizeof(struct s3c2410_dma_buf));
-}
-
-/* initialisation code */
-
-static int __init s3c2410_init_dma(void)
-{
-	struct s3c2410_dma_chan *cp;
-	int channel;
-	int ret;
-
-	printk("S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics\n");
-
-	dma_base = ioremap(S3C24XX_PA_DMA, 0x200);
-	if (dma_base == NULL) {
-		printk(KERN_ERR "dma failed to remap register block\n");
-		return -ENOMEM;
-	}
-
-	printk("Registering sysclass\n");
-
-	ret = sysdev_class_register(&dma_sysclass);
-	if (ret != 0) {
-		printk(KERN_ERR "dma sysclass registration failed\n");
-		goto err;
-	}
-
-	dma_kmem = kmem_cache_create("dma_desc", sizeof(struct s3c2410_dma_buf), 0,
-				     SLAB_HWCACHE_ALIGN,
-				     s3c2410_dma_cache_ctor, NULL);
-
-	if (dma_kmem == NULL) {
-		printk(KERN_ERR "dma failed to make kmem cache\n");
-		ret = -ENOMEM;
-		goto err;
-	}
-
-	for (channel = 0; channel < S3C2410_DMA_CHANNELS; channel++) {
-		cp = &s3c2410_chans[channel];
-
-		memset(cp, 0, sizeof(struct s3c2410_dma_chan));
-
-		/* dma channel irqs are in order.. */
-		cp->number = channel;
-		cp->irq    = channel + IRQ_DMA0;
-		cp->regs   = dma_base + (channel*0x40);
-
-		/* point current stats somewhere */
-		cp->stats  = &cp->stats_store;
-		cp->stats_store.timeout_shortest = LONG_MAX;
-
-		/* basic channel configuration */
-
-		cp->load_timeout = 1<<18;
-
-		/* register system device */
-
-		cp->dev.cls = &dma_sysclass;
-		cp->dev.id  = channel;
-		ret = sysdev_register(&cp->dev);
-
-		printk("DMA channel %d at %p, irq %d\n",
-		       cp->number, cp->regs, cp->irq);
-	}
-
-	return 0;
-
- err:
-	kmem_cache_destroy(dma_kmem);
-	iounmap(dma_base);
-	dma_base = NULL;
-	return ret;
-}
-
-core_initcall(s3c2410_init_dma);
-
-static inline int is_channel_valid(unsigned int channel)
+static int __init s3c2442_dma_drvinit(void)
 {
-	return (channel & DMA_CH_VALID);
+	return sysdev_driver_register(&s3c2442_sysclass, &s3c2442_dma_driver);
 }
 
-/* s3c2410_dma_map_channel()
- *
- * turn the virtual channel number into a real, and un-used hardware
- * channel.
- *
- * currently this code uses first-free channel from the specified harware
- * map, not taking into account anything that the board setup code may
- * have to say about the likely peripheral set to be in use.
-*/
-
-struct s3c2410_dma_chan *s3c2410_dma_map_channel(int channel)
-{
-	struct s3c24xx_dma_map *ch_map;
-	struct s3c2410_dma_chan *dmach;
-	int ch;
-
-	if (dma_sel.map == NULL || channel > dma_sel.map_size)
-		return NULL;
-
-	ch_map = dma_sel.map + channel;
-
-	for (ch = 0; ch < S3C2410_DMA_CHANNELS; ch++) {
-		if (!is_channel_valid(ch_map->channels[ch]))
-			continue;
-
-		if (s3c2410_chans[ch].in_use == 0) {
-			printk("mapped channel %d to %d\n", channel, ch);
-			break;
-		}
-	}
-
-	if (ch >= S3C2410_DMA_CHANNELS)
-		return NULL;
-
-	/* update our channel mapping */
-
-	dmach = &s3c2410_chans[ch];
-	dma_chan_map[channel] = dmach;
-
-	/* select the channel */
-
-	(dma_sel.select)(dmach, ch_map);
-
-	return dmach;
-}
-
-static void s3c24xx_dma_show_ch(struct s3c24xx_dma_map *map, int ch)
-{
-	/* show the channel configuration */
-
-	printk("%2d: %20s, channels %c%c%c%c\n", ch, map->name,
-	       (is_channel_valid(map->channels[0]) ? '0' : '-'),
-	       (is_channel_valid(map->channels[1]) ? '1' : '-'),
-	       (is_channel_valid(map->channels[2]) ? '2' : '-'),
-	       (is_channel_valid(map->channels[3]) ? '3' : '-'));
-}
-
-static int s3c24xx_dma_check_entry(struct s3c24xx_dma_map *map, int ch)
-{
-	if (1)
-		s3c24xx_dma_show_ch(map, ch);
-
-	return 0;
-}
-
-int __init s3c24xx_dma_init_map(struct s3c24xx_dma_selection *sel)
-{
-	struct s3c24xx_dma_map *nmap;
-	size_t map_sz = sizeof(*nmap) * sel->map_size;
-	int ptr;
-
-	nmap = kmalloc(map_sz, GFP_KERNEL);
-	if (nmap == NULL)
-		return -ENOMEM;
-
-	memcpy(nmap, sel->map, map_sz);
-	memcpy(&dma_sel, sel, sizeof(*sel));
-
-	dma_sel.map = nmap;
-
-	for (ptr = 0; ptr < sel->map_size; ptr++)
-		s3c24xx_dma_check_entry(nmap+ptr, ptr);
+arch_initcall(s3c2442_dma_drvinit);
+#endif
 
-	return 0;
-}
diff --git a/arch/arm/mach-s3c2410/dma.h b/arch/arm/mach-s3c2410/dma.h
deleted file mode 100644
index 0ebfe0aab80..00000000000
--- a/arch/arm/mach-s3c2410/dma.h
+++ /dev/null
@@ -1,45 +0,0 @@
-/* arch/arm/mach-s3c2410/dma.h
- *
- * Copyright (C) 2006 Simtec Electronics
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * Samsung S3C24XX DMA support
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-extern struct sysdev_class dma_sysclass;
-extern struct s3c2410_dma_chan s3c2410_chans[S3C2410_DMA_CHANNELS];
-
-#define DMA_CH_VALID		(1<<31)
-
-struct s3c24xx_dma_addr {
-	unsigned long		from;
-	unsigned long		to;
-};
-
-/* struct s3c24xx_dma_map
- *
- * this holds the mapping information for the channel selected
- * to be connected to the specified device
-*/
-
-struct s3c24xx_dma_map {
-	const char		*name;
-	struct s3c24xx_dma_addr  hw_addr;
-
-	unsigned long		 channels[S3C2410_DMA_CHANNELS];
-};
-
-struct s3c24xx_dma_selection {
-	struct s3c24xx_dma_map	*map;
-	unsigned long		 map_size;
-	unsigned long		 dcon_mask;
-
-	void	(*select)(struct s3c2410_dma_chan *chan,
-			  struct s3c24xx_dma_map *map);
-};
-
-extern int s3c24xx_dma_init_map(struct s3c24xx_dma_selection *sel);
diff --git a/arch/arm/mach-s3c2410/gpio.c b/arch/arm/mach-s3c2410/gpio.c
index f6fb215bb48..01e795d1146 100644
--- a/arch/arm/mach-s3c2410/gpio.c
+++ b/arch/arm/mach-s3c2410/gpio.c
@@ -1,9 +1,9 @@
 /* linux/arch/arm/mach-s3c2410/gpio.c
  *
- * Copyright (c) 2004-2005 Simtec Electronics
+ * Copyright (c) 2004-2006 Simtec Electronics
  *	Ben Dooks <ben@simtec.co.uk>
  *
- * S3C24XX GPIO support
+ * S3C2410 GPIO support
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
@@ -18,8 +18,7 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
-*/
-
+ */
 
 #include <linux/kernel.h>
 #include <linux/init.h>
@@ -33,156 +32,40 @@
 
 #include <asm/arch/regs-gpio.h>
 
-void s3c2410_gpio_cfgpin(unsigned int pin, unsigned int function)
-{
-	void __iomem *base = S3C24XX_GPIO_BASE(pin);
-	unsigned long mask;
-	unsigned long con;
-	unsigned long flags;
-
-	if (pin < S3C2410_GPIO_BANKB) {
-		mask = 1 << S3C2410_GPIO_OFFSET(pin);
-	} else {
-		mask = 3 << S3C2410_GPIO_OFFSET(pin)*2;
-	}
-
-	switch (function) {
-	case S3C2410_GPIO_LEAVE:
-		mask = 0;
-		function = 0;
-		break;
-
-	case S3C2410_GPIO_INPUT:
-	case S3C2410_GPIO_OUTPUT:
-	case S3C2410_GPIO_SFN2:
-	case S3C2410_GPIO_SFN3:
-		if (pin < S3C2410_GPIO_BANKB) {
-			function -= 1;
-			function &= 1;
-			function <<= S3C2410_GPIO_OFFSET(pin);
-		} else {
-			function &= 3;
-			function <<= S3C2410_GPIO_OFFSET(pin)*2;
-		}
-	}
-
-	/* modify the specified register wwith IRQs off */
-
-	local_irq_save(flags);
-
-	con  = __raw_readl(base + 0x00);
-	con &= ~mask;
-	con |= function;
-
-	__raw_writel(con, base + 0x00);
-
-	local_irq_restore(flags);
-}
-
-EXPORT_SYMBOL(s3c2410_gpio_cfgpin);
-
-unsigned int s3c2410_gpio_getcfg(unsigned int pin)
-{
-	void __iomem *base = S3C24XX_GPIO_BASE(pin);
-	unsigned long val = __raw_readl(base);
-
-	if (pin < S3C2410_GPIO_BANKB) {
-		val >>= S3C2410_GPIO_OFFSET(pin);
-		val &= 1;
-		val += 1;
-	} else {
-		val >>= S3C2410_GPIO_OFFSET(pin)*2;
-		val &= 3;
-	}
-
-	return val | S3C2410_GPIO_INPUT;
-}
-
-EXPORT_SYMBOL(s3c2410_gpio_getcfg);
-
-void s3c2410_gpio_pullup(unsigned int pin, unsigned int to)
+int s3c2410_gpio_irqfilter(unsigned int pin, unsigned int on,
+			   unsigned int config)
 {
-	void __iomem *base = S3C24XX_GPIO_BASE(pin);
-	unsigned long offs = S3C2410_GPIO_OFFSET(pin);
+	void __iomem *reg = S3C24XX_EINFLT0;
 	unsigned long flags;
-	unsigned long up;
-
-	if (pin < S3C2410_GPIO_BANKB)
-		return;
-
-	local_irq_save(flags);
-
-	up = __raw_readl(base + 0x08);
-	up &= ~(1L << offs);
-	up |= to << offs;
-	__raw_writel(up, base + 0x08);
+	unsigned long val;
 
-	local_irq_restore(flags);
-}
+	if (pin < S3C2410_GPG8 || pin > S3C2410_GPG15)
+		return -1;
 
-EXPORT_SYMBOL(s3c2410_gpio_pullup);
+	config &= 0xff;
 
-void s3c2410_gpio_setpin(unsigned int pin, unsigned int to)
-{
-	void __iomem *base = S3C24XX_GPIO_BASE(pin);
-	unsigned long offs = S3C2410_GPIO_OFFSET(pin);
-	unsigned long flags;
-	unsigned long dat;
+	pin -= S3C2410_GPG8;
+	reg += pin & ~3;
 
 	local_irq_save(flags);
 
-	dat = __raw_readl(base + 0x04);
-	dat &= ~(1 << offs);
-	dat |= to << offs;
-	__raw_writel(dat, base + 0x04);
-
-	local_irq_restore(flags);
-}
-
-EXPORT_SYMBOL(s3c2410_gpio_setpin);
-
-unsigned int s3c2410_gpio_getpin(unsigned int pin)
-{
-	void __iomem *base = S3C24XX_GPIO_BASE(pin);
-	unsigned long offs = S3C2410_GPIO_OFFSET(pin);
+	/* update filter width and clock source */
 
-	return __raw_readl(base + 0x04) & (1<< offs);
-}
+	val = __raw_readl(reg);
+	val &= ~(0xff << ((pin & 3) * 8));
+	val |= config << ((pin & 3) * 8);
+	__raw_writel(val, reg);
 
-EXPORT_SYMBOL(s3c2410_gpio_getpin);
+	/* update filter enable */
 
-unsigned int s3c2410_modify_misccr(unsigned int clear, unsigned int change)
-{
-	unsigned long flags;
-	unsigned long misccr;
+	val = __raw_readl(S3C24XX_EXTINT2);
+	val &= ~(1 << ((pin * 4) + 3));
+	val |= on << ((pin * 4) + 3);
+	__raw_writel(val, S3C24XX_EXTINT2);
 
-	local_irq_save(flags);
-	misccr = __raw_readl(S3C24XX_MISCCR);
-	misccr &= ~clear;
-	misccr ^= change;
-	__raw_writel(misccr, S3C24XX_MISCCR);
 	local_irq_restore(flags);
 
-	return misccr;
-}
-
-EXPORT_SYMBOL(s3c2410_modify_misccr);
-
-int s3c2410_gpio_getirq(unsigned int pin)
-{
-	if (pin < S3C2410_GPF0 || pin > S3C2410_GPG15)
-		return -1;	/* not valid interrupts */
-
-	if (pin < S3C2410_GPG0 && pin > S3C2410_GPF7)
-		return -1;	/* not valid pin */
-
-	if (pin < S3C2410_GPF4)
-		return (pin - S3C2410_GPF0) + IRQ_EINT0;
-
-	if (pin < S3C2410_GPG0)
-		return (pin - S3C2410_GPF4) + IRQ_EINT4;
-
-	return (pin - S3C2410_GPG0) + IRQ_EINT8;
+	return 0;
 }
 
-EXPORT_SYMBOL(s3c2410_gpio_getirq);
+EXPORT_SYMBOL(s3c2410_gpio_irqfilter);
diff --git a/arch/arm/mach-s3c2410/irq.c b/arch/arm/mach-s3c2410/irq.c
index 3c0ed7871c5..53cbdaa43ac 100644
--- a/arch/arm/mach-s3c2410/irq.c
+++ b/arch/arm/mach-s3c2410/irq.c
@@ -1,6 +1,6 @@
 /* linux/arch/arm/mach-s3c2410/irq.c
  *
- * Copyright (c) 2003,2004 Simtec Electronics
+ * Copyright (c) 2006 Simtec Electronics
  *	Ben Dooks <ben@simtec.co.uk>
  *
  * This program is free software; you can redistribute it and/or modify
@@ -17,37 +17,6 @@
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
  *
- * Changelog:
- *
- *   22-Jul-2004  Ben Dooks <ben@simtec.co.uk>
- *                Fixed compile warnings
- *
- *   22-Jul-2004  Roc Wu <cooloney@yahoo.com.cn>
- *                Fixed s3c_extirq_type
- *
- *   21-Jul-2004  Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org>
- *                Addition of ADC/TC demux
- *
- *   04-Oct-2004  Klaus Fetscher <k.fetscher@fetron.de>
- *		  Fix for set_irq_type() on low EINT numbers
- *
- *   05-Oct-2004  Ben Dooks <ben@simtec.co.uk>
- *		  Tidy up KF's patch and sort out new release
- *
- *   05-Oct-2004  Ben Dooks <ben@simtec.co.uk>
- *		  Add support for power management controls
- *
- *   04-Nov-2004  Ben Dooks
- *		  Fix standard IRQ wake for EINT0..4 and RTC
- *
- *   22-Feb-2005  Ben Dooks
- *		  Fixed edge-triggering on ADC IRQ
- *
- *   28-Jun-2005  Ben Dooks
- *		  Mark IRQ_LCD valid
- *
- *   25-Jul-2005  Ben Dooks
- *		  Split the S3C2440 IRQ code to seperate file
 */
 
 #include <linux/init.h>
@@ -57,745 +26,23 @@
 #include <linux/ptrace.h>
 #include <linux/sysdev.h>
 
-#include <asm/hardware.h>
-#include <asm/irq.h>
-#include <asm/io.h>
-
-#include <asm/mach/irq.h>
-
-#include <asm/arch/regs-irq.h>
-#include <asm/arch/regs-gpio.h>
-
-#include "cpu.h"
-#include "pm.h"
-#include "irq.h"
-
-/* wakeup irq control */
-
-#ifdef CONFIG_PM
-
-/* state for IRQs over sleep */
-
-/* default is to allow for EINT0..EINT15, and IRQ_RTC as wakeup sources
- *
- * set bit to 1 in allow bitfield to enable the wakeup settings on it
-*/
-
-unsigned long s3c_irqwake_intallow	= 1L << (IRQ_RTC - IRQ_EINT0) | 0xfL;
-unsigned long s3c_irqwake_intmask	= 0xffffffffL;
-unsigned long s3c_irqwake_eintallow	= 0x0000fff0L;
-unsigned long s3c_irqwake_eintmask	= 0xffffffffL;
-
-int
-s3c_irq_wake(unsigned int irqno, unsigned int state)
-{
-	unsigned long irqbit = 1 << (irqno - IRQ_EINT0);
-
-	if (!(s3c_irqwake_intallow & irqbit))
-		return -ENOENT;
-
-	printk(KERN_INFO "wake %s for irq %d\n",
-	       state ? "enabled" : "disabled", irqno);
-
-	if (!state)
-		s3c_irqwake_intmask |= irqbit;
-	else
-		s3c_irqwake_intmask &= ~irqbit;
-
-	return 0;
-}
-
-static int
-s3c_irqext_wake(unsigned int irqno, unsigned int state)
-{
-	unsigned long bit = 1L << (irqno - EXTINT_OFF);
-
-	if (!(s3c_irqwake_eintallow & bit))
-		return -ENOENT;
-
-	printk(KERN_INFO "wake %s for irq %d\n",
-	       state ? "enabled" : "disabled", irqno);
-
-	if (!state)
-		s3c_irqwake_eintmask |= bit;
-	else
-		s3c_irqwake_eintmask &= ~bit;
-
-	return 0;
-}
-
-#else
-#define s3c_irqext_wake NULL
-#define s3c_irq_wake NULL
-#endif
-
-
-static void
-s3c_irq_mask(unsigned int irqno)
-{
-	unsigned long mask;
-
-	irqno -= IRQ_EINT0;
-
-	mask = __raw_readl(S3C2410_INTMSK);
-	mask |= 1UL << irqno;
-	__raw_writel(mask, S3C2410_INTMSK);
-}
-
-static inline void
-s3c_irq_ack(unsigned int irqno)
-{
-	unsigned long bitval = 1UL << (irqno - IRQ_EINT0);
-
-	__raw_writel(bitval, S3C2410_SRCPND);
-	__raw_writel(bitval, S3C2410_INTPND);
-}
-
-static inline void
-s3c_irq_maskack(unsigned int irqno)
-{
-	unsigned long bitval = 1UL << (irqno - IRQ_EINT0);
-	unsigned long mask;
-
-	mask = __raw_readl(S3C2410_INTMSK);
-	__raw_writel(mask|bitval, S3C2410_INTMSK);
-
-	__raw_writel(bitval, S3C2410_SRCPND);
-	__raw_writel(bitval, S3C2410_INTPND);
-}
-
-
-static void
-s3c_irq_unmask(unsigned int irqno)
-{
-	unsigned long mask;
-
-	if (irqno != IRQ_TIMER4 && irqno != IRQ_EINT8t23)
-		irqdbf2("s3c_irq_unmask %d\n", irqno);
-
-	irqno -= IRQ_EINT0;
-
-	mask = __raw_readl(S3C2410_INTMSK);
-	mask &= ~(1UL << irqno);
-	__raw_writel(mask, S3C2410_INTMSK);
-}
-
-struct irq_chip s3c_irq_level_chip = {
-	.name		= "s3c-level",
-	.ack		= s3c_irq_maskack,
-	.mask		= s3c_irq_mask,
-	.unmask		= s3c_irq_unmask,
-	.set_wake	= s3c_irq_wake
-};
-
-static struct irq_chip s3c_irq_chip = {
-	.name		= "s3c",
-	.ack		= s3c_irq_ack,
-	.mask		= s3c_irq_mask,
-	.unmask		= s3c_irq_unmask,
-	.set_wake	= s3c_irq_wake
-};
-
-static void
-s3c_irqext_mask(unsigned int irqno)
-{
-	unsigned long mask;
-
-	irqno -= EXTINT_OFF;
-
-	mask = __raw_readl(S3C24XX_EINTMASK);
-	mask |= ( 1UL << irqno);
-	__raw_writel(mask, S3C24XX_EINTMASK);
-}
-
-static void
-s3c_irqext_ack(unsigned int irqno)
-{
-	unsigned long req;
-	unsigned long bit;
-	unsigned long mask;
+#include <asm/plat-s3c24xx/cpu.h>
+#include <asm/plat-s3c24xx/pm.h>
 
-	bit = 1UL << (irqno - EXTINT_OFF);
-
-	mask = __raw_readl(S3C24XX_EINTMASK);
-
-	__raw_writel(bit, S3C24XX_EINTPEND);
-
-	req = __raw_readl(S3C24XX_EINTPEND);
-	req &= ~mask;
-
-	/* not sure if we should be acking the parent irq... */
-
-	if (irqno <= IRQ_EINT7 ) {
-		if ((req & 0xf0) == 0)
-			s3c_irq_ack(IRQ_EINT4t7);
-	} else {
-		if ((req >> 8) == 0)
-			s3c_irq_ack(IRQ_EINT8t23);
-	}
-}
-
-static void
-s3c_irqext_unmask(unsigned int irqno)
+static int s3c2410_irq_add(struct sys_device *sysdev)
 {
-	unsigned long mask;
-
-	irqno -= EXTINT_OFF;
-
-	mask = __raw_readl(S3C24XX_EINTMASK);
-	mask &= ~( 1UL << irqno);
-	__raw_writel(mask, S3C24XX_EINTMASK);
-}
-
-int
-s3c_irqext_type(unsigned int irq, unsigned int type)
-{
-	void __iomem *extint_reg;
-	void __iomem *gpcon_reg;
-	unsigned long gpcon_offset, extint_offset;
-	unsigned long newvalue = 0, value;
-
-	if ((irq >= IRQ_EINT0) && (irq <= IRQ_EINT3))
-	{
-		gpcon_reg = S3C2410_GPFCON;
-		extint_reg = S3C24XX_EXTINT0;
-		gpcon_offset = (irq - IRQ_EINT0) * 2;
-		extint_offset = (irq - IRQ_EINT0) * 4;
-	}
-	else if ((irq >= IRQ_EINT4) && (irq <= IRQ_EINT7))
-	{
-		gpcon_reg = S3C2410_GPFCON;
-		extint_reg = S3C24XX_EXTINT0;
-		gpcon_offset = (irq - (EXTINT_OFF)) * 2;
-		extint_offset = (irq - (EXTINT_OFF)) * 4;
-	}
-	else if ((irq >= IRQ_EINT8) && (irq <= IRQ_EINT15))
-	{
-		gpcon_reg = S3C2410_GPGCON;
-		extint_reg = S3C24XX_EXTINT1;
-		gpcon_offset = (irq - IRQ_EINT8) * 2;
-		extint_offset = (irq - IRQ_EINT8) * 4;
-	}
-	else if ((irq >= IRQ_EINT16) && (irq <= IRQ_EINT23))
-	{
-		gpcon_reg = S3C2410_GPGCON;
-		extint_reg = S3C24XX_EXTINT2;
-		gpcon_offset = (irq - IRQ_EINT8) * 2;
-		extint_offset = (irq - IRQ_EINT16) * 4;
-	} else
-		return -1;
-
-	/* Set the GPIO to external interrupt mode */
-	value = __raw_readl(gpcon_reg);
-	value = (value & ~(3 << gpcon_offset)) | (0x02 << gpcon_offset);
-	__raw_writel(value, gpcon_reg);
-
-	/* Set the external interrupt to pointed trigger type */
-	switch (type)
-	{
-		case IRQT_NOEDGE:
-			printk(KERN_WARNING "No edge setting!\n");
-			break;
-
-		case IRQT_RISING:
-			newvalue = S3C2410_EXTINT_RISEEDGE;
-			break;
-
-		case IRQT_FALLING:
-			newvalue = S3C2410_EXTINT_FALLEDGE;
-			break;
-
-		case IRQT_BOTHEDGE:
-			newvalue = S3C2410_EXTINT_BOTHEDGE;
-			break;
-
-		case IRQT_LOW:
-			newvalue = S3C2410_EXTINT_LOWLEV;
-			break;
-
-		case IRQT_HIGH:
-			newvalue = S3C2410_EXTINT_HILEV;
-			break;
-
-		default:
-			printk(KERN_ERR "No such irq type %d", type);
-			return -1;
-	}
-
-	value = __raw_readl(extint_reg);
-	value = (value & ~(7 << extint_offset)) | (newvalue << extint_offset);
-	__raw_writel(value, extint_reg);
-
 	return 0;
 }
 
-static struct irq_chip s3c_irqext_chip = {
-	.name		= "s3c-ext",
-	.mask		= s3c_irqext_mask,
-	.unmask		= s3c_irqext_unmask,
-	.ack		= s3c_irqext_ack,
-	.set_type	= s3c_irqext_type,
-	.set_wake	= s3c_irqext_wake
-};
-
-static struct irq_chip s3c_irq_eint0t4 = {
-	.name		= "s3c-ext0",
-	.ack		= s3c_irq_ack,
-	.mask		= s3c_irq_mask,
-	.unmask		= s3c_irq_unmask,
-	.set_wake	= s3c_irq_wake,
-	.set_type	= s3c_irqext_type,
-};
-
-/* mask values for the parent registers for each of the interrupt types */
-
-#define INTMSK_UART0	 (1UL << (IRQ_UART0 - IRQ_EINT0))
-#define INTMSK_UART1	 (1UL << (IRQ_UART1 - IRQ_EINT0))
-#define INTMSK_UART2	 (1UL << (IRQ_UART2 - IRQ_EINT0))
-#define INTMSK_ADCPARENT (1UL << (IRQ_ADCPARENT - IRQ_EINT0))
-
-
-/* UART0 */
-
-static void
-s3c_irq_uart0_mask(unsigned int irqno)
-{
-	s3c_irqsub_mask(irqno, INTMSK_UART0, 7);
-}
-
-static void
-s3c_irq_uart0_unmask(unsigned int irqno)
-{
-	s3c_irqsub_unmask(irqno, INTMSK_UART0);
-}
-
-static void
-s3c_irq_uart0_ack(unsigned int irqno)
-{
-	s3c_irqsub_maskack(irqno, INTMSK_UART0, 7);
-}
-
-static struct irq_chip s3c_irq_uart0 = {
-	.name		= "s3c-uart0",
-	.mask		= s3c_irq_uart0_mask,
-	.unmask		= s3c_irq_uart0_unmask,
-	.ack		= s3c_irq_uart0_ack,
-};
-
-/* UART1 */
-
-static void
-s3c_irq_uart1_mask(unsigned int irqno)
-{
-	s3c_irqsub_mask(irqno, INTMSK_UART1, 7 << 3);
-}
-
-static void
-s3c_irq_uart1_unmask(unsigned int irqno)
-{
-	s3c_irqsub_unmask(irqno, INTMSK_UART1);
-}
-
-static void
-s3c_irq_uart1_ack(unsigned int irqno)
-{
-	s3c_irqsub_maskack(irqno, INTMSK_UART1, 7 << 3);
-}
-
-static struct irq_chip s3c_irq_uart1 = {
-	.name		= "s3c-uart1",
-	.mask		= s3c_irq_uart1_mask,
-	.unmask		= s3c_irq_uart1_unmask,
-	.ack		= s3c_irq_uart1_ack,
-};
-
-/* UART2 */
-
-static void
-s3c_irq_uart2_mask(unsigned int irqno)
-{
-	s3c_irqsub_mask(irqno, INTMSK_UART2, 7 << 6);
-}
-
-static void
-s3c_irq_uart2_unmask(unsigned int irqno)
-{
-	s3c_irqsub_unmask(irqno, INTMSK_UART2);
-}
-
-static void
-s3c_irq_uart2_ack(unsigned int irqno)
-{
-	s3c_irqsub_maskack(irqno, INTMSK_UART2, 7 << 6);
-}
-
-static struct irq_chip s3c_irq_uart2 = {
-	.name		= "s3c-uart2",
-	.mask		= s3c_irq_uart2_mask,
-	.unmask		= s3c_irq_uart2_unmask,
-	.ack		= s3c_irq_uart2_ack,
-};
-
-/* ADC and Touchscreen */
-
-static void
-s3c_irq_adc_mask(unsigned int irqno)
-{
-	s3c_irqsub_mask(irqno, INTMSK_ADCPARENT, 3 << 9);
-}
-
-static void
-s3c_irq_adc_unmask(unsigned int irqno)
-{
-	s3c_irqsub_unmask(irqno, INTMSK_ADCPARENT);
-}
-
-static void
-s3c_irq_adc_ack(unsigned int irqno)
-{
-	s3c_irqsub_ack(irqno, INTMSK_ADCPARENT, 3 << 9);
-}
-
-static struct irq_chip s3c_irq_adc = {
-	.name		= "s3c-adc",
-	.mask		= s3c_irq_adc_mask,
-	.unmask		= s3c_irq_adc_unmask,
-	.ack		= s3c_irq_adc_ack,
-};
-
-/* irq demux for adc */
-static void s3c_irq_demux_adc(unsigned int irq,
-			      struct irq_desc *desc)
-{
-	unsigned int subsrc, submsk;
-	unsigned int offset = 9;
-	struct irq_desc *mydesc;
-
-	/* read the current pending interrupts, and the mask
-	 * for what it is available */
-
-	subsrc = __raw_readl(S3C2410_SUBSRCPND);
-	submsk = __raw_readl(S3C2410_INTSUBMSK);
-
-	subsrc &= ~submsk;
-	subsrc >>= offset;
-	subsrc &= 3;
-
-	if (subsrc != 0) {
-		if (subsrc & 1) {
-			mydesc = irq_desc + IRQ_TC;
-			desc_handle_irq(IRQ_TC, mydesc);
-		}
-		if (subsrc & 2) {
-			mydesc = irq_desc + IRQ_ADC;
-			desc_handle_irq(IRQ_ADC, mydesc);
-		}
-	}
-}
-
-static void s3c_irq_demux_uart(unsigned int start)
-{
-	unsigned int subsrc, submsk;
-	unsigned int offset = start - IRQ_S3CUART_RX0;
-	struct irq_desc *desc;
-
-	/* read the current pending interrupts, and the mask
-	 * for what it is available */
-
-	subsrc = __raw_readl(S3C2410_SUBSRCPND);
-	submsk = __raw_readl(S3C2410_INTSUBMSK);
-
-	irqdbf2("s3c_irq_demux_uart: start=%d (%d), subsrc=0x%08x,0x%08x\n",
-		start, offset, subsrc, submsk);
-
-	subsrc &= ~submsk;
-	subsrc >>= offset;
-	subsrc &= 7;
-
-	if (subsrc != 0) {
-		desc = irq_desc + start;
-
-		if (subsrc & 1)
-			desc_handle_irq(start, desc);
-
-		desc++;
-
-		if (subsrc & 2)
-			desc_handle_irq(start+1, desc);
-
-		desc++;
-
-		if (subsrc & 4)
-			desc_handle_irq(start+2, desc);
-	}
-}
-
-/* uart demux entry points */
-
-static void
-s3c_irq_demux_uart0(unsigned int irq,
-		    struct irq_desc *desc)
-{
-	irq = irq;
-	s3c_irq_demux_uart(IRQ_S3CUART_RX0);
-}
-
-static void
-s3c_irq_demux_uart1(unsigned int irq,
-		    struct irq_desc *desc)
-{
-	irq = irq;
-	s3c_irq_demux_uart(IRQ_S3CUART_RX1);
-}
-
-static void
-s3c_irq_demux_uart2(unsigned int irq,
-		    struct irq_desc *desc)
-{
-	irq = irq;
-	s3c_irq_demux_uart(IRQ_S3CUART_RX2);
-}
-
-static void
-s3c_irq_demux_extint8(unsigned int irq,
-		      struct irq_desc *desc)
-{
-	unsigned long eintpnd = __raw_readl(S3C24XX_EINTPEND);
-	unsigned long eintmsk = __raw_readl(S3C24XX_EINTMASK);
-
-	eintpnd &= ~eintmsk;
-	eintpnd &= ~0xff;	/* ignore lower irqs */
-
-	/* we may as well handle all the pending IRQs here */
-
-	while (eintpnd) {
-		irq = __ffs(eintpnd);
-		eintpnd &= ~(1<<irq);
-
-		irq += (IRQ_EINT4 - 4);
-		desc_handle_irq(irq, irq_desc + irq);
-	}
-
-}
-
-static void
-s3c_irq_demux_extint4t7(unsigned int irq,
-			struct irq_desc *desc)
-{
-	unsigned long eintpnd = __raw_readl(S3C24XX_EINTPEND);
-	unsigned long eintmsk = __raw_readl(S3C24XX_EINTMASK);
-
-	eintpnd &= ~eintmsk;
-	eintpnd &= 0xff;	/* only lower irqs */
-
-	/* we may as well handle all the pending IRQs here */
-
-	while (eintpnd) {
-		irq = __ffs(eintpnd);
-		eintpnd &= ~(1<<irq);
-
-		irq += (IRQ_EINT4 - 4);
-
-		desc_handle_irq(irq, irq_desc + irq);
-	}
-}
-
-#ifdef CONFIG_PM
-
-static struct sleep_save irq_save[] = {
-	SAVE_ITEM(S3C2410_INTMSK),
-	SAVE_ITEM(S3C2410_INTSUBMSK),
+static struct sysdev_driver s3c2410_irq_driver = {
+	.add		= s3c2410_irq_add,
+	.suspend	= s3c24xx_irq_suspend,
+	.resume		= s3c24xx_irq_resume,
 };
 
-/* the extint values move between the s3c2410/s3c2440 and the s3c2412
- * so we use an array to hold them, and to calculate the address of
- * the register at run-time
-*/
-
-static unsigned long save_extint[3];
-static unsigned long save_eintflt[4];
-static unsigned long save_eintmask;
-
-int s3c24xx_irq_suspend(struct sys_device *dev, pm_message_t state)
+static int s3c2410_irq_init(void)
 {
-	unsigned int i;
-
-	for (i = 0; i < ARRAY_SIZE(save_extint); i++)
-		save_extint[i] = __raw_readl(S3C24XX_EXTINT0 + (i*4));
-
-	for (i = 0; i < ARRAY_SIZE(save_eintflt); i++)
-		save_eintflt[i] = __raw_readl(S3C24XX_EINFLT0 + (i*4));
-
-	s3c2410_pm_do_save(irq_save, ARRAY_SIZE(irq_save));
-	save_eintmask = __raw_readl(S3C24XX_EINTMASK);
-
-	return 0;
+	return sysdev_driver_register(&s3c2410_sysclass, &s3c2410_irq_driver);
 }
 
-int s3c24xx_irq_resume(struct sys_device *dev)
-{
-	unsigned int i;
-
-	for (i = 0; i < ARRAY_SIZE(save_extint); i++)
-		__raw_writel(save_extint[i], S3C24XX_EXTINT0 + (i*4));
-
-	for (i = 0; i < ARRAY_SIZE(save_eintflt); i++)
-		__raw_writel(save_eintflt[i], S3C24XX_EINFLT0 + (i*4));
-
-	s3c2410_pm_do_restore(irq_save, ARRAY_SIZE(irq_save));
-	__raw_writel(save_eintmask, S3C24XX_EINTMASK);
-
-	return 0;
-}
-
-#else
-#define s3c24xx_irq_suspend NULL
-#define s3c24xx_irq_resume  NULL
-#endif
-
-/* s3c24xx_init_irq
- *
- * Initialise S3C2410 IRQ system
-*/
-
-void __init s3c24xx_init_irq(void)
-{
-	unsigned long pend;
-	unsigned long last;
-	int irqno;
-	int i;
-
-	irqdbf("s3c2410_init_irq: clearing interrupt status flags\n");
-
-	/* first, clear all interrupts pending... */
-
-	last = 0;
-	for (i = 0; i < 4; i++) {
-		pend = __raw_readl(S3C24XX_EINTPEND);
-
-		if (pend == 0 || pend == last)
-			break;
-
-		__raw_writel(pend, S3C24XX_EINTPEND);
-		printk("irq: clearing pending ext status %08x\n", (int)pend);
-		last = pend;
-	}
-
-	last = 0;
-	for (i = 0; i < 4; i++) {
-		pend = __raw_readl(S3C2410_INTPND);
-
-		if (pend == 0 || pend == last)
-			break;
-
-		__raw_writel(pend, S3C2410_SRCPND);
-		__raw_writel(pend, S3C2410_INTPND);
-		printk("irq: clearing pending status %08x\n", (int)pend);
-		last = pend;
-	}
-
-	last = 0;
-	for (i = 0; i < 4; i++) {
-		pend = __raw_readl(S3C2410_SUBSRCPND);
-
-		if (pend == 0 || pend == last)
-			break;
-
-		printk("irq: clearing subpending status %08x\n", (int)pend);
-		__raw_writel(pend, S3C2410_SUBSRCPND);
-		last = pend;
-	}
-
-	/* register the main interrupts */
-
-	irqdbf("s3c2410_init_irq: registering s3c2410 interrupt handlers\n");
-
-	for (irqno = IRQ_EINT4t7; irqno <= IRQ_ADCPARENT; irqno++) {
-		/* set all the s3c2410 internal irqs */
-
-		switch (irqno) {
-			/* deal with the special IRQs (cascaded) */
-
-		case IRQ_EINT4t7:
-		case IRQ_EINT8t23:
-		case IRQ_UART0:
-		case IRQ_UART1:
-		case IRQ_UART2:
-		case IRQ_ADCPARENT:
-			set_irq_chip(irqno, &s3c_irq_level_chip);
-			set_irq_handler(irqno, handle_level_irq);
-			break;
-
-		case IRQ_RESERVED6:
-		case IRQ_RESERVED24:
-			/* no IRQ here */
-			break;
-
-		default:
-			//irqdbf("registering irq %d (s3c irq)\n", irqno);
-			set_irq_chip(irqno, &s3c_irq_chip);
-			set_irq_handler(irqno, handle_edge_irq);
-			set_irq_flags(irqno, IRQF_VALID);
-		}
-	}
-
-	/* setup the cascade irq handlers */
-
-	set_irq_chained_handler(IRQ_EINT4t7, s3c_irq_demux_extint4t7);
-	set_irq_chained_handler(IRQ_EINT8t23, s3c_irq_demux_extint8);
-
-	set_irq_chained_handler(IRQ_UART0, s3c_irq_demux_uart0);
-	set_irq_chained_handler(IRQ_UART1, s3c_irq_demux_uart1);
-	set_irq_chained_handler(IRQ_UART2, s3c_irq_demux_uart2);
-	set_irq_chained_handler(IRQ_ADCPARENT, s3c_irq_demux_adc);
-
-	/* external interrupts */
-
-	for (irqno = IRQ_EINT0; irqno <= IRQ_EINT3; irqno++) {
-		irqdbf("registering irq %d (ext int)\n", irqno);
-		set_irq_chip(irqno, &s3c_irq_eint0t4);
-		set_irq_handler(irqno, handle_edge_irq);
-		set_irq_flags(irqno, IRQF_VALID);
-	}
-
-	for (irqno = IRQ_EINT4; irqno <= IRQ_EINT23; irqno++) {
-		irqdbf("registering irq %d (extended s3c irq)\n", irqno);
-		set_irq_chip(irqno, &s3c_irqext_chip);
-		set_irq_handler(irqno, handle_edge_irq);
-		set_irq_flags(irqno, IRQF_VALID);
-	}
-
-	/* register the uart interrupts */
-
-	irqdbf("s3c2410: registering external interrupts\n");
-
-	for (irqno = IRQ_S3CUART_RX0; irqno <= IRQ_S3CUART_ERR0; irqno++) {
-		irqdbf("registering irq %d (s3c uart0 irq)\n", irqno);
-		set_irq_chip(irqno, &s3c_irq_uart0);
-		set_irq_handler(irqno, handle_level_irq);
-		set_irq_flags(irqno, IRQF_VALID);
-	}
-
-	for (irqno = IRQ_S3CUART_RX1; irqno <= IRQ_S3CUART_ERR1; irqno++) {
-		irqdbf("registering irq %d (s3c uart1 irq)\n", irqno);
-		set_irq_chip(irqno, &s3c_irq_uart1);
-		set_irq_handler(irqno, handle_level_irq);
-		set_irq_flags(irqno, IRQF_VALID);
-	}
-
-	for (irqno = IRQ_S3CUART_RX2; irqno <= IRQ_S3CUART_ERR2; irqno++) {
-		irqdbf("registering irq %d (s3c uart2 irq)\n", irqno);
-		set_irq_chip(irqno, &s3c_irq_uart2);
-		set_irq_handler(irqno, handle_level_irq);
-		set_irq_flags(irqno, IRQF_VALID);
-	}
-
-	for (irqno = IRQ_TC; irqno <= IRQ_ADC; irqno++) {
-		irqdbf("registering irq %d (s3c adc irq)\n", irqno);
-		set_irq_chip(irqno, &s3c_irq_adc);
-		set_irq_handler(irqno, handle_edge_irq);
-		set_irq_flags(irqno, IRQF_VALID);
-	}
-
-	irqdbf("s3c2410: registered interrupt handlers\n");
-}
+arch_initcall(s3c2410_irq_init);
diff --git a/arch/arm/mach-s3c2410/irq.h b/arch/arm/mach-s3c2410/irq.h
deleted file mode 100644
index e5913da3b91..00000000000
--- a/arch/arm/mach-s3c2410/irq.h
+++ /dev/null
@@ -1,107 +0,0 @@
-/* arch/arm/mach-s3c2410/irq.h
- *
- * Copyright (c) 2004-2005 Simtec Electronics
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * Header file for S3C24XX CPU IRQ support
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#define irqdbf(x...)
-#define irqdbf2(x...)
-
-#define EXTINT_OFF (IRQ_EINT4 - 4)
-
-extern struct irq_chip s3c_irq_level_chip;
-
-static inline void
-s3c_irqsub_mask(unsigned int irqno, unsigned int parentbit,
-		int subcheck)
-{
-	unsigned long mask;
-	unsigned long submask;
-
-	submask = __raw_readl(S3C2410_INTSUBMSK);
-	mask = __raw_readl(S3C2410_INTMSK);
-
-	submask |= (1UL << (irqno - IRQ_S3CUART_RX0));
-
-	/* check to see if we need to mask the parent IRQ */
-
-	if ((submask  & subcheck) == subcheck) {
-		__raw_writel(mask | parentbit, S3C2410_INTMSK);
-	}
-
-	/* write back masks */
-	__raw_writel(submask, S3C2410_INTSUBMSK);
-
-}
-
-static inline void
-s3c_irqsub_unmask(unsigned int irqno, unsigned int parentbit)
-{
-	unsigned long mask;
-	unsigned long submask;
-
-	submask = __raw_readl(S3C2410_INTSUBMSK);
-	mask = __raw_readl(S3C2410_INTMSK);
-
-	submask &= ~(1UL << (irqno - IRQ_S3CUART_RX0));
-	mask &= ~parentbit;
-
-	/* write back masks */
-	__raw_writel(submask, S3C2410_INTSUBMSK);
-	__raw_writel(mask, S3C2410_INTMSK);
-}
-
-
-static inline void
-s3c_irqsub_maskack(unsigned int irqno, unsigned int parentmask, unsigned int group)
-{
-	unsigned int bit = 1UL << (irqno - IRQ_S3CUART_RX0);
-
-	s3c_irqsub_mask(irqno, parentmask, group);
-
-	__raw_writel(bit, S3C2410_SUBSRCPND);
-
-	/* only ack parent if we've got all the irqs (seems we must
-	 * ack, all and hope that the irq system retriggers ok when
-	 * the interrupt goes off again)
-	 */
-
-	if (1) {
-		__raw_writel(parentmask, S3C2410_SRCPND);
-		__raw_writel(parentmask, S3C2410_INTPND);
-	}
-}
-
-static inline void
-s3c_irqsub_ack(unsigned int irqno, unsigned int parentmask, unsigned int group)
-{
-	unsigned int bit = 1UL << (irqno - IRQ_S3CUART_RX0);
-
-	__raw_writel(bit, S3C2410_SUBSRCPND);
-
-	/* only ack parent if we've got all the irqs (seems we must
-	 * ack, all and hope that the irq system retriggers ok when
-	 * the interrupt goes off again)
-	 */
-
-	if (1) {
-		__raw_writel(parentmask, S3C2410_SRCPND);
-		__raw_writel(parentmask, S3C2410_INTPND);
-	}
-}
-
-/* exported for use in arch/arm/mach-s3c2410 */
-
-#ifdef CONFIG_PM
-extern int s3c_irq_wake(unsigned int irqno, unsigned int state);
-#else
-#define s3c_irq_wake NULL
-#endif
-
-extern int s3c_irqext_type(unsigned int irq, unsigned int type);
diff --git a/arch/arm/mach-s3c2410/mach-amlm5900.c b/arch/arm/mach-s3c2410/mach-amlm5900.c
index 817e2c68441..72f2cc4fcd0 100644
--- a/arch/arm/mach-s3c2410/mach-amlm5900.c
+++ b/arch/arm/mach-s3c2410/mach-amlm5900.c
@@ -1,4 +1,4 @@
-/***********************************************************************
+/* linux/arch/arm/mach-s3c2410/mach-amlm5900.c
  *
  * linux/arch/arm/mach-s3c2410/mach-amlm5900.c
  *
@@ -35,7 +35,7 @@
 #include <linux/device.h>
 #include <linux/platform_device.h>
 #include <linux/proc_fs.h>
-
+#include <linux/serial_core.h>
 
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
@@ -52,8 +52,8 @@
 #include <asm/arch/regs-lcd.h>
 #include <asm/arch/regs-gpio.h>
 
-#include "devs.h"
-#include "cpu.h"
+#include <asm/plat-s3c24xx/devs.h>
+#include <asm/plat-s3c24xx/cpu.h>
 
 #ifdef CONFIG_MTD_PARTITIONS
 
@@ -113,12 +113,6 @@ static struct platform_device amlm5900_device_nor = {
 #endif
 
 static struct map_desc amlm5900_iodesc[] __initdata = {
-	{
-		.virtual	= (u32)S3C24XX_VA_SPI,
-		.pfn		= __phys_to_pfn(S3C2410_PA_SPI),
-		.length		= SZ_1M,
-		.type		= MT_DEVICE
-	}
 };
 
 #define UCON S3C2410_UCON_DEFAULT
diff --git a/arch/arm/mach-s3c2410/mach-bast.c b/arch/arm/mach-s3c2410/mach-bast.c
index b8b76757ec5..7b81296427e 100644
--- a/arch/arm/mach-s3c2410/mach-bast.c
+++ b/arch/arm/mach-s3c2410/mach-bast.c
@@ -50,9 +50,9 @@
 
 #include <linux/serial_8250.h>
 
-#include "clock.h"
-#include "devs.h"
-#include "cpu.h"
+#include <asm/plat-s3c24xx/clock.h>
+#include <asm/plat-s3c24xx/devs.h>
+#include <asm/plat-s3c24xx/cpu.h>
 #include "usb-simtec.h"
 
 #define COPYRIGHT ", (c) 2004-2005 Simtec Electronics"
diff --git a/arch/arm/mach-s3c2410/mach-h1940.c b/arch/arm/mach-s3c2410/mach-h1940.c
index 15b625eae49..01c60d0923c 100644
--- a/arch/arm/mach-s3c2410/mach-h1940.c
+++ b/arch/arm/mach-s3c2410/mach-h1940.c
@@ -25,23 +25,24 @@
 #include <asm/mach/irq.h>
 
 #include <asm/hardware.h>
-#include <asm/hardware/iomd.h>
 #include <asm/io.h>
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-
 #include <asm/arch/regs-serial.h>
 #include <asm/arch/regs-lcd.h>
+#include <asm/arch/regs-gpio.h>
+#include <asm/arch/regs-clock.h>
 
 #include <asm/arch/h1940.h>
 #include <asm/arch/h1940-latch.h>
 #include <asm/arch/fb.h>
+#include <asm/arch/udc.h>
 
-#include "clock.h"
-#include "devs.h"
-#include "cpu.h"
-#include "pm.h"
+#include <asm/plat-s3c24xx/clock.h>
+#include <asm/plat-s3c24xx/devs.h>
+#include <asm/plat-s3c24xx/cpu.h>
+#include <asm/plat-s3c24xx/pm.h>
 
 static struct map_desc h1940_iodesc[] __initdata = {
 	[0] = {
@@ -102,6 +103,32 @@ void h1940_latch_control(unsigned int clear, unsigned int set)
 
 EXPORT_SYMBOL_GPL(h1940_latch_control);
 
+static void h1940_udc_pullup(enum s3c2410_udc_cmd_e cmd)
+{
+	printk(KERN_DEBUG "udc: pullup(%d)\n",cmd);
+
+	switch (cmd)
+	{
+		case S3C2410_UDC_P_ENABLE :
+			h1940_latch_control(0, H1940_LATCH_USB_DP);
+			break;
+		case S3C2410_UDC_P_DISABLE :
+			h1940_latch_control(H1940_LATCH_USB_DP, 0);
+			break;
+		case S3C2410_UDC_P_RESET :
+			break;
+		default:
+			break;
+	}
+}
+
+static struct s3c2410_udc_mach_info h1940_udc_cfg __initdata = {
+	.udc_command		= h1940_udc_pullup,
+	.vbus_pin		= S3C2410_GPG5,
+	.vbus_pin_inverted	= 1,
+};
+
+
 
 /**
  * Set lcd on or off
@@ -146,12 +173,19 @@ static struct s3c2410fb_mach_info h1940_lcdcfg __initdata = {
 	.bpp=		{16,16,16},
 };
 
+static struct platform_device s3c_device_leds = {
+	.name             = "h1940-leds",
+	.id               = -1,
+};
+
 static struct platform_device *h1940_devices[] __initdata = {
 	&s3c_device_usb,
 	&s3c_device_lcd,
 	&s3c_device_wdt,
 	&s3c_device_i2c,
 	&s3c_device_iis,
+	&s3c_device_usbgadget,
+	&s3c_device_leds,
 };
 
 static struct s3c24xx_board h1940_board __initdata = {
@@ -179,7 +213,23 @@ static void __init h1940_init_irq(void)
 
 static void __init h1940_init(void)
 {
+	u32 tmp;
+
 	s3c24xx_fb_set_platdata(&h1940_lcdcfg);
+ 	s3c24xx_udc_set_platdata(&h1940_udc_cfg);
+
+	/* Turn off suspend on both USB ports, and switch the
+	 * selectable USB port to USB device mode. */
+
+	s3c2410_modify_misccr(S3C2410_MISCCR_USBHOST |
+			      S3C2410_MISCCR_USBSUSPND0 |
+			      S3C2410_MISCCR_USBSUSPND1, 0x0);
+
+	tmp = (
+		 0x78 << S3C2410_PLLCON_MDIVSHIFT)
+	      | (0x02 << S3C2410_PLLCON_PDIVSHIFT)
+	      | (0x03 << S3C2410_PLLCON_SDIVSHIFT);
+	writel(tmp, S3C2410_UPLLCON);
 }
 
 MACHINE_START(H1940, "IPAQ-H1940")
@@ -189,6 +239,6 @@ MACHINE_START(H1940, "IPAQ-H1940")
 	.boot_params	= S3C2410_SDRAM_PA + 0x100,
 	.map_io		= h1940_map_io,
 	.init_irq	= h1940_init_irq,
-	.init_machine   = h1940_init,
+	.init_machine	= h1940_init,
 	.timer		= &s3c24xx_timer,
 MACHINE_END
diff --git a/arch/arm/mach-s3c2410/mach-n30.c b/arch/arm/mach-s3c2410/mach-n30.c
index 0411e9adb54..261aa4cc077 100644
--- a/arch/arm/mach-s3c2410/mach-n30.c
+++ b/arch/arm/mach-s3c2410/mach-n30.c
@@ -29,7 +29,6 @@
 #include <asm/mach/irq.h>
 
 #include <asm/hardware.h>
-#include <asm/hardware/iomd.h>
 #include <asm/io.h>
 #include <asm/irq.h>
 #include <asm/mach-types.h>
@@ -38,10 +37,10 @@
 #include <asm/arch/regs-gpio.h>
 #include <asm/arch/iic.h>
 
-#include "s3c2410.h"
-#include "clock.h"
-#include "devs.h"
-#include "cpu.h"
+#include <asm/plat-s3c24xx/s3c2410.h>
+#include <asm/plat-s3c24xx/clock.h>
+#include <asm/plat-s3c24xx/devs.h>
+#include <asm/plat-s3c24xx/cpu.h>
 
 static struct map_desc n30_iodesc[] __initdata = {
 	/* nothing here yet */
diff --git a/arch/arm/mach-s3c2410/mach-otom.c b/arch/arm/mach-s3c2410/mach-otom.c
index 2c738b375e4..c78ab75b44f 100644
--- a/arch/arm/mach-s3c2410/mach-otom.c
+++ b/arch/arm/mach-s3c2410/mach-otom.c
@@ -32,10 +32,10 @@
 #include <asm/arch/regs-serial.h>
 #include <asm/arch/regs-gpio.h>
 
-#include "s3c2410.h"
-#include "clock.h"
-#include "devs.h"
-#include "cpu.h"
+#include <asm/plat-s3c24xx/s3c2410.h>
+#include <asm/plat-s3c24xx/clock.h>
+#include <asm/plat-s3c24xx/devs.h>
+#include <asm/plat-s3c24xx/cpu.h>
 
 static struct map_desc otom11_iodesc[] __initdata = {
   /* Device area */
diff --git a/arch/arm/mach-s3c2410/mach-qt2410.c b/arch/arm/mach-s3c2410/mach-qt2410.c
new file mode 100644
index 00000000000..c6a41593de2
--- /dev/null
+++ b/arch/arm/mach-s3c2410/mach-qt2410.c
@@ -0,0 +1,448 @@
+/* linux/arch/arm/mach-s3c2410/mach-qt2410.c
+ *
+ * Copyright (C) 2006 by OpenMoko, Inc.
+ * Author: Harald Welte <laforge@openmoko.org>
+ * All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/timer.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/serial_core.h>
+#include <linux/mmc/protocol.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/spi_bitbang.h>
+
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/nand_ecc.h>
+#include <linux/mtd/partitions.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <asm/hardware.h>
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/mach-types.h>
+
+#include <asm/arch/regs-gpio.h>
+#include <asm/arch/leds-gpio.h>
+#include <asm/arch/regs-serial.h>
+#include <asm/arch/fb.h>
+#include <asm/arch/nand.h>
+#include <asm/arch/udc.h>
+#include <asm/arch/spi.h>
+#include <asm/arch/spi-gpio.h>
+
+#include <asm/plat-s3c24xx/common-smdk.h>
+#include <asm/plat-s3c24xx/devs.h>
+#include <asm/plat-s3c24xx/cpu.h>
+#include <asm/plat-s3c24xx/pm.h>
+
+static struct map_desc qt2410_iodesc[] __initdata = {
+	{ 0xe0000000, __phys_to_pfn(S3C2410_CS3+0x01000000), SZ_1M, MT_DEVICE }
+};
+
+#define UCON S3C2410_UCON_DEFAULT
+#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB
+#define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE
+
+static struct s3c2410_uartcfg smdk2410_uartcfgs[] = {
+	[0] = {
+		.hwport	     = 0,
+		.flags	     = 0,
+		.ucon	     = UCON,
+		.ulcon	     = ULCON,
+		.ufcon	     = UFCON,
+	},
+	[1] = {
+		.hwport	     = 1,
+		.flags	     = 0,
+		.ucon	     = UCON,
+		.ulcon	     = ULCON,
+		.ufcon	     = UFCON,
+	},
+	[2] = {
+		.hwport	     = 2,
+		.flags	     = 0,
+		.ucon	     = UCON,
+		.ulcon	     = ULCON,
+		.ufcon	     = UFCON,
+	}
+};
+
+/* LCD driver info */
+
+/* Configuration for 640x480 SHARP LQ080V3DG01 */
+static struct s3c2410fb_mach_info qt2410_biglcd_cfg __initdata = {
+	.regs	= {
+
+		.lcdcon1	= S3C2410_LCDCON1_TFT16BPP |
+				  S3C2410_LCDCON1_TFT |
+				  S3C2410_LCDCON1_CLKVAL(0x01),	/* HCLK/4 */
+
+		.lcdcon2	= S3C2410_LCDCON2_VBPD(18) |	/* 19 */
+				  S3C2410_LCDCON2_LINEVAL(479) |
+				  S3C2410_LCDCON2_VFPD(10) |	/* 11 */
+				  S3C2410_LCDCON2_VSPW(14),	/* 15 */
+
+		.lcdcon3	= S3C2410_LCDCON3_HBPD(43) |	/* 44 */
+				  S3C2410_LCDCON3_HOZVAL(639) |	/* 640 */
+				  S3C2410_LCDCON3_HFPD(115),	/* 116 */
+
+		.lcdcon4	= S3C2410_LCDCON4_MVAL(0) |
+				  S3C2410_LCDCON4_HSPW(95),	/* 96 */
+
+		.lcdcon5	= S3C2410_LCDCON5_FRM565 |
+				  S3C2410_LCDCON5_INVVLINE |
+				  S3C2410_LCDCON5_INVVFRAME |
+				  S3C2410_LCDCON5_PWREN |
+				  S3C2410_LCDCON5_HWSWP,
+	},
+
+	.lpcsel		= ((0xCE6) & ~7) | 1<<4,
+
+	.width		= 640,
+	.height		= 480,
+
+	.xres		= {
+		.min	= 640,
+		.max	= 640,
+		.defval	= 640,
+	},
+
+	.yres		= {
+		.min	= 480,
+		.max	= 480,
+		.defval = 480,
+	},
+
+	.bpp		= {
+		.min	= 16,
+		.max	= 16,
+		.defval = 16,
+	},
+};
+
+/* Configuration for 480x640 toppoly TD028TTEC1 */
+static struct s3c2410fb_mach_info qt2410_prodlcd_cfg __initdata = {
+	.regs	= {
+
+		.lcdcon1	= S3C2410_LCDCON1_TFT16BPP |
+				  S3C2410_LCDCON1_TFT |
+				  S3C2410_LCDCON1_CLKVAL(0x01),	/* HCLK/4 */
+
+		.lcdcon2	= S3C2410_LCDCON2_VBPD(1) |	/* 2 */
+				  S3C2410_LCDCON2_LINEVAL(639) |/* 640 */
+				  S3C2410_LCDCON2_VFPD(3) |	/* 4 */
+				  S3C2410_LCDCON2_VSPW(1),	/* 2 */
+
+		.lcdcon3	= S3C2410_LCDCON3_HBPD(7) |	/* 8 */
+				  S3C2410_LCDCON3_HOZVAL(479) |	/* 479 */
+				  S3C2410_LCDCON3_HFPD(23),	/* 24 */
+
+		.lcdcon4	= S3C2410_LCDCON4_MVAL(0) |
+				  S3C2410_LCDCON4_HSPW(7),	/* 8 */
+
+		.lcdcon5	= S3C2410_LCDCON5_FRM565 |
+				  S3C2410_LCDCON5_INVVLINE |
+				  S3C2410_LCDCON5_INVVFRAME |
+				  S3C2410_LCDCON5_PWREN |
+				  S3C2410_LCDCON5_HWSWP,
+	},
+
+	.lpcsel		= ((0xCE6) & ~7) | 1<<4,
+
+	.width		= 480,
+	.height		= 640,
+
+	.xres		= {
+		.min	= 480,
+		.max	= 480,
+		.defval	= 480,
+	},
+
+	.yres		= {
+		.min	= 640,
+		.max	= 640,
+		.defval = 640,
+	},
+
+	.bpp		= {
+		.min	= 16,
+		.max	= 16,
+		.defval = 16,
+	},
+};
+
+/* Config for 240x320 LCD */
+static struct s3c2410fb_mach_info qt2410_lcd_cfg __initdata = {
+	.regs	= {
+
+		.lcdcon1	= S3C2410_LCDCON1_TFT16BPP |
+				  S3C2410_LCDCON1_TFT |
+				  S3C2410_LCDCON1_CLKVAL(0x04),
+
+		.lcdcon2	= S3C2410_LCDCON2_VBPD(1) |
+				  S3C2410_LCDCON2_LINEVAL(319) |
+				  S3C2410_LCDCON2_VFPD(6) |
+				  S3C2410_LCDCON2_VSPW(3),
+
+		.lcdcon3	= S3C2410_LCDCON3_HBPD(12) |
+				  S3C2410_LCDCON3_HOZVAL(239) |
+				  S3C2410_LCDCON3_HFPD(7),
+
+		.lcdcon4	= S3C2410_LCDCON4_MVAL(0) |
+				  S3C2410_LCDCON4_HSPW(3),
+
+		.lcdcon5	= S3C2410_LCDCON5_FRM565 |
+				  S3C2410_LCDCON5_INVVLINE |
+				  S3C2410_LCDCON5_INVVFRAME |
+				  S3C2410_LCDCON5_PWREN |
+				  S3C2410_LCDCON5_HWSWP,
+	},
+
+	.lpcsel		= ((0xCE6) & ~7) | 1<<4,
+
+	.width		= 240,
+	.height		= 320,
+
+	.xres		= {
+		.min	= 240,
+		.max	= 240,
+		.defval	= 240,
+	},
+
+	.yres		= {
+		.min	= 320,
+		.max	= 320,
+		.defval = 320,
+	},
+
+	.bpp		= {
+		.min	= 16,
+		.max	= 16,
+		.defval = 16,
+	},
+};
+
+/* CS8900 */
+
+static struct resource qt2410_cs89x0_resources[] = {
+	[0] = {
+		.start	= 0x19000000,
+		.end	= 0x19000000 + 16,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= IRQ_EINT9,
+		.end	= IRQ_EINT9,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device qt2410_cs89x0 = {
+	.name		= "cirrus-cs89x0",
+	.num_resources	= ARRAY_SIZE(qt2410_cs89x0_resources),
+	.resource	= qt2410_cs89x0_resources,
+};
+
+/* LED */
+
+static struct s3c24xx_led_platdata qt2410_pdata_led = {
+	.gpio		= S3C2410_GPB0,
+	.flags		= S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE,
+	.name		= "led",
+	.def_trigger	= "timer",
+};
+
+static struct platform_device qt2410_led = {
+	.name		= "s3c24xx_led",
+	.id		= 0,
+	.dev		= {
+		.platform_data = &qt2410_pdata_led,
+	},
+};
+
+/* SPI */
+
+static void spi_gpio_cs(struct s3c2410_spigpio_info *spi, int cs)
+{
+	switch (cs) {
+	case BITBANG_CS_ACTIVE:
+		s3c2410_gpio_setpin(S3C2410_GPB5, 0);
+		break;
+	case BITBANG_CS_INACTIVE:
+		s3c2410_gpio_setpin(S3C2410_GPB5, 1);
+		break;
+	}
+}
+
+static struct s3c2410_spigpio_info spi_gpio_cfg = {
+	.pin_clk	= S3C2410_GPG7,
+	.pin_mosi	= S3C2410_GPG6,
+	.pin_miso	= S3C2410_GPG5,
+	.chip_select	= &spi_gpio_cs,
+};
+
+
+static struct platform_device qt2410_spi = {
+	.name		  = "s3c24xx-spi-gpio",
+	.id		  = 1,
+	.dev = {
+		.platform_data = &spi_gpio_cfg,
+	},
+};
+
+/* Board devices */
+
+static struct platform_device *qt2410_devices[] __initdata = {
+	&s3c_device_usb,
+	&s3c_device_lcd,
+	&s3c_device_wdt,
+	&s3c_device_i2c,
+	&s3c_device_iis,
+	&s3c_device_sdi,
+	&s3c_device_usbgadget,
+	&qt2410_spi,
+	&qt2410_cs89x0,
+	&qt2410_led,
+};
+
+static struct s3c24xx_board qt2410_board __initdata = {
+	.devices       = qt2410_devices,
+	.devices_count = ARRAY_SIZE(qt2410_devices)
+};
+
+static struct mtd_partition qt2410_nand_part[] = {
+	[0] = {
+		.name	= "U-Boot",
+		.size	= 0x30000,
+		.offset	= 0,
+	},
+	[1] = {
+		.name	= "U-Boot environment",
+		.offset = 0x30000,
+		.size	= 0x4000,
+	},
+	[2] = {
+		.name	= "kernel",
+		.offset = 0x34000,
+		.size	= SZ_2M,
+	},
+	[3] = {
+		.name	= "initrd",
+		.offset	= 0x234000,
+		.size	= SZ_4M,
+	},
+	[4] = {
+		.name	= "jffs2",
+		.offset = 0x634000,
+		.size	= 0x39cc000,
+	},
+};
+
+static struct s3c2410_nand_set qt2410_nand_sets[] = {
+	[0] = {
+		.name		= "NAND",
+		.nr_chips	= 1,
+		.nr_partitions	= ARRAY_SIZE(qt2410_nand_part),
+		.partitions	= qt2410_nand_part,
+	},
+};
+
+/* choose a set of timings which should suit most 512Mbit
+ * chips and beyond.
+ */
+
+static struct s3c2410_platform_nand qt2410_nand_info = {
+	.tacls		= 20,
+	.twrph0		= 60,
+	.twrph1		= 20,
+	.nr_sets	= ARRAY_SIZE(qt2410_nand_sets),
+	.sets		= qt2410_nand_sets,
+};
+
+/* UDC */
+
+static struct s3c2410_udc_mach_info qt2410_udc_cfg = {
+};
+
+static char tft_type = 's';
+
+static int __init qt2410_tft_setup(char *str)
+{
+	tft_type = str[0];
+	return 1;
+}
+
+__setup("tft=", qt2410_tft_setup);
+
+static void __init qt2410_map_io(void)
+{
+	s3c24xx_init_io(qt2410_iodesc, ARRAY_SIZE(qt2410_iodesc));
+	s3c24xx_init_clocks(12*1000*1000);
+	s3c24xx_init_uarts(smdk2410_uartcfgs, ARRAY_SIZE(smdk2410_uartcfgs));
+	s3c24xx_set_board(&qt2410_board);
+}
+
+static void __init qt2410_machine_init(void)
+{
+	s3c_device_nand.dev.platform_data = &qt2410_nand_info;
+
+	switch (tft_type) {
+	case 'p': /* production */
+		s3c24xx_fb_set_platdata(&qt2410_prodlcd_cfg);
+		break;
+	case 'b': /* big */
+		s3c24xx_fb_set_platdata(&qt2410_biglcd_cfg);
+		break;
+	case 's': /* small */
+	default:
+		s3c24xx_fb_set_platdata(&qt2410_lcd_cfg);
+		break;
+	}
+
+	s3c2410_gpio_cfgpin(S3C2410_GPB0, S3C2410_GPIO_OUTPUT);
+	s3c2410_gpio_setpin(S3C2410_GPB0, 1);
+
+	s3c24xx_udc_set_platdata(&qt2410_udc_cfg);
+
+	s3c2410_gpio_cfgpin(S3C2410_GPB5, S3C2410_GPIO_OUTPUT);
+
+	s3c2410_pm_init();
+}
+
+MACHINE_START(QT2410, "QT2410")
+	.phys_io	= S3C2410_PA_UART,
+	.io_pg_offst	= (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc,
+	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+	.map_io		= qt2410_map_io,
+	.init_irq	= s3c24xx_init_irq,
+	.init_machine	= qt2410_machine_init,
+	.timer		= &s3c24xx_timer,
+MACHINE_END
+
+
diff --git a/arch/arm/mach-s3c2410/mach-smdk2410.c b/arch/arm/mach-s3c2410/mach-smdk2410.c
index 01c0c986d82..57b8a80f33d 100644
--- a/arch/arm/mach-s3c2410/mach-smdk2410.c
+++ b/arch/arm/mach-s3c2410/mach-smdk2410.c
@@ -1,4 +1,4 @@
-/***********************************************************************
+/* linux/arch/arm/mach-s3c2410/mach-smdk2410.c
  *
  * linux/arch/arm/mach-s3c2410/mach-smdk2410.c
  *
@@ -49,10 +49,10 @@
 
 #include <asm/arch/regs-serial.h>
 
-#include "devs.h"
-#include "cpu.h"
+#include <asm/plat-s3c24xx/devs.h>
+#include <asm/plat-s3c24xx/cpu.h>
 
-#include "common-smdk.h"
+#include <asm/plat-s3c24xx/common-smdk.h>
 
 static struct map_desc smdk2410_iodesc[] __initdata = {
   /* nothing here yet */
diff --git a/arch/arm/mach-s3c2410/mach-vr1000.c b/arch/arm/mach-s3c2410/mach-vr1000.c
index a382fc09511..c947c75bcbf 100644
--- a/arch/arm/mach-s3c2410/mach-vr1000.c
+++ b/arch/arm/mach-s3c2410/mach-vr1000.c
@@ -43,9 +43,9 @@
 #include <asm/arch/regs-gpio.h>
 #include <asm/arch/leds-gpio.h>
 
-#include "clock.h"
-#include "devs.h"
-#include "cpu.h"
+#include <asm/plat-s3c24xx/clock.h>
+#include <asm/plat-s3c24xx/devs.h>
+#include <asm/plat-s3c24xx/cpu.h>
 #include "usb-simtec.h"
 
 /* macros for virtual address mods for the io space entries */
diff --git a/arch/arm/mach-s3c2410/pm.c b/arch/arm/mach-s3c2410/pm.c
index ebf294dd31d..3b3a7db4e0d 100644
--- a/arch/arm/mach-s3c2410/pm.c
+++ b/arch/arm/mach-s3c2410/pm.c
@@ -1,11 +1,9 @@
 /* linux/arch/arm/mach-s3c2410/pm.c
  *
- * Copyright (c) 2004,2006 Simtec Electronics
+ * Copyright (c) 2006 Simtec Electronics
  *	Ben Dooks <ben@simtec.co.uk>
  *
- * S3C24XX Power Manager (Suspend-To-RAM) support
- *
- * See Documentation/arm/Samsung-S3C24XX/Suspend.txt for more information
+ * S3C2410 (and compatible) Power Manager (Suspend-To-RAM) support
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
@@ -20,640 +18,139 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- *
- * Parts based on arch/arm/mach-pxa/pm.c
- *
- * Thanks to Dimitry Andric for debugging
 */
 
 #include <linux/init.h>
 #include <linux/suspend.h>
 #include <linux/errno.h>
 #include <linux/time.h>
-#include <linux/interrupt.h>
-#include <linux/crc32.h>
-#include <linux/ioport.h>
-#include <linux/delay.h>
-#include <linux/serial_core.h>
+#include <linux/sysdev.h>
 
-#include <asm/cacheflush.h>
 #include <asm/hardware.h>
 #include <asm/io.h>
 
-#include <asm/arch/regs-serial.h>
-#include <asm/arch/regs-clock.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/regs-mem.h>
-#include <asm/arch/regs-irq.h>
-
-#include <asm/mach/time.h>
-
-#include "pm.h"
-
-/* for external use */
-
-unsigned long s3c_pm_flags;
-
-#define PFX "s3c24xx-pm: "
-
-static struct sleep_save core_save[] = {
-	SAVE_ITEM(S3C2410_LOCKTIME),
-	SAVE_ITEM(S3C2410_CLKCON),
-
-	/* we restore the timings here, with the proviso that the board
-	 * brings the system up in an slower, or equal frequency setting
-	 * to the original system.
-	 *
-	 * if we cannot guarantee this, then things are going to go very
-	 * wrong here, as we modify the refresh and both pll settings.
-	 */
-
-	SAVE_ITEM(S3C2410_BWSCON),
-	SAVE_ITEM(S3C2410_BANKCON0),
-	SAVE_ITEM(S3C2410_BANKCON1),
-	SAVE_ITEM(S3C2410_BANKCON2),
-	SAVE_ITEM(S3C2410_BANKCON3),
-	SAVE_ITEM(S3C2410_BANKCON4),
-	SAVE_ITEM(S3C2410_BANKCON5),
-
-	SAVE_ITEM(S3C2410_CLKDIVN),
-	SAVE_ITEM(S3C2410_MPLLCON),
-	SAVE_ITEM(S3C2410_UPLLCON),
-	SAVE_ITEM(S3C2410_CLKSLOW),
-	SAVE_ITEM(S3C2410_REFRESH),
-};
-
-static struct sleep_save gpio_save[] = {
-	SAVE_ITEM(S3C2410_GPACON),
-	SAVE_ITEM(S3C2410_GPADAT),
-
-	SAVE_ITEM(S3C2410_GPBCON),
-	SAVE_ITEM(S3C2410_GPBDAT),
-	SAVE_ITEM(S3C2410_GPBUP),
-
-	SAVE_ITEM(S3C2410_GPCCON),
-	SAVE_ITEM(S3C2410_GPCDAT),
-	SAVE_ITEM(S3C2410_GPCUP),
-
-	SAVE_ITEM(S3C2410_GPDCON),
-	SAVE_ITEM(S3C2410_GPDDAT),
-	SAVE_ITEM(S3C2410_GPDUP),
-
-	SAVE_ITEM(S3C2410_GPECON),
-	SAVE_ITEM(S3C2410_GPEDAT),
-	SAVE_ITEM(S3C2410_GPEUP),
-
-	SAVE_ITEM(S3C2410_GPFCON),
-	SAVE_ITEM(S3C2410_GPFDAT),
-	SAVE_ITEM(S3C2410_GPFUP),
+#include <asm/mach-types.h>
 
-	SAVE_ITEM(S3C2410_GPGCON),
-	SAVE_ITEM(S3C2410_GPGDAT),
-	SAVE_ITEM(S3C2410_GPGUP),
-
-	SAVE_ITEM(S3C2410_GPHCON),
-	SAVE_ITEM(S3C2410_GPHDAT),
-	SAVE_ITEM(S3C2410_GPHUP),
+#include <asm/arch/regs-gpio.h>
+#include <asm/arch/h1940.h>
 
-	SAVE_ITEM(S3C2410_DCLKCON),
-};
+#include <asm/plat-s3c24xx/cpu.h>
+#include <asm/plat-s3c24xx/pm.h>
 
 #ifdef CONFIG_S3C2410_PM_DEBUG
-
-#define SAVE_UART(va) \
-	SAVE_ITEM((va) + S3C2410_ULCON), \
-	SAVE_ITEM((va) + S3C2410_UCON), \
-	SAVE_ITEM((va) + S3C2410_UFCON), \
-	SAVE_ITEM((va) + S3C2410_UMCON), \
-	SAVE_ITEM((va) + S3C2410_UBRDIV)
-
-static struct sleep_save uart_save[] = {
-	SAVE_UART(S3C24XX_VA_UART0),
-	SAVE_UART(S3C24XX_VA_UART1),
-#ifndef CONFIG_CPU_S3C2400
-	SAVE_UART(S3C24XX_VA_UART2),
-#endif
-};
-
-/* debug
- *
- * we send the debug to printascii() to allow it to be seen if the
- * system never wakes up from the sleep
-*/
-
-extern void printascii(const char *);
-
-void pm_dbg(const char *fmt, ...)
-{
-	va_list va;
-	char buff[256];
-
-	va_start(va, fmt);
-	vsprintf(buff, fmt, va);
-	va_end(va);
-
-	printascii(buff);
-}
-
-static void s3c2410_pm_debug_init(void)
-{
-	unsigned long tmp = __raw_readl(S3C2410_CLKCON);
-
-	/* re-start uart clocks */
-	tmp |= S3C2410_CLKCON_UART0;
-	tmp |= S3C2410_CLKCON_UART1;
-	tmp |= S3C2410_CLKCON_UART2;
-
-	__raw_writel(tmp, S3C2410_CLKCON);
-	udelay(10);
-}
-
+extern void pm_dbg(const char *fmt, ...);
 #define DBG(fmt...) pm_dbg(fmt)
 #else
 #define DBG(fmt...) printk(KERN_DEBUG fmt)
-
-#define s3c2410_pm_debug_init() do { } while(0)
-
-static struct sleep_save uart_save[] = {};
 #endif
 
-#if defined(CONFIG_S3C2410_PM_CHECK) && CONFIG_S3C2410_PM_CHECK_CHUNKSIZE != 0
-
-/* suspend checking code...
- *
- * this next area does a set of crc checks over all the installed
- * memory, so the system can verify if the resume was ok.
- *
- * CONFIG_S3C2410_PM_CHECK_CHUNKSIZE defines the block-size for the CRC,
- * increasing it will mean that the area corrupted will be less easy to spot,
- * and reducing the size will cause the CRC save area to grow
-*/
-
-#define CHECK_CHUNKSIZE (CONFIG_S3C2410_PM_CHECK_CHUNKSIZE * 1024)
-
-static u32 crc_size;	/* size needed for the crc block */
-static u32 *crcs;	/* allocated over suspend/resume */
-
-typedef u32 *(run_fn_t)(struct resource *ptr, u32 *arg);
-
-/* s3c2410_pm_run_res
- *
- * go thorugh the given resource list, and look for system ram
-*/
-
-static void s3c2410_pm_run_res(struct resource *ptr, run_fn_t fn, u32 *arg)
-{
-	while (ptr != NULL) {
-		if (ptr->child != NULL)
-			s3c2410_pm_run_res(ptr->child, fn, arg);
-
-		if ((ptr->flags & IORESOURCE_MEM) &&
-		    strcmp(ptr->name, "System RAM") == 0) {
-			DBG("Found system RAM at %08lx..%08lx\n",
-			    ptr->start, ptr->end);
-			arg = (fn)(ptr, arg);
-		}
-
-		ptr = ptr->sibling;
-	}
-}
-
-static void s3c2410_pm_run_sysram(run_fn_t fn, u32 *arg)
-{
-	s3c2410_pm_run_res(&iomem_resource, fn, arg);
-}
-
-static u32 *s3c2410_pm_countram(struct resource *res, u32 *val)
-{
-	u32 size = (u32)(res->end - res->start)+1;
-
-	size += CHECK_CHUNKSIZE-1;
-	size /= CHECK_CHUNKSIZE;
-
-	DBG("Area %08lx..%08lx, %d blocks\n", res->start, res->end, size);
-
-	*val += size * sizeof(u32);
-	return val;
-}
-
-/* s3c2410_pm_prepare_check
- *
- * prepare the necessary information for creating the CRCs. This
- * must be done before the final save, as it will require memory
- * allocating, and thus touching bits of the kernel we do not
- * know about.
-*/
-
-static void s3c2410_pm_check_prepare(void)
+static void s3c2410_pm_prepare(void)
 {
-	crc_size = 0;
+	/* ensure at least GSTATUS3 has the resume address */
 
-	s3c2410_pm_run_sysram(s3c2410_pm_countram, &crc_size);
+	__raw_writel(virt_to_phys(s3c2410_cpu_resume), S3C2410_GSTATUS3);
 
-	DBG("s3c2410_pm_prepare_check: %u checks needed\n", crc_size);
+	DBG("GSTATUS3 0x%08x\n", __raw_readl(S3C2410_GSTATUS3));
+	DBG("GSTATUS4 0x%08x\n", __raw_readl(S3C2410_GSTATUS4));
 
-	crcs = kmalloc(crc_size+4, GFP_KERNEL);
-	if (crcs == NULL)
-		printk(KERN_ERR "Cannot allocated CRC save area\n");
-}
+	if (machine_is_h1940()) {
+		void *base = phys_to_virt(H1940_SUSPEND_CHECK);
+		unsigned long ptr;
+		unsigned long calc = 0;
 
-static u32 *s3c2410_pm_makecheck(struct resource *res, u32 *val)
-{
-	unsigned long addr, left;
+		/* generate check for the bootloader to check on resume */
 
-	for (addr = res->start; addr < res->end;
-	     addr += CHECK_CHUNKSIZE) {
-		left = res->end - addr;
+		for (ptr = 0; ptr < 0x40000; ptr += 0x400)
+			calc += __raw_readl(base+ptr);
 
-		if (left > CHECK_CHUNKSIZE)
-			left = CHECK_CHUNKSIZE;
-
-		*val = crc32_le(~0, phys_to_virt(addr), left);
-		val++;
+		__raw_writel(calc, phys_to_virt(H1940_SUSPEND_CHECKSUM));
 	}
 
-	return val;
-}
-
-/* s3c2410_pm_check_store
- *
- * compute the CRC values for the memory blocks before the final
- * sleep.
-*/
-
-static void s3c2410_pm_check_store(void)
-{
-	if (crcs != NULL)
-		s3c2410_pm_run_sysram(s3c2410_pm_makecheck, crcs);
-}
-
-/* in_region
- *
- * return TRUE if the area defined by ptr..ptr+size contatins the
- * what..what+whatsz
-*/
-
-static inline int in_region(void *ptr, int size, void *what, size_t whatsz)
-{
-	if ((what+whatsz) < ptr)
-		return 0;
-
-	if (what > (ptr+size))
-		return 0;
-
-	return 1;
-}
-
-static u32 *s3c2410_pm_runcheck(struct resource *res, u32 *val)
-{
-	void *save_at = phys_to_virt(s3c2410_sleep_save_phys);
-	unsigned long addr;
-	unsigned long left;
-	void *ptr;
-	u32 calc;
-
-	for (addr = res->start; addr < res->end;
-	     addr += CHECK_CHUNKSIZE) {
-		left = res->end - addr;
+	/* the RX3715 uses similar code and the same H1940 and the
+	 * same offsets for resume and checksum pointers */
 
-		if (left > CHECK_CHUNKSIZE)
-			left = CHECK_CHUNKSIZE;
+	if (machine_is_rx3715()) {
+		void *base = phys_to_virt(H1940_SUSPEND_CHECK);
+		unsigned long ptr;
+		unsigned long calc = 0;
 
-		ptr = phys_to_virt(addr);
+		/* generate check for the bootloader to check on resume */
 
-		if (in_region(ptr, left, crcs, crc_size)) {
-			DBG("skipping %08lx, has crc block in\n", addr);
-			goto skip_check;
-		}
+		for (ptr = 0; ptr < 0x40000; ptr += 0x4)
+			calc += __raw_readl(base+ptr);
 
-		if (in_region(ptr, left, save_at, 32*4 )) {
-			DBG("skipping %08lx, has save block in\n", addr);
-			goto skip_check;
-		}
-
-		/* calculate and check the checksum */
-
-		calc = crc32_le(~0, ptr, left);
-		if (calc != *val) {
-			printk(KERN_ERR PFX "Restore CRC error at "
-			       "%08lx (%08x vs %08x)\n", addr, calc, *val);
-
-			DBG("Restore CRC error at %08lx (%08x vs %08x)\n",
-			    addr, calc, *val);
-		}
-
-	skip_check:
-		val++;
+		__raw_writel(calc, phys_to_virt(H1940_SUSPEND_CHECKSUM));
 	}
 
-	return val;
-}
+	if ( machine_is_aml_m5900() )
+		s3c2410_gpio_setpin(S3C2410_GPF2, 1);
 
-/* s3c2410_pm_check_restore
- *
- * check the CRCs after the restore event and free the memory used
- * to hold them
-*/
-
-static void s3c2410_pm_check_restore(void)
-{
-	if (crcs != NULL) {
-		s3c2410_pm_run_sysram(s3c2410_pm_runcheck, crcs);
-		kfree(crcs);
-		crcs = NULL;
-	}
 }
 
-#else
-
-#define s3c2410_pm_check_prepare() do { } while(0)
-#define s3c2410_pm_check_restore() do { } while(0)
-#define s3c2410_pm_check_store()   do { } while(0)
-#endif
-
-/* helper functions to save and restore register state */
-
-void s3c2410_pm_do_save(struct sleep_save *ptr, int count)
+static int s3c2410_pm_resume(struct sys_device *dev)
 {
-	for (; count > 0; count--, ptr++) {
-		ptr->val = __raw_readl(ptr->reg);
-		DBG("saved %p value %08lx\n", ptr->reg, ptr->val);
-	}
-}
+	unsigned long tmp;
 
-/* s3c2410_pm_do_restore
- *
- * restore the system from the given list of saved registers
- *
- * Note, we do not use DBG() in here, as the system may not have
- * restore the UARTs state yet
-*/
+	/* unset the return-from-sleep flag, to ensure reset */
 
-void s3c2410_pm_do_restore(struct sleep_save *ptr, int count)
-{
-	for (; count > 0; count--, ptr++) {
-		printk(KERN_DEBUG "restore %p (restore %08lx, was %08x)\n",
-		       ptr->reg, ptr->val, __raw_readl(ptr->reg));
-
-		__raw_writel(ptr->val, ptr->reg);
-	}
-}
+	tmp = __raw_readl(S3C2410_GSTATUS2);
+	tmp &= S3C2410_GSTATUS2_OFFRESET;
+	__raw_writel(tmp, S3C2410_GSTATUS2);
 
-/* s3c2410_pm_do_restore_core
- *
- * similar to s3c2410_pm_do_restore_core
- *
- * WARNING: Do not put any debug in here that may effect memory or use
- * peripherals, as things may be changing!
-*/
+	if ( machine_is_aml_m5900() )
+		s3c2410_gpio_setpin(S3C2410_GPF2, 0);
 
-static void s3c2410_pm_do_restore_core(struct sleep_save *ptr, int count)
-{
-	for (; count > 0; count--, ptr++) {
-		__raw_writel(ptr->val, ptr->reg);
-	}
+	return 0;
 }
 
-/* s3c2410_pm_show_resume_irqs
- *
- * print any IRQs asserted at resume time (ie, we woke from)
-*/
-
-static void s3c2410_pm_show_resume_irqs(int start, unsigned long which,
-					unsigned long mask)
+static int s3c2410_pm_add(struct sys_device *dev)
 {
-	int i;
+	pm_cpu_prep = s3c2410_pm_prepare;
+	pm_cpu_sleep = s3c2410_cpu_suspend;
 
-	which &= ~mask;
-
-	for (i = 0; i <= 31; i++) {
-		if ((which) & (1L<<i)) {
-			DBG("IRQ %d asserted at resume\n", start+i);
-		}
-	}
+	return 0;
 }
 
-/* s3c2410_pm_check_resume_pin
- *
- * check to see if the pin is configured correctly for sleep mode, and
- * make any necessary adjustments if it is not
-*/
-
-static void s3c2410_pm_check_resume_pin(unsigned int pin, unsigned int irqoffs)
-{
-	unsigned long irqstate;
-	unsigned long pinstate;
-	int irq = s3c2410_gpio_getirq(pin);
-
-	if (irqoffs < 4)
-		irqstate = s3c_irqwake_intmask & (1L<<irqoffs);
-	else
-		irqstate = s3c_irqwake_eintmask & (1L<<irqoffs);
-
-	pinstate = s3c2410_gpio_getcfg(pin);
-
-	if (!irqstate) {
-		if (pinstate == S3C2410_GPIO_IRQ)
-			DBG("Leaving IRQ %d (pin %d) enabled\n", irq, pin);
-	} else {
-		if (pinstate == S3C2410_GPIO_IRQ) {
-			DBG("Disabling IRQ %d (pin %d)\n", irq, pin);
-			s3c2410_gpio_cfgpin(pin, S3C2410_GPIO_INPUT);
-		}
-	}
-}
+#if defined(CONFIG_CPU_S3C2410)
+static struct sysdev_driver s3c2410_pm_driver = {
+	.add		= s3c2410_pm_add,
+	.resume		= s3c2410_pm_resume,
+};
 
-/* s3c2410_pm_configure_extint
- *
- * configure all external interrupt pins
-*/
+/* register ourselves */
 
-static void s3c2410_pm_configure_extint(void)
+static int __init s3c2410_pm_drvinit(void)
 {
-	int pin;
-
-	/* for each of the external interrupts (EINT0..EINT15) we
-	 * need to check wether it is an external interrupt source,
-	 * and then configure it as an input if it is not
-	*/
-
-	for (pin = S3C2410_GPF0; pin <= S3C2410_GPF7; pin++) {
-		s3c2410_pm_check_resume_pin(pin, pin - S3C2410_GPF0);
-	}
-
-	for (pin = S3C2410_GPG0; pin <= S3C2410_GPG7; pin++) {
-		s3c2410_pm_check_resume_pin(pin, (pin - S3C2410_GPG0)+8);
-	}
+	return sysdev_driver_register(&s3c2410_sysclass, &s3c2410_pm_driver);
 }
 
-void (*pm_cpu_prep)(void);
-void (*pm_cpu_sleep)(void);
-
-#define any_allowed(mask, allow) (((mask) & (allow)) != (allow))
-
-/* s3c2410_pm_enter
- *
- * central control for sleep/resume process
-*/
-
-static int s3c2410_pm_enter(suspend_state_t state)
-{
-	unsigned long regs_save[16];
-
-	/* ensure the debug is initialised (if enabled) */
-
-	s3c2410_pm_debug_init();
-
-	DBG("s3c2410_pm_enter(%d)\n", state);
-
-	if (pm_cpu_prep == NULL || pm_cpu_sleep == NULL) {
-		printk(KERN_ERR PFX "error: no cpu sleep functions set\n");
-		return -EINVAL;
-	}
-
-	if (state != PM_SUSPEND_MEM) {
-		printk(KERN_ERR PFX "error: only PM_SUSPEND_MEM supported\n");
-		return -EINVAL;
-	}
-
-	/* check if we have anything to wake-up with... bad things seem
-	 * to happen if you suspend with no wakeup (system will often
-	 * require a full power-cycle)
-	*/
-
-	if (!any_allowed(s3c_irqwake_intmask, s3c_irqwake_intallow) &&
-	    !any_allowed(s3c_irqwake_eintmask, s3c_irqwake_eintallow)) {
-		printk(KERN_ERR PFX "No sources enabled for wake-up!\n");
-		printk(KERN_ERR PFX "Aborting sleep\n");
-		return -EINVAL;
-	}
-
-	/* prepare check area if configured */
-
-	s3c2410_pm_check_prepare();
-
-	/* store the physical address of the register recovery block */
-
-	s3c2410_sleep_save_phys = virt_to_phys(regs_save);
-
-	DBG("s3c2410_sleep_save_phys=0x%08lx\n", s3c2410_sleep_save_phys);
-
-	/* save all necessary core registers not covered by the drivers */
-
-	s3c2410_pm_do_save(gpio_save, ARRAY_SIZE(gpio_save));
-	s3c2410_pm_do_save(core_save, ARRAY_SIZE(core_save));
-	s3c2410_pm_do_save(uart_save, ARRAY_SIZE(uart_save));
-
-	/* set the irq configuration for wake */
-
-	s3c2410_pm_configure_extint();
-
-	DBG("sleep: irq wakeup masks: %08lx,%08lx\n",
-	    s3c_irqwake_intmask, s3c_irqwake_eintmask);
-
-	__raw_writel(s3c_irqwake_intmask, S3C2410_INTMSK);
-	__raw_writel(s3c_irqwake_eintmask, S3C2410_EINTMASK);
-
-	/* ack any outstanding external interrupts before we go to sleep */
-
-	__raw_writel(__raw_readl(S3C2410_EINTPEND), S3C2410_EINTPEND);
-	__raw_writel(__raw_readl(S3C2410_INTPND), S3C2410_INTPND);
-	__raw_writel(__raw_readl(S3C2410_SRCPND), S3C2410_SRCPND);
-
-	/* call cpu specific preperation */
-
-	pm_cpu_prep();
-
-	/* flush cache back to ram */
-
-	flush_cache_all();
-
-	s3c2410_pm_check_store();
-
-	/* send the cpu to sleep... */
-
-	__raw_writel(0x00, S3C2410_CLKCON);  /* turn off clocks over sleep */
-
-	/* s3c2410_cpu_save will also act as our return point from when
-	 * we resume as it saves its own register state, so use the return
-	 * code to differentiate return from save and return from sleep */
-
-	if (s3c2410_cpu_save(regs_save) == 0) {
-		flush_cache_all();
-		pm_cpu_sleep();
-	}
-
-	/* restore the cpu state */
-
-	cpu_init();
-
-	/* restore the system state */
-
-	s3c2410_pm_do_restore_core(core_save, ARRAY_SIZE(core_save));
-	s3c2410_pm_do_restore(gpio_save, ARRAY_SIZE(gpio_save));
-	s3c2410_pm_do_restore(uart_save, ARRAY_SIZE(uart_save));
-
-	s3c2410_pm_debug_init();
-
-	/* check what irq (if any) restored the system */
-
-	DBG("post sleep: IRQs 0x%08x, 0x%08x\n",
-	    __raw_readl(S3C2410_SRCPND),
-	    __raw_readl(S3C2410_EINTPEND));
-
-	s3c2410_pm_show_resume_irqs(IRQ_EINT0, __raw_readl(S3C2410_SRCPND),
-				    s3c_irqwake_intmask);
-
-	s3c2410_pm_show_resume_irqs(IRQ_EINT4-4, __raw_readl(S3C2410_EINTPEND),
-				    s3c_irqwake_eintmask);
-
-	DBG("post sleep, preparing to return\n");
-
-	s3c2410_pm_check_restore();
-
-	/* ok, let's return from sleep */
+arch_initcall(s3c2410_pm_drvinit);
+#endif
 
-	DBG("S3C2410 PM Resume (post-restore)\n");
-	return 0;
-}
+#if defined(CONFIG_CPU_S3C2440)
+static struct sysdev_driver s3c2440_pm_driver = {
+	.add		= s3c2410_pm_add,
+	.resume		= s3c2410_pm_resume,
+};
 
-/*
- * Called after processes are frozen, but before we shut down devices.
- */
-static int s3c2410_pm_prepare(suspend_state_t state)
+static int __init s3c2440_pm_drvinit(void)
 {
-	return 0;
+	return sysdev_driver_register(&s3c2440_sysclass, &s3c2440_pm_driver);
 }
 
-/*
- * Called after devices are re-setup, but before processes are thawed.
- */
-static int s3c2410_pm_finish(suspend_state_t state)
-{
-	return 0;
-}
+arch_initcall(s3c2440_pm_drvinit);
+#endif
 
-/*
- * Set to PM_DISK_FIRMWARE so we can quickly veto suspend-to-disk.
- */
-static struct pm_ops s3c2410_pm_ops = {
-	.pm_disk_mode	= PM_DISK_FIRMWARE,
-	.prepare	= s3c2410_pm_prepare,
-	.enter		= s3c2410_pm_enter,
-	.finish		= s3c2410_pm_finish,
+#if defined(CONFIG_CPU_S3C2442)
+static struct sysdev_driver s3c2442_pm_driver = {
+	.add		= s3c2410_pm_add,
+	.resume		= s3c2410_pm_resume,
 };
 
-/* s3c2410_pm_init
- *
- * Attach the power management functions. This should be called
- * from the board specific initialisation if the board supports
- * it.
-*/
-
-int __init s3c2410_pm_init(void)
+static int __init s3c2442_pm_drvinit(void)
 {
-	printk("S3C2410 Power Management, (c) 2004 Simtec Electronics\n");
-
-	pm_set_ops(&s3c2410_pm_ops);
-	return 0;
+	return sysdev_driver_register(&s3c2442_sysclass, &s3c2442_pm_driver);
 }
+
+arch_initcall(s3c2442_pm_drvinit);
+#endif
diff --git a/arch/arm/mach-s3c2410/pm.h b/arch/arm/mach-s3c2410/pm.h
deleted file mode 100644
index ffe197a119f..00000000000
--- a/arch/arm/mach-s3c2410/pm.h
+++ /dev/null
@@ -1,73 +0,0 @@
-/* linux/arch/arm/mach-s3c2410/pm.h
- *
- * Copyright (c) 2004 Simtec Electronics
- *	Written by Ben Dooks, <ben@simtec.co.uk>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-/* s3c2410_pm_init
- *
- * called from board at initialisation time to setup the power
- * management
-*/
-
-#ifdef CONFIG_PM
-
-extern __init int s3c2410_pm_init(void);
-
-#else
-
-static inline int s3c2410_pm_init(void)
-{
-	return 0;
-}
-#endif
-
-/* configuration for the IRQ mask over sleep */
-extern unsigned long s3c_irqwake_intmask;
-extern unsigned long s3c_irqwake_eintmask;
-
-/* IRQ masks for IRQs allowed to go to sleep (see irq.c) */
-extern unsigned long s3c_irqwake_intallow;
-extern unsigned long s3c_irqwake_eintallow;
-
-/* per-cpu sleep functions */
-
-extern void (*pm_cpu_prep)(void);
-extern void (*pm_cpu_sleep)(void);
-
-/* Flags for PM Control */
-
-extern unsigned long s3c_pm_flags;
-
-/* from sleep.S */
-
-extern int  s3c2410_cpu_save(unsigned long *saveblk);
-extern void s3c2410_cpu_suspend(void);
-extern void s3c2410_cpu_resume(void);
-
-extern unsigned long s3c2410_sleep_save_phys;
-
-/* sleep save info */
-
-struct sleep_save {
-	void __iomem	*reg;
-	unsigned long	val;
-};
-
-#define SAVE_ITEM(x) \
-	{ .reg = (x) }
-
-extern void s3c2410_pm_do_save(struct sleep_save *ptr, int count);
-extern void s3c2410_pm_do_restore(struct sleep_save *ptr, int count);
-
-#ifdef CONFIG_PM
-extern int s3c24xx_irq_suspend(struct sys_device *dev, pm_message_t state);
-extern int s3c24xx_irq_resume(struct sys_device *dev);
-#else
-#define s3c24xx_irq_suspend NULL
-#define s3c24xx_irq_resume  NULL
-#endif
diff --git a/arch/arm/mach-s3c2410/s3c2400.h b/arch/arm/mach-s3c2410/s3c2400.h
deleted file mode 100644
index 8b2394e1ed4..00000000000
--- a/arch/arm/mach-s3c2410/s3c2400.h
+++ /dev/null
@@ -1,31 +0,0 @@
-/* arch/arm/mach-s3c2410/s3c2400.h
- *
- * Copyright (c) 2004 Simtec Electronics
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * Header file for S3C2400 cpu support
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * Modifications:
- *     09-Fev-2006 LCVR  First version, based on s3c2410.h
-*/
-
-#ifdef CONFIG_CPU_S3C2400
-
-extern  int s3c2400_init(void);
-
-extern void s3c2400_map_io(struct map_desc *mach_desc, int size);
-
-extern void s3c2400_init_uarts(struct s3c2410_uartcfg *cfg, int no);
-
-extern void s3c2400_init_clocks(int xtal);
-
-#else
-#define s3c2400_init_clocks NULL
-#define s3c2400_init_uarts NULL
-#define s3c2400_map_io NULL
-#define s3c2400_init NULL
-#endif
diff --git a/arch/arm/mach-s3c2410/s3c2410-clock.c b/arch/arm/mach-s3c2410/s3c2410-clock.c
deleted file mode 100644
index 992cc6af230..00000000000
--- a/arch/arm/mach-s3c2410/s3c2410-clock.c
+++ /dev/null
@@ -1,276 +0,0 @@
-/* linux/arch/arm/mach-s3c2410/s3c2410-clock.c
- *
- * Copyright (c) 2006 Simtec Electronics
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * S3C2410,S3C2440,S3C2442 Clock control support
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
-*/
-
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/list.h>
-#include <linux/errno.h>
-#include <linux/err.h>
-#include <linux/sysdev.h>
-#include <linux/clk.h>
-#include <linux/mutex.h>
-#include <linux/delay.h>
-#include <linux/serial_core.h>
-
-#include <asm/mach/map.h>
-
-#include <asm/hardware.h>
-#include <asm/io.h>
-
-#include <asm/arch/regs-serial.h>
-#include <asm/arch/regs-clock.h>
-#include <asm/arch/regs-gpio.h>
-
-#include "s3c2410.h"
-#include "clock.h"
-#include "cpu.h"
-
-int s3c2410_clkcon_enable(struct clk *clk, int enable)
-{
-	unsigned int clocks = clk->ctrlbit;
-	unsigned long clkcon;
-
-	clkcon = __raw_readl(S3C2410_CLKCON);
-
-	if (enable)
-		clkcon |= clocks;
-	else
-		clkcon &= ~clocks;
-
-	/* ensure none of the special function bits set */
-	clkcon &= ~(S3C2410_CLKCON_IDLE|S3C2410_CLKCON_POWER);
-
-	__raw_writel(clkcon, S3C2410_CLKCON);
-
-	return 0;
-}
-
-static int s3c2410_upll_enable(struct clk *clk, int enable)
-{
-	unsigned long clkslow = __raw_readl(S3C2410_CLKSLOW);
-	unsigned long orig = clkslow;
-
-	if (enable)
-		clkslow &= ~S3C2410_CLKSLOW_UCLK_OFF;
-	else
-		clkslow |= S3C2410_CLKSLOW_UCLK_OFF;
-
-	__raw_writel(clkslow, S3C2410_CLKSLOW);
-
-	/* if we started the UPLL, then allow to settle */
-
-	if (enable && (orig & S3C2410_CLKSLOW_UCLK_OFF))
-		udelay(200);
-
-	return 0;
-}
-
-/* standard clock definitions */
-
-static struct clk init_clocks_disable[] = {
-	{
-		.name		= "nand",
-		.id		= -1,
-		.parent		= &clk_h,
-		.enable		= s3c2410_clkcon_enable,
-		.ctrlbit	= S3C2410_CLKCON_NAND,
-	}, {
-		.name		= "sdi",
-		.id		= -1,
-		.parent		= &clk_p,
-		.enable		= s3c2410_clkcon_enable,
-		.ctrlbit	= S3C2410_CLKCON_SDI,
-	}, {
-		.name		= "adc",
-		.id		= -1,
-		.parent		= &clk_p,
-		.enable		= s3c2410_clkcon_enable,
-		.ctrlbit	= S3C2410_CLKCON_ADC,
-	}, {
-		.name		= "i2c",
-		.id		= -1,
-		.parent		= &clk_p,
-		.enable		= s3c2410_clkcon_enable,
-		.ctrlbit	= S3C2410_CLKCON_IIC,
-	}, {
-		.name		= "iis",
-		.id		= -1,
-		.parent		= &clk_p,
-		.enable		= s3c2410_clkcon_enable,
-		.ctrlbit	= S3C2410_CLKCON_IIS,
-	}, {
-		.name		= "spi",
-		.id		= -1,
-		.parent		= &clk_p,
-		.enable		= s3c2410_clkcon_enable,
-		.ctrlbit	= S3C2410_CLKCON_SPI,
-	}
-};
-
-static struct clk init_clocks[] = {
-	{
-		.name		= "lcd",
-		.id		= -1,
-		.parent		= &clk_h,
-		.enable		= s3c2410_clkcon_enable,
-		.ctrlbit	= S3C2410_CLKCON_LCDC,
-	}, {
-		.name		= "gpio",
-		.id		= -1,
-		.parent		= &clk_p,
-		.enable		= s3c2410_clkcon_enable,
-		.ctrlbit	= S3C2410_CLKCON_GPIO,
-	}, {
-		.name		= "usb-host",
-		.id		= -1,
-		.parent		= &clk_h,
-		.enable		= s3c2410_clkcon_enable,
-		.ctrlbit	= S3C2410_CLKCON_USBH,
-	}, {
-		.name		= "usb-device",
-		.id		= -1,
-		.parent		= &clk_h,
-		.enable		= s3c2410_clkcon_enable,
-		.ctrlbit	= S3C2410_CLKCON_USBD,
-	}, {
-		.name		= "timers",
-		.id		= -1,
-		.parent		= &clk_p,
-		.enable		= s3c2410_clkcon_enable,
-		.ctrlbit	= S3C2410_CLKCON_PWMT,
-	}, {
-		.name		= "uart",
-		.id		= 0,
-		.parent		= &clk_p,
-		.enable		= s3c2410_clkcon_enable,
-		.ctrlbit	= S3C2410_CLKCON_UART0,
-	}, {
-		.name		= "uart",
-		.id		= 1,
-		.parent		= &clk_p,
-		.enable		= s3c2410_clkcon_enable,
-		.ctrlbit	= S3C2410_CLKCON_UART1,
-	}, {
-		.name		= "uart",
-		.id		= 2,
-		.parent		= &clk_p,
-		.enable		= s3c2410_clkcon_enable,
-		.ctrlbit	= S3C2410_CLKCON_UART2,
-	}, {
-		.name		= "rtc",
-		.id		= -1,
-		.parent		= &clk_p,
-		.enable		= s3c2410_clkcon_enable,
-		.ctrlbit	= S3C2410_CLKCON_RTC,
-	}, {
-		.name		= "watchdog",
-		.id		= -1,
-		.parent		= &clk_p,
-		.ctrlbit	= 0,
-	}, {
-		.name		= "usb-bus-host",
-		.id		= -1,
-		.parent		= &clk_usb_bus,
-	}, {
-		.name		= "usb-bus-gadget",
-		.id		= -1,
-		.parent		= &clk_usb_bus,
-	},
-};
-
-/* s3c2410_baseclk_add()
- *
- * Add all the clocks used by the s3c2410 or compatible CPUs
- * such as the S3C2440 and S3C2442.
- *
- * We cannot use a system device as we are needed before any
- * of the init-calls that initialise the devices are actually
- * done.
-*/
-
-int __init s3c2410_baseclk_add(void)
-{
-	unsigned long clkslow = __raw_readl(S3C2410_CLKSLOW);
-	unsigned long clkcon  = __raw_readl(S3C2410_CLKCON);
-	struct clk *clkp;
-	struct clk *xtal;
-	int ret;
-	int ptr;
-
-	clk_upll.enable = s3c2410_upll_enable;
-
-	if (s3c24xx_register_clock(&clk_usb_bus) < 0)
-		printk(KERN_ERR "failed to register usb bus clock\n");
-
-	/* register clocks from clock array */
-
-	clkp = init_clocks;
-	for (ptr = 0; ptr < ARRAY_SIZE(init_clocks); ptr++, clkp++) {
-		/* ensure that we note the clock state */
-
-		clkp->usage = clkcon & clkp->ctrlbit ? 1 : 0;
-
-		ret = s3c24xx_register_clock(clkp);
-		if (ret < 0) {
-			printk(KERN_ERR "Failed to register clock %s (%d)\n",
-			       clkp->name, ret);
-		}
-	}
-
-	/* We must be careful disabling the clocks we are not intending to
-	 * be using at boot time, as subsytems such as the LCD which do
-	 * their own DMA requests to the bus can cause the system to lockup
-	 * if they where in the middle of requesting bus access.
-	 *
-	 * Disabling the LCD clock if the LCD is active is very dangerous,
-	 * and therefore the bootloader should be careful to not enable
-	 * the LCD clock if it is not needed.
-	*/
-
-	/* install (and disable) the clocks we do not need immediately */
-
-	clkp = init_clocks_disable;
-	for (ptr = 0; ptr < ARRAY_SIZE(init_clocks_disable); ptr++, clkp++) {
-
-		ret = s3c24xx_register_clock(clkp);
-		if (ret < 0) {
-			printk(KERN_ERR "Failed to register clock %s (%d)\n",
-			       clkp->name, ret);
-		}
-
-		s3c2410_clkcon_enable(clkp, 0);
-	}
-
-	/* show the clock-slow value */
-
-	xtal = clk_get(NULL, "xtal");
-
-	printk("CLOCK: Slow mode (%ld.%ld MHz), %s, MPLL %s, UPLL %s\n",
-	       print_mhz(clk_get_rate(xtal) /
-			 ( 2 * S3C2410_CLKSLOW_GET_SLOWVAL(clkslow))),
-	       (clkslow & S3C2410_CLKSLOW_SLOW) ? "slow" : "fast",
-	       (clkslow & S3C2410_CLKSLOW_MPLL_OFF) ? "off" : "on",
-	       (clkslow & S3C2410_CLKSLOW_UCLK_OFF) ? "off" : "on");
-
-	return 0;
-}
diff --git a/arch/arm/mach-s3c2410/s3c2410-dma.c b/arch/arm/mach-s3c2410/s3c2410-dma.c
deleted file mode 100644
index e67ba3911f1..00000000000
--- a/arch/arm/mach-s3c2410/s3c2410-dma.c
+++ /dev/null
@@ -1,161 +0,0 @@
-/* linux/arch/arm/mach-s3c2410/s3c2410-dma.c
- *
- * Copyright (c) 2006 Simtec Electronics
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * S3C2410 DMA selection
- *
- * http://armlinux.simtec.co.uk/
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/sysdev.h>
-#include <linux/serial_core.h>
-
-#include <asm/dma.h>
-#include <asm/arch/dma.h>
-#include "dma.h"
-
-#include "cpu.h"
-
-#include <asm/arch/regs-serial.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/regs-ac97.h>
-#include <asm/arch/regs-mem.h>
-#include <asm/arch/regs-lcd.h>
-#include <asm/arch/regs-sdi.h>
-#include <asm/arch/regs-iis.h>
-#include <asm/arch/regs-spi.h>
-
-static struct s3c24xx_dma_map __initdata s3c2410_dma_mappings[] = {
-	[DMACH_XD0] = {
-		.name		= "xdreq0",
-		.channels[0]	= S3C2410_DCON_CH0_XDREQ0 | DMA_CH_VALID,
-	},
-	[DMACH_XD1] = {
-		.name		= "xdreq1",
-		.channels[1]	= S3C2410_DCON_CH1_XDREQ1 | DMA_CH_VALID,
-	},
-	[DMACH_SDI] = {
-		.name		= "sdi",
-		.channels[0]	= S3C2410_DCON_CH0_SDI | DMA_CH_VALID,
-		.channels[2]	= S3C2410_DCON_CH2_SDI | DMA_CH_VALID,
-		.channels[3]	= S3C2410_DCON_CH3_SDI | DMA_CH_VALID,
-		.hw_addr.to	= S3C2410_PA_IIS + S3C2410_IISFIFO,
-		.hw_addr.from	= S3C2410_PA_IIS + S3C2410_IISFIFO,
-	},
-	[DMACH_SPI0] = {
-		.name		= "spi0",
-		.channels[1]	= S3C2410_DCON_CH1_SPI | DMA_CH_VALID,
-		.hw_addr.to	= S3C2410_PA_SPI + S3C2410_SPTDAT,
-		.hw_addr.from	= S3C2410_PA_SPI + S3C2410_SPRDAT,
-	},
-	[DMACH_SPI1] = {
-		.name		= "spi1",
-		.channels[3]	= S3C2410_DCON_CH3_SPI | DMA_CH_VALID,
-		.hw_addr.to	= S3C2410_PA_SPI + 0x20 + S3C2410_SPTDAT,
-		.hw_addr.from	= S3C2410_PA_SPI + 0x20 + S3C2410_SPRDAT,
-	},
-	[DMACH_UART0] = {
-		.name		= "uart0",
-		.channels[0]	= S3C2410_DCON_CH0_UART0 | DMA_CH_VALID,
-		.hw_addr.to	= S3C2410_PA_UART0 + S3C2410_UTXH,
-		.hw_addr.from	= S3C2410_PA_UART0 + S3C2410_URXH,
-	},
-	[DMACH_UART1] = {
-		.name		= "uart1",
-		.channels[1]	= S3C2410_DCON_CH1_UART1 | DMA_CH_VALID,
-		.hw_addr.to	= S3C2410_PA_UART1 + S3C2410_UTXH,
-		.hw_addr.from	= S3C2410_PA_UART1 + S3C2410_URXH,
-	},
-      	[DMACH_UART2] = {
-		.name		= "uart2",
-		.channels[3]	= S3C2410_DCON_CH3_UART2 | DMA_CH_VALID,
-		.hw_addr.to	= S3C2410_PA_UART2 + S3C2410_UTXH,
-		.hw_addr.from	= S3C2410_PA_UART2 + S3C2410_URXH,
-	},
-	[DMACH_TIMER] = {
-		.name		= "timer",
-		.channels[0]	= S3C2410_DCON_CH0_TIMER | DMA_CH_VALID,
-		.channels[2]	= S3C2410_DCON_CH2_TIMER | DMA_CH_VALID,
-		.channels[3]	= S3C2410_DCON_CH3_TIMER | DMA_CH_VALID,
-	},
-	[DMACH_I2S_IN] = {
-		.name		= "i2s-sdi",
-		.channels[1]	= S3C2410_DCON_CH1_I2SSDI | DMA_CH_VALID,
-		.channels[2]	= S3C2410_DCON_CH2_I2SSDI | DMA_CH_VALID,
-		.hw_addr.from	= S3C2410_PA_IIS + S3C2410_IISFIFO,
-	},
-	[DMACH_I2S_OUT] = {
-		.name		= "i2s-sdo",
-		.channels[2]	= S3C2410_DCON_CH2_I2SSDO | DMA_CH_VALID,
-		.hw_addr.to	= S3C2410_PA_IIS + S3C2410_IISFIFO,
-	},
-	[DMACH_USB_EP1] = {
-		.name		= "usb-ep1",
-		.channels[0]	= S3C2410_DCON_CH0_USBEP1 | DMA_CH_VALID,
-	},
-	[DMACH_USB_EP2] = {
-		.name		= "usb-ep2",
-		.channels[1]	= S3C2410_DCON_CH1_USBEP2 | DMA_CH_VALID,
-	},
-	[DMACH_USB_EP3] = {
-		.name		= "usb-ep3",
-		.channels[2]	= S3C2410_DCON_CH2_USBEP3 | DMA_CH_VALID,
-	},
-	[DMACH_USB_EP4] = {
-		.name		= "usb-ep4",
-		.channels[3]	=S3C2410_DCON_CH3_USBEP4 | DMA_CH_VALID,
-	},
-};
-
-static void s3c2410_dma_select(struct s3c2410_dma_chan *chan,
-			       struct s3c24xx_dma_map *map)
-{
-	chan->dcon = map->channels[chan->number] & ~DMA_CH_VALID;
-}
-
-static struct s3c24xx_dma_selection __initdata s3c2410_dma_sel = {
-	.select		= s3c2410_dma_select,
-	.dcon_mask	= 7 << 24,
-	.map		= s3c2410_dma_mappings,
-	.map_size	= ARRAY_SIZE(s3c2410_dma_mappings),
-};
-
-static int s3c2410_dma_add(struct sys_device *sysdev)
-{
-	return s3c24xx_dma_init_map(&s3c2410_dma_sel);
-}
-
-#if defined(CONFIG_CPU_S3C2410)
-static struct sysdev_driver s3c2410_dma_driver = {
-	.add	= s3c2410_dma_add,
-};
-
-static int __init s3c2410_dma_init(void)
-{
-	return sysdev_driver_register(&s3c2410_sysclass, &s3c2410_dma_driver);
-}
-
-arch_initcall(s3c2410_dma_init);
-#endif
-
-#if defined(CONFIG_CPU_S3C2442)
-/* S3C2442 DMA contains the same selection table as the S3C2410 */
-static struct sysdev_driver s3c2442_dma_driver = {
-	.add	= s3c2410_dma_add,
-};
-
-static int __init s3c2442_dma_init(void)
-{
-	return sysdev_driver_register(&s3c2442_sysclass, &s3c2442_dma_driver);
-}
-
-arch_initcall(s3c2442_dma_init);
-#endif
-
diff --git a/arch/arm/mach-s3c2410/s3c2410-gpio.c b/arch/arm/mach-s3c2410/s3c2410-gpio.c
deleted file mode 100644
index ec3a276cc3c..00000000000
--- a/arch/arm/mach-s3c2410/s3c2410-gpio.c
+++ /dev/null
@@ -1,71 +0,0 @@
-/* linux/arch/arm/mach-s3c2410/s3c2410-gpio.c
- *
- * Copyright (c) 2004-2006 Simtec Electronics
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * S3C2410 GPIO support
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/interrupt.h>
-#include <linux/ioport.h>
-
-#include <asm/hardware.h>
-#include <asm/irq.h>
-#include <asm/io.h>
-
-#include <asm/arch/regs-gpio.h>
-
-int s3c2410_gpio_irqfilter(unsigned int pin, unsigned int on,
-			   unsigned int config)
-{
-	void __iomem *reg = S3C24XX_EINFLT0;
-	unsigned long flags;
-	unsigned long val;
-
-	if (pin < S3C2410_GPG8 || pin > S3C2410_GPG15)
-		return -1;
-
-	config &= 0xff;
-
-	pin -= S3C2410_GPG8;
-	reg += pin & ~3;
-
-	local_irq_save(flags);
-
-	/* update filter width and clock source */
-
-	val = __raw_readl(reg);
-	val &= ~(0xff << ((pin & 3) * 8));
-	val |= config << ((pin & 3) * 8);
-	__raw_writel(val, reg);
-
-	/* update filter enable */
-
-	val = __raw_readl(S3C24XX_EXTINT2);
-	val &= ~(1 << ((pin * 4) + 3));
-	val |= on << ((pin * 4) + 3);
-	__raw_writel(val, S3C24XX_EXTINT2);
-
-	local_irq_restore(flags);
-
-	return 0;
-}
-
-EXPORT_SYMBOL(s3c2410_gpio_irqfilter);
diff --git a/arch/arm/mach-s3c2410/s3c2410-irq.c b/arch/arm/mach-s3c2410/s3c2410-irq.c
deleted file mode 100644
index c796c9c76e7..00000000000
--- a/arch/arm/mach-s3c2410/s3c2410-irq.c
+++ /dev/null
@@ -1,48 +0,0 @@
-/* linux/arch/arm/mach-s3c2410/s3c2410-irq.c
- *
- * Copyright (c) 2006 Simtec Electronics
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- *
-*/
-
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/interrupt.h>
-#include <linux/ioport.h>
-#include <linux/ptrace.h>
-#include <linux/sysdev.h>
-
-#include "cpu.h"
-#include "pm.h"
-
-static int s3c2410_irq_add(struct sys_device *sysdev)
-{
-	return 0;
-}
-
-static struct sysdev_driver s3c2410_irq_driver = {
-	.add		= s3c2410_irq_add,
-	.suspend	= s3c24xx_irq_suspend,
-	.resume		= s3c24xx_irq_resume,
-};
-
-static int s3c2410_irq_init(void)
-{
-	return sysdev_driver_register(&s3c2410_sysclass, &s3c2410_irq_driver);
-}
-
-arch_initcall(s3c2410_irq_init);
diff --git a/arch/arm/mach-s3c2410/s3c2410-pm.c b/arch/arm/mach-s3c2410/s3c2410-pm.c
deleted file mode 100644
index 8bb6e5e21f5..00000000000
--- a/arch/arm/mach-s3c2410/s3c2410-pm.c
+++ /dev/null
@@ -1,156 +0,0 @@
-/* linux/arch/arm/mach-s3c2410/s3c2410-pm.c
- *
- * Copyright (c) 2006 Simtec Electronics
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * S3C2410 (and compatible) Power Manager (Suspend-To-RAM) support
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
-*/
-
-#include <linux/init.h>
-#include <linux/suspend.h>
-#include <linux/errno.h>
-#include <linux/time.h>
-#include <linux/sysdev.h>
-
-#include <asm/hardware.h>
-#include <asm/io.h>
-
-#include <asm/mach-types.h>
-
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/h1940.h>
-
-#include "cpu.h"
-#include "pm.h"
-
-#ifdef CONFIG_S3C2410_PM_DEBUG
-extern void pm_dbg(const char *fmt, ...);
-#define DBG(fmt...) pm_dbg(fmt)
-#else
-#define DBG(fmt...) printk(KERN_DEBUG fmt)
-#endif
-
-static void s3c2410_pm_prepare(void)
-{
-	/* ensure at least GSTATUS3 has the resume address */
-
-	__raw_writel(virt_to_phys(s3c2410_cpu_resume), S3C2410_GSTATUS3);
-
-	DBG("GSTATUS3 0x%08x\n", __raw_readl(S3C2410_GSTATUS3));
-	DBG("GSTATUS4 0x%08x\n", __raw_readl(S3C2410_GSTATUS4));
-
-	if (machine_is_h1940()) {
-		void *base = phys_to_virt(H1940_SUSPEND_CHECK);
-		unsigned long ptr;
-		unsigned long calc = 0;
-
-		/* generate check for the bootloader to check on resume */
-
-		for (ptr = 0; ptr < 0x40000; ptr += 0x400)
-			calc += __raw_readl(base+ptr);
-
-		__raw_writel(calc, phys_to_virt(H1940_SUSPEND_CHECKSUM));
-	}
-
-	/* the RX3715 uses similar code and the same H1940 and the
-	 * same offsets for resume and checksum pointers */
-
-	if (machine_is_rx3715()) {
-		void *base = phys_to_virt(H1940_SUSPEND_CHECK);
-		unsigned long ptr;
-		unsigned long calc = 0;
-
-		/* generate check for the bootloader to check on resume */
-
-		for (ptr = 0; ptr < 0x40000; ptr += 0x4)
-			calc += __raw_readl(base+ptr);
-
-		__raw_writel(calc, phys_to_virt(H1940_SUSPEND_CHECKSUM));
-	}
-
-	if ( machine_is_aml_m5900() )
-		s3c2410_gpio_setpin(S3C2410_GPF2, 1);
-
-}
-
-static int s3c2410_pm_resume(struct sys_device *dev)
-{
-	unsigned long tmp;
-
-	/* unset the return-from-sleep flag, to ensure reset */
-
-	tmp = __raw_readl(S3C2410_GSTATUS2);
-	tmp &= S3C2410_GSTATUS2_OFFRESET;
-	__raw_writel(tmp, S3C2410_GSTATUS2);
-
-	if ( machine_is_aml_m5900() )
-		s3c2410_gpio_setpin(S3C2410_GPF2, 0);
-
-	return 0;
-}
-
-static int s3c2410_pm_add(struct sys_device *dev)
-{
-	pm_cpu_prep = s3c2410_pm_prepare;
-	pm_cpu_sleep = s3c2410_cpu_suspend;
-
-	return 0;
-}
-
-#if defined(CONFIG_CPU_S3C2410)
-static struct sysdev_driver s3c2410_pm_driver = {
-	.add		= s3c2410_pm_add,
-	.resume		= s3c2410_pm_resume,
-};
-
-/* register ourselves */
-
-static int __init s3c2410_pm_drvinit(void)
-{
-	return sysdev_driver_register(&s3c2410_sysclass, &s3c2410_pm_driver);
-}
-
-arch_initcall(s3c2410_pm_drvinit);
-#endif
-
-#if defined(CONFIG_CPU_S3C2440)
-static struct sysdev_driver s3c2440_pm_driver = {
-	.add		= s3c2410_pm_add,
-	.resume		= s3c2410_pm_resume,
-};
-
-static int __init s3c2440_pm_drvinit(void)
-{
-	return sysdev_driver_register(&s3c2440_sysclass, &s3c2440_pm_driver);
-}
-
-arch_initcall(s3c2440_pm_drvinit);
-#endif
-
-#if defined(CONFIG_CPU_S3C2442)
-static struct sysdev_driver s3c2442_pm_driver = {
-	.add		= s3c2410_pm_add,
-	.resume		= s3c2410_pm_resume,
-};
-
-static int __init s3c2442_pm_drvinit(void)
-{
-	return sysdev_driver_register(&s3c2442_sysclass, &s3c2442_pm_driver);
-}
-
-arch_initcall(s3c2442_pm_drvinit);
-#endif
diff --git a/arch/arm/mach-s3c2410/s3c2410-sleep.S b/arch/arm/mach-s3c2410/s3c2410-sleep.S
deleted file mode 100644
index 9179a102458..00000000000
--- a/arch/arm/mach-s3c2410/s3c2410-sleep.S
+++ /dev/null
@@ -1,68 +0,0 @@
-/* linux/arch/arm/mach-s3c2410/s3c2410-sleep.S
- *
- * Copyright (c) 2004 Simtec Electronics
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * S3C2410 Power Manager (Suspend-To-RAM) support
- *
- * Based on PXA/SA1100 sleep code by:
- *	Nicolas Pitre, (c) 2002 Monta Vista Software Inc
- *	Cliff Brake, (c) 2001
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
-*/
-
-#include <linux/linkage.h>
-#include <asm/assembler.h>
-#include <asm/hardware.h>
-#include <asm/arch/map.h>
-
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/regs-clock.h>
-#include <asm/arch/regs-mem.h>
-#include <asm/arch/regs-serial.h>
-
-	/* s3c2410_cpu_suspend
-	 *
-	 * put the cpu into sleep mode
-	*/
-
-ENTRY(s3c2410_cpu_suspend)
-	@@ prepare cpu to sleep
-
-	ldr	r4, =S3C2410_REFRESH
-	ldr	r5, =S3C24XX_MISCCR
-	ldr	r6, =S3C2410_CLKCON
-	ldr	r7, [ r4 ]		@ get REFRESH (and ensure in TLB)
-	ldr	r8, [ r5 ]		@ get MISCCR (and ensure in TLB)
-	ldr	r9, [ r6 ]		@ get CLKCON (and ensure in TLB)
-
-	orr	r7, r7, #S3C2410_REFRESH_SELF	@ SDRAM sleep command
-	orr	r8, r8, #S3C2410_MISCCR_SDSLEEP @ SDRAM power-down signals
-	orr	r9, r9, #S3C2410_CLKCON_POWER	@ power down command
-
-	teq	pc, #0			@ first as a trial-run to load cache
-	bl	s3c2410_do_sleep
-	teq	r0, r0			@ now do it for real
-	b	s3c2410_do_sleep	@
-
-	@@ align next bit of code to cache line
-	.align	8
-s3c2410_do_sleep:
-	streq	r7, [ r4 ]			@ SDRAM sleep command
-	streq	r8, [ r5 ]			@ SDRAM power-down config
-	streq	r9, [ r6 ]			@ CPU sleep
-1:	beq	1b
-	mov	pc, r14
diff --git a/arch/arm/mach-s3c2410/s3c2410.c b/arch/arm/mach-s3c2410/s3c2410.c
index 4cdc0d70c19..1a86a980375 100644
--- a/arch/arm/mach-s3c2410/s3c2410.c
+++ b/arch/arm/mach-s3c2410/s3c2410.c
@@ -31,10 +31,10 @@
 #include <asm/arch/regs-clock.h>
 #include <asm/arch/regs-serial.h>
 
-#include "s3c2410.h"
-#include "cpu.h"
-#include "devs.h"
-#include "clock.h"
+#include <asm/plat-s3c24xx/s3c2410.h>
+#include <asm/plat-s3c24xx/cpu.h>
+#include <asm/plat-s3c24xx/devs.h>
+#include <asm/plat-s3c24xx/clock.h>
 
 /* Initial IO mappings */
 
@@ -110,7 +110,7 @@ static struct sys_device s3c2410_sysdev = {
 
 /* need to register class before we actually register the device, and
  * we also need to ensure that it has been initialised before any of the
- * drivers even try to use it (even if not on an s3c2440 based system)
+ * drivers even try to use it (even if not on an s3c2410 based system)
  * as a driver which may support both 2410 and 2440 may try and use it.
 */
 
diff --git a/arch/arm/mach-s3c2410/s3c2410.h b/arch/arm/mach-s3c2410/s3c2410.h
deleted file mode 100644
index fbed084f26d..00000000000
--- a/arch/arm/mach-s3c2410/s3c2410.h
+++ /dev/null
@@ -1,31 +0,0 @@
-/* arch/arm/mach-s3c2410/s3c2410.h
- *
- * Copyright (c) 2004 Simtec Electronics
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * Header file for s3c2410 machine directory
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
-*/
-
-#ifdef CONFIG_CPU_S3C2410
-
-extern  int s3c2410_init(void);
-
-extern void s3c2410_map_io(struct map_desc *mach_desc, int size);
-
-extern void s3c2410_init_uarts(struct s3c2410_uartcfg *cfg, int no);
-
-extern void s3c2410_init_clocks(int xtal);
-
-extern  int s3c2410_baseclk_add(void);
-
-#else
-#define s3c2410_init_clocks NULL
-#define s3c2410_init_uarts NULL
-#define s3c2410_map_io NULL
-#define s3c2410_init NULL
-#endif
diff --git a/arch/arm/mach-s3c2410/s3c2412.h b/arch/arm/mach-s3c2410/s3c2412.h
deleted file mode 100644
index c6e56032a6e..00000000000
--- a/arch/arm/mach-s3c2410/s3c2412.h
+++ /dev/null
@@ -1,29 +0,0 @@
-/* arch/arm/mach-s3c2410/s3c2412.h
- *
- * Copyright (c) 2006 Simtec Electronics
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * Header file for s3c2412 cpu support
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifdef CONFIG_CPU_S3C2412
-
-extern  int s3c2412_init(void);
-
-extern void s3c2412_map_io(struct map_desc *mach_desc, int size);
-
-extern void s3c2412_init_uarts(struct s3c2410_uartcfg *cfg, int no);
-
-extern void s3c2412_init_clocks(int xtal);
-
-extern  int s3c2412_baseclk_add(void);
-#else
-#define s3c2412_init_clocks NULL
-#define s3c2412_init_uarts NULL
-#define s3c2412_map_io NULL
-#define s3c2412_init NULL
-#endif
diff --git a/arch/arm/mach-s3c2410/s3c2440.h b/arch/arm/mach-s3c2410/s3c2440.h
deleted file mode 100644
index dcd316076c5..00000000000
--- a/arch/arm/mach-s3c2410/s3c2440.h
+++ /dev/null
@@ -1,17 +0,0 @@
-/* arch/arm/mach-s3c2410/s3c2440.h
- *
- * Copyright (c) 2004-2005 Simtec Electronics
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * Header file for s3c2440 cpu support
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifdef CONFIG_CPU_S3C2440
-extern  int s3c2440_init(void);
-#else
-#define s3c2440_init NULL
-#endif
diff --git a/arch/arm/mach-s3c2410/s3c2442.h b/arch/arm/mach-s3c2410/s3c2442.h
deleted file mode 100644
index 0ae37d24866..00000000000
--- a/arch/arm/mach-s3c2410/s3c2442.h
+++ /dev/null
@@ -1,17 +0,0 @@
-/* arch/arm/mach-s3c2410/s3c2442.h
- *
- * Copyright (c) 2006 Simtec Electronics
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * Header file for s3c2442 cpu support
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifdef CONFIG_CPU_S3C2442
-extern  int s3c2442_init(void);
-#else
-#define s3c2442_init NULL
-#endif
diff --git a/arch/arm/mach-s3c2410/sleep.S b/arch/arm/mach-s3c2410/sleep.S
index 2018c2e1dcc..637aaba6539 100644
--- a/arch/arm/mach-s3c2410/sleep.S
+++ b/arch/arm/mach-s3c2410/sleep.S
@@ -1,4 +1,4 @@
-/* linux/arch/arm/mach-s3c2410/sleep.S
+/* linux/arch/arm/mach-s3c2410/s3c2410-sleep.S
  *
  * Copyright (c) 2004 Simtec Electronics
  *	Ben Dooks <ben@simtec.co.uk>
@@ -34,126 +34,35 @@
 #include <asm/arch/regs-mem.h>
 #include <asm/arch/regs-serial.h>
 
-/* CONFIG_DEBUG_RESUME is dangerous if your bootloader does not
- * reset the UART configuration, only enable if you really need this!
-*/
-//#define CONFIG_DEBUG_RESUME
-
-	.text
-
-	/* s3c2410_cpu_save
-	 *
-	 * save enough of the CPU state to allow us to re-start
-	 * pm.c code. as we store items like the sp/lr, we will
-	 * end up returning from this function when the cpu resumes
-	 * so the return value is set to mark this.
-	 *
-	 * This arangement means we avoid having to flush the cache
-	 * from this code.
-	 *
-	 * entry:
-	 *	r0 = pointer to save block
-	 *
-	 * exit:
-	 *	r0 = 0 => we stored everything
-	 *	     1 => resumed from sleep
-	*/
-
-ENTRY(s3c2410_cpu_save)
-	stmfd	sp!, { r4 - r12, lr }
-
-	@@ store co-processor registers
-
-	mrc	p15, 0, r4, c15, c1, 0	@ CP access register
-	mrc	p15, 0, r5, c13, c0, 0	@ PID
-	mrc	p15, 0, r6, c3, c0, 0	@ Domain ID
-	mrc	p15, 0, r7, c2, c0, 0	@ translation table base address
-	mrc	p15, 0, r8, c1, c0, 0	@ control register
-
-	stmia	r0, { r4 - r13 }
-
-	mov	r0, #0
-	ldmfd	sp, { r4 - r12, pc }
-
-	@@ return to the caller, after having the MMU
-	@@ turned on, this restores the last bits from the
-	@@ stack
-resume_with_mmu:
-	mov	r0, #1
-	ldmfd	sp!, { r4 - r12, pc }
-
-	.ltorg
-
-	@@ the next bits sit in the .data segment, even though they
-	@@ happen to be code... the s3c2410_sleep_save_phys needs to be
-	@@ accessed by the resume code before it can restore the MMU.
-	@@ This means that the variable has to be close enough for the
-	@@ code to read it... since the .text segment needs to be RO,
-	@@ the data segment can be the only place to put this code.
-
-	.data
-
-	.global	s3c2410_sleep_save_phys
-s3c2410_sleep_save_phys:
-	.word	0
-
-	/* s3c2410_cpu_resume
+	/* s3c2410_cpu_suspend
 	 *
-	 * resume code entry for bootloader to call
-	 *
-	 * we must put this code here in the data segment as we have no
-	 * other way of restoring the stack pointer after sleep, and we
-	 * must not write to the code segment (code is read-only)
+	 * put the cpu into sleep mode
 	*/
 
-ENTRY(s3c2410_cpu_resume)
-	mov	r0, #PSR_I_BIT | PSR_F_BIT | SVC_MODE
-	msr	cpsr_c, r0
-
-	@@ load UART to allow us to print the two characters for
-	@@ resume debug
-
-	mov	r2, #S3C24XX_PA_UART & 0xff000000
-	orr	r2, r2, #S3C24XX_PA_UART & 0xff000
-
-#if 0
-	/* SMDK2440 LED set */
-	mov	r14, #S3C24XX_PA_GPIO
-	ldr	r12, [ r14, #0x54 ]
-	bic	r12, r12, #3<<4
-	orr	r12, r12, #1<<7
-	str	r12, [ r14, #0x54 ]
-#endif
-
-#ifdef CONFIG_DEBUG_RESUME
-	mov	r3, #'L'
-	strb	r3, [ r2, #S3C2410_UTXH ]
-1001:
-	ldrb	r14, [ r3, #S3C2410_UTRSTAT ]
-	tst	r14, #S3C2410_UTRSTAT_TXE
-	beq	1001b
-#endif /* CONFIG_DEBUG_RESUME */
-
-	mov	r1, #0
-	mcr	p15, 0, r1, c8, c7, 0		@@ invalidate I & D TLBs
-	mcr	p15, 0, r1, c7, c7, 0		@@ invalidate I & D caches
-
-	ldr	r0, s3c2410_sleep_save_phys	@ address of restore block
-	ldmia	r0, { r4 - r13 }
-
-	mcr	p15, 0, r4, c15, c1, 0		@ CP access register
-	mcr	p15, 0, r5, c13, c0, 0		@ PID
-	mcr	p15, 0, r6, c3, c0, 0		@ Domain ID
-	mcr	p15, 0, r7, c2, c0, 0		@ translation table base
-
-#ifdef CONFIG_DEBUG_RESUME
-	mov	r3, #'R'
-	strb	r3, [ r2, #S3C2410_UTXH ]
-#endif
-
-	ldr	r2, =resume_with_mmu
-	mcr	p15, 0, r8, c1, c0, 0		@ turn on MMU, etc
-	nop					@ second-to-last before mmu
-	mov	pc, r2				@ go back to virtual address
-
-	.ltorg
+ENTRY(s3c2410_cpu_suspend)
+	@@ prepare cpu to sleep
+
+	ldr	r4, =S3C2410_REFRESH
+	ldr	r5, =S3C24XX_MISCCR
+	ldr	r6, =S3C2410_CLKCON
+	ldr	r7, [ r4 ]		@ get REFRESH (and ensure in TLB)
+	ldr	r8, [ r5 ]		@ get MISCCR (and ensure in TLB)
+	ldr	r9, [ r6 ]		@ get CLKCON (and ensure in TLB)
+
+	orr	r7, r7, #S3C2410_REFRESH_SELF	@ SDRAM sleep command
+	orr	r8, r8, #S3C2410_MISCCR_SDSLEEP @ SDRAM power-down signals
+	orr	r9, r9, #S3C2410_CLKCON_POWER	@ power down command
+
+	teq	pc, #0			@ first as a trial-run to load cache
+	bl	s3c2410_do_sleep
+	teq	r0, r0			@ now do it for real
+	b	s3c2410_do_sleep	@
+
+	@@ align next bit of code to cache line
+	.align	5
+s3c2410_do_sleep:
+	streq	r7, [ r4 ]			@ SDRAM sleep command
+	streq	r8, [ r5 ]			@ SDRAM power-down config
+	streq	r9, [ r6 ]			@ CPU sleep
+1:	beq	1b
+	mov	pc, r14
diff --git a/arch/arm/mach-s3c2410/usb-simtec.c b/arch/arm/mach-s3c2410/usb-simtec.c
index 22b0e1cdd4b..bcd562ac1d3 100644
--- a/arch/arm/mach-s3c2410/usb-simtec.c
+++ b/arch/arm/mach-s3c2410/usb-simtec.c
@@ -35,7 +35,7 @@
 #include <asm/io.h>
 #include <asm/irq.h>
 
-#include "devs.h"
+#include <asm/plat-s3c24xx/devs.h>
 #include "usb-simtec.h"
 
 /* control power and monitor over-current events on various Simtec
diff --git a/arch/arm/mach-s3c2412/Kconfig b/arch/arm/mach-s3c2412/Kconfig
new file mode 100644
index 00000000000..befc5fdbb61
--- /dev/null
+++ b/arch/arm/mach-s3c2412/Kconfig
@@ -0,0 +1,58 @@
+# arch/arm/mach-s3c2412/Kconfig
+#
+# Copyright 2007 Simtec Electronics
+#
+# Licensed under GPLv2
+
+config CPU_S3C2412
+	bool
+	depends on ARCH_S3C2410
+	select S3C2412_PM if PM
+	select S3C2412_DMA if S3C2410_DMA
+	help
+	  Support for the S3C2412 and S3C2413 SoCs from the S3C24XX line
+
+config CPU_S3C2412_ONLY
+	bool
+	depends on ARCH_S3C2410 && !CPU_S3C2400 && !CPU_S3C2410 && \
+		   !CPU_S3C2440 && !CPU_S3C2442 && !CPU_S3C2443 && CPU_S3C2412
+	default y if CPU_S3C2412
+
+config S3C2412_DMA
+	bool
+	depends on CPU_S3C2412
+	help
+	  Internal config node for S3C2412 DMA support
+
+config S3C2412_PM
+	bool
+	help
+	  Internal config node to apply S3C2412 power management
+
+
+menu "S3C2412 Machines"
+
+config MACH_SMDK2413
+	bool "SMDK2413"
+	select CPU_S3C2412
+	select MACH_S3C2413
+	select MACH_SMDK
+	help
+	  Say Y here if you are using an SMDK2413
+
+config MACH_S3C2413
+	bool
+	help
+	  Internal node for S3C2413 version of SMDK2413, so that
+	  machine_is_s3c2413() will work when MACH_SMDK2413 is
+	  selected
+
+config MACH_VSTMS
+	bool "VMSTMS"
+	select CPU_S3C2412
+	help
+	  Say Y here if you are using an VSTMS board
+
+
+endmenu
+
diff --git a/arch/arm/mach-s3c2412/Makefile b/arch/arm/mach-s3c2412/Makefile
new file mode 100644
index 00000000000..f8e011691b3
--- /dev/null
+++ b/arch/arm/mach-s3c2412/Makefile
@@ -0,0 +1,21 @@
+# arch/arm/mach-s3c2412/Makefile
+#
+# Copyright 2007 Simtec Electronics
+#
+# Licensed under GPLv2
+
+obj-y				:=
+obj-m				:=
+obj-n				:=
+obj-				:=
+
+obj-$(CONFIG_CPU_S3C2412)	+= s3c2412.o
+obj-$(CONFIG_CPU_S3C2412)	+= irq.o
+obj-$(CONFIG_CPU_S3C2412)	+= clock.o
+obj-$(CONFIG_S3C2412_DMA)	+= dma.o
+obj-$(CONFIG_S3C2412_PM)	+= pm.o
+
+# Machine support
+
+obj-$(CONFIG_MACH_SMDK2413)	+= mach-smdk2413.o
+obj-$(CONFIG_MACH_VSTMS)	+= mach-vstms.o
diff --git a/arch/arm/mach-s3c2410/s3c2412-clock.c b/arch/arm/mach-s3c2412/clock.c
index 8f94ad83901..6a8e4448770 100644
--- a/arch/arm/mach-s3c2410/s3c2412-clock.c
+++ b/arch/arm/mach-s3c2412/clock.c
@@ -1,4 +1,4 @@
-/* linux/arch/arm/mach-s3c2410/s3c2412-clock.c
+/* linux/arch/arm/mach-s3c2412/clock.c
  *
  * Copyright (c) 2006 Simtec Electronics
  *	Ben Dooks <ben@simtec.co.uk>
@@ -41,9 +41,9 @@
 #include <asm/arch/regs-clock.h>
 #include <asm/arch/regs-gpio.h>
 
-#include "s3c2412.h"
-#include "clock.h"
-#include "cpu.h"
+#include <asm/plat-s3c24xx/s3c2412.h>
+#include <asm/plat-s3c24xx/clock.h>
+#include <asm/plat-s3c24xx/cpu.h>
 
 /* We currently have to assume that the system is running
  * from the XTPll input, and that all ***REFCLKs are being
diff --git a/arch/arm/mach-s3c2410/s3c2412-dma.c b/arch/arm/mach-s3c2412/dma.c
index 138f726ac6b..d0f4695c09d 100644
--- a/arch/arm/mach-s3c2410/s3c2412-dma.c
+++ b/arch/arm/mach-s3c2412/dma.c
@@ -1,4 +1,4 @@
-/* linux/arch/arm/mach-s3c2410/s3c2412-dma.c
+/* linux/arch/arm/mach-s3c2412/dma.c
  *
  * Copyright (c) 2006 Simtec Electronics
  *	Ben Dooks <ben@simtec.co.uk>
@@ -21,8 +21,8 @@
 #include <asm/arch/dma.h>
 #include <asm/io.h>
 
-#include "dma.h"
-#include "cpu.h"
+#include <asm/plat-s3c24xx/dma.h>
+#include <asm/plat-s3c24xx/cpu.h>
 
 #include <asm/arch/regs-serial.h>
 #include <asm/arch/regs-gpio.h>
@@ -146,6 +146,7 @@ static struct s3c24xx_dma_selection __initdata s3c2412_dma_sel = {
 
 static int s3c2412_dma_add(struct sys_device *sysdev)
 {
+	s3c2410_dma_init();
 	return s3c24xx_dma_init_map(&s3c2412_dma_sel);
 }
 
diff --git a/arch/arm/mach-s3c2410/s3c2412-irq.c b/arch/arm/mach-s3c2412/irq.c
index ffcc30b23a8..e89dbdcb1b7 100644
--- a/arch/arm/mach-s3c2410/s3c2412-irq.c
+++ b/arch/arm/mach-s3c2412/irq.c
@@ -1,4 +1,4 @@
-/* linux/arch/arm/mach-s3c2412/s3c2412-irq.c
+/* linux/arch/arm/mach-s3c2412/irq.c
  *
  * Copyright (c) 2006 Simtec Electronics
  *	Ben Dooks <ben@simtec.co.uk>
@@ -35,9 +35,9 @@
 #include <asm/arch/regs-irq.h>
 #include <asm/arch/regs-gpio.h>
 
-#include "cpu.h"
-#include "irq.h"
-#include "pm.h"
+#include <asm/plat-s3c24xx/cpu.h>
+#include <asm/plat-s3c24xx/irq.h>
+#include <asm/plat-s3c24xx/pm.h>
 
 /* the s3c2412 changes the behaviour of IRQ_EINT0 through IRQ_EINT3 by
  * having them turn up in both the INT* and the EINT* registers. Whilst
diff --git a/arch/arm/mach-s3c2410/mach-smdk2413.c b/arch/arm/mach-s3c2412/mach-smdk2413.c
index 4f89abd7a6d..b5befce6c8d 100644
--- a/arch/arm/mach-s3c2410/mach-smdk2413.c
+++ b/arch/arm/mach-s3c2412/mach-smdk2413.c
@@ -1,4 +1,4 @@
-/* linux/arch/arm/mach-s3c2410/mach-smdk2413.c
+/* linux/arch/arm/mach-s3c2412/mach-smdk2413.c
  *
  * Copyright (c) 2006 Simtec Electronics
  *	Ben Dooks <ben@simtec.co.uk>
@@ -37,15 +37,16 @@
 #include <asm/arch/regs-lcd.h>
 
 #include <asm/arch/idle.h>
+#include <asm/arch/udc.h>
 #include <asm/arch/fb.h>
 
-#include "s3c2410.h"
-#include "s3c2412.h"
-#include "clock.h"
-#include "devs.h"
-#include "cpu.h"
+#include <asm/plat-s3c24xx/s3c2410.h>
+#include <asm/plat-s3c24xx/s3c2412.h>
+#include <asm/plat-s3c24xx/clock.h>
+#include <asm/plat-s3c24xx/devs.h>
+#include <asm/plat-s3c24xx/cpu.h>
 
-#include "common-smdk.h"
+#include <asm/plat-s3c24xx/common-smdk.h>
 
 static struct map_desc smdk2413_iodesc[] __initdata = {
 };
@@ -75,12 +76,38 @@ static struct s3c2410_uartcfg smdk2413_uartcfgs[] __initdata = {
 	}
 };
 
+static void smdk2413_udc_pullup(enum s3c2410_udc_cmd_e cmd)
+{
+	printk(KERN_DEBUG "udc: pullup(%d)\n",cmd);
+
+	switch (cmd)
+	{
+		case S3C2410_UDC_P_ENABLE :
+			s3c2410_gpio_setpin(S3C2410_GPF2, 1);
+			break;
+		case S3C2410_UDC_P_DISABLE :
+			s3c2410_gpio_setpin(S3C2410_GPF2, 0);
+			break;
+		case S3C2410_UDC_P_RESET :
+			break;
+		default:
+			break;
+	}
+}
+
+
+static struct s3c2410_udc_mach_info smdk2413_udc_cfg __initdata = {
+	.udc_command		= smdk2413_udc_pullup,
+};
+
+
 static struct platform_device *smdk2413_devices[] __initdata = {
 	&s3c_device_usb,
 	//&s3c_device_lcd,
 	&s3c_device_wdt,
 	&s3c_device_i2c,
 	&s3c_device_iis,
+	&s3c_device_usbgadget,
 };
 
 static struct s3c24xx_board smdk2413_board __initdata = {
@@ -109,7 +136,19 @@ static void __init smdk2413_map_io(void)
 }
 
 static void __init smdk2413_machine_init(void)
-{
+{	/* Turn off suspend on both USB ports, and switch the
+	 * selectable USB port to USB device mode. */
+
+	s3c2410_gpio_setpin(S3C2410_GPF2, 0);
+	s3c2410_gpio_cfgpin(S3C2410_GPF2, S3C2410_GPIO_OUTPUT);
+
+	s3c2410_modify_misccr(S3C2410_MISCCR_USBHOST |
+			      S3C2410_MISCCR_USBSUSPND0 |
+			      S3C2410_MISCCR_USBSUSPND1, 0x0);
+
+
+ 	s3c24xx_udc_set_platdata(&smdk2413_udc_cfg);
+
 	smdk_machine_init();
 }
 
@@ -126,6 +165,19 @@ MACHINE_START(S3C2413, "S3C2413")
 	.timer		= &s3c24xx_timer,
 MACHINE_END
 
+MACHINE_START(SMDK2412, "SMDK2412")
+	/* Maintainer: Ben Dooks <ben@fluff.org> */
+	.phys_io	= S3C2410_PA_UART,
+	.io_pg_offst	= (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc,
+	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+
+	.fixup		= smdk2413_fixup,
+	.init_irq	= s3c24xx_init_irq,
+	.map_io		= smdk2413_map_io,
+	.init_machine	= smdk2413_machine_init,
+	.timer		= &s3c24xx_timer,
+MACHINE_END
+
 MACHINE_START(SMDK2413, "SMDK2413")
 	/* Maintainer: Ben Dooks <ben@fluff.org> */
 	.phys_io	= S3C2410_PA_UART,
diff --git a/arch/arm/mach-s3c2410/mach-vstms.c b/arch/arm/mach-s3c2412/mach-vstms.c
index 0360e1055bc..4231b549d79 100644
--- a/arch/arm/mach-s3c2410/mach-vstms.c
+++ b/arch/arm/mach-s3c2412/mach-vstms.c
@@ -1,4 +1,4 @@
-/* linux/arch/arm/mach-s3c2410/mach-vstms.c
+/* linux/arch/arm/mach-s3c2412/mach-vstms.c
  *
  * (C) 2006 Thomas Gleixner <tglx@linutronix.de>
  *
@@ -28,7 +28,6 @@
 #include <asm/mach/irq.h>
 
 #include <asm/hardware.h>
-#include <asm/hardware/iomd.h>
 #include <asm/setup.h>
 #include <asm/io.h>
 #include <asm/irq.h>
@@ -43,11 +42,11 @@
 
 #include <asm/arch/nand.h>
 
-#include "s3c2410.h"
-#include "s3c2412.h"
-#include "clock.h"
-#include "devs.h"
-#include "cpu.h"
+#include <asm/plat-s3c24xx/s3c2410.h>
+#include <asm/plat-s3c24xx/s3c2412.h>
+#include <asm/plat-s3c24xx/clock.h>
+#include <asm/plat-s3c24xx/devs.h>
+#include <asm/plat-s3c24xx/cpu.h>
 
 
 static struct map_desc vstms_iodesc[] __initdata = {
diff --git a/arch/arm/mach-s3c2410/s3c2412-pm.c b/arch/arm/mach-s3c2412/pm.c
index 19b63322d25..8988dac388a 100644
--- a/arch/arm/mach-s3c2410/s3c2412-pm.c
+++ b/arch/arm/mach-s3c2412/pm.c
@@ -1,4 +1,4 @@
-/* linux/arch/arm/mach-s3c2410/s3c2412-pm.c
+/* linux/arch/arm/mach-s3c2412/pm.c
  *
  * Copyright (c) 2006 Simtec Electronics
  *	Ben Dooks <ben@simtec.co.uk>
@@ -28,10 +28,10 @@
 #include <asm/arch/regs-gpio.h>
 #include <asm/arch/regs-dsc.h>
 
-#include "cpu.h"
-#include "pm.h"
+#include <asm/plat-s3c24xx/cpu.h>
+#include <asm/plat-s3c24xx/pm.h>
 
-#include "s3c2412.h"
+#include <asm/plat-s3c24xx/s3c2412.h>
 
 static void s3c2412_cpu_suspend(void)
 {
diff --git a/arch/arm/mach-s3c2410/s3c2412.c b/arch/arm/mach-s3c2412/s3c2412.c
index 2f651a811ec..aafe0bc593f 100644
--- a/arch/arm/mach-s3c2410/s3c2412.c
+++ b/arch/arm/mach-s3c2412/s3c2412.c
@@ -1,4 +1,4 @@
-/* linux/arch/arm/mach-s3c2410/s3c2412.c
+/* linux/arch/arm/mach-s3c2412/s3c2412.c
  *
  * Copyright (c) 2006 Simtec Electronics
  *	Ben Dooks <ben@simtec.co.uk>
@@ -38,11 +38,11 @@
 #include <asm/arch/regs-gpioj.h>
 #include <asm/arch/regs-dsc.h>
 
-#include "s3c2412.h"
-#include "cpu.h"
-#include "devs.h"
-#include "clock.h"
-#include "pm.h"
+#include <asm/plat-s3c24xx/s3c2412.h>
+#include <asm/plat-s3c24xx/cpu.h>
+#include <asm/plat-s3c24xx/devs.h>
+#include <asm/plat-s3c24xx/clock.h>
+#include <asm/plat-s3c24xx/pm.h>
 
 #ifndef CONFIG_CPU_S3C2412_ONLY
 void __iomem *s3c24xx_va_gpio2 = S3C24XX_VA_GPIO;
diff --git a/arch/arm/mach-s3c2440/Kconfig b/arch/arm/mach-s3c2440/Kconfig
new file mode 100644
index 00000000000..e3bfda098c0
--- /dev/null
+++ b/arch/arm/mach-s3c2440/Kconfig
@@ -0,0 +1,71 @@
+# arch/arm/mach-s3c2440/Kconfig
+#
+# Copyright 2007 Simtec Electronics
+#
+# Licensed under GPLv2
+
+config CPU_S3C2440
+	bool
+	depends on ARCH_S3C2410
+	select S3C2410_CLOCK
+	select S3C2410_PM if PM
+	select S3C2410_GPIO
+	select S3C2440_DMA if S3C2410_DMA
+	select CPU_S3C244X
+	help
+	  Support for S3C2440 Samsung Mobile CPU based systems.
+
+config S3C2440_DMA
+	bool
+	depends on ARCH_S3C2410 && CPU_S3C24405B
+	help
+	  Support for S3C2440 specific DMA code5A
+
+
+menu "S3C2440 Machines"
+
+config MACH_ANUBIS
+	bool "Simtec Electronics ANUBIS"
+	select CPU_S3C2440
+	select PM_SIMTEC if PM
+	help
+	  Say Y here if you are using the Simtec Electronics ANUBIS
+	  development system
+
+config MACH_OSIRIS
+	bool "Simtec IM2440D20 (OSIRIS) module"
+	select CPU_S3C2440
+	select PM_SIMTEC if PM
+	help
+	  Say Y here if you are using the Simtec IM2440D20 module, also
+	  known as the Osiris.
+
+config MACH_RX3715
+	bool "HP iPAQ rx3715"
+	select CPU_S3C2440
+	select PM_H1940 if PM
+	help
+	  Say Y here if you are using the HP iPAQ rx3715.
+
+config ARCH_S3C2440
+	bool "SMDK2440"
+	select CPU_S3C2440
+	select MACH_SMDK
+	help
+	  Say Y here if you are using the SMDK2440.
+
+config MACH_NEXCODER_2440
+ 	bool "NexVision NEXCODER 2440 Light Board"
+ 	select CPU_S3C2440
+	help
+ 	  Say Y here if you are using the Nex Vision NEXCODER 2440 Light Board
+
+config SMDK2440_CPU2440
+	bool "SMDK2440 with S3C2440 CPU module"
+	depends on ARCH_S3C2440
+	default y if ARCH_S3C2440
+	select CPU_S3C2440
+
+
+endmenu
+
diff --git a/arch/arm/mach-s3c2440/Makefile b/arch/arm/mach-s3c2440/Makefile
new file mode 100644
index 00000000000..c81ed6248dc
--- /dev/null
+++ b/arch/arm/mach-s3c2440/Makefile
@@ -0,0 +1,23 @@
+# arch/arm/mach-s3c2440/Makefile
+#
+# Copyright 2007 Simtec Electronics
+#
+# Licensed under GPLv2
+
+obj-y				:=
+obj-m				:=
+obj-n				:=
+obj-				:=
+
+obj-$(CONFIG_CPU_S3C2440)	+= s3c2440.o dsc.o
+obj-$(CONFIG_CPU_S3C2440)	+= irq.o
+obj-$(CONFIG_CPU_S3C2440)	+= clock.o
+obj-$(CONFIG_S3C2440_DMA)	+= dma.o
+
+# Machine support
+
+obj-$(CONFIG_MACH_ANUBIS)	+= mach-anubis.o
+obj-$(CONFIG_MACH_OSIRIS)	+= mach-osiris.o
+obj-$(CONFIG_MACH_RX3715)	+= mach-rx3715.o
+obj-$(CONFIG_ARCH_S3C2440)	+= mach-smdk2440.o
+obj-$(CONFIG_MACH_NEXCODER_2440) += mach-nexcoder.o
diff --git a/arch/arm/mach-s3c2410/s3c2440-clock.c b/arch/arm/mach-s3c2440/clock.c
index ba13c1d079d..79e2ea4adaf 100644
--- a/arch/arm/mach-s3c2410/s3c2440-clock.c
+++ b/arch/arm/mach-s3c2440/clock.c
@@ -1,4 +1,4 @@
-/* linux/arch/arm/mach-s3c2410/s3c2440-clock.c
+/* linux/arch/arm/mach-s3c2440/clock.c
  *
  * Copyright (c) 2004-2005 Simtec Electronics
  *	http://armlinux.simtec.co.uk/
@@ -41,8 +41,8 @@
 
 #include <asm/arch/regs-clock.h>
 
-#include "clock.h"
-#include "cpu.h"
+#include <asm/plat-s3c24xx/clock.h>
+#include <asm/plat-s3c24xx/cpu.h>
 
 /* S3C2440 extended clock support */
 
diff --git a/arch/arm/mach-s3c2410/s3c2440-dma.c b/arch/arm/mach-s3c2440/dma.c
index 47b861b9443..cd035a3ec87 100644
--- a/arch/arm/mach-s3c2410/s3c2440-dma.c
+++ b/arch/arm/mach-s3c2440/dma.c
@@ -1,4 +1,4 @@
-/* linux/arch/arm/mach-s3c2410/s3c2440-dma.c
+/* linux/arch/arm/mach-s3c2440/dma.c
  *
  * Copyright (c) 2006 Simtec Electronics
  *	Ben Dooks <ben@simtec.co.uk>
@@ -19,9 +19,9 @@
 
 #include <asm/dma.h>
 #include <asm/arch/dma.h>
-#include "dma.h"
 
-#include "cpu.h"
+#include <asm/plat-s3c24xx/dma.h>
+#include <asm/plat-s3c24xx/cpu.h>
 
 #include <asm/arch/regs-serial.h>
 #include <asm/arch/regs-gpio.h>
@@ -147,8 +147,53 @@ static struct s3c24xx_dma_selection __initdata s3c2440_dma_sel = {
 	.map_size	= ARRAY_SIZE(s3c2440_dma_mappings),
 };
 
+static struct s3c24xx_dma_order __initdata s3c2440_dma_order = {
+	.channels	= {
+		[DMACH_SDI]	= {
+			.list	= {
+				[0]	= 3 | DMA_CH_VALID,
+				[1]	= 2 | DMA_CH_VALID,
+				[2]	= 1 | DMA_CH_VALID,
+				[3]	= 0 | DMA_CH_VALID,
+			},
+		},
+		[DMACH_I2S_IN]	= {
+			.list	= {
+				[0]	= 1 | DMA_CH_VALID,
+				[1]	= 2 | DMA_CH_VALID,
+			},
+		},
+		[DMACH_I2S_OUT]	= {
+			.list	= {
+				[0]	= 2 | DMA_CH_VALID,
+				[1]	= 1 | DMA_CH_VALID,
+			},
+		},
+		[DMACH_PCM_IN] = {
+			.list	= {
+				[0]	= 2 | DMA_CH_VALID,
+				[1]	= 1 | DMA_CH_VALID,
+			},
+		},
+		[DMACH_PCM_OUT] = {
+			.list	= {
+				[0]	= 1 | DMA_CH_VALID,
+				[1]	= 3 | DMA_CH_VALID,
+			},
+		},
+		[DMACH_MIC_IN] = {
+			.list	= {
+				[0]	= 3 | DMA_CH_VALID,
+				[1]	= 2 | DMA_CH_VALID,
+			},
+		},
+	},
+};
+
 static int s3c2440_dma_add(struct sys_device *sysdev)
 {
+	s3c2410_dma_init();
+	s3c24xx_dma_order_set(&s3c2440_dma_order);
 	return s3c24xx_dma_init_map(&s3c2440_dma_sel);
 }
 
diff --git a/arch/arm/mach-s3c2410/s3c2440-dsc.c b/arch/arm/mach-s3c2440/dsc.c
index c92ea66ba45..2995ff5681b 100644
--- a/arch/arm/mach-s3c2410/s3c2440-dsc.c
+++ b/arch/arm/mach-s3c2440/dsc.c
@@ -1,4 +1,4 @@
-/* linux/arch/arm/mach-s3c2410/s3c2440-dsc.c
+/* linux/arch/arm/mach-s3c2440/dsc.c
  *
  * Copyright (c) 2004-2005 Simtec Electronics
  *   Ben Dooks <ben@simtec.co.uk>
@@ -27,8 +27,8 @@
 #include <asm/arch/regs-gpio.h>
 #include <asm/arch/regs-dsc.h>
 
-#include "cpu.h"
-#include "s3c2440.h"
+#include <asm/plat-s3c24xx/cpu.h>
+#include <asm/plat-s3c24xx/s3c2440.h>
 
 int s3c2440_set_dsc(unsigned int pin, unsigned int value)
 {
diff --git a/arch/arm/mach-s3c2410/s3c2440-irq.c b/arch/arm/mach-s3c2440/irq.c
index 1ba19b27ab0..1069d13d8c5 100644
--- a/arch/arm/mach-s3c2410/s3c2440-irq.c
+++ b/arch/arm/mach-s3c2440/irq.c
@@ -1,4 +1,4 @@
-/* linux/arch/arm/mach-s3c2410/s3c2440-irq.c
+/* linux/arch/arm/mach-s3c2440/irq.c
  *
  * Copyright (c) 2003,2004 Simtec Electronics
  *	Ben Dooks <ben@simtec.co.uk>
@@ -35,9 +35,9 @@
 #include <asm/arch/regs-irq.h>
 #include <asm/arch/regs-gpio.h>
 
-#include "cpu.h"
-#include "pm.h"
-#include "irq.h"
+#include <asm/plat-s3c24xx/cpu.h>
+#include <asm/plat-s3c24xx/pm.h>
+#include <asm/plat-s3c24xx/irq.h>
 
 /* WDT/AC97 */
 
diff --git a/arch/arm/mach-s3c2410/mach-anubis.c b/arch/arm/mach-s3c2440/mach-anubis.c
index 0fad0c2fe07..3f0288eb1ed 100644
--- a/arch/arm/mach-s3c2410/mach-anubis.c
+++ b/arch/arm/mach-s3c2440/mach-anubis.c
@@ -1,4 +1,4 @@
-/* linux/arch/arm/mach-s3c2410/mach-anubis.c
+/* linux/arch/arm/mach-s3c2440/mach-anubis.c
  *
  * Copyright (c) 2003-2005 Simtec Electronics
  *	http://armlinux.simtec.co.uk/
@@ -42,9 +42,9 @@
 #include <linux/mtd/nand_ecc.h>
 #include <linux/mtd/partitions.h>
 
-#include "clock.h"
-#include "devs.h"
-#include "cpu.h"
+#include <asm/plat-s3c24xx/clock.h>
+#include <asm/plat-s3c24xx/devs.h>
+#include <asm/plat-s3c24xx/cpu.h>
 
 #define COPYRIGHT ", (c) 2005 Simtec Electronics"
 
diff --git a/arch/arm/mach-s3c2410/mach-nexcoder.c b/arch/arm/mach-s3c2440/mach-nexcoder.c
index d6dfdad8c90..6d551d88330 100644
--- a/arch/arm/mach-s3c2410/mach-nexcoder.c
+++ b/arch/arm/mach-s3c2440/mach-nexcoder.c
@@ -1,4 +1,4 @@
-/* linux/arch/arm/mach-s3c2410/mach-nexcoder.c
+/* linux/arch/arm/mach-s3c2440/mach-nexcoder.c
  *
  * Copyright (c) 2004 Nex Vision
  *   Guillaume GOURAT <guillaume.gourat@nexvision.tv>
@@ -38,11 +38,11 @@
 #include <asm/arch/regs-gpio.h>
 #include <asm/arch/regs-serial.h>
 
-#include "s3c2410.h"
-#include "s3c2440.h"
-#include "clock.h"
-#include "devs.h"
-#include "cpu.h"
+#include <asm/plat-s3c24xx/s3c2410.h>
+#include <asm/plat-s3c24xx/s3c2440.h>
+#include <asm/plat-s3c24xx/clock.h>
+#include <asm/plat-s3c24xx/devs.h>
+#include <asm/plat-s3c24xx/cpu.h>
 
 static struct map_desc nexcoder_iodesc[] __initdata = {
 	/* nothing here yet */
diff --git a/arch/arm/mach-s3c2410/mach-osiris.c b/arch/arm/mach-s3c2440/mach-osiris.c
index 37b40850c9b..2ed8e51f20c 100644
--- a/arch/arm/mach-s3c2410/mach-osiris.c
+++ b/arch/arm/mach-s3c2440/mach-osiris.c
@@ -1,4 +1,4 @@
-/* linux/arch/arm/mach-s3c2410/mach-osiris.c
+/* linux/arch/arm/mach-s3c2440/mach-osiris.c
  *
  * Copyright (c) 2005 Simtec Electronics
  *	http://armlinux.simtec.co.uk/
@@ -41,9 +41,9 @@
 #include <linux/mtd/nand_ecc.h>
 #include <linux/mtd/partitions.h>
 
-#include "clock.h"
-#include "devs.h"
-#include "cpu.h"
+#include <asm/plat-s3c24xx/clock.h>
+#include <asm/plat-s3c24xx/devs.h>
+#include <asm/plat-s3c24xx/cpu.h>
 
 /* onboard perihpheral map */
 
diff --git a/arch/arm/mach-s3c2410/mach-rx3715.c b/arch/arm/mach-s3c2440/mach-rx3715.c
index ecbcdf79d73..480ccde63fb 100644
--- a/arch/arm/mach-s3c2410/mach-rx3715.c
+++ b/arch/arm/mach-s3c2440/mach-rx3715.c
@@ -1,4 +1,4 @@
-/* linux/arch/arm/mach-s3c2410/mach-rx3715.c
+/* linux/arch/arm/mach-s3c2440/mach-rx3715.c
  *
  * Copyright (c) 2003,2004 Simtec Electronics
  *	Ben Dooks <ben@simtec.co.uk>
@@ -33,7 +33,6 @@
 #include <asm/mach/irq.h>
 
 #include <asm/hardware.h>
-#include <asm/hardware/iomd.h>
 #include <asm/io.h>
 #include <asm/irq.h>
 #include <asm/mach-types.h>
@@ -46,10 +45,10 @@
 #include <asm/arch/nand.h>
 #include <asm/arch/fb.h>
 
-#include "clock.h"
-#include "devs.h"
-#include "cpu.h"
-#include "pm.h"
+#include <asm/plat-s3c24xx/clock.h>
+#include <asm/plat-s3c24xx/devs.h>
+#include <asm/plat-s3c24xx/cpu.h>
+#include <asm/plat-s3c24xx/pm.h>
 
 static struct map_desc rx3715_iodesc[] __initdata = {
 	/* dump ISA space somewhere unused */
diff --git a/arch/arm/mach-s3c2410/mach-smdk2440.c b/arch/arm/mach-s3c2440/mach-smdk2440.c
index 2b61f4ed1da..c17eb5b1f6b 100644
--- a/arch/arm/mach-s3c2410/mach-smdk2440.c
+++ b/arch/arm/mach-s3c2440/mach-smdk2440.c
@@ -1,4 +1,4 @@
-/* linux/arch/arm/mach-s3c2410/mach-smdk2440.c
+/* linux/arch/arm/mach-s3c2440/mach-smdk2440.c
  *
  * Copyright (c) 2004,2005 Simtec Electronics
  *	Ben Dooks <ben@simtec.co.uk>
@@ -27,12 +27,10 @@
 #include <asm/mach/irq.h>
 
 #include <asm/hardware.h>
-#include <asm/hardware/iomd.h>
 #include <asm/io.h>
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-//#include <asm/debug-ll.h>
 #include <asm/arch/regs-serial.h>
 #include <asm/arch/regs-gpio.h>
 #include <asm/arch/regs-lcd.h>
@@ -40,13 +38,13 @@
 #include <asm/arch/idle.h>
 #include <asm/arch/fb.h>
 
-#include "s3c2410.h"
-#include "s3c2440.h"
-#include "clock.h"
-#include "devs.h"
-#include "cpu.h"
+#include <asm/plat-s3c24xx/s3c2410.h>
+#include <asm/plat-s3c24xx/s3c2440.h>
+#include <asm/plat-s3c24xx/clock.h>
+#include <asm/plat-s3c24xx/devs.h>
+#include <asm/plat-s3c24xx/cpu.h>
 
-#include "common-smdk.h"
+#include <asm/plat-s3c24xx/common-smdk.h>
 
 static struct map_desc smdk2440_iodesc[] __initdata = {
 	/* ISA IO Space map (memory space selected by A24) */
@@ -144,6 +142,7 @@ static struct s3c2410fb_mach_info smdk2440_lcd_cfg __initdata = {
 #endif
 
 	.lpcsel		= ((0xCE6) & ~7) | 1<<4,
+	.type		= S3C2410_LCDCON1_TFT16BPP,
 
 	.width		= 240,
 	.height		= 320,
diff --git a/arch/arm/mach-s3c2410/s3c2440.c b/arch/arm/mach-s3c2440/s3c2440.c
index 344eb27cca4..90e1da61fbc 100644
--- a/arch/arm/mach-s3c2410/s3c2440.c
+++ b/arch/arm/mach-s3c2440/s3c2440.c
@@ -1,4 +1,4 @@
-/* linux/arch/arm/mach-s3c2410/s3c2440.c
+/* linux/arch/arm/mach-s3c2440/s3c2440.c
  *
  * Copyright (c) 2004-2006 Simtec Electronics
  *   Ben Dooks <ben@simtec.co.uk>
@@ -29,9 +29,9 @@
 #include <asm/io.h>
 #include <asm/irq.h>
 
-#include "s3c2440.h"
-#include "devs.h"
-#include "cpu.h"
+#include <asm/plat-s3c24xx/s3c2440.h>
+#include <asm/plat-s3c24xx/devs.h>
+#include <asm/plat-s3c24xx/cpu.h>
 
 static struct sys_device s3c2440_sysdev = {
 	.cls		= &s3c2440_sysclass,
diff --git a/arch/arm/mach-s3c2442/Kconfig b/arch/arm/mach-s3c2442/Kconfig
new file mode 100644
index 00000000000..bf8d87abfab
--- /dev/null
+++ b/arch/arm/mach-s3c2442/Kconfig
@@ -0,0 +1,27 @@
+# arch/arm/mach-s3c2442/Kconfig
+#
+# Copyright 2007 Simtec Electronics
+#
+# Licensed under GPLv2
+
+config CPU_S3C2442
+	bool
+	depends on ARCH_S3C2420
+	select S3C2410_CLOCK
+	select S3C2410_GPIO
+	select S3C2410_PM if PM
+	select CPU_S3C244X
+	help
+	  Support for S3C2442 Samsung Mobile CPU based systems.
+
+
+menu "S3C2442 Machines"
+
+config SMDK2440_CPU2442
+	bool "SMDM2440 with S3C2442 CPU module"
+	depends on ARCH_S3C2440
+	select CPU_S3C2442
+
+
+endmenu
+
diff --git a/arch/arm/mach-s3c2442/Makefile b/arch/arm/mach-s3c2442/Makefile
new file mode 100644
index 00000000000..2a909c6c579
--- /dev/null
+++ b/arch/arm/mach-s3c2442/Makefile
@@ -0,0 +1,16 @@
+# arch/arm/mach-s3c2442/Makefile
+#
+# Copyright 2007 Simtec Electronics
+#
+# Licensed under GPLv2
+
+obj-y				:=
+obj-m				:=
+obj-n				:=
+obj-				:=
+
+obj-$(CONFIG_CPU_S3C2442)	+= s3c2442.o
+obj-$(CONFIG_CPU_S3C2442)	+= clock.o
+
+# Machine support
+
diff --git a/arch/arm/mach-s3c2410/s3c2442-clock.c b/arch/arm/mach-s3c2442/clock.c
index 4e292ca7c9b..5b9e830ac4d 100644
--- a/arch/arm/mach-s3c2410/s3c2442-clock.c
+++ b/arch/arm/mach-s3c2442/clock.c
@@ -1,4 +1,4 @@
-/* linux/arch/arm/mach-s3c2410/s3c2442-clock.c
+/* linux/arch/arm/mach-s3c2442/clock.c
  *
  * Copyright (c) 2004-2005 Simtec Electronics
  *	http://armlinux.simtec.co.uk/
@@ -41,8 +41,8 @@
 
 #include <asm/arch/regs-clock.h>
 
-#include "clock.h"
-#include "cpu.h"
+#include <asm/plat-s3c24xx/clock.h>
+#include <asm/plat-s3c24xx/cpu.h>
 
 /* S3C2442 extended clock support */
 
diff --git a/arch/arm/mach-s3c2410/s3c2442.c b/arch/arm/mach-s3c2442/s3c2442.c
index 428732ee68c..fbf8264249d 100644
--- a/arch/arm/mach-s3c2410/s3c2442.c
+++ b/arch/arm/mach-s3c2442/s3c2442.c
@@ -1,4 +1,4 @@
-/* linux/arch/arm/mach-s3c2410/s3c2442.c
+/* linux/arch/arm/mach-s3c2442/s3c2442.c
  *
  * Copyright (c) 2006 Simtec Electronics
  *   Ben Dooks <ben@simtec.co.uk>
@@ -19,8 +19,8 @@
 #include <linux/serial_core.h>
 #include <linux/sysdev.h>
 
-#include "s3c2442.h"
-#include "cpu.h"
+#include <asm/plat-s3c24xx/s3c2442.h>
+#include <asm/plat-s3c24xx/cpu.h>
 
 static struct sys_device s3c2442_sysdev = {
 	.cls		= &s3c2442_sysclass,
diff --git a/arch/arm/mach-s3c2443/Kconfig b/arch/arm/mach-s3c2443/Kconfig
new file mode 100644
index 00000000000..c649bb2e7ce
--- /dev/null
+++ b/arch/arm/mach-s3c2443/Kconfig
@@ -0,0 +1,29 @@
+# arch/arm/mach-s3c2443/Kconfig
+#
+# Copyright 2007 Simtec Electronics
+#
+# Licensed under GPLv2
+
+config CPU_S3C2443
+	bool
+	depends on ARCH_S3C2410
+	select S3C2443_DMA if S3C2410_DMA
+	help
+	  Support for the S3C2443 SoC from the S3C24XX line
+
+config S3C2443_DMA
+	bool
+	depends on CPU_S3C2443
+	help
+	  Internal config node for S3C2443 DMA support
+
+menu "S3C2443 Machines"
+
+config MACH_SMDK2443
+	bool "SMDK2443"
+	select CPU_S3C2443
+	select MACH_SMDK
+	help
+	  Say Y here if you are using an SMDK2443
+
+endmenu
diff --git a/arch/arm/mach-s3c2443/Makefile b/arch/arm/mach-s3c2443/Makefile
new file mode 100644
index 00000000000..d1843c9eb8b
--- /dev/null
+++ b/arch/arm/mach-s3c2443/Makefile
@@ -0,0 +1,20 @@
+# arch/arm/mach-s3c2443/Makefile
+#
+# Copyright 2007 Simtec Electronics
+#
+# Licensed under GPLv2
+
+obj-y				:=
+obj-m				:=
+obj-n				:=
+obj-				:=
+
+obj-$(CONFIG_CPU_S3C2443)	+= s3c2443.o
+obj-$(CONFIG_CPU_S3C2443)	+= irq.o
+obj-$(CONFIG_CPU_S3C2443)	+= clock.o
+
+obj-$(CONFIG_S3C2443_DMA)	+= dma.o
+
+# Machine support
+
+obj-$(CONFIG_MACH_SMDK2443)	+= mach-smdk2443.o
diff --git a/arch/arm/mach-s3c2443/clock.c b/arch/arm/mach-s3c2443/clock.c
new file mode 100644
index 00000000000..dd2272fb113
--- /dev/null
+++ b/arch/arm/mach-s3c2443/clock.c
@@ -0,0 +1,1007 @@
+/* linux/arch/arm/mach-s3c2443/clock.c
+ *
+ * Copyright (c) 2007 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C2443 Clock control support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+*/
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/list.h>
+#include <linux/errno.h>
+#include <linux/err.h>
+#include <linux/sysdev.h>
+#include <linux/clk.h>
+#include <linux/mutex.h>
+#include <linux/delay.h>
+#include <linux/serial_core.h>
+
+#include <asm/mach/map.h>
+
+#include <asm/hardware.h>
+#include <asm/io.h>
+
+#include <asm/arch/regs-s3c2443-clock.h>
+
+#include <asm/plat-s3c24xx/s3c2443.h>
+#include <asm/plat-s3c24xx/clock.h>
+#include <asm/plat-s3c24xx/cpu.h>
+
+/* We currently have to assume that the system is running
+ * from the XTPll input, and that all ***REFCLKs are being
+ * fed from it, as we cannot read the state of OM[4] from
+ * software.
+ *
+ * It would be possible for each board initialisation to
+ * set the correct muxing at initialisation
+*/
+
+static int s3c2443_clkcon_enable_h(struct clk *clk, int enable)
+{
+	unsigned int clocks = clk->ctrlbit;
+	unsigned long clkcon;
+
+	clkcon = __raw_readl(S3C2443_HCLKCON);
+
+	if (enable)
+		clkcon |= clocks;
+	else
+		clkcon &= ~clocks;
+
+	__raw_writel(clkcon, S3C2443_HCLKCON);
+
+	return 0;
+}
+
+static int s3c2443_clkcon_enable_p(struct clk *clk, int enable)
+{
+	unsigned int clocks = clk->ctrlbit;
+	unsigned long clkcon;
+
+	clkcon = __raw_readl(S3C2443_PCLKCON);
+
+	if (enable)
+		clkcon |= clocks;
+	else
+		clkcon &= ~clocks;
+
+	__raw_writel(clkcon, S3C2443_HCLKCON);
+
+	return 0;
+}
+
+static int s3c2443_clkcon_enable_s(struct clk *clk, int enable)
+{
+	unsigned int clocks = clk->ctrlbit;
+	unsigned long clkcon;
+
+	clkcon = __raw_readl(S3C2443_SCLKCON);
+
+	if (enable)
+		clkcon |= clocks;
+	else
+		clkcon &= ~clocks;
+
+	__raw_writel(clkcon, S3C2443_SCLKCON);
+
+	return 0;
+}
+
+static unsigned long s3c2443_roundrate_clksrc(struct clk *clk,
+					      unsigned long rate,
+					      unsigned int max)
+{
+	unsigned long parent_rate = clk_get_rate(clk->parent);
+	int div;
+
+	if (rate > parent_rate)
+		return parent_rate;
+
+	/* note, we remove the +/- 1 calculations as they cancel out */
+
+	div = (rate / parent_rate);
+
+	if (div < 1)
+		div = 1;
+	else if (div > max)
+		div = max;
+
+	return parent_rate / div;
+}
+
+static unsigned long s3c2443_roundrate_clksrc4(struct clk *clk,
+					       unsigned long rate)
+{
+	return s3c2443_roundrate_clksrc(clk, rate, 4);
+}
+
+static unsigned long s3c2443_roundrate_clksrc16(struct clk *clk,
+						unsigned long rate)
+{
+	return s3c2443_roundrate_clksrc(clk, rate, 16);
+}
+
+static unsigned long s3c2443_roundrate_clksrc256(struct clk *clk,
+						 unsigned long rate)
+{
+	return s3c2443_roundrate_clksrc(clk, rate, 256);
+}
+
+/* clock selections */
+
+/* CPU EXTCLK input */
+static struct clk clk_ext = {
+	.name		= "ext",
+	.id		= -1,
+};
+
+static struct clk clk_mpllref = {
+	.name		= "mpllref",
+	.parent		= &clk_xtal,
+	.id		= -1,
+};
+
+#if 0
+static struct clk clk_mpll = {
+	.name		= "mpll",
+	.parent		= &clk_mpllref,
+	.id		= -1,
+};
+#endif
+
+static struct clk clk_epllref;
+
+static struct clk clk_epll = {
+	.name		= "epll",
+	.parent		= &clk_epllref,
+	.id		= -1,
+};
+
+static struct clk clk_i2s_ext = {
+	.name		= "i2s-ext",
+	.id		= -1,
+};
+
+static int s3c2443_setparent_epllref(struct clk *clk, struct clk *parent)
+{
+	unsigned long clksrc = __raw_readl(S3C2443_CLKSRC);
+
+	clksrc &= ~S3C2443_CLKSRC_EPLLREF_MASK;
+
+	if (parent == &clk_xtal)
+		clksrc |= S3C2443_CLKSRC_EPLLREF_XTAL;
+	else if (parent == &clk_ext)
+		clksrc |= S3C2443_CLKSRC_EPLLREF_EXTCLK;
+	else if (parent != &clk_mpllref)
+		return -EINVAL;
+
+	__raw_writel(clksrc, S3C2443_CLKSRC);
+	clk->parent = parent;
+
+	return 0;
+}
+
+static struct clk clk_epllref = {
+	.name		= "epllref",
+	.id		= -1,
+	.set_parent	= s3c2443_setparent_epllref,
+};
+
+static unsigned long s3c2443_getrate_mdivclk(struct clk *clk)
+{
+	unsigned long parent_rate = clk_get_rate(clk->parent);
+	unsigned long div = __raw_readl(S3C2443_CLKDIV0);
+
+	div  &= S3C2443_CLKDIV0_EXTDIV_MASK;
+	div >>= (S3C2443_CLKDIV0_EXTDIV_SHIFT-1);	/* x2 */
+
+	return parent_rate / (div + 1);
+}
+
+static struct clk clk_mdivclk = {
+	.name		= "mdivclk",
+	.parent		= &clk_mpllref,
+	.id		= -1,
+	.get_rate	= s3c2443_getrate_mdivclk,
+};
+
+
+static int s3c2443_setparent_msysclk(struct clk *clk, struct clk *parent)
+{
+	unsigned long clksrc = __raw_readl(S3C2443_CLKSRC);
+
+	clksrc &= ~(S3C2443_CLKSRC_MSYSCLK_MPLL |
+		    S3C2443_CLKSRC_EXTCLK_DIV);
+
+	if (parent == &clk_mpll)
+		clksrc |= S3C2443_CLKSRC_MSYSCLK_MPLL;
+	else if (parent == &clk_mdivclk)
+		clksrc |= S3C2443_CLKSRC_EXTCLK_DIV;
+	else if (parent != &clk_mpllref)
+		return -EINVAL;
+
+	__raw_writel(clksrc, S3C2443_CLKSRC);
+	clk->parent = parent;
+
+	return 0;
+}
+
+static struct clk clk_msysclk = {
+	.name		= "msysclk",
+	.parent		= &clk_xtal,
+	.id		= -1,
+	.set_parent	= s3c2443_setparent_msysclk,
+};
+
+
+/* esysclk
+ *
+ * this is sourced from either the EPLL or the EPLLref clock
+*/
+
+static int s3c2443_setparent_esysclk(struct clk *clk, struct clk *parent)
+{
+	unsigned long clksrc = __raw_readl(S3C2443_CLKSRC);
+
+	if (parent == &clk_epll)
+		clksrc |= S3C2443_CLKSRC_ESYSCLK_EPLL;
+	else if (parent == &clk_epllref)
+		clksrc &= ~S3C2443_CLKSRC_ESYSCLK_EPLL;
+	else
+		return -EINVAL;
+
+	__raw_writel(clksrc, S3C2443_CLKSRC);
+	clk->parent = parent;
+
+	return 0;
+}
+
+static struct clk clk_esysclk = {
+	.name		= "esysclk",
+	.parent		= &clk_epll,
+	.id		= -1,
+	.set_parent	= s3c2443_setparent_esysclk,
+};
+
+/* uartclk
+ *
+ * UART baud-rate clock sourced from esysclk via a divisor
+*/
+
+static unsigned long s3c2443_getrate_uart(struct clk *clk)
+{
+	unsigned long parent_rate = clk_get_rate(clk->parent);
+	unsigned long div = __raw_readl(S3C2443_CLKDIV1);
+
+	div &= S3C2443_CLKDIV1_UARTDIV_MASK;
+	div >>= S3C2443_CLKDIV1_UARTDIV_SHIFT;
+
+	return parent_rate / (div + 1);
+}
+
+
+static int s3c2443_setrate_uart(struct clk *clk, unsigned long rate)
+{
+	unsigned long parent_rate = clk_get_rate(clk->parent);
+	unsigned long clkdivn = __raw_readl(S3C2443_CLKDIV1);
+
+	rate = s3c2443_roundrate_clksrc16(clk, rate);
+	rate = parent_rate / rate;
+
+	clkdivn &= ~S3C2443_CLKDIV1_UARTDIV_MASK;
+	clkdivn |= (rate - 1) << S3C2443_CLKDIV1_UARTDIV_SHIFT;
+
+	__raw_writel(clkdivn, S3C2443_CLKDIV1);
+	return 0;
+}
+
+static struct clk clk_uart = {
+	.name		= "uartclk",
+	.id		= -1,
+	.parent		= &clk_esysclk,
+	.get_rate	= s3c2443_getrate_uart,
+	.set_rate	= s3c2443_setrate_uart,
+	.round_rate	= s3c2443_roundrate_clksrc16,
+};
+
+/* hsspi
+ *
+ * high-speed spi clock, sourced from esysclk
+*/
+
+static unsigned long s3c2443_getrate_hsspi(struct clk *clk)
+{
+	unsigned long parent_rate = clk_get_rate(clk->parent);
+	unsigned long div = __raw_readl(S3C2443_CLKDIV1);
+
+	div &= S3C2443_CLKDIV1_HSSPIDIV_MASK;
+	div >>= S3C2443_CLKDIV1_HSSPIDIV_SHIFT;
+
+	return parent_rate / (div + 1);
+}
+
+
+static int s3c2443_setrate_hsspi(struct clk *clk, unsigned long rate)
+{
+	unsigned long parent_rate = clk_get_rate(clk->parent);
+	unsigned long clkdivn = __raw_readl(S3C2443_CLKDIV1);
+
+	rate = s3c2443_roundrate_clksrc4(clk, rate);
+	rate = parent_rate / rate;
+
+	clkdivn &= ~S3C2443_CLKDIV1_HSSPIDIV_MASK;
+	clkdivn |= (rate - 1) << S3C2443_CLKDIV1_HSSPIDIV_SHIFT;
+
+	__raw_writel(clkdivn, S3C2443_CLKDIV1);
+	return 0;
+}
+
+static struct clk clk_hsspi = {
+	.name		= "hsspi",
+	.id		= -1,
+	.parent		= &clk_esysclk,
+	.ctrlbit	= S3C2443_SCLKCON_HSSPICLK,
+	.enable		= s3c2443_clkcon_enable_s,
+	.get_rate	= s3c2443_getrate_hsspi,
+	.set_rate	= s3c2443_setrate_hsspi,
+	.round_rate	= s3c2443_roundrate_clksrc4,
+};
+
+/* usbhost
+ *
+ * usb host bus-clock, usually 48MHz to provide USB bus clock timing
+*/
+
+static unsigned long s3c2443_getrate_usbhost(struct clk *clk)
+{
+	unsigned long parent_rate = clk_get_rate(clk->parent);
+	unsigned long div = __raw_readl(S3C2443_CLKDIV1);
+
+	div &= S3C2443_CLKDIV1_USBHOSTDIV_MASK;
+	div >>= S3C2443_CLKDIV1_USBHOSTDIV_SHIFT;
+
+	return parent_rate / (div + 1);
+}
+
+static int s3c2443_setrate_usbhost(struct clk *clk, unsigned long rate)
+{
+	unsigned long parent_rate = clk_get_rate(clk->parent);
+	unsigned long clkdivn = __raw_readl(S3C2443_CLKDIV1);
+
+	rate = s3c2443_roundrate_clksrc4(clk, rate);
+	rate = parent_rate / rate;
+
+	clkdivn &= ~S3C2443_CLKDIV1_USBHOSTDIV_MASK;
+	clkdivn |= (rate - 1) << S3C2443_CLKDIV1_USBHOSTDIV_SHIFT;
+
+	__raw_writel(clkdivn, S3C2443_CLKDIV1);
+	return 0;
+}
+
+struct clk clk_usb_bus_host = {
+	.name		= "usb-bus-host-parent",
+	.id		= -1,
+	.parent		= &clk_esysclk,
+	.ctrlbit	= S3C2443_SCLKCON_USBHOST,
+	.enable		= s3c2443_clkcon_enable_s,
+	.get_rate	= s3c2443_getrate_usbhost,
+	.set_rate	= s3c2443_setrate_usbhost,
+	.round_rate	= s3c2443_roundrate_clksrc4,
+};
+
+/* clk_hsmcc_div
+ *
+ * this clock is sourced from epll, and is fed through a divider,
+ * to a mux controlled by sclkcon where either it or a extclk can
+ * be fed to the hsmmc block
+*/
+
+static unsigned long s3c2443_getrate_hsmmc_div(struct clk *clk)
+{
+	unsigned long parent_rate = clk_get_rate(clk->parent);
+	unsigned long div = __raw_readl(S3C2443_CLKDIV1);
+
+	div &= S3C2443_CLKDIV1_HSMMCDIV_MASK;
+	div >>= S3C2443_CLKDIV1_HSMMCDIV_SHIFT;
+
+	return parent_rate / (div + 1);
+}
+
+static int s3c2443_setrate_hsmmc_div(struct clk *clk, unsigned long rate)
+{
+	unsigned long parent_rate = clk_get_rate(clk->parent);
+	unsigned long clkdivn = __raw_readl(S3C2443_CLKDIV1);
+
+	rate = s3c2443_roundrate_clksrc4(clk, rate);
+	rate = parent_rate / rate;
+
+	clkdivn &= ~S3C2443_CLKDIV1_HSMMCDIV_MASK;
+	clkdivn |= (rate - 1) << S3C2443_CLKDIV1_HSMMCDIV_SHIFT;
+
+	__raw_writel(clkdivn, S3C2443_CLKDIV1);
+	return 0;
+}
+
+static struct clk clk_hsmmc_div = {
+	.name		= "hsmmc-div",
+	.id		= -1,
+	.parent		= &clk_esysclk,
+	.get_rate	= s3c2443_getrate_hsmmc_div,
+	.set_rate	= s3c2443_setrate_hsmmc_div,
+	.round_rate	= s3c2443_roundrate_clksrc4,
+};
+
+static int s3c2443_setparent_hsmmc(struct clk *clk, struct clk *parent)
+{
+	unsigned long clksrc = __raw_readl(S3C2443_SCLKCON);
+
+	clksrc &= ~(S3C2443_SCLKCON_HSMMCCLK_EXT |
+		    S3C2443_SCLKCON_HSMMCCLK_EPLL);
+
+	if (parent == &clk_epll)
+		clksrc |= S3C2443_SCLKCON_HSMMCCLK_EPLL;
+	else if (parent == &clk_ext)
+		clksrc |= S3C2443_SCLKCON_HSMMCCLK_EXT;
+	else
+		return -EINVAL;
+
+	if (clk->usage > 0) {
+		__raw_writel(clksrc, S3C2443_SCLKCON);
+	}
+
+	clk->parent = parent;
+	return 0;
+}
+
+static int s3c2443_enable_hsmmc(struct clk *clk, int enable)
+{
+	return s3c2443_setparent_hsmmc(clk, clk->parent);
+}
+
+static struct clk clk_hsmmc = {
+	.name		= "hsmmc-if",
+	.id		= -1,
+	.parent		= &clk_hsmmc_div,
+	.enable		= s3c2443_enable_hsmmc,
+	.set_parent	= s3c2443_setparent_hsmmc,
+};
+
+/* i2s_eplldiv
+ *
+ * this clock is the output from the i2s divisor of esysclk
+*/
+
+static unsigned long s3c2443_getrate_i2s_eplldiv(struct clk *clk)
+{
+	unsigned long parent_rate = clk_get_rate(clk->parent);
+	unsigned long div = __raw_readl(S3C2443_CLKDIV1);
+
+	div &= S3C2443_CLKDIV1_I2SDIV_MASK;
+	div >>= S3C2443_CLKDIV1_I2SDIV_SHIFT;
+
+	return parent_rate / (div + 1);
+}
+
+static int s3c2443_setrate_i2s_eplldiv(struct clk *clk, unsigned long rate)
+{
+	unsigned long parent_rate = clk_get_rate(clk->parent);
+	unsigned long clkdivn = __raw_readl(S3C2443_CLKDIV1);
+
+	rate = s3c2443_roundrate_clksrc16(clk, rate);
+	rate = parent_rate / rate;
+
+	clkdivn &= ~S3C2443_CLKDIV1_I2SDIV_MASK;
+	clkdivn |= (rate - 1) << S3C2443_CLKDIV1_I2SDIV_SHIFT;
+
+	__raw_writel(clkdivn, S3C2443_CLKDIV1);
+	return 0;
+}
+
+static struct clk clk_i2s_eplldiv = {
+	.name		= "i2s-eplldiv",
+	.id		= -1,
+	.parent		= &clk_esysclk,
+	.get_rate	= s3c2443_getrate_i2s_eplldiv,
+	.set_rate	= s3c2443_setrate_i2s_eplldiv,
+	.round_rate	= s3c2443_roundrate_clksrc16,
+};
+
+/* i2s-ref
+ *
+ * i2s bus reference clock, selectable from external, esysclk or epllref
+*/
+
+static int s3c2443_setparent_i2s(struct clk *clk, struct clk *parent)
+{
+	unsigned long clksrc = __raw_readl(S3C2443_CLKSRC);
+
+	clksrc &= ~S3C2443_CLKSRC_I2S_MASK;
+
+	if (parent == &clk_epllref)
+		clksrc |= S3C2443_CLKSRC_I2S_EPLLREF;
+	else if (parent == &clk_i2s_ext)
+		clksrc |= S3C2443_CLKSRC_I2S_EXT;
+	else if (parent != &clk_i2s_eplldiv)
+		return -EINVAL;
+
+	clk->parent = parent;
+	__raw_writel(clksrc, S3C2443_CLKSRC);
+
+	return 0;
+}
+
+static struct clk clk_i2s = {
+	.name		= "i2s-if",
+	.id		= -1,
+	.parent		= &clk_i2s_eplldiv,
+	.ctrlbit	= S3C2443_SCLKCON_I2SCLK,
+	.enable		= s3c2443_clkcon_enable_s,
+	.set_parent	= s3c2443_setparent_i2s,
+};
+
+/* cam-if
+ *
+ * camera interface bus-clock, divided down from esysclk
+*/
+
+static unsigned long s3c2443_getrate_cam(struct clk *clk)
+{
+	unsigned long parent_rate = clk_get_rate(clk->parent);
+	unsigned long div = __raw_readl(S3C2443_CLKDIV1);
+
+	div  &= S3C2443_CLKDIV1_CAMDIV_MASK;
+	div >>= S3C2443_CLKDIV1_CAMDIV_SHIFT;
+
+	return parent_rate / (div + 1);
+}
+
+static int s3c2443_setrate_cam(struct clk *clk, unsigned long rate)
+{
+	unsigned long parent_rate = clk_get_rate(clk->parent);
+	unsigned long clkdiv1 = __raw_readl(S3C2443_CLKDIV1);
+
+	rate = s3c2443_roundrate_clksrc16(clk, rate);
+	rate = parent_rate / rate;
+
+	clkdiv1 &= ~S3C2443_CLKDIV1_CAMDIV_MASK;
+	clkdiv1 |= (rate - 1) << S3C2443_CLKDIV1_CAMDIV_SHIFT;
+
+	__raw_writel(clkdiv1, S3C2443_CLKDIV1);
+	return 0;
+}
+
+static struct clk clk_cam = {
+	.name		= "camif-upll",		/* same as 2440 name */
+	.id		= -1,
+	.parent		= &clk_esysclk,
+	.ctrlbit	= S3C2443_SCLKCON_CAMCLK,
+	.enable		= s3c2443_clkcon_enable_s,
+	.get_rate	= s3c2443_getrate_cam,
+	.set_rate	= s3c2443_setrate_cam,
+	.round_rate	= s3c2443_roundrate_clksrc16,
+};
+
+/* display-if
+ *
+ * display interface clock, divided from esysclk
+*/
+
+static unsigned long s3c2443_getrate_display(struct clk *clk)
+{
+	unsigned long parent_rate = clk_get_rate(clk->parent);
+	unsigned long div = __raw_readl(S3C2443_CLKDIV1);
+
+	div &= S3C2443_CLKDIV1_DISPDIV_MASK;
+	div >>= S3C2443_CLKDIV1_DISPDIV_SHIFT;
+
+	return parent_rate / (div + 1);
+}
+
+static int s3c2443_setrate_display(struct clk *clk, unsigned long rate)
+{
+	unsigned long parent_rate = clk_get_rate(clk->parent);
+	unsigned long clkdivn = __raw_readl(S3C2443_CLKDIV1);
+
+	rate = s3c2443_roundrate_clksrc256(clk, rate);
+	rate = parent_rate / rate;
+
+	clkdivn &= ~S3C2443_CLKDIV1_UARTDIV_MASK;
+	clkdivn |= (rate - 1) << S3C2443_CLKDIV1_UARTDIV_SHIFT;
+
+	__raw_writel(clkdivn, S3C2443_CLKDIV1);
+	return 0;
+}
+
+static struct clk clk_display = {
+	.name		= "display-if",
+	.id		= -1,
+	.parent		= &clk_esysclk,
+	.ctrlbit	= S3C2443_SCLKCON_DISPCLK,
+	.enable		= s3c2443_clkcon_enable_s,
+	.get_rate	= s3c2443_getrate_display,
+	.set_rate	= s3c2443_setrate_display,
+	.round_rate	= s3c2443_roundrate_clksrc256,
+};
+
+/* standard clock definitions */
+
+static struct clk init_clocks_disable[] = {
+	{
+		.name		= "nand",
+		.id		= -1,
+		.parent		= &clk_h,
+	}, {
+		.name		= "sdi",
+		.id		= -1,
+		.parent		= &clk_p,
+		.enable		= s3c2443_clkcon_enable_p,
+		.ctrlbit	= S3C2443_PCLKCON_SDI,
+	}, {
+		.name		= "adc",
+		.id		= -1,
+		.parent		= &clk_p,
+		.enable		= s3c2443_clkcon_enable_p,
+		.ctrlbit	= S3C2443_PCLKCON_ADC,
+	}, {
+		.name		= "i2c",
+		.id		= -1,
+		.parent		= &clk_p,
+		.enable		= s3c2443_clkcon_enable_p,
+		.ctrlbit	= S3C2443_PCLKCON_IIC,
+	}, {
+		.name		= "iis",
+		.id		= -1,
+		.parent		= &clk_p,
+		.enable		= s3c2443_clkcon_enable_p,
+		.ctrlbit	= S3C2443_PCLKCON_IIS,
+	}, {
+		.name		= "spi",
+		.id		= 0,
+		.parent		= &clk_p,
+		.enable		= s3c2443_clkcon_enable_p,
+		.ctrlbit	= S3C2443_PCLKCON_SPI0,
+	}, {
+		.name		= "spi",
+		.id		= 1,
+		.parent		= &clk_p,
+		.enable		= s3c2443_clkcon_enable_p,
+		.ctrlbit	= S3C2443_PCLKCON_SPI1,
+	}
+};
+
+static struct clk init_clocks[] = {
+	{
+		.name		= "dma",
+		.id		= 0,
+		.parent		= &clk_h,
+		.enable		= s3c2443_clkcon_enable_h,
+		.ctrlbit	= S3C2443_HCLKCON_DMA0,
+	}, {
+		.name		= "dma",
+		.id		= 1,
+		.parent		= &clk_h,
+		.enable		= s3c2443_clkcon_enable_h,
+		.ctrlbit	= S3C2443_HCLKCON_DMA1,
+	}, {
+		.name		= "dma",
+		.id		= 2,
+		.parent		= &clk_h,
+		.enable		= s3c2443_clkcon_enable_h,
+		.ctrlbit	= S3C2443_HCLKCON_DMA2,
+	}, {
+		.name		= "dma",
+		.id		= 3,
+		.parent		= &clk_h,
+		.enable		= s3c2443_clkcon_enable_h,
+		.ctrlbit	= S3C2443_HCLKCON_DMA3,
+	}, {
+		.name		= "dma",
+		.id		= 4,
+		.parent		= &clk_h,
+		.enable		= s3c2443_clkcon_enable_h,
+		.ctrlbit	= S3C2443_HCLKCON_DMA4,
+	}, {
+		.name		= "dma",
+		.id		= 5,
+		.parent		= &clk_h,
+		.enable		= s3c2443_clkcon_enable_h,
+		.ctrlbit	= S3C2443_HCLKCON_DMA5,
+	}, {
+		.name		= "lcd",
+		.id		= -1,
+		.parent		= &clk_h,
+		.enable		= s3c2443_clkcon_enable_h,
+		.ctrlbit	= S3C2443_HCLKCON_LCDC,
+	}, {
+		.name		= "gpio",
+		.id		= -1,
+		.parent		= &clk_p,
+		.enable		= s3c2443_clkcon_enable_p,
+		.ctrlbit	= S3C2443_PCLKCON_GPIO,
+	}, {
+		.name		= "usb-host",
+		.id		= -1,
+		.parent		= &clk_h,
+		.enable		= s3c2443_clkcon_enable_h,
+		.ctrlbit	= S3C2443_HCLKCON_USBH,
+	}, {
+		.name		= "usb-device",
+		.id		= -1,
+		.parent		= &clk_h,
+		.enable		= s3c2443_clkcon_enable_h,
+		.ctrlbit	= S3C2443_HCLKCON_USBD,
+	}, {
+		.name		= "timers",
+		.id		= -1,
+		.parent		= &clk_p,
+		.enable		= s3c2443_clkcon_enable_p,
+		.ctrlbit	= S3C2443_PCLKCON_PWMT,
+	}, {
+		.name		= "uart",
+		.id		= 0,
+		.parent		= &clk_p,
+		.enable		= s3c2443_clkcon_enable_p,
+		.ctrlbit	= S3C2443_PCLKCON_UART0,
+	}, {
+		.name		= "uart",
+		.id		= 1,
+		.parent		= &clk_p,
+		.enable		= s3c2443_clkcon_enable_p,
+		.ctrlbit	= S3C2443_PCLKCON_UART1,
+	}, {
+		.name		= "uart",
+		.id		= 2,
+		.parent		= &clk_p,
+		.enable		= s3c2443_clkcon_enable_p,
+		.ctrlbit	= S3C2443_PCLKCON_UART2,
+	}, {
+		.name		= "uart",
+		.id		= 3,
+		.parent		= &clk_p,
+		.enable		= s3c2443_clkcon_enable_p,
+		.ctrlbit	= S3C2443_PCLKCON_UART3,
+	}, {
+		.name		= "rtc",
+		.id		= -1,
+		.parent		= &clk_p,
+		.enable		= s3c2443_clkcon_enable_p,
+		.ctrlbit	= S3C2443_PCLKCON_RTC,
+	}, {
+		.name		= "watchdog",
+		.id		= -1,
+		.parent		= &clk_p,
+		.ctrlbit	= S3C2443_PCLKCON_WDT,
+	}, {
+		.name		= "usb-bus-host",
+		.id		= -1,
+		.parent		= &clk_usb_bus_host,
+	}
+};
+
+/* clocks to add where we need to check their parentage */
+
+/* s3c2443_clk_initparents
+ *
+ * Initialise the parents for the clocks that we get at start-time
+*/
+
+static int __init clk_init_set_parent(struct clk *clk, struct clk *parent)
+{
+	printk(KERN_DEBUG "clock %s: parent %s\n", clk->name, parent->name);
+	return clk_set_parent(clk, parent);
+}
+
+static void __init s3c2443_clk_initparents(void)
+{
+	unsigned long clksrc = __raw_readl(S3C2443_CLKSRC);
+	struct clk *parent;
+
+	switch (clksrc & S3C2443_CLKSRC_EPLLREF_MASK) {
+	case S3C2443_CLKSRC_EPLLREF_EXTCLK:
+		parent = &clk_ext;
+		break;
+
+	case S3C2443_CLKSRC_EPLLREF_XTAL:
+	default:
+		parent = &clk_xtal;
+		break;
+
+	case S3C2443_CLKSRC_EPLLREF_MPLLREF:
+	case S3C2443_CLKSRC_EPLLREF_MPLLREF2:
+		parent = &clk_mpllref;
+		break;
+	}
+
+	clk_init_set_parent(&clk_epllref, parent);
+
+	switch (clksrc & S3C2443_CLKSRC_I2S_MASK) {
+	case S3C2443_CLKSRC_I2S_EXT:
+		parent = &clk_i2s_ext;
+		break;
+
+	case S3C2443_CLKSRC_I2S_EPLLDIV:
+	default:
+		parent = &clk_i2s_eplldiv;
+		break;
+
+	case S3C2443_CLKSRC_I2S_EPLLREF:
+	case S3C2443_CLKSRC_I2S_EPLLREF3:
+		parent = &clk_epllref;
+	}
+
+	clk_init_set_parent(&clk_i2s, &clk_epllref);
+
+	/* esysclk source */
+
+	parent = (clksrc & S3C2443_CLKSRC_ESYSCLK_EPLL) ?
+		&clk_epll : &clk_epllref;
+
+	clk_init_set_parent(&clk_esysclk, parent);
+
+	/* msysclk source */
+
+	if (clksrc & S3C2443_CLKSRC_MSYSCLK_MPLL) {
+		parent = &clk_mpll;
+	} else {
+		parent = (clksrc & S3C2443_CLKSRC_EXTCLK_DIV) ?
+			&clk_mdivclk : &clk_mpllref;
+	}
+
+	clk_init_set_parent(&clk_msysclk, parent);
+}
+
+/* armdiv divisor table */
+
+static unsigned int armdiv[16] = {
+	[S3C2443_CLKDIV0_ARMDIV_1 >> S3C2443_CLKDIV0_ARMDIV_SHIFT]	= 1,
+	[S3C2443_CLKDIV0_ARMDIV_2 >> S3C2443_CLKDIV0_ARMDIV_SHIFT]	= 2,
+	[S3C2443_CLKDIV0_ARMDIV_3 >> S3C2443_CLKDIV0_ARMDIV_SHIFT]	= 3,
+	[S3C2443_CLKDIV0_ARMDIV_4 >> S3C2443_CLKDIV0_ARMDIV_SHIFT]	= 4,
+	[S3C2443_CLKDIV0_ARMDIV_6 >> S3C2443_CLKDIV0_ARMDIV_SHIFT]	= 6,
+	[S3C2443_CLKDIV0_ARMDIV_8 >> S3C2443_CLKDIV0_ARMDIV_SHIFT]	= 8,
+	[S3C2443_CLKDIV0_ARMDIV_12 >> S3C2443_CLKDIV0_ARMDIV_SHIFT]	= 12,
+	[S3C2443_CLKDIV0_ARMDIV_16 >> S3C2443_CLKDIV0_ARMDIV_SHIFT]	= 16,
+};
+
+static inline unsigned int s3c2443_fclk_div(unsigned long clkcon0)
+{
+	clkcon0 &= S3C2443_CLKDIV0_ARMDIV_MASK;
+
+	return armdiv[clkcon0 >> S3C2443_CLKDIV0_ARMDIV_SHIFT];
+}
+
+static inline unsigned long s3c2443_get_prediv(unsigned long clkcon0)
+{
+	clkcon0 &= S3C2443_CLKDIV0_PREDIV_MASK;
+	clkcon0 >>= S3C2443_CLKDIV0_PREDIV_SHIFT;
+
+	return clkcon0 + 1;
+}
+
+/* clocks to add straight away */
+
+static struct clk *clks[] __initdata = {
+	&clk_ext,
+	&clk_epll,
+	&clk_usb_bus_host,
+	&clk_usb_bus,
+	&clk_esysclk,
+	&clk_epllref,
+	&clk_mpllref,
+	&clk_msysclk,
+	&clk_uart,
+	&clk_display,
+	&clk_cam,
+	&clk_i2s_eplldiv,
+	&clk_i2s,
+	&clk_hsspi,
+	&clk_hsmmc_div,
+	&clk_hsmmc,
+};
+
+void __init s3c2443_init_clocks(int xtal)
+{
+	unsigned long epllcon = __raw_readl(S3C2443_EPLLCON);
+	unsigned long mpllcon = __raw_readl(S3C2443_MPLLCON);
+	unsigned long clkdiv0 = __raw_readl(S3C2443_CLKDIV0);
+	unsigned long pll;
+	unsigned long fclk;
+	unsigned long hclk;
+	unsigned long pclk;
+	struct clk *clkp;
+	int ret;
+	int ptr;
+
+	pll = s3c2443_get_mpll(mpllcon, xtal);
+
+	fclk = pll / s3c2443_fclk_div(clkdiv0);
+	hclk = fclk / s3c2443_get_prediv(clkdiv0);
+	hclk = hclk / ((clkdiv0 & S3C2443_CLKDIV0_HALF_HCLK) ? 2 : 1);
+ 	pclk = hclk / ((clkdiv0 & S3C2443_CLKDIV0_HALF_PCLK) ? 2 : 1);
+
+	s3c24xx_setup_clocks(xtal, fclk, hclk, pclk);
+
+	printk("S3C2443: mpll %s %ld.%03ld MHz, cpu %ld.%03ld MHz, mem %ld.%03ld MHz, pclk %ld.%03ld MHz\n",
+	       (mpllcon & S3C2443_PLLCON_OFF) ? "off":"on",
+	       print_mhz(pll), print_mhz(fclk),
+	       print_mhz(hclk), print_mhz(pclk));
+
+	s3c2443_clk_initparents();
+
+	for (ptr = 0; ptr < ARRAY_SIZE(clks); ptr++) {
+		clkp = clks[ptr];
+
+		ret = s3c24xx_register_clock(clkp);
+		if (ret < 0) {
+			printk(KERN_ERR "Failed to register clock %s (%d)\n",
+			       clkp->name, ret);
+		}
+	}
+
+	clk_epll.rate = s3c2443_get_epll(epllcon, xtal);
+
+	clk_usb_bus.parent = &clk_usb_bus_host;
+
+	/* ensure usb bus clock is within correct rate of 48MHz */
+
+	if (clk_get_rate(&clk_usb_bus_host) != (48 * 1000 * 1000)) {
+		printk(KERN_INFO "Warning: USB host bus not at 48MHz\n");
+		clk_set_rate(&clk_usb_bus_host, 48*1000*1000);
+	}
+
+	printk("S3C2443: epll %s %ld.%03ld MHz, usb-bus %ld.%03ld MHz\n",
+	       (epllcon & S3C2443_PLLCON_OFF) ? "off":"on",
+	       print_mhz(clk_get_rate(&clk_epll)),
+	       print_mhz(clk_get_rate(&clk_usb_bus)));
+
+	/* register clocks from clock array */
+
+	clkp = init_clocks;
+	for (ptr = 0; ptr < ARRAY_SIZE(init_clocks); ptr++, clkp++) {
+		ret = s3c24xx_register_clock(clkp);
+		if (ret < 0) {
+			printk(KERN_ERR "Failed to register clock %s (%d)\n",
+			       clkp->name, ret);
+		}
+	}
+
+	/* We must be careful disabling the clocks we are not intending to
+	 * be using at boot time, as subsytems such as the LCD which do
+	 * their own DMA requests to the bus can cause the system to lockup
+	 * if they where in the middle of requesting bus access.
+	 *
+	 * Disabling the LCD clock if the LCD is active is very dangerous,
+	 * and therefore the bootloader should be careful to not enable
+	 * the LCD clock if it is not needed.
+	*/
+
+	/* install (and disable) the clocks we do not need immediately */
+
+	clkp = init_clocks_disable;
+	for (ptr = 0; ptr < ARRAY_SIZE(init_clocks_disable); ptr++, clkp++) {
+
+		ret = s3c24xx_register_clock(clkp);
+		if (ret < 0) {
+			printk(KERN_ERR "Failed to register clock %s (%d)\n",
+			       clkp->name, ret);
+		}
+
+		(clkp->enable)(clkp, 0);
+	}
+}
diff --git a/arch/arm/mach-s3c2443/dma.c b/arch/arm/mach-s3c2443/dma.c
new file mode 100644
index 00000000000..f70e8ccffc3
--- /dev/null
+++ b/arch/arm/mach-s3c2443/dma.c
@@ -0,0 +1,180 @@
+/* linux/arch/arm/mach-s3c2443/dma.c
+ *
+ * Copyright (c) 2007 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C2443 DMA selection
+ *
+ * http://armlinux.simtec.co.uk/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/sysdev.h>
+#include <linux/serial_core.h>
+
+#include <asm/dma.h>
+#include <asm/arch/dma.h>
+#include <asm/io.h>
+
+#include <asm/plat-s3c24xx/dma.h>
+#include <asm/plat-s3c24xx/cpu.h>
+
+#include <asm/arch/regs-serial.h>
+#include <asm/arch/regs-gpio.h>
+#include <asm/arch/regs-ac97.h>
+#include <asm/arch/regs-mem.h>
+#include <asm/arch/regs-lcd.h>
+#include <asm/arch/regs-sdi.h>
+#include <asm/arch/regs-iis.h>
+#include <asm/arch/regs-spi.h>
+
+#define MAP(x) { \
+		[0]	= (x) | DMA_CH_VALID,	\
+		[1]	= (x) | DMA_CH_VALID,	\
+		[2]	= (x) | DMA_CH_VALID,	\
+		[3]	= (x) | DMA_CH_VALID,	\
+		[4]	= (x) | DMA_CH_VALID,	\
+		[5]     = (x) | DMA_CH_VALID,	\
+	}
+
+static struct s3c24xx_dma_map __initdata s3c2443_dma_mappings[] = {
+	[DMACH_XD0] = {
+		.name		= "xdreq0",
+		.channels	= MAP(S3C2443_DMAREQSEL_XDREQ0),
+	},
+	[DMACH_XD1] = {
+		.name		= "xdreq1",
+		.channels	= MAP(S3C2443_DMAREQSEL_XDREQ1),
+	},
+	[DMACH_SDI] = {
+		.name		= "sdi",
+		.channels	= MAP(S3C2443_DMAREQSEL_SDI),
+		.hw_addr.to	= S3C2410_PA_IIS + S3C2410_IISFIFO,
+		.hw_addr.from	= S3C2410_PA_IIS + S3C2410_IISFIFO,
+	},
+	[DMACH_SPI0] = {
+		.name		= "spi0",
+		.channels	= MAP(S3C2443_DMAREQSEL_SPI0TX),
+		.hw_addr.to	= S3C2410_PA_SPI + S3C2410_SPTDAT,
+		.hw_addr.from	= S3C2410_PA_SPI + S3C2410_SPRDAT,
+	},
+	[DMACH_SPI1] = {
+		.name		= "spi1",
+		.channels	= MAP(S3C2443_DMAREQSEL_SPI1TX),
+		.hw_addr.to	= S3C2410_PA_SPI + 0x20 + S3C2410_SPTDAT,
+		.hw_addr.from	= S3C2410_PA_SPI + 0x20 + S3C2410_SPRDAT,
+	},
+	[DMACH_UART0] = {
+		.name		= "uart0",
+		.channels	= MAP(S3C2443_DMAREQSEL_UART0_0),
+		.hw_addr.to	= S3C2410_PA_UART0 + S3C2410_UTXH,
+		.hw_addr.from	= S3C2410_PA_UART0 + S3C2410_URXH,
+	},
+	[DMACH_UART1] = {
+		.name		= "uart1",
+		.channels	= MAP(S3C2443_DMAREQSEL_UART1_0),
+		.hw_addr.to	= S3C2410_PA_UART1 + S3C2410_UTXH,
+		.hw_addr.from	= S3C2410_PA_UART1 + S3C2410_URXH,
+	},
+      	[DMACH_UART2] = {
+		.name		= "uart2",
+		.channels	= MAP(S3C2443_DMAREQSEL_UART2_0),
+		.hw_addr.to	= S3C2410_PA_UART2 + S3C2410_UTXH,
+		.hw_addr.from	= S3C2410_PA_UART2 + S3C2410_URXH,
+	},
+      	[DMACH_UART3] = {
+		.name		= "uart3",
+		.channels	= MAP(S3C2443_DMAREQSEL_UART3_0),
+		.hw_addr.to	= S3C2443_PA_UART3 + S3C2410_UTXH,
+		.hw_addr.from	= S3C2443_PA_UART3 + S3C2410_URXH,
+	},
+	[DMACH_UART0_SRC2] = {
+		.name		= "uart0",
+		.channels	= MAP(S3C2443_DMAREQSEL_UART0_1),
+		.hw_addr.to	= S3C2410_PA_UART0 + S3C2410_UTXH,
+		.hw_addr.from	= S3C2410_PA_UART0 + S3C2410_URXH,
+	},
+	[DMACH_UART1_SRC2] = {
+		.name		= "uart1",
+		.channels	= MAP(S3C2443_DMAREQSEL_UART1_1),
+		.hw_addr.to	= S3C2410_PA_UART1 + S3C2410_UTXH,
+		.hw_addr.from	= S3C2410_PA_UART1 + S3C2410_URXH,
+	},
+      	[DMACH_UART2_SRC2] = {
+		.name		= "uart2",
+		.channels	= MAP(S3C2443_DMAREQSEL_UART2_1),
+		.hw_addr.to	= S3C2410_PA_UART2 + S3C2410_UTXH,
+		.hw_addr.from	= S3C2410_PA_UART2 + S3C2410_URXH,
+	},
+      	[DMACH_UART3_SRC2] = {
+		.name		= "uart3",
+		.channels	= MAP(S3C2443_DMAREQSEL_UART3_1),
+		.hw_addr.to	= S3C2443_PA_UART3 + S3C2410_UTXH,
+		.hw_addr.from	= S3C2443_PA_UART3 + S3C2410_URXH,
+	},
+	[DMACH_TIMER] = {
+		.name		= "timer",
+		.channels	= MAP(S3C2443_DMAREQSEL_TIMER),
+	},
+	[DMACH_I2S_IN] = {
+		.name		= "i2s-sdi",
+		.channels	= MAP(S3C2443_DMAREQSEL_I2SRX),
+		.hw_addr.from	= S3C2410_PA_IIS + S3C2410_IISFIFO,
+	},
+	[DMACH_I2S_OUT] = {
+		.name		= "i2s-sdo",
+		.channels	= MAP(S3C2443_DMAREQSEL_I2STX),
+		.hw_addr.to	= S3C2410_PA_IIS + S3C2410_IISFIFO,
+	},
+	[DMACH_PCM_IN] = {
+		.name		= "pcm-in",
+		.channels	= MAP(S3C2443_DMAREQSEL_PCMIN),
+		.hw_addr.from	= S3C2440_PA_AC97 + S3C_AC97_PCM_DATA,
+	},
+	[DMACH_PCM_OUT] = {
+		.name		= "pcm-out",
+		.channels	= MAP(S3C2443_DMAREQSEL_PCMOUT),
+		.hw_addr.to	= S3C2440_PA_AC97 + S3C_AC97_PCM_DATA,
+	},
+	[DMACH_MIC_IN] = {
+		.name		= "mic-in",
+		.channels	= MAP(S3C2443_DMAREQSEL_MICIN),
+		.hw_addr.from	= S3C2440_PA_AC97 + S3C_AC97_MIC_DATA,
+	},
+};
+
+static void s3c2443_dma_select(struct s3c2410_dma_chan *chan,
+			       struct s3c24xx_dma_map *map)
+{
+	writel(map->channels[0] | S3C2443_DMAREQSEL_HW,
+	       chan->regs + S3C2443_DMA_DMAREQSEL);
+}
+
+static struct s3c24xx_dma_selection __initdata s3c2443_dma_sel = {
+	.select		= s3c2443_dma_select,
+	.dcon_mask	= 0,
+	.map		= s3c2443_dma_mappings,
+	.map_size	= ARRAY_SIZE(s3c2443_dma_mappings),
+};
+
+static int s3c2443_dma_add(struct sys_device *sysdev)
+{
+	s3c24xx_dma_init(6, IRQ_S3C2443_DMA0, 0x100);
+	return s3c24xx_dma_init_map(&s3c2443_dma_sel);
+}
+
+static struct sysdev_driver s3c2443_dma_driver = {
+	.add	= s3c2443_dma_add,
+};
+
+static int __init s3c2443_dma_init(void)
+{
+	return sysdev_driver_register(&s3c2443_sysclass, &s3c2443_dma_driver);
+}
+
+arch_initcall(s3c2443_dma_init);
diff --git a/arch/arm/mach-s3c2443/irq.c b/arch/arm/mach-s3c2443/irq.c
new file mode 100644
index 00000000000..7a45b6dcb73
--- /dev/null
+++ b/arch/arm/mach-s3c2443/irq.c
@@ -0,0 +1,290 @@
+/* linux/arch/arm/mach-s3c2443/irq.c
+ *
+ * Copyright (c) 2007 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ *
+*/
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/ptrace.h>
+#include <linux/sysdev.h>
+
+#include <asm/hardware.h>
+#include <asm/irq.h>
+#include <asm/io.h>
+
+#include <asm/mach/irq.h>
+
+#include <asm/arch/regs-irq.h>
+#include <asm/arch/regs-gpio.h>
+
+#include <asm/plat-s3c24xx/cpu.h>
+#include <asm/plat-s3c24xx/pm.h>
+#include <asm/plat-s3c24xx/irq.h>
+
+#define INTMSK(start, end) ((1 << ((end) + 1 - (start))) - 1)
+
+static inline void s3c2443_irq_demux(unsigned int irq, unsigned int len)
+{
+	unsigned int subsrc, submsk;
+	unsigned int end;
+	struct irq_desc *mydesc;
+
+	/* read the current pending interrupts, and the mask
+	 * for what it is available */
+
+	subsrc = __raw_readl(S3C2410_SUBSRCPND);
+	submsk = __raw_readl(S3C2410_INTSUBMSK);
+
+	subsrc  &= ~submsk;
+	subsrc >>= (irq - S3C2410_IRQSUB(0));
+	subsrc  &= (1 << len)-1;
+
+	end = len + irq;
+	mydesc = irq_desc + irq;
+
+	for (; irq < end && subsrc; irq++) {
+		if (subsrc & 1)
+			desc_handle_irq(irq, mydesc);
+
+		mydesc++;
+		subsrc >>= 1;
+	}
+}
+
+/* WDT/AC97 sub interrupts */
+
+static void s3c2443_irq_demux_wdtac97(unsigned int irq, struct irq_desc *desc)
+{
+	s3c2443_irq_demux(IRQ_S3C2443_WDT, 4);
+}
+
+#define INTMSK_WDTAC97	(1UL << (IRQ_WDT - IRQ_EINT0))
+#define SUBMSK_WDTAC97	INTMSK(IRQ_S3C2443_WDT, IRQ_S3C2443_AC97)
+
+static void s3c2443_irq_wdtac97_mask(unsigned int irqno)
+{
+	s3c_irqsub_mask(irqno, INTMSK_WDTAC97, SUBMSK_WDTAC97);
+}
+
+static void s3c2443_irq_wdtac97_unmask(unsigned int irqno)
+{
+	s3c_irqsub_unmask(irqno, INTMSK_WDTAC97);
+}
+
+static void s3c2443_irq_wdtac97_ack(unsigned int irqno)
+{
+	s3c_irqsub_maskack(irqno, INTMSK_WDTAC97, SUBMSK_WDTAC97);
+}
+
+static struct irq_chip s3c2443_irq_wdtac97 = {
+	.mask	    = s3c2443_irq_wdtac97_mask,
+	.unmask	    = s3c2443_irq_wdtac97_unmask,
+	.ack	    = s3c2443_irq_wdtac97_ack,
+};
+
+
+/* LCD sub interrupts */
+
+static void s3c2443_irq_demux_lcd(unsigned int irq, struct irq_desc *desc)
+{
+	s3c2443_irq_demux(IRQ_S3C2443_LCD1, 4);
+}
+
+#define INTMSK_LCD	(1UL << (IRQ_LCD - IRQ_EINT0))
+#define SUBMSK_LCD	INTMSK(IRQ_S3C2443_LCD1, IRQ_S3C2443_LCD4)
+
+static void s3c2443_irq_lcd_mask(unsigned int irqno)
+{
+	s3c_irqsub_mask(irqno, INTMSK_LCD, SUBMSK_LCD);
+}
+
+static void s3c2443_irq_lcd_unmask(unsigned int irqno)
+{
+	s3c_irqsub_unmask(irqno, INTMSK_LCD);
+}
+
+static void s3c2443_irq_lcd_ack(unsigned int irqno)
+{
+	s3c_irqsub_maskack(irqno, INTMSK_LCD, SUBMSK_LCD);
+}
+
+static struct irq_chip s3c2443_irq_lcd = {
+	.mask	    = s3c2443_irq_lcd_mask,
+	.unmask	    = s3c2443_irq_lcd_unmask,
+	.ack	    = s3c2443_irq_lcd_ack,
+};
+
+
+/* DMA sub interrupts */
+
+static void s3c2443_irq_demux_dma(unsigned int irq, struct irq_desc *desc)
+{
+	s3c2443_irq_demux(IRQ_S3C2443_DMA1, 6);
+}
+
+#define INTMSK_DMA	(1UL << (IRQ_S3C2443_DMA - IRQ_EINT0))
+#define SUBMSK_DMA	INTMSK(IRQ_S3C2443_DMA0, IRQ_S3C2443_DMA5)
+
+
+static void s3c2443_irq_dma_mask(unsigned int irqno)
+{
+	s3c_irqsub_mask(irqno, INTMSK_DMA, SUBMSK_DMA);
+}
+
+static void s3c2443_irq_dma_unmask(unsigned int irqno)
+{
+	s3c_irqsub_unmask(irqno, INTMSK_DMA);
+}
+
+static void s3c2443_irq_dma_ack(unsigned int irqno)
+{
+	s3c_irqsub_maskack(irqno, INTMSK_DMA, SUBMSK_DMA);
+}
+
+static struct irq_chip s3c2443_irq_dma = {
+	.mask	    = s3c2443_irq_dma_mask,
+	.unmask	    = s3c2443_irq_dma_unmask,
+	.ack	    = s3c2443_irq_dma_ack,
+};
+
+
+/* UART3 sub interrupts */
+
+static void s3c2443_irq_demux_uart3(unsigned int irq, struct irq_desc *desc)
+{
+	s3c2443_irq_demux(IRQ_S3C2443_UART3, 3);
+}
+
+#define INTMSK_UART3	(1UL << (IRQ_S3C2443_UART3 - IRQ_EINT0))
+#define SUBMSK_UART3	(0xf << (IRQ_S3C2443_RX3 - S3C2410_IRQSUB(0)))
+
+
+static void s3c2443_irq_uart3_mask(unsigned int irqno)
+{
+	s3c_irqsub_mask(irqno, INTMSK_UART3, SUBMSK_UART3);
+}
+
+static void s3c2443_irq_uart3_unmask(unsigned int irqno)
+{
+	s3c_irqsub_unmask(irqno, INTMSK_UART3);
+}
+
+static void s3c2443_irq_uart3_ack(unsigned int irqno)
+{
+	s3c_irqsub_maskack(irqno, INTMSK_UART3, SUBMSK_UART3);
+}
+
+static struct irq_chip s3c2443_irq_uart3 = {
+	.mask	    = s3c2443_irq_uart3_mask,
+	.unmask	    = s3c2443_irq_uart3_unmask,
+	.ack	    = s3c2443_irq_uart3_ack,
+};
+
+
+/* CAM sub interrupts */
+
+static void s3c2443_irq_demux_cam(unsigned int irq, struct irq_desc *desc)
+{
+	s3c2443_irq_demux(IRQ_S3C2440_CAM_C, 4);
+}
+
+#define INTMSK_CAM	(1UL << (IRQ_CAM - IRQ_EINT0))
+#define SUBMSK_CAM	INTMSK(IRQ_S3C2440_CAM_C, IRQ_S3C2440_CAM_P)
+
+static void s3c2443_irq_cam_mask(unsigned int irqno)
+{
+	s3c_irqsub_mask(irqno, INTMSK_CAM, SUBMSK_CAM);
+}
+
+static void s3c2443_irq_cam_unmask(unsigned int irqno)
+{
+	s3c_irqsub_unmask(irqno, INTMSK_CAM);
+}
+
+static void s3c2443_irq_cam_ack(unsigned int irqno)
+{
+	s3c_irqsub_maskack(irqno, INTMSK_CAM, SUBMSK_CAM);
+}
+
+static struct irq_chip s3c2443_irq_cam = {
+	.mask	    = s3c2443_irq_cam_mask,
+	.unmask	    = s3c2443_irq_cam_unmask,
+	.ack	    = s3c2443_irq_cam_ack,
+};
+
+/* IRQ initialisation code */
+
+static int __init s3c2443_add_sub(unsigned int base,
+				   void (*demux)(unsigned int,
+						 struct irq_desc *),
+				   struct irq_chip *chip,
+				   unsigned int start, unsigned int end)
+{
+	unsigned int irqno;
+
+	set_irq_chip(base, &s3c_irq_level_chip);
+	set_irq_handler(base, handle_level_irq);
+	set_irq_chained_handler(base, demux);
+
+	for (irqno = start; irqno <= end; irqno++) {
+		set_irq_chip(irqno, chip);
+		set_irq_handler(irqno, handle_level_irq);
+		set_irq_flags(irqno, IRQF_VALID);
+	}
+
+	return 0;
+}
+
+static int s3c2443_irq_add(struct sys_device *sysdev)
+{
+	printk("S3C2443: IRQ Support\n");
+
+	s3c2443_add_sub(IRQ_CAM, s3c2443_irq_demux_cam, &s3c2443_irq_cam,
+			IRQ_S3C2440_CAM_C, IRQ_S3C2440_CAM_P);
+
+	s3c2443_add_sub(IRQ_LCD, s3c2443_irq_demux_lcd, &s3c2443_irq_lcd,
+			IRQ_S3C2443_LCD1, IRQ_S3C2443_LCD4);
+
+	s3c2443_add_sub(IRQ_S3C2443_DMA, s3c2443_irq_demux_dma,
+			&s3c2443_irq_dma, IRQ_S3C2443_DMA0, IRQ_S3C2443_DMA5);
+
+	s3c2443_add_sub(IRQ_S3C2443_UART3, s3c2443_irq_demux_uart3,
+			&s3c2443_irq_uart3,
+			IRQ_S3C2443_RX3, IRQ_S3C2443_ERR3);
+
+	s3c2443_add_sub(IRQ_WDT, s3c2443_irq_demux_wdtac97,
+			&s3c2443_irq_wdtac97,
+			IRQ_S3C2443_WDT, IRQ_S3C2443_AC97);
+
+	return 0;
+}
+
+static struct sysdev_driver s3c2443_irq_driver = {
+	.add		= s3c2443_irq_add,
+};
+
+static int s3c2443_irq_init(void)
+{
+	return sysdev_driver_register(&s3c2443_sysclass, &s3c2443_irq_driver);
+}
+
+arch_initcall(s3c2443_irq_init);
+
diff --git a/arch/arm/mach-s3c2443/mach-smdk2443.c b/arch/arm/mach-s3c2443/mach-smdk2443.c
new file mode 100644
index 00000000000..e82aaff7dee
--- /dev/null
+++ b/arch/arm/mach-s3c2443/mach-smdk2443.c
@@ -0,0 +1,137 @@
+/* linux/arch/arm/mach-s3c2443/mach-smdk2443.c
+ *
+ * Copyright (c) 2007 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * http://www.fluff.org/ben/smdk2443/
+ *
+ * Thanks to Samsung for the loan of an SMDK2443
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+*/
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/timer.h>
+#include <linux/init.h>
+#include <linux/serial_core.h>
+#include <linux/platform_device.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <asm/hardware.h>
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/mach-types.h>
+
+#include <asm/arch/regs-serial.h>
+#include <asm/arch/regs-gpio.h>
+#include <asm/arch/regs-lcd.h>
+
+#include <asm/arch/idle.h>
+#include <asm/arch/fb.h>
+
+#include <asm/plat-s3c24xx/s3c2410.h>
+#include <asm/plat-s3c24xx/s3c2440.h>
+#include <asm/plat-s3c24xx/clock.h>
+#include <asm/plat-s3c24xx/devs.h>
+#include <asm/plat-s3c24xx/cpu.h>
+
+#include <asm/plat-s3c24xx/common-smdk.h>
+
+static struct map_desc smdk2443_iodesc[] __initdata = {
+	/* ISA IO Space map (memory space selected by A24) */
+
+	{
+		.virtual	= (u32)S3C24XX_VA_ISA_WORD,
+		.pfn		= __phys_to_pfn(S3C2410_CS2),
+		.length		= 0x10000,
+		.type		= MT_DEVICE,
+	}, {
+		.virtual	= (u32)S3C24XX_VA_ISA_WORD + 0x10000,
+		.pfn		= __phys_to_pfn(S3C2410_CS2 + (1<<24)),
+		.length		= SZ_4M,
+		.type		= MT_DEVICE,
+	}, {
+		.virtual	= (u32)S3C24XX_VA_ISA_BYTE,
+		.pfn		= __phys_to_pfn(S3C2410_CS2),
+		.length		= 0x10000,
+		.type		= MT_DEVICE,
+	}, {
+		.virtual	= (u32)S3C24XX_VA_ISA_BYTE + 0x10000,
+		.pfn		= __phys_to_pfn(S3C2410_CS2 + (1<<24)),
+		.length		= SZ_4M,
+		.type		= MT_DEVICE,
+	}
+};
+
+#define UCON S3C2410_UCON_DEFAULT | S3C2410_UCON_UCLK
+#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB
+#define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE
+
+static struct s3c2410_uartcfg smdk2443_uartcfgs[] __initdata = {
+	[0] = {
+		.hwport	     = 0,
+		.flags	     = 0,
+		.ucon	     = 0x3c5,
+		.ulcon	     = 0x03,
+		.ufcon	     = 0x51,
+	},
+	[1] = {
+		.hwport	     = 1,
+		.flags	     = 0,
+		.ucon	     = 0x3c5,
+		.ulcon	     = 0x03,
+		.ufcon	     = 0x51,
+	},
+	/* IR port */
+	[2] = {
+		.hwport	     = 2,
+		.flags	     = 0,
+		.ucon	     = 0x3c5,
+		.ulcon	     = 0x43,
+		.ufcon	     = 0x51,
+	}
+};
+
+static struct platform_device *smdk2443_devices[] __initdata = {
+	&s3c_device_wdt,
+	&s3c_device_i2c,
+};
+
+static struct s3c24xx_board smdk2443_board __initdata = {
+	.devices       = smdk2443_devices,
+	.devices_count = ARRAY_SIZE(smdk2443_devices)
+};
+
+static void __init smdk2443_map_io(void)
+{
+	s3c24xx_init_io(smdk2443_iodesc, ARRAY_SIZE(smdk2443_iodesc));
+	s3c24xx_init_clocks(12000000);
+	s3c24xx_init_uarts(smdk2443_uartcfgs, ARRAY_SIZE(smdk2443_uartcfgs));
+	s3c24xx_set_board(&smdk2443_board);
+}
+
+static void __init smdk2443_machine_init(void)
+{
+	smdk_machine_init();
+}
+
+MACHINE_START(SMDK2443, "SMDK2443")
+	/* Maintainer: Ben Dooks <ben@fluff.org> */
+	.phys_io	= S3C2410_PA_UART,
+	.io_pg_offst	= (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc,
+	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+
+	.init_irq	= s3c24xx_init_irq,
+	.map_io		= smdk2443_map_io,
+	.init_machine	= smdk2443_machine_init,
+	.timer		= &s3c24xx_timer,
+MACHINE_END
diff --git a/arch/arm/mach-s3c2443/s3c2443.c b/arch/arm/mach-s3c2443/s3c2443.c
new file mode 100644
index 00000000000..11b1d0b310c
--- /dev/null
+++ b/arch/arm/mach-s3c2443/s3c2443.c
@@ -0,0 +1,97 @@
+/* linux/arch/arm/mach-s3c2443/s3c2443.c
+ *
+ * Copyright (c) 2007 Simtec Electronics
+ *   Ben Dooks <ben@simtec.co.uk>
+ *
+ * Samsung S3C2443 Mobile CPU support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/timer.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/serial_core.h>
+#include <linux/sysdev.h>
+#include <linux/clk.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <asm/hardware.h>
+#include <asm/io.h>
+#include <asm/irq.h>
+
+#include <asm/arch/regs-s3c2443-clock.h>
+#include <asm/arch/reset.h>
+
+#include <asm/plat-s3c24xx/s3c2443.h>
+#include <asm/plat-s3c24xx/devs.h>
+#include <asm/plat-s3c24xx/cpu.h>
+
+static struct map_desc s3c2443_iodesc[] __initdata = {
+	IODESC_ENT(WATCHDOG),
+	IODESC_ENT(CLKPWR),
+	IODESC_ENT(TIMER),
+};
+
+struct sysdev_class s3c2443_sysclass = {
+	set_kset_name("s3c2443-core"),
+};
+
+static struct sys_device s3c2443_sysdev = {
+	.cls		= &s3c2443_sysclass,
+};
+
+static void s3c2443_hard_reset(void)
+{
+	__raw_writel(S3C2443_SWRST_RESET, S3C2443_SWRST);
+}
+
+int __init s3c2443_init(void)
+{
+	printk("S3C2443: Initialising architecture\n");
+
+	s3c24xx_reset_hook = s3c2443_hard_reset;
+
+	s3c_device_nand.name = "s3c2412-nand";
+
+	return sysdev_register(&s3c2443_sysdev);
+}
+
+void __init s3c2443_init_uarts(struct s3c2410_uartcfg *cfg, int no)
+{
+	s3c24xx_init_uartdevs("s3c2440-uart", s3c2410_uart_resources, cfg, no);
+}
+
+/* s3c2443_map_io
+ *
+ * register the standard cpu IO areas, and any passed in from the
+ * machine specific initialisation.
+ */
+
+void __init s3c2443_map_io(struct map_desc *mach_desc, int mach_size)
+{
+	iotable_init(s3c2443_iodesc, ARRAY_SIZE(s3c2443_iodesc));
+	iotable_init(mach_desc, mach_size);
+}
+
+/* need to register class before we actually register the device, and
+ * we also need to ensure that it has been initialised before any of the
+ * drivers even try to use it (even if not on an s3c2443 based system)
+ * as a driver which may support both 2443 and 2440 may try and use it.
+*/
+
+static int __init s3c2443_core_init(void)
+{
+	return sysdev_class_register(&s3c2443_sysclass);
+}
+
+core_initcall(s3c2443_core_init);
diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig
index aade2f72c92..4b277199d0e 100644
--- a/arch/arm/mm/Kconfig
+++ b/arch/arm/mm/Kconfig
@@ -171,8 +171,8 @@ config CPU_ARM925T
 # ARM926T
 config CPU_ARM926T
 	bool "Support ARM926T processor"
-	depends on ARCH_INTEGRATOR || ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || MACH_REALVIEW_EB || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261
-	default y if ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261
+	depends on ARCH_INTEGRATOR || ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || MACH_REALVIEW_EB || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_NS9XXX
+	default y if ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_NS9XXX
 	select CPU_32v5
 	select CPU_ABRT_EV5TJ
 	select CPU_CACHE_VIVT
@@ -609,3 +609,10 @@ config NEEDS_SYSCALL_FOR_CMPXCHG
 	  Forget about fast user space cmpxchg support.
 	  It is just not possible.
 
+config OUTER_CACHE
+	bool
+	default n
+
+config CACHE_L2X0
+	bool
+	select OUTER_CACHE
diff --git a/arch/arm/mm/Makefile b/arch/arm/mm/Makefile
index d2f5672ecf6..2f8b9594777 100644
--- a/arch/arm/mm/Makefile
+++ b/arch/arm/mm/Makefile
@@ -66,3 +66,5 @@ obj-$(CONFIG_CPU_SA1100)	+= proc-sa1100.o
 obj-$(CONFIG_CPU_XSCALE)	+= proc-xscale.o
 obj-$(CONFIG_CPU_XSC3)		+= proc-xsc3.o
 obj-$(CONFIG_CPU_V6)		+= proc-v6.o
+
+obj-$(CONFIG_CACHE_L2X0)	+= cache-l2x0.o
diff --git a/arch/arm/mm/cache-l2x0.c b/arch/arm/mm/cache-l2x0.c
new file mode 100644
index 00000000000..08a36f1b35d
--- /dev/null
+++ b/arch/arm/mm/cache-l2x0.c
@@ -0,0 +1,104 @@
+/*
+ * arch/arm/mm/cache-l2x0.c - L210/L220 cache controller support
+ *
+ * Copyright (C) 2007 ARM Limited
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+#include <linux/init.h>
+
+#include <asm/cacheflush.h>
+#include <asm/io.h>
+#include <asm/hardware/cache-l2x0.h>
+
+#define CACHE_LINE_SIZE		32
+
+static void __iomem *l2x0_base;
+
+static inline void sync_writel(unsigned long val, unsigned long reg,
+			       unsigned long complete_mask)
+{
+	writel(val, l2x0_base + reg);
+	/* wait for the operation to complete */
+	while (readl(l2x0_base + reg) & complete_mask)
+		;
+}
+
+static inline void cache_sync(void)
+{
+	sync_writel(0, L2X0_CACHE_SYNC, 1);
+}
+
+static inline void l2x0_inv_all(void)
+{
+	/* invalidate all ways */
+	sync_writel(0xff, L2X0_INV_WAY, 0xff);
+	cache_sync();
+}
+
+static void l2x0_inv_range(unsigned long start, unsigned long end)
+{
+	unsigned long addr;
+
+	start &= ~(CACHE_LINE_SIZE - 1);
+	for (addr = start; addr < end; addr += CACHE_LINE_SIZE)
+		sync_writel(addr, L2X0_INV_LINE_PA, 1);
+	cache_sync();
+}
+
+static void l2x0_clean_range(unsigned long start, unsigned long end)
+{
+	unsigned long addr;
+
+	start &= ~(CACHE_LINE_SIZE - 1);
+	for (addr = start; addr < end; addr += CACHE_LINE_SIZE)
+		sync_writel(addr, L2X0_CLEAN_LINE_PA, 1);
+	cache_sync();
+}
+
+static void l2x0_flush_range(unsigned long start, unsigned long end)
+{
+	unsigned long addr;
+
+	start &= ~(CACHE_LINE_SIZE - 1);
+	for (addr = start; addr < end; addr += CACHE_LINE_SIZE)
+		sync_writel(addr, L2X0_CLEAN_INV_LINE_PA, 1);
+	cache_sync();
+}
+
+void __init l2x0_init(void __iomem *base, __u32 aux_val, __u32 aux_mask)
+{
+	__u32 aux;
+
+	l2x0_base = base;
+
+	/* disable L2X0 */
+	writel(0, l2x0_base + L2X0_CTRL);
+
+	aux = readl(l2x0_base + L2X0_AUX_CTRL);
+	aux &= aux_mask;
+	aux |= aux_val;
+	writel(aux, l2x0_base + L2X0_AUX_CTRL);
+
+	l2x0_inv_all();
+
+	/* enable L2X0 */
+	writel(1, l2x0_base + L2X0_CTRL);
+
+	outer_cache.inv_range = l2x0_inv_range;
+	outer_cache.clean_range = l2x0_clean_range;
+	outer_cache.flush_range = l2x0_flush_range;
+
+	printk(KERN_INFO "L2X0 cache controller enabled\n");
+}
diff --git a/arch/arm/mm/consistent.c b/arch/arm/mm/consistent.c
index 6a9c362fef5..1f9f94f9af4 100644
--- a/arch/arm/mm/consistent.c
+++ b/arch/arm/mm/consistent.c
@@ -205,9 +205,10 @@ __dma_alloc(struct device *dev, size_t size, dma_addr_t *handle, gfp_t gfp,
 	 * kernel direct-mapped region for device DMA.
 	 */
 	{
-		unsigned long kaddr = (unsigned long)page_address(page);
-		memset(page_address(page), 0, size);
-		dmac_flush_range(kaddr, kaddr + size);
+		void *ptr = page_address(page);
+		memset(ptr, 0, size);
+		dmac_flush_range(ptr, ptr + size);
+		outer_flush_range(__pa(ptr), __pa(ptr) + size);
 	}
 
 	/*
@@ -480,20 +481,24 @@ core_initcall(consistent_init);
  * platforms with CONFIG_DMABOUNCE.
  * Use the driver DMA support - see dma-mapping.h (dma_sync_*)
  */
-void consistent_sync(void *vaddr, size_t size, int direction)
+void consistent_sync(const void *start, size_t size, int direction)
 {
-	unsigned long start = (unsigned long)vaddr;
-	unsigned long end   = start + size;
+	const void *end = start + size;
+
+	BUG_ON(!virt_addr_valid(start) || !virt_addr_valid(end - 1));
 
 	switch (direction) {
 	case DMA_FROM_DEVICE:		/* invalidate only */
 		dmac_inv_range(start, end);
+		outer_inv_range(__pa(start), __pa(end));
 		break;
 	case DMA_TO_DEVICE:		/* writeback only */
 		dmac_clean_range(start, end);
+		outer_clean_range(__pa(start), __pa(end));
 		break;
 	case DMA_BIDIRECTIONAL:		/* writeback and invalidate */
 		dmac_flush_range(start, end);
+		outer_flush_range(__pa(start), __pa(end));
 		break;
 	default:
 		BUG();
diff --git a/arch/arm/mm/context.c b/arch/arm/mm/context.c
index 79e80020242..9da43a0fdcd 100644
--- a/arch/arm/mm/context.c
+++ b/arch/arm/mm/context.c
@@ -19,7 +19,8 @@ unsigned int cpu_last_asid = { 1 << ASID_BITS };
 /*
  * We fork()ed a process, and we need a new context for the child
  * to run in.  We reserve version 0 for initial tasks so we will
- * always allocate an ASID.
+ * always allocate an ASID. The ASID 0 is reserved for the TTBR
+ * register changing sequence.
  */
 void __init_new_context(struct task_struct *tsk, struct mm_struct *mm)
 {
@@ -38,8 +39,15 @@ void __new_context(struct mm_struct *mm)
 	 * If we've used up all our ASIDs, we need
 	 * to start a new version and flush the TLB.
 	 */
-	if ((asid & ~ASID_MASK) == 0)
+	if ((asid & ~ASID_MASK) == 0) {
+		asid = ++cpu_last_asid;
+		/* set the reserved ASID before flushing the TLB */
+		asm("mcr	p15, 0, %0, c13, c0, 1	@ set reserved context ID\n"
+		    :
+		    : "r" (0));
+		isb();
 		flush_tlb_all();
+	}
 
 	mm->context.id = asid;
 }
diff --git a/arch/arm/mm/fault-armv.c b/arch/arm/mm/fault-armv.c
index cf95c5d0ce4..44558d5f931 100644
--- a/arch/arm/mm/fault-armv.c
+++ b/arch/arm/mm/fault-armv.c
@@ -119,8 +119,6 @@ make_coherent(struct address_space *mapping, struct vm_area_struct *vma, unsigne
 		flush_cache_page(vma, addr, pfn);
 }
 
-void __flush_dcache_page(struct address_space *mapping, struct page *page);
-
 /*
  * Take care of architecture specific things when placing a new PTE into
  * a page table, or changing an existing PTE.  Basically, there are two
diff --git a/arch/arm/mm/mmu.c b/arch/arm/mm/mmu.c
index 655c8376f0b..94fd4bf5cb9 100644
--- a/arch/arm/mm/mmu.c
+++ b/arch/arm/mm/mmu.c
@@ -49,8 +49,10 @@ pmd_t *top_pmd;
 
 static unsigned int cachepolicy __initdata = CPOLICY_WRITEBACK;
 static unsigned int ecc_mask __initdata = 0;
+pgprot_t pgprot_user;
 pgprot_t pgprot_kernel;
 
+EXPORT_SYMBOL(pgprot_user);
 EXPORT_SYMBOL(pgprot_kernel);
 
 struct cachepolicy {
@@ -345,6 +347,7 @@ static void __init build_mem_type_table(void)
 		mem_types[MT_MINICLEAN].prot_sect &= ~PMD_SECT_TEX(1);
 	}
 
+	pgprot_user   = __pgprot(L_PTE_PRESENT | L_PTE_YOUNG | user_pgprot);
 	pgprot_kernel = __pgprot(L_PTE_PRESENT | L_PTE_YOUNG |
 				 L_PTE_DIRTY | L_PTE_WRITE |
 				 L_PTE_EXEC | kern_pgprot);
diff --git a/arch/arm/mm/proc-v6.S b/arch/arm/mm/proc-v6.S
index 7b1843befb9..eb42e5b9486 100644
--- a/arch/arm/mm/proc-v6.S
+++ b/arch/arm/mm/proc-v6.S
@@ -14,10 +14,13 @@
 #include <asm/assembler.h>
 #include <asm/asm-offsets.h>
 #include <asm/elf.h>
-#include <asm/hardware/arm_scu.h>
 #include <asm/pgtable-hwdef.h>
 #include <asm/pgtable.h>
 
+#ifdef CONFIG_SMP
+#include <asm/hardware/arm_scu.h>
+#endif
+
 #include "proc-macros.S"
 
 #define D_CACHE_LINE_SIZE	32
@@ -30,6 +33,12 @@
 #define TTB_RGN_WT	(2 << 3)
 #define TTB_RGN_WB	(3 << 3)
 
+#ifndef CONFIG_SMP
+#define TTB_FLAGS	TTB_RGN_WBWA
+#else
+#define TTB_FLAGS	TTB_RGN_WBWA|TTB_S
+#endif
+
 ENTRY(cpu_v6_proc_init)
 	mov	pc, lr
 
@@ -92,9 +101,7 @@ ENTRY(cpu_v6_switch_mm)
 #ifdef CONFIG_MMU
 	mov	r2, #0
 	ldr	r1, [r1, #MM_CONTEXT_ID]	@ get mm->context.id
-#ifdef CONFIG_SMP
-	orr	r0, r0, #TTB_RGN_WBWA|TTB_S	@ mark PTWs shared, outer cacheable
-#endif
+	orr	r0, r0, #TTB_FLAGS
 	mcr	p15, 0, r2, c7, c5, 6		@ flush BTAC/BTB
 	mcr	p15, 0, r2, c7, c10, 4		@ drain write buffer
 	mcr	p15, 0, r0, c2, c0, 0		@ set TTB 0
@@ -183,8 +190,7 @@ __v6_setup:
 	/* Set up the SCU on core 0 only */
 	mrc	p15, 0, r0, c0, c0, 5		@ CPU core number
 	ands	r0, r0, #15
-	moveq	r0, #0x10000000 @ SCU_BASE
-	orreq	r0, r0, #0x00100000
+	ldreq	r0, =SCU_BASE
 	ldreq	r5, [r0, #SCU_CTRL]
 	orreq	r5, r5, #1
 	streq	r5, [r0, #SCU_CTRL]
@@ -204,9 +210,7 @@ __v6_setup:
 #ifdef CONFIG_MMU
 	mcr	p15, 0, r0, c8, c7, 0		@ invalidate I + D TLBs
 	mcr	p15, 0, r0, c2, c0, 2		@ TTB control register
-#ifdef CONFIG_SMP
-	orr	r4, r4, #TTB_RGN_WBWA|TTB_S	@ mark PTWs shared, outer cacheable
-#endif
+	orr	r4, r4, #TTB_FLAGS
 	mcr	p15, 0, r4, c2, c0, 1		@ load TTB1
 #endif /* CONFIG_MMU */
 	adr	r5, v6_crval
diff --git a/arch/arm/mm/proc-xsc3.S b/arch/arm/mm/proc-xsc3.S
index 94a58455f34..d95921a2ab9 100644
--- a/arch/arm/mm/proc-xsc3.S
+++ b/arch/arm/mm/proc-xsc3.S
@@ -5,23 +5,23 @@
  * Current Maintainer: Lennert Buytenhek <buytenh@wantstofly.org>
  *
  * Copyright 2004 (C) Intel Corp.
- * Copyright 2005 (c) MontaVista Software, Inc.
+ * Copyright 2005 (C) MontaVista Software, Inc.
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  *
- * MMU functions for the Intel XScale3 Core (XSC3).  The XSC3 core is an
- * extension to Intel's original XScale core that adds the following
+ * MMU functions for the Intel XScale3 Core (XSC3).  The XSC3 core is
+ * an extension to Intel's original XScale core that adds the following
  * features:
  *
  * - ARMv6 Supersections
  * - Low Locality Reference pages (replaces mini-cache)
  * - 36-bit addressing
  * - L2 cache
- * - Cache-coherency if chipset supports it
+ * - Cache coherency if chipset supports it
  *
- * Based on orignal XScale code by Nicolas Pitre
+ * Based on original XScale code by Nicolas Pitre.
  */
 
 #include <linux/linkage.h>
@@ -42,12 +42,12 @@
 #define MAX_AREA_SIZE	32768
 
 /*
- * The cache line size of the I and D cache.
+ * The cache line size of the L1 I, L1 D and unified L2 cache.
  */
 #define CACHELINESIZE	32
 
 /*
- * The size of the data cache.
+ * The size of the L1 D cache.
  */
 #define CACHESIZE	32768
 
@@ -57,9 +57,9 @@
 #define L2_CACHE_ENABLE	1
 
 /*
- * This macro is used to wait for a CP15 write and is needed
- * when we have to ensure that the last operation to the co-pro
- * was completed before continuing with operation.
+ * This macro is used to wait for a CP15 write and is needed when we
+ * have to ensure that the last operation to the coprocessor was
+ * completed before continuing with operation.
  */
 	.macro	cpwait_ret, lr, rd
 	mrc	p15, 0, \rd, c2, c0, 0		@ arbitrary read of cp15
@@ -68,13 +68,13 @@
 	.endm
 
 /*
- * This macro cleans & invalidates the entire xsc3 dcache by set & way.
+ * This macro cleans and invalidates the entire L1 D cache.
  */
 
  	.macro  clean_d_cache rd, rs
 	mov	\rd, #0x1f00
 	orr	\rd, \rd, #0x00e0
-1:	mcr	p15, 0, \rd, c7, c14, 2		@ clean/inv set/way
+1:	mcr	p15, 0, \rd, c7, c14, 2		@ clean/invalidate L1 D line
 	adds	\rd, \rd, #0x40000000
 	bcc	1b
 	subs	\rd, \rd, #0x20
@@ -119,15 +119,15 @@ ENTRY(cpu_xsc3_reset)
 	mov	r1, #PSR_F_BIT|PSR_I_BIT|SVC_MODE
 	msr	cpsr_c, r1			@ reset CPSR
 	mrc	p15, 0, r1, c1, c0, 0		@ ctrl register
-	bic	r1, r1, #0x0086			@ ........B....CA.
 	bic	r1, r1, #0x3900			@ ..VIZ..S........
+	bic	r1, r1, #0x0086			@ ........B....CA.
 	mcr	p15, 0, r1, c1, c0, 0		@ ctrl register
-	mcr	p15, 0, ip, c7, c7, 0		@ invalidate I,D caches & BTB
+	mcr	p15, 0, ip, c7, c7, 0		@ invalidate L1 caches and BTB
 	bic	r1, r1, #0x0001			@ ...............M
 	mcr	p15, 0, r1, c1, c0, 0		@ ctrl register
 	@ CAUTION: MMU turned off from this point.  We count on the pipeline
 	@ already containing those two last instructions to survive.
-	mcr	p15, 0, ip, c8, c7, 0		@ invalidate I & D TLBs
+	mcr	p15, 0, ip, c8, c7, 0		@ invalidate I and D TLBs
 	mov	pc, r0
 
 /*
@@ -139,14 +139,12 @@ ENTRY(cpu_xsc3_reset)
  *
  * XScale supports clock switching, but using idle mode support
  * allows external hardware to react to system state changes.
-
- MMG: Come back to this one.
  */
 	.align	5
 
 ENTRY(cpu_xsc3_do_idle)
 	mov	r0, #1
-	mcr	p14, 0, r0, c7, c0, 0		@ Go to IDLE
+	mcr	p14, 0, r0, c7, c0, 0		@ go to idle
 	mov	pc, lr
 
 /* ================================= CACHE ================================ */
@@ -171,9 +169,9 @@ ENTRY(xsc3_flush_kern_cache_all)
 __flush_whole_cache:
 	clean_d_cache r0, r1
 	tst	r2, #VM_EXEC
-	mcrne	p15, 0, ip, c7, c5, 0		@ Invalidate I cache & BTB
-	mcrne	p15, 0, ip, c7, c10, 4		@ Drain Write Buffer
-	mcrne	p15, 0, ip, c7, c5, 4		@ Prefetch Flush
+	mcrne	p15, 0, ip, c7, c5, 0		@ invalidate L1 I cache and BTB
+	mcrne	p15, 0, ip, c7, c10, 4		@ data write barrier
+	mcrne	p15, 0, ip, c7, c5, 4		@ prefetch flush
 	mov	pc, lr
 
 /*
@@ -194,21 +192,21 @@ ENTRY(xsc3_flush_user_cache_range)
 	bhs	__flush_whole_cache
 
 1:	tst	r2, #VM_EXEC
-	mcrne	p15, 0, r0, c7, c5, 1		@ Invalidate I cache line
-	mcr	p15, 0, r0, c7, c14, 1		@ Clean/invalidate D cache line
+	mcrne	p15, 0, r0, c7, c5, 1		@ invalidate L1 I line
+	mcr	p15, 0, r0, c7, c14, 1		@ clean/invalidate L1 D line
 	add	r0, r0, #CACHELINESIZE
 	cmp	r0, r1
 	blo	1b
 	tst	r2, #VM_EXEC
-	mcrne	p15, 0, ip, c7, c5, 6		@ Invalidate BTB
-	mcrne	p15, 0, ip, c7, c10, 4		@ Drain Write Buffer
-	mcrne	p15, 0, ip, c7, c5, 4		@ Prefetch Flush
+	mcrne	p15, 0, ip, c7, c5, 6		@ invalidate BTB
+	mcrne	p15, 0, ip, c7, c10, 4		@ data write barrier
+	mcrne	p15, 0, ip, c7, c5, 4		@ prefetch flush
 	mov	pc, lr
 
 /*
  *	coherent_kern_range(start, end)
  *
- *	Ensure coherency between the Icache and the Dcache in the
+ *	Ensure coherency between the I cache and the D cache in the
  *	region described by start.  If you have non-snooping
  *	Harvard caches, you need to implement this function.
  *
@@ -222,34 +220,34 @@ ENTRY(xsc3_coherent_kern_range)
 /* FALLTHROUGH */
 ENTRY(xsc3_coherent_user_range)
 	bic	r0, r0, #CACHELINESIZE - 1
-1:	mcr	p15, 0, r0, c7, c10, 1		@ clean D entry
+1:	mcr	p15, 0, r0, c7, c10, 1		@ clean L1 D line
 	add	r0, r0, #CACHELINESIZE
 	cmp	r0, r1
 	blo	1b
 	mov	r0, #0
-	mcr	p15, 0, r0, c7, c5, 0		@ Invalidate I cache & BTB
-	mcr	p15, 0, r0, c7, c10, 4		@ Drain Write Buffer
-	mcr	p15, 0, r0, c7, c5, 4		@ Prefetch Flush
+	mcr	p15, 0, r0, c7, c5, 0		@ invalidate L1 I cache and BTB
+	mcr	p15, 0, r0, c7, c10, 4		@ data write barrier
+	mcr	p15, 0, r0, c7, c5, 4		@ prefetch flush
 	mov	pc, lr
 
 /*
  *	flush_kern_dcache_page(void *page)
  *
  *	Ensure no D cache aliasing occurs, either with itself or
- *	the I cache
+ *	the I cache.
  *
  *	- addr	- page aligned address
  */
 ENTRY(xsc3_flush_kern_dcache_page)
 	add	r1, r0, #PAGE_SZ
-1:	mcr	p15, 0, r0, c7, c14, 1		@ Clean/Invalidate D Cache line
+1:	mcr	p15, 0, r0, c7, c14, 1		@ clean/invalidate L1 D line
 	add	r0, r0, #CACHELINESIZE
 	cmp	r0, r1
 	blo	1b
 	mov	r0, #0
-	mcr	p15, 0, r0, c7, c5, 0		@ Invalidate I cache & BTB
-	mcr	p15, 0, r0, c7, c10, 4		@ Drain Write Buffer
-	mcr	p15, 0, r0, c7, c5, 4		@ Prefetch Flush
+	mcr	p15, 0, r0, c7, c5, 0		@ invalidate L1 I cache and BTB
+	mcr	p15, 0, r0, c7, c10, 4		@ data write barrier
+	mcr	p15, 0, r0, c7, c5, 4		@ prefetch flush
 	mov	pc, lr
 
 /*
@@ -266,17 +264,17 @@ ENTRY(xsc3_flush_kern_dcache_page)
 ENTRY(xsc3_dma_inv_range)
 	tst	r0, #CACHELINESIZE - 1
 	bic	r0, r0, #CACHELINESIZE - 1
-	mcrne	p15, 0, r0, c7, c10, 1		@ clean L1 D entry
-	mcrne	p15, 1, r0, c7, c11, 1		@ clean L2 D entry
+	mcrne	p15, 0, r0, c7, c10, 1		@ clean L1 D line
+	mcrne	p15, 1, r0, c7, c11, 1		@ clean L2 line
 	tst	r1, #CACHELINESIZE - 1
-	mcrne	p15, 0, r1, c7, c10, 1		@ clean L1 D entry
-	mcrne	p15, 1, r1, c7, c11, 1		@ clean L2 D entry
-1:	mcr	p15, 0, r0, c7, c6, 1		@ invalidate L1 D entry
-	mcr	p15, 1, r0, c7, c7, 1		@ Invalidate L2 D cache line
+	mcrne	p15, 0, r1, c7, c10, 1		@ clean L1 D line
+	mcrne	p15, 1, r1, c7, c11, 1		@ clean L2 line
+1:	mcr	p15, 0, r0, c7, c6, 1		@ invalidate L1 D line
+	mcr	p15, 1, r0, c7, c7, 1		@ invalidate L2 line
 	add	r0, r0, #CACHELINESIZE
 	cmp	r0, r1
 	blo	1b
-	mcr	p15, 0, r0, c7, c10, 4		@ Drain Write Buffer
+	mcr	p15, 0, r0, c7, c10, 4		@ data write barrier
 	mov	pc, lr
 
 /*
@@ -289,12 +287,12 @@ ENTRY(xsc3_dma_inv_range)
  */
 ENTRY(xsc3_dma_clean_range)
 	bic	r0, r0, #CACHELINESIZE - 1
-1:	mcr	p15, 0, r0, c7, c10, 1		@ clean L1 D entry
-	mcr	p15, 1, r0, c7, c11, 1		@ clean L2 D entry
+1:	mcr	p15, 0, r0, c7, c10, 1		@ clean L1 D line
+	mcr	p15, 1, r0, c7, c11, 1		@ clean L2 line
 	add	r0, r0, #CACHELINESIZE
 	cmp	r0, r1
 	blo	1b
-	mcr	p15, 0, r0, c7, c10, 4		@ Drain Write Buffer
+	mcr	p15, 0, r0, c7, c10, 4		@ data write barrier
 	mov	pc, lr
 
 /*
@@ -307,13 +305,13 @@ ENTRY(xsc3_dma_clean_range)
  */
 ENTRY(xsc3_dma_flush_range)
 	bic	r0, r0, #CACHELINESIZE - 1
-1:	mcr	p15, 0, r0, c7, c14, 1	@ Clean/invalidate L1 D cache line
-	mcr	p15, 1, r0, c7, c11, 1	@ Clean L2 D cache line
-	mcr	p15, 1, r0, c7, c7, 1	@ Invalidate L2 D cache line
+1:	mcr	p15, 0, r0, c7, c14, 1		@ clean/invalidate L1 D line
+	mcr	p15, 1, r0, c7, c11, 1		@ clean L2 line
+	mcr	p15, 1, r0, c7, c7, 1		@ invalidate L2 line
 	add	r0, r0, #CACHELINESIZE
 	cmp	r0, r1
 	blo	1b
-	mcr	p15, 0, r0, c7, c10, 4		@ Drain Write Buffer
+	mcr	p15, 0, r0, c7, c10, 4		@ data write barrier
 	mov	pc, lr
 
 ENTRY(xsc3_cache_fns)
@@ -328,7 +326,7 @@ ENTRY(xsc3_cache_fns)
 	.long	xsc3_dma_flush_range
 
 ENTRY(cpu_xsc3_dcache_clean_area)
-1:	mcr	p15, 0, r0, c7, c10, 1		@ clean D entry
+1:	mcr	p15, 0, r0, c7, c10, 1		@ clean L1 D line
 	add	r0, r0, #CACHELINESIZE
 	subs	r1, r1, #CACHELINESIZE
 	bhi	1b
@@ -346,14 +344,14 @@ ENTRY(cpu_xsc3_dcache_clean_area)
 	.align	5
 ENTRY(cpu_xsc3_switch_mm)
 	clean_d_cache r1, r2
-	mcr	p15, 0, ip, c7, c5, 0		@ Invalidate I cache & BTB
-	mcr	p15, 0, ip, c7, c10, 4		@ Drain Write Buffer
-	mcr	p15, 0, ip, c7, c5, 4		@ Prefetch Flush
+	mcr	p15, 0, ip, c7, c5, 0		@ invalidate L1 I cache and BTB
+	mcr	p15, 0, ip, c7, c10, 4		@ data write barrier
+	mcr	p15, 0, ip, c7, c5, 4		@ prefetch flush
 #ifdef L2_CACHE_ENABLE
 	orr	r0, r0, #0x18			@ cache the page table in L2
 #endif
 	mcr	p15, 0, r0, c2, c0, 0		@ load page table pointer
-	mcr	p15, 0, ip, c8, c7, 0		@ invalidate I & D TLBs
+	mcr	p15, 0, ip, c8, c7, 0		@ invalidate I and D TLBs
 	cpwait_ret lr, ip
 
 /*
@@ -366,34 +364,34 @@ ENTRY(cpu_xsc3_switch_mm)
 ENTRY(cpu_xsc3_set_pte_ext)
 	str	r1, [r0], #-2048		@ linux version
 
-	bic	r2, r1, #0xff0			@ Keep C, B bits
+	bic	r2, r1, #0xff0			@ keep C, B bits
 	orr	r2, r2, #PTE_TYPE_EXT		@ extended page
-	tst	r1, #L_PTE_SHARED		@ Shared?
+	tst	r1, #L_PTE_SHARED		@ shared?
 	orrne	r2, r2, #0x200
 
 	eor	r3, r1, #L_PTE_PRESENT | L_PTE_YOUNG | L_PTE_WRITE | L_PTE_DIRTY
 
-	tst	r3, #L_PTE_USER			@ User?
+	tst	r3, #L_PTE_USER			@ user?
 	orrne	r2, r2, #PTE_EXT_AP_URO_SRW	@ yes -> user r/o, system r/w
 
-	tst	r3, #L_PTE_WRITE | L_PTE_DIRTY	@ Write and Dirty?
+	tst	r3, #L_PTE_WRITE | L_PTE_DIRTY	@ write and dirty?
 	orreq	r2, r2, #PTE_EXT_AP_UNO_SRW	@ yes -> user n/a, system r/w
 						@ combined with user -> user r/w
 
 #if L2_CACHE_ENABLE
-	@ If its cacheable it needs to be in L2 also.
+	@ If it's cacheable, it needs to be in L2 also.
 	eor	ip, r1, #L_PTE_CACHEABLE
 	tst	ip, #L_PTE_CACHEABLE
 	orreq	r2, r2, #PTE_EXT_TEX(0x5)
 #endif
 
-	tst	r3, #L_PTE_PRESENT | L_PTE_YOUNG	@ Present and Young?
+	tst	r3, #L_PTE_PRESENT | L_PTE_YOUNG	@ present and young?
 	movne	r2, #0				@ no -> fault
 
 	str	r2, [r0]			@ hardware version
 	mov	ip, #0
-	mcr	p15, 0, r0, c7, c10, 1		@ Clean D cache line mcr
-	mcr	p15, 0, ip, c7, c10, 4		@ Drain Write Buffer
+	mcr	p15, 0, r0, c7, c10, 1		@ clean L1 D line
+	mcr	p15, 0, ip, c7, c10, 4		@ data write barrier
 	mov	pc, lr
 
 	.ltorg
@@ -406,17 +404,18 @@ ENTRY(cpu_xsc3_set_pte_ext)
 __xsc3_setup:
 	mov	r0, #PSR_F_BIT|PSR_I_BIT|SVC_MODE
 	msr	cpsr_c, r0
-	mcr	p15, 0, ip, c7, c7, 0		@ invalidate I, D caches & BTB
-	mcr	p15, 0, ip, c7, c10, 4		@ Drain Write Buffer
-	mcr	p15, 0, ip, c7, c5, 4		@ Prefetch Flush
-	mcr	p15, 0, ip, c8, c7, 0		@ invalidate I, D TLBs
+	mcr	p15, 0, ip, c7, c7, 0		@ invalidate L1 caches and BTB
+	mcr	p15, 0, ip, c7, c10, 4		@ data write barrier
+	mcr	p15, 0, ip, c7, c5, 4		@ prefetch flush
+	mcr	p15, 0, ip, c8, c7, 0		@ invalidate I and D TLBs
 #if L2_CACHE_ENABLE
 	orr	r4, r4, #0x18			@ cache the page table in L2
 #endif
 	mcr	p15, 0, r4, c2, c0, 0		@ load page table pointer
-	mov	r0, #1				@ Allow access to CP0 and CP13
-	orr	r0, r0, #1 << 13		@ Its undefined whether this
-	mcr	p15, 0, r0, c15, c1, 0		@ affects USR or SVC modes
+
+	mov	r0, #0				@ don't allow CP access
+	mcr	p15, 0, r0, c15, c1, 0		@ write CP access register
+
 	mrc	p15, 0, r0, c1, c0, 1		@ get auxiliary control reg
 	and	r0, r0, #2			@ preserve bit P bit setting
 #if L2_CACHE_ENABLE
@@ -427,9 +426,9 @@ __xsc3_setup:
 	adr	r5, xsc3_crval
 	ldmia	r5, {r5, r6}
 	mrc	p15, 0, r0, c1, c0, 0		@ get control register
-	bic	r0, r0, r5			@ .... .... .... ..A.
-	orr	r0, r0, r6			@ .... .... .... .C.M
-	orr	r0, r0, #0x00000800		@ ..VI Z..S .... ....
+	bic	r0, r0, r5			@ ..V. ..R. .... ..A.
+	orr	r0, r0, r6			@ ..VI Z..S .... .C.M (mmu)
+						@ ...I Z..S .... .... (uc)
 #if L2_CACHE_ENABLE
 	orr 	r0, r0, #0x04000000		@ L2 enable
 #endif
@@ -439,7 +438,7 @@ __xsc3_setup:
 
 	.type	xsc3_crval, #object
 xsc3_crval:
-	crval	clear=0x04003b02, mmuset=0x00003105, ucset=0x00001100
+	crval	clear=0x04002202, mmuset=0x00003905, ucset=0x00001900
 
 	__INITDATA
 
@@ -474,7 +473,7 @@ cpu_elf_name:
 
 	.type	cpu_xsc3_name, #object
 cpu_xsc3_name:
-	.asciz	"XScale-Core3"
+	.asciz	"XScale-V3 based processor"
 	.size	cpu_xsc3_name, . - cpu_xsc3_name
 
 	.align
@@ -490,7 +489,7 @@ __xsc3_proc_info:
 		PMD_SECT_CACHEABLE | \
 		PMD_SECT_AP_WRITE | \
 		PMD_SECT_AP_READ
-	.long   PMD_TYPE_SECT | \
+	.long	PMD_TYPE_SECT | \
 		PMD_SECT_AP_WRITE | \
 		PMD_SECT_AP_READ
 	b	__xsc3_setup
diff --git a/arch/arm/mm/tlb-v6.S b/arch/arm/mm/tlb-v6.S
index fd6adde3909..20f84bbaa9b 100644
--- a/arch/arm/mm/tlb-v6.S
+++ b/arch/arm/mm/tlb-v6.S
@@ -53,6 +53,8 @@ ENTRY(v6wbi_flush_user_tlb_range)
 	add	r0, r0, #PAGE_SZ
 	cmp	r0, r1
 	blo	1b
+	mcr	p15, 0, ip, c7, c5, 6		@ flush BTAC/BTB
+	mcr	p15, 0, ip, c7, c10, 4		@ data synchronization barrier
 	mov	pc, lr
 
 /*
@@ -80,7 +82,9 @@ ENTRY(v6wbi_flush_kern_tlb_range)
 	add	r0, r0, #PAGE_SZ
 	cmp	r0, r1
 	blo	1b
+	mcr	p15, 0, r2, c7, c5, 6		@ flush BTAC/BTB
 	mcr	p15, 0, r2, c7, c10, 4		@ data synchronization barrier
+	mcr	p15, 0, r2, c7, c5, 4		@ prefetch flush
 	mov	pc, lr
 
 	.section ".text.init", #alloc, #execinstr
diff --git a/arch/arm/plat-s3c24xx/Kconfig b/arch/arm/plat-s3c24xx/Kconfig
new file mode 100644
index 00000000000..e2234316063
--- /dev/null
+++ b/arch/arm/plat-s3c24xx/Kconfig
@@ -0,0 +1,99 @@
+# arch/arm/plat-s3c24xx/Kconfig
+#
+# Copyright 2007 Simtec Electronics
+#
+# Licensed under GPLv2
+
+config PLAT_S3C24XX
+	bool
+	depends on ARCH_S3C2410
+	default y if ARCH_S3C2410
+	help
+	  Base platform code for any Samsung S3C device
+
+if PLAT_S3C24XX
+
+config CPU_S3C244X
+	bool
+	depends on ARCH_S3C2410 && (CPU_S3C2440 || CPU_S3C2442)
+	help
+	  Support for S3C2440 and S3C2442 Samsung Mobile CPU based systems.
+
+config PM_SIMTEC
+	bool
+	help
+	  Common power management code for systems that are
+	  compatible with the Simtec style of power management
+
+config S3C2410_BOOT_WATCHDOG
+	bool "S3C2410 Initialisation watchdog"
+	depends on ARCH_S3C2410 && S3C2410_WATCHDOG
+	help
+	  Say y to enable the watchdog during the kernel decompression
+	  stage. If the kernel fails to uncompress, then the watchdog
+	  will trigger a reset and the system should restart.
+
+config S3C2410_BOOT_ERROR_RESET
+	bool "S3C2410 Reboot on decompression error"
+	depends on ARCH_S3C2410
+	help
+	  Say y here to use the watchdog to reset the system if the
+	  kernel decompressor detects an error during decompression.
+
+config S3C2410_PM_DEBUG
+	bool "S3C2410 PM Suspend debug"
+	depends on ARCH_S3C2410 && PM
+	help
+	  Say Y here if you want verbose debugging from the PM Suspend and
+	  Resume code. See <file:Documentation/arm/Samsung-S3C24XX/Suspend.txt>
+	  for more information.
+
+config S3C2410_PM_CHECK
+	bool "S3C2410 PM Suspend Memory CRC"
+	depends on ARCH_S3C2410 && PM && CRC32
+	help
+ 	  Enable the PM code's memory area checksum over sleep. This option
+	  will generate CRCs of all blocks of memory, and store them before
+	  going to sleep. The blocks are then checked on resume for any
+	  errors.
+
+config S3C2410_PM_CHECK_CHUNKSIZE
+	int "S3C2410 PM Suspend CRC Chunksize (KiB)"
+	depends on ARCH_S3C2410 && PM && S3C2410_PM_CHECK
+	default 64
+	help
+	  Set the chunksize in Kilobytes of the CRC for checking memory
+	  corruption over suspend and resume. A smaller value will mean that
+	  the CRC data block will take more memory, but wil identify any
+	  faults with better precision.
+
+config S3C2410_LOWLEVEL_UART_PORT
+	int "S3C2410 UART to use for low-level messages"
+	default 0
+	help
+	  Choice of which UART port to use for the low-level messages,
+	  such as the `Uncompressing...` at start time. The value of
+	  this configuration should be between zero and two. The port
+	  must have been initialised by the boot-loader before use.
+
+config S3C2410_DMA
+	bool "S3C2410 DMA support"
+	depends on ARCH_S3C2410
+	help
+	  S3C2410 DMA support. This is needed for drivers like sound which
+	  use the S3C2410's DMA system to move data to and from the
+	  peripheral blocks.
+
+config S3C2410_DMA_DEBUG
+	bool "S3C2410 DMA support debug"
+	depends on ARCH_S3C2410 && S3C2410_DMA
+	help
+	  Enable debugging output for the DMA code. This option sends info
+	  to the kernel log, at priority KERN_DEBUG.
+
+config MACH_SMDK
+	bool
+	help
+	  Common machine code for SMDK2410 and SMDK2440
+
+endif
diff --git a/arch/arm/plat-s3c24xx/Makefile b/arch/arm/plat-s3c24xx/Makefile
new file mode 100644
index 00000000000..8e5ccaa1f03
--- /dev/null
+++ b/arch/arm/plat-s3c24xx/Makefile
@@ -0,0 +1,30 @@
+# arch/arm/plat-s3c24xx/Makefile
+#
+# Copyright 2007 Simtec Electronics
+#
+# Licensed under GPLv2
+
+obj-y				:=
+obj-m				:=
+obj-n				:=
+obj-				:=
+
+
+# Core files
+
+obj-y				+= cpu.o
+obj-y				+= irq.o
+obj-y				+= devs.o
+obj-y				+= gpio.o
+obj-y				+= time.o
+obj-y				+= clock.o
+
+# Architecture dependant builds
+
+obj-$(CONFIG_CPU_S3C244X)	+= s3c244x.o
+obj-$(CONFIG_CPU_S3C244X)	+= s3c244x-irq.o
+obj-$(CONFIG_PM_SIMTEC)		+= pm-simtec.o
+obj-$(CONFIG_PM)		+= pm.o
+obj-$(CONFIG_PM)		+= sleep.o
+obj-$(CONFIG_S3C2410_DMA)	+= dma.o
+obj-$(CONFIG_MACH_SMDK)		+= common-smdk.o
diff --git a/arch/arm/plat-s3c24xx/clock.c b/arch/arm/plat-s3c24xx/clock.c
new file mode 100644
index 00000000000..d3dc03a7383
--- /dev/null
+++ b/arch/arm/plat-s3c24xx/clock.c
@@ -0,0 +1,449 @@
+/* linux/arch/arm/plat-s3c24xx/clock.c
+ *
+ * Copyright (c) 2004-2005 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C24XX Core clock control support
+ *
+ * Based on, and code from linux/arch/arm/mach-versatile/clock.c
+ **
+ **  Copyright (C) 2004 ARM Limited.
+ **  Written by Deep Blue Solutions Limited.
+ *
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+*/
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/list.h>
+#include <linux/errno.h>
+#include <linux/err.h>
+#include <linux/platform_device.h>
+#include <linux/sysdev.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/clk.h>
+#include <linux/mutex.h>
+#include <linux/delay.h>
+
+#include <asm/hardware.h>
+#include <asm/irq.h>
+#include <asm/io.h>
+
+#include <asm/arch/regs-clock.h>
+#include <asm/arch/regs-gpio.h>
+
+#include <asm/plat-s3c24xx/clock.h>
+#include <asm/plat-s3c24xx/cpu.h>
+
+/* clock information */
+
+static LIST_HEAD(clocks);
+
+DEFINE_MUTEX(clocks_mutex);
+
+/* enable and disable calls for use with the clk struct */
+
+static int clk_null_enable(struct clk *clk, int enable)
+{
+	return 0;
+}
+
+/* Clock API calls */
+
+struct clk *clk_get(struct device *dev, const char *id)
+{
+	struct clk *p;
+	struct clk *clk = ERR_PTR(-ENOENT);
+	int idno;
+
+	if (dev == NULL || dev->bus != &platform_bus_type)
+		idno = -1;
+	else
+		idno = to_platform_device(dev)->id;
+
+	mutex_lock(&clocks_mutex);
+
+	list_for_each_entry(p, &clocks, list) {
+		if (p->id == idno &&
+		    strcmp(id, p->name) == 0 &&
+		    try_module_get(p->owner)) {
+			clk = p;
+			break;
+		}
+	}
+
+	/* check for the case where a device was supplied, but the
+	 * clock that was being searched for is not device specific */
+
+	if (IS_ERR(clk)) {
+		list_for_each_entry(p, &clocks, list) {
+			if (p->id == -1 && strcmp(id, p->name) == 0 &&
+			    try_module_get(p->owner)) {
+				clk = p;
+				break;
+			}
+		}
+	}
+
+	mutex_unlock(&clocks_mutex);
+	return clk;
+}
+
+void clk_put(struct clk *clk)
+{
+	module_put(clk->owner);
+}
+
+int clk_enable(struct clk *clk)
+{
+	if (IS_ERR(clk) || clk == NULL)
+		return -EINVAL;
+
+	clk_enable(clk->parent);
+
+	mutex_lock(&clocks_mutex);
+
+	if ((clk->usage++) == 0)
+		(clk->enable)(clk, 1);
+
+	mutex_unlock(&clocks_mutex);
+	return 0;
+}
+
+void clk_disable(struct clk *clk)
+{
+	if (IS_ERR(clk) || clk == NULL)
+		return;
+
+	mutex_lock(&clocks_mutex);
+
+	if ((--clk->usage) == 0)
+		(clk->enable)(clk, 0);
+
+	mutex_unlock(&clocks_mutex);
+	clk_disable(clk->parent);
+}
+
+
+unsigned long clk_get_rate(struct clk *clk)
+{
+	if (IS_ERR(clk))
+		return 0;
+
+	if (clk->rate != 0)
+		return clk->rate;
+
+	if (clk->get_rate != NULL)
+		return (clk->get_rate)(clk);
+
+	if (clk->parent != NULL)
+		return clk_get_rate(clk->parent);
+
+	return clk->rate;
+}
+
+long clk_round_rate(struct clk *clk, unsigned long rate)
+{
+	if (!IS_ERR(clk) && clk->round_rate)
+		return (clk->round_rate)(clk, rate);
+
+	return rate;
+}
+
+int clk_set_rate(struct clk *clk, unsigned long rate)
+{
+	int ret;
+
+	if (IS_ERR(clk))
+		return -EINVAL;
+
+	mutex_lock(&clocks_mutex);
+	ret = (clk->set_rate)(clk, rate);
+	mutex_unlock(&clocks_mutex);
+
+	return ret;
+}
+
+struct clk *clk_get_parent(struct clk *clk)
+{
+	return clk->parent;
+}
+
+int clk_set_parent(struct clk *clk, struct clk *parent)
+{
+	int ret = 0;
+
+	if (IS_ERR(clk))
+		return -EINVAL;
+
+	mutex_lock(&clocks_mutex);
+
+	if (clk->set_parent)
+		ret = (clk->set_parent)(clk, parent);
+
+	mutex_unlock(&clocks_mutex);
+
+	return ret;
+}
+
+EXPORT_SYMBOL(clk_get);
+EXPORT_SYMBOL(clk_put);
+EXPORT_SYMBOL(clk_enable);
+EXPORT_SYMBOL(clk_disable);
+EXPORT_SYMBOL(clk_get_rate);
+EXPORT_SYMBOL(clk_round_rate);
+EXPORT_SYMBOL(clk_set_rate);
+EXPORT_SYMBOL(clk_get_parent);
+EXPORT_SYMBOL(clk_set_parent);
+
+/* base clocks */
+
+struct clk clk_xtal = {
+	.name		= "xtal",
+	.id		= -1,
+	.rate		= 0,
+	.parent		= NULL,
+	.ctrlbit	= 0,
+};
+
+struct clk clk_mpll = {
+	.name		= "mpll",
+	.id		= -1,
+};
+
+struct clk clk_upll = {
+	.name		= "upll",
+	.id		= -1,
+	.parent		= NULL,
+	.ctrlbit	= 0,
+};
+
+struct clk clk_f = {
+	.name		= "fclk",
+	.id		= -1,
+	.rate		= 0,
+	.parent		= &clk_mpll,
+	.ctrlbit	= 0,
+};
+
+struct clk clk_h = {
+	.name		= "hclk",
+	.id		= -1,
+	.rate		= 0,
+	.parent		= NULL,
+	.ctrlbit	= 0,
+};
+
+struct clk clk_p = {
+	.name		= "pclk",
+	.id		= -1,
+	.rate		= 0,
+	.parent		= NULL,
+	.ctrlbit	= 0,
+};
+
+struct clk clk_usb_bus = {
+	.name		= "usb-bus",
+	.id		= -1,
+	.rate		= 0,
+	.parent		= &clk_upll,
+};
+
+/* clocks that could be registered by external code */
+
+static int s3c24xx_dclk_enable(struct clk *clk, int enable)
+{
+	unsigned long dclkcon = __raw_readl(S3C24XX_DCLKCON);
+
+	if (enable)
+		dclkcon |= clk->ctrlbit;
+	else
+		dclkcon &= ~clk->ctrlbit;
+
+	__raw_writel(dclkcon, S3C24XX_DCLKCON);
+
+	return 0;
+}
+
+static int s3c24xx_dclk_setparent(struct clk *clk, struct clk *parent)
+{
+	unsigned long dclkcon;
+	unsigned int uclk;
+
+	if (parent == &clk_upll)
+		uclk = 1;
+	else if (parent == &clk_p)
+		uclk = 0;
+	else
+		return -EINVAL;
+
+	clk->parent = parent;
+
+	dclkcon = __raw_readl(S3C24XX_DCLKCON);
+
+	if (clk->ctrlbit == S3C2410_DCLKCON_DCLK0EN) {
+		if (uclk)
+			dclkcon |= S3C2410_DCLKCON_DCLK0_UCLK;
+		else
+			dclkcon &= ~S3C2410_DCLKCON_DCLK0_UCLK;
+	} else {
+		if (uclk)
+			dclkcon |= S3C2410_DCLKCON_DCLK1_UCLK;
+		else
+			dclkcon &= ~S3C2410_DCLKCON_DCLK1_UCLK;
+	}
+
+	__raw_writel(dclkcon, S3C24XX_DCLKCON);
+
+	return 0;
+}
+
+
+static int s3c24xx_clkout_setparent(struct clk *clk, struct clk *parent)
+{
+	unsigned long mask;
+	unsigned long source;
+
+	/* calculate the MISCCR setting for the clock */
+
+	if (parent == &clk_xtal)
+		source = S3C2410_MISCCR_CLK0_MPLL;
+	else if (parent == &clk_upll)
+		source = S3C2410_MISCCR_CLK0_UPLL;
+	else if (parent == &clk_f)
+		source = S3C2410_MISCCR_CLK0_FCLK;
+	else if (parent == &clk_h)
+		source = S3C2410_MISCCR_CLK0_HCLK;
+	else if (parent == &clk_p)
+		source = S3C2410_MISCCR_CLK0_PCLK;
+	else if (clk == &s3c24xx_clkout0 && parent == &s3c24xx_dclk0)
+		source = S3C2410_MISCCR_CLK0_DCLK0;
+	else if (clk == &s3c24xx_clkout1 && parent == &s3c24xx_dclk1)
+		source = S3C2410_MISCCR_CLK0_DCLK0;
+	else
+		return -EINVAL;
+
+	clk->parent = parent;
+
+	if (clk == &s3c24xx_dclk0)
+		mask = S3C2410_MISCCR_CLK0_MASK;
+	else {
+		source <<= 4;
+		mask = S3C2410_MISCCR_CLK1_MASK;
+	}
+
+	s3c2410_modify_misccr(mask, source);
+	return 0;
+}
+
+/* external clock definitions */
+
+struct clk s3c24xx_dclk0 = {
+	.name		= "dclk0",
+	.id		= -1,
+	.ctrlbit	= S3C2410_DCLKCON_DCLK0EN,
+	.enable	        = s3c24xx_dclk_enable,
+	.set_parent	= s3c24xx_dclk_setparent,
+};
+
+struct clk s3c24xx_dclk1 = {
+	.name		= "dclk1",
+	.id		= -1,
+	.ctrlbit	= S3C2410_DCLKCON_DCLK0EN,
+	.enable		= s3c24xx_dclk_enable,
+	.set_parent	= s3c24xx_dclk_setparent,
+};
+
+struct clk s3c24xx_clkout0 = {
+	.name		= "clkout0",
+	.id		= -1,
+	.set_parent	= s3c24xx_clkout_setparent,
+};
+
+struct clk s3c24xx_clkout1 = {
+	.name		= "clkout1",
+	.id		= -1,
+	.set_parent	= s3c24xx_clkout_setparent,
+};
+
+struct clk s3c24xx_uclk = {
+	.name		= "uclk",
+	.id		= -1,
+};
+
+/* initialise the clock system */
+
+int s3c24xx_register_clock(struct clk *clk)
+{
+	clk->owner = THIS_MODULE;
+
+	if (clk->enable == NULL)
+		clk->enable = clk_null_enable;
+
+	/* add to the list of available clocks */
+
+	mutex_lock(&clocks_mutex);
+	list_add(&clk->list, &clocks);
+	mutex_unlock(&clocks_mutex);
+
+	return 0;
+}
+
+/* initalise all the clocks */
+
+int __init s3c24xx_setup_clocks(unsigned long xtal,
+				unsigned long fclk,
+				unsigned long hclk,
+				unsigned long pclk)
+{
+	printk(KERN_INFO "S3C24XX Clocks, (c) 2004 Simtec Electronics\n");
+
+	/* initialise the main system clocks */
+
+	clk_xtal.rate = xtal;
+	clk_upll.rate = s3c2410_get_pll(__raw_readl(S3C2410_UPLLCON), xtal);
+
+	clk_mpll.rate = fclk;
+	clk_h.rate = hclk;
+	clk_p.rate = pclk;
+	clk_f.rate = fclk;
+
+	/* assume uart clocks are correctly setup */
+
+	/* register our clocks */
+
+	if (s3c24xx_register_clock(&clk_xtal) < 0)
+		printk(KERN_ERR "failed to register master xtal\n");
+
+	if (s3c24xx_register_clock(&clk_mpll) < 0)
+		printk(KERN_ERR "failed to register mpll clock\n");
+
+	if (s3c24xx_register_clock(&clk_upll) < 0)
+		printk(KERN_ERR "failed to register upll clock\n");
+
+	if (s3c24xx_register_clock(&clk_f) < 0)
+		printk(KERN_ERR "failed to register cpu fclk\n");
+
+	if (s3c24xx_register_clock(&clk_h) < 0)
+		printk(KERN_ERR "failed to register cpu hclk\n");
+
+	if (s3c24xx_register_clock(&clk_p) < 0)
+		printk(KERN_ERR "failed to register cpu pclk\n");
+
+	return 0;
+}
diff --git a/arch/arm/mach-s3c2410/common-smdk.c b/arch/arm/plat-s3c24xx/common-smdk.c
index a40eaa65617..908efa7d745 100644
--- a/arch/arm/mach-s3c2410/common-smdk.c
+++ b/arch/arm/plat-s3c24xx/common-smdk.c
@@ -1,4 +1,4 @@
-/* linux/arch/arm/mach-s3c2410/common-smdk.c
+/* linux/arch/arm/plat-s3c24xx/common-smdk.c
  *
  * Copyright (c) 2006 Simtec Electronics
  *	Ben Dooks <ben@simtec.co.uk>
@@ -38,9 +38,9 @@
 
 #include <asm/arch/nand.h>
 
-#include "common-smdk.h"
-#include "devs.h"
-#include "pm.h"
+#include <asm/plat-s3c24xx/common-smdk.h>
+#include <asm/plat-s3c24xx/devs.h>
+#include <asm/plat-s3c24xx/pm.h>
 
 /* LED devices */
 
diff --git a/arch/arm/mach-s3c2410/cpu.c b/arch/arm/plat-s3c24xx/cpu.c
index ae1f5bb63f7..6a2d1070e5a 100644
--- a/arch/arm/mach-s3c2410/cpu.c
+++ b/arch/arm/plat-s3c24xx/cpu.c
@@ -1,4 +1,4 @@
-/* linux/arch/arm/mach-s3c2410/cpu.c
+/* linux/arch/arm/plat-s3c24xx/cpu.c
  *
  * Copyright (c) 2004-2005 Simtec Electronics
  *	http://www.simtec.co.uk/products/SWLINUX/
@@ -40,15 +40,16 @@
 #include <asm/arch/regs-gpio.h>
 #include <asm/arch/regs-serial.h>
 
-#include "cpu.h"
-#include "devs.h"
-#include "clock.h"
-#include "s3c2400.h"
-#include "s3c2410.h"
-#include "s3c2412.h"
+#include <asm/plat-s3c24xx/cpu.h>
+#include <asm/plat-s3c24xx/devs.h>
+#include <asm/plat-s3c24xx/clock.h>
+#include <asm/plat-s3c24xx/s3c2400.h>
+#include <asm/plat-s3c24xx/s3c2410.h>
+#include <asm/plat-s3c24xx/s3c2412.h>
 #include "s3c244x.h"
-#include "s3c2440.h"
-#include "s3c2442.h"
+#include <asm/plat-s3c24xx/s3c2440.h>
+#include <asm/plat-s3c24xx/s3c2442.h>
+#include <asm/plat-s3c24xx/s3c2443.h>
 
 struct cpu_table {
 	unsigned long	idcode;
@@ -67,6 +68,7 @@ static const char name_s3c2410[]  = "S3C2410";
 static const char name_s3c2412[]  = "S3C2412";
 static const char name_s3c2440[]  = "S3C2440";
 static const char name_s3c2442[]  = "S3C2442";
+static const char name_s3c2443[]  = "S3C2443";
 static const char name_s3c2410a[] = "S3C2410A";
 static const char name_s3c2440a[] = "S3C2440A";
 
@@ -135,6 +137,15 @@ static struct cpu_table cpu_ids[] __initdata = {
 		.name		= name_s3c2412,
 	},
 	{
+		.idcode		= 0x32443001,
+		.idmask		= 0xffffffff,
+		.map_io		= s3c2443_map_io,
+		.init_clocks	= s3c2443_init_clocks,
+		.init_uarts	= s3c2443_init_uarts,
+		.init		= s3c2443_init,
+		.name		= name_s3c2443,
+	},
+	{
 		.idcode		= 0x0,   /* S3C2400 doesn't have an idcode */
 		.idmask		= 0xffffffff,
 		.map_io		= s3c2400_map_io,
diff --git a/arch/arm/mach-s3c2410/devs.c b/arch/arm/plat-s3c24xx/devs.c
index faccde2092d..0fe53b39cb2 100644
--- a/arch/arm/mach-s3c2410/devs.c
+++ b/arch/arm/plat-s3c24xx/devs.c
@@ -1,4 +1,4 @@
-/* linux/arch/arm/mach-s3c2410/devs.c
+/* linux/arch/arm/plat-s3c24xx/devs.c
  *
  * Copyright (c) 2004 Simtec Electronics
  *	Ben Dooks <ben@simtec.co.uk>
@@ -29,9 +29,10 @@
 #include <asm/irq.h>
 
 #include <asm/arch/regs-serial.h>
+#include <asm/arch/udc.h>
 
-#include "devs.h"
-#include "cpu.h"
+#include <asm/plat-s3c24xx/devs.h>
+#include <asm/plat-s3c24xx/cpu.h>
 
 /* Serial port registrations */
 
@@ -230,6 +231,20 @@ struct platform_device s3c_device_usbgadget = {
 
 EXPORT_SYMBOL(s3c_device_usbgadget);
 
+void __init s3c24xx_udc_set_platdata(struct s3c2410_udc_mach_info *pd)
+{
+	struct s3c2410_udc_mach_info *npd;
+
+	npd = kmalloc(sizeof(*npd), GFP_KERNEL);
+	if (npd) {
+		memcpy(npd, pd, sizeof(*npd));
+		s3c_device_usbgadget.dev.platform_data = npd;
+	} else {
+		printk(KERN_ERR "no memory for udc platform data\n");
+	}
+}
+
+
 /* Watchdog */
 
 static struct resource s3c_wdt_resource[] = {
diff --git a/arch/arm/plat-s3c24xx/dma.c b/arch/arm/plat-s3c24xx/dma.c
new file mode 100644
index 00000000000..4540a806f52
--- /dev/null
+++ b/arch/arm/plat-s3c24xx/dma.c
@@ -0,0 +1,1499 @@
+/* linux/arch/arm/plat-s3c24xx/dma.c
+ *
+ * Copyright (c) 2003-2005,2006 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C2410 DMA core
+ *
+ * http://armlinux.simtec.co.uk/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+
+#ifdef CONFIG_S3C2410_DMA_DEBUG
+#define DEBUG
+#endif
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/sched.h>
+#include <linux/spinlock.h>
+#include <linux/interrupt.h>
+#include <linux/sysdev.h>
+#include <linux/slab.h>
+#include <linux/errno.h>
+#include <linux/delay.h>
+
+#include <asm/system.h>
+#include <asm/irq.h>
+#include <asm/hardware.h>
+#include <asm/io.h>
+#include <asm/dma.h>
+
+#include <asm/mach/dma.h>
+#include <asm/arch/map.h>
+
+#include <asm/plat-s3c24xx/dma.h>
+
+/* io map for dma */
+static void __iomem *dma_base;
+static struct kmem_cache *dma_kmem;
+
+static int dma_channels;
+
+struct s3c24xx_dma_selection dma_sel;
+
+/* dma channel state information */
+struct s3c2410_dma_chan s3c2410_chans[S3C2410_DMA_CHANNELS];
+
+/* debugging functions */
+
+#define BUF_MAGIC (0xcafebabe)
+
+#define dmawarn(fmt...) printk(KERN_DEBUG fmt)
+
+#define dma_regaddr(chan, reg) ((chan)->regs + (reg))
+
+#if 1
+#define dma_wrreg(chan, reg, val) writel((val), (chan)->regs + (reg))
+#else
+static inline void
+dma_wrreg(struct s3c2410_dma_chan *chan, int reg, unsigned long val)
+{
+	pr_debug("writing %08x to register %08x\n",(unsigned int)val,reg);
+	writel(val, dma_regaddr(chan, reg));
+}
+#endif
+
+#define dma_rdreg(chan, reg) readl((chan)->regs + (reg))
+
+/* captured register state for debug */
+
+struct s3c2410_dma_regstate {
+	unsigned long         dcsrc;
+	unsigned long         disrc;
+	unsigned long         dstat;
+	unsigned long         dcon;
+	unsigned long         dmsktrig;
+};
+
+#ifdef CONFIG_S3C2410_DMA_DEBUG
+
+/* dmadbg_showregs
+ *
+ * simple debug routine to print the current state of the dma registers
+*/
+
+static void
+dmadbg_capture(struct s3c2410_dma_chan *chan, struct s3c2410_dma_regstate *regs)
+{
+	regs->dcsrc    = dma_rdreg(chan, S3C2410_DMA_DCSRC);
+	regs->disrc    = dma_rdreg(chan, S3C2410_DMA_DISRC);
+	regs->dstat    = dma_rdreg(chan, S3C2410_DMA_DSTAT);
+	regs->dcon     = dma_rdreg(chan, S3C2410_DMA_DCON);
+	regs->dmsktrig = dma_rdreg(chan, S3C2410_DMA_DMASKTRIG);
+}
+
+static void
+dmadbg_dumpregs(const char *fname, int line, struct s3c2410_dma_chan *chan,
+		 struct s3c2410_dma_regstate *regs)
+{
+	printk(KERN_DEBUG "dma%d: %s:%d: DCSRC=%08lx, DISRC=%08lx, DSTAT=%08lx DMT=%02lx, DCON=%08lx\n",
+	       chan->number, fname, line,
+	       regs->dcsrc, regs->disrc, regs->dstat, regs->dmsktrig,
+	       regs->dcon);
+}
+
+static void
+dmadbg_showchan(const char *fname, int line, struct s3c2410_dma_chan *chan)
+{
+	struct s3c2410_dma_regstate state;
+
+	dmadbg_capture(chan, &state);
+
+	printk(KERN_DEBUG "dma%d: %s:%d: ls=%d, cur=%p, %p %p\n",
+	       chan->number, fname, line, chan->load_state,
+	       chan->curr, chan->next, chan->end);
+
+	dmadbg_dumpregs(fname, line, chan, &state);
+}
+
+static void
+dmadbg_showregs(const char *fname, int line, struct s3c2410_dma_chan *chan)
+{
+	struct s3c2410_dma_regstate state;
+
+	dmadbg_capture(chan, &state);
+	dmadbg_dumpregs(fname, line, chan, &state);
+}
+
+#define dbg_showregs(chan) dmadbg_showregs(__FUNCTION__, __LINE__, (chan))
+#define dbg_showchan(chan) dmadbg_showchan(__FUNCTION__, __LINE__, (chan))
+#else
+#define dbg_showregs(chan) do { } while(0)
+#define dbg_showchan(chan) do { } while(0)
+#endif /* CONFIG_S3C2410_DMA_DEBUG */
+
+static struct s3c2410_dma_chan *dma_chan_map[DMACH_MAX];
+
+/* lookup_dma_channel
+ *
+ * change the dma channel number given into a real dma channel id
+*/
+
+static struct s3c2410_dma_chan *lookup_dma_channel(unsigned int channel)
+{
+	if (channel & DMACH_LOW_LEVEL)
+		return &s3c2410_chans[channel & ~DMACH_LOW_LEVEL];
+	else
+		return dma_chan_map[channel];
+}
+
+/* s3c2410_dma_stats_timeout
+ *
+ * Update DMA stats from timeout info
+*/
+
+static void
+s3c2410_dma_stats_timeout(struct s3c2410_dma_stats *stats, int val)
+{
+	if (stats == NULL)
+		return;
+
+	if (val > stats->timeout_longest)
+		stats->timeout_longest = val;
+	if (val < stats->timeout_shortest)
+		stats->timeout_shortest = val;
+
+	stats->timeout_avg += val;
+}
+
+/* s3c2410_dma_waitforload
+ *
+ * wait for the DMA engine to load a buffer, and update the state accordingly
+*/
+
+static int
+s3c2410_dma_waitforload(struct s3c2410_dma_chan *chan, int line)
+{
+	int timeout = chan->load_timeout;
+	int took;
+
+	if (chan->load_state != S3C2410_DMALOAD_1LOADED) {
+		printk(KERN_ERR "dma%d: s3c2410_dma_waitforload() called in loadstate %d from line %d\n", chan->number, chan->load_state, line);
+		return 0;
+	}
+
+	if (chan->stats != NULL)
+		chan->stats->loads++;
+
+	while (--timeout > 0) {
+		if ((dma_rdreg(chan, S3C2410_DMA_DSTAT) << (32-20)) != 0) {
+			took = chan->load_timeout - timeout;
+
+			s3c2410_dma_stats_timeout(chan->stats, took);
+
+			switch (chan->load_state) {
+			case S3C2410_DMALOAD_1LOADED:
+				chan->load_state = S3C2410_DMALOAD_1RUNNING;
+				break;
+
+			default:
+				printk(KERN_ERR "dma%d: unknown load_state in s3c2410_dma_waitforload() %d\n", chan->number, chan->load_state);
+			}
+
+			return 1;
+		}
+	}
+
+	if (chan->stats != NULL) {
+		chan->stats->timeout_failed++;
+	}
+
+	return 0;
+}
+
+
+
+/* s3c2410_dma_loadbuffer
+ *
+ * load a buffer, and update the channel state
+*/
+
+static inline int
+s3c2410_dma_loadbuffer(struct s3c2410_dma_chan *chan,
+		       struct s3c2410_dma_buf *buf)
+{
+	unsigned long reload;
+
+	pr_debug("s3c2410_chan_loadbuffer: loading buff %p (0x%08lx,0x%06x)\n",
+		 buf, (unsigned long)buf->data, buf->size);
+
+	if (buf == NULL) {
+		dmawarn("buffer is NULL\n");
+		return -EINVAL;
+	}
+
+	/* check the state of the channel before we do anything */
+
+	if (chan->load_state == S3C2410_DMALOAD_1LOADED) {
+		dmawarn("load_state is S3C2410_DMALOAD_1LOADED\n");
+	}
+
+	if (chan->load_state == S3C2410_DMALOAD_1LOADED_1RUNNING) {
+		dmawarn("state is S3C2410_DMALOAD_1LOADED_1RUNNING\n");
+	}
+
+	/* it would seem sensible if we are the last buffer to not bother
+	 * with the auto-reload bit, so that the DMA engine will not try
+	 * and load another transfer after this one has finished...
+	 */
+	if (chan->load_state == S3C2410_DMALOAD_NONE) {
+		pr_debug("load_state is none, checking for noreload (next=%p)\n",
+			 buf->next);
+		reload = (buf->next == NULL) ? S3C2410_DCON_NORELOAD : 0;
+	} else {
+		//pr_debug("load_state is %d => autoreload\n", chan->load_state);
+		reload = S3C2410_DCON_AUTORELOAD;
+	}
+
+	if ((buf->data & 0xf0000000) != 0x30000000) {
+		dmawarn("dmaload: buffer is %p\n", (void *)buf->data);
+	}
+
+	writel(buf->data, chan->addr_reg);
+
+	dma_wrreg(chan, S3C2410_DMA_DCON,
+		  chan->dcon | reload | (buf->size/chan->xfer_unit));
+
+	chan->next = buf->next;
+
+	/* update the state of the channel */
+
+	switch (chan->load_state) {
+	case S3C2410_DMALOAD_NONE:
+		chan->load_state = S3C2410_DMALOAD_1LOADED;
+		break;
+
+	case S3C2410_DMALOAD_1RUNNING:
+		chan->load_state = S3C2410_DMALOAD_1LOADED_1RUNNING;
+		break;
+
+	default:
+		dmawarn("dmaload: unknown state %d in loadbuffer\n",
+			chan->load_state);
+		break;
+	}
+
+	return 0;
+}
+
+/* s3c2410_dma_call_op
+ *
+ * small routine to call the op routine with the given op if it has been
+ * registered
+*/
+
+static void
+s3c2410_dma_call_op(struct s3c2410_dma_chan *chan, enum s3c2410_chan_op op)
+{
+	if (chan->op_fn != NULL) {
+		(chan->op_fn)(chan, op);
+	}
+}
+
+/* s3c2410_dma_buffdone
+ *
+ * small wrapper to check if callback routine needs to be called, and
+ * if so, call it
+*/
+
+static inline void
+s3c2410_dma_buffdone(struct s3c2410_dma_chan *chan, struct s3c2410_dma_buf *buf,
+		     enum s3c2410_dma_buffresult result)
+{
+#if 0
+	pr_debug("callback_fn=%p, buf=%p, id=%p, size=%d, result=%d\n",
+		 chan->callback_fn, buf, buf->id, buf->size, result);
+#endif
+
+	if (chan->callback_fn != NULL) {
+		(chan->callback_fn)(chan, buf->id, buf->size, result);
+	}
+}
+
+/* s3c2410_dma_start
+ *
+ * start a dma channel going
+*/
+
+static int s3c2410_dma_start(struct s3c2410_dma_chan *chan)
+{
+	unsigned long tmp;
+	unsigned long flags;
+
+	pr_debug("s3c2410_start_dma: channel=%d\n", chan->number);
+
+	local_irq_save(flags);
+
+	if (chan->state == S3C2410_DMA_RUNNING) {
+		pr_debug("s3c2410_start_dma: already running (%d)\n", chan->state);
+		local_irq_restore(flags);
+		return 0;
+	}
+
+	chan->state = S3C2410_DMA_RUNNING;
+
+	/* check wether there is anything to load, and if not, see
+	 * if we can find anything to load
+	 */
+
+	if (chan->load_state == S3C2410_DMALOAD_NONE) {
+		if (chan->next == NULL) {
+			printk(KERN_ERR "dma%d: channel has nothing loaded\n",
+			       chan->number);
+			chan->state = S3C2410_DMA_IDLE;
+			local_irq_restore(flags);
+			return -EINVAL;
+		}
+
+		s3c2410_dma_loadbuffer(chan, chan->next);
+	}
+
+	dbg_showchan(chan);
+
+	/* enable the channel */
+
+	if (!chan->irq_enabled) {
+		enable_irq(chan->irq);
+		chan->irq_enabled = 1;
+	}
+
+	/* start the channel going */
+
+	tmp = dma_rdreg(chan, S3C2410_DMA_DMASKTRIG);
+	tmp &= ~S3C2410_DMASKTRIG_STOP;
+	tmp |= S3C2410_DMASKTRIG_ON;
+	dma_wrreg(chan, S3C2410_DMA_DMASKTRIG, tmp);
+
+	pr_debug("dma%d: %08lx to DMASKTRIG\n", chan->number, tmp);
+
+#if 0
+	/* the dma buffer loads should take care of clearing the AUTO
+	 * reloading feature */
+	tmp = dma_rdreg(chan, S3C2410_DMA_DCON);
+	tmp &= ~S3C2410_DCON_NORELOAD;
+	dma_wrreg(chan, S3C2410_DMA_DCON, tmp);
+#endif
+
+	s3c2410_dma_call_op(chan, S3C2410_DMAOP_START);
+
+	dbg_showchan(chan);
+
+	/* if we've only loaded one buffer onto the channel, then chec
+	 * to see if we have another, and if so, try and load it so when
+	 * the first buffer is finished, the new one will be loaded onto
+	 * the channel */
+
+	if (chan->next != NULL) {
+		if (chan->load_state == S3C2410_DMALOAD_1LOADED) {
+
+			if (s3c2410_dma_waitforload(chan, __LINE__) == 0) {
+				pr_debug("%s: buff not yet loaded, no more todo\n",
+					 __FUNCTION__);
+			} else {
+				chan->load_state = S3C2410_DMALOAD_1RUNNING;
+				s3c2410_dma_loadbuffer(chan, chan->next);
+			}
+
+		} else if (chan->load_state == S3C2410_DMALOAD_1RUNNING) {
+			s3c2410_dma_loadbuffer(chan, chan->next);
+		}
+	}
+
+
+	local_irq_restore(flags);
+
+	return 0;
+}
+
+/* s3c2410_dma_canload
+ *
+ * work out if we can queue another buffer into the DMA engine
+*/
+
+static int
+s3c2410_dma_canload(struct s3c2410_dma_chan *chan)
+{
+	if (chan->load_state == S3C2410_DMALOAD_NONE ||
+	    chan->load_state == S3C2410_DMALOAD_1RUNNING)
+		return 1;
+
+	return 0;
+}
+
+/* s3c2410_dma_enqueue
+ *
+ * queue an given buffer for dma transfer.
+ *
+ * id         the device driver's id information for this buffer
+ * data       the physical address of the buffer data
+ * size       the size of the buffer in bytes
+ *
+ * If the channel is not running, then the flag S3C2410_DMAF_AUTOSTART
+ * is checked, and if set, the channel is started. If this flag isn't set,
+ * then an error will be returned.
+ *
+ * It is possible to queue more than one DMA buffer onto a channel at
+ * once, and the code will deal with the re-loading of the next buffer
+ * when necessary.
+*/
+
+int s3c2410_dma_enqueue(unsigned int channel, void *id,
+			dma_addr_t data, int size)
+{
+	struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
+	struct s3c2410_dma_buf *buf;
+	unsigned long flags;
+
+	if (chan == NULL)
+		return -EINVAL;
+
+	pr_debug("%s: id=%p, data=%08x, size=%d\n",
+		 __FUNCTION__, id, (unsigned int)data, size);
+
+	buf = kmem_cache_alloc(dma_kmem, GFP_ATOMIC);
+	if (buf == NULL) {
+		pr_debug("%s: out of memory (%ld alloc)\n",
+			 __FUNCTION__, (long)sizeof(*buf));
+		return -ENOMEM;
+	}
+
+	//pr_debug("%s: new buffer %p\n", __FUNCTION__, buf);
+	//dbg_showchan(chan);
+
+	buf->next  = NULL;
+	buf->data  = buf->ptr = data;
+	buf->size  = size;
+	buf->id    = id;
+	buf->magic = BUF_MAGIC;
+
+	local_irq_save(flags);
+
+	if (chan->curr == NULL) {
+		/* we've got nothing loaded... */
+		pr_debug("%s: buffer %p queued onto empty channel\n",
+			 __FUNCTION__, buf);
+
+		chan->curr = buf;
+		chan->end  = buf;
+		chan->next = NULL;
+	} else {
+		pr_debug("dma%d: %s: buffer %p queued onto non-empty channel\n",
+			 chan->number, __FUNCTION__, buf);
+
+		if (chan->end == NULL)
+			pr_debug("dma%d: %s: %p not empty, and chan->end==NULL?\n",
+				 chan->number, __FUNCTION__, chan);
+
+		chan->end->next = buf;
+		chan->end = buf;
+	}
+
+	/* if necessary, update the next buffer field */
+	if (chan->next == NULL)
+		chan->next = buf;
+
+	/* check to see if we can load a buffer */
+	if (chan->state == S3C2410_DMA_RUNNING) {
+		if (chan->load_state == S3C2410_DMALOAD_1LOADED && 1) {
+			if (s3c2410_dma_waitforload(chan, __LINE__) == 0) {
+				printk(KERN_ERR "dma%d: loadbuffer:"
+				       "timeout loading buffer\n",
+				       chan->number);
+				dbg_showchan(chan);
+				local_irq_restore(flags);
+				return -EINVAL;
+			}
+		}
+
+		while (s3c2410_dma_canload(chan) && chan->next != NULL) {
+			s3c2410_dma_loadbuffer(chan, chan->next);
+		}
+	} else if (chan->state == S3C2410_DMA_IDLE) {
+		if (chan->flags & S3C2410_DMAF_AUTOSTART) {
+			s3c2410_dma_ctrl(chan->number, S3C2410_DMAOP_START);
+		}
+	}
+
+	local_irq_restore(flags);
+	return 0;
+}
+
+EXPORT_SYMBOL(s3c2410_dma_enqueue);
+
+static inline void
+s3c2410_dma_freebuf(struct s3c2410_dma_buf *buf)
+{
+	int magicok = (buf->magic == BUF_MAGIC);
+
+	buf->magic = -1;
+
+	if (magicok) {
+		kmem_cache_free(dma_kmem, buf);
+	} else {
+		printk("s3c2410_dma_freebuf: buff %p with bad magic\n", buf);
+	}
+}
+
+/* s3c2410_dma_lastxfer
+ *
+ * called when the system is out of buffers, to ensure that the channel
+ * is prepared for shutdown.
+*/
+
+static inline void
+s3c2410_dma_lastxfer(struct s3c2410_dma_chan *chan)
+{
+#if 0
+	pr_debug("dma%d: s3c2410_dma_lastxfer: load_state %d\n",
+		 chan->number, chan->load_state);
+#endif
+
+	switch (chan->load_state) {
+	case S3C2410_DMALOAD_NONE:
+		break;
+
+	case S3C2410_DMALOAD_1LOADED:
+		if (s3c2410_dma_waitforload(chan, __LINE__) == 0) {
+				/* flag error? */
+			printk(KERN_ERR "dma%d: timeout waiting for load (%s)\n",
+			       chan->number, __FUNCTION__);
+			return;
+		}
+		break;
+
+	case S3C2410_DMALOAD_1LOADED_1RUNNING:
+		/* I belive in this case we do not have anything to do
+		 * until the next buffer comes along, and we turn off the
+		 * reload */
+		return;
+
+	default:
+		pr_debug("dma%d: lastxfer: unhandled load_state %d with no next\n",
+			 chan->number, chan->load_state);
+		return;
+
+	}
+
+	/* hopefully this'll shut the damned thing up after the transfer... */
+	dma_wrreg(chan, S3C2410_DMA_DCON, chan->dcon | S3C2410_DCON_NORELOAD);
+}
+
+
+#define dmadbg2(x...)
+
+static irqreturn_t
+s3c2410_dma_irq(int irq, void *devpw)
+{
+	struct s3c2410_dma_chan *chan = (struct s3c2410_dma_chan *)devpw;
+	struct s3c2410_dma_buf  *buf;
+
+	buf = chan->curr;
+
+	dbg_showchan(chan);
+
+	/* modify the channel state */
+
+	switch (chan->load_state) {
+	case S3C2410_DMALOAD_1RUNNING:
+		/* TODO - if we are running only one buffer, we probably
+		 * want to reload here, and then worry about the buffer
+		 * callback */
+
+		chan->load_state = S3C2410_DMALOAD_NONE;
+		break;
+
+	case S3C2410_DMALOAD_1LOADED:
+		/* iirc, we should go back to NONE loaded here, we
+		 * had a buffer, and it was never verified as being
+		 * loaded.
+		 */
+
+		chan->load_state = S3C2410_DMALOAD_NONE;
+		break;
+
+	case S3C2410_DMALOAD_1LOADED_1RUNNING:
+		/* we'll worry about checking to see if another buffer is
+		 * ready after we've called back the owner. This should
+		 * ensure we do not wait around too long for the DMA
+		 * engine to start the next transfer
+		 */
+
+		chan->load_state = S3C2410_DMALOAD_1LOADED;
+		break;
+
+	case S3C2410_DMALOAD_NONE:
+		printk(KERN_ERR "dma%d: IRQ with no loaded buffer?\n",
+		       chan->number);
+		break;
+
+	default:
+		printk(KERN_ERR "dma%d: IRQ in invalid load_state %d\n",
+		       chan->number, chan->load_state);
+		break;
+	}
+
+	if (buf != NULL) {
+		/* update the chain to make sure that if we load any more
+		 * buffers when we call the callback function, things should
+		 * work properly */
+
+		chan->curr = buf->next;
+		buf->next  = NULL;
+
+		if (buf->magic != BUF_MAGIC) {
+			printk(KERN_ERR "dma%d: %s: buf %p incorrect magic\n",
+			       chan->number, __FUNCTION__, buf);
+			return IRQ_HANDLED;
+		}
+
+		s3c2410_dma_buffdone(chan, buf, S3C2410_RES_OK);
+
+		/* free resouces */
+		s3c2410_dma_freebuf(buf);
+	} else {
+	}
+
+	/* only reload if the channel is still running... our buffer done
+	 * routine may have altered the state by requesting the dma channel
+	 * to stop or shutdown... */
+
+	/* todo: check that when the channel is shut-down from inside this
+	 * function, we cope with unsetting reload, etc */
+
+	if (chan->next != NULL && chan->state != S3C2410_DMA_IDLE) {
+		unsigned long flags;
+
+		switch (chan->load_state) {
+		case S3C2410_DMALOAD_1RUNNING:
+			/* don't need to do anything for this state */
+			break;
+
+		case S3C2410_DMALOAD_NONE:
+			/* can load buffer immediately */
+			break;
+
+		case S3C2410_DMALOAD_1LOADED:
+			if (s3c2410_dma_waitforload(chan, __LINE__) == 0) {
+				/* flag error? */
+				printk(KERN_ERR "dma%d: timeout waiting for load (%s)\n",
+				       chan->number, __FUNCTION__);
+				return IRQ_HANDLED;
+			}
+
+			break;
+
+		case S3C2410_DMALOAD_1LOADED_1RUNNING:
+			goto no_load;
+
+		default:
+			printk(KERN_ERR "dma%d: unknown load_state in irq, %d\n",
+			       chan->number, chan->load_state);
+			return IRQ_HANDLED;
+		}
+
+		local_irq_save(flags);
+		s3c2410_dma_loadbuffer(chan, chan->next);
+		local_irq_restore(flags);
+	} else {
+		s3c2410_dma_lastxfer(chan);
+
+		/* see if we can stop this channel.. */
+		if (chan->load_state == S3C2410_DMALOAD_NONE) {
+			pr_debug("dma%d: end of transfer, stopping channel (%ld)\n",
+				 chan->number, jiffies);
+			s3c2410_dma_ctrl(chan->number | DMACH_LOW_LEVEL,
+					 S3C2410_DMAOP_STOP);
+		}
+	}
+
+ no_load:
+	return IRQ_HANDLED;
+}
+
+static struct s3c2410_dma_chan *s3c2410_dma_map_channel(int channel);
+
+/* s3c2410_request_dma
+ *
+ * get control of an dma channel
+*/
+
+int s3c2410_dma_request(unsigned int channel,
+			struct s3c2410_dma_client *client,
+			void *dev)
+{
+	struct s3c2410_dma_chan *chan;
+	unsigned long flags;
+	int err;
+
+	pr_debug("dma%d: s3c2410_request_dma: client=%s, dev=%p\n",
+		 channel, client->name, dev);
+
+	local_irq_save(flags);
+
+	chan = s3c2410_dma_map_channel(channel);
+	if (chan == NULL) {
+		local_irq_restore(flags);
+		return -EBUSY;
+	}
+
+	dbg_showchan(chan);
+
+	chan->client = client;
+	chan->in_use = 1;
+
+	if (!chan->irq_claimed) {
+		pr_debug("dma%d: %s : requesting irq %d\n",
+			 channel, __FUNCTION__, chan->irq);
+
+		chan->irq_claimed = 1;
+		local_irq_restore(flags);
+
+		err = request_irq(chan->irq, s3c2410_dma_irq, IRQF_DISABLED,
+				  client->name, (void *)chan);
+
+		local_irq_save(flags);
+
+		if (err) {
+			chan->in_use = 0;
+			chan->irq_claimed = 0;
+			local_irq_restore(flags);
+
+			printk(KERN_ERR "%s: cannot get IRQ %d for DMA %d\n",
+			       client->name, chan->irq, chan->number);
+			return err;
+		}
+
+		chan->irq_enabled = 1;
+	}
+
+	local_irq_restore(flags);
+
+	/* need to setup */
+
+	pr_debug("%s: channel initialised, %p\n", __FUNCTION__, chan);
+
+	return 0;
+}
+
+EXPORT_SYMBOL(s3c2410_dma_request);
+
+/* s3c2410_dma_free
+ *
+ * release the given channel back to the system, will stop and flush
+ * any outstanding transfers, and ensure the channel is ready for the
+ * next claimant.
+ *
+ * Note, although a warning is currently printed if the freeing client
+ * info is not the same as the registrant's client info, the free is still
+ * allowed to go through.
+*/
+
+int s3c2410_dma_free(dmach_t channel, struct s3c2410_dma_client *client)
+{
+	struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
+	unsigned long flags;
+
+	if (chan == NULL)
+		return -EINVAL;
+
+	local_irq_save(flags);
+
+	if (chan->client != client) {
+		printk(KERN_WARNING "dma%d: possible free from different client (channel %p, passed %p)\n",
+		       channel, chan->client, client);
+	}
+
+	/* sort out stopping and freeing the channel */
+
+	if (chan->state != S3C2410_DMA_IDLE) {
+		pr_debug("%s: need to stop dma channel %p\n",
+		       __FUNCTION__, chan);
+
+		/* possibly flush the channel */
+		s3c2410_dma_ctrl(channel, S3C2410_DMAOP_STOP);
+	}
+
+	chan->client = NULL;
+	chan->in_use = 0;
+
+	if (chan->irq_claimed)
+		free_irq(chan->irq, (void *)chan);
+
+	chan->irq_claimed = 0;
+
+	if (!(channel & DMACH_LOW_LEVEL))
+		dma_chan_map[channel] = NULL;
+
+	local_irq_restore(flags);
+
+	return 0;
+}
+
+EXPORT_SYMBOL(s3c2410_dma_free);
+
+static int s3c2410_dma_dostop(struct s3c2410_dma_chan *chan)
+{
+	unsigned long flags;
+	unsigned long tmp;
+
+	pr_debug("%s:\n", __FUNCTION__);
+
+	dbg_showchan(chan);
+
+	local_irq_save(flags);
+
+	s3c2410_dma_call_op(chan,  S3C2410_DMAOP_STOP);
+
+	tmp = dma_rdreg(chan, S3C2410_DMA_DMASKTRIG);
+	tmp |= S3C2410_DMASKTRIG_STOP;
+	//tmp &= ~S3C2410_DMASKTRIG_ON;
+	dma_wrreg(chan, S3C2410_DMA_DMASKTRIG, tmp);
+
+#if 0
+	/* should also clear interrupts, according to WinCE BSP */
+	tmp = dma_rdreg(chan, S3C2410_DMA_DCON);
+	tmp |= S3C2410_DCON_NORELOAD;
+	dma_wrreg(chan, S3C2410_DMA_DCON, tmp);
+#endif
+
+	/* should stop do this, or should we wait for flush? */
+	chan->state      = S3C2410_DMA_IDLE;
+	chan->load_state = S3C2410_DMALOAD_NONE;
+
+	local_irq_restore(flags);
+
+	return 0;
+}
+
+void s3c2410_dma_waitforstop(struct s3c2410_dma_chan *chan)
+{
+	unsigned long tmp;
+	unsigned int timeout = 0x10000;
+
+	while (timeout-- > 0) {
+		tmp = dma_rdreg(chan, S3C2410_DMA_DMASKTRIG);
+
+		if (!(tmp & S3C2410_DMASKTRIG_ON))
+			return;
+	}
+
+	pr_debug("dma%d: failed to stop?\n", chan->number);
+}
+
+
+/* s3c2410_dma_flush
+ *
+ * stop the channel, and remove all current and pending transfers
+*/
+
+static int s3c2410_dma_flush(struct s3c2410_dma_chan *chan)
+{
+	struct s3c2410_dma_buf *buf, *next;
+	unsigned long flags;
+
+	pr_debug("%s: chan %p (%d)\n", __FUNCTION__, chan, chan->number);
+
+	dbg_showchan(chan);
+
+	local_irq_save(flags);
+
+	if (chan->state != S3C2410_DMA_IDLE) {
+		pr_debug("%s: stopping channel...\n", __FUNCTION__ );
+		s3c2410_dma_ctrl(chan->number, S3C2410_DMAOP_STOP);
+	}
+
+	buf = chan->curr;
+	if (buf == NULL)
+		buf = chan->next;
+
+	chan->curr = chan->next = chan->end = NULL;
+
+	if (buf != NULL) {
+		for ( ; buf != NULL; buf = next) {
+			next = buf->next;
+
+			pr_debug("%s: free buffer %p, next %p\n",
+			       __FUNCTION__, buf, buf->next);
+
+			s3c2410_dma_buffdone(chan, buf, S3C2410_RES_ABORT);
+			s3c2410_dma_freebuf(buf);
+		}
+	}
+
+	dbg_showregs(chan);
+
+	s3c2410_dma_waitforstop(chan);
+
+#if 0
+	/* should also clear interrupts, according to WinCE BSP */
+	{
+		unsigned long tmp;
+
+		tmp = dma_rdreg(chan, S3C2410_DMA_DCON);
+		tmp |= S3C2410_DCON_NORELOAD;
+		dma_wrreg(chan, S3C2410_DMA_DCON, tmp);
+	}
+#endif
+
+	dbg_showregs(chan);
+
+	local_irq_restore(flags);
+
+	return 0;
+}
+
+int
+s3c2410_dma_started(struct s3c2410_dma_chan *chan)
+{
+	unsigned long flags;
+
+	local_irq_save(flags);
+
+	dbg_showchan(chan);
+
+	/* if we've only loaded one buffer onto the channel, then chec
+	 * to see if we have another, and if so, try and load it so when
+	 * the first buffer is finished, the new one will be loaded onto
+	 * the channel */
+
+	if (chan->next != NULL) {
+		if (chan->load_state == S3C2410_DMALOAD_1LOADED) {
+
+			if (s3c2410_dma_waitforload(chan, __LINE__) == 0) {
+				pr_debug("%s: buff not yet loaded, no more todo\n",
+					 __FUNCTION__);
+			} else {
+				chan->load_state = S3C2410_DMALOAD_1RUNNING;
+				s3c2410_dma_loadbuffer(chan, chan->next);
+			}
+
+		} else if (chan->load_state == S3C2410_DMALOAD_1RUNNING) {
+			s3c2410_dma_loadbuffer(chan, chan->next);
+		}
+	}
+
+
+	local_irq_restore(flags);
+
+	return 0;
+
+}
+
+int
+s3c2410_dma_ctrl(dmach_t channel, enum s3c2410_chan_op op)
+{
+	struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
+
+	if (chan == NULL)
+		return -EINVAL;
+
+	switch (op) {
+	case S3C2410_DMAOP_START:
+		return s3c2410_dma_start(chan);
+
+	case S3C2410_DMAOP_STOP:
+		return s3c2410_dma_dostop(chan);
+
+	case S3C2410_DMAOP_PAUSE:
+	case S3C2410_DMAOP_RESUME:
+		return -ENOENT;
+
+	case S3C2410_DMAOP_FLUSH:
+		return s3c2410_dma_flush(chan);
+
+	case S3C2410_DMAOP_STARTED:
+		return s3c2410_dma_started(chan);
+
+	case S3C2410_DMAOP_TIMEOUT:
+		return 0;
+
+	}
+
+	return -ENOENT;      /* unknown, don't bother */
+}
+
+EXPORT_SYMBOL(s3c2410_dma_ctrl);
+
+/* DMA configuration for each channel
+ *
+ * DISRCC -> source of the DMA (AHB,APB)
+ * DISRC  -> source address of the DMA
+ * DIDSTC -> destination of the DMA (AHB,APD)
+ * DIDST  -> destination address of the DMA
+*/
+
+/* s3c2410_dma_config
+ *
+ * xfersize:     size of unit in bytes (1,2,4)
+ * dcon:         base value of the DCONx register
+*/
+
+int s3c2410_dma_config(dmach_t channel,
+		       int xferunit,
+		       int dcon)
+{
+	struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
+
+	pr_debug("%s: chan=%d, xfer_unit=%d, dcon=%08x\n",
+		 __FUNCTION__, channel, xferunit, dcon);
+
+	if (chan == NULL)
+		return -EINVAL;
+
+	pr_debug("%s: Initial dcon is %08x\n", __FUNCTION__, dcon);
+
+	dcon |= chan->dcon & dma_sel.dcon_mask;
+
+	pr_debug("%s: New dcon is %08x\n", __FUNCTION__, dcon);
+
+	switch (xferunit) {
+	case 1:
+		dcon |= S3C2410_DCON_BYTE;
+		break;
+
+	case 2:
+		dcon |= S3C2410_DCON_HALFWORD;
+		break;
+
+	case 4:
+		dcon |= S3C2410_DCON_WORD;
+		break;
+
+	default:
+		pr_debug("%s: bad transfer size %d\n", __FUNCTION__, xferunit);
+		return -EINVAL;
+	}
+
+	dcon |= S3C2410_DCON_HWTRIG;
+	dcon |= S3C2410_DCON_INTREQ;
+
+	pr_debug("%s: dcon now %08x\n", __FUNCTION__, dcon);
+
+	chan->dcon = dcon;
+	chan->xfer_unit = xferunit;
+
+	return 0;
+}
+
+EXPORT_SYMBOL(s3c2410_dma_config);
+
+int s3c2410_dma_setflags(dmach_t channel, unsigned int flags)
+{
+	struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
+
+	if (chan == NULL)
+		return -EINVAL;
+
+	pr_debug("%s: chan=%p, flags=%08x\n", __FUNCTION__, chan, flags);
+
+	chan->flags = flags;
+
+	return 0;
+}
+
+EXPORT_SYMBOL(s3c2410_dma_setflags);
+
+
+/* do we need to protect the settings of the fields from
+ * irq?
+*/
+
+int s3c2410_dma_set_opfn(dmach_t channel, s3c2410_dma_opfn_t rtn)
+{
+	struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
+
+	if (chan == NULL)
+		return -EINVAL;
+
+	pr_debug("%s: chan=%p, op rtn=%p\n", __FUNCTION__, chan, rtn);
+
+	chan->op_fn = rtn;
+
+	return 0;
+}
+
+EXPORT_SYMBOL(s3c2410_dma_set_opfn);
+
+int s3c2410_dma_set_buffdone_fn(dmach_t channel, s3c2410_dma_cbfn_t rtn)
+{
+	struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
+
+	if (chan == NULL)
+		return -EINVAL;
+
+	pr_debug("%s: chan=%p, callback rtn=%p\n", __FUNCTION__, chan, rtn);
+
+	chan->callback_fn = rtn;
+
+	return 0;
+}
+
+EXPORT_SYMBOL(s3c2410_dma_set_buffdone_fn);
+
+/* s3c2410_dma_devconfig
+ *
+ * configure the dma source/destination hardware type and address
+ *
+ * source:    S3C2410_DMASRC_HW: source is hardware
+ *            S3C2410_DMASRC_MEM: source is memory
+ *
+ * hwcfg:     the value for xxxSTCn register,
+ *            bit 0: 0=increment pointer, 1=leave pointer
+ *            bit 1: 0=soucre is AHB, 1=soucre is APB
+ *
+ * devaddr:   physical address of the source
+*/
+
+int s3c2410_dma_devconfig(int channel,
+			  enum s3c2410_dmasrc source,
+			  int hwcfg,
+			  unsigned long devaddr)
+{
+	struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
+
+	if (chan == NULL)
+		return -EINVAL;
+
+	pr_debug("%s: source=%d, hwcfg=%08x, devaddr=%08lx\n",
+		 __FUNCTION__, (int)source, hwcfg, devaddr);
+
+	chan->source = source;
+	chan->dev_addr = devaddr;
+
+	switch (source) {
+	case S3C2410_DMASRC_HW:
+		/* source is hardware */
+		pr_debug("%s: hw source, devaddr=%08lx, hwcfg=%d\n",
+			 __FUNCTION__, devaddr, hwcfg);
+		dma_wrreg(chan, S3C2410_DMA_DISRCC, hwcfg & 3);
+		dma_wrreg(chan, S3C2410_DMA_DISRC,  devaddr);
+		dma_wrreg(chan, S3C2410_DMA_DIDSTC, (0<<1) | (0<<0));
+
+		chan->addr_reg = dma_regaddr(chan, S3C2410_DMA_DIDST);
+		return 0;
+
+	case S3C2410_DMASRC_MEM:
+		/* source is memory */
+		pr_debug( "%s: mem source, devaddr=%08lx, hwcfg=%d\n",
+			  __FUNCTION__, devaddr, hwcfg);
+		dma_wrreg(chan, S3C2410_DMA_DISRCC, (0<<1) | (0<<0));
+		dma_wrreg(chan, S3C2410_DMA_DIDST,  devaddr);
+		dma_wrreg(chan, S3C2410_DMA_DIDSTC, hwcfg & 3);
+
+		chan->addr_reg = dma_regaddr(chan, S3C2410_DMA_DISRC);
+		return 0;
+	}
+
+	printk(KERN_ERR "dma%d: invalid source type (%d)\n", channel, source);
+	return -EINVAL;
+}
+
+EXPORT_SYMBOL(s3c2410_dma_devconfig);
+
+/* s3c2410_dma_getposition
+ *
+ * returns the current transfer points for the dma source and destination
+*/
+
+int s3c2410_dma_getposition(dmach_t channel, dma_addr_t *src, dma_addr_t *dst)
+{
+ 	struct s3c2410_dma_chan *chan = lookup_dma_channel(channel);
+
+	if (chan == NULL)
+		return -EINVAL;
+
+	if (src != NULL)
+ 		*src = dma_rdreg(chan, S3C2410_DMA_DCSRC);
+
+ 	if (dst != NULL)
+ 		*dst = dma_rdreg(chan, S3C2410_DMA_DCDST);
+
+ 	return 0;
+}
+
+EXPORT_SYMBOL(s3c2410_dma_getposition);
+
+
+/* system device class */
+
+#ifdef CONFIG_PM
+
+static int s3c2410_dma_suspend(struct sys_device *dev, pm_message_t state)
+{
+	struct s3c2410_dma_chan *cp = container_of(dev, struct s3c2410_dma_chan, dev);
+
+	printk(KERN_DEBUG "suspending dma channel %d\n", cp->number);
+
+	if (dma_rdreg(cp, S3C2410_DMA_DMASKTRIG) & S3C2410_DMASKTRIG_ON) {
+		/* the dma channel is still working, which is probably
+		 * a bad thing to do over suspend/resume. We stop the
+		 * channel and assume that the client is either going to
+		 * retry after resume, or that it is broken.
+		 */
+
+		printk(KERN_INFO "dma: stopping channel %d due to suspend\n",
+		       cp->number);
+
+		s3c2410_dma_dostop(cp);
+	}
+
+	return 0;
+}
+
+static int s3c2410_dma_resume(struct sys_device *dev)
+{
+	return 0;
+}
+
+#else
+#define s3c2410_dma_suspend NULL
+#define s3c2410_dma_resume  NULL
+#endif /* CONFIG_PM */
+
+struct sysdev_class dma_sysclass = {
+	set_kset_name("s3c24xx-dma"),
+	.suspend	= s3c2410_dma_suspend,
+	.resume		= s3c2410_dma_resume,
+};
+
+/* kmem cache implementation */
+
+static void s3c2410_dma_cache_ctor(void *p, struct kmem_cache *c, unsigned long f)
+{
+	memset(p, 0, sizeof(struct s3c2410_dma_buf));
+}
+
+/* initialisation code */
+
+int __init s3c24xx_dma_sysclass_init(void)
+{
+	int ret = sysdev_class_register(&dma_sysclass);
+
+	if (ret != 0)
+		printk(KERN_ERR "dma sysclass registration failed\n");
+
+	return ret;
+}
+
+core_initcall(s3c24xx_dma_sysclass_init);
+
+int __init s3c24xx_dma_sysdev_register(void)
+{
+	struct s3c2410_dma_chan *cp = s3c2410_chans;
+	int channel, ret;
+
+	for (channel = 0; channel < dma_channels; cp++, channel++) {
+		cp->dev.cls = &dma_sysclass;
+		cp->dev.id  = channel;
+		ret = sysdev_register(&cp->dev);
+
+		if (ret) {
+			printk(KERN_ERR "error registering dev for dma %d\n",
+			       channel);
+ 			return ret;
+		}
+	}
+
+	return 0;
+}
+
+late_initcall(s3c24xx_dma_sysdev_register);
+
+int __init s3c24xx_dma_init(unsigned int channels, unsigned int irq,
+			    unsigned int stride)
+{
+	struct s3c2410_dma_chan *cp;
+	int channel;
+	int ret;
+
+	printk("S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics\n");
+
+	dma_channels = channels;
+
+	dma_base = ioremap(S3C24XX_PA_DMA, stride * channels);
+	if (dma_base == NULL) {
+		printk(KERN_ERR "dma failed to remap register block\n");
+		return -ENOMEM;
+	}
+
+	dma_kmem = kmem_cache_create("dma_desc",
+				     sizeof(struct s3c2410_dma_buf), 0,
+				     SLAB_HWCACHE_ALIGN,
+				     s3c2410_dma_cache_ctor, NULL);
+
+	if (dma_kmem == NULL) {
+		printk(KERN_ERR "dma failed to make kmem cache\n");
+		ret = -ENOMEM;
+		goto err;
+	}
+
+	for (channel = 0; channel < channels;  channel++) {
+		cp = &s3c2410_chans[channel];
+
+		memset(cp, 0, sizeof(struct s3c2410_dma_chan));
+
+		/* dma channel irqs are in order.. */
+		cp->number = channel;
+		cp->irq    = channel + irq;
+		cp->regs   = dma_base + (channel * stride);
+
+		/* point current stats somewhere */
+		cp->stats  = &cp->stats_store;
+		cp->stats_store.timeout_shortest = LONG_MAX;
+
+		/* basic channel configuration */
+
+		cp->load_timeout = 1<<18;
+
+		printk("DMA channel %d at %p, irq %d\n",
+		       cp->number, cp->regs, cp->irq);
+	}
+
+	return 0;
+
+ err:
+	kmem_cache_destroy(dma_kmem);
+	iounmap(dma_base);
+	dma_base = NULL;
+	return ret;
+}
+
+int s3c2410_dma_init(void)
+{
+	return s3c24xx_dma_init(4, IRQ_DMA0, 0x40);
+}
+
+static inline int is_channel_valid(unsigned int channel)
+{
+	return (channel & DMA_CH_VALID);
+}
+
+static struct s3c24xx_dma_order *dma_order;
+
+
+/* s3c2410_dma_map_channel()
+ *
+ * turn the virtual channel number into a real, and un-used hardware
+ * channel.
+ *
+ * first, try the dma ordering given to us by either the relevant
+ * dma code, or the board. Then just find the first usable free
+ * channel
+*/
+
+struct s3c2410_dma_chan *s3c2410_dma_map_channel(int channel)
+{
+	struct s3c24xx_dma_order_ch *ord = NULL;
+	struct s3c24xx_dma_map *ch_map;
+	struct s3c2410_dma_chan *dmach;
+	int ch;
+
+	if (dma_sel.map == NULL || channel > dma_sel.map_size)
+		return NULL;
+
+	ch_map = dma_sel.map + channel;
+
+	/* first, try the board mapping */
+
+	if (dma_order) {
+		ord = &dma_order->channels[channel];
+
+		for (ch = 0; ch < dma_channels; ch++) {
+			if (!is_channel_valid(ord->list[ch]))
+				continue;
+
+			if (s3c2410_chans[ord->list[ch]].in_use == 0) {
+				ch = ord->list[ch] & ~DMA_CH_VALID;
+				goto found;
+			}
+		}
+
+		if (ord->flags & DMA_CH_NEVER)
+			return NULL;
+	}
+
+	/* second, search the channel map for first free */
+
+	for (ch = 0; ch < dma_channels; ch++) {
+		if (!is_channel_valid(ch_map->channels[ch]))
+			continue;
+
+		if (s3c2410_chans[ch].in_use == 0) {
+			printk("mapped channel %d to %d\n", channel, ch);
+			break;
+		}
+	}
+
+	if (ch >= dma_channels)
+		return NULL;
+
+	/* update our channel mapping */
+
+ found:
+	dmach = &s3c2410_chans[ch];
+	dma_chan_map[channel] = dmach;
+
+	/* select the channel */
+
+	(dma_sel.select)(dmach, ch_map);
+
+	return dmach;
+}
+
+static int s3c24xx_dma_check_entry(struct s3c24xx_dma_map *map, int ch)
+{
+	return 0;
+}
+
+int __init s3c24xx_dma_init_map(struct s3c24xx_dma_selection *sel)
+{
+	struct s3c24xx_dma_map *nmap;
+	size_t map_sz = sizeof(*nmap) * sel->map_size;
+	int ptr;
+
+	nmap = kmalloc(map_sz, GFP_KERNEL);
+	if (nmap == NULL)
+		return -ENOMEM;
+
+	memcpy(nmap, sel->map, map_sz);
+	memcpy(&dma_sel, sel, sizeof(*sel));
+
+	dma_sel.map = nmap;
+
+	for (ptr = 0; ptr < sel->map_size; ptr++)
+		s3c24xx_dma_check_entry(nmap+ptr, ptr);
+
+	return 0;
+}
+
+int __init s3c24xx_dma_order_set(struct s3c24xx_dma_order *ord)
+{
+	struct s3c24xx_dma_order *nord = dma_order;
+
+	if (nord == NULL)
+		nord = kmalloc(sizeof(struct s3c24xx_dma_order), GFP_KERNEL);
+
+	if (nord == NULL) {
+		printk(KERN_ERR "no memory to store dma channel order\n");
+		return -ENOMEM;
+	}
+
+	dma_order = nord;
+	memcpy(nord, ord, sizeof(struct s3c24xx_dma_order));
+	return 0;
+}
diff --git a/arch/arm/plat-s3c24xx/gpio.c b/arch/arm/plat-s3c24xx/gpio.c
new file mode 100644
index 00000000000..ec3a09c4d18
--- /dev/null
+++ b/arch/arm/plat-s3c24xx/gpio.c
@@ -0,0 +1,188 @@
+/* linux/arch/arm/plat-s3c24xx/gpio.c
+ *
+ * Copyright (c) 2004-2005 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C24XX GPIO support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+*/
+
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+
+#include <asm/hardware.h>
+#include <asm/irq.h>
+#include <asm/io.h>
+
+#include <asm/arch/regs-gpio.h>
+
+void s3c2410_gpio_cfgpin(unsigned int pin, unsigned int function)
+{
+	void __iomem *base = S3C24XX_GPIO_BASE(pin);
+	unsigned long mask;
+	unsigned long con;
+	unsigned long flags;
+
+	if (pin < S3C2410_GPIO_BANKB) {
+		mask = 1 << S3C2410_GPIO_OFFSET(pin);
+	} else {
+		mask = 3 << S3C2410_GPIO_OFFSET(pin)*2;
+	}
+
+	switch (function) {
+	case S3C2410_GPIO_LEAVE:
+		mask = 0;
+		function = 0;
+		break;
+
+	case S3C2410_GPIO_INPUT:
+	case S3C2410_GPIO_OUTPUT:
+	case S3C2410_GPIO_SFN2:
+	case S3C2410_GPIO_SFN3:
+		if (pin < S3C2410_GPIO_BANKB) {
+			function -= 1;
+			function &= 1;
+			function <<= S3C2410_GPIO_OFFSET(pin);
+		} else {
+			function &= 3;
+			function <<= S3C2410_GPIO_OFFSET(pin)*2;
+		}
+	}
+
+	/* modify the specified register wwith IRQs off */
+
+	local_irq_save(flags);
+
+	con  = __raw_readl(base + 0x00);
+	con &= ~mask;
+	con |= function;
+
+	__raw_writel(con, base + 0x00);
+
+	local_irq_restore(flags);
+}
+
+EXPORT_SYMBOL(s3c2410_gpio_cfgpin);
+
+unsigned int s3c2410_gpio_getcfg(unsigned int pin)
+{
+	void __iomem *base = S3C24XX_GPIO_BASE(pin);
+	unsigned long val = __raw_readl(base);
+
+	if (pin < S3C2410_GPIO_BANKB) {
+		val >>= S3C2410_GPIO_OFFSET(pin);
+		val &= 1;
+		val += 1;
+	} else {
+		val >>= S3C2410_GPIO_OFFSET(pin)*2;
+		val &= 3;
+	}
+
+	return val | S3C2410_GPIO_INPUT;
+}
+
+EXPORT_SYMBOL(s3c2410_gpio_getcfg);
+
+void s3c2410_gpio_pullup(unsigned int pin, unsigned int to)
+{
+	void __iomem *base = S3C24XX_GPIO_BASE(pin);
+	unsigned long offs = S3C2410_GPIO_OFFSET(pin);
+	unsigned long flags;
+	unsigned long up;
+
+	if (pin < S3C2410_GPIO_BANKB)
+		return;
+
+	local_irq_save(flags);
+
+	up = __raw_readl(base + 0x08);
+	up &= ~(1L << offs);
+	up |= to << offs;
+	__raw_writel(up, base + 0x08);
+
+	local_irq_restore(flags);
+}
+
+EXPORT_SYMBOL(s3c2410_gpio_pullup);
+
+void s3c2410_gpio_setpin(unsigned int pin, unsigned int to)
+{
+	void __iomem *base = S3C24XX_GPIO_BASE(pin);
+	unsigned long offs = S3C2410_GPIO_OFFSET(pin);
+	unsigned long flags;
+	unsigned long dat;
+
+	local_irq_save(flags);
+
+	dat = __raw_readl(base + 0x04);
+	dat &= ~(1 << offs);
+	dat |= to << offs;
+	__raw_writel(dat, base + 0x04);
+
+	local_irq_restore(flags);
+}
+
+EXPORT_SYMBOL(s3c2410_gpio_setpin);
+
+unsigned int s3c2410_gpio_getpin(unsigned int pin)
+{
+	void __iomem *base = S3C24XX_GPIO_BASE(pin);
+	unsigned long offs = S3C2410_GPIO_OFFSET(pin);
+
+	return __raw_readl(base + 0x04) & (1<< offs);
+}
+
+EXPORT_SYMBOL(s3c2410_gpio_getpin);
+
+unsigned int s3c2410_modify_misccr(unsigned int clear, unsigned int change)
+{
+	unsigned long flags;
+	unsigned long misccr;
+
+	local_irq_save(flags);
+	misccr = __raw_readl(S3C24XX_MISCCR);
+	misccr &= ~clear;
+	misccr ^= change;
+	__raw_writel(misccr, S3C24XX_MISCCR);
+	local_irq_restore(flags);
+
+	return misccr;
+}
+
+EXPORT_SYMBOL(s3c2410_modify_misccr);
+
+int s3c2410_gpio_getirq(unsigned int pin)
+{
+	if (pin < S3C2410_GPF0 || pin > S3C2410_GPG15)
+		return -1;	/* not valid interrupts */
+
+	if (pin < S3C2410_GPG0 && pin > S3C2410_GPF7)
+		return -1;	/* not valid pin */
+
+	if (pin < S3C2410_GPF4)
+		return (pin - S3C2410_GPF0) + IRQ_EINT0;
+
+	if (pin < S3C2410_GPG0)
+		return (pin - S3C2410_GPF4) + IRQ_EINT4;
+
+	return (pin - S3C2410_GPG0) + IRQ_EINT8;
+}
+
+EXPORT_SYMBOL(s3c2410_gpio_getirq);
diff --git a/arch/arm/plat-s3c24xx/irq.c b/arch/arm/plat-s3c24xx/irq.c
new file mode 100644
index 00000000000..ce186398e3f
--- /dev/null
+++ b/arch/arm/plat-s3c24xx/irq.c
@@ -0,0 +1,801 @@
+/* linux/arch/arm/plat-s3c24xx/irq.c
+ *
+ * Copyright (c) 2003,2004 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ *
+ * Changelog:
+ *
+ *   22-Jul-2004  Ben Dooks <ben@simtec.co.uk>
+ *                Fixed compile warnings
+ *
+ *   22-Jul-2004  Roc Wu <cooloney@yahoo.com.cn>
+ *                Fixed s3c_extirq_type
+ *
+ *   21-Jul-2004  Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org>
+ *                Addition of ADC/TC demux
+ *
+ *   04-Oct-2004  Klaus Fetscher <k.fetscher@fetron.de>
+ *		  Fix for set_irq_type() on low EINT numbers
+ *
+ *   05-Oct-2004  Ben Dooks <ben@simtec.co.uk>
+ *		  Tidy up KF's patch and sort out new release
+ *
+ *   05-Oct-2004  Ben Dooks <ben@simtec.co.uk>
+ *		  Add support for power management controls
+ *
+ *   04-Nov-2004  Ben Dooks
+ *		  Fix standard IRQ wake for EINT0..4 and RTC
+ *
+ *   22-Feb-2005  Ben Dooks
+ *		  Fixed edge-triggering on ADC IRQ
+ *
+ *   28-Jun-2005  Ben Dooks
+ *		  Mark IRQ_LCD valid
+ *
+ *   25-Jul-2005  Ben Dooks
+ *		  Split the S3C2440 IRQ code to seperate file
+*/
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/ptrace.h>
+#include <linux/sysdev.h>
+
+#include <asm/hardware.h>
+#include <asm/irq.h>
+#include <asm/io.h>
+
+#include <asm/mach/irq.h>
+
+#include <asm/arch/regs-irq.h>
+#include <asm/arch/regs-gpio.h>
+
+#include <asm/plat-s3c24xx/cpu.h>
+#include <asm/plat-s3c24xx/pm.h>
+#include <asm/plat-s3c24xx/irq.h>
+
+/* wakeup irq control */
+
+#ifdef CONFIG_PM
+
+/* state for IRQs over sleep */
+
+/* default is to allow for EINT0..EINT15, and IRQ_RTC as wakeup sources
+ *
+ * set bit to 1 in allow bitfield to enable the wakeup settings on it
+*/
+
+unsigned long s3c_irqwake_intallow	= 1L << (IRQ_RTC - IRQ_EINT0) | 0xfL;
+unsigned long s3c_irqwake_intmask	= 0xffffffffL;
+unsigned long s3c_irqwake_eintallow	= 0x0000fff0L;
+unsigned long s3c_irqwake_eintmask	= 0xffffffffL;
+
+int
+s3c_irq_wake(unsigned int irqno, unsigned int state)
+{
+	unsigned long irqbit = 1 << (irqno - IRQ_EINT0);
+
+	if (!(s3c_irqwake_intallow & irqbit))
+		return -ENOENT;
+
+	printk(KERN_INFO "wake %s for irq %d\n",
+	       state ? "enabled" : "disabled", irqno);
+
+	if (!state)
+		s3c_irqwake_intmask |= irqbit;
+	else
+		s3c_irqwake_intmask &= ~irqbit;
+
+	return 0;
+}
+
+static int
+s3c_irqext_wake(unsigned int irqno, unsigned int state)
+{
+	unsigned long bit = 1L << (irqno - EXTINT_OFF);
+
+	if (!(s3c_irqwake_eintallow & bit))
+		return -ENOENT;
+
+	printk(KERN_INFO "wake %s for irq %d\n",
+	       state ? "enabled" : "disabled", irqno);
+
+	if (!state)
+		s3c_irqwake_eintmask |= bit;
+	else
+		s3c_irqwake_eintmask &= ~bit;
+
+	return 0;
+}
+
+#else
+#define s3c_irqext_wake NULL
+#define s3c_irq_wake NULL
+#endif
+
+
+static void
+s3c_irq_mask(unsigned int irqno)
+{
+	unsigned long mask;
+
+	irqno -= IRQ_EINT0;
+
+	mask = __raw_readl(S3C2410_INTMSK);
+	mask |= 1UL << irqno;
+	__raw_writel(mask, S3C2410_INTMSK);
+}
+
+static inline void
+s3c_irq_ack(unsigned int irqno)
+{
+	unsigned long bitval = 1UL << (irqno - IRQ_EINT0);
+
+	__raw_writel(bitval, S3C2410_SRCPND);
+	__raw_writel(bitval, S3C2410_INTPND);
+}
+
+static inline void
+s3c_irq_maskack(unsigned int irqno)
+{
+	unsigned long bitval = 1UL << (irqno - IRQ_EINT0);
+	unsigned long mask;
+
+	mask = __raw_readl(S3C2410_INTMSK);
+	__raw_writel(mask|bitval, S3C2410_INTMSK);
+
+	__raw_writel(bitval, S3C2410_SRCPND);
+	__raw_writel(bitval, S3C2410_INTPND);
+}
+
+
+static void
+s3c_irq_unmask(unsigned int irqno)
+{
+	unsigned long mask;
+
+	if (irqno != IRQ_TIMER4 && irqno != IRQ_EINT8t23)
+		irqdbf2("s3c_irq_unmask %d\n", irqno);
+
+	irqno -= IRQ_EINT0;
+
+	mask = __raw_readl(S3C2410_INTMSK);
+	mask &= ~(1UL << irqno);
+	__raw_writel(mask, S3C2410_INTMSK);
+}
+
+struct irq_chip s3c_irq_level_chip = {
+	.name		= "s3c-level",
+	.ack		= s3c_irq_maskack,
+	.mask		= s3c_irq_mask,
+	.unmask		= s3c_irq_unmask,
+	.set_wake	= s3c_irq_wake
+};
+
+static struct irq_chip s3c_irq_chip = {
+	.name		= "s3c",
+	.ack		= s3c_irq_ack,
+	.mask		= s3c_irq_mask,
+	.unmask		= s3c_irq_unmask,
+	.set_wake	= s3c_irq_wake
+};
+
+static void
+s3c_irqext_mask(unsigned int irqno)
+{
+	unsigned long mask;
+
+	irqno -= EXTINT_OFF;
+
+	mask = __raw_readl(S3C24XX_EINTMASK);
+	mask |= ( 1UL << irqno);
+	__raw_writel(mask, S3C24XX_EINTMASK);
+}
+
+static void
+s3c_irqext_ack(unsigned int irqno)
+{
+	unsigned long req;
+	unsigned long bit;
+	unsigned long mask;
+
+	bit = 1UL << (irqno - EXTINT_OFF);
+
+	mask = __raw_readl(S3C24XX_EINTMASK);
+
+	__raw_writel(bit, S3C24XX_EINTPEND);
+
+	req = __raw_readl(S3C24XX_EINTPEND);
+	req &= ~mask;
+
+	/* not sure if we should be acking the parent irq... */
+
+	if (irqno <= IRQ_EINT7 ) {
+		if ((req & 0xf0) == 0)
+			s3c_irq_ack(IRQ_EINT4t7);
+	} else {
+		if ((req >> 8) == 0)
+			s3c_irq_ack(IRQ_EINT8t23);
+	}
+}
+
+static void
+s3c_irqext_unmask(unsigned int irqno)
+{
+	unsigned long mask;
+
+	irqno -= EXTINT_OFF;
+
+	mask = __raw_readl(S3C24XX_EINTMASK);
+	mask &= ~( 1UL << irqno);
+	__raw_writel(mask, S3C24XX_EINTMASK);
+}
+
+int
+s3c_irqext_type(unsigned int irq, unsigned int type)
+{
+	void __iomem *extint_reg;
+	void __iomem *gpcon_reg;
+	unsigned long gpcon_offset, extint_offset;
+	unsigned long newvalue = 0, value;
+
+	if ((irq >= IRQ_EINT0) && (irq <= IRQ_EINT3))
+	{
+		gpcon_reg = S3C2410_GPFCON;
+		extint_reg = S3C24XX_EXTINT0;
+		gpcon_offset = (irq - IRQ_EINT0) * 2;
+		extint_offset = (irq - IRQ_EINT0) * 4;
+	}
+	else if ((irq >= IRQ_EINT4) && (irq <= IRQ_EINT7))
+	{
+		gpcon_reg = S3C2410_GPFCON;
+		extint_reg = S3C24XX_EXTINT0;
+		gpcon_offset = (irq - (EXTINT_OFF)) * 2;
+		extint_offset = (irq - (EXTINT_OFF)) * 4;
+	}
+	else if ((irq >= IRQ_EINT8) && (irq <= IRQ_EINT15))
+	{
+		gpcon_reg = S3C2410_GPGCON;
+		extint_reg = S3C24XX_EXTINT1;
+		gpcon_offset = (irq - IRQ_EINT8) * 2;
+		extint_offset = (irq - IRQ_EINT8) * 4;
+	}
+	else if ((irq >= IRQ_EINT16) && (irq <= IRQ_EINT23))
+	{
+		gpcon_reg = S3C2410_GPGCON;
+		extint_reg = S3C24XX_EXTINT2;
+		gpcon_offset = (irq - IRQ_EINT8) * 2;
+		extint_offset = (irq - IRQ_EINT16) * 4;
+	} else
+		return -1;
+
+	/* Set the GPIO to external interrupt mode */
+	value = __raw_readl(gpcon_reg);
+	value = (value & ~(3 << gpcon_offset)) | (0x02 << gpcon_offset);
+	__raw_writel(value, gpcon_reg);
+
+	/* Set the external interrupt to pointed trigger type */
+	switch (type)
+	{
+		case IRQT_NOEDGE:
+			printk(KERN_WARNING "No edge setting!\n");
+			break;
+
+		case IRQT_RISING:
+			newvalue = S3C2410_EXTINT_RISEEDGE;
+			break;
+
+		case IRQT_FALLING:
+			newvalue = S3C2410_EXTINT_FALLEDGE;
+			break;
+
+		case IRQT_BOTHEDGE:
+			newvalue = S3C2410_EXTINT_BOTHEDGE;
+			break;
+
+		case IRQT_LOW:
+			newvalue = S3C2410_EXTINT_LOWLEV;
+			break;
+
+		case IRQT_HIGH:
+			newvalue = S3C2410_EXTINT_HILEV;
+			break;
+
+		default:
+			printk(KERN_ERR "No such irq type %d", type);
+			return -1;
+	}
+
+	value = __raw_readl(extint_reg);
+	value = (value & ~(7 << extint_offset)) | (newvalue << extint_offset);
+	__raw_writel(value, extint_reg);
+
+	return 0;
+}
+
+static struct irq_chip s3c_irqext_chip = {
+	.name		= "s3c-ext",
+	.mask		= s3c_irqext_mask,
+	.unmask		= s3c_irqext_unmask,
+	.ack		= s3c_irqext_ack,
+	.set_type	= s3c_irqext_type,
+	.set_wake	= s3c_irqext_wake
+};
+
+static struct irq_chip s3c_irq_eint0t4 = {
+	.name		= "s3c-ext0",
+	.ack		= s3c_irq_ack,
+	.mask		= s3c_irq_mask,
+	.unmask		= s3c_irq_unmask,
+	.set_wake	= s3c_irq_wake,
+	.set_type	= s3c_irqext_type,
+};
+
+/* mask values for the parent registers for each of the interrupt types */
+
+#define INTMSK_UART0	 (1UL << (IRQ_UART0 - IRQ_EINT0))
+#define INTMSK_UART1	 (1UL << (IRQ_UART1 - IRQ_EINT0))
+#define INTMSK_UART2	 (1UL << (IRQ_UART2 - IRQ_EINT0))
+#define INTMSK_ADCPARENT (1UL << (IRQ_ADCPARENT - IRQ_EINT0))
+
+
+/* UART0 */
+
+static void
+s3c_irq_uart0_mask(unsigned int irqno)
+{
+	s3c_irqsub_mask(irqno, INTMSK_UART0, 7);
+}
+
+static void
+s3c_irq_uart0_unmask(unsigned int irqno)
+{
+	s3c_irqsub_unmask(irqno, INTMSK_UART0);
+}
+
+static void
+s3c_irq_uart0_ack(unsigned int irqno)
+{
+	s3c_irqsub_maskack(irqno, INTMSK_UART0, 7);
+}
+
+static struct irq_chip s3c_irq_uart0 = {
+	.name		= "s3c-uart0",
+	.mask		= s3c_irq_uart0_mask,
+	.unmask		= s3c_irq_uart0_unmask,
+	.ack		= s3c_irq_uart0_ack,
+};
+
+/* UART1 */
+
+static void
+s3c_irq_uart1_mask(unsigned int irqno)
+{
+	s3c_irqsub_mask(irqno, INTMSK_UART1, 7 << 3);
+}
+
+static void
+s3c_irq_uart1_unmask(unsigned int irqno)
+{
+	s3c_irqsub_unmask(irqno, INTMSK_UART1);
+}
+
+static void
+s3c_irq_uart1_ack(unsigned int irqno)
+{
+	s3c_irqsub_maskack(irqno, INTMSK_UART1, 7 << 3);
+}
+
+static struct irq_chip s3c_irq_uart1 = {
+	.name		= "s3c-uart1",
+	.mask		= s3c_irq_uart1_mask,
+	.unmask		= s3c_irq_uart1_unmask,
+	.ack		= s3c_irq_uart1_ack,
+};
+
+/* UART2 */
+
+static void
+s3c_irq_uart2_mask(unsigned int irqno)
+{
+	s3c_irqsub_mask(irqno, INTMSK_UART2, 7 << 6);
+}
+
+static void
+s3c_irq_uart2_unmask(unsigned int irqno)
+{
+	s3c_irqsub_unmask(irqno, INTMSK_UART2);
+}
+
+static void
+s3c_irq_uart2_ack(unsigned int irqno)
+{
+	s3c_irqsub_maskack(irqno, INTMSK_UART2, 7 << 6);
+}
+
+static struct irq_chip s3c_irq_uart2 = {
+	.name		= "s3c-uart2",
+	.mask		= s3c_irq_uart2_mask,
+	.unmask		= s3c_irq_uart2_unmask,
+	.ack		= s3c_irq_uart2_ack,
+};
+
+/* ADC and Touchscreen */
+
+static void
+s3c_irq_adc_mask(unsigned int irqno)
+{
+	s3c_irqsub_mask(irqno, INTMSK_ADCPARENT, 3 << 9);
+}
+
+static void
+s3c_irq_adc_unmask(unsigned int irqno)
+{
+	s3c_irqsub_unmask(irqno, INTMSK_ADCPARENT);
+}
+
+static void
+s3c_irq_adc_ack(unsigned int irqno)
+{
+	s3c_irqsub_ack(irqno, INTMSK_ADCPARENT, 3 << 9);
+}
+
+static struct irq_chip s3c_irq_adc = {
+	.name		= "s3c-adc",
+	.mask		= s3c_irq_adc_mask,
+	.unmask		= s3c_irq_adc_unmask,
+	.ack		= s3c_irq_adc_ack,
+};
+
+/* irq demux for adc */
+static void s3c_irq_demux_adc(unsigned int irq,
+			      struct irq_desc *desc)
+{
+	unsigned int subsrc, submsk;
+	unsigned int offset = 9;
+	struct irq_desc *mydesc;
+
+	/* read the current pending interrupts, and the mask
+	 * for what it is available */
+
+	subsrc = __raw_readl(S3C2410_SUBSRCPND);
+	submsk = __raw_readl(S3C2410_INTSUBMSK);
+
+	subsrc &= ~submsk;
+	subsrc >>= offset;
+	subsrc &= 3;
+
+	if (subsrc != 0) {
+		if (subsrc & 1) {
+			mydesc = irq_desc + IRQ_TC;
+			desc_handle_irq(IRQ_TC, mydesc);
+		}
+		if (subsrc & 2) {
+			mydesc = irq_desc + IRQ_ADC;
+			desc_handle_irq(IRQ_ADC, mydesc);
+		}
+	}
+}
+
+static void s3c_irq_demux_uart(unsigned int start)
+{
+	unsigned int subsrc, submsk;
+	unsigned int offset = start - IRQ_S3CUART_RX0;
+	struct irq_desc *desc;
+
+	/* read the current pending interrupts, and the mask
+	 * for what it is available */
+
+	subsrc = __raw_readl(S3C2410_SUBSRCPND);
+	submsk = __raw_readl(S3C2410_INTSUBMSK);
+
+	irqdbf2("s3c_irq_demux_uart: start=%d (%d), subsrc=0x%08x,0x%08x\n",
+		start, offset, subsrc, submsk);
+
+	subsrc &= ~submsk;
+	subsrc >>= offset;
+	subsrc &= 7;
+
+	if (subsrc != 0) {
+		desc = irq_desc + start;
+
+		if (subsrc & 1)
+			desc_handle_irq(start, desc);
+
+		desc++;
+
+		if (subsrc & 2)
+			desc_handle_irq(start+1, desc);
+
+		desc++;
+
+		if (subsrc & 4)
+			desc_handle_irq(start+2, desc);
+	}
+}
+
+/* uart demux entry points */
+
+static void
+s3c_irq_demux_uart0(unsigned int irq,
+		    struct irq_desc *desc)
+{
+	irq = irq;
+	s3c_irq_demux_uart(IRQ_S3CUART_RX0);
+}
+
+static void
+s3c_irq_demux_uart1(unsigned int irq,
+		    struct irq_desc *desc)
+{
+	irq = irq;
+	s3c_irq_demux_uart(IRQ_S3CUART_RX1);
+}
+
+static void
+s3c_irq_demux_uart2(unsigned int irq,
+		    struct irq_desc *desc)
+{
+	irq = irq;
+	s3c_irq_demux_uart(IRQ_S3CUART_RX2);
+}
+
+static void
+s3c_irq_demux_extint8(unsigned int irq,
+		      struct irq_desc *desc)
+{
+	unsigned long eintpnd = __raw_readl(S3C24XX_EINTPEND);
+	unsigned long eintmsk = __raw_readl(S3C24XX_EINTMASK);
+
+	eintpnd &= ~eintmsk;
+	eintpnd &= ~0xff;	/* ignore lower irqs */
+
+	/* we may as well handle all the pending IRQs here */
+
+	while (eintpnd) {
+		irq = __ffs(eintpnd);
+		eintpnd &= ~(1<<irq);
+
+		irq += (IRQ_EINT4 - 4);
+		desc_handle_irq(irq, irq_desc + irq);
+	}
+
+}
+
+static void
+s3c_irq_demux_extint4t7(unsigned int irq,
+			struct irq_desc *desc)
+{
+	unsigned long eintpnd = __raw_readl(S3C24XX_EINTPEND);
+	unsigned long eintmsk = __raw_readl(S3C24XX_EINTMASK);
+
+	eintpnd &= ~eintmsk;
+	eintpnd &= 0xff;	/* only lower irqs */
+
+	/* we may as well handle all the pending IRQs here */
+
+	while (eintpnd) {
+		irq = __ffs(eintpnd);
+		eintpnd &= ~(1<<irq);
+
+		irq += (IRQ_EINT4 - 4);
+
+		desc_handle_irq(irq, irq_desc + irq);
+	}
+}
+
+#ifdef CONFIG_PM
+
+static struct sleep_save irq_save[] = {
+	SAVE_ITEM(S3C2410_INTMSK),
+	SAVE_ITEM(S3C2410_INTSUBMSK),
+};
+
+/* the extint values move between the s3c2410/s3c2440 and the s3c2412
+ * so we use an array to hold them, and to calculate the address of
+ * the register at run-time
+*/
+
+static unsigned long save_extint[3];
+static unsigned long save_eintflt[4];
+static unsigned long save_eintmask;
+
+int s3c24xx_irq_suspend(struct sys_device *dev, pm_message_t state)
+{
+	unsigned int i;
+
+	for (i = 0; i < ARRAY_SIZE(save_extint); i++)
+		save_extint[i] = __raw_readl(S3C24XX_EXTINT0 + (i*4));
+
+	for (i = 0; i < ARRAY_SIZE(save_eintflt); i++)
+		save_eintflt[i] = __raw_readl(S3C24XX_EINFLT0 + (i*4));
+
+	s3c2410_pm_do_save(irq_save, ARRAY_SIZE(irq_save));
+	save_eintmask = __raw_readl(S3C24XX_EINTMASK);
+
+	return 0;
+}
+
+int s3c24xx_irq_resume(struct sys_device *dev)
+{
+	unsigned int i;
+
+	for (i = 0; i < ARRAY_SIZE(save_extint); i++)
+		__raw_writel(save_extint[i], S3C24XX_EXTINT0 + (i*4));
+
+	for (i = 0; i < ARRAY_SIZE(save_eintflt); i++)
+		__raw_writel(save_eintflt[i], S3C24XX_EINFLT0 + (i*4));
+
+	s3c2410_pm_do_restore(irq_save, ARRAY_SIZE(irq_save));
+	__raw_writel(save_eintmask, S3C24XX_EINTMASK);
+
+	return 0;
+}
+
+#else
+#define s3c24xx_irq_suspend NULL
+#define s3c24xx_irq_resume  NULL
+#endif
+
+/* s3c24xx_init_irq
+ *
+ * Initialise S3C2410 IRQ system
+*/
+
+void __init s3c24xx_init_irq(void)
+{
+	unsigned long pend;
+	unsigned long last;
+	int irqno;
+	int i;
+
+	irqdbf("s3c2410_init_irq: clearing interrupt status flags\n");
+
+	/* first, clear all interrupts pending... */
+
+	last = 0;
+	for (i = 0; i < 4; i++) {
+		pend = __raw_readl(S3C24XX_EINTPEND);
+
+		if (pend == 0 || pend == last)
+			break;
+
+		__raw_writel(pend, S3C24XX_EINTPEND);
+		printk("irq: clearing pending ext status %08x\n", (int)pend);
+		last = pend;
+	}
+
+	last = 0;
+	for (i = 0; i < 4; i++) {
+		pend = __raw_readl(S3C2410_INTPND);
+
+		if (pend == 0 || pend == last)
+			break;
+
+		__raw_writel(pend, S3C2410_SRCPND);
+		__raw_writel(pend, S3C2410_INTPND);
+		printk("irq: clearing pending status %08x\n", (int)pend);
+		last = pend;
+	}
+
+	last = 0;
+	for (i = 0; i < 4; i++) {
+		pend = __raw_readl(S3C2410_SUBSRCPND);
+
+		if (pend == 0 || pend == last)
+			break;
+
+		printk("irq: clearing subpending status %08x\n", (int)pend);
+		__raw_writel(pend, S3C2410_SUBSRCPND);
+		last = pend;
+	}
+
+	/* register the main interrupts */
+
+	irqdbf("s3c2410_init_irq: registering s3c2410 interrupt handlers\n");
+
+	for (irqno = IRQ_EINT4t7; irqno <= IRQ_ADCPARENT; irqno++) {
+		/* set all the s3c2410 internal irqs */
+
+		switch (irqno) {
+			/* deal with the special IRQs (cascaded) */
+
+		case IRQ_EINT4t7:
+		case IRQ_EINT8t23:
+		case IRQ_UART0:
+		case IRQ_UART1:
+		case IRQ_UART2:
+		case IRQ_ADCPARENT:
+			set_irq_chip(irqno, &s3c_irq_level_chip);
+			set_irq_handler(irqno, handle_level_irq);
+			break;
+
+		case IRQ_RESERVED6:
+		case IRQ_RESERVED24:
+			/* no IRQ here */
+			break;
+
+		default:
+			//irqdbf("registering irq %d (s3c irq)\n", irqno);
+			set_irq_chip(irqno, &s3c_irq_chip);
+			set_irq_handler(irqno, handle_edge_irq);
+			set_irq_flags(irqno, IRQF_VALID);
+		}
+	}
+
+	/* setup the cascade irq handlers */
+
+	set_irq_chained_handler(IRQ_EINT4t7, s3c_irq_demux_extint4t7);
+	set_irq_chained_handler(IRQ_EINT8t23, s3c_irq_demux_extint8);
+
+	set_irq_chained_handler(IRQ_UART0, s3c_irq_demux_uart0);
+	set_irq_chained_handler(IRQ_UART1, s3c_irq_demux_uart1);
+	set_irq_chained_handler(IRQ_UART2, s3c_irq_demux_uart2);
+	set_irq_chained_handler(IRQ_ADCPARENT, s3c_irq_demux_adc);
+
+	/* external interrupts */
+
+	for (irqno = IRQ_EINT0; irqno <= IRQ_EINT3; irqno++) {
+		irqdbf("registering irq %d (ext int)\n", irqno);
+		set_irq_chip(irqno, &s3c_irq_eint0t4);
+		set_irq_handler(irqno, handle_edge_irq);
+		set_irq_flags(irqno, IRQF_VALID);
+	}
+
+	for (irqno = IRQ_EINT4; irqno <= IRQ_EINT23; irqno++) {
+		irqdbf("registering irq %d (extended s3c irq)\n", irqno);
+		set_irq_chip(irqno, &s3c_irqext_chip);
+		set_irq_handler(irqno, handle_edge_irq);
+		set_irq_flags(irqno, IRQF_VALID);
+	}
+
+	/* register the uart interrupts */
+
+	irqdbf("s3c2410: registering external interrupts\n");
+
+	for (irqno = IRQ_S3CUART_RX0; irqno <= IRQ_S3CUART_ERR0; irqno++) {
+		irqdbf("registering irq %d (s3c uart0 irq)\n", irqno);
+		set_irq_chip(irqno, &s3c_irq_uart0);
+		set_irq_handler(irqno, handle_level_irq);
+		set_irq_flags(irqno, IRQF_VALID);
+	}
+
+	for (irqno = IRQ_S3CUART_RX1; irqno <= IRQ_S3CUART_ERR1; irqno++) {
+		irqdbf("registering irq %d (s3c uart1 irq)\n", irqno);
+		set_irq_chip(irqno, &s3c_irq_uart1);
+		set_irq_handler(irqno, handle_level_irq);
+		set_irq_flags(irqno, IRQF_VALID);
+	}
+
+	for (irqno = IRQ_S3CUART_RX2; irqno <= IRQ_S3CUART_ERR2; irqno++) {
+		irqdbf("registering irq %d (s3c uart2 irq)\n", irqno);
+		set_irq_chip(irqno, &s3c_irq_uart2);
+		set_irq_handler(irqno, handle_level_irq);
+		set_irq_flags(irqno, IRQF_VALID);
+	}
+
+	for (irqno = IRQ_TC; irqno <= IRQ_ADC; irqno++) {
+		irqdbf("registering irq %d (s3c adc irq)\n", irqno);
+		set_irq_chip(irqno, &s3c_irq_adc);
+		set_irq_handler(irqno, handle_edge_irq);
+		set_irq_flags(irqno, IRQF_VALID);
+	}
+
+	irqdbf("s3c2410: registered interrupt handlers\n");
+}
diff --git a/arch/arm/mach-s3c2410/pm-simtec.c b/arch/arm/plat-s3c24xx/pm-simtec.c
index 619133eb716..bd965f2feec 100644
--- a/arch/arm/mach-s3c2410/pm-simtec.c
+++ b/arch/arm/plat-s3c24xx/pm-simtec.c
@@ -1,4 +1,4 @@
-/* linux/arch/arm/mach-s3c2410/pm-simtec.c
+/* linux/arch/arm/plat-s3c24xx/pm-simtec.c
  *
  * Copyright (c) 2004 Simtec Electronics
  *	Ben Dooks <ben@simtec.co.uk>
@@ -32,7 +32,7 @@
 
 #include <asm/mach-types.h>
 
-#include "pm.h"
+#include <asm/plat-s3c24xx/pm.h>
 
 #define COPYRIGHT ", (c) 2005 Simtec Electronics"
 
diff --git a/arch/arm/plat-s3c24xx/pm.c b/arch/arm/plat-s3c24xx/pm.c
new file mode 100644
index 00000000000..ecf68d61190
--- /dev/null
+++ b/arch/arm/plat-s3c24xx/pm.c
@@ -0,0 +1,659 @@
+/* linux/arch/arm/plat-s3c24xx/pm.c
+ *
+ * Copyright (c) 2004,2006 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C24XX Power Manager (Suspend-To-RAM) support
+ *
+ * See Documentation/arm/Samsung-S3C24XX/Suspend.txt for more information
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ *
+ * Parts based on arch/arm/mach-pxa/pm.c
+ *
+ * Thanks to Dimitry Andric for debugging
+*/
+
+#include <linux/init.h>
+#include <linux/suspend.h>
+#include <linux/errno.h>
+#include <linux/time.h>
+#include <linux/interrupt.h>
+#include <linux/crc32.h>
+#include <linux/ioport.h>
+#include <linux/delay.h>
+#include <linux/serial_core.h>
+
+#include <asm/cacheflush.h>
+#include <asm/hardware.h>
+#include <asm/io.h>
+
+#include <asm/arch/regs-serial.h>
+#include <asm/arch/regs-clock.h>
+#include <asm/arch/regs-gpio.h>
+#include <asm/arch/regs-mem.h>
+#include <asm/arch/regs-irq.h>
+
+#include <asm/mach/time.h>
+
+#include <asm/plat-s3c24xx/pm.h>
+
+/* for external use */
+
+unsigned long s3c_pm_flags;
+
+#define PFX "s3c24xx-pm: "
+
+static struct sleep_save core_save[] = {
+	SAVE_ITEM(S3C2410_LOCKTIME),
+	SAVE_ITEM(S3C2410_CLKCON),
+
+	/* we restore the timings here, with the proviso that the board
+	 * brings the system up in an slower, or equal frequency setting
+	 * to the original system.
+	 *
+	 * if we cannot guarantee this, then things are going to go very
+	 * wrong here, as we modify the refresh and both pll settings.
+	 */
+
+	SAVE_ITEM(S3C2410_BWSCON),
+	SAVE_ITEM(S3C2410_BANKCON0),
+	SAVE_ITEM(S3C2410_BANKCON1),
+	SAVE_ITEM(S3C2410_BANKCON2),
+	SAVE_ITEM(S3C2410_BANKCON3),
+	SAVE_ITEM(S3C2410_BANKCON4),
+	SAVE_ITEM(S3C2410_BANKCON5),
+
+	SAVE_ITEM(S3C2410_CLKDIVN),
+	SAVE_ITEM(S3C2410_MPLLCON),
+	SAVE_ITEM(S3C2410_UPLLCON),
+	SAVE_ITEM(S3C2410_CLKSLOW),
+	SAVE_ITEM(S3C2410_REFRESH),
+};
+
+static struct sleep_save gpio_save[] = {
+	SAVE_ITEM(S3C2410_GPACON),
+	SAVE_ITEM(S3C2410_GPADAT),
+
+	SAVE_ITEM(S3C2410_GPBCON),
+	SAVE_ITEM(S3C2410_GPBDAT),
+	SAVE_ITEM(S3C2410_GPBUP),
+
+	SAVE_ITEM(S3C2410_GPCCON),
+	SAVE_ITEM(S3C2410_GPCDAT),
+	SAVE_ITEM(S3C2410_GPCUP),
+
+	SAVE_ITEM(S3C2410_GPDCON),
+	SAVE_ITEM(S3C2410_GPDDAT),
+	SAVE_ITEM(S3C2410_GPDUP),
+
+	SAVE_ITEM(S3C2410_GPECON),
+	SAVE_ITEM(S3C2410_GPEDAT),
+	SAVE_ITEM(S3C2410_GPEUP),
+
+	SAVE_ITEM(S3C2410_GPFCON),
+	SAVE_ITEM(S3C2410_GPFDAT),
+	SAVE_ITEM(S3C2410_GPFUP),
+
+	SAVE_ITEM(S3C2410_GPGCON),
+	SAVE_ITEM(S3C2410_GPGDAT),
+	SAVE_ITEM(S3C2410_GPGUP),
+
+	SAVE_ITEM(S3C2410_GPHCON),
+	SAVE_ITEM(S3C2410_GPHDAT),
+	SAVE_ITEM(S3C2410_GPHUP),
+
+	SAVE_ITEM(S3C2410_DCLKCON),
+};
+
+#ifdef CONFIG_S3C2410_PM_DEBUG
+
+#define SAVE_UART(va) \
+	SAVE_ITEM((va) + S3C2410_ULCON), \
+	SAVE_ITEM((va) + S3C2410_UCON), \
+	SAVE_ITEM((va) + S3C2410_UFCON), \
+	SAVE_ITEM((va) + S3C2410_UMCON), \
+	SAVE_ITEM((va) + S3C2410_UBRDIV)
+
+static struct sleep_save uart_save[] = {
+	SAVE_UART(S3C24XX_VA_UART0),
+	SAVE_UART(S3C24XX_VA_UART1),
+#ifndef CONFIG_CPU_S3C2400
+	SAVE_UART(S3C24XX_VA_UART2),
+#endif
+};
+
+/* debug
+ *
+ * we send the debug to printascii() to allow it to be seen if the
+ * system never wakes up from the sleep
+*/
+
+extern void printascii(const char *);
+
+void pm_dbg(const char *fmt, ...)
+{
+	va_list va;
+	char buff[256];
+
+	va_start(va, fmt);
+	vsprintf(buff, fmt, va);
+	va_end(va);
+
+	printascii(buff);
+}
+
+static void s3c2410_pm_debug_init(void)
+{
+	unsigned long tmp = __raw_readl(S3C2410_CLKCON);
+
+	/* re-start uart clocks */
+	tmp |= S3C2410_CLKCON_UART0;
+	tmp |= S3C2410_CLKCON_UART1;
+	tmp |= S3C2410_CLKCON_UART2;
+
+	__raw_writel(tmp, S3C2410_CLKCON);
+	udelay(10);
+}
+
+#define DBG(fmt...) pm_dbg(fmt)
+#else
+#define DBG(fmt...) printk(KERN_DEBUG fmt)
+
+#define s3c2410_pm_debug_init() do { } while(0)
+
+static struct sleep_save uart_save[] = {};
+#endif
+
+#if defined(CONFIG_S3C2410_PM_CHECK) && CONFIG_S3C2410_PM_CHECK_CHUNKSIZE != 0
+
+/* suspend checking code...
+ *
+ * this next area does a set of crc checks over all the installed
+ * memory, so the system can verify if the resume was ok.
+ *
+ * CONFIG_S3C2410_PM_CHECK_CHUNKSIZE defines the block-size for the CRC,
+ * increasing it will mean that the area corrupted will be less easy to spot,
+ * and reducing the size will cause the CRC save area to grow
+*/
+
+#define CHECK_CHUNKSIZE (CONFIG_S3C2410_PM_CHECK_CHUNKSIZE * 1024)
+
+static u32 crc_size;	/* size needed for the crc block */
+static u32 *crcs;	/* allocated over suspend/resume */
+
+typedef u32 *(run_fn_t)(struct resource *ptr, u32 *arg);
+
+/* s3c2410_pm_run_res
+ *
+ * go thorugh the given resource list, and look for system ram
+*/
+
+static void s3c2410_pm_run_res(struct resource *ptr, run_fn_t fn, u32 *arg)
+{
+	while (ptr != NULL) {
+		if (ptr->child != NULL)
+			s3c2410_pm_run_res(ptr->child, fn, arg);
+
+		if ((ptr->flags & IORESOURCE_MEM) &&
+		    strcmp(ptr->name, "System RAM") == 0) {
+			DBG("Found system RAM at %08lx..%08lx\n",
+			    ptr->start, ptr->end);
+			arg = (fn)(ptr, arg);
+		}
+
+		ptr = ptr->sibling;
+	}
+}
+
+static void s3c2410_pm_run_sysram(run_fn_t fn, u32 *arg)
+{
+	s3c2410_pm_run_res(&iomem_resource, fn, arg);
+}
+
+static u32 *s3c2410_pm_countram(struct resource *res, u32 *val)
+{
+	u32 size = (u32)(res->end - res->start)+1;
+
+	size += CHECK_CHUNKSIZE-1;
+	size /= CHECK_CHUNKSIZE;
+
+	DBG("Area %08lx..%08lx, %d blocks\n", res->start, res->end, size);
+
+	*val += size * sizeof(u32);
+	return val;
+}
+
+/* s3c2410_pm_prepare_check
+ *
+ * prepare the necessary information for creating the CRCs. This
+ * must be done before the final save, as it will require memory
+ * allocating, and thus touching bits of the kernel we do not
+ * know about.
+*/
+
+static void s3c2410_pm_check_prepare(void)
+{
+	crc_size = 0;
+
+	s3c2410_pm_run_sysram(s3c2410_pm_countram, &crc_size);
+
+	DBG("s3c2410_pm_prepare_check: %u checks needed\n", crc_size);
+
+	crcs = kmalloc(crc_size+4, GFP_KERNEL);
+	if (crcs == NULL)
+		printk(KERN_ERR "Cannot allocated CRC save area\n");
+}
+
+static u32 *s3c2410_pm_makecheck(struct resource *res, u32 *val)
+{
+	unsigned long addr, left;
+
+	for (addr = res->start; addr < res->end;
+	     addr += CHECK_CHUNKSIZE) {
+		left = res->end - addr;
+
+		if (left > CHECK_CHUNKSIZE)
+			left = CHECK_CHUNKSIZE;
+
+		*val = crc32_le(~0, phys_to_virt(addr), left);
+		val++;
+	}
+
+	return val;
+}
+
+/* s3c2410_pm_check_store
+ *
+ * compute the CRC values for the memory blocks before the final
+ * sleep.
+*/
+
+static void s3c2410_pm_check_store(void)
+{
+	if (crcs != NULL)
+		s3c2410_pm_run_sysram(s3c2410_pm_makecheck, crcs);
+}
+
+/* in_region
+ *
+ * return TRUE if the area defined by ptr..ptr+size contatins the
+ * what..what+whatsz
+*/
+
+static inline int in_region(void *ptr, int size, void *what, size_t whatsz)
+{
+	if ((what+whatsz) < ptr)
+		return 0;
+
+	if (what > (ptr+size))
+		return 0;
+
+	return 1;
+}
+
+static u32 *s3c2410_pm_runcheck(struct resource *res, u32 *val)
+{
+	void *save_at = phys_to_virt(s3c2410_sleep_save_phys);
+	unsigned long addr;
+	unsigned long left;
+	void *ptr;
+	u32 calc;
+
+	for (addr = res->start; addr < res->end;
+	     addr += CHECK_CHUNKSIZE) {
+		left = res->end - addr;
+
+		if (left > CHECK_CHUNKSIZE)
+			left = CHECK_CHUNKSIZE;
+
+		ptr = phys_to_virt(addr);
+
+		if (in_region(ptr, left, crcs, crc_size)) {
+			DBG("skipping %08lx, has crc block in\n", addr);
+			goto skip_check;
+		}
+
+		if (in_region(ptr, left, save_at, 32*4 )) {
+			DBG("skipping %08lx, has save block in\n", addr);
+			goto skip_check;
+		}
+
+		/* calculate and check the checksum */
+
+		calc = crc32_le(~0, ptr, left);
+		if (calc != *val) {
+			printk(KERN_ERR PFX "Restore CRC error at "
+			       "%08lx (%08x vs %08x)\n", addr, calc, *val);
+
+			DBG("Restore CRC error at %08lx (%08x vs %08x)\n",
+			    addr, calc, *val);
+		}
+
+	skip_check:
+		val++;
+	}
+
+	return val;
+}
+
+/* s3c2410_pm_check_restore
+ *
+ * check the CRCs after the restore event and free the memory used
+ * to hold them
+*/
+
+static void s3c2410_pm_check_restore(void)
+{
+	if (crcs != NULL) {
+		s3c2410_pm_run_sysram(s3c2410_pm_runcheck, crcs);
+		kfree(crcs);
+		crcs = NULL;
+	}
+}
+
+#else
+
+#define s3c2410_pm_check_prepare() do { } while(0)
+#define s3c2410_pm_check_restore() do { } while(0)
+#define s3c2410_pm_check_store()   do { } while(0)
+#endif
+
+/* helper functions to save and restore register state */
+
+void s3c2410_pm_do_save(struct sleep_save *ptr, int count)
+{
+	for (; count > 0; count--, ptr++) {
+		ptr->val = __raw_readl(ptr->reg);
+		DBG("saved %p value %08lx\n", ptr->reg, ptr->val);
+	}
+}
+
+/* s3c2410_pm_do_restore
+ *
+ * restore the system from the given list of saved registers
+ *
+ * Note, we do not use DBG() in here, as the system may not have
+ * restore the UARTs state yet
+*/
+
+void s3c2410_pm_do_restore(struct sleep_save *ptr, int count)
+{
+	for (; count > 0; count--, ptr++) {
+		printk(KERN_DEBUG "restore %p (restore %08lx, was %08x)\n",
+		       ptr->reg, ptr->val, __raw_readl(ptr->reg));
+
+		__raw_writel(ptr->val, ptr->reg);
+	}
+}
+
+/* s3c2410_pm_do_restore_core
+ *
+ * similar to s3c2410_pm_do_restore_core
+ *
+ * WARNING: Do not put any debug in here that may effect memory or use
+ * peripherals, as things may be changing!
+*/
+
+static void s3c2410_pm_do_restore_core(struct sleep_save *ptr, int count)
+{
+	for (; count > 0; count--, ptr++) {
+		__raw_writel(ptr->val, ptr->reg);
+	}
+}
+
+/* s3c2410_pm_show_resume_irqs
+ *
+ * print any IRQs asserted at resume time (ie, we woke from)
+*/
+
+static void s3c2410_pm_show_resume_irqs(int start, unsigned long which,
+					unsigned long mask)
+{
+	int i;
+
+	which &= ~mask;
+
+	for (i = 0; i <= 31; i++) {
+		if ((which) & (1L<<i)) {
+			DBG("IRQ %d asserted at resume\n", start+i);
+		}
+	}
+}
+
+/* s3c2410_pm_check_resume_pin
+ *
+ * check to see if the pin is configured correctly for sleep mode, and
+ * make any necessary adjustments if it is not
+*/
+
+static void s3c2410_pm_check_resume_pin(unsigned int pin, unsigned int irqoffs)
+{
+	unsigned long irqstate;
+	unsigned long pinstate;
+	int irq = s3c2410_gpio_getirq(pin);
+
+	if (irqoffs < 4)
+		irqstate = s3c_irqwake_intmask & (1L<<irqoffs);
+	else
+		irqstate = s3c_irqwake_eintmask & (1L<<irqoffs);
+
+	pinstate = s3c2410_gpio_getcfg(pin);
+
+	if (!irqstate) {
+		if (pinstate == S3C2410_GPIO_IRQ)
+			DBG("Leaving IRQ %d (pin %d) enabled\n", irq, pin);
+	} else {
+		if (pinstate == S3C2410_GPIO_IRQ) {
+			DBG("Disabling IRQ %d (pin %d)\n", irq, pin);
+			s3c2410_gpio_cfgpin(pin, S3C2410_GPIO_INPUT);
+		}
+	}
+}
+
+/* s3c2410_pm_configure_extint
+ *
+ * configure all external interrupt pins
+*/
+
+static void s3c2410_pm_configure_extint(void)
+{
+	int pin;
+
+	/* for each of the external interrupts (EINT0..EINT15) we
+	 * need to check wether it is an external interrupt source,
+	 * and then configure it as an input if it is not
+	*/
+
+	for (pin = S3C2410_GPF0; pin <= S3C2410_GPF7; pin++) {
+		s3c2410_pm_check_resume_pin(pin, pin - S3C2410_GPF0);
+	}
+
+	for (pin = S3C2410_GPG0; pin <= S3C2410_GPG7; pin++) {
+		s3c2410_pm_check_resume_pin(pin, (pin - S3C2410_GPG0)+8);
+	}
+}
+
+void (*pm_cpu_prep)(void);
+void (*pm_cpu_sleep)(void);
+
+#define any_allowed(mask, allow) (((mask) & (allow)) != (allow))
+
+/* s3c2410_pm_enter
+ *
+ * central control for sleep/resume process
+*/
+
+static int s3c2410_pm_enter(suspend_state_t state)
+{
+	unsigned long regs_save[16];
+
+	/* ensure the debug is initialised (if enabled) */
+
+	s3c2410_pm_debug_init();
+
+	DBG("s3c2410_pm_enter(%d)\n", state);
+
+	if (pm_cpu_prep == NULL || pm_cpu_sleep == NULL) {
+		printk(KERN_ERR PFX "error: no cpu sleep functions set\n");
+		return -EINVAL;
+	}
+
+	if (state != PM_SUSPEND_MEM) {
+		printk(KERN_ERR PFX "error: only PM_SUSPEND_MEM supported\n");
+		return -EINVAL;
+	}
+
+	/* check if we have anything to wake-up with... bad things seem
+	 * to happen if you suspend with no wakeup (system will often
+	 * require a full power-cycle)
+	*/
+
+	if (!any_allowed(s3c_irqwake_intmask, s3c_irqwake_intallow) &&
+	    !any_allowed(s3c_irqwake_eintmask, s3c_irqwake_eintallow)) {
+		printk(KERN_ERR PFX "No sources enabled for wake-up!\n");
+		printk(KERN_ERR PFX "Aborting sleep\n");
+		return -EINVAL;
+	}
+
+	/* prepare check area if configured */
+
+	s3c2410_pm_check_prepare();
+
+	/* store the physical address of the register recovery block */
+
+	s3c2410_sleep_save_phys = virt_to_phys(regs_save);
+
+	DBG("s3c2410_sleep_save_phys=0x%08lx\n", s3c2410_sleep_save_phys);
+
+	/* save all necessary core registers not covered by the drivers */
+
+	s3c2410_pm_do_save(gpio_save, ARRAY_SIZE(gpio_save));
+	s3c2410_pm_do_save(core_save, ARRAY_SIZE(core_save));
+	s3c2410_pm_do_save(uart_save, ARRAY_SIZE(uart_save));
+
+	/* set the irq configuration for wake */
+
+	s3c2410_pm_configure_extint();
+
+	DBG("sleep: irq wakeup masks: %08lx,%08lx\n",
+	    s3c_irqwake_intmask, s3c_irqwake_eintmask);
+
+	__raw_writel(s3c_irqwake_intmask, S3C2410_INTMSK);
+	__raw_writel(s3c_irqwake_eintmask, S3C2410_EINTMASK);
+
+	/* ack any outstanding external interrupts before we go to sleep */
+
+	__raw_writel(__raw_readl(S3C2410_EINTPEND), S3C2410_EINTPEND);
+	__raw_writel(__raw_readl(S3C2410_INTPND), S3C2410_INTPND);
+	__raw_writel(__raw_readl(S3C2410_SRCPND), S3C2410_SRCPND);
+
+	/* call cpu specific preperation */
+
+	pm_cpu_prep();
+
+	/* flush cache back to ram */
+
+	flush_cache_all();
+
+	s3c2410_pm_check_store();
+
+	/* send the cpu to sleep... */
+
+	__raw_writel(0x00, S3C2410_CLKCON);  /* turn off clocks over sleep */
+
+	/* s3c2410_cpu_save will also act as our return point from when
+	 * we resume as it saves its own register state, so use the return
+	 * code to differentiate return from save and return from sleep */
+
+	if (s3c2410_cpu_save(regs_save) == 0) {
+		flush_cache_all();
+		pm_cpu_sleep();
+	}
+
+	/* restore the cpu state */
+
+	cpu_init();
+
+	/* restore the system state */
+
+	s3c2410_pm_do_restore_core(core_save, ARRAY_SIZE(core_save));
+	s3c2410_pm_do_restore(gpio_save, ARRAY_SIZE(gpio_save));
+	s3c2410_pm_do_restore(uart_save, ARRAY_SIZE(uart_save));
+
+	s3c2410_pm_debug_init();
+
+	/* check what irq (if any) restored the system */
+
+	DBG("post sleep: IRQs 0x%08x, 0x%08x\n",
+	    __raw_readl(S3C2410_SRCPND),
+	    __raw_readl(S3C2410_EINTPEND));
+
+	s3c2410_pm_show_resume_irqs(IRQ_EINT0, __raw_readl(S3C2410_SRCPND),
+				    s3c_irqwake_intmask);
+
+	s3c2410_pm_show_resume_irqs(IRQ_EINT4-4, __raw_readl(S3C2410_EINTPEND),
+				    s3c_irqwake_eintmask);
+
+	DBG("post sleep, preparing to return\n");
+
+	s3c2410_pm_check_restore();
+
+	/* ok, let's return from sleep */
+
+	DBG("S3C2410 PM Resume (post-restore)\n");
+	return 0;
+}
+
+/*
+ * Called after processes are frozen, but before we shut down devices.
+ */
+static int s3c2410_pm_prepare(suspend_state_t state)
+{
+	return 0;
+}
+
+/*
+ * Called after devices are re-setup, but before processes are thawed.
+ */
+static int s3c2410_pm_finish(suspend_state_t state)
+{
+	return 0;
+}
+
+/*
+ * Set to PM_DISK_FIRMWARE so we can quickly veto suspend-to-disk.
+ */
+static struct pm_ops s3c2410_pm_ops = {
+	.pm_disk_mode	= PM_DISK_FIRMWARE,
+	.prepare	= s3c2410_pm_prepare,
+	.enter		= s3c2410_pm_enter,
+	.finish		= s3c2410_pm_finish,
+};
+
+/* s3c2410_pm_init
+ *
+ * Attach the power management functions. This should be called
+ * from the board specific initialisation if the board supports
+ * it.
+*/
+
+int __init s3c2410_pm_init(void)
+{
+	printk("S3C2410 Power Management, (c) 2004 Simtec Electronics\n");
+
+	pm_set_ops(&s3c2410_pm_ops);
+	return 0;
+}
diff --git a/arch/arm/mach-s3c2410/s3c244x-irq.c b/arch/arm/plat-s3c24xx/s3c244x-irq.c
index ede94636a72..a0e39d89401 100644
--- a/arch/arm/mach-s3c2410/s3c244x-irq.c
+++ b/arch/arm/plat-s3c24xx/s3c244x-irq.c
@@ -1,4 +1,4 @@
-/* linux/arch/arm/mach-s3c2410/s3c244x-irq.c
+/* linux/arch/arm/plat-s3c24xx/s3c244x-irq.c
  *
  * Copyright (c) 2003,2004 Simtec Electronics
  *	Ben Dooks <ben@simtec.co.uk>
@@ -35,9 +35,9 @@
 #include <asm/arch/regs-irq.h>
 #include <asm/arch/regs-gpio.h>
 
-#include "cpu.h"
-#include "pm.h"
-#include "irq.h"
+#include <asm/plat-s3c24xx/cpu.h>
+#include <asm/plat-s3c24xx/pm.h>
+#include <asm/plat-s3c24xx/irq.h>
 
 /* camera irq */
 
diff --git a/arch/arm/mach-s3c2410/s3c244x.c b/arch/arm/plat-s3c24xx/s3c244x.c
index 23c7494ad10..767f2e9a3a5 100644
--- a/arch/arm/mach-s3c2410/s3c244x.c
+++ b/arch/arm/plat-s3c24xx/s3c244x.c
@@ -1,9 +1,9 @@
-/* linux/arch/arm/mach-s3c2410/s3c244x.c
+/* linux/arch/arm/plat-s3c24xx/s3c244x.c
  *
  * Copyright (c) 2004-2006 Simtec Electronics
  *   Ben Dooks <ben@simtec.co.uk>
  *
- * Samsung S3C2440 and S3C2442 Mobile CPU support
+ * Samsung S3C2440 and S3C2442 Mobile CPU support (not S3C2443)
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
@@ -35,13 +35,13 @@
 #include <asm/arch/regs-gpioj.h>
 #include <asm/arch/regs-dsc.h>
 
-#include "s3c2410.h"
-#include "s3c2440.h"
+#include <asm/plat-s3c24xx/s3c2410.h>
+#include <asm/plat-s3c24xx/s3c2440.h>
 #include "s3c244x.h"
-#include "clock.h"
-#include "devs.h"
-#include "cpu.h"
-#include "pm.h"
+#include <asm/plat-s3c24xx/clock.h>
+#include <asm/plat-s3c24xx/devs.h>
+#include <asm/plat-s3c24xx/cpu.h>
+#include <asm/plat-s3c24xx/pm.h>
 
 static struct map_desc s3c244x_iodesc[] __initdata = {
 	IODESC_ENT(CLKPWR),
diff --git a/arch/arm/mach-s3c2410/s3c244x.h b/arch/arm/plat-s3c24xx/s3c244x.h
index 1488c1eb37e..f8ed17676a3 100644
--- a/arch/arm/mach-s3c2410/s3c244x.h
+++ b/arch/arm/plat-s3c24xx/s3c244x.h
@@ -1,4 +1,4 @@
-/* arch/arm/mach-s3c2410/s3c244x.h
+/* linux/arch/arm/plat-s3c24xx/s3c244x.h
  *
  * Copyright (c) 2004-2005 Simtec Electronics
  *	Ben Dooks <ben@simtec.co.uk>
diff --git a/arch/arm/plat-s3c24xx/sleep.S b/arch/arm/plat-s3c24xx/sleep.S
new file mode 100644
index 00000000000..435349dc324
--- /dev/null
+++ b/arch/arm/plat-s3c24xx/sleep.S
@@ -0,0 +1,157 @@
+/* linux/arch/arm/mach-s3c2410/sleep.S
+ *
+ * Copyright (c) 2004 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C2410 Power Manager (Suspend-To-RAM) support
+ *
+ * Based on PXA/SA1100 sleep code by:
+ *	Nicolas Pitre, (c) 2002 Monta Vista Software Inc
+ *	Cliff Brake, (c) 2001
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+*/
+
+#include <linux/linkage.h>
+#include <asm/assembler.h>
+#include <asm/hardware.h>
+#include <asm/arch/map.h>
+
+#include <asm/arch/regs-gpio.h>
+#include <asm/arch/regs-clock.h>
+#include <asm/arch/regs-mem.h>
+#include <asm/arch/regs-serial.h>
+
+/* CONFIG_DEBUG_RESUME is dangerous if your bootloader does not
+ * reset the UART configuration, only enable if you really need this!
+*/
+//#define CONFIG_DEBUG_RESUME
+
+	.text
+
+	/* s3c2410_cpu_save
+	 *
+	 * save enough of the CPU state to allow us to re-start
+	 * pm.c code. as we store items like the sp/lr, we will
+	 * end up returning from this function when the cpu resumes
+	 * so the return value is set to mark this.
+	 *
+	 * This arangement means we avoid having to flush the cache
+	 * from this code.
+	 *
+	 * entry:
+	 *	r0 = pointer to save block
+	 *
+	 * exit:
+	 *	r0 = 0 => we stored everything
+	 *	     1 => resumed from sleep
+	*/
+
+ENTRY(s3c2410_cpu_save)
+	stmfd	sp!, { r4 - r12, lr }
+
+	@@ store co-processor registers
+
+	mrc	p15, 0, r4, c13, c0, 0	@ PID
+	mrc	p15, 0, r5, c3, c0, 0	@ Domain ID
+	mrc	p15, 0, r6, c2, c0, 0	@ translation table base address
+	mrc	p15, 0, r7, c1, c0, 0	@ control register
+
+	stmia	r0, { r4 - r13 }
+
+	mov	r0, #0
+	ldmfd	sp, { r4 - r12, pc }
+
+	@@ return to the caller, after having the MMU
+	@@ turned on, this restores the last bits from the
+	@@ stack
+resume_with_mmu:
+	mov	r0, #1
+	ldmfd	sp!, { r4 - r12, pc }
+
+	.ltorg
+
+	@@ the next bits sit in the .data segment, even though they
+	@@ happen to be code... the s3c2410_sleep_save_phys needs to be
+	@@ accessed by the resume code before it can restore the MMU.
+	@@ This means that the variable has to be close enough for the
+	@@ code to read it... since the .text segment needs to be RO,
+	@@ the data segment can be the only place to put this code.
+
+	.data
+
+	.global	s3c2410_sleep_save_phys
+s3c2410_sleep_save_phys:
+	.word	0
+
+	/* s3c2410_cpu_resume
+	 *
+	 * resume code entry for bootloader to call
+	 *
+	 * we must put this code here in the data segment as we have no
+	 * other way of restoring the stack pointer after sleep, and we
+	 * must not write to the code segment (code is read-only)
+	*/
+
+ENTRY(s3c2410_cpu_resume)
+	mov	r0, #PSR_I_BIT | PSR_F_BIT | SVC_MODE
+	msr	cpsr_c, r0
+
+	@@ load UART to allow us to print the two characters for
+	@@ resume debug
+
+	mov	r2, #S3C24XX_PA_UART & 0xff000000
+	orr	r2, r2, #S3C24XX_PA_UART & 0xff000
+
+#if 0
+	/* SMDK2440 LED set */
+	mov	r14, #S3C24XX_PA_GPIO
+	ldr	r12, [ r14, #0x54 ]
+	bic	r12, r12, #3<<4
+	orr	r12, r12, #1<<7
+	str	r12, [ r14, #0x54 ]
+#endif
+
+#ifdef CONFIG_DEBUG_RESUME
+	mov	r3, #'L'
+	strb	r3, [ r2, #S3C2410_UTXH ]
+1001:
+	ldrb	r14, [ r3, #S3C2410_UTRSTAT ]
+	tst	r14, #S3C2410_UTRSTAT_TXE
+	beq	1001b
+#endif /* CONFIG_DEBUG_RESUME */
+
+	mov	r1, #0
+	mcr	p15, 0, r1, c8, c7, 0		@@ invalidate I & D TLBs
+	mcr	p15, 0, r1, c7, c7, 0		@@ invalidate I & D caches
+
+	ldr	r0, s3c2410_sleep_save_phys	@ address of restore block
+	ldmia	r0, { r4 - r13 }
+
+	mcr	p15, 0, r4, c13, c0, 0		@ PID
+	mcr	p15, 0, r5, c3, c0, 0		@ Domain ID
+	mcr	p15, 0, r6, c2, c0, 0		@ translation table base
+
+#ifdef CONFIG_DEBUG_RESUME
+	mov	r3, #'R'
+	strb	r3, [ r2, #S3C2410_UTXH ]
+#endif
+
+	ldr	r2, =resume_with_mmu
+	mcr	p15, 0, r7, c1, c0, 0		@ turn on MMU, etc
+	nop					@ second-to-last before mmu
+	mov	pc, r2				@ go back to virtual address
+
+	.ltorg
diff --git a/arch/arm/mach-s3c2410/time.c b/arch/arm/plat-s3c24xx/time.c
index 9910bf0f2ce..c523d1c9cce 100644
--- a/arch/arm/mach-s3c2410/time.c
+++ b/arch/arm/plat-s3c24xx/time.c
@@ -1,4 +1,4 @@
-/* linux/arch/arm/mach-s3c2410/time.c
+/* linux/arch/arm/plat-s3c24xx/time.c
  *
  * Copyright (C) 2003-2005 Simtec Electronics
  *	Ben Dooks, <ben@simtec.co.uk>
@@ -37,8 +37,8 @@
 #include <asm/arch/regs-irq.h>
 #include <asm/mach/time.h>
 
-#include "clock.h"
-#include "cpu.h"
+#include <asm/plat-s3c24xx/clock.h>
+#include <asm/plat-s3c24xx/cpu.h>
 
 static unsigned long timer_startval;
 static unsigned long timer_usec_ticks;
diff --git a/arch/avr32/mach-at32ap/clock.c b/arch/avr32/mach-at32ap/clock.c
index 3d0d1097389..ecbd4a21e43 100644
--- a/arch/avr32/mach-at32ap/clock.c
+++ b/arch/avr32/mach-at32ap/clock.c
@@ -3,7 +3,7 @@
  *
  * Copyright (C) 2006 Atmel Corporation
  *
- * Based on arch/arm/mach-at91rm9200/clock.c
+ * Based on arch/arm/mach-at91/clock.c
  *   Copyright (C) 2005 David Brownell
  *   Copyright (C) 2005 Ivan Kokshaysky
  *
diff --git a/arch/avr32/mach-at32ap/clock.h b/arch/avr32/mach-at32ap/clock.h
index f953f044ba4..bb8e1f29583 100644
--- a/arch/avr32/mach-at32ap/clock.h
+++ b/arch/avr32/mach-at32ap/clock.h
@@ -3,7 +3,7 @@
  *
  * Copyright (C) 2006 Atmel Corporation
  *
- * Based on arch/arm/mach-at91rm9200/clock.c
+ * Based on arch/arm/mach-at91/clock.c
  *   Copyright (C) 2005 David Brownell
  *   Copyright (C) 2005 Ivan Kokshaysky
  *