diff options
Diffstat (limited to 'arch/mips/netlogic/xlr/platform.c')
| -rw-r--r-- | arch/mips/netlogic/xlr/platform.c | 140 |
1 files changed, 140 insertions, 0 deletions
diff --git a/arch/mips/netlogic/xlr/platform.c b/arch/mips/netlogic/xlr/platform.c index eab64b45dff..71b44d82621 100644 --- a/arch/mips/netlogic/xlr/platform.c +++ b/arch/mips/netlogic/xlr/platform.c @@ -14,6 +14,7 @@ #include <linux/resource.h> #include <linux/serial_8250.h> #include <linux/serial_reg.h> +#include <linux/i2c.h> #include <asm/netlogic/haldefs.h> #include <asm/netlogic/xlr/iomap.h> @@ -97,3 +98,142 @@ static int __init nlm_uart_init(void) } arch_initcall(nlm_uart_init); + +#ifdef CONFIG_USB +/* Platform USB devices, only on XLS chips */ +static u64 xls_usb_dmamask = ~(u32)0; +#define USB_PLATFORM_DEV(n, i, irq) \ + { \ + .name = n, \ + .id = i, \ + .num_resources = 2, \ + .dev = { \ + .dma_mask = &xls_usb_dmamask, \ + .coherent_dma_mask = 0xffffffff, \ + }, \ + .resource = (struct resource[]) { \ + { \ + .flags = IORESOURCE_MEM, \ + }, \ + { \ + .start = irq, \ + .end = irq, \ + .flags = IORESOURCE_IRQ, \ + }, \ + }, \ + } + +static struct platform_device xls_usb_ehci_device = + USB_PLATFORM_DEV("ehci-xls", 0, PIC_USB_IRQ); +static struct platform_device xls_usb_ohci_device_0 = + USB_PLATFORM_DEV("ohci-xls-0", 1, PIC_USB_IRQ); +static struct platform_device xls_usb_ohci_device_1 = + USB_PLATFORM_DEV("ohci-xls-1", 2, PIC_USB_IRQ); + +static struct platform_device *xls_platform_devices[] = { + &xls_usb_ehci_device, + &xls_usb_ohci_device_0, + &xls_usb_ohci_device_1, +}; + +int xls_platform_usb_init(void) +{ + uint64_t usb_mmio, gpio_mmio; + unsigned long memres; + uint32_t val; + + if (!nlm_chip_is_xls()) + return 0; + + gpio_mmio = nlm_mmio_base(NETLOGIC_IO_GPIO_OFFSET); + usb_mmio = nlm_mmio_base(NETLOGIC_IO_USB_1_OFFSET); + + /* Clear Rogue Phy INTs */ + nlm_write_reg(usb_mmio, 49, 0x10000000); + /* Enable all interrupts */ + nlm_write_reg(usb_mmio, 50, 0x1f000000); + + /* Enable ports */ + nlm_write_reg(usb_mmio, 1, 0x07000500); + + val = nlm_read_reg(gpio_mmio, 21); + if (((val >> 22) & 0x01) == 0) { + pr_info("Detected USB Device mode - Not supported!\n"); + nlm_write_reg(usb_mmio, 0, 0x01000000); + return 0; + } + + pr_info("Detected USB Host mode - Adding XLS USB devices.\n"); + /* Clear reset, host mode */ + nlm_write_reg(usb_mmio, 0, 0x02000000); + + /* Memory resource for various XLS usb ports */ + usb_mmio = nlm_mmio_base(NETLOGIC_IO_USB_0_OFFSET); + memres = CPHYSADDR((unsigned long)usb_mmio); + xls_usb_ehci_device.resource[0].start = memres; + xls_usb_ehci_device.resource[0].end = memres + 0x400 - 1; + + memres += 0x400; + xls_usb_ohci_device_0.resource[0].start = memres; + xls_usb_ohci_device_0.resource[0].end = memres + 0x400 - 1; + + memres += 0x400; + xls_usb_ohci_device_1.resource[0].start = memres; + xls_usb_ohci_device_1.resource[0].end = memres + 0x400 - 1; + + return platform_add_devices(xls_platform_devices, + ARRAY_SIZE(xls_platform_devices)); +} + +arch_initcall(xls_platform_usb_init); +#endif + +#ifdef CONFIG_I2C +static struct i2c_board_info nlm_i2c_board_info1[] __initdata = { + /* All XLR boards have this RTC and Max6657 Temp Chip */ + [0] = { + .type = "ds1374", + .addr = 0x68 + }, + [1] = { + .type = "lm90", + .addr = 0x4c + }, +}; + +static struct resource i2c_resources[] = { + [0] = { + .start = 0, /* filled at init */ + .end = 0, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device nlm_xlr_i2c_1 = { + .name = "xlr-i2cbus", + .id = 1, + .num_resources = 1, + .resource = i2c_resources, +}; + +static int __init nlm_i2c_init(void) +{ + int err = 0; + unsigned int offset; + + /* I2C bus 0 does not have any useful devices, configure only bus 1 */ + offset = NETLOGIC_IO_I2C_1_OFFSET; + nlm_xlr_i2c_1.resource[0].start = CPHYSADDR(nlm_mmio_base(offset)); + nlm_xlr_i2c_1.resource[0].end = nlm_xlr_i2c_1.resource[0].start + 0xfff; + + platform_device_register(&nlm_xlr_i2c_1); + + err = i2c_register_board_info(1, nlm_i2c_board_info1, + ARRAY_SIZE(nlm_i2c_board_info1)); + if (err < 0) + pr_err("nlm-i2c: cannot register board I2C devices\n"); + return err; +} + +arch_initcall(nlm_i2c_init); +#endif |