diff options
Diffstat (limited to 'arch/arm/mach-orion5x/ts409-setup.c')
| -rw-r--r-- | arch/arm/mach-orion5x/ts409-setup.c | 122 |
1 files changed, 86 insertions, 36 deletions
diff --git a/arch/arm/mach-orion5x/ts409-setup.c b/arch/arm/mach-orion5x/ts409-setup.c index 32f0ff073b7..5c079d31201 100644 --- a/arch/arm/mach-orion5x/ts409-setup.c +++ b/arch/arm/mach-orion5x/ts409-setup.c @@ -3,12 +3,15 @@ * * Maintainer: Sylver Bruneau <sylver.bruneau@gmail.com> * + * Copyright (C) 2008 Sylver Bruneau <sylver.bruneau@gmail.com> + * Copyright (C) 2008 Martin Michlmayr <tbm@cyrius.com> + * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License * as published by the Free Software Foundation; either version * 2 of the License, or (at your option) any later version. */ - +#include <linux/gpio.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> @@ -16,15 +19,15 @@ #include <linux/irq.h> #include <linux/mtd/physmap.h> #include <linux/mv643xx_eth.h> +#include <linux/leds.h> #include <linux/gpio_keys.h> #include <linux/input.h> #include <linux/i2c.h> #include <linux/serial_reg.h> #include <asm/mach-types.h> -#include <asm/gpio.h> #include <asm/mach/arch.h> #include <asm/mach/pci.h> -#include <asm/arch/orion5x.h> +#include <mach/orion5x.h> #include "common.h" #include "mpp.h" #include "tsx09-common.h" @@ -52,7 +55,7 @@ /**************************************************************************** * 8MiB NOR flash. The struct mtd_partition is not in the same order as the - * partitions on the device because we want to keep compatability with + * partitions on the device because we want to keep compatibility with * existing QNAP firmware. * * Layout as used by QNAP: @@ -117,7 +120,8 @@ static struct platform_device qnap_ts409_nor_flash = { * PCI ****************************************************************************/ -static int __init qnap_ts409_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin) +static int __init qnap_ts409_pci_map_irq(const struct pci_dev *dev, u8 slot, + u8 pin) { int irq; @@ -136,7 +140,6 @@ static int __init qnap_ts409_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin) static struct hw_pci qnap_ts409_pci __initdata = { .nr_controllers = 2, - .swizzle = pci_std_swizzle, .setup = orion5x_pci_sys_setup, .scan = orion5x_pci_sys_scan_bus, .map_irq = qnap_ts409_pci_map_irq, @@ -162,16 +165,59 @@ static struct i2c_board_info __initdata qnap_ts409_i2c_rtc = { I2C_BOARD_INFO("s35390a", 0x30), }; +/***************************************************************************** + * LEDs attached to GPIO + ****************************************************************************/ + +static struct gpio_led ts409_led_pins[] = { + { + .name = "ts409:red:sata1", + .gpio = 4, + .active_low = 1, + }, { + .name = "ts409:red:sata2", + .gpio = 5, + .active_low = 1, + }, { + .name = "ts409:red:sata3", + .gpio = 6, + .active_low = 1, + }, { + .name = "ts409:red:sata4", + .gpio = 7, + .active_low = 1, + }, +}; + +static struct gpio_led_platform_data ts409_led_data = { + .leds = ts409_led_pins, + .num_leds = ARRAY_SIZE(ts409_led_pins), +}; + +static struct platform_device ts409_leds = { + .name = "leds-gpio", + .id = -1, + .dev = { + .platform_data = &ts409_led_data, + }, +}; + /**************************************************************************** * GPIO Attached Keys * Power button is attached to the PIC microcontroller ****************************************************************************/ +#define QNAP_TS409_GPIO_KEY_RESET 14 #define QNAP_TS409_GPIO_KEY_MEDIA 15 static struct gpio_keys_button qnap_ts409_buttons[] = { { .code = KEY_RESTART, + .gpio = QNAP_TS409_GPIO_KEY_RESET, + .desc = "Reset Button", + .active_low = 1, + }, { + .code = KEY_COPY, .gpio = QNAP_TS409_GPIO_KEY_MEDIA, .desc = "USB Copy Button", .active_low = 1, @@ -195,28 +241,28 @@ static struct platform_device qnap_ts409_button_device = { /***************************************************************************** * General Setup ****************************************************************************/ -static struct orion5x_mpp_mode ts409_mpp_modes[] __initdata = { - { 0, MPP_UNUSED }, - { 1, MPP_UNUSED }, - { 2, MPP_UNUSED }, - { 3, MPP_UNUSED }, - { 4, MPP_GPIO }, /* HDD 1 status */ - { 5, MPP_GPIO }, /* HDD 2 status */ - { 6, MPP_GPIO }, /* HDD 3 status */ - { 7, MPP_GPIO }, /* HDD 4 status */ - { 8, MPP_UNUSED }, - { 9, MPP_UNUSED }, - { 10, MPP_GPIO }, /* RTC int */ - { 11, MPP_UNUSED }, - { 12, MPP_UNUSED }, - { 13, MPP_UNUSED }, - { 14, MPP_GPIO }, /* SW_RST */ - { 15, MPP_GPIO }, /* USB copy button */ - { 16, MPP_UART }, /* UART1 RXD */ - { 17, MPP_UART }, /* UART1 TXD */ - { 18, MPP_UNUSED }, - { 19, MPP_UNUSED }, - { -1 }, +static unsigned int ts409_mpp_modes[] __initdata = { + MPP0_UNUSED, + MPP1_UNUSED, + MPP2_UNUSED, + MPP3_UNUSED, + MPP4_GPIO, /* HDD 1 status */ + MPP5_GPIO, /* HDD 2 status */ + MPP6_GPIO, /* HDD 3 status */ + MPP7_GPIO, /* HDD 4 status */ + MPP8_UNUSED, + MPP9_UNUSED, + MPP10_GPIO, /* RTC int */ + MPP11_UNUSED, + MPP12_UNUSED, + MPP13_UNUSED, + MPP14_GPIO, /* SW_RST */ + MPP15_GPIO, /* USB copy button */ + MPP16_UART, /* UART1 RXD */ + MPP17_UART, /* UART1 TXD */ + MPP18_UNUSED, + MPP19_UNUSED, + 0, }; static void __init qnap_ts409_init(void) @@ -231,6 +277,12 @@ static void __init qnap_ts409_init(void) /* * Configure peripherals. */ + mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET, + ORION_MBUS_DEVBUS_BOOT_ATTR, + QNAP_TS409_NOR_BOOT_BASE, + QNAP_TS409_NOR_BOOT_SIZE); + platform_device_register(&qnap_ts409_nor_flash); + orion5x_ehci0_init(); qnap_tsx09_find_mac_addr(QNAP_TS409_NOR_BOOT_BASE + qnap_ts409_partitions[5].offset, @@ -238,10 +290,7 @@ static void __init qnap_ts409_init(void) orion5x_eth_init(&qnap_tsx09_eth_data); orion5x_i2c_init(); orion5x_uart0_init(); - - orion5x_setup_dev_boot_win(QNAP_TS409_NOR_BOOT_BASE, - QNAP_TS409_NOR_BOOT_SIZE); - platform_device_register(&qnap_ts409_nor_flash); + orion5x_uart1_init(); platform_device_register(&qnap_ts409_button_device); @@ -255,6 +304,7 @@ static void __init qnap_ts409_init(void) if (qnap_ts409_i2c_rtc.irq == 0) pr_warning("qnap_ts409_init: failed to get RTC IRQ\n"); i2c_register_board_info(0, &qnap_ts409_i2c_rtc, 1); + platform_device_register(&ts409_leds); /* register tsx09 specific power-off method */ pm_power_off = qnap_tsx09_power_off; @@ -262,12 +312,12 @@ static void __init qnap_ts409_init(void) MACHINE_START(TS409, "QNAP TS-409") /* Maintainer: Sylver Bruneau <sylver.bruneau@gmail.com> */ - .phys_io = ORION5X_REGS_PHYS_BASE, - .io_pg_offst = ((ORION5X_REGS_VIRT_BASE) >> 18) & 0xFFFC, - .boot_params = 0x00000100, + .atag_offset = 0x100, .init_machine = qnap_ts409_init, .map_io = orion5x_map_io, + .init_early = orion5x_init_early, .init_irq = orion5x_init_irq, - .timer = &orion5x_timer, + .init_time = orion5x_timer_init, .fixup = tag_fixup_mem32, + .restart = orion5x_restart, MACHINE_END |