diff options
Diffstat (limited to 'arch/avr32/boards/atstk1000/atstk1002.c')
| -rw-r--r-- | arch/avr32/boards/atstk1000/atstk1002.c | 79 |
1 files changed, 31 insertions, 48 deletions
diff --git a/arch/avr32/boards/atstk1000/atstk1002.c b/arch/avr32/boards/atstk1000/atstk1002.c index 8538ba75ef9..6c80aba7bf9 100644 --- a/arch/avr32/boards/atstk1000/atstk1002.c +++ b/arch/avr32/boards/atstk1000/atstk1002.c @@ -16,17 +16,17 @@ #include <linux/types.h> #include <linux/spi/spi.h> #include <linux/spi/at73c213.h> +#include <linux/atmel-mci.h> #include <video/atmel_lcdc.h> #include <asm/io.h> #include <asm/setup.h> -#include <asm/atmel-mci.h> -#include <asm/arch/at32ap700x.h> -#include <asm/arch/board.h> -#include <asm/arch/init.h> -#include <asm/arch/portmux.h> +#include <mach/at32ap700x.h> +#include <mach/board.h> +#include <mach/init.h> +#include <mach/portmux.h> #include "atstk1000.h" @@ -49,7 +49,7 @@ unsigned long at32_board_osc_rates[3] = { */ #ifdef CONFIG_BOARD_ATSTK1006 #include <linux/mtd/partitions.h> -#include <asm/arch/smc.h> +#include <mach/smc.h> static struct smc_timing nand_timing __initdata = { .ncs_read_setup = 0, @@ -90,18 +90,14 @@ static struct mtd_partition nand_partitions[] = { }, }; -static struct mtd_partition *nand_part_info(int size, int *num_partitions) -{ - *num_partitions = ARRAY_SIZE(nand_partitions); - return nand_partitions; -} - -struct atmel_nand_data atstk1006_nand_data __initdata = { +static struct atmel_nand_data atstk1006_nand_data __initdata = { .cle = 21, .ale = 22, .rdy_pin = GPIO_PIN_PB(30), .enable_pin = GPIO_PIN_PB(29), - .partition_info = nand_part_info, + .ecc_mode = NAND_ECC_SOFT, + .parts = nand_partitions, + .num_parts = ARRAY_SIZE(nand_partitions), }; #endif @@ -110,7 +106,7 @@ struct eth_addr { }; static struct eth_addr __initdata hw_addr[2]; -static struct eth_platform_data __initdata eth_data[2] = { +static struct macb_platform_data __initdata eth_data[2] = { { /* * The MDIO pullups on STK1000 are a bit too weak for @@ -203,7 +199,7 @@ static void __init set_hw_addr(struct platform_device *pdev) */ regs = (void __iomem __force *)res->start; pclk = clk_get(&pdev->dev, "pclk"); - if (!pclk) + if (IS_ERR(pclk)) return; clk_enable(pclk); @@ -232,7 +228,7 @@ static void __init atstk1002_setup_extdac(void) goto err_set_clk; } - at32_select_periph(GPIO_PIN_PA(30), GPIO_PERIPH_A, 0); + at32_select_periph(GPIO_PIOA_BASE, (1 << 30), GPIO_PERIPH_A, 0); at73c213_data.dac_clk = gclk; err_set_clk: @@ -252,28 +248,32 @@ static void __init atstk1002_setup_extdac(void) void __init setup_board(void) { #ifdef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM - at32_map_usart(0, 1); /* USART 0/B: /dev/ttyS1, IRDA */ + at32_map_usart(0, 1, 0); /* USART 0/B: /dev/ttyS1, IRDA */ #else - at32_map_usart(1, 0); /* USART 1/A: /dev/ttyS0, DB9 */ + at32_map_usart(1, 0, 0); /* USART 1/A: /dev/ttyS0, DB9 */ #endif /* USART 2/unused: expansion connector */ - at32_map_usart(3, 2); /* USART 3/C: /dev/ttyS2, DB9 */ + at32_map_usart(3, 2, 0); /* USART 3/C: /dev/ttyS2, DB9 */ at32_setup_serial_console(0); } #ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM +static struct mci_platform_data __initdata mci0_data = { + .slot[0] = { + .bus_width = 4, + /* MMC card detect requires MACB0 *NOT* be used */ #ifdef CONFIG_BOARD_ATSTK1002_SW6_CUSTOM -static struct mci_platform_data __initdata mci0_data = { - .detect_pin = GPIO_PIN_PC(14), /* gpio30/sdcd */ - .wp_pin = GPIO_PIN_PC(15), /* gpio31/sdwp */ -}; -#define MCI_PDATA &mci0_data + .detect_pin = GPIO_PIN_PC(14), /* gpio30/sdcd */ + .wp_pin = GPIO_PIN_PC(15), /* gpio31/sdwp */ #else -#define MCI_PDATA NULL + .detect_pin = -ENODEV, + .wp_pin = -ENODEV, #endif /* SW6 for sd{cd,wp} routing */ + }, +}; #endif /* SW2 for MMC signal routing */ @@ -283,25 +283,7 @@ static int __init atstk1002_init(void) * ATSTK1000 uses 32-bit SDRAM interface. Reserve the * SDRAM-specific pins so that nobody messes with them. */ - at32_reserve_pin(GPIO_PIN_PE(0)); /* DATA[16] */ - at32_reserve_pin(GPIO_PIN_PE(1)); /* DATA[17] */ - at32_reserve_pin(GPIO_PIN_PE(2)); /* DATA[18] */ - at32_reserve_pin(GPIO_PIN_PE(3)); /* DATA[19] */ - at32_reserve_pin(GPIO_PIN_PE(4)); /* DATA[20] */ - at32_reserve_pin(GPIO_PIN_PE(5)); /* DATA[21] */ - at32_reserve_pin(GPIO_PIN_PE(6)); /* DATA[22] */ - at32_reserve_pin(GPIO_PIN_PE(7)); /* DATA[23] */ - at32_reserve_pin(GPIO_PIN_PE(8)); /* DATA[24] */ - at32_reserve_pin(GPIO_PIN_PE(9)); /* DATA[25] */ - at32_reserve_pin(GPIO_PIN_PE(10)); /* DATA[26] */ - at32_reserve_pin(GPIO_PIN_PE(11)); /* DATA[27] */ - at32_reserve_pin(GPIO_PIN_PE(12)); /* DATA[28] */ - at32_reserve_pin(GPIO_PIN_PE(13)); /* DATA[29] */ - at32_reserve_pin(GPIO_PIN_PE(14)); /* DATA[30] */ - at32_reserve_pin(GPIO_PIN_PE(15)); /* DATA[31] */ - at32_reserve_pin(GPIO_PIN_PE(26)); /* SDCS */ - - at32_add_system_devices(); + at32_reserve_pin(GPIO_PIOE_BASE, ATMEL_EBI_PE_DATA_ALL); #ifdef CONFIG_BOARD_ATSTK1006 smc_set_timing(&nand_config, &nand_timing); @@ -325,14 +307,15 @@ static int __init atstk1002_init(void) #ifdef CONFIG_BOARD_ATSTK100X_SPI1 at32_add_device_spi(1, spi1_board_info, ARRAY_SIZE(spi1_board_info)); #endif -#ifndef CONFIG_BOARD_ATSTK1002_SW2_CUSTOM - at32_add_device_mci(0, MCI_PDATA); +#ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM + at32_add_device_mci(0, &mci0_data); #endif #ifdef CONFIG_BOARD_ATSTK1002_SW5_CUSTOM set_hw_addr(at32_add_device_eth(1, ð_data[1])); #else at32_add_device_lcdc(0, &atstk1000_lcdc_data, - fbmem_start, fbmem_size, 0); + fbmem_start, fbmem_size, + ATMEL_LCDC_PRI_24BIT | ATMEL_LCDC_PRI_CONTROL); #endif at32_add_device_usba(0, NULL); #ifndef CONFIG_BOARD_ATSTK100X_SW3_CUSTOM |