19 files changed, 533 insertions, 10 deletions

diff --git a/arch/arm/plat-samsung/Kconfig b/arch/arm/plat-samsung/Kconfig
index 229919e9744..2753fb3e4f7 100644
--- a/arch/arm/plat-samsung/Kconfig
+++ b/arch/arm/plat-samsung/Kconfig
@@ -6,7 +6,7 @@
 
 config PLAT_SAMSUNG
 	bool
-	depends on ARCH_S3C2410 || ARCH_S3C24A0 || ARCH_S3C64XX || ARCH_S5PC1XX
+	depends on ARCH_S3C2410 || ARCH_S3C24A0 || ARCH_S3C64XX
 	select NO_IOPORT
 	default y
 	help
@@ -170,6 +170,11 @@ config S3C_DEV_I2C1
 	help
 	  Compile in platform device definitions for I2C channel 1
 
+config S3C_DEV_I2C2
+	bool
+	help
+	  Compile in platform device definitions for I2C channel 2
+
 config S3C_DEV_FB
 	bool
 	help
@@ -185,11 +190,22 @@ config S3C_DEV_USB_HSOTG
 	help
 	  Compile in platform device definition for USB high-speed OtG
 
+config S3C_DEV_WDT
+	bool
+	default y if ARCH_S3C2410
+	help
+	  Complie in platform device definition for Watchdog Timer
+
 config S3C_DEV_NAND
 	bool
 	help
 	  Compile in platform device definition for NAND controller
 
+config S3C_DEV_ONENAND
+	bool
+	help
+	  Compile in platform device definition for OneNAND controller
+
 config S3C_DEV_RTC
 	bool
 	help
@@ -269,4 +285,12 @@ config SAMSUNG_PM_CHECK_CHUNKSIZE
 
 	  See <file:Documentation/arm/Samsung-S3C24XX/Suspend.txt>
 
+config SAMSUNG_WAKEMASK
+	bool
+	depends on PM
+	help
+	  Compile support for wakeup-mask controls found on the S3C6400
+	  and above. This code allows a set of interrupt to wakeup-mask
+	  mappings. See <plat/wakeup-mask.h>
+
 endif
diff --git a/arch/arm/plat-samsung/Makefile b/arch/arm/plat-samsung/Makefile
index 48288499a3b..b1d82cc5e71 100644
--- a/arch/arm/plat-samsung/Makefile
+++ b/arch/arm/plat-samsung/Makefile
@@ -36,11 +36,14 @@ obj-$(CONFIG_S3C_DEV_HSMMC2)	+= dev-hsmmc2.o
 obj-$(CONFIG_S3C_DEV_HWMON)	+= dev-hwmon.o
 obj-y				+= dev-i2c0.o
 obj-$(CONFIG_S3C_DEV_I2C1)	+= dev-i2c1.o
+obj-$(CONFIG_S3C_DEV_I2C2)	+= dev-i2c2.o
 obj-$(CONFIG_S3C_DEV_FB)	+= dev-fb.o
 obj-y				+= dev-uart.o
 obj-$(CONFIG_S3C_DEV_USB_HOST)	+= dev-usb.o
 obj-$(CONFIG_S3C_DEV_USB_HSOTG)	+= dev-usb-hsotg.o
+obj-$(CONFIG_S3C_DEV_WDT)	+= dev-wdt.o
 obj-$(CONFIG_S3C_DEV_NAND)	+= dev-nand.o
+obj-$(CONFIG_S3C_DEV_ONENAND)	+= dev-onenand.o
 obj-$(CONFIG_S3C_DEV_RTC)	+= dev-rtc.o
 
 obj-$(CONFIG_SAMSUNG_DEV_ADC)	+= dev-adc.o
@@ -58,6 +61,8 @@ obj-$(CONFIG_PM)		+= pm.o
 obj-$(CONFIG_PM)		+= pm-gpio.o
 obj-$(CONFIG_SAMSUNG_PM_CHECK)	+= pm-check.o
 
+obj-$(CONFIG_SAMSUNG_WAKEMASK)	+= wakeup-mask.o
+
 # PWM support
 
 obj-$(CONFIG_HAVE_PWM)		+= pwm.o
diff --git a/arch/arm/plat-samsung/adc.c b/arch/arm/plat-samsung/adc.c
index 210030d5cfe..04d9521ddc9 100644
--- a/arch/arm/plat-samsung/adc.c
+++ b/arch/arm/plat-samsung/adc.c
@@ -66,6 +66,7 @@ struct adc_device {
 	struct s3c_adc_client	*cur;
 	struct s3c_adc_client	*ts_pend;
 	void __iomem		*regs;
+	spinlock_t		 lock;
 
 	unsigned int		 prescale;
 
@@ -74,7 +75,7 @@ struct adc_device {
 
 static struct adc_device *adc_dev;
 
-static LIST_HEAD(adc_pending);
+static LIST_HEAD(adc_pending);	/* protected by adc_device.lock */
 
 #define adc_dbg(_adc, msg...) dev_dbg(&(_adc)->pdev->dev, msg)
 
@@ -145,7 +146,7 @@ int s3c_adc_start(struct s3c_adc_client *client,
 	if (client->is_ts && adc->ts_pend)
 		return -EAGAIN;
 
-	local_irq_save(flags);
+	spin_lock_irqsave(&adc->lock, flags);
 
 	client->channel = channel;
 	client->nr_samples = nr_samples;
@@ -157,7 +158,8 @@ int s3c_adc_start(struct s3c_adc_client *client,
 
 	if (!adc->cur)
 		s3c_adc_try(adc);
-	local_irq_restore(flags);
+
+	spin_unlock_irqrestore(&adc->lock, flags);
 
 	return 0;
 }
@@ -237,6 +239,10 @@ EXPORT_SYMBOL_GPL(s3c_adc_register);
 
 void s3c_adc_release(struct s3c_adc_client *client)
 {
+	unsigned long flags;
+
+	spin_lock_irqsave(&adc_dev->lock, flags);
+
 	/* We should really check that nothing is in progress. */
 	if (adc_dev->cur == client)
 		adc_dev->cur = NULL;
@@ -255,6 +261,8 @@ void s3c_adc_release(struct s3c_adc_client *client)
 
 	if (adc_dev->cur == NULL)
 		s3c_adc_try(adc_dev);
+
+	spin_unlock_irqrestore(&adc_dev->lock, flags);
 	kfree(client);
 }
 EXPORT_SYMBOL_GPL(s3c_adc_release);
@@ -264,7 +272,6 @@ static irqreturn_t s3c_adc_irq(int irq, void *pw)
 	struct adc_device *adc = pw;
 	struct s3c_adc_client *client = adc->cur;
 	enum s3c_cpu_type cpu = platform_get_device_id(adc->pdev)->driver_data;
-	unsigned long flags;
 	unsigned data0, data1;
 
 	if (!client) {
@@ -296,12 +303,12 @@ static irqreturn_t s3c_adc_irq(int irq, void *pw)
 		client->select_cb(client, 1);
 		s3c_adc_convert(adc);
 	} else {
-		local_irq_save(flags);
+		spin_lock(&adc->lock);
 		(client->select_cb)(client, 0);
 		adc->cur = NULL;
 
 		s3c_adc_try(adc);
-		local_irq_restore(flags);
+		spin_unlock(&adc->lock);
 	}
 
 exit:
@@ -326,6 +333,8 @@ static int s3c_adc_probe(struct platform_device *pdev)
 		return -ENOMEM;
 	}
 
+	spin_lock_init(&adc->lock);
+
 	adc->pdev = pdev;
 	adc->prescale = S3C2410_ADCCON_PRSCVL(49);
 
@@ -407,13 +416,17 @@ static int __devexit s3c_adc_remove(struct platform_device *pdev)
 static int s3c_adc_suspend(struct platform_device *pdev, pm_message_t state)
 {
 	struct adc_device *adc = platform_get_drvdata(pdev);
+	unsigned long flags;
 	u32 con;
 
+	spin_lock_irqsave(&adc->lock, flags);
+
 	con = readl(adc->regs + S3C2410_ADCCON);
 	con |= S3C2410_ADCCON_STDBM;
 	writel(con, adc->regs + S3C2410_ADCCON);
 
 	disable_irq(adc->irq);
+	spin_unlock_irqrestore(&adc->lock, flags);
 	clk_disable(adc->clk);
 
 	return 0;
@@ -422,6 +435,7 @@ static int s3c_adc_suspend(struct platform_device *pdev, pm_message_t state)
 static int s3c_adc_resume(struct platform_device *pdev)
 {
 	struct adc_device *adc = platform_get_drvdata(pdev);
+	unsigned long flags;
 
 	clk_enable(adc->clk);
 	enable_irq(adc->irq);
diff --git a/arch/arm/plat-samsung/dev-i2c2.c b/arch/arm/plat-samsung/dev-i2c2.c
new file mode 100644
index 00000000000..07036dee09e
--- /dev/null
+++ b/arch/arm/plat-samsung/dev-i2c2.c
@@ -0,0 +1,70 @@
+/* linux/arch/arm/plat-s3c/dev-i2c2.c
+ *
+ * Copyright (c) 2010 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com/
+ *
+ * S3C series device definition for i2c device 2
+ *
+ * Based on plat-samsung/dev-i2c0.c
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/gfp.h>
+#include <linux/kernel.h>
+#include <linux/string.h>
+#include <linux/platform_device.h>
+
+#include <mach/irqs.h>
+#include <mach/map.h>
+
+#include <plat/regs-iic.h>
+#include <plat/iic.h>
+#include <plat/devs.h>
+#include <plat/cpu.h>
+
+static struct resource s3c_i2c_resource[] = {
+	[0] = {
+		.start = S3C_PA_IIC2,
+		.end   = S3C_PA_IIC2 + SZ_4K - 1,
+		.flags = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start = IRQ_CAN0,
+		.end   = IRQ_CAN0,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+struct platform_device s3c_device_i2c2 = {
+	.name		  = "s3c2410-i2c",
+	.id		  = 2,
+	.num_resources	  = ARRAY_SIZE(s3c_i2c_resource),
+	.resource	  = s3c_i2c_resource,
+};
+
+static struct s3c2410_platform_i2c default_i2c_data2 __initdata = {
+	.flags		= 0,
+	.bus_num	= 2,
+	.slave_addr	= 0x10,
+	.frequency	= 100*1000,
+	.sda_delay	= 100,
+};
+
+void __init s3c_i2c2_set_platdata(struct s3c2410_platform_i2c *pd)
+{
+	struct s3c2410_platform_i2c *npd;
+
+	if (!pd)
+		pd = &default_i2c_data2;
+
+	npd = kmemdup(pd, sizeof(struct s3c2410_platform_i2c), GFP_KERNEL);
+	if (!npd)
+		printk(KERN_ERR "%s: no memory for platform data\n", __func__);
+	else if (!npd->cfg_gpio)
+		npd->cfg_gpio = s3c_i2c2_cfg_gpio;
+
+	s3c_device_i2c2.dev.platform_data = npd;
+}
diff --git a/arch/arm/plat-samsung/dev-onenand.c b/arch/arm/plat-samsung/dev-onenand.c
new file mode 100644
index 00000000000..45ec73287d8
--- /dev/null
+++ b/arch/arm/plat-samsung/dev-onenand.c
@@ -0,0 +1,55 @@
+/*
+ * linux/arch/arm/plat-samsung/dev-onenand.c
+ *
+ *  Copyright (c) 2008-2010 Samsung Electronics
+ *  Kyungmin Park <kyungmin.park@samsung.com>
+ *
+ * S3C64XX/S5PC100 series device definition for OneNAND devices
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/onenand.h>
+
+#include <mach/irqs.h>
+#include <mach/map.h>
+
+static struct resource s3c_onenand_resources[] = {
+	[0] = {
+		.start	= S3C_PA_ONENAND,
+		.end	= S3C_PA_ONENAND + 0x400 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= S3C_PA_ONENAND_BUF,
+		.end	= S3C_PA_ONENAND_BUF + S3C_SZ_ONENAND_BUF - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[2] = {
+		.start	= IRQ_ONENAND,
+		.end	= IRQ_ONENAND,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+struct platform_device s3c_device_onenand = {
+	.name		= "samsung-onenand",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(s3c_onenand_resources),
+	.resource	= s3c_onenand_resources,
+};
+
+void s3c_onenand_set_platdata(struct onenand_platform_data *pdata)
+{
+	struct onenand_platform_data *pd;
+
+	pd = kmemdup(pdata, sizeof(struct onenand_platform_data), GFP_KERNEL);
+	if (!pd)
+		printk(KERN_ERR "%s: no memory for platform data\n", __func__);
+	s3c_device_onenand.dev.platform_data = pd;
+}
diff --git a/arch/arm/plat-samsung/dev-wdt.c b/arch/arm/plat-samsung/dev-wdt.c
new file mode 100644
index 00000000000..5efca87cddb
--- /dev/null
+++ b/arch/arm/plat-samsung/dev-wdt.c
@@ -0,0 +1,40 @@
+/* linux/arch/arm/plat-samsung/dev-wdt.c
+ *
+ * Copyright (c) 2004 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C series device definition for the watchdog timer
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+
+#include <mach/irqs.h>
+#include <mach/map.h>
+
+#include <plat/devs.h>
+
+static struct resource s3c_wdt_resource[] = {
+	[0] = {
+		.start	= S3C_PA_WDT,
+		.end	= S3C_PA_WDT + SZ_1M - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= IRQ_WDT,
+		.end	= IRQ_WDT,
+		.flags	= IORESOURCE_IRQ,
+	}
+};
+
+struct platform_device s3c_device_wdt = {
+	.name		= "s3c2410-wdt",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(s3c_wdt_resource),
+	.resource	= s3c_wdt_resource,
+};
+EXPORT_SYMBOL(s3c_device_wdt);
diff --git a/arch/arm/plat-samsung/include/plat/devs.h b/arch/arm/plat-samsung/include/plat/devs.h
index ef69e56b288..e6144e4b911 100644
--- a/arch/arm/plat-samsung/include/plat/devs.h
+++ b/arch/arm/plat-samsung/include/plat/devs.h
@@ -45,6 +45,7 @@ extern struct platform_device s3c_device_lcd;
 extern struct platform_device s3c_device_wdt;
 extern struct platform_device s3c_device_i2c0;
 extern struct platform_device s3c_device_i2c1;
+extern struct platform_device s3c_device_i2c2;
 extern struct platform_device s3c_device_rtc;
 extern struct platform_device s3c_device_adc;
 extern struct platform_device s3c_device_sdi;
@@ -57,9 +58,20 @@ extern struct platform_device s3c_device_hsmmc2;
 extern struct platform_device s3c_device_spi0;
 extern struct platform_device s3c_device_spi1;
 
+extern struct platform_device s5pc100_device_spi0;
+extern struct platform_device s5pc100_device_spi1;
+extern struct platform_device s5pc100_device_spi2;
+extern struct platform_device s5pv210_device_spi0;
+extern struct platform_device s5pv210_device_spi1;
+extern struct platform_device s5p6440_device_spi0;
+extern struct platform_device s5p6440_device_spi1;
+
 extern struct platform_device s3c_device_hwmon;
 
 extern struct platform_device s3c_device_nand;
+extern struct platform_device s3c_device_onenand;
+extern struct platform_device s3c64xx_device_onenand1;
+extern struct platform_device s5pc110_device_onenand;
 
 extern struct platform_device s3c_device_usbgadget;
 extern struct platform_device s3c_device_usb_hsotg;
@@ -76,10 +88,18 @@ extern struct platform_device s5p6442_device_pcm0;
 extern struct platform_device s5p6442_device_pcm1;
 extern struct platform_device s5p6442_device_iis0;
 extern struct platform_device s5p6442_device_iis1;
+extern struct platform_device s5p6442_device_spi;
 
 extern struct platform_device s5p6440_device_pcm;
 extern struct platform_device s5p6440_device_iis;
 
+extern struct platform_device s5pc100_device_ac97;
+extern struct platform_device s5pc100_device_pcm0;
+extern struct platform_device s5pc100_device_pcm1;
+extern struct platform_device s5pc100_device_iis0;
+extern struct platform_device s5pc100_device_iis1;
+extern struct platform_device s5pc100_device_iis2;
+
 /* s3c2440 specific devices */
 
 #ifdef CONFIG_CPU_S3C2440
diff --git a/arch/arm/plat-samsung/include/plat/fb.h b/arch/arm/plat-samsung/include/plat/fb.h
index 1f85649d8c1..27d3b497b55 100644
--- a/arch/arm/plat-samsung/include/plat/fb.h
+++ b/arch/arm/plat-samsung/include/plat/fb.h
@@ -84,4 +84,11 @@ extern void s3c64xx_fb_gpio_setup_24bpp(void);
  */
 extern void s5pc100_fb_gpio_setup_24bpp(void);
 
+/**
+ * s5pv210_fb_gpio_setup_24bpp() - S5PV210/S5PC110 setup function for 24bpp LCD
+ *
+ * Initialise the GPIO for an 24bpp LCD display on the RGB interface.
+ */
+extern void s5pv210_fb_gpio_setup_24bpp(void);
+
 #endif /* __PLAT_S3C_FB_H */
diff --git a/arch/arm/plat-samsung/include/plat/gpio-cfg.h b/arch/arm/plat-samsung/include/plat/gpio-cfg.h
index 34efdd2b032..db4112c6f2b 100644
--- a/arch/arm/plat-samsung/include/plat/gpio-cfg.h
+++ b/arch/arm/plat-samsung/include/plat/gpio-cfg.h
@@ -43,6 +43,11 @@ struct s3c_gpio_chip;
  * layouts. Provide an point to vector control routine and provide any
  * per-bank configuration information that other systems such as the
  * external interrupt code will need.
+ *
+ * @sa s3c_gpio_cfgpin
+ * @sa s3c_gpio_getcfg
+ * @sa s3c_gpio_setpull
+ * @sa s3c_gpio_getpull
  */
 struct s3c_gpio_cfg {
 	unsigned int	cfg_eint;
@@ -70,11 +75,25 @@ struct s3c_gpio_cfg {
 /**
  * s3c_gpio_cfgpin() - Change the GPIO function of a pin.
  * @pin pin The pin number to configure.
- * @pin to The configuration for the pin's function.
+ * @to to The configuration for the pin's function.
  *
  * Configure which function is actually connected to the external
  * pin, such as an gpio input, output or some form of special function
  * connected to an internal peripheral block.
+ *
+ * The @to parameter can be one of the generic S3C_GPIO_INPUT, S3C_GPIO_OUTPUT
+ * or S3C_GPIO_SFN() to indicate one of the possible values that the helper
+ * will then generate the correct bit mask and shift for the configuration.
+ *
+ * If a bank of GPIOs all needs to be set to special-function 2, then
+ * the following code will work:
+ *
+ *	for (gpio = start; gpio < end; gpio++)
+ *		s3c_gpio_cfgpin(gpio, S3C_GPIO_SFN(2));
+ *
+ * The @to parameter can also be a specific value already shifted to the
+ * correct position in the control register, although these are discouraged
+ * in newer kernels and are only being kept for compatibility.
  */
 extern int s3c_gpio_cfgpin(unsigned int pin, unsigned int to);
 
@@ -108,6 +127,8 @@ extern unsigned s3c_gpio_getcfg(unsigned int pin);
  * This function sets the state of the pull-{up,down} resistor for the
  * specified pin. It will return 0 if successfull, or a negative error
  * code if the pin cannot support the requested pull setting.
+ *
+ * @pull is one of S3C_GPIO_PULL_NONE, S3C_GPIO_PULL_DOWN or S3C_GPIO_PULL_UP.
 */
 extern int s3c_gpio_setpull(unsigned int pin, s3c_gpio_pull_t pull);
 
diff --git a/arch/arm/plat-samsung/include/plat/iic-core.h b/arch/arm/plat-samsung/include/plat/iic-core.h
index 36397ca2096..f182669b8e8 100644
--- a/arch/arm/plat-samsung/include/plat/iic-core.h
+++ b/arch/arm/plat-samsung/include/plat/iic-core.h
@@ -32,4 +32,11 @@ static inline void s3c_i2c1_setname(char *name)
 #endif
 }
 
+static inline void s3c_i2c2_setname(char *name)
+{
+#ifdef CONFIG_S3C_DEV_I2C2
+	s3c_device_i2c2.name = name;
+#endif
+}
+
 #endif /* __ASM_ARCH_IIC_H */
diff --git a/arch/arm/plat-samsung/include/plat/iic.h b/arch/arm/plat-samsung/include/plat/iic.h
index 3083df00dee..133308bf595 100644
--- a/arch/arm/plat-samsung/include/plat/iic.h
+++ b/arch/arm/plat-samsung/include/plat/iic.h
@@ -54,9 +54,11 @@ struct s3c2410_platform_i2c {
  */
 extern void s3c_i2c0_set_platdata(struct s3c2410_platform_i2c *i2c);
 extern void s3c_i2c1_set_platdata(struct s3c2410_platform_i2c *i2c);
+extern void s3c_i2c2_set_platdata(struct s3c2410_platform_i2c *i2c);
 
 /* defined by architecture to configure gpio */
 extern void s3c_i2c0_cfg_gpio(struct platform_device *dev);
 extern void s3c_i2c1_cfg_gpio(struct platform_device *dev);
+extern void s3c_i2c2_cfg_gpio(struct platform_device *dev);
 
 #endif /* __ASM_ARCH_IIC_H */
diff --git a/arch/arm/plat-samsung/include/plat/onenand-core.h b/arch/arm/plat-samsung/include/plat/onenand-core.h
new file mode 100644
index 00000000000..7701cb7020c
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/onenand-core.h
@@ -0,0 +1,37 @@
+/*
+ * linux/arch/arm/plat-samsung/onenand-core.h
+ *
+ *  Copyright (c) 2010 Samsung Electronics
+ *  Kyungmin Park <kyungmin.park@samsung.com>
+ *  Marek Szyprowski <m.szyprowski@samsung.com>
+ *
+ * Samsung OneNAD Controller core functions
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __ASM_ARCH_ONENAND_CORE_H
+#define __ASM_ARCH_ONENAND_CORE_H __FILE__
+
+/* These functions are only for use with the core support code, such as
+ * the cpu specific initialisation code
+ */
+
+/* re-define device name depending on support. */
+static inline void s3c_onenand_setname(char *name)
+{
+#ifdef CONFIG_S3C_DEV_ONENAND
+	s3c_device_onenand.name = name;
+#endif
+}
+
+static inline void s3c64xx_onenand1_setname(char *name)
+{
+#ifdef CONFIG_S3C64XX_DEV_ONENAND1
+	s3c64xx_device_onenand1.name = name;
+#endif
+}
+
+#endif /* __ASM_ARCH_ONENAND_CORE_H */
diff --git a/arch/arm/plat-samsung/include/plat/regs-onenand.h b/arch/arm/plat-samsung/include/plat/regs-onenand.h
new file mode 100644
index 00000000000..930ea8b88ed
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/regs-onenand.h
@@ -0,0 +1,63 @@
+/*
+ * linux/arch/arm/plat-s3c/include/plat/regs-onenand.h
+ *
+ *  Copyright (C) 2008-2010 Samsung Electronics
+ *  Kyungmin Park <kyungmin.park@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef __SAMSUNG_ONENAND_H__
+#define __SAMSUNG_ONENAND_H__
+
+#include <mach/hardware.h>
+
+/*
+ * OneNAND Controller
+ */
+#define MEM_CFG_OFFSET		0x0000
+#define BURST_LEN_OFFSET	0x0010
+#define MEM_RESET_OFFSET	0x0020
+#define INT_ERR_STAT_OFFSET	0x0030
+#define INT_ERR_MASK_OFFSET	0x0040
+#define INT_ERR_ACK_OFFSET	0x0050
+#define ECC_ERR_STAT_OFFSET	0x0060
+#define MANUFACT_ID_OFFSET	0x0070
+#define DEVICE_ID_OFFSET	0x0080
+#define DATA_BUF_SIZE_OFFSET	0x0090
+#define BOOT_BUF_SIZE_OFFSET	0x00A0
+#define BUF_AMOUNT_OFFSET	0x00B0
+#define TECH_OFFSET		0x00C0
+#define FBA_WIDTH_OFFSET	0x00D0
+#define FPA_WIDTH_OFFSET	0x00E0
+#define FSA_WIDTH_OFFSET	0x00F0
+#define TRANS_SPARE_OFFSET	0x0140
+#define DBS_DFS_WIDTH_OFFSET	0x0160
+#define INT_PIN_ENABLE_OFFSET	0x01A0
+#define ACC_CLOCK_OFFSET	0x01C0
+#define FLASH_VER_ID_OFFSET	0x01F0
+#define FLASH_AUX_CNTRL_OFFSET	0x0300		/* s3c64xx only */
+
+#define ONENAND_MEM_RESET_HOT	0x3
+#define ONENAND_MEM_RESET_COLD	0x2
+#define ONENAND_MEM_RESET_WARM	0x1
+
+#define CACHE_OP_ERR		(1 << 13)
+#define RST_CMP			(1 << 12)
+#define RDY_ACT			(1 << 11)
+#define INT_ACT			(1 << 10)
+#define UNSUP_CMD		(1 << 9)
+#define LOCKED_BLK		(1 << 8)
+#define BLK_RW_CMP		(1 << 7)
+#define ERS_CMP			(1 << 6)
+#define PGM_CMP			(1 << 5)
+#define LOAD_CMP		(1 << 4)
+#define ERS_FAIL		(1 << 3)
+#define PGM_FAIL		(1 << 2)
+#define INT_TO			(1 << 1)
+#define LD_FAIL_ECC_ERR		(1 << 0)
+
+#define TSRF			(1 << 0)
+
+#endif
diff --git a/arch/arm/plat-samsung/include/plat/regs-rtc.h b/arch/arm/plat-samsung/include/plat/regs-rtc.h
index d5837cf8e40..65c190d142d 100644
--- a/arch/arm/plat-samsung/include/plat/regs-rtc.h
+++ b/arch/arm/plat-samsung/include/plat/regs-rtc.h
@@ -20,6 +20,10 @@
 #define S3C2410_RTCCON_CLKSEL (1<<1)
 #define S3C2410_RTCCON_CNTSEL (1<<2)
 #define S3C2410_RTCCON_CLKRST (1<<3)
+#define S3C64XX_RTCCON_TICEN  (1<<8)
+
+#define S3C64XX_RTCCON_TICMSK (0xF<<7)
+#define S3C64XX_RTCCON_TICSHT (7)
 
 #define S3C2410_TICNT	      S3C2410_RTCREG(0x44)
 #define S3C2410_TICNT_ENABLE  (1<<7)
diff --git a/arch/arm/plat-samsung/include/plat/s3c64xx-spi.h b/arch/arm/plat-samsung/include/plat/s3c64xx-spi.h
index d1772414931..e5aba8f95b7 100644
--- a/arch/arm/plat-samsung/include/plat/s3c64xx-spi.h
+++ b/arch/arm/plat-samsung/include/plat/s3c64xx-spi.h
@@ -63,5 +63,9 @@ struct s3c64xx_spi_info {
  * has some chips attached to it.
  */
 extern void s3c64xx_spi_set_info(int cntrlr, int src_clk_nr, int num_cs);
+extern void s5pc100_spi_set_info(int cntrlr, int src_clk_nr, int num_cs);
+extern void s5pv210_spi_set_info(int cntrlr, int src_clk_nr, int num_cs);
+extern void s5p6440_spi_set_info(int cntrlr, int src_clk_nr, int num_cs);
+extern void s5p6442_spi_set_info(int cntrlr, int src_clk_nr, int num_cs);
 
 #endif /* __S3C64XX_PLAT_SPI_H */
diff --git a/arch/arm/plat-samsung/include/plat/sdhci.h b/arch/arm/plat-samsung/include/plat/sdhci.h
index 7d07cd7aa4f..13f9fb20900 100644
--- a/arch/arm/plat-samsung/include/plat/sdhci.h
+++ b/arch/arm/plat-samsung/include/plat/sdhci.h
@@ -75,6 +75,9 @@ extern void s5pc100_setup_sdhci0_cfg_gpio(struct platform_device *, int w);
 extern void s5pc100_setup_sdhci1_cfg_gpio(struct platform_device *, int w);
 extern void s5pc100_setup_sdhci2_cfg_gpio(struct platform_device *, int w);
 extern void s3c64xx_setup_sdhci2_cfg_gpio(struct platform_device *, int w);
+extern void s5pv210_setup_sdhci0_cfg_gpio(struct platform_device *, int w);
+extern void s5pv210_setup_sdhci1_cfg_gpio(struct platform_device *, int w);
+extern void s5pv210_setup_sdhci2_cfg_gpio(struct platform_device *, int w);
 
 /* S3C6400 SDHCI setup */
 
@@ -218,4 +221,56 @@ static inline void s5pc100_default_sdhci1(void) { }
 static inline void s5pc100_default_sdhci2(void) { }
 #endif /* CONFIG_S5PC100_SETUP_SDHCI */
 
+
+/* S5PC110 SDHCI setup */
+#ifdef CONFIG_S5PV210_SETUP_SDHCI
+extern char *s5pv210_hsmmc_clksrcs[4];
+
+extern void s5pv210_setup_sdhci_cfg_card(struct platform_device *dev,
+					   void __iomem *r,
+					   struct mmc_ios *ios,
+					   struct mmc_card *card);
+
+#ifdef CONFIG_S3C_DEV_HSMMC
+static inline void s5pv210_default_sdhci0(void)
+{
+	s3c_hsmmc0_def_platdata.clocks = s5pv210_hsmmc_clksrcs;
+	s3c_hsmmc0_def_platdata.cfg_gpio = s5pv210_setup_sdhci0_cfg_gpio;
+	s3c_hsmmc0_def_platdata.cfg_card = s5pv210_setup_sdhci_cfg_card;
+}
+#else
+static inline void s5pc100_default_sdhci0(void) { }
+#endif /* CONFIG_S3C_DEV_HSMMC */
+
+#ifdef CONFIG_S3C_DEV_HSMMC1
+static inline void s5pv210_default_sdhci1(void)
+{
+	s3c_hsmmc1_def_platdata.clocks = s5pv210_hsmmc_clksrcs;
+	s3c_hsmmc1_def_platdata.cfg_gpio = s5pv210_setup_sdhci1_cfg_gpio;
+	s3c_hsmmc1_def_platdata.cfg_card = s5pv210_setup_sdhci_cfg_card;
+}
+#else
+static inline void s5pv210_default_sdhci1(void) { }
+#endif /* CONFIG_S3C_DEV_HSMMC1 */
+
+#ifdef CONFIG_S3C_DEV_HSMMC2
+static inline void s5pv210_default_sdhci2(void)
+{
+	s3c_hsmmc2_def_platdata.clocks = s5pv210_hsmmc_clksrcs;
+	s3c_hsmmc2_def_platdata.cfg_gpio = s5pv210_setup_sdhci2_cfg_gpio;
+	s3c_hsmmc2_def_platdata.cfg_card = s5pv210_setup_sdhci_cfg_card;
+}
+#else
+static inline void s5pv210_default_sdhci2(void) { }
+#endif /* CONFIG_S3C_DEV_HSMMC2 */
+
+#else
+static inline void s5pv210_default_sdhci0(void) { }
+static inline void s5pv210_default_sdhci1(void) { }
+static inline void s5pv210_default_sdhci2(void) { }
+#endif /* CONFIG_S5PC100_SETUP_SDHCI */
+
+
+
+
 #endif /* __PLAT_S3C_SDHCI_H */
diff --git a/arch/arm/plat-samsung/include/plat/wakeup-mask.h b/arch/arm/plat-samsung/include/plat/wakeup-mask.h
new file mode 100644
index 00000000000..43e4acd2e1c
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/wakeup-mask.h
@@ -0,0 +1,44 @@
+/* arch/arm/plat-samsung/include/plat/wakeup-mask.h
+ *
+ * Copyright 2010 Ben Dooks <ben-linux@fluff.org>
+ *
+ * Support for wakeup mask interrupts on newer SoCs
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+*/
+
+#ifndef __PLAT_WAKEUP_MASK_H
+#define __PLAT_WAKEUP_MASK_H __file__
+
+/* if no irq yet defined, but still want to mask */
+#define NO_WAKEUP_IRQ (0x90000000)
+
+/**
+ * struct samsung_wakeup_mask - wakeup mask information
+ * @irq: The interrupt associated with this wakeup.
+ * @bit: The bit, as a (1 << bitno) controlling this source.
+ */ 
+struct samsung_wakeup_mask {
+	unsigned int	irq;
+	u32		bit;
+};
+
+/**
+ * samsung_sync_wakemask - sync wakeup mask information for pm
+ * @reg: The register that is used.
+ * @masks: The list of masks to use.
+ * @nr_masks: The number of entries pointed to buy @masks.
+ *
+ * Synchronise the wakeup mask information at suspend time from the list
+ * of interrupts and control bits in @masks. We do this at suspend time
+ * as overriding the relevant irq chips is harder and the register is only
+ * required to be correct before we enter sleep.
+ */
+extern void samsung_sync_wakemask(void __iomem *reg,
+				  struct samsung_wakeup_mask *masks,
+				  int nr_masks);
+
+#endif /* __PLAT_WAKEUP_MASK_H */
diff --git a/arch/arm/plat-samsung/pm-gpio.c b/arch/arm/plat-samsung/pm-gpio.c
index d50ab9d2af5..7df03f87fbf 100644
--- a/arch/arm/plat-samsung/pm-gpio.c
+++ b/arch/arm/plat-samsung/pm-gpio.c
@@ -331,8 +331,10 @@ void s3c_pm_save_gpios(void)
 
 	for (gpio_nr = 0; gpio_nr < S3C_GPIO_END;) {
 		ourchip = s3c_gpiolib_getchip(gpio_nr);
-		if (!ourchip)
+		if (!ourchip) {
+			gpio_nr++;
 			continue;
+		}
 
 		s3c_pm_save_gpio(ourchip);
 
@@ -369,8 +371,10 @@ void s3c_pm_restore_gpios(void)
 
 	for (gpio_nr = 0; gpio_nr < S3C_GPIO_END;) {
 		ourchip = s3c_gpiolib_getchip(gpio_nr);
-		if (!ourchip)
+		if (!ourchip) {
+			gpio_nr++;
 			continue;
+		}
 
 		s3c_pm_resume_gpio(ourchip);
 
diff --git a/arch/arm/plat-samsung/wakeup-mask.c b/arch/arm/plat-samsung/wakeup-mask.c
new file mode 100644
index 00000000000..2e09b6ad84c
--- /dev/null
+++ b/arch/arm/plat-samsung/wakeup-mask.c
@@ -0,0 +1,47 @@
+/* arch/arm/plat-samsung/wakeup-mask.c
+ *
+ * Copyright 2010 Ben Dooks <ben-linux@fluff.org>
+ *
+ * Support for wakeup mask interrupts on newer SoCs
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/spinlock.h>
+#include <linux/sysdev.h>
+#include <linux/types.h>
+#include <linux/irq.h>
+#include <linux/io.h>
+
+#include <plat/wakeup-mask.h>
+#include <plat/pm.h>
+
+void samsung_sync_wakemask(void __iomem *reg,
+			   struct samsung_wakeup_mask *mask, int nr_mask)
+{
+	struct irq_desc *desc;
+	u32 val;
+
+	val = __raw_readl(reg);
+
+	for (; nr_mask > 0; nr_mask--, mask++) {
+		if (mask->irq == NO_WAKEUP_IRQ) {
+			val |= mask->bit;
+			continue;
+		}
+
+		desc = irq_to_desc(mask->irq);
+
+		/* bit of a liberty to read this directly from irq_desc. */
+		if (desc->wake_depth > 0)
+			val &= ~mask->bit;
+		else
+			val |= mask->bit;
+	}
+
+	printk(KERN_INFO "wakemask %08x => %08x\n", __raw_readl(reg), val);
+	__raw_writel(val, reg);
+}