diff options
Diffstat (limited to 'arch/sh/boards/se/7751/setup.c')
| -rw-r--r-- | arch/sh/boards/se/7751/setup.c | 198 |
1 files changed, 0 insertions, 198 deletions
diff --git a/arch/sh/boards/se/7751/setup.c b/arch/sh/boards/se/7751/setup.c deleted file mode 100644 index 73e826310ba..00000000000 --- a/arch/sh/boards/se/7751/setup.c +++ /dev/null @@ -1,198 +0,0 @@ -/* - * linux/arch/sh/kernel/setup_7751se.c - * - * Copyright (C) 2000 Kazumoto Kojima - * - * Hitachi SolutionEngine Support. - * - * Modified for 7751 Solution Engine by - * Ian da Silva and Jeremy Siegel, 2001. - */ - -#include <linux/init.h> -#include <linux/irq.h> -#include <linux/ide.h> -#include <asm/io.h> -#include <asm/se7751.h> - -void heartbeat_7751se(void); -void init_7751se_IRQ(void); - -#ifdef CONFIG_SH_KGDB -#include <asm/kgdb.h> -static int kgdb_uart_setup(void); -static struct kgdb_sermap kgdb_uart_sermap = -{ "ttyS", 0, kgdb_uart_setup, NULL }; -#endif - -/* - * Initialize the board - */ -static void __init sh7751se_setup(char **cmdline_p) -{ - /* Call init_smsc() replacement to set up SuperIO. */ - /* XXX: RTC setting comes here */ -#ifdef CONFIG_SH_KGDB - kgdb_register_sermap(&kgdb_uart_sermap); -#endif -} - -/********************************************************************* - * Currently a hack (e.g. does not interact well w/serial.c, lots of * - * hardcoded stuff) but may be useful if SCI/F needs debugging. * - * Mostly copied from x86 code (see files asm-i386/kgdb_local.h and * - * arch/i386/lib/kgdb_serial.c). * - *********************************************************************/ - -#ifdef CONFIG_SH_KGDB -#include <linux/types.h> -#include <linux/serial.h> -#include <linux/serialP.h> -#include <linux/serial_reg.h> - -#define COM1_PORT 0x3f8 /* Base I/O address */ -#define COM1_IRQ 4 /* IRQ not used yet */ -#define COM2_PORT 0x2f8 /* Base I/O address */ -#define COM2_IRQ 3 /* IRQ not used yet */ - -#define SB_CLOCK 1843200 /* Serial baud clock */ -#define SB_BASE (SB_CLOCK/16) -#define SB_MCR UART_MCR_OUT2 | UART_MCR_DTR | UART_MCR_RTS - -struct uart_port { - int base; -}; -#define UART_NPORTS 2 -struct uart_port uart_ports[] = { - { COM1_PORT }, - { COM2_PORT }, -}; -struct uart_port *kgdb_uart_port; - -#define UART_IN(reg) inb_p(kgdb_uart_port->base + reg) -#define UART_OUT(reg,v) outb_p((v), kgdb_uart_port->base + reg) - -/* Basic read/write functions for the UART */ -#define UART_LSR_RXCERR (UART_LSR_BI | UART_LSR_FE | UART_LSR_PE) -static int kgdb_uart_getchar(void) -{ - int lsr; - int c = -1; - - while (c == -1) { - lsr = UART_IN(UART_LSR); - if (lsr & UART_LSR_DR) - c = UART_IN(UART_RX); - if ((lsr & UART_LSR_RXCERR)) - c = -1; - } - return c; -} - -static void kgdb_uart_putchar(int c) -{ - while ((UART_IN(UART_LSR) & UART_LSR_THRE) == 0) - ; - UART_OUT(UART_TX, c); -} - -/* - * Initialize UART to configured/requested values. - * (But we don't interrupts yet, or interact w/serial.c) - */ -static int kgdb_uart_setup(void) -{ - int port; - int lcr = 0; - int bdiv = 0; - - if (kgdb_portnum >= UART_NPORTS) { - KGDB_PRINTK("uart port %d invalid.\n", kgdb_portnum); - return -1; - } - - kgdb_uart_port = &uart_ports[kgdb_portnum]; - - /* Init sequence from gdb_hook_interrupt */ - UART_IN(UART_RX); - UART_OUT(UART_IER, 0); - - UART_IN(UART_RX); /* Serial driver comments say */ - UART_IN(UART_IIR); /* this clears interrupt regs */ - UART_IN(UART_MSR); - - /* Figure basic LCR values */ - switch (kgdb_bits) { - case '7': - lcr |= UART_LCR_WLEN7; - break; - default: case '8': - lcr |= UART_LCR_WLEN8; - break; - } - switch (kgdb_parity) { - case 'O': - lcr |= UART_LCR_PARITY; - break; - case 'E': - lcr |= (UART_LCR_PARITY | UART_LCR_EPAR); - break; - default: break; - } - - /* Figure the baud rate divisor */ - bdiv = (SB_BASE/kgdb_baud); - - /* Set the baud rate and LCR values */ - UART_OUT(UART_LCR, (lcr | UART_LCR_DLAB)); - UART_OUT(UART_DLL, (bdiv & 0xff)); - UART_OUT(UART_DLM, ((bdiv >> 8) & 0xff)); - UART_OUT(UART_LCR, lcr); - - /* Set the MCR */ - UART_OUT(UART_MCR, SB_MCR); - - /* Turn off FIFOs for now */ - UART_OUT(UART_FCR, 0); - - /* Setup complete: initialize function pointers */ - kgdb_getchar = kgdb_uart_getchar; - kgdb_putchar = kgdb_uart_putchar; - - return 0; -} -#endif /* CONFIG_SH_KGDB */ - - -/* - * The Machine Vector - */ - -struct sh_machine_vector mv_7751se __initmv = { - .mv_name = "7751 SolutionEngine", - .mv_setup = sh7751se_setup, - .mv_nr_irqs = 72, - - .mv_inb = sh7751se_inb, - .mv_inw = sh7751se_inw, - .mv_inl = sh7751se_inl, - .mv_outb = sh7751se_outb, - .mv_outw = sh7751se_outw, - .mv_outl = sh7751se_outl, - - .mv_inb_p = sh7751se_inb_p, - .mv_inw_p = sh7751se_inw, - .mv_inl_p = sh7751se_inl, - .mv_outb_p = sh7751se_outb_p, - .mv_outw_p = sh7751se_outw, - .mv_outl_p = sh7751se_outl, - - .mv_insl = sh7751se_insl, - .mv_outsl = sh7751se_outsl, - - .mv_init_irq = init_7751se_IRQ, -#ifdef CONFIG_HEARTBEAT - .mv_heartbeat = heartbeat_7751se, -#endif -}; -ALIAS_MV(7751se) |