diff options
Diffstat (limited to 'arch/powerpc/platforms/apus/Kconfig')
| -rw-r--r-- | arch/powerpc/platforms/apus/Kconfig | 130 |
1 files changed, 130 insertions, 0 deletions
diff --git a/arch/powerpc/platforms/apus/Kconfig b/arch/powerpc/platforms/apus/Kconfig new file mode 100644 index 00000000000..6bde3bffed8 --- /dev/null +++ b/arch/powerpc/platforms/apus/Kconfig @@ -0,0 +1,130 @@ + +config AMIGA + bool + depends on APUS + default y + help + This option enables support for the Amiga series of computers. + +config ZORRO + bool + depends on APUS + default y + help + This enables support for the Zorro bus in the Amiga. If you have + expansion cards in your Amiga that conform to the Amiga + AutoConfig(tm) specification, say Y, otherwise N. Note that even + expansion cards that do not fit in the Zorro slots but fit in e.g. + the CPU slot may fall in this category, so you have to say Y to let + Linux use these. + +config ABSTRACT_CONSOLE + bool + depends on APUS + default y + +config APUS_FAST_EXCEPT + bool + depends on APUS + default y + +config AMIGA_PCMCIA + bool "Amiga 1200/600 PCMCIA support" + depends on APUS && EXPERIMENTAL + help + Include support in the kernel for pcmcia on Amiga 1200 and Amiga + 600. If you intend to use pcmcia cards say Y; otherwise say N. + +config AMIGA_BUILTIN_SERIAL + tristate "Amiga builtin serial support" + depends on APUS + help + If you want to use your Amiga's built-in serial port in Linux, + answer Y. + + To compile this driver as a module, choose M here. + +config GVPIOEXT + tristate "GVP IO-Extender support" + depends on APUS + help + If you want to use a GVP IO-Extender serial card in Linux, say Y. + Otherwise, say N. + +config GVPIOEXT_LP + tristate "GVP IO-Extender parallel printer support" + depends on GVPIOEXT + help + Say Y to enable driving a printer from the parallel port on your + GVP IO-Extender card, N otherwise. + +config GVPIOEXT_PLIP + tristate "GVP IO-Extender PLIP support" + depends on GVPIOEXT + help + Say Y to enable doing IP over the parallel port on your GVP + IO-Extender card, N otherwise. + +config MULTIFACE_III_TTY + tristate "Multiface Card III serial support" + depends on APUS + help + If you want to use a Multiface III card's serial port in Linux, + answer Y. + + To compile this driver as a module, choose M here. + +config A2232 + tristate "Commodore A2232 serial support (EXPERIMENTAL)" + depends on EXPERIMENTAL && APUS + ---help--- + This option supports the 2232 7-port serial card shipped with the + Amiga 2000 and other Zorro-bus machines, dating from 1989. At + a max of 19,200 bps, the ports are served by a 6551 ACIA UART chip + each, plus a 8520 CIA, and a master 6502 CPU and buffer as well. The + ports were connected with 8 pin DIN connectors on the card bracket, + for which 8 pin to DB25 adapters were supplied. The card also had + jumpers internally to toggle various pinning configurations. + + This driver can be built as a module; but then "generic_serial" + will also be built as a module. This has to be loaded before + "ser_a2232". If you want to do this, answer M here. + +config WHIPPET_SERIAL + tristate "Hisoft Whippet PCMCIA serial support" + depends on AMIGA_PCMCIA + help + HiSoft has a web page at <http://www.hisoft.co.uk/>, but there + is no listing for the Whippet in their Amiga section. + +config APNE + tristate "PCMCIA NE2000 support" + depends on AMIGA_PCMCIA + help + If you have a PCMCIA NE2000 compatible adapter, say Y. Otherwise, + say N. + + To compile this driver as a module, choose M here: the + module will be called apne. + +config SERIAL_CONSOLE + bool "Support for serial port console" + depends on APUS && (AMIGA_BUILTIN_SERIAL=y || GVPIOEXT=y || MULTIFACE_III_TTY=y) + +config HEARTBEAT + bool "Use power LED as a heartbeat" + depends on APUS + help + Use the power-on LED on your machine as a load meter. The exact + behavior is platform-dependent, but normally the flash frequency is + a hyperbolic function of the 5-minute load average. + +config PROC_HARDWARE + bool "/proc/hardware support" + depends on APUS + +source "drivers/zorro/Kconfig" + +config PCI_PERMEDIA + bool "PCI for Permedia2" + depends on !4xx && !8xx && APUS |