aboutsummaryrefslogtreecommitdiff
path: root/arch/arm/plat-s3c/Kconfig
diff options
context:
space:
mode:
Diffstat (limited to 'arch/arm/plat-s3c/Kconfig')
-rw-r--r--arch/arm/plat-s3c/Kconfig215
1 files changed, 0 insertions, 215 deletions
diff --git a/arch/arm/plat-s3c/Kconfig b/arch/arm/plat-s3c/Kconfig
deleted file mode 100644
index 9e9d0286e48..00000000000
--- a/arch/arm/plat-s3c/Kconfig
+++ /dev/null
@@ -1,215 +0,0 @@
-# Copyright 2007 Simtec Electronics
-#
-# Licensed under GPLv2
-
-config PLAT_S3C
- bool
- depends on ARCH_S3C2410 || ARCH_S3C24A0 || ARCH_S3C64XX
- default y
- select NO_IOPORT
- help
- Base platform code for any Samsung S3C device
-
-# low-level serial option nodes
-
-if PLAT_S3C
-
-config CPU_LLSERIAL_S3C2410_ONLY
- bool
- default y if CPU_LLSERIAL_S3C2410 && !CPU_LLSERIAL_S3C2440
-
-config CPU_LLSERIAL_S3C2440_ONLY
- bool
- default y if CPU_LLSERIAL_S3C2440 && !CPU_LLSERIAL_S3C2410
-
-config CPU_LLSERIAL_S3C2410
- bool
- help
- Selected if there is an S3C2410 (or register compatible) serial
- low-level implementation needed
-
-config CPU_LLSERIAL_S3C2440
- bool
- help
- Selected if there is an S3C2440 (or register compatible) serial
- low-level implementation needed
-
-# boot configurations
-
-comment "Boot options"
-
-config S3C_BOOT_WATCHDOG
- bool "S3C Initialisation watchdog"
- depends on S3C2410_WATCHDOG
- help
- Say y to enable the watchdog during the kernel decompression
- stage. If the kernel fails to uncompress, then the watchdog
- will trigger a reset and the system should restart.
-
-config S3C_BOOT_ERROR_RESET
- bool "S3C Reboot on decompression error"
- help
- Say y here to use the watchdog to reset the system if the
- kernel decompressor detects an error during decompression.
-
-config S3C_BOOT_UART_FORCE_FIFO
- bool "Force UART FIFO on during boot process"
- default y
- help
- Say Y here to force the UART FIFOs on during the kernel
- uncompressor
-
-comment "Power management"
-
-config S3C2410_PM_DEBUG
- bool "S3C2410 PM Suspend debug"
- depends on PM
- help
- Say Y here if you want verbose debugging from the PM Suspend and
- Resume code. See <file:Documentation/arm/Samsung-S3C24XX/Suspend.txt>
- for more information.
-
-config S3C_PM_DEBUG_LED_SMDK
- bool "SMDK LED suspend/resume debugging"
- depends on PM && (MACH_SMDK6410)
- help
- Say Y here to enable the use of the SMDK LEDs on the baseboard
- for debugging of the state of the suspend and resume process.
-
- Note, this currently only works for S3C64XX based SMDK boards.
-
-config S3C2410_PM_CHECK
- bool "S3C2410 PM Suspend Memory CRC"
- depends on PM && CRC32
- help
- Enable the PM code's memory area checksum over sleep. This option
- will generate CRCs of all blocks of memory, and store them before
- going to sleep. The blocks are then checked on resume for any
- errors.
-
- Note, this can take several seconds depending on memory size
- and CPU speed.
-
- See <file:Documentation/arm/Samsung-S3C24XX/Suspend.txt>
-
-config S3C2410_PM_CHECK_CHUNKSIZE
- int "S3C2410 PM Suspend CRC Chunksize (KiB)"
- depends on PM && S3C2410_PM_CHECK
- default 64
- help
- Set the chunksize in Kilobytes of the CRC for checking memory
- corruption over suspend and resume. A smaller value will mean that
- the CRC data block will take more memory, but wil identify any
- faults with better precision.
-
- See <file:Documentation/arm/Samsung-S3C24XX/Suspend.txt>
-
-config S3C_LOWLEVEL_UART_PORT
- int "S3C UART to use for low-level messages"
- default 0
- help
- Choice of which UART port to use for the low-level messages,
- such as the `Uncompressing...` at start time. The value of
- this configuration should be between zero and two. The port
- must have been initialised by the boot-loader before use.
-
-# options for gpiolib support
-
-config S3C_GPIO_SPACE
- int "Space between gpio banks"
- default 0
- help
- Add a number of spare GPIO entries between each bank for debugging
- purposes. This allows any problems where an counter overflows from
- one bank to another to be caught, at the expense of using a little
- more memory.
-
-config S3C_GPIO_TRACK
- bool
- help
- Internal configuration option to enable the s3c specific gpio
- chip tracking if the platform requires it.
-
-config S3C_GPIO_PULL_UPDOWN
- bool
- help
- Internal configuration to enable the correct GPIO pull helper
-
-config S3C_GPIO_PULL_DOWN
- bool
- help
- Internal configuration to enable the correct GPIO pull helper
-
-config S3C_GPIO_PULL_UP
- bool
- help
- Internal configuration to enable the correct GPIO pull helper
-
-config S3C_GPIO_CFG_S3C24XX
- bool
- help
- Internal configuration to enable S3C24XX style GPIO configuration
- functions.
-
-config S3C_GPIO_CFG_S3C64XX
- bool
- help
- Internal configuration to enable S3C64XX style GPIO configuration
- functions.
-
-config S5P_GPIO_CFG_S5PC1XX
- bool
- help
- Internal configuration to enable S5PC1XX style GPIO configuration
- functions.
-
-# DMA
-
-config S3C_DMA
- bool
- help
- Internal configuration for S3C DMA core
-
-# device definitions to compile in
-
-config S3C_DEV_HSMMC
- bool
- help
- Compile in platform device definitions for HSMMC code
-
-config S3C_DEV_HSMMC1
- bool
- help
- Compile in platform device definitions for HSMMC channel 1
-
-config S3C_DEV_HSMMC2
- bool
- help
- Compile in platform device definitions for HSMMC channel 2
-
-config S3C_DEV_I2C1
- bool
- help
- Compile in platform device definitions for I2C channel 1
-
-config S3C_DEV_FB
- bool
- help
- Compile in platform device definition for framebuffer
-
-config S3C_DEV_USB_HOST
- bool
- help
- Compile in platform device definition for USB host.
-
-config S3C_DEV_USB_HSOTG
- bool
- help
- Compile in platform device definition for USB high-speed OtG
-
-config S3C_DEV_NAND
- bool
- help
- Compile in platform device definition for NAND controller
-
-endif